Home

User Manual/Manual de usuario QMAX 231 - AV-iQ

image

Contents

1. jO LOUD SPEAKERS 04 J User Manual Manual de uso Pag 5 Control and Operation Q MAX 231 POWER CHANNEL 2 CHANNELA 1 10 12 1 Power Switch To turn the equalizer ON or OFF CAUTION All volume or level controls must be at 0 or minimum position before turning power on Always turn on your equalizer before your power amplifiers are turned on and always turn off your equalizer after the power amplifiers have been turn off 2 Filter Level controls each of these sliders control the output level of each of the 31 band pass filter Center detent position is ground for guaranteed flat response 3 Filter Range Switch The gain range of the filter sliders is switchable as a group from 6 dB to 12 dB for maximum boost cut capability 4 Bypass Use the bypass mode to compare equalized un unequalized material or the bypass the unit in the event of power loss When bypass the input signal is routed directly to output jack 5 Signal LED When LED light in green there is input signal the LED will flicker when any section of the equalizer is within 5 dB od clipping then tou should turn down
2. 2 Controles de nivel de filtro Cada uno de estos potenci metros controla el nivel de salida de cada uno de los 31 filtros paso banda La posici n central es masa para garantizar la respuesta plana 3 Conmutador de rango El rango de ganancia es conmutable como grupo desde 6 dB a 12 dB para un m ximo de realce corte 4 Bypass Use el modo bypass para comparar el material ecualizado y por ecualizar or para que la se al no se vea afectada por el paso a trav s del ecualizador En este modo la entrada es dirigida directamente a la salida 5 LED se al Cuando se ilumina el LED verde signifaca que hay se al de entrada si el LED parpadea alguna secci n del ecualizador est a 5 dB de clipear entonces debe reducir el nivel del ecualizador o de la unidad precedente para evitar la distorsi n User Manual Manual de uso Pag 16 Connection Example RA ry O of el om om 00909940 09 oloo oloo CHANNEL 299 og 910 oeg 300900909 001 929999 soso 5 68 m 1 os 1 09999 IS oe enn ee L _ _ M___ ___8_J 1 1 a PA a PA sass e u mami 1 m 999 faze f l i i sE gt lt m a CHANNEL 2 CHANNEL 1 Er a AS e
3. CE WORK Equipson S A www equipson es support equipson es All rights reserved 31 BAND 1 3 OCTAVE GRAPHIC EQUALIZER QMAX 231 User Manual Manual de usuario W QMAX 231 31 BAND STEREO EQUALIZER ECUALIZADOR ESTEREO DE 31 BANDAS English Version Page 1 Versi n Espa ol P gina 11 This symbol on the product or on its packaging indicates that this product shall not be trated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical an electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product The recycling of amterials will help to conserve natural resources For more detailed information sabout recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product Este s mbolo en su equipo o embalaje indica que el presente producto no puede ser tratado como residuos dom sticos normales sino que deben entregarse en el correspondiente punto de recogida de equipos electr nicos y el ctricos Asegur ndose de que este producto es desechado correctamente Ud est ayudando a prevenir las consecuencias negativas para el medio ambiente y la salud humana que podr an derivarse
4. Seleccione el rango 6 dB e 4 Aplique se al a su sistema Service O e renter rer cere ere eee rrr ee 5 Pulse bypass para salir de este modo 6 Si el LED clip se ilumina reduzca el nivel 7 Empiece a usar el ecualizador para configurar el sonido 8 Si no obtiene el nivel de ganancia necesario conmute al rango 12 dB 9 Si el el LED clip se ilumina continuamente baje el nivel hasta que este LED s lo se ilumine ocasionalmente Aplicaciones El ecualizador debe ser usado cuando se desee modificar la respuesta de frecuencia del sistema de audio Un ecualizador gr fico es una potente herramienta que soluciona gran n mero de problemas y crea interesantes texturas Avisos 1 Todas las instrucciones de funcionamiento deben ser le das antes de usas este equipo 2 Para reducir el riesgo de descargas el ctricas no retire las cubiertas superior e inferior dentro de la unidad no hay elementos de ajuste para el usuario Dirijase a un t cnico especializado 3 No exponga la unidad a luz solar directa o fuentes de calor como estufas radiadores u otras aplicaciones que generen calor User Manual Manual de uso Pag 18 User Manual Manual de uso Pag 3 Introduction We congratulate you on choosing a FLEPCHER equalizer You will find that its design makes using it very simple The stereo 31 band graphic equalizer with frequency control of 20 Hz to 20kHz and a incorporates constant Q circuitry with a 3 center frequency accuracy Specia
