HORSEMAN SWPシリーズ
Contents
1. Knob then raise or lower 2 RB the Front Frame Lens portion 2 Tighten the Rise Fall Locking Knob when the desired movement has been achieved Lateral Shift 1 1 Loosen the Lateral Shift 2 Locking Knob then move the Rear Frame Film Holder portion 2 Tighten the Lateral Shift Locking Knob when the desired movement has been achieved co each 35mm2. Owner s Manual SWE12P BACK Name of Parts Shift Locking Knob Shift Scale Spirit Levels Neck Strap Lugs Rise Fall Scale Rise Fall Locking Knob Rubber Grips Lens Unit Lock Screw Holes Tripod Socket Accessory Shoe Accessory Shoe Safety Lock Film Holder Lock SW6x9P Name of Parts Shift Locking Knob Shift Scale Spirit Levels Neck Strap Lugs Rise Fall Scale Rise Fall Locking Knob Rubber Grips Lens Unit Lock Screw Holes Tripod Socket Accessory Shoe Accessory Shoe Safe
3. 6X12cm 75mm 1mm 90mm 4mm Set the Mask for Lateral Shift with the allow towards the same direction that the lens is to be moved wiht theftwo round holes for spirit levelabservation at the top andthe bottom Shift the Rear Frame by 10mm CAUTION The direction of the movementis OPPOSITE with Lens and Back Therefore when you wish to shift the Lens LEFT you move the Rear Frame RIGHT and vice versa Pre Shift Finder Masks for 35mm and 45mm cover up to 6x9cm format while Masks for SW612P for 55mm and longer cover up to 6x12cm fomat 10mm Leateral Shift with 6x12cm format using a 75mm or 90mm Lens will cause slight vignetting approx 1mm with 75mm and apporox 4mm with 90mm SW612P SW6x9P Specifications SW612P SW6x9P TYPE Interchangeable Lens Film Holder Wide angle Camera with Vertical and Lateral Shift Movements FORMAT 6x12cm 6x9cm 6x7cm 6x9cm 6x7cm CAMERA MOVEMENTS 34mm 17mm 30mm 15mm Vertical Shift 34mm Rise 17mm Fall 17mm Lateral Shift 30mm 15mm L R each 34mm 17mm 40mm 20mm Vertical
4. Vertical Shift Lateral Shift Vertical Shift Lateral Shift Vertical Shift Lateral Shift 10mm SW SW612 21461 SW6x9 22551 SWP 21465 SWP 21463 10mm 45mm 55mm Movement potential is determined by the coverage of the lens used and the internal vignetting of the camera body please refer to the chart below This chart is based on typical specifications of the lens focused at infinity The limitations may vary Your own test would be highly recommended Maximum Displacements Pre Shifted Finder Masks which correspondto 10mm displacements rise foll or lateral shift are provided as optional accessories Use of an optional SW Ground Glass
5. Slide the Film Holder Lock to the right Detach the Film Holder from the camera back Attaching Slide the Film Holder Lock to the right Attach the Film Holder aligning the groove of the Film Holder onto the Film Holder Retainer Slide the Film Holder Lock tothe Left to lock Detaching Slide the Film Holder Lock to the right Detach the Film Holder from the camera back SW612P SW6x9P Rise Fall Lateral Shift Movements Rise Fall 1 1 Loosenthe Rise Fall Locking
6. Shift 34mm Rise 17mm Fall 17mm Lateral Shift 40mm 20mm L R each SPIRIT LEVELS DIMENSIONS 171 W 136 H X 133 D mm 3 3 for all dimentions 164 W 136 H X133 D mm WEIGHT SW 4 3 12 KOMAMURA CORPORATION 103 0013 3 2 4 TEL 03 3639 3351 FAX 03 3808 0116 www komamura co jp 1 77kg 1 83kg 45mm 45mm Lens Roll Film Holder and View Finder 1 Remove the Four Panel Locking Screws from the Lens Panel Turn the
7. Back 21461 for SW612P or Angle Viewer 22551 for SW6x9P is recommended when precise framing and or focusing is required Fall movement is unobtainable when the camera is directly mounted on a tripod Please use an optional SW Professional Tripod Base 21465 to use the fall movement on a tripod Fall movement is unobtainable when an optional SW Professional Lens Guard is fitted The Rise is limited to 10mm SW612P SW6x9P SW 10mm Using a Pre Shifted Finder Mask When using a Pre shifted Finder Mask always use displacement of just 10mm either direction A pre shifted Finder Mask Set consists of a mask for Rise Fall and a mask for Lateral Shift 1 1 Rise Set the Mask for Rise Fall with the allow towards the top and the two round holes for spirit level abservation
8. Screws counterclockwise 2 Insert the Nylon Washers attached to this manual between the Lens Panel and the Locking Screws ff you attach the SW Lens Unit without using the washers the ends of the Locking Screws may scratch the camera body when the Rise Fall movement is applied Three sets 12pieces of the washers are attach ed lfyou need more please ask your dealer HORSEMAN HORSEMAN is a registered tredemark of Komamura Corporation Tokyo Japan Specifications are subject to change without notice
9. at the top and the bottom Raise the front Frame by 10mm 2 2 Fall Set the Mask for Rise Fall with the allow towards the Bottom and the two round holes for spirit level abservation at the top and the bottom Drop the front Frame by 10mm 3 3 Lateral Shift 35mm 45mm 6x9cm SW612P 55mm 6x9cm 6x12cm 6x7cm 75mm 90mm 10mm
10. ty Lock Film Holder Catch Film Holder Lock Film Holder Retainer SWE12P SW6x9P Attaching Detaching the Film Holder Attaching Detaching the Film Holder Attaching Slide the Film Holder Lock to the right Attach the Film Holder aligning the groove of the Film Holder onto the Film Holder Retainer Slide the Film Holder Lock tothe Left to lock Detaching
Download Pdf Manuals
Related Search