VFX-W - SHOEI
Contents
1. To install the visor affix the enclosed visor screws Snug the left and right screws but leave the center screw loose Adjust the angle of the visor to the desired height then snug the center visor screw Check all screws once more to ensure they are securely snug Never use any screw except for original SHOEI visor screws to prevent damage to the threaded inserts The visor could shatter under pressure or due to an impact Suitable goggles are recommended for extra eye protection Anti reflection Sticker For helmets so equipped stick the enclosed anti reflection sticker on the inner surface of2. To fit the nose cover align the flange on the lower part of the cover with the shell and secure it with the screw The nose filter inside the nose cover is removable Before refitting the nose cover check that the filter is aligned correctly and there are no gaps Ventilation System 0 1 DL ON i 9 Visor Peak Front Air Intake Top Air Outlet Shell Impact Absorbing Liner Rear Air Outlet Window Beading Lower Air Intake 9 Nose Cover 10 Side Air Outlet 11 Neck Outlet oN OO ORON Front Air Intake Top Air Outlet
3. EMERGENCY USE ONLY PULL RED RING INSIDE CHIN BAR AND REMOVE CHEEK PAD PULL RING TOME WPULL RING TO REMOVE CHEEKPAD EE REMOVECHEEKPAD by your hand when pulling out cheek pads Never pull the red ring while riding Use genuine SHOEI cheek pads only and never use non SHOEI Darts Do not use Emergency Quick Release System when removing a cheek pad for maintenance 4 Never peel these stickers from a helmet Removing and Installing the Neck Outlet A The neck outlet can be removed for cleaning To install it again insert
4. Center pad cheek pads and chinstrap covers of both sides can be removed for washing in this model Remove or install firmly referring to the names and drawings of the inner parts When you replace the inner parts be sure to select the proper size for your helmet Helmet Size XS S M L XL XXL For Loose Fit XS5 S5 M5 L5 XL5 5 Center Pad Standard XS9 S9 M9 L9 XL9 XL5 ForTightFit XS13 S13 M13 L13 XL13 XL9 For Loose Fit 31 31 31 31 31 Standard 35 35 35 35 35 31 For Tight Fit 39 39 39 39 39 35
5. 1 When installing or removing the inner parts hold near a snap and handle with care Press a head of the snap firmly until you hear it clicks 2 When you wash the inner parts wash by hand or put them in mesh bag in case of machine wash Use water only for washing wipe with dry cloth and dry in the shade An excessive wring may break a plate portion of the inner parts Wipe the impact absorbing liner polystyrene foam under the pads with a cloth moistened by water or a solution of neutral detergent in water Never use benzine thinner petrol or any kind of harsh cleaner as they may damage the parts ee WARNING 1
6. Before installing the cheek pad be sure the red plate is in the right position as shown in Drawing 12 Be sure that 2 snaps are positioned in red circles as indicated in the drawing and white portions of the snaps are fully exposed If the red plate is not in the right position the cheek pad may not fit properly 13 3 Identify right and left at first Then pass the chinstrap through the hollow portion of the cheek pad and snap the pad at all 3 points in the order of to as per Drawing 13 Press the head of the snap from the pad side until you hear it clicks 14 Cheek Pad Chinstrap 14
7. To remove a cheek pad in an emergency cut or undo a chinstrap first then hold a helmet firmly and pull a red ring inside a chin bar as per drawin9 Pulling the ring will move the plate and release snaps allowing a cheek pad to be pulled out through the bottom of a helmet while the helmet is still on the rider s head Do in the same manner to remove a cheek pad of the other side When removing cheek pads make sure to hold a helmet firmly and pay full attention not to move rider s head Warning 1 Make sure to hold the helmet firmly
8. 3 1 Before wearing the helmet make sure that visor s center and side screWs are Securely tightened A Visor coming loose while riding can be dangerous 2 Clean the helmet parts with a solution of neutral detergent and water rinse well and dry with a soft cloth Never use benzine thinner petrol or any kind of harsh cleaner as they may damage the parts 3 Make sure that all the inner parts are equipped before you use the helmetl
