フラット三脚取扱説明書
Contents
1. 1 2 H 3 4 5 6 7 8 12. English Thank you for choosing Benro Please read this 9eneral instructon sheet before using to avoid any accldental damade Do not exceed the load capacity of this products see the specifications MAX safety conditlon to avoid accldental damage of 1 Always ensure the locks and devices are in the camera and other edulpement Do not use the product at tempreture less than 20 C or more than 70C lis not recommended to use In seawater Avoid leaving the product in high tempreture e g in the sun for long tme or in a car near the car window for hours Ensure keepind the product out of reach of i children when working at the public place in case any accidental hurt Use it carefully in dangerous place Do not scrub the spirit level the precision Could be lost temporarly Remove the eduipment from the products during transportation 1 is not necessary to do regular lubrication but if required the standard lubricant oils and glease is ok for the equipment After using in the wet dusty sandy windy days it IS recommentded to clean and dry the tripod with soft
3. ES MAX A 0 AM4 2 1 A
4. 3 4 5 6 7 8 1 4 amp 3 8 9 3 8 amp 14 3 8 1 4 1 4 6 10 11 12 13
5. BENRO MAX 20 70 sy NO 1
6. 12 English SET UP Before using your tripod adjust each leg section to the desired height and leg angle setting Ensure that the tripod is frmly resting on alevel surface and mount your camera carefully on the tripod head Always engage safety locks on the tripod head to prevent any accidental dismounting Leg Section Adjustment See figure1 2 Each leg section can be Independently adjust to the desired length bytuming the proper led lock grip counter clockwise untl the leg is free to slide in or out Once the desire length is achieved turn the leg lock grip clock wise untl the leg section IS securely locked Repeat this step for each leg and eachsecton untl the tripod is set to the desired height For quick and easy setup each legsection excluding the last Section incorporates a key and groove within the leg to prevent the leg from rotating Combination of center column and tripod See figure3 4 5 The center column and tripod is packed separately if you need to use center column for adjusting the height please lock the center column on the top plate of the tripod Center Column is accessarles Darts you need to pay for itl Adjustment of Center column See figure6 7 8 Center column has two sections loosen the rubber grip of Column in Counter clockwise directio
7. 4 amp 3 8 9 3 8 amp 14 3 8 14 1 4 S 6 10 11 12 13 12 1 2
8. cloth The dirt dust and sand In all leg locks threads should be removed after use Clean with mild detergent or alcohol For your own safty dont let this products near any electrical power Source and chemical substances INSTRUCTIONS BENRO PROFESSIONAL TRIPOD gt NIATTSENINI TRAVELER SERIES Z989 8 85 5Z 18 XV4 1989 8 85 SZ 18 1 uedef 60 0S6 ee5IIN nonA eweAebeqn 6 9 L P11 0 3pel 3PIA doJuad dnu dn dapeJapIA Ja1seuuda 989 8 5C0 XV 1989 8 E GZ0 1 6 9 L 2 EZ60 0S6 7
9. n and adjust it to right position lock the rubber grip of column in clockwise direction then you can reach the height you want by adjustng the Center column Note Do not lock the column with too much force or it will damade the Screw thread Inside Reversible 3 8 or 14 mounting screw See figure 9 Your Benro tripod incorporates a reversible mounting Screw that accommodates any tripod head mounting thread 3 8 Or1 4 The tnpod is factory shipped in the 3 8 mounting thread exposed If is Decomes necessary to reverse the mounting Screw to the 1 4side loosen the locking nut Counter clockwise using the Included wrench untl it becomes 00se and unscrew the mounting Screw until it can be complete removed Reverse the Screw so that the 1 4hreads are in position and screw it back into place secure with the locking nut and wrench Please note Allow enough of the Screw threads to be avallable for maximum securily when the tripod head is mounted onto the tripod It s recommended that at least 5 to 6 threads be exposed for before locking the mounting screw in place MagicPod Fig 10 Fig 11 Fig 12 Fig 13 Center column foam grip shaft and strap can be assembled together to become a MagicPod Lock the column on the foam grip shaft in counter clockwise direction lock the two buckles of the strap to the positlon as Fig 12 then you can USe It Foam grip shaft and strap are not come with the tripod you need to Durchase them separately
Download Pdf Manuals
Related Search