Home

The Zonix™ - Fanimation

image

Contents

1. How to Wire Your Ceiling Fan A WARNING To avoid possible electrical shock be sure electricity is turned off at the main fuse box before hanging Figure 1 NOTE If you are not sure if the outlet box is grounded contact a licensed electrician for advice as it must be grounded for safe operation NOTE The hand held remote included with this fan has 16 different code combinations To prevent possible interference from or to other remote units simply change the combination code in your transmitter and receiver 1 To set the transmitter code remove battery cover by pressing firmly below arrow and sliding cover off Slide code switches to your choice of up or down position Factory setting is all up Do not use this position With a small screwdriver or ball point pen slide firmly up or down Replace battery cover on the transmitter Figure 2 2 To set the receiver unit code slide code switches to the same positions as set on your transmitter Figure 3 3 Slide the receiver unit into the open end of the hanger bracket Figure 4 4 Connect green wires from hanger bracket and hanger ball to bare ground wire using wire connector supplied Connect black wire from receiver unit marked AC IN L to black supply wire using wire connector supplied Connect white wire from receiver unit marked AC IN N to white supply wire using wire connector supplied Connect white wire
2. 30 Ilustraci n del despiece cccceeee eee ee teen eee rro 36 Este manual est dise ado para facilitar al m ximo el ensamblaje la instalaci n el funcionamiento y el mantenimiento de su ventilador de techo Herramientas necesarias Materiales para el ensamblaje La caja de distribuci n el ctrica y los conectores de la caja deben ser del tipo requerido por el c digo local El cable m s peque o debe ser un cable de tres conductores de dos conductores con conexi n a tierra del siguiente tama o tama o del cable seg n el A W G longitud del cable instalado Calibre de Alambre Estadounidense hasta 15 2 m 50 pies 14 de 15 2 a 30 5 m 50 a 100 pies 12 NOTA coloque las piezas de las bolsas de piezas individuales en un contenedor peque o para evitar que se extrav en Si faltan piezas p n gase en contacto con su proveedor local e Pelacables Tres conectores de cables incluidos A ADVERTENCIA Antes de ensamblar el ventilador de techo consulte la secci n sobre el m todo correcto de instalaci n el ctrica del e Destornillador Phillips e Escalera de tijera e Destornillador de Y ventilador p gina 29 Si siente que no posee la experiencia o los conocimientos el ctricos necesarios contrate a un electricista autorizado para instalar el ventilador Instrucciones para el desempaque Para su comodidad marque cada uno de los pasos A medida que completa cada paso coloque una m
3. 2 Instale el soporte de control con los dos tornillos 6 32x 1 Empuje los cuatro tapones de pl stico para cubrir los orificios de los tornillos Incluidos con el mando Figura 2 Figura 1 Figura 2 C mo instalar su mando a distancia Opci n 3 1 Taladre dos orificios de 1 4 en la pared y utilice los tacos de pl stico M6 para colocarlos en dichos orificios Instale el soporte de control con los tornillos autorroscantes 3 1 Empuje los cuatro tapones de pl stico para cubrir los orificios de los tornillos Incluidos con el mando Figura 1 33 Soluci n de problemas A ADVERTENCIA Para su propia seguridad desconecte la electricidad de la caja de fusibles o disyuntor antes de solucionar problemas en su ventilador Causa posible Soluci n sugerida 1 EL VENTILADOR NO ARRANCA 2 EL VENTILADOR HACE RUIDO 3 EL VENTILADOR OSCILA EN EXCESO 4 NO HAY SUFICIENTE MOVIMIENTO DE AIRE 1 El fusible o el disyuntor est n fundidos 2 Las conexiones el ctricas del ventilador o del interruptor en la caja del interruptor est n flojas 3 El conmutador inversor se encuentra en posici n neutra 4 Sin bater a en el control remoto 1 Las aspas no est n sujetas al ventilador 2 Hay tornillos flojos en la caja del motor 3 Los tornillos que aseguran los soportes de las aspas al buje del motor est n flojos 4 Los conectores de cables dentro de la caja hacen ruido 5 Ruido del mo
4. PARA REDUCIR EL RIESGO DE DESCARGAS EL CTRICAS ESTE VENTILADOR SE DEBE INSTALAR CON UN CONTROL INTERRUPTOR DE PARED AISLADO ADVERTENCIA Este producto est dise ado para ser usado s lo con las piezas suministradas o los accesorios indicados especificamente para el mismo Si utiliza piezas o accesorios que no est n indicados para su uso con este producto podr a sufrir lesiones personales o da ar el ventilador ADVERTENCIA Este producto est dise ado para ser usado s lo con las piezas suministradas o los accesorios indicados espec ficamente para el mismo Si utiliza piezas o accesorios que no est n indicados para su uso con este producto podr a sufrir lesiones personales o da ar el ventilador ADVERTENCIA Para reducir el riesgo de lesiones personales no doble los soportes de las aspas borde o soporte de aspas al instalar los soportes balancear las aspas o limpiar el ventilador No coloque objetos extra os entre las aspas del ventilador en funcionamiento ADVERTENCIA Monte a una caja de salida aceptable para apoyo de los aficionados 1 Este equipo no causar interferencias perjudiciales y 2 este equipo tolerar cualquier interferencia recibida incluidas las interferencias que puedan provocar un funcionamiento no deseado Si el radiador intencional puede ser clasificado como un dispositivo digital de clase B o un perif rico del ordenador entonces se deber n incluir los siguientes o equivalentes Nota Tras someterlo a las pruebas
5. AP814804 Receiver Unit RECAN55 Hand Held Remote TR24WH Loose Hardware Bag HDWFP4650 Wire Connector 4 Blade Balance Kit Blade Mounting Hardware Bag 3 16 24 x 11 mm Washer Head Screws with Fiber Washers 10 Phillips Screwdriver 4 CO JN O 0O1 A OI PO Insert FINISH CODES Refer to fan model number located on downrod support Before discarding packaging material be certain all parts have been removed HOW TO ORDER REPAIR PARTS When ordering repair parts always give the following information e Part Number e Part Description e Fan Model Number Contact your retail store for repair parts 16 The Zonix Model FP4650 Exploded View Figure 1 NOTE The illustration shown is not to scale or its actual configuration may vary Product parts are subject to change without notice FANIMATION cEILING FAN S 10983 Bennett Parkway Zionsville IN 46077 888 567 2055 FAX 866 482 5215 Outside U S call 317 733 4113 Copyright 2013 Fanimation Visit Our Website www fanimation com 2013 08 V 01 The Zonix Ventilador de techo Peso neto 8 12 kg 17 90 Ibs Modelo N 2 FP4650 MANUAL DEL PROPIETARIO LEA Y GUARDE ESTAS INSTRUCCIONES Instrucciones de seguridad importantes ADVERTENCIA Siga estas instrucciones para prevenir incendios descargas el ctricas y lesiones personales graves Lea el manual del propietario y la
6. Figura 2 Pasador NT Pasador de horquilla Figura 2 3 Afloje los dos tornillos de fijaci n del soporte del p Cables Negro Azul y barral Introduzca los cables de color negro azul y c blanco a trav s de la varilla Figura 3 Blanco Bola para colgar Tornillo de fijaci n 2 4 Coloque el soporte de la varilla y alinee los orificios de la clavija de horquilla en ambas piezas Instale la clavija de horquilla y aseg rela con la pinza de horquilla Fije los dos tornillos de presi n y las tuercas de seguridad en el soporte de la varilla Tornillo de Pasador de horquilla interior Figura 4 fijaci n 2 ADVERTENCIA Es fundamental que instale correctamente el pasador Bola para colgar de horquilla en el soporte de la varilla y que ajuste firmemente los tornillos de fijaci n y las tuercas El incumplimiento de dicho paso podr a hacer que el ventilador se caiga 5 Pase los cables a trav s de la cubierta de uni n del motor la cubierta para el tornillo y el capuch n Figura 5 Cubierta de gb la cubierta del union del motor tornillo de la base 26 C mo ensamblar el ventilador de techo cont 7 Vuelva a colocar la semiesfera en el barral como se indica a continuaci n Pase los tres cables de 2 03 m 80 a trav s de la semiesfera Pase el pasador a trav s de los dos orificios en el barral y alinee la semiesfer