9. 9 7 Slide and insert front plate into a gap of bracket from one side to another as indicated in Drawings 7 and 9 10 10 Be sure that the plate of the center pad is secured as shown in Drawing 10 2 Snap 2 points into place in the rear of the center pad until you hear it clicks Installing the Cheek Pads 12 A
10. When installing the cheek pad be sure that the chinstrap passes through the es Cheek pad as Der Drawing 14 15 Cheek Pad Bracket A B Insert plates A and B at the bottom of the cheek pad into the 16 Cheek Pad Bracket cheek pad brackets until you hear it clicks Do both sides in the same manner E Q R S E Q R S Emergency Quick Release System E Q R S E Q R S Emergency Quick Release System is a mechanism for emergency personnel to remove the cheek pads 1
11. SHOEI Instructions for use Thank you for purchasing this SHOEI helmet Please read this manual carefully before use and keep it for future reference This manual contains valuable information to help you understand the functions of the product and the instructions for use in order for you to enjoy a safety and comfortable motorcycle life Your SHOEI dealer can provide a replacement if it is lost VFX W 179 Installing the Visor Peak
12. M 398 31 If you like to change fit of the standard center pad change to the option center pad referring to a table shown above Cheek pad is common for all helmet sizes If you like to change fit of the standard cheek pad change to the option cheek pad referring to a table above For example if you like to change fi of size M cheek pad tight change to the cheek pad 39 Conversely change to the cheek pad 31 if you like to make it loose Cheek pad and center pad differ for each helmet size When you replace make Cheek Pad sure to check your helmet size Make sure that all the inner parts are equipped before use Removing and Installing the Inner Parts 1 Removing the Cheek Pads
13. Rear Air Outlet Installing the Mud Guard A B A Insert the mud guard into a gap A between the shell and the impact absorbing liner as per drawing For portions of B flip a window beading and insert the mud guard in the same manner Don t hold the mud guard when carrying the helmet as it may become dislodged Q R I P Removable Inner Parts Q R I P System 3D 3D Full Support Inner 0 Center Pad Cheek Pad Right Cheek Pad Left Chinstrap Cover Right Chinstrap Cover Left Replacement of the Inner Parts
14. 5 5 Pull out a front portion of the center pad holding a plate as per Drawing 5 Removing and Installing the Chinstrap Covers To remove a chinstrap cover remove the cheek pad first release a snap and strip the cover from the chinstrap Do both sides in the same manner A cover differs right and left To install identify right and left referring to a drawing first Then pass the chinstrap through and snap until you hear it clicks Installing the Center Pad 7 Bracket Plate eee LL
15. 3 Unsnap 3 points and pull out cheek pad of both sides 2 Cheek Pad Bracket Plate A B Then pull out plates A and B in a bottom of a cheek pad from 3 Cheek Pad Bracket Plate cheek pad brackets Do both sides in the same manner Removing the Center Pad 4 ater PIN yu Remove the center pad from a rear head to a front portion Unsnap 2 points at center pad brackets Chinstrap Cover Chinstrap Cover Left Ia Chinstrap Cover Right Me 9
16. the visor Line up the cut portions of the sticker with the grooves in the visor as indicated in a drawindg Anti reflection sticker is not enclosed with black plain colored model lt 300 0525 1793 TEL 029 892 3617 E mail help shoeihelmet co jp SHOEI 110 0005 5 8 5 CP10 7F TEL 08 5688 5180 FAX 03 3837 8245 SHOEI CO LTD HEAD OFFICE 7TH FLOOR CP10 BLDG 5 8 5 UENO TAITO KU TOKYO JAPAN 110 0005 PHONE 03 5688 5170 FAX 03 3837 8245 www shoei com Printed in Japan 20100701 Removing and Installing the Nose Cover To remove the nose cover remove the screw and lift the nose cover slightly as per drawing
17. the right and left tabs of the plate into the gap between B the shell and the impact absorbing liner as per drawind A Insert the center tab into a bracket and check for secure fit Bracket ooo ooooooo ooooooooool o OOoooooooooooo oo 05 0 Oo 9 6ooool 6ooooooooooooo ooooooooooooo ooooooooooo O00 Ot oo00o0000000o0 0 o OOoooooo Keys for Handling the Inner Parts 1
Download Pdf Manuals
Related Search