5. When the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet Protect the power cord from being walked on or pinched particularly at plugs convenience at plugs convenience receptacles and the point where they exit from the apparatus Only use power cord from attachments accessories specified by the manufacturer Use only with a cart stand bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over Unplug this apparatus during lightning storms or when unused for long Periods of time Refer all servicing to qualified service personal Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been Spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally User Manual Manual de uso Pag 2 4 Esta unidad debe ser limpiada s lo con un pa o sueva Evite usar disolventes u otros detergentes 5 Cuando mueva este equipo h galo dentro de su embalaje original para reducir el riesgo de da os Especificaciones Bandas de freciencia Tipo de filtro Dimen potenci metro Rango Conex de entrada Impedancia de salida Nivel Max de salidal Filtro Low Cut Filtro High Cut Respuesta de frecuencia THD N Relaci
6. n se al ruido Separaci n de canales Alimentaci n Consumo Dimensiones Peso 2x31 1 3 octava ISO Q constante 3 20mm y punto medio 6dB or 12dB seleccionable XLR y Euroblock balanceados lt 150 ohms 18dBm bal 22dBm desbal 10Hz a 250Hz 12dB oct 3Hz a 40kHz 12dB oct 20Hz a 20kHz 0 5dB 0 01 94dB gt 50dB 60dB 110V 230V 50 60Hz 12W 483 x 88 x 216 mm 4 1kg User Manual Manual de uso Pag 19 Contents Antes de comenzar a usar este ecualizador hay informacion que deberia conocer y procedimientos que seguir Su ecualizador esta equipado con un conmutador Bypass este conmutador cuando esta activado todas las ecualizaciones ser n canceladas mientras que la se al de entrada pasa a trav s de la unidad Introduction con ganancia unitaria Instruction for CONNECTIONS oc ee teereeteteeeteeeteteeeteees 4 El conmutador de rango permite configurar el maximo realce o corte de cada banda de ecualizaci n entre 6dBo 12 dB Si aplica demasiada ganancia a la se al de entrada el LED clip se iluminar En este caso Connection example is a TT debe reajustar el control de nivel Control and Operation 0 ccccccccseseseeeeeeeeeeeeeeeeesneneneteteees Aqu tiene algunos consejos para su configuraci n inicial WARRING Sisi naaa 1 Configure todos los controles de volumen a su posici n central 2 Configure todos los controles de frecuencia a su posici n central Specifications n a a a 3
7. 12 Use estantes o mesas especificadas por el fabricante cuando lo use tenga la precauci n de moverlo junto con la unidad para evitar ca das o da os 13 Desconecte la unidad durante tormentas el ctricas o si no va a usarlo durante largo tiempo A 4 Dirijase a un t cnico especializado ante cualquier problema en la unidad cable cortado o da ado liquido u objetos en el interior o el aparato ha estado expuesto a la lluvia o la humedad o no parezca funcionar con normalidad User Manual Manual de uso Pag 12 4 This unit should be cleaned only with a damp cloth Avoid solvents or other cleaning detergents 5 When moving this equipment it should be placed in its original carton and packing This will reduce the risk of damage in transit Specifications Frequency Bands Filter Type Slider Travel Range Input connections OUTPUT Impedance Max Output Level Low Cut Filter High Cut Filter Frequency Response 2x31 1 3 octave ISO spacing Constant Q 3 center accuracy 20mm positive center detect 6dB or 12dB selectable active balanced XLR and Eruo style strip Type lt 150 ohms 18dBm bal 22dBm unbal 10Hz to 250Hz 12dB oct 3Hz to 40kHz 12dB oct 20Hz to 20kHz 0 5dB THD Noise 0 01 Signal to Noise Ratio 94dB Channel separation gt 50dB 60dB Power 110V 230V 50 60Hz Power Consumption 12watts Dimension 3 5 H X19 W x 8 5 D 2U Weight 9 1bs 4 1kg User Manu
8. de la incorrecta manipulaci n de este producto EL reciclaje de materiales ayuda a conservar las reservas naturales Para recibir m s informaci n sobre el reciclaje de este producto contacte con su ayuntamiento su punto de recogida m s cercano o el distribuidor donde adquiri el producto Servicio The information furnished in this manual does not include all of the details of design and engineering Esta unidad dispone de una circuiteria electr nica muy sofisticada y s lo deber ser manejada por of this particular product not does it cover every possible application or situation concerning its personal especializado usage which may occur during the installation operation or maintenance of said FLEPCHER product CAUTION IMPORTANT a THE PRODUCT REQUIRES CLASS 2 OUTPUT WIRING Para prevenir el riesgo de descargas no retire las tapas no hay elementos de control para el usuario en el interior de la unidad Dirijase a un t cnico especializado A CAUTION A TO PREVENT ELECTRIC SHOCK DO NOT Shock Hazard Do Not Enter REMOVE TOP OR BOTTOM COVERS NO USER NA SERVICEABLE PARTS INSIDE REFER Elda el SERVICING TO QUALIFIED SERVICE Betel PERSONNEL DISCONNECT POWER CORD etrete BEFORE REMOVING REAR PANEL COVER TO Urto Hazard Do Non Entrano ACCESS GAIN SWITCH WARNING TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE Magnetic Field CAUTION Do not locate sensitive h