7. Reorient or relocate the receiving antenna Increase the separation between the equipment and the receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Note For a Class A digital device statements of 15 105 a must be included when appropriate for the device in question LIMITED LIFETIME WARRANTY Extends to the original purchaser of a Fanimation Fan LIMITED LIFETIME MOTOR WARRANTY If any part of your fan motor fails due to a defect in materials or workmanship during the lifetime of the original purchaser Fanimation will provide the replacement part free of charge when the defective fan is returned to our national service center Proof of purchase is required Customer shall be responsible for all costs incurred in the removal or reinstallation and shipping of the product for repairs or replacement ONE YEAR MOTOR LABOR WARRANTY If your fan motor fails at any time within one year from the original purchase due to defects in materials or workmanship labor to repair the motor will be provided free of charge at our national service center Purchaser will be responsible for labor charges after this one year period Customer shall be responsible for all costs incurred in the removal or reinstallation and shipping of the product for repairs or replacement lf any other part of your fan fails at any time withi
8. correspondientes se ha determinado que este equipo cumple con los l mites establecidos para dispositivos digitales de Clase B de conformidad con la parte 15 de la Normativa FCC Estos l mites se han establecido con el objetivo de aportar una protecci n razonable contra interferencias perjudiciales cuando el equipo se utiliza en el hogar Este equipo genera utiliza y puede emitir energ a de radiofrecuencia y a menos que se instale y se utilice de acuerdo con el manual de instrucciones puede provocar interferencias perjudiciales en las comunicaciones por radio y televisi n Si el equipo produce interferencias perjudiciales en la recepci n de radio o televisi n lo cual puede probarse encendiendo y apagando el equipo se recomienda al usuario corregir dichas interferencias tomando una o varias de las siguientes medidas Modificar la orientaci n o ubicaci n de la antena de recepci n Aumentar la separaci n entre el equipo y el receptor Conectar el equipo a una toma de corriente o circuito diferente al del receptor Consulte al distribuidor o a un t cnico especialista de radio o TV para obtener m s ayuda Nota Para un dispositivo digital de clase A la declaraci n de 15 105 a debe ser incluida cuando sea apropiada para el dispositivo en GARANT A LIMITADA DE POR VIDA Se extiende al comprador original de un ventilador Fanimation GARANT A LIMITADA DE POR VIDA DEL MOTOR Si se produjera una falla en alguna de las partes del motor de
9. del capuch n AP260 Cubierta de uni n del motor AP1115 Unidad del motor del ventilador AMA4650 Juego de aspas BPW4426 Cubierta del interruptor de la carcasa de soporte P462009BL Unidad de vidrio AP465011 Unidad de luz LED AP814804 Receptor RECAN55 Mano a distancia TR24WH Bolsa de accesorios HDWFP4650 Conectores de cables 4 Kit de balanceo Bolsa de accesorios para el montaje de aspas Tornillos con cabeza de arandela de 3 16 24 x 11 mm con arandelas de fibra 10 Destornillador Phillips de 4 CO JN O 0O1 BY OINI Inserte los C DIGOS DE ACABADO consulte el n mero de modelo del ventilador que se encuentra en el soporte de barral Antes de desechar los materiales de embalaje aseg rese de haber extra do todas las piezas C mo hacer un pedido de piezas Al hacer un pedido de piezas de repuesto proporcione siempre la siguiente informaci n N mero de pieza e Descripci n de la pieza ___ N mero de modelo del ventilador P ngase en contacto con su tienda para obtener las plezas de repuesto 35 The Zonix Modelo FP4650 Despiece Figura 1 NOTA la ilustraci n que se muestra no est hecha a escala y su configuraci n real puede variar FANIMATION CEILING FANS 10983 Bennett Parkway Zionsville IN 46077 Llame sin cargo al 888 567 2055 FAX 866 482 5215 Desde fuera de los EE UU llame al 317 733 4113 Copyright 2
10. descargas el ctricas aseg rese de A 1 40 que la electricidad est desconectada en la caja de fusibles principal antes de realizar la instalaci n el ctrica Figura 1 NOTA Si no est seguro de si la caja de distribuci n el ctrica tiene conexi n a tierra pida asesoramiento a un electricista autorizado ya que la conexi n a tierra es Figura 1 z H PRINCIPAL CAJA DE FUSIBLES H On I OnA1 fond fon E loff o off O off o off o I0 40 H oo 1 uoj 4O UO H fundamental para un funcionamiento seguro NOTA El mando a distancia incluido en este ventilador tiene 16 combinaciones diferentes de c digos Para evitar E i etalle del transmisor posibles interferencias desde o hacia otros mandos a remoto distancia modifique el c digo de combinaci n de su transmisor y receptor 1 Para configurar el c digo del transmisor extraiga la carcasa de la bater a presionando firmemente debajo de la flecha y deslice la carcasa hasta extraerla Mueva los interruptores de c digo hasta colocar el c digo de selecci n en la posici n arriba o abajo Los ajustes de Figura 2 f bricas vienen con todos los interruptores hacia arriba No utilice esta posici n Con un destornilador peque o o con una lapicera deslice firmemente hacia arriba o hacia Detalle del la abajo Figura 2 unidad del receptor 2 Par
11. fan must be grounded as a precaution against possible electrical shock Electrical installation should be made or approved by a licensed electrician The fan base must be securely mounted and capable of reliably supporting at least 35 Ibs fan and accessories not to exceed 35 Ibs or 15 88 kgs See page 5 of owner s manual for support requirements Consult a qualified electrician if in doubt The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental contact with the fan blades Follow the recommended instructions for the proper method of wiring your ceiling fan If you do not have adequate electrical knowledge or experience have your fan installed by licensed electrician Suitable for use with solid state speed controls For supply connections if the conductor of a fan is identified as a grounded conductor then it should be connected to a grounded conductor power supply If the conductor of a fan is identified as an ungrounded conductor then it should be connected to an ungrounded conductor power supply If the conductor of a fan is identified for equipment grounding then it should be connected to an equipment grounding conductor WARNING TO REDUCE THE RISK OF ELECTRIC SHOCK THIS FAN MUST BE INSTALLED WITH A GENERAL USE ISOLATING WALL CONTROL SWITCH WARNING This product is designed to use only those parts supplied with this product and or accessories designated specifically for use with this p
12. from receiver unit marked TO MOTOR N to white wire from fan using wire connector supplied with receiver Connect black wire from receiver unit marked TO MOTOR L to black wire from fan using wire connector supplied Lastly connect blue wire from receiver to the blue fan light wire using wire connector supplied Position all connected wires and receiver antenna to allow installation of ceiling canopy Figure 5 5 After splicing and making the wire connections the wires should be spread apart and turned upward with the grounded conductor and the equipment grounding conductor on one side of the outlet box and the ungrounded conductor on the other side of the outlet box Figure 5 10 H E MAIN FUSE BOX 10 40 A 10 40 140 YO 1vuo On l On l B On l U Off O off o off o off o A 1 40 Figure 1 Remote Transmitter Unit Detail Ad3L1v8g _ ZE0ZYO AE x Receiver Unit Detail Figure 3 RECEIVER UNIT HANGER BRACKET Listed Outlet Box Green Wire Ground mea J l gt I i Green Wire 4 I Ground from AN E gt Y Hanger Bowl Green Wire Ground from Hanger Bracket Figure 5 How to Install Your Canopy Housing NOTE This step is applicable after the neccessary wiring is completed 1 Remove one of the two shoul
