Home

Centellis 4100 Getting Started Guide

1. 151 Centellis 4100 Getting Started 6806800E18B Installing the ATCA F120 Table 5 2 Critical Temperature Limits Temperature in Location Temperature in Celsius Fahrenheit Description 1 85 C 185 F Top center of DC DC converter used for management power 2 100 C 212 F PCB surface of main DC DC converter 3 105 C 221 F Big capacitor margin which faces the DC DC converter 4 90 C 194 F Top center of filter coil 5 3 2 Power Requirements Make sure that the blade is used in an AdvancedTCA shelf connected to 48VDC up to 60VDC according to Telecommunication Network Voltage TNV 2 A TNV 2 circuit is a circuit whose normal operating voltages exceed the limits for a safety extra low voltage SELV under normal operating conditions and which is not subject to overvoltages from telecommunication networks Table 5 3 DC System Power Requirements Feature Value Rated voltage 48VDC to 60VDC US and Canada 48VDC Operating voltage 40 0VDC to 72VDC US and Canada 40 0 to 60VDC Input current max 5 0A 40V Power dissipation max 200W The tested blade was a ATCA F120 blade including two installed AMC modules 35W each and an RTM ATCA F120 COP 30W 5 4 Configuring the Blade Their location is shown in the following figure The switch settings shown in the figure correspond to the de
2. 194 Centellis 4100 Getting Started 6806800E18B Installing the ATCA 7221 Before installing an PMC module observe the following notes N I P Only PMC modules based on 3 3V signaling level are supported e Toensure proper EMC shielding either operate the blade with a PMC module installed or with a blind panel e Ifthe blade is upgraded with a PMC module ensure that the blind panel is stored in a safe place in order to be reused again when removing the PMC module NOTICE Limited Power on PMC Modules and RTMs The blade does not provide an extra fuse for PMC modules and RTMs PMC modules and RTMs used together with the blade have to be qualified according to the following standards IEC 60950 1 EN 60950 1 UL 60950 1 CAN CSA C22 2 No 60950 1 PMC Module Malfunctioning Processor PMC modules as defined in ANSI VITA 32 2003 can be operated in two different modes monarch and non monarch mode Make sure to operate any installed processor PMC modules as defined in ANSI VITA 32 2003 only in non monarch mode Exceeding of Blade s Power Consumption Exceeding the maximum power dissipation of an installed PMC modules may damage the blade Make sure that the combined power dissipation of an installed PMC module on the 3 3V and 5V rail does not exceed 7 5W Installation Procedure To install a PMC module proceed as follows 1 Mount t
3. Procedure Tool Document Chapter ATCA A100 firmware upgrade FUMI System Management Interface Based on HPI B Centellis 31kX 4100 User s Guide Chapter Using the Firmware Update Management Instrument fw_tool ATCA M100 Installation and Use Chapter Software Upgrade ATCA F120 firmware upgrade FCU Basic Blade Services Software on ATCA F120 Programmer s Reference Chapter Firmware Upgrade Facility fw_tool ATCA M100 Installation and Use Chapter Software Upgrade ATCA M100 firmware upgrade FUMI System Management Interface Based on HPI B Centellis 31kX 4100 User s Guide Chapter Using the Firmware Update Management Instrument fw_tool ATCA M100 Installation and Use Chapter Software Upgrade ATCA M100 payload upgrade FUMI System Management Interface Based on HPI B Centellis 31kX 4100 User s Guide Chapter Using the Firmware Update Management Instrument swupgr ATCA M100 Installation and Use ade Chapter Software Upgrade BBS software upgrade on any Install the files of the new software version as described blade in the Basic Blade Services Software Programmer s Reference of the respective blade Chapter Installation Blower firmware upgrade FUMI System Management Interface Based on HPI B Centellis 31kX 4100 User s Guide Chapter Using the Firmware Update Management Instrument fw_tool ATCA M100 Installation and Use Chapter Software Upgrade
4. 0 00 cece eee eee eee eee sonne 169 Table 6 1 Environmental Requirements cece eee e eee eee teen een ee een nennen nen 169 Table 7 1 Environmental Requirements 0 sce e cece e eee e nent n tenet nee eees 176 Table 7 2 Critical Temperature Limits 00 cece cece eee een teen nent nen ee ees 177 Table 8 1 Environmental Requirements 0 sce e cece cence eee ene eee e eee eeneeaees 185 Table 8 2 Critical Temperature Limits 2 cece e cece eee eee tenet beeen nun sonne 186 Table 8 3 Power Requirements 0c cece cece cece eee teen eee eee een teeta ene eenees 188 Table 8 4 Switch Settings u ee an 191 Table 10 1 Software Available on System Components eee eee cent eee eee eeeeeaee 207 Table 10 2 Available Software Upgrade Tools 0c cece eee ene e eee nee e ee nennen 209 Table A 1 Artesyn Embedded Technologies Embedded Computing Publications 213 Table A 2 Manufacturer s Documents ae eine 214 Table A 3 Related Specifications 2 cece cece een n ene nennen nee nennen 215 Centellis 4100 Getting Started 6806800E1 8B 9 List of Tables eee EEE 10 Centellis 4100 Getting Started 6806800E18B List of Figures NL Figure 1 1 Systemi Front VIEW ee een 111 Figure 1 2 System Rear View en 112 Figure 1 3 SIOE Distribution uns nn ee nr E EEEE ETE 114 Figure 2 1 Hot Spot Air Inlet cece cece eee c cence eee eee e ete eeeeeneees 122