9. D Occasional flickering of the Clip LED is acceptable but if it remain on continuously you should turn down the level control or reduce the output level of the preceding component to avoid audible distortion Low Cut Filter or HPF The Low Cut filter rolls off decreases lower frequencies This is useful for decreasing rumble or low frequency hum from a signal Its range is adjustable from 10Hz to 250Hz Frequencies below this setting are rolled off while frequencies above are Unaffected Hi Cut Filter or LPF The Hi Cut filter rolls off decreases higher frequencies This is useful for reducing hiss or sibilance form a signal signal Its range is adjustable form 3kHz to 40kHz Frequencies above this setting are rolled off while frequencies above are unaffected Level Control This control sets the signal level coming into the equalizer Its full clockwise position is unity gain no boost or cut If the Clip LED is lit continuously turn down this control until it only flickers occasionally Power Cord This cord is used to connectAC power to your equalizer Never use a damaged or cut power cord Never use with the ground pin removed Fuse Holder The fuse holder contains the primary Ac fuse Only replace with the same type if necessary 0 6 amp If ever the fuse continues to blow after replacing stop using the EQ sand serviced by qualified personnel Balanced XLR connectors Pin1 Ground Pin2 Hot Pin3 Cold Balan
10. al Manual de uso Pag 9 Service This unit has very sophisticated circuitry and should only be serviced by a fully trained technician This is why each unit bears the following label CAUTION To prevent electric shock do not remove covers No user serviceable parts inside Refer servicing to a qualified technician User Manual Manual de uso Pag 10 IMPORTANTE ESTE PRODUCTO REQUIERE CABLEADO DE SALIDA CLASE 2 AX PRECAUCION A PARA PREVENIR EL RIESGO DE DESCARGA NO RETIRE LAS TAPAS SUPERIOR E INFERIOR NO HAY PARTES DE USO EN EL INTERIOR DIRIJASE A UN TECNICO ESPECIALIZADO DESCONECTE EL CABLE DE RED ANTES DE QUITAR LAS TAPAS X Shock Hazard Do Not Enter Choc Hasard N entrent Schocke Hazard Test Nicht Betrete Urto Hazard Do Non Entrano ATENCION PARA REDUCIR EL RIESGO DE DESCARGA NO EXPONGA LA UNIDAD A LA LLUVIA O HUMEDAD Campo Magnetico PRECAUCION No situe equipos de gran sensibilidad como previos o pletinas directamente sobre esta unidad debido al campo magnetico presente en estas unidades los cuales pueden inducir ruidos y zumbidos El triangulo le alerta del El punto de exclamaci n le alerta riesgo de descargas de una instrucci n importante User Manual Manual de uso Pag 11
11. ariable Bypass LED de umbral de sobrecarga conmutador de masa y selector de tensi n de entrada Instrucciones para el conexionado El ecualizador funciona con alimentaci n 220 240 V 50 60 Hz No elimine el pin central de masa en una nueva instalaci n o sistema port til confirme la alimentaci n y seleccione con el conmutador el voltaje apropiado antes de conectar cualquier instrumento Hay dos conexiones paralelas de entrada y salida Los conectores XLR y Euroblock est n balanceados La salida balanceada requiere que se use el pin 2 del XLR y Euroblock como y el pin 3 como El pin 1 ser masa El ecualizador est equipado con un conmutador de masa situado en el panel trasero Si despues de conectar el sistema se aprecia zumbidos el problema puede ser ocasionado por incompatibilidades de masa entre el ecualizador y otras unidades del sistema Utilice el conmutador para hacerlo desaparecer PRECAUCION APAGUE LOS AMPLIFICADORES ANTES DE CAMBIAR EL SISTEMA DE MASA Pruebe diferentes combinaciones conectando la masa de las unidades con la alimentaci n o asegur ndose que el chasis est conectado a la toma de tierra de la red Niveles de se al desde 10 dB a 4 dB son considerados normales y existe al menos 20 dB de resonancia No conecte micr fonos directamente al ecualizador stos necesitan preampificadores User Manual Manual de uso Pag 14 6 7 8 9 10 11 12 Clip LE