13. not sufficient To avoid possible electrical shock be sure electricity is turned off at the main fuse box before wiring All wiring must be in accordance with National and Local codes and the ceiling fan must be properly gro deg as a precaution against possible electrical shock A WARNING To avoid fire or shock follow all wiring instructions carefully Any electrical work not described in these instructions should be done or approved by a licensed electrician OUTLET BOX Figure 3 How to Assemble Your Ceiling Fan 1 Remove the hanger ball portion from the downrod hanger ball assembly by loosening the set screw in the hanger ball until the ball falls freely down the downrod Remove the pin from the downrod then remove the hanger ball Retain the pin and hanger ball for reinstal lation in Step 6 Figure 1 2 Remove the hairpin clip and clevis pin from the bottom of the downrod Retain the pin and clip for reinstallation in Step 4 Figure 2 3 Loosen the two set screws in the downrod support of the motor assembly Route the black white and blue wires through the downrod Figure 3 4 Slide downrod into the downrod support on top of the motor Install the clevis pin by aligning the holes in the downrod support with holes in the downrod Secure clevis pin with hairpin clip Tighten the two set screws with nuts in the downrod support Fi
14. 013 Fanimation Visite nuestro sitio Web en www fanimation com 2013 08 V 01
15. The Zonix Ceiling Fan Net Weight 17 90 Ibs 8 12 kg Model No FP4650 OWNER S MANUAL READ AND SAVE THESE INSTRUCTIONS CEILING FANS Important Safety Instructions WARNING To avoid fire shock and serious personal injury follow these instructions Read your owner s manual and safety information before installing your new fan Review the accompanying assembly diagrams Before servicing or cleaning unit switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally When the service disconnecting means cannot be locked securely fasten a warning device such as a tag to the service panel Be careful of the fan and blades when cleaning painting or working near the fan Always turn off the power to the ceiling fan before servicing Do not insert anything into the fan blades while the fan is operating Do not operate reversing switch until fan blades have come to a complete stop The appliance is not intended for use by young children or infirm persons without supervision Young children should be supervised to ensure that they do not play with the appliance Additional Safety Instructions To avoid possible shock be sure electricity is turned off at the fuse box before wiring and do not operate fan without blades All wiring and installation procedures must satisfy National Electrical Codes ANSI NFPA 70 1999 and Local Codes The ceiling
16. a configurar el c digo de unidad del receptor Deslice los interruptores de c digo a las mismas posiciones que en el transmisor Figura 3 3 Deslice la unidad del receptor en el extremo abierto del soporte colgante Figura 4 4 Conecte los cables verdes desde el soporte Figura 3 colgante y la bola colgante en el cable desnudo toma de tierra utilizando el conector de cables suministrado Conecte el cable negro desde la unidad del receptor marcado AC IN L al cable negro de suministro de electricidad utilizando el conector de cables suministrado Conecte el cable blanco desde la unidad del receptor marcado AC IN N al cable blanco de suministro de electricidad utilizando el conector de cables suministrado Conecte el cable blanco desde la unidad del soporte colgante receptor marcado TO MOTOR N al cable blanco del ventilador utilizando el conector de cables suministrado con el receptor Conecte el cable blanco desde la unidad del receptor marcado TO MOTOR L al cable blanco del ventilador SI utilizando el conector de cables suministrado con A el receptor Por ltimo conecte el cable azul del h Bianca CORRIENTES TADS receptor al cable azul de la luz del ventilador j 3 Tome de iene utilizando el conector de cables suministrado Coloque todos los cables conectados y la antena del receptor para permitir la instalaci n de la SS SF oro vero cubierta del techo Figura 5 UA de ia bola colg
17. a de modo que el pasador quede atrapado en la ranura de la parte superior de la misma Empuje la semiesfera hacia arriba bien ajustada contra el pasador Ajuste firmemente el tornillo de fijaci n en la semiesfera Si el tornillo de fijaci n est flojo podr a provocar oscilaci n del ventilador Figura 6 8 Corte el exceso de cable aproximadamente de 15 a 23 cm 6 a 9 pulgadas por encima de la parte superior del barral Pele 1 2 cm 7 del aislamiento en cada extremo del cable Figura 7 NOTA Se deben revisar todos los tornillos de fijaci n y volver a ajustarlos cuando sea necesario antes de realizar la instalaci n 27 C mo colgar el ventilador de techo ADVERTENCIA Para evitar una posible descarga el ctrica aseg rese de cortar la alimentaci n el ctrica de la caja de fusibles principal antes de colgar el ventilador Figura 1 NOTA Si no est seguro de si la caja de salida tiene conexi n a tierra pida consejo a un electricista certificado ya que debe tener conexi n a tierra para un funcionamiento seguro ADVERTENCIA Debe colgar el ventilador a una distancia m nima de 2 1 m desde las aspas hasta el piso Figura 2 1 Fije bien la abrazadera para colgar a la caja de salida con los tornillos y las arandelas provistas con la ventilador de techo Figura 3 ADVERTENCIA La caja de salida debe estar bien asegurada La abrazadera para colgar debe estar bien a
18. ad del kit de iluminaci n Receptor a N m f l Y y f W nE a i o o 7 5 o Unidad del motor 0 Bolsas de accesorios del ventilador J uego de aspas Uso eficiente de la energia El nivel de rendimiento y ahorro de energ a de los ventiladores detecho dependen de su correcta instalaci n yuso Acontinuaci n le presentamos algunas sugerencias para asegurar un rendimiento eficiente del producto Selecci n del lugar de montaje adecuado Los ventiladores de techo se deben instalar en el centro de la habitaci n a 2 13 m 7 pies de altura del piso como m nimo y 0 5 m 18 pulgadas de las paredes Si la altura del techo lo permite instale el ventilador a 2 5 m 8 9 pies por encima del suelo para un flujo de aire ptimo Consulte en su tienda minorista de Fanimation para obtener accesorios de montaje opcionales Apague el ventilador cuando no se encuentre en la habitaci n Los ventiladores son para refrescar a la gente no a las habitaciones Si la habitaci n est vac a apague el ventilador de techo para ahorrar energ a en ventiladores de techo Uso del ventilador de techo todo el a o En verano Use el ventilador de techo en sentido contrario a las agujas del reloj El flujo de aire que produce el ventilador crear un efecto fr o del aire que lo refrescar m s Seleccione una velocidad que le proporcione una brisa confortable Las velocidades m s ba
19. anta 5 Luego de empalmar los cables y realizar la conexi n gt A a sep relos y d blelos hacia arriba con el conductor con conexi n a tierra y el conductor con conexi n a tierra del equipo debe ir en un lado de la caja de distribuci n el ctrica y el conductor sin conexi n a tierra debe ir del otro lado Figura 5 UNIDAD DEL RECEPTOR Figura 5 29 C mo instalar la carcasa de la cubierta NOTA Este paso se debe realizar luego de completar la completed instalaci n el ctrica necesaria 4 ADVERTENCIA Para evitar posibles incendios o descargas el ctricas aseg rese de que los cables el ctricos vuelta hacia arriba Cubierta de y completamente empujarse con cuidado en el cuadro de uni n del motor juntura y de que no est n aprisio el techo Figura 1 1 Extraiga una de los tornillos de hombro en el soporte del gancho Afloje el segundo tornillo de hombro sin extraiga completamente Instale la cubierta rotando la ranura clave en la cubierta sobre el tornillo de hombro del soporte del gancho Fije el tornillo de hombro Instale adecuadamente y fije el segundo tornillo de hombro que fue anteriormente guardado Figura 1 Cubierta para el 2 Coloque y ajuste firmemente la cubierta para el tornillo tornillo del de la base sobre los tornillos de reborde de la capuch n abrazadera para colgar mediante el mecanismo de seguro por giro del chav