5. 210 Centellis 4100 Getting Started 6806800E18B System Software Table 10 2 Available Software Upgrade Tools continued Procedure Tool Document Chapter ATCA 7221 firmware upgrade FUMI System Management Interface Based on HPI B Centellis 31kX 4100 User s Guide Chapter Using the Firmware Update Management Instrument FCU Basic Blade Services Programmer s Guide of the respective blade Chapter Firmware Upgrade Facility PEM IPMI firmware upgrade FUMI System Management Interface Based on HPI B Centellis 31kX 4100 User s Guide Chapter Using the Firmware Update Management Instrument fw_tool ATCA M100 Installation and Use Chapter Software Upgrade Please refer to the Release Notes to find out about software dependencies Centellis 4100 Getting Started 6806800E18B 211 System Software ee SER DES an nn 212 Centellis 4100 Getting Started 6806800E18B Appendix A Related Documentation SS a eS A 1 Artesyn Embedded Technologies Embedded Computing Documentation The publications listed below are referenced in this manual You can obtain electronic copies of Artesyn Embedded Technologies Embedded Computing publications by contacting your local Artesyn sales office For released products you can also visit our Web site for the latest copies of our product documentation 1 2 3 4 Go to www artesyn com computing Under SUPPORT click TECHNICAL DOCUMENTATION U
6. 146 Centellis 4100 Getting Started 6806800E18B Installing the ATCA F120 5 1 Overview This chapter describes how to install the ATCA F120 into the system These main steps and their sequence are 1 Unpack and inspect the blade Make sure environmental and power requirements are met Configure the Centellis 4100 Install the Centellis 4100 oe ow LN If applicable install AMC modules vty Ifthe ATCA F120 is already preinstalled in your system configuration you can disregard the NN following sections 5 2 Unpacking and Inspecting the Blade NOTICE Damage of Circuits Electrostatic discharge and incorrect installation and removal of the blade can damage circuits or shorten their life Before touching the blade or electronic components make sure that your are working in an ESD safe environment Centellis 4100 Getting Started 6806800E18B 147 Installing the ATCA F120 5 3 5 3 1 148 Shipment Inspection To inspect the shipment perform the following steps 1 Verify that you have received all items of your shipment 2 Check for damage and report any damage or differences to the customer service 3 Remove the desiccant bag shipped together with the blade and dispose of it according to your country s legislation The blade is thoroughly inspected before shipment If any damage occurred during transportation or any items are missing please contact our customer s service immediately Environmen
7. When operating the blade in areas of electromagnetic radiation ensure that the blade is bolted on the system and the system is shielded by enclosure Centellis 4100 Getting Started 6806800E1 8B 83 ATCA 7221 Safety Notes Injuries or Short Circuits Blade or power supply In case the ORing diodes of the blade fail the blade may trigger a short circuit between input line A and input line B so that line A remains powered even if it is disconnected from the power supply circuit and vice versa To avoid damage or injuries always check that there is no more voltage on the line that has been disconnected before continuing your work Switch Settings Blade Malfunction Switches marked as reserved might carry production related functions and can cause the blade to malfunction if their setting is changed Therefore do not change settings of switches marked as reserved The setting of switches which are not marked as reserved has to be checked and changed before blade installation Blade Damage Setting resetting the switches during operation can cause blade damage Therefore check and change switch settings before you install the blade PMC Modules 84 Limited Power on PMC Modules and RTMs The blade does not provide an extra fuse for PMC modules and RTMs PMC modules and RTMs used together with the blade have to be qualified according to the following standards IEC 60950 1 EN 60950 1 UL 60950 1 CAN CSA C22 2 No 60950 1
8. All system components are delivered with the software installed Centellis 4100 Getting Started 6806800E18B System Software In case you need to reinstall the software on the ATCA F120 an AMC module or a node blade you need to install the Basic Blade Services BBS Software as described in the respective Basic Blade Services Software Programmer s Reference The BBS installation automatically installs all necessary files BBS images must be installed on hard disks or for node blades and AMC modules the ATCA F120 must have a boot image for the respective blade or AMC module 10 5 Upgrade The procedures and tools for software upgrades differ depending on what component needs to be upgraded Available tools for firmware upgrades are e FCU part of BBS e FUMI part of HPI B e fw_tool integrated in the ATCA M100 root file system e swupgrade integrated in the ATCA M100 root file system The following table shows which tools you can use and where you can find a description of how to do it S N gt Artesyn recommends to always use FUMI if available Table 10 2 Available Software Upgrade Tools Procedure AMC module firmware upgrade Tool FCU Document Chapter Basic Blade Services Programmer s Guide ofthe respective module Chapter Firmware Upgrade Facility Centellis 4100 Getting Started 6806800E18B 209 System Software Table 10 2 Available Software Upgrade Tools continued