12. ced Euro terminal strip Pin1 Input signal Hot Pin2 Input signal Cold Pin3 Input signal Ground Pin4 Output signal Ground Pins Output signal Hot Pin6 Output signal Cold User Manual Manual de uso Pag 7 Before starting to use you equalizer there is some information you should know and procedures you should follow Youur equalizer is equipped with a bypass switch The bypass switch when active all equalization setting will be cancels while allowing signal to flow through the unit at unity gain A range control switch is provide which allows you to set maximum boost or cut for each band of equalization to either 6 dB or 12 dB If you apply to much gain to the input signal the clip LED will light If the clip light is on you must readjust the level control Here are some tips to help you with your initial setup 1 Set the level control to their center position 2 Set all frequency controls to their center position 3 Select the 6 dB range setting 4 Apply signal to your system 5 Take the unit out of bypass 6 If the clip light is on turn down the level control 7 Star using the equalizer to shape your sound 8 If do not have enough gain for your needs switch the range to 12 dB setting 9 In the clip LED lights continuosly while you are applying EQ turn down the level control until Clip LED light only occasionally Applications The equalizer may used wherever modification for the frequency contour of a so
13. de control para que s lo lo haga ocasionalmente 10 Cable de red Este cable es necesario para conectar la alimentaci n de su ecualizador Nunca use un cable da ado ni el cable con el pin de masa eliminado 11 Portafusible El portafusible contiene el fusible de alimentaci n Cambie s lo por otro de igual valor y tipo Si el fusible contin a fundi ndose consulte con un t cnico especializado 12 Conectores XLR balanceados Pin 1 masa Pin 2 Pin 3 Conectores Euroblock balanceados Pin 1 entrada de se al Pin 2 entrada de se al Pin 3 Masa de se al de entrada Pin 4 Masa de se al de salida Pin 5 salida de se al Pin 6 salida de se al User Manual Manual de uso Pag 17 Control y Funcionamiento CHANNEL 20 25 315 40 50 63 80 100 125 160 200 250 315 400 500 630 800 1K 125K 16K 2K 25K 315K 4K SK 63K 8K 10K 125K 16K 20K e Q MAX 231 o e owen o 31 BAND 1 3 OCTAVE GRAPHIC EQUALIZER o 65 34 7 CHANNEL 2 CHANNEL 1 11 10 12 1 Interruptor de red Permite conmutar el encendido apagado de la unidad PRECAUCION Todos los controles de nivel y volumen deben estar a 0 o a su posici n m nima antes de encender la unidad Siempre encienda el ecualizador antes de encender los amplificadores y siempre apague el ecualizador despues de haberlo hecho con los amplificadores
14. igh gain equipment such as preamplifiers or tape decks directly above or below this unit Because this amplifier has a high power density it has a strong magnetic field which can induce hum into unshielded devices that are located nearby This field is strongest just above and below the unit If an equipment rack is used we recommend locating the amplifier s at the bottom of the rack and the preamplifier or other sensitive equipment at the top Printed on recycled paper The lightning bolt triangle is The exclamation point triangle is used used alert the user to the risk to alert the user to important operating of electric shock and or maintenance instructions User Manual Manual de uso Pag 20 User Manual Manual de uso Pag 1 Important Safety Instructions 1 2 10 11 12 13 Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with a damp cloth Do not block any of the ventilation openings Install in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other apparatus that produce heat Do not install the safety purpose of he polarized or grounding type plug A polarized plug has two blades with one wide than the other A grounding type plug has two blades and third grounding prong The wide blade or the third prong is provided for your safety
15. ipment in the same system There are several combinations that can be attempted CAUTION Always turn your amplifiers down before changing your ground around Try different combinations of lifting ground on units that are supplied with ground lift switches or make sure all chassis are connected to earth ground either through the A C Power cord ground or by the front panel rack mount screws Signal levels from 10dB to 4dB are considered normal and at least 20dB of headroom exists above these levels Do not directly connect microphones into the equalizer Microphones require a pre amp User Manual Manual de uso Pag 4 6 LED Clip Un parpadeo ocasional de este LED is aceptable pero si luce continuamente debe reducir el nivel de salida de la unidad procedente 7 Filtro Low Cut o HPF Este filtro reduce las bajas frecuencias Es til p ara eliminar zumbido de baja frecuencia Su rango es ajustable desde 10 Hz a 250 Hz Las frecuencias por debajo de este nivel no se ven afectadas 8 Filtro High Cut o LPF Este filtro reduce las altas frecuencias Es til p ara eliminar soplidos de la se al Su rango es ajustable desde 3 kHz a 40 kHz Las frecuencias por encima de este nivel no se ven afectadas 9 Level Control Este contol controla el nivel de se al que entra en el ecualizador En su posici n en sentido horario es ganancia unitaria no hay realce ni reducci n Si el LED Clip parpadea totalmente baje el nivel