20. arca de verificaci n Con esto se asegurar de completar todos los pasos y podr saber desde d nde retomar si fuera interrumpido ADVERTENCIA e Unidad del motor del ventilador Bolsas de accesorios Unidad del soporte de Tornillos con cabeza de suspensi n is No instale ni utilice el ventilador si falta alguna pieza e Unidad del barral de la arandela de 3 16 24 x 11 semiesfera mm con arandelas de fibra o si hay piezas dafiadas Este producto esta disefiado para ser usado solo con las piezas suministradas o los accesorios indicados por Fanimation especificamente para el mismo La sustituci n de piezas 0 accesorios no designados por Fanimation para usar con este producto e Capuch n de techo e Cubierta para el tornillo del capuch n e Cubierta de uni n del motor e Unidad del kit de iluminaci n Destornillador Phillips de 4 Conectores de cables Kit de balanceo Mano a distancia Receptor e Vidrio Juego de aspas podr a ocasionar lesiones personales o da os en el ventilador P ngase en contacto con su tienda si faltan piezas o hay piezas da adas 1 Verifique que haya recibido las siguientes piezas NOTA Si no est seguro de la descripci n de una pieza consulte la ilustraci n del despiece Cubierta de uni n del motor Cubierta para el tornillo del capuch n soporte de a suspensi n Capuch n de techo Unidad del barral de la semiesfera Mano a distancia Unid
21. as correctamente incluyendo la toma de tierra y que no H A H A PRINCIPAL CAJA DE FUSIBLES vuoj uoj uo uo 0 40 A jooj 0 40 A On l On I On On l H Off O off o off o off o se visualizan ningun cable pelado en los conectores de cables con la excepci n del cable de toma de tierra No utilice el ventilador hasta que las palas est n colocadas en su lugar ya que de lo contrario se podria causar ruido y dafios Figura 1 j j 3V CR2032 2 Para que funcione el ventilador instale dos pilas de bater a de 3 voltios en el transmisor del mando a distancia dos piezas si no se va a utilizar porlargosperiodos de tiempo retire la bater a para evitar da os alcontrol remoto de MANDO A mano Guarde el transmisor lejos del exceso de calor DISTANCIA o humedad Figura 2 3 El transmisor del mando a distancia de 5 botones incluye 5 botones para controlar las velocidades baja media y alta del ventilador as como el encendido y apagado del mismo Se dispone de niveles de luces infinitos manteniendo pulsado el MANDO A DISTANCIA bot n on off Figura 3 BES BOTONES 4 Si se desea que el flujo del aire vaya en la direcci n opuesta apague el ventilador y espere a que se detengan las palas Deslice la carcasa de la cubierta para visualizar el interruptor de
22. ca a da os por instalaci n incorrecta negligencia accidentes uso indebido exposici n al calor o a la humedad en exceso o como resultado de cualquier modificaci n realizada al producto original Todos los gastos de remoci n y reinstalaci n del ventilador son responsabilidad exclusiva del propietario y no de la tienda que vendi el ventilador ni de Fanimation Fanimation se reserva el derecho de modificar o discontinuar un producto en cualquier momento o sustituir cualquier pieza seg n lo establecido por esta garant a GARANTIA LIMITADA DE POR VIDA Se extiende al comprador original de un ventilador Fanimation 8 En ning n caso se podr devolver un ventilador sin previa autorizaci n por parte de Fanimation Las devoluciones autorizadas deber n ir acompa adas del recibo de venta y deber n enviarse a Fanimation previo pago del flete El ventilador que se devuelva deber estar embalado en forma adecuada a fin de evitar da os durante el transporte Fanimation no se har responsable de los da os que resulten del embalaje incorrecto del producto 9 Se entiende que las reparaciones y las sustituciones son el nico recurso disponible de Fanimation No existe ninguna otra garant a expresa o impl cita Por la presente Fanimation niega todas las garant as impl citas que incluyen entre otras la comerciabilidad y la aptitud para determinado fin hasta donde la ley lo permita Algunos estados no permiten limitaciones sobre las ga
23. der screws in the hanger bracket Loosen the second shoulder screw without fully removing it Assemble canopy by rotating key slot in canopy over shoulder screw in G iling Canopy hanger bracket Tighten shoulder screw Fully assemble and tighten second shoulder screw that was previously removed Figure 1 WARNING Figure 1 To avoid possible fire or shock make sure that the electrical wires are completely inside the canopy housing and not pinched between the housing and the ceiling 2 Securely attach and tighten the canopy screw cover over the shoulder screws in the hanger bracket utilizing the keyslot twist lock feature Figrue 2 Canopy Screw Cover Do not connect fan blades until the fan is completely installed Installing the fan with blades assembled may result in damage to the fan blades A WARNING To reduce the risk of personal injury do not bend the blades when installing balancing or cleaning the fan Do not insert foreign objects in between the rotating blades 1 Carefully slide the blade through the slot as shown Figure 1 3 16 24 x 11 mm 2 Securely fasten the three blades with washer head Washer Head Screw with screws with fiber washers Do not over tighten Fiber Washer 3 per blade Figure 2 Figure 2 HARDWARE USED 3 16 24 x 11 mm WASHER HEAD x 9 SCREWS FIBER WASHER 11 How
24. eaker before trouble shooting your fan Probable Cause Suggested Remedy Fuse or circuit breaker blown 1 Check main and branch circuit fuses or circuit breakers 2 Check line wire connections to fan and switch wire connections in the switch housings CAUTION Make sure main power is turned off Loose power line connections to the fan or loose switch wire connections 1 FAN WILL in the switch housing NOT START 2 FAN SOUNDS NOISY Reversing switch in neutral position Dead battery in remote control Blades not attached to fan Loose screws in motor housing Screws securing fan blade holders to motor flywheel are loose Wire connectors inside housing rattling Make sure reversing switch position is all the way to one side Replace with new battery Attach blades to fan before operating Check to make sure all screws in motor housing are snug do not overtighten Check to make sure the screws which attach the fan blade holders to the motor flywheel are tight Check to make sure wire connectors in switch housing are not rattling against each other or against the interior wall of the switch housing CAUTION Make sure main power is turned off 5 Some fan motors are sensitive to 3 FAN WOBBLES EXCESSIVELY 4 NOT ENOUGH AIR MOVEMENT Motor noise caused by solid state variable speed control Screws holding blades to blade holders are loose S
25. eiling Fan Blades 11 Exploded View Illustration oooooomoo o 17 This manual is designed to make it as easy as possible for you to assemble install operate and maintain your ceiling fan Tools Needed for Assembly Materials One Phillips head screwdriver e One wire stripper Wiring outlet box and box connectors must be of type e One stepladder e One 1 4 blade required by the local code The minimum wire would be a e Three wire connectors supplied screwdriver 3 conductor 2 wire with ground of the following size Installed Wire Length Wire Size A W G Up to 50 ft 14 WARNING 50 100 ft 12 Before assembling your ceiling fan refer to section on proper method of wiring your fan page 10 If you NOTE Place the parts from the loose parts bags in a small feel you do not have enough wiring knowledge or container to keep them from being lost If any parts are experience have your fan installed by a licensed missing contact your local retailer electrician Unpacking Instructions For your convenience check off boxes are provided next to each step As each step is completed place a check mark in the box This will insure that all steps have been completed and will be helpful in finding your place should you be interrupted e Fan Motor Assembly Hardware bags a WARNING e Hanger Bracket Assembly Ten 3 16 24 x 11 mm F Downrod Hanger Ball Assembly Washer Hand Scr