9. SCSI Definition Small Computer System Interface SELV ShM Safety Extra Low Voltage Shelf Manager ShMC Shelf Management Controller SSH Secure Shell TDM Time Division Multiplexing TNV 2 Telecom Network Voltages without overvoltage TPE UL Twisted Pair Ethernet Underwriters Laboratories VCCI Voluntary Control Council for Interference Conventions Notation 0x00000000 Description Typical notation for hexadecimal numbers digits 0 through F e g used for addresses and offsets 0b0000 Same for binary numbers digits are 0 and 1 X Generic use of a letter n Generic use of numbers 0 75 Bold Decimal number Used to emphasize a word Courier Used for on screen output Courier Bold Used to characterize user input Italics Used for references table and figure descriptions File gt Exit Notation for selecting a submenu lt text gt text Centellis 4100 Getting Started 6806800E1 8B Notation for variables and keys Notation for buttons and optional parameters 15 About this Manual Notation Description Repeated item example A1 A2 A3 A12 Omission of information from example command that is not necessary at the time being Ranges e g 0 4 means one of the integers 0 1 2 3 and 4 used in register description tables Logical OR
10. e Das System darf ber die TPE Stecker nur mit einem Sicherheits Kleinspannungs Stromkreis SELV verbunden werden e Bei Fragen wenden Sie sich an Ihren Systemverwalter 42 Centellis 4100 Getting Started 6806800E18B Centellis 4100 Shelf Sicherheitshinweise Laser Verletzungsgefahr Einige Boards die in verschiedenen Systemkonfigurationen verwendet werden sind Laserprodukte der Klasse 1 Verwenden Sie diese anders als in der Dokumentation beschreiben kann dies zu gef hrlicher Strahlung f hren Einge RTMs sind Laserprodukte der Klasse 1 Verwenden Sie diese anders als in der Dokumentation beschreiben kann dies zu gef hrlicher Strahlung f hren Batterieaustausch Besch digung der Boards Ein unsachgem er Austausch von Batterien kann zu gef hrlichen Explosionen und Besch digung der Boards f hren Verwenden Sie deshalb nur den Batterietyp der auch bereits eingesetzt wurde und befolgen Sie die entsprechende Anleitung im Installationshandbuch des jeweiligen Boards Entsorgen sie alte Batterien entsprechend der in Ihrem Land g ltigen Richtlinien Umweltschutz Umweltschutz Entsorgen Sie alte Blades RTMs und Systeme gem derin Ihrem Land g ltigen Gesetzgebung und den Empfehlungen des Herstellers Centellis 4100 Getting Started 6806800E18B 43 Centellis 4100 Shelf Sicherheitshinweise eee EEE 44 Centellis 4100 Getting Started 6806800E18B ATCA M100 Safety Notes EMC This section provides warn
11. A KERKKRKICHR III ICHR I ICHRIICHOR KICKER ICKER IKK IOKKILICK EICH KAXAXKKAAXKAAHXKAAXKAAHKKAAXKAAXKAKAXKAAXKAAXKAKAXKAH AKKAXXKAAXKAAKKAAKKAAKKAAKKAAKKAAKKAAKKAAKKAAKKKA Indicates a hazardous situation which if not avoided could result in death or serious injury KXKXXXKAXKKXXKKXKKKXKKKXKKAXKKXXKKXXKKXXKKXKKXXKK JOO OOOO OOOO OI INK IHK IH KAAAKK AAK KAAKA MEN IL OO NL AAK LEN DENN NN EMI AKK Indicates a hazardous situation which if not avoided may result in minor or moderate injury KXXKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKXKK INK KXXXXKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKK KK XXI KXXXKKKXKXKKKKKKKKKKKKKKKKKKIKKKKKKKKKKKKKKKKKK XXX Indicates a property damage message i u i 2000000000000000000000000000000000000000000000XXXX AAXKXXAXXAXXXKXAXKXAXAKXKXKXKXKXXXAKKKXKAKXKXKXKXKKK No danger encountered Pay attention to important information Summary of Changes Order No Date Description 6806800E18A March 2008 First version 6806800E18B September 2014 Re branded to Artesyn template 16 Centellis 4100 Getting Started 6806800E1 8B Centellis 4100 Shelf Safety Notes ee This section provides warnings that precede potentially dangerous procedures throughout this manual Instructions contained in the warnings must be followed during all phases of operation service and repair of this equipment You should also employ all other safety precautions necessary for
12. Consult your local Artesyn sales representative if in doubt Limitation of Operating Temperature Range Installing AMC modules with small operating temperature ranges into the ATCA F120 may further restrict the operating temperature range of the ATCA F120 Make sure that the operating temperature of any installed AMC modules and the ATCA F120 as a bundle are within allowed limits Poor Shelf Cooling and EMC Compliance Violation An empty AMC bay may result in poor shelf cooling and strong EMC radiation and thus lead to EMC compliance violation Therefore always cover empty or unused AMC bays with a filler panel Installation Procedure The following describes how to install an AMC module into AMC bay B1 and B4 1 Make sure you are in an ESD safe environment 2 Identify the AMC bay to be used for the installation Centellis 4100 Getting Started 6806800E18B 165 Installing the ATCA F120 Refer to Supported AMC Modules on page 161 for more details 3 If the required AMC bay is occupied by an AMC filler panel you will need to remove the filler panel before proceeding with the installation procedure The removal procedure for the filler panel is the same as described in the Removal procedure which follows immediately after this procedure Ignore steps that mention the blue LED 4 Ensure that the AMC module handle is in the extracted position pulled outward away from the face plate 5 Using yourthumb apply equal an