16. l features include selectable range 6dB or 12dB active balanced and unbalanced input output connectors RFI filters variable level control passive bypass switch overload threshold LED ground lift switch and selectable line voltage switch Instruction For Connections The equalizer is for operation from 220 240 volt 50 60Hz main supply Do not remove the center grounding pin in new installations and portable sound systems or any situation in which the mains power is in question it is wise to confirm the confirm the voltage and select the appropriate line voltage switch before connecting the instrument to power sources There are two paralleled input and output connectors XLR and Euro terminal are actively balanced with pin 2 or the tip being Hi Pin 3 or the ring being Lo and Pin 1 or sleeve being ground Balanced output requires using Pin 2 of the XLR or the tip of the Euro terminal as output Hi and using Pin 3 of the XLR or the ring of the Euro terminal as Lo It does not require Pin 1 or signal ground The signal exists differentially between the two balanced leads Ground is used only for shielding to prevent potential hum Paralleling input and output may be accomplished by using and of the three connectors The equalizer is equipped with a rear panel Ground lift switch After setting up your system and the system exhibits hum or buzzing the problem is that there is a ground incompatibility between your equalizer and other equ
17. the level or reduce the output level of the preceding component to audible distortion User Manual Manual de uso Pag 6 Ejemplo de conexionado Tae TTIE 60 e jo g ele 1910 0 1 lalalala oleate tp eaae ee 01910 0 0 0 0 010707 00la lalalala 0 joto ll loloojo 0 00 00 _ lojorojojojoj0 070703 PB 01010101010101010104 lojor0r0101010 010103 i oJo ajojoja o ojaja a 1 eadh i a ce as SG MEZCLADOR A ee A 1 y 1 QMX 231 1 1 1 i O O O NE of a GZ User Manual Manual de uso ALTAVOCES Introduccion Felicidades por la elecci n de un ecualizador WORK Encontrar que su dise o lo hace facil de utilizar La unidad incorpora un ecualizador gr fico de 31 bandas con control de frecuencia de 20 Hz a 20 kHz y circuiteria de Q constante con una correcci n de frecuencia central del 3 Sus caracter sticas especiales incluyen selector de rango 6 dB o 12 dB conectores de entrada salida balanceados y desbalanceados Filtros RF control de nivel v
18. und is needed A graphic equalizer is powerful tool for solving a numberr of audio problems and creating interesting textures Warnings 1 All operations isntruction should be read before using this equipment 2 To reduce the risk of electrical shock do not remove cover or back No user service part inside Refer servicing to a qualified service technician 3 Do not expose to direct sunlight or heat sources such radiators stoves or other aplliances that produce heat User Manual Manual de uso Pag 8 Contenidos Especificaciones A ditions ne User Manual Manual de uso Pag 13 Instrucciones Importantes de Seguridad 1 Lea estas instrucciones 2 Conserve estas instrucciones 3 Tenga presente todos los avisos 4 Sigua las instrucciones 5 No use este aparato cerca del agua 6 Limpie la unidad con un pafio humedo 7 No bloquee las aberturas de ventilaci n Inst lelo de acuerdo a las instrucciones del fabricante 8 No lo instale cerca de fuentes de calor como radiadores registros de calor estufas u otras aplicaciones que generen calor 9 Conecte la unidad con una clavija de toma de tierra para su propia seguridad en caso de que la clavija mural no disponga de ello consulte a un electricista 10 Proteja el cable de red contra pisadas o pinzamientos particularmente en las clavijas o donde sale de la unidad A 1 Use nicamente cable y accesorios especificados por el fabricante

Download Pdf Manuals

image

Related Search

Related Contents

取扱説明書 - 丸茂電機  9800 Series User Manual - HIK  Handbuch  Mai 2003 - Institut de Formation en Psychomotricité de Toulouse  フリービット(3843)    

Copyright © All rights reserved.
Failed to retrieve file