26. etero Figura 2 C mo ensamblar las aspas del ventilador de techo NOTA DE INSTALACI N No conecte las aspas hasta que el ventilador est totalmente instalado Instalar el ventilador con las aspas colocadas podr a ocasionar da os en las mismas Unidad del motor A ADVERTENCIA Para reducir el riesgo de lesiones personales no doble las aspas al instalar balancear o limpiar el ventilador No coloque objetos extra os entre las aspas del ventilador en funcionamiento Ensamblaje de las aspas 1 Deslice con cuidado las aspas a trav s de la ranura como se muestra Figura 1 2 Asegure bien las tres aspas con tornillos con cabeza de arandela con arandelas de fibra No ajuste demasiado Figura 2 S Tornillos con cabeza de arandela de 3 16 24 x 11 mm con arandelas de fibra 3 por aspa Aditamentos utilizados Tornillos con cabeza x 9 de arandela de 3 16 24 x 11 Arandelas de fibra 30 C mo ensamblar los kit de luz 1 Extraiga los tres tornillos de la unidad del kit de iluminaci n y separe la cubierta del interruptor de Cubierta del interruptor de la carcasa de soporte del kit de iluminaci n Guarde la carcasa de soporte los tornillos para despu s Figura 1 Unidad del kit de iluminaci n 2 Extraiga uno de los cuatro tornillos del soporte ubicado en la parte inferior de la unidad del motor Afloje levemente los otros tres tornill
27. etscrew in downrod support is loose Setscrew in downrod hanger ball assembly is loose Screws securing fan blade holders to blades are loose Blade holders not seated properly Hanger bracket and or ceiling outlet box is not securely fastened Fan blades out of balance 15 signals from solid state variable speed controls Solid state controls are not recommended choose an alternative control method Tighten screws securely Tighten both setscrews securely in downrod support Tighten the setscrew in the downrod hanger ball assembly Check to be sure screws which attach the fan blade holders to the blades are tight Check to be sure the fan blade holders seat firmly and uniformly to the surface of the motor housing If holders are seated incorrectly loosen the screws and retighten Tighten the hanger bracket screws to the outlet box and secure outlet box Balance blades using balance kit provided in hardware bag If possible consider using a longer downrod For example use a 12 downrod instead of the 6 downrod that comes with your fan Parts List Model No FP4650 CT TS Hanger Bracket Assembly AP255BL Hanger Ball Downrod Assembly ADR1 6 Canopy PG154 Canopy Screw Cover Assembly AP260 Motor Coupling Cover AP1115 Fan Motor Assembly AMA4650 Blade Set BPW4426 Support Cover Switch Cup P462009BL Glass Assembly AP465011 LED Assembly
28. ews Do not install or use fan if any part is damaged or Ceiling Canopy with Fiber Washers missing This product is designed to use only those aa x parts supplied with this product and or any Canopy Screw Cover Assembly Phillips Screwdriver 4 accessories designated specifically for use with this Motor Coupling Cover Assembly Four Wire Connectors product by Fanimation Substitution of parts or Light Kit Assembly Balance Kit accessories not designated for use with this product Hand Held Remote Control by Fanimation could result in personal injury or Receiver Unit property damage Glass Blade Set 1 Check to see that you have received the following parts NOTE If you are uncertain of part description refer to exploded view illustration MN e Canopy Screw Motor Coupling Cover Assembly Hanger Bracket Cover Assembly Assembly Ceiling Canopy Downrod Hanger Ball Assembly Hand Held Light Kit Assembly Receiver Remote Control Unit o o o Fan Motor Blade Set Assembly Hardware Bag Energy Efficient Use of Ceiling Fans Ceiling fan performance and energy savings rely heavily on the proper installation and use of the ceiling fan Here are a few tips to ensure efficient product performance Choosing the Appropriate Mounting Location Ceiling fans should be installed or mounted in the middle of the room and at least 7 feet above the floor and 18 inches from t
29. gure 4 WARNING It is critical that the clevis pin in the downrod support is properly installed and the set screws and nuts are securely tightened Failure to do so could result in the fan falling 5 Route wires through Motor Coupling Cover Canopy Screw Cover and Ceiling Canopy Figure 5 Set Screw Hairpin Clip DD T Clevis Pin Figure 2 Black White and QD Blue wires Downrod Set Screws 2 Set Screws and Clevis Pin Locking Nuts 2 Motor Coupling Cover How to Assemble Your Ceiling Fan continued 6 Reinstall the hanger ball on the downrod as follows Route the three 80 in wires through the hanger ball Position the pin through the two holes in the downrod and align the hanger ball so the pin is captured in the groove in the top of the hanger ball Pull the hanger ball up tight against the pin Securely tighten the set screw in the hanger ball A loose set screw could create fan wobble Figure 6 7 Cut off excess lead wire approximately 6 to 9 inches above top of the top of the downrod Strip insulation off 1 2 inch from the end of each lead wire Figure 7 NOTE All set screws must be checked and retightened where necessary before installation How to Hang Your Ceiling Fan WARNING To avoid possible fire or shock be sure electricity is turned off at the main fuse box before hanging Figure 1 NOTE If you are not sure if t
30. he outlet box is grounded contact a licensed electrician for advise as it must be grounded for safe operation WARNING The fan must be hung with at least 7 of clearance from floor to blades Figure 2 1 Securely attach the hanger bracket to the outlet box using the outlet box screws and washers supplied with the outlet box Figure 3 A WARNING The outlet box must be securely anchored Hanger bracket must seat firmly against outlet box If the outlet box is recessed remove wall board until bracket contacts box If bracket and or outlet box are not securely attached the fan could wobble or fall 2 Carefully lift the fan and seat the downrod hanger ball assembly on the hanger bracket that was just attached to the outlet box Be sure the groove in the ball is lined up with tab on the hanger bracket Figure 4 A WARNING Failure to seat tab in groove could cause damage to electrical wires and possible shock or fire hazard ls WARNING O WARNING To avoid possible shock do not pinch wires between the hanger ball assembly and the hanger bracket A loff o off o orto off o uo Io jo uo MAIN FUSE BOX On I On font fond z ooj 0 40 0 40 0 40 q Figure 1 dy Washers UY SCREW 2 Supplied with P Outlet Box TAB Ll Figure 4
31. he walls If ceiling height allows install the fan 8 9 feet above the floor for optimal airflow Consult your Fanimation Retailer for optional mounting accessories Turn Off When Not in the Room Ceiling fans cool people not rooms If the room is unoccupied turn off the ceiling fan to save energy Using the Ceiling Fan Year Round Summer Season Use the ceiling fan in the counter clockwise direction The airflow produced by the ceiling fan creates a wind chill effect making you feel cooler Select a fan speed that provides a comfortable breeze lower speeds consume less energy Winter Season Reverse the motor and operate the ceiling fan at low speed in the clockwise direction This produces a gentle updraft which forces warm air near the ceiling down into the occupied space Remember to adjust your thermostat when using your ceiling fan additional energy and dollar savings could be realized with this simple step Electrical and Structural Requirements Your new ceiling fan will require a grounded electrical supply line of 120 volts AC 60 HZ 15 Amp Circuit Electrical code requires use of a fan rated outlet box to support the extra weight and motion associated with a ceiling fan A fan rated box will be labeled as such and typically supports up to a 70lb ceiling fan Fan Rated Outlet Boxes vary in ratings and design Ensure the ratings of your ceiling fan outlet box meet the requirements for the ceiling fan being installed F
32. igure 1 Figure 2 and Figure 3 depicts different structural configurations that may be used for mounting the outlet box Low profile usage diagram idea Figure 1 A 12 in deep pancake box is meant to be screwed to a joist or block It s used if only one cable is coming into the box It is also available in a saddle mount configuration Deeper profile usage diagram idea Figure 2 A 2 14 in deep box can be attached to blocking between joists and is roomy enough to handle more than one cable OUTLET BOX Figure 1 CEILING JOIST Electrical and Structural Requirements Continued No blocking Figure 3 Paired with a deep box this hanger is meant to span between two joists and takes the place of wooden blocking A WARNING To reduce the risk of fire electrical shock or personal injury mount fan to outlet box marked acceptable for fan support of 15 88 kg 35 Ibs or less Use screws supplied with outlet box Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced Consult a qualified electrician if in doubt If your fan is to replace an existing light fixture turn electricity off at the main fuse box at this time and remove the existing light fixture A WARNING Turning off wall switch is