13. Fat Pipes Olo NI Ds wo BI WwW N Fabric Channel switch 2 port 19 Fabric Channel Switch 2 Port 20 Fabric Channel Switch 2 Port 16 SERDES 1000BaseT on ATCA F120 face plate 13 Unused 14 Unused 15 Unused oO _ Extended Option _ N Centellis 4100 Getting Started 6806800E18B 163 Installing the ATCA F120 Table 5 6 AMC Bay B1 Port Assignments continued Connector Region AMC Port Usage on ATCA F120 16 Differential telecom clock to and from the AMC 17 Unused 18 Unused 19 Unused 20 Unused 164 Centellis 4100 Getting Started 6806800E18B Installing the ATCA F120 5 6 2 AMC Module Installation This section describes how to install and remove an AMC module NOTICE Damage of Circuits Electrostatic discharge and incorrect installation and removal of the blade can damage circuits or shorten their life Before touching the blade or electronic components make sure that your are working in an ESD safe environment AMC Module Damage The two AMC bays only support AMC types modules which are officially supported by Artesyn AMC modules installed into AMC bay 1 or 4 must not exceed a power dissipation of 35W Installing and operating other AMC modules may damage the AMC modules the blade and an installed RTM including attached devices Only install AMC modules into AMC bay B1 and B4 which are officially supported by Artesyn
14. PMC Module Malfunctioning Processor PMC modules as defined in ANSI VITA 32 2003 can be operated in two different modes monarch and non monarch mode Make sure to operate any installed processor PMC modules as defined in ANSI VITA 32 2003 only in non monarch mode Centellis 4100 Getting Started 6806800E1 8B ATCA 7221 Safety Notes Exceeding of Blade s Power Consumption Exceeding the maximum power dissipation of an installed PMC modules may damage the blade Make sure that the combined power dissipation of an installed PMC module on the 3 3V and 5V rail does not exceed 7 5W Battery Blade Damage Wrong battery installation may result in hazardous explosion and blade damage Therefore always use the same type of Lithium battery as is installed and make sure the battery is installed as described in this manual Environment Always dispose of used blades system components and RTMs according to your country s legislation and manufacturer s instructions Centellis 4100 Getting Started 6806800E1 8B 85 ATCA 7221 Safety Notes eee EEE 86 Centellis 4100 Getting Started 6806800E18B ATCA 7221 Sicherheitshinweise ee EMV Dieses Kapitel enth lt Hinweise die potentiell gef hrlichen Prozeduren innerhalb dieses Handbuchs vorrangestellt sind Beachten Sie unbedingt in allen Phasen des Betriebs der Wartung und der Reparatur des Systems die Anweisungen die diesen Hinweisen enthalten sind Sie sollten au erdem al
15. Tempe Arizona 85282 Germany Contents LL S s _ i wme i i i ti i i i sS About this Manual sun na 13 Centellis4100 Shelf Safety Notes 0 un se secee see seiessaeeeees 17 Centellis 4100 Shelf Sicherheitshinweise 0 cece ccc cece eee eee e cence eeeeeeeee 31 ATCA M100 Safety Notes o 5ccccsccc00sc0ccsccosses 000000000 na 0 0a nn asasi s 45 ATCA M100 Sicherheitshinweise u un ec es a a eae 51 SPARE ATCA A100 Safety Notes 2 ne ee 57 SPAREJATCA A100 Sicherheitshinweise ce cece cece cece cere nee ee cece nennen en une 59 ATCA F120 Safety Notes u a u 61 ATCA F120 Sicherheitshinweise ossssssseeeeesssssnnsnnnnnnsssnne nennen nennen 67 RIM ATCA F 120C Safety NOLES ann een 73 RTM ATCA F120C Sicherheitshinweise cece cece cece cece cece cence eee nennen nenn 77 ATCA 7 221 Satety Notes se na anaE REEE 81 ATCA 7221 Sicherheitshinweise u 000 2000 10000000 0000000 000 100 0 0 as 87 RTM ATCA 7221 FC Safety Notes an se 93 RTM ATCA 7221 FC Sicherheitshinweise ccc cece cece cece cece e eee eeeceeeeeeeees 97 RTM ATCA 7221 SCS Safety Notes iu tose eet iebeenesssseseaseeeweas taeda 101 Centellis 4100 Getting Started 6806800E18B 3 RTM ATCA 7221 SCS Sicherheitshinweise ccce cece cece cece cece eee e ese eeeenes 105 WRYOGUCHON 46033552028 505 Gores chen eaea ipasea a edeae SS SO50008 640055 89RE5 109 1 1 OVEIMIOW re en
16. normal 40 C 40 F to 70 C 158 F operation according to NEBS Standard GR 63 may be further limited by installed CORE accessories 5 C 23 F to 55 C 131 F exceptional operation according to NEBS Standard GR 63 CORE All values may be further limited by installed accessories with more restrictive environmental requirements Temp 0 25 C min according to NEBS Standard GR 0 25 C min Change 63 CORE Rel Humidity 5 to 95 non condensing according to 5 to 95 non condensing Artesyn internal environmental requirements according to Artesyn internal environmental requirements Altitude Up to 3 000 m Up to 12 000 m Vibration 5 20 Hz 0 5 mm amplitude 1 mm amplitude 20 250 Hz 1g 2 0g Shock 5 g 11 ms halfsine according to Artesyn 15 g 11 ms half sine according to internal environmental requirements Artesyn internal environmental requirements Free Fall 1 200 mm all edges and corners To guarantee proper RTM operation you have to make sure that the temperature at the following location is not exceeded Table 6 2 Critical Temperature Limits Location Component Temperature Limit 1 Installed hard disk 60 C 140 F normal operation 90 C 194 F maximum temperature with decreased warranty lifetime 2 TX1322 TLV 1 transformer 80 C 176 F 3 TX1322 TLV 1 transformer 80 C 176 F Centellis 4100 Getting Started 6806800E18B 169 Installing the RTM ATCA
