P/N 82207853AD - PDF file
Contents
1. Le syst me produit un bip a double tonalit La radio repasse au volume pr r gl Voir les instructions d utilisation dans le manuel de l appareil 01 12 2004 20 of 20 K68586812. Dial system should reply Phone Not Available 3 Push UConnect button again System prompts with a dual tone beep Radio will return to preset volume Please follow included Owner s Manual for system operation O PROCEDIMIENTO DE VERIFICACI N FUNCIONAL 1 Gire la llave de Encendido hacia la posici n ON y encienda el radio Ambos indicadores de luz color mbar en el coj n de control UConnect se encender n por un momento 3 segundos aprox 2 Presione el bot n UConnect en el coj n de control Un aviso del sistema anunciar UConnect Ready UConnect Listo El radio quedar en silencio Diga Dial Marcar El sistema debe responder Phone Not Available Tel fono no disponible 3 Presione el bot n UConnect nuevamente SEI sistema responder con un sonido de dos tonos El volumen del radio regresar a su valor preestablecido Para operar el sistema siga las instrucciones que parecen en el Manual del Propietario O V RIFICATION DU FONCTIONNEMENT 1 Mettre le contact et allumer la radio Les deux t moins jaunes du pav de commande Uconnect s allument bri vement environ 3 secondes 2 Appuyer sur le bouton Uconnect du pav de commande Un message vocal annonce lt lt Uconnect Ready gt gt La radio se met en sourdine Dire lt lt Dial gt gt le syst me doit r pondre lt lt Phone Not Available gt gt 3 Appuyer de nouveau sur le bouton UConnect
3. Install tie straps and mounting screws if needed ITEM B Measure for bracket mounting holes as shown in illustrations Using the bracket as a template drill two 1 8 holes Install bracket with supplied screws ITEM C Install speaker to mounting bracket Position speaker as shown in illustrations Tighten thumb screw with flat blade screwdriver do not overtighten ITEM D Remove backing from 2 way tape at underside of microphone Install mic to overhead console or dome lamp if equipped Using a small circular file make a notch in the console dome lamp bezel edge closest to the mic Route mic cable under headliner towards left A pillar ITEM E Secure control pad cable inside trough at the back of the unit Remove backing from 2 way tape at underside of control pad Install control pad to I P center console bezel using a small circular file make a notch in the inner edge of the radio or HVAC opening closest to the control pad 01 12 2004 2 of 20 K685868 1 1990 2001 VEHICLES GREY RADIO CONNECTOR 01 12 2004 5 of 20 K685868 1 JEEP GRAND CHEROKEE ES FUNCTIONAL CHECK PROCEDURE 1 Turn Ignition key to On position and turn radio on Both amber light indicators on the UConnect control pad will illuminate momentarily approx 3 seconds 2 Press UConnect Button on the control pad System prompt will announce UConnect Ready Radio audio will mute Say
4. MOPAR CONCORDE SEBRING SEDAN TOWN amp COUNTRY PACIFICA 01 12 2004 STRATUS CARAVAN DURANGO DAKOTA 2004 DURANGO 15 16 1 of 20 K6858681 IMPORTANT NOTES Disconnect and isolate negative battery cable Disconnect and remove overhead console or dome lamp if equipped Remove left driver s side A pillar trim panel and left NP access panel Remove I P center cluster bezel Disconnect and remove radio Remove knee blocker panel s Install kit components as described in notes and as shown in illustrations Ensure that all vehicle mounting surfaces are clean Route Item F 22 way connectors and Item E cable connector up into the I P at the knee blocker opening and out of the radio opening Keep away from sharp edges heat sources or moving parts 2002 2004 Vehicles Plug Item F 22 way connectors into radio and radio connector 1990 2001 Vehicles Follow procedure shown on page 5 Securely crimp a ground eyelet or a blade terminal to the black wire Make electrical connections to items A C D and E Loop up slack in harness and cables Apply tie straps and stow away neatly Do not kink or tightly coil the cables Re install vehicle components and trim panels ensuring that cables are not pinched under them Perform a functional check of the system by following the steps shown on page 20 of this document ITEM A Place supplied 2 way tape to underside of module Ensure tape contacts to vehicle mounting surfaces
Download Pdf Manuals
Related Search