33. iling fan is the only maintenance that is needed When cleaning use CAUTION only a soft brush or lint free cloth to avoid scratching the finish Abrasive cleaning agents are not required and should be avoided to prevent damage to finish Do not use water when cleaning your ceiling fan It could damage the motor or the finish and create the possibility of electrical shock How to Clean Your Ceiling Fan Blades Periodic light dusting of the blades is recommended Avoid using water cleansers or harsh rags which A feather duster will work best can warp and ruin the finish 13 How to Install Your Remote Control Option 1 1 Unthread two screws from the wall switch plate Figure 1 2 Install the control bracket with two 6 32x 3 4 screws And push the four plastic plug to cover the screw holes Including in the control Figure 2 Figure 2 1 Unthread two screws from the wall switch plate Figure 1 2 Install the control bracket with two 6 32x 1 screws And push the four plastic plug to cover the screw holes Including in the control Figure 2 Figure 1 1 Drill the two 1 4 holes in wall and use the M6 plastic anchor pushed into the holes Install the control bracket with two 3 1 self tap screws Push the four plastic plug to cover the screw holes Including in the control Figure 1 14 Trouble Shooting A WARNING For your own safety turn off power at fuse box or circuit br
34. informaci n de seguridad antes de instalar su nuevo ventilador Observe los diagramas de ensamblaje adjuntos Antes de llevar a cabo el mantenimiento o la limpieza de la unidad desconecte la electricidad en el panel de servicio y bloquee los medios de desconexi n del mismo para evitar que se active accidentalmente Si no se pueden bloquear los medios de desconexi n del servicio coloque un dispositivo de advertencia como una etiqueta en el panel de servicio Tenga cuidado con la estructura y las aspas del ventilador cuando limpie pinte o trabaje cerca del mismo Desconecte siempre la electricidad del ventilador de techo antes de llevar a cabo el mantenimiento No coloque nada en las aspas del ventilador cuando ste se encuentra en funcionamiento No accione el conmutador inversor hasta que las aspas del ventilador se hayan detenido por completo El dispositivo no ha sido dise ador para ser utilizado por ni os o personas enfermas sin supervisi n Los ni os deben ser supervisados para asegurarse de que no juegan con el dispositivo Instrucciones de seguridad adicionales Para evitar posibles descargas el ctricas aseg rese de que la electricidad est desconectada en la caja de fusibles antes de realizar la instalaci n el ctrica y no haga funcionar el ventilador sin las aspas Todos los procedimientos de conexi n el ctrica e instalaci n deben cumplir con los C digos el ctricos nacionales ANSI NFPA 70 1999 y C digos
35. jas consumen menos energ a En invierno Invierta el motor y haga funcionar el ventilador de techo a velocidad baja y en el sentido de las agujas del reloj Esto produce una suave corriente ascendente que obliga al aire c lido que se acumula cerca del techo a bajar al espacio ocupado No olvide ajustar el termostato cuando utilice el ventilador de techo Con este sencillo paso puede ahorrar energ a adicional y dinero Requisitos el ctricos y estructurales Su nuevo ventilador de techo requiere una l nea de suministro el ctrico con conexi n a tierra de 120 voltios de CA 60 Hz circuito de 15 amperios La normativa el ctrica requiere el uso de una caja de distribuci n el ctrica para ventiladores que soporte el peso extra y el movimiento asociado a un ventilador de techo La caja de distribuci n el ctrica ser etiquetada como tal y soportar un ventilador de techo de un peso de hasta 70 libras Dichas cajas var an en tipos y dise os Aseg rese d que el tipo de su caja re ne los criterios para el ventilador que se est instalando Las ilustraciones 1 2 y 3 muestran las diferentes configuraciones estructurales que pueden ser utilizadas para dicha caja de distribuci n el ctrica Idea de diagrama de uso de perfil bajo Figura 1 La caja lisa de 1 2 pulgada de profundidad ser atornillada a una viga o bloque Se utilizar si solo un cable va a ser introducido en la caja Tambi n est disponible en una configuraci n de mon
36. l reverso Figurea 4 Informaci n sobre el interruptor de reversa Temporada Posici n del interruptor Verano En direcci n contraria _ Izquierda del Reversa a las manecillas del reloj Invierno En direcci n de las Derecha manecillasdel reloj Figura 4 Mantenimiento 1 El nico mantenimiento necesario para el ventilador de PRECAUCI N techo es una limpieza peri dica Al llevar a cabo la limpieza use s lo un cepillo suave o un No utilice solventes para limpiar el ventilador de techo pa o sin pelusas para evitar rayar el acabado Podr an da ar el motor o las aspas y ocasionar posibles i i NE descargas el ctricas No se requieren agentes abrasivos de limpieza los mismos deben evitarse para prevenir da os en el acabado C mo limpiar su aspas del ventilador Se recomienda limpiar peri dicamente el polvo de las palas Un guardapolvos de pluma ser la mejor soluci n de limpieza Evite el uso de agua limpiadores o trapos speros que podr an combar o da ar las palas 32 C mo instalar su mando a distancia Opci n 1 1 Retire los dos tornillos colocados en la plaza del interruptor de la pared Figura 1 2 Instale el soporte de control con los dos tornillos 6 32x 3 4 Empuje los cuatro tapones de pl stico para cubrir los orificios de los tornillos Incluidos con el mando Figura 2 Figura 2 1 Retire los dos tornillos colocados en la plaza del interruptor de la pared Figura 1
37. locales El ventilador de techo debe estar conectado a tierra a fin de prevenir posibles descargas el ctricas La instalaci n el ctrica debe ser llevada a cabo o aprobada por un electricista autorizado Se debe fijar bien la base del ventilador sta debe ser capaz de soportar sin problemas al menos 15 9 kg 35 Ib Consulte la p gina 21 del manual del propietario para ver los requisitos de soporte Si tiene dudas consulte a un electricista calificado Las aspas del ventilador deben instalarse por lo menos a 2 13 m 7 pies del suelo a fin de evitar un contacto accidental con las mismas Siga las recomendaciones sobre el m todo correcto de instalaci n el ctrica de su ventilador de techo Si no posee la experiencia o los conocimientos el ctricos adecuados contrate a un electricista autorizado para instalar el ventilador Apto para usar con controles de velocidad de estado s lido En lo que respecta a las conexiones de suministro si el conductor del ventilador est identificado como conductor con conexi n a tierra se le debe conectar a un suministro de electricidad con conductor de puesta a tierra Si el conductor del ventilador est identificado como conductor que no es de puesta a tierra se le debe conectar a un suministro de electricidad con conductor sin puesta a tierra Si el conductor del ventilador est identificado para equipos de puesta a tierra se le debe conectar al conductor de equipos de puesta a tierra ADVERTENCIA
38. n hereby disclaims any and all implied warranties including but not limited to those of merchantability and fitness for a particular purpose to the extent permitted by law Some states do not allow limitations on implied warranties Fanimation will not be liable for incidental consequential or special damages arising out of or in conjunction with product use or performance except as may otherwise be accorded by law This warranty gives you special legal rights and you may also have other rights that vary from state to state 10 A certain amount of wobble is normal and should not be considered a problem or a defect Table of Contents Unpacking Instructions lt lt lt lt o0oococoncrranna nos 4 How to Assemble the Light Kit oo oooo 12 Energy Efficient Use of Ceiling Fans 5 How to Operate Your Ceiling Fan o o oooo 12 Electrical and Structural Requirements 5 Maintenance o ococcccoccn eee eee eee 12 How to Assemble Your Ceiling Fan 7 How to Clean Your Ceiling Fan Blades 12 How to Hang Your Ceiling Fan o oooooommom o 9 How to Install Your Remote Control 14 How to Wire Your Ceiling Fan 0 00 cece eee eee 10 Trouble Shooting orrir 202 ee res ci eed 15 How to Install Your Canopy Housing 11 Parts List svssssrnaserskekakvars eee testes nna nne 16 How to Assemble the C