17. 8 3 Switch Settings The blade provides the configuration switches SW1 SW2 SW3 SW4 and SW12 Their location is shown in the figure below Centellis 4100 Getting Started 6806800E18B 189 Installing the ATCA 7221 Figure 8 2 Location of On Board Switches i ELLI NN HY VO MAW Slat AANA TAS OVA Nea WAAAY N o CAL At wa TIER N X N IN N wel mmi a 190 Centellis 4100 Getting Started 6806800E18B Installing the ATCA 7221 Blade Malfunction Switches marked as reserved might carry production related functions and can cause the blade to malfunction if their setting is changed Therefore do not change settings of switches marked as reserved The setting of switches which are not marked as reserved has to be checked and changed before blade installation Blade Damage Setting resetting the switches during operation can cause blade damage Therefore check and change switch settings before you install the blade Table 8 4 Switch Settings Switch Description SW1 1 Backup boot flash boot block write protection OFF Write protected ON Write enabled default SW1 2 Backup boot flash data instruction block write protection OFF Write protected ON Write enabled default SW1 3
18. Centellis 4100 Getting Started 6806800E18B 105 RTM ATCA 7221 SCS Sicherheitshinweise Das Produkt arbeitet im Hochfrequenzbereich und erzeugt St rstrahlung Bei unsachgem em Einbau und anderem als in diesem Handbuch beschriebenen Betrieb k nnen St rungen im Hochfrequenzbereich auftreten Warnung Dies ist eine Einrichtung der Klasse A Diese Einrichtung kann im Wohnbereich Funkst rungen verursachen In diesem Fall kann vom Betreiber verlangt werden angemessene Ma nahmen durchzuf hren 106 Centellis 4100 Getting Started 6806800E18B RTM ATCA 7221 SCS Sicherheitshinweise Installation Betrieb Besch digung von Schaltkreisen Elektrostatische Entladung und unsachgem er Ein und Ausbau von Blades kann Schaltkreise besch digen oder ihre Lebensdauer verk rzen Bevor Sie Blades oder elektronische Komponenten ber hren vergewissern Sie sich dass Sie in einem ESD gesch tzten Bereich arbeiten Besch digung des Produktes Fehlerhafte Installation des Produktes kann zu einer Besch digung des Produktes f hren Verwenden Sie die Handles um das Produkt zu installieren deinstallieren Auf diese Weise vermeiden Sie dass das Front Panel oder die Platine deformiert oder zerst rt wird Besch digung des RTMs Wenn Sie das RTM nicht zusammen mit dem ATCA 7221 Front Blade installieren wird das RTM besch digt Installieren Sie das RTM deshalb nur zusammen mit dem Artesyn ATCA 7221 Front Blade Datenverlust Wenn Sie das
19. Figure 2 2 HotSpot Air Outlet na aan ee a Eii 123 Figure 2 3 Hot Spot Power Entry Module ccc cece cece e eee eee n eee ennees 124 Figure 2 4 Rack Mounting Dimensions 0 eee e eee eee nent rennen nen 128 Figure 2 5 Shelf Airtlow u ae en mn saga diese Dina 129 Figure 2 6 Planning Checklist 1 2 0 cece eee cece een ene n ene eeeeneees 131 Figure 2 7 Planning Checklist 2 4 2 04 ea ete atnaede neii ee bae ed ease ae 132 Figure 3 1 Rack Mounting Dimensions 0 eee e eee eee e eee nee nennen nen 138 Figure 3 2 Grounding Lugs at the System s Rear 0 cece cece eee eee eee ee eens 139 Figure 5 1 Critical Temperature Spots 00 c cece cece een eee tenet ene nenne 151 Figure 5 2 On Board Configuration Switches 0 cece eee cece eee ene e eee e eee 153 Figure 5 3 Location Of AMC BayS 2 cece cece eee nent eee nennen nennen nenne 160 Figure 5 4 AMC Module B4 Interconnection Scheme eee ee eee ee eee eee eee 162 Figure 6 1 Critical Temperature Spot 0 cece cece cece nce nent een ee een en nnn 170 Figure 7 1 Critical Temperature Spots 0 ccc cece cece ete nee e nent een een 178 Figure 8 1 Location of Critical Blade Temperature Spots Blade Top Side 187 Figure 8 2 Location of On Board Switches ec cece cence eee teen een e tees 190 Figure 8 3 Location of PMC Slot 0 2 0 eee eee eee nen eee ededi kane ai ea 194 Centellis 410
20. Node Blade 13119 7 5 3 1 2 4 6 8 10 12 14 Logical Slots The node slots can be equipped with AdvancedTCA blades Artesyn provides the ATCA 7221 a high performance single slot hot swappable node blade 1 2 5 Hub Slots The hub slots are usually equipped with ATCA F1 20 switches This blade combines standard PICMG 3 0 base interface and PICMG 3 1 fabric interface 10Gb Ethernet switching and optionally provides a Time Division Multiplexing TDM clock generator for clock synchronization of line cards and other shelves 1 2 6 Rear Transition Modules The AdvancedTCA blades can be connected to Rear Transition Modules RTM to provide easy access to I O signals through the zone 3 connector defined by the AdvancedTCA specification 114 Centellis 4100 Getting Started 6806800E18B Introduction 1 2 7 1 2 8 1 2 9 1 2 10 The Artesyn RTMs can be used as rear expansion boards for node blades and for the switch to access the different interfaces on an AdvancedTCA blade through the RTM face plate AMC Modules AMC modules can be mounted on carrier cards Power Entry Modules Four field hot swappable intelligent PEMs with a 50A breaker and line filter are installed beneath the rear slots of the backplane The four PEMs are used to provide split redundant power Blowers The system provides fault tolerant cooling by using four front accessible hot swappable intelligent blower trays Each blower tray contains one blower w