39. n one year after original purchase due to a defect in materials or workmanship we will repair or replace at our option the defective part free of charge for parts and labor performed at our national service center Because of varying climate conditions this warranty does not cover changes in the finish including rusting pitting corroding tarnishing or peeling This warranty is void and does not apply to damage from improper installation neglect accident misuse exposure to extremes of heat or humidity or as a result of any modification to the original product All costs of removal and reinstallation of the fan are the sole responsibility of the owner of the fan and not the store that sold the fan or Fanimation LIMITED LIFETIME WARRANTY Extends to the original purchaser of a Fanimation Fan Fanimation reserves the right to modify or discontinue any product at any time and may substitute any part under this warranty Under no circumstances may a fan be returned without prior authorization from Fanimation The receipt of purchase must accompany authorized returns and must be sent freight prepaid to Fanimation The fan to be returned must be properly packed to avoid damage in transit Fanimation will not be responsible for any damage resulting from improper packaging It is understood that any repair or replacement is the exclusive remedy available from Fanimation There is no other expressed or implied warranty Fanimatio
40. os Instale la cubierta del interruptor de la carcasa de soporte en el soporte utilizando las dos ranuras principales de cubierta del interruptor de la carcasa de soporte Vuelva a colocar el cuarto tornillo y asegure los cuatro tornillos Figura 2 3 Instale el conector de 2 clavijas desde la kit de iluminaci n conexi n a la unidad del motor Figura 3 PRECAUCI N A fin de reducir el riesgo descargas el ctricas Unidad del motor desconecte el circuito de suministro el ctrico al ventilador antes de instalar el kit de iluminaci n c gt Kit de iluminaci n 4 Ensamble la kit de iluminaci n de cubierta del Figura 3 interruptor de la carcasa de soporte con los tornillos que quit anteriormente Figura 4 PRECAUCI N La fuente de luz est dise ado para esta aplicaci n espec fica y puede recalentarse si reparado por personal no capacitado Si se requiere ning n tipo de servicio el producto debe ser devuelto a un centro de servicio autorizado para su revisi n o reparaci n 5 Asegure el vidrio en la unidad de la placa de luz gir ndolo en el sentido de las agujas del reloj y sin apretar demasiado Figura 5 Kit de iluminaci n Vidrio 31 C mo utilizar su ventilador de techo 1 Restaure la fuente de alimentaci n de la toma de corriente enciendo la electricidad del fusible principal Figura 1 A ADVERTENCIA Compruebe que todas las conexiones realizad
41. rant as impl citas Fanimation no se har responsable por da os accidentales resultantes o especiales derivados del uso o el rendimiento del producto o en conjunci n con ste excepto en los casos en los que la ley as lo disponga Esta garant a le otorga derechos legales especiales y es posible que tambi n goce de otros derechos que pueden variar seg n el estado 10 Es normal que se produzca un cierto movimiento oscilante y esto no debe considerarse un problema o defecto Tabla de contenidos Instrucciones para el desempaque o oooocococonococr cr 23 Como ensamblar los kit de luz cocooooocooroommmmmm 31 Uso eficiente de la energ a en ventiladores de techo 24 C mo utilizar su ventilador de tech0 ooooooccccoocc ccoo 32 Requisitos el ctricos y estructurales ooooommmmmm 24 Mantenimiento oooccocccnncnnc nn rr 32 C mo ensamblar el ventilador de techo ooooocommoo 26 C mo limpiar su aspas del ventilador 32 C mo colgar el ventilador de tech0 00ocooccoccocoo ro 28 Como Instalar su Mando a Distancia ooooomooo 33 C mo realizar la instalaci n el ctrica del ventilador de techo 29 Soluci n de problemas cece cece eee eee e eee e aes 34 C mo instalar la carcasa de la cubierta 30 Lista de piezas 0 occiiiiniinicaro ria 35 C mo ensamblar las aspas del ventilador de techo
42. red interior de la caja del interruptor PRECAUCI N Aseg rese de que el suministro principal de electricidad est desconectado 5 Algunos motores de ventilador son sensibles a las se ales de los controles de velocidad de estado s lido variables Los controles de estado s lido no son recomendables Escoja un m todo de control alternativo 6 Ajuste bien los tornillos 1 Ajuste bien los dos tornillos de fijaci n y las tuercas en el soporte de barral 2 Ajuste el tornillo de fijaci n en la unidad del barral de la semiesfera 3 Aseg rese de que los tornillos que fijan los soportes de aspas al buje del motor del ventilador est n bien ajustados 4 Aseg rese de que los soportes de las aspas del ventilador est n colocados firmemente y de manera uniforme en relaci n con la superficie de la caja del motor Si los soportes est n mal colocados afloje los tornillos y vuelva a ajustarlos 5 Ajuste los tornillos del soporte de suspensi n de la caja de distribuci n el ctrica y aseg rela 6 Equilibre las palas utilizando el kit de equilibrio suministrado en la bolsa del hardware 1 Si es posible considere el uso de un barral m s largo Por ejemplo no incluido usted puede comprar el tiempo de la vara hacia abajo fanimation com Lista de piezas Modelos N FP4650 Unidad del soporte de suspensi n AP255BL Unidad del barral de la semiesfera ADR1 6 Capuch n de techo PG154 Cubierta para el tornillo
43. roduct Using parts and or accessories not designated for use with this product could result in personal injury or property damage WARNING To reduce the risk of personal injury do not bend the blade bracket flange or blade holder when installing the brackets balancing the blades or cleaning the fan Do not insert foreign objects in between rotating fan blades WARNING Mount to an outlet box marked acceptable for fan support This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation If the intentional radiator can be classified as a Class B digital device or a PC peripheral then shall include the following or equivalent Note This equipment has been tested and found to comply with the limits for Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures
44. sentada contra la caja de salida Si la caja de salida est empotrada retire el panel hasta que la abrazadera haga contacto con la caja Si la abrazadera y o la caja de salida no est n bien aseguradas el ventilador podr a tambalearse o caerse 2 Levante cuidadosamente el ventilador y coloque el ensamble de la bola para colgar varilla en la abrazadera para colgar que acaba de fijar a la caja de salida Aseg rese de que la ranura de la bola est alineada con la lengueta de la abrazadera para colgar Figura 4 ADVERTENCIA Si no coloca la leng eta en la ranura podr an da arse los cables el ctricos y podr an ocurrir incendios o descargas el ctricas ADVERTENCIA Para evitar una posible descarga el ctrica no apriete los cables entre el ensamble de la bola para colgar y la abrazadera para colgar 28 H E a O On l On l PRINCIPAL CAJA DE FUSIBLES q E 10 40 0 40 E 10 40 uoj vuoj uo 110 Ioff o off o off o oft o Figura 1 2 1 m 7 pies como minimo Caja de distribuci n ra el ctrica Arandela Plana Tornillos 2 con la ventilador de techo Figura 3 Caja de distribuci n el ctrica Soporte de suspensi n Unidad del barral de la semiesfera Figura 4 C mo realizar la instalaci n el ctrica del ventilador de techo AADVERTENCIA Para evitar posibles