21. Stellen Sie vor dem Einschalten des Stroms sicher dass sich auf dem Board kein Kondensat befindet Centellis 4100 Getting Started 6806800E18B 53 ATCA M100 Sicherheitshinweise berhitzung und Besch digung des Boards Betreiben Sie das Board ohne Zwangsbel ftung kann das Board berhitzt und schlie lich besch digt werden Bevor Sie das Board betreiben m ssen Sie sicher stellen dass das Shelf ber eine Zwangsk hlung verf gt Verletzungen oder Kurzschl sse Board oder Stromversorgung Falls die ORing Dioden des Boards durchbrennen kann das Board einen Kurzschluss zwischen den Eingangsleitungen A und B verursachen In diesem Fall ist Leitung A immer noch unter Spannung auch wenn sie vom Versorgungskreislauf getrennt ist und umgekehrt Pr fen Sie deshalb immer ob die Leitung spannungsfrei ist bevor Sie Ihre Arbeit fortsetzen um Sch den oder Verletzungen zu vermeiden Hot Swap Wenn Sie das Board im laufenden Betrieb in ein System das weder Hot Swap noch High Availability unterst tzt installieren bzw herausziehen wird das Board besch digt und es gehen Daten verloren Installieren entfernen Sie das Board nur im laufenden Betrieb wenn das System Hot Swap oder High Availability unterst tzt und wenn die Systembeschreibung dies ausdr cklich erlaubt RJ 45 Stecker Der RJ 45 Stecker auf der Frontblende darf nur f r Twisted Pair Ethernet TPE Verbindungen verwendet werden Beachten Sie dass ein versehentliches A
22. me circuit d alimentation c c doivent tre install s a proximit les uns des autres p ex dans des armoires adjacentes et a proximite de la prise de terre du circuit d alimentation c c Le circuit d alimentation c c ne doit comporter aucune autre prise de terre La source d alimentation du circuit c c doit tre situ e dans la m me pi ce que le mat riel Il ne doit y avoir aucun dispositif de commutation ou de sectionnement entre le point de raccordement au conducteur de la source d alimentation c c et le point de raccordement la prise de terre Centellis 4100 Getting Started 6806800E1 8B Centellis 4100 Shelf Safety Notes System Overheating If you reduce the blower speed the system temperature will rise Constantly control the system temperature once you have reduced the blower speed While operating the system ensure that the environmental and power requirements are met Loss of Safety Approval for ATCA 715 7105 717 7107 and the System If you use the ACC CABLE RJ45 DSUB in applications other than maintenance and if you use it with devices not providing a protection according to EN 60950 1 you loose the safety approval of the blade Therefore only use the ACC CABLE RJ45 DSUB for maintenance and with devices providing a protection according to EN 60950 1 Injuries or Short Circuits Blade or Power Supply In case the ORing diodes of the blade fail the blade may trigger a short circuit between input line A and in
23. 7221 FC Critical Temperature Spot Figure 6 1 Centellis 4100 Getting Started 6806800E18B 170 Installing the RTM ATCA 7221 FC 6 2 Module Installation The RTM must be installed into a AdvancedTCA system without a zone 3 midplane NOTICE RTM Damage Installing the RTM with other blades than the Centellis 4100 may damage the RTM and the front blade Only install the RTM with the Artesyn Centellis 4100 blade Damage of Circuits Electrostatic discharge and incorrect RTM installation and removal can damage circuits or shorten their life Before touching the RTM or electronic components make sure that you are working in an ESD safe environment Centellis 4100 Getting Started 6806800E18B 171 Installing the RTM ATCA 7221 FC 6 2 1 Installing the RTM Installation Procedure Follow the following steps to install the RTM 1 Locate the slot the RTM is to be installed into the shelf s rear which must be the same as that of the front blade 2 Ensure that the top and the bottom handles of the RTM are in an outward position by squeezing the lever and the latch together 3 Insert the RTM into the shelf by placing the top and bottom edges in the card guides of the slot 4 Slide the RTM into the slot 5 Apply equal and steady pressure to the RTM to carefully slide the RTM into the shelf until you feel resistance Continue to gently push the RTM until the RTM connectors engage 6 Squeeze the l
24. Betriebs der Wartung und der Reparatur des Systems die Anweisungen die diesen Hinweisen enthalten sind Sie sollten au erdem alle anderen Vorsichtsma nahmen treffen die f r den Betrieb des Produktes innerhalb Ihrer Betriebsumgebung notwendig sind Wenn Sie diese Vorsichtsma nahmen oder Sicherheitshinweise die an anderer Stelle diese Handbuchs enthalten sind nicht beachten kann das Verletzungen oder Sch den am Produkt zur Folge haben Artesyn ist darauf bedacht alle notwendigen Informationen zum Einbau und zum Umgang mit dem Produkt in diesem Handbuch bereit zu stellen Da es sich jedoch um ein komplexes Produkt mit vielf ltigen Einsatzm glichkeiten handelt k nnen wir die Vollst ndigkeit der im Handbuch enthaltenen Informationen nicht garantieren Falls Sie weitere Informationen ben tigen sollten wenden Sie sich bitte an die f r Sie zust ndige Gesch ftsstelle von Artesyn Das System erf llt die f r die Industrie geforderten Sicherheitsvorschriften und darf ausschlie lich f r Anwendungen in der Telekommunikationsindustrie und im Zusammenhang mit Industriesteuerungen verwendet werden Einbau Wartung und Betrieb d rfen nur von durch Artesyn ausgebildetem oder im Bereich Elektronik oder Elektrotechnik qualifiziertem Personal durchgef hrt werden Die in diesem Handbuch enthaltenen Informationen dienen ausschlie lich dazu das Wissen von Fachpersonal zu erg nzen k nnen dieses jedoch nicht ersetzen Halten Sie sich von str
25. C 131 F exceptional operation according to NEBS standard GR 63 CORE Temp 0 25 C min 0 25 C min change according to NEBS standard GR 63 CORE Relative 5 to 90 non condensing 5 to 95 non condensing humidity according to Artesyn internal environmental according to Artesyn internal requirements environmental requirements Shock Half sine 11 ms 30 m s Blade level packaging Half sine 6 ms at 180 m s Centellis 4100 Getting Started 6806800E18B 119 Site Preparation Table 2 1 Environmental Conditions continued Feature Operating Non Operating packed state Vibration 0 1g from 5 Hz to 100 Hz and back to 5 Hzat 5 20 Hz at 0 01 g Hz tested in a rate of 0 1 octave minute 20 200 Hz at 3 0 dB octave target 213 platform Random 5 20 Hz at Im s Random 20 200 Hz at 3 dB octave Free fall 300mm 11 8 in packaged 25mm 1 in unpackaged per GR 63 CORE fully populated system Noise ETSI ETS 300 753 October 1997 Telecommunication equipment rooms attended 7 2 bel Measurement of declared A weight sound power level All values are applicable to normal operating conditions 23 C NEBS GR 63 CORE Issue 3 Telecommunication equipment rooms attended 78 dB Measurement of declared A weight sound power level All values are applicable to normal operating conditions 27 C e The ambient temperature is defined as the air inlet tempe
26. Halten Sie sich von stromf hrenden Leitungen innerhalb des Produktes fern Entfernen Sie auf keinen Fall Abdeckungen am Produkt Nur werksseitig zugelassenes Wartungspersonal oder anderweitig qualifiziertes Wartungspersonal darf Abdeckungen entfernen um Komponenten zu ersetzen oder andere Anpassungen vorzunehmen Installieren Sie keine Ersatzteile oder f hren Sie keine unerlaubten Ver nderungen am Produkt durch sonst verf llt die Garantie Wenden Sie sich f r Wartung oder Reparatur bitte an die f r Sie zust ndige Gesch ftsstelle von Artesyn So stellen Sie sicher dass alle sicherheitsrelevanten Aspekte beachtet werden Centellis 4100 Getting Started 6806800E18B 51 ATCA M100 Sicherheitshinweise EMV Das Produkt wurde in einem Artesyn Standardsystem getestet Es erf llt die f r digitale Ger te der Klasse A g ltigen Grenzwerte in einem solchen System gem den FCCRichtlinien Abschnitt 15 bzw EN 55022 Klasse A Diese Grenzwerte sollen einen angemessenen Schutz vor St rstrahlung beim Betrieb des Produktes in Gewerbe sowie Industriegebieten gew hrleisten Das Produkt arbeitet im Hochfrequenzbereich und erzeugt St rstrahlung Bei unsachgem em Einbau und anderem als in diesem Handbuch beschriebenen Betrieb k nnen St rungen im Hochfrequenzbereich auftreten Wird das Produkt in einem Wohngebiet betrieben so kann dies mit gro er Wahrscheinlichkeit zu starken St rungen f hren welche dann auf Kosten des Produktanwenders b
27. Notes ee This section provides warnings that precede potentially dangerous procedures throughout this manual Instructions contained in the warnings must be followed during all phases of operation service and repair of this equipment You should also employ all other safety precautions necessary for the operation of the equipment in your operating environment Failure to comply with these precautions or with specific warnings elsewhere in this manual could result in personal injury or damage to the equipment Artesyn intends to provide all necessary information to install and handle the product in this manual Because of the complexity of this product and its various uses we do not guarantee that the given information is complete If you need additional information ask your Artesyn representative The product has been designed to meet the standard industrial safety requirements It must not be used except in its specific area of office telecommunication industry and industrial control Only personnel trained by Artesyn or persons qualified in electronics or electrical engineering are authorized to install remove or maintain the product The information given in this manual is meant to complete the knowledge of a specialist and must not be used as replacement for qualified personnel Keep away from live circuits inside the equipment Operating personnel must not remove equipment covers Only Factory Authorized Service Personnel or other qua
28. PMC Module und RTMs PMC Module und RTMs die zusammen mit dem Blade eingesetzt werden muessen gemaess den folgenden Standards qualifiziert sein IEC 60950 1 EN 60950 1 UL 60950 1 CAN CSA C22 2 No 60950 1 Fehlfunktion von PMC Modulen Prozessor PMC Module ANSI VITA 32 2003 koennen generell in zwei Modi betrieben werden Monarch und Nonmonarch Modus Centellis 4100 Getting Started 6806800E1 8B 91 ATCA 7221 Sicherheitshinweise Betreiben Sie auf dem Blade installierte PMC Module ANSI VITA 32 2003 nur im Nonmonarch Modus Ueberschreitung der zulaessigen Leistungsaufnahme des Blades Wird die maximal zulaessige Leistungsaufnahme eines installierten PMC Modules ueberschritten so kann dies zu einer Beschaedigung des Blades fuehren Stellen Sie sicher dass die Leistungsaufnahme eines installierten PMC Modules zusammen auf der 3 3V und 5V Schiene insgesamt 7 5W nicht ueberschreitet Batterie Besch digung des Blades Ein unsachgem er Einbau der Batterie kann gef hrliche Explosionen und Besch digungen des Blades zur Folge haben Verwenden Sie deshalb nur den Batterietyp der auch bereits eingesetzt wurde und befolgen Sie die Installationsanleitung Umweltschutz Entsorgen Sie alte Batterien und oder Blades Systemkomponenten RTMs stets gem der in Ihrem Land g ltigen Gesetzgebung und den Empfehlungen des Herstellers 92 Centellis 4100 Getting Started 6806800E18B RTM ATCA 7221 FC Safety Notes ee This section