45. su ventilador debido a un defecto en los materiales o en la fabricaci n durante el tiempo de vida del comprador original Fanimation proporcionar la pieza de repuesto sin cargo una vez que el ventilador defectuoso sea devuelto a nuestro centro de servicios nacional Se requiere comprobante de venta El cliente se har responsable de todos los gastos de remoci n o reinstalaci n y env o del producto para reparaciones o sustituci n GARANT A DE MANO DE OBRA DEL MOTOR POR UN A O Si el motor de su ventilador fallara antes de cumplirse un a o a partir del momento de su compra original debido a defectos en los materiales o en la fabricaci n se le efectuar la reparaci n del mismo sin cargo en nuestro centro de servicios nacional El comprador se har responsable de los gastos de mano de obra luego del per odo de un a o El cliente se har responsable de todos los gastos de remoci n o reinstalaci n y env o del producto para reparaciones o sustituci n Si otra pieza del ventilador fallara dentro del per odo de un a o a partir de la fecha de compra original debido a un defecto en los materiales o en la fabricaci n repararemos o sustituiremos seg n creamos conveniente la pieza defectuosa sin cargo alguno en nuestro centro de servicios nacional Debido a las diversas condiciones clim ticas esta garant a no cubre cambios en la terminaci n incluidos oxidaci n corrosi n falta de brillo o peladuras Esta garant a es nula y no se apli
46. ta ocasi n y extraiga la unidad de iluminaci n ADVERTENCIA Apagar el interruptor de pared no es suficiente Para evitar posibles descargas el ctricas aseg rese de que la electricidad est desconectada en la caja de fusibles principal antes de realizar la instalaci n el ctrica Toda instalaci n el ctrica debe cumplir con los c digos nacionales y locales y el ventilador de techo debe tener la conexi n a tierra adecuada como forma de precauci n ante posibles descargas el ctricas A ADVERTENCIA A fin de evitar incendios o descargas el ctricas siga con cuidado todas las instrucciones de instalaci n el ctrica Cualquier trabajo el ctrico que no se describa en estas instrucciones deber ser realizado o aprobado por un electricista autorizado 25 distribuci n el ctrica C mo ensamblar el ventilador de techo 1 Extraiga la pieza de la bola colgante de la unidad Pasador de la bola colgante varilla aflojando el tornillo de presi n de la bola colgante hasta que la bola se libere de la varilla Retire el pasador del barral y Bola para colgar luego extraiga la semiesfera Conserve el pasador y la semiesfera para su reinstalaci n en el Paso 6 Figura 1 Ranura de la bola colgante de fijaci n 2 Retire el clip de horquilla y pasador de horquilla de la parte inferior de la bola para colgar Retener el pasador y clip para la reinstalaci n en el paso 4
47. taje endosado Idea de diagrama de uso de perfil alto Figura 2 La caja de 2 1 4 pulgada ser atornillada a un bloque entre vigas que tenga suficiente espacio para colocar m s de un cable Vigas del techo Caja de distribuci n el ctrica Figura 1 Vigas del techo Caja de distribuci n Techo a el ctrica Figura 2 24 Requisitos el ctricos y estructurales cont No bloqueo Figura 3 Conectado a una caja de distribuci n el ctrica este colgador Vigas de echo sirve para abarcar el espacio entre dos vigas y ocupar el lugar de bloqueo de la madera AADVERTENCIA Para reducir el riesgo de incendios descargas el ctricas o lesiones personales fije el ventilador a la caja de distribuci n el ctrica marcada como aceptable para soporte de ventilador de 15 88kg 35Ib Utilice los tornillos suministrados con la caja de distribuci n el ctrica La mayor a de las cajas de distribuci n el ctricas que com nmente se utilizan como soporte de l mparas no son aptas para soporte de ventiladores y es posible que deban reemplazarse Consulte a un electricista calificado si tiene dudas Si su ventilador va a sustituir una instalaci n de iluminaci n Figura 3 existente desconecte la electricidad de la caja del fusible principal en es
48. to Assemble the Light Kit 1 Remove the three screws from the light kit assembly and separate the support cover switch cup from the light Support Cover Switch Cup kit housing Retain the screws for later Figure 1 2 Remove one of the four screws in the support bracket at the bottom of the motor assembly Slightly loosen the remaining three screws Assemble the support cover switch cup to the support bracket using the three key slots in the support cover switch cup Replace the fourth screw and securely tighten Figure 2 Support Cover Switch Cup 3 Connect the 2 single pin connectors from the light kit housing to the 2 single pin connectors from the motor assembly Figure 3 CAUTION To reduce the risk of electric shock disconnect the electrical supply circult to the fan before installing light kit Light Kit Housing 4 Assemble the light kit housing onto the support cover switch cup using the previously removed screws Figure 4 CAUTION The light source is designed for this specific application and can overheat if serviced by untrained personnel If any servicing is required the product should be returned to an authorized service facility for examination or repair 5 Secure the glass to light kit assembly by twisting in a clockwise direction Do not over tighten Figure 5 12 How to Operate Your Ceiling Fan 1 Restore electrical power to the outlet box by turning the electrici
49. tor provocado por el control de velocidad de estado s lido variable 6 Los tornillos que sujetan las aspas a los soportes de aspas est n flojos 1 El tornillo de fijaci n y la tuerca del soporte de barral est n flojos 2 El tornillo de fijaci n en la unidad del barral de la semiesfera est flojo 3 Los tornillos que aseguran los soportes de las aspas al buje del motor est n flojos 4 Los soportes de aspas no est n colocados correctamente 5 El soporte de suspensi n o la caja de distribuci n el ctrica del techo no est n bien asegurados 6 Las aspas del ventilador est n desbalanceadas 34 1 Controle los fusibles del circuito principal y derivado o los disyuntores 2 Controle las conexiones el ctricas del ventilador y del interruptor en las cajas de los interruptores PRECAUCI N Aseg rese de que el suministro principal de electricidad est desconectado 3 Aseg rese de que el conmutador inversor est completamente a un lado 4 Reemplace con una bater a nueva 1 Ajuste las aspas al ventilador antes de ponerlo en funcionamiento 2 Aseg rese de que todos los tornillos de la caja del motor est n bien ajustados pero no en exceso 3 Aseg rese de que los tornillos que fijan los soportes de aspas al buje del motor del ventilador est n bien ajustados 4 Aseg rese de que los conectores de cables en la caja del interruptor no produzcan ruido al rozar unos con otros O al rozar la pa
50. ty on at the main fuse box Figure 1 A WARNING Check to see that all connections are tight including ground and that no bare wire is visible at the wire H A H g MAIN FUSE BOX z On I OnA fond fon z loff o off o off o off o I0 g0 10 40 0 40 0 40 E vuoj vuo uo 1 40 connectors except for the ground wire Do not operate fan until the blades are in place Noise and fan damage could result Figure 1 2 To make fan operational install two 3 volt batteries 3V CR2032 included in the hand held remote transmitter If not BATTERY using for long periods of time remove battery to prevent 2 PCS damage to transmitter Store the remote away from REMOTE excessive heat or humidity Figure 2 CONTROL Figure 2 3 The 5 button hand held remote transmitter includes buttons for high medium and low fan speeds as well as fan off and light on off Figure 3 4 If airflow is desired in the opposite direction turn the fan off and wait for the blades to stop turning Slide the reverse switch on top of motor assembly to the opposite position and turn fan on again Figure 4 Reverse Switch Information Rotation Direction Switch Position Switch Summer Counter Clockwise Left Winter Clockwise Right Figure 4 Maintenance 1 Periodic cleaning of your new ce

Download Pdf Manuals

image

Related Search

Related Contents

SPH-DA120 - kellergruppe  ー2vの力一用品が大型車(24V)で楽しめる。  télécharger ce mode d`emploi au format PDF - SE  施工説明書/取扱説明書  Edelbrock 68752 Automobile Parts User Manual  Samsung Galaxy Tab 2 7.0 WiFi Felhasználói kézikönyv  取扱説明書 - パワーエンタープライズ POWER  Essonne le Mag 115 :Mise en page 1    Manuale Tecnico  

Copyright © All rights reserved.
Failed to retrieve file