29. Personal Injury PEMs will get hot Touching a hot PEM can cause injuries Let the PEM cool down before pulling it out with bare hands Start Up Procedure Depending on the system configuration the actual powering up may take up to 10 minutes 1 Put on an ESD wrist strap 2 Connect the strap to the shelf by attaching the front or rear ESD jack 3 Make sure that the system has been located in a place with room temperature for at least 24 hours before powering it up 4 Ensure that the breaker is in the OFF tripped position the red portion is visible on the top of the breaker If the breaker is not in the OFF position trip the breaker to the OFF position Centellis 4100 Getting Started 6806800E18B 199 Starting up the System 200 Remove the M6 nuts lockwashers and spring rings from each of the connections on the PEM and set aside Ensure that the power feeds you plan to remove or attach are powered off and cannot be switched on while you are working Attach the rubber boots to the feed cables with the two hole lugs If you want to connect chassis ground and 48VDC return you need to connect a cable from the PEM connections to the chassis grounding lugs Centellis 4100 Getting Started 6806800E18B Starting up the System 9 Install the feed cables to the connections on the PEM with the M6 nuts lockwashers and spring rings previously removed Torque nuts to 7 1 Nm 63 Ibf in 10 P
30. Programmer s Reference ATCA F120 Control via IPMI Programmer s Reference RTM ATCA F120C Control via IPMI Programmer s Reference Centellis 4100 Getting Started 6806800E18B 207 System Software 10 3 10 4 208 Table 10 1 Software Available on System Components continued Component Software Where to Find More Information ATCA M100 IPMC firmware ATCA M100 Control via IPMI Boot loader Uboot Programmer s Reference Linux kernel System Management Interface Based Initial ram disk on HPI B Centellis CO 31kX 4100 User s Guide system management functionality is included in the HPI B daemon ATCA M100 Installation and Use in particular firmware upgrade procedure Blower IPMI firmware PEMs and Blowers of Centellis 4100 Control via IPMI Programmer s Reference Node blade Basic Blade Services Software including Install the files of the new software Operating System version as described in the Basic Hardware management functions SE Dec o were Programmer s Reference of the Set of management routines for Linux respective blade and all hardware interfaces System Management Interface Based on HPI B Centellis CO 31kX 4100 User s Guide for different blades HPI B client libraries are available PEM IPMI firmware PEMs and Blowers of Centellis 4100 Control via IPMI Programmer s Reference Supported Operating Systems Currently the Centellis 4100 supports WRS PNE 1 4 Installation
31. Requirements Before installing the RTM make sure the requirements described in this section are met Centellis 4100 Getting Started 6806800E18B 175 Installing the RTM ATCA 7221 SCS 7 1 2 1 176 Environmental Requirements The environmental conditions must be tested and proven in the used system configuration The conditions refer to the surrounding of the board within the user environment e Operating temperatures refer to the temperature of the air circulating around the ARTM and not to the actual component temperature e To ensure that the operating conditions are met forced air cooling is required within the chassis environment e The environmental values given in the table below only apply to the ARTM without any hard disk If installing hard disks their environmental requirements must also be taken into account If you use the ARTM together with a hard disk also check the environmental requirements of the hard disk and make sure that the most restrictive requirements are met RTM Damage High humidity and condensation on the RTM surface causes short circuits Do not operate the RTM outside the specified environmental limits Make sure the RTM is completely dry and there is no moisture on any surface before applying power Table 7 1 Environmental Requirements Requirement Operating Temperature 5 C 41 F to 40 C 104 F normal operation according to NEBS Standard GR 63 CORE 5 C 2
32. Reserved default OFF SW1 4 Default boot flash boot block write protection OFF Write enabled default ON Write protected SW2 1 Routing of PMC slot 1 Pn4 connector pins 30 and 31 OFF Pin 30 and 31 are routed to zone 3 backplane connector and are available as PMC I O signals default ON Pin 30 and 31 hold clock reference signals generated by clock synchronization module Centellis 4100 Getting Started 6806800E18B 191 Installing the ATCA 7221 Table 8 4 Switch Settings continued Switch Description SW2 2 Serial COM interface swapping at blade start up OFF No swapping default As a result COM1 is available via the blade s face plate and COM2 via RTM Only applicable for blades used in Centellis CO 31kX and Centellis 4100 systems Console redirection via IPMI is possible ON COM1 is swapped with COM2 As a result COM2 is available via the blade s face plate and COM1 via RTM Only applicable for blades used in Centellis CO 31kX and Centellis 4100 systems Console redirection via IPMI is not possible SW2 3 and SW2 Reserved default for both switches OFF 4 Only applicable for blades used in Centellis CO 31kX and Centellis 4100 systems SW2 3 must be ON SW2 4 must be OFF SW3 1 Boot block swapping Allows to select one of the two upper 64KByte memory blocks of the current boot flash as boot block OFF The upper 64KByte area acts as boot block default ON The lower 64KByte
33. SCSI Control via IPMI 6806800C90 Programmer s Reference ATCA 7221 HD SATA Installation Guide 6806800C16 ATCA 7221 HD SAS Installation Guide 6806800C17 ATCA 7221 MEM Installation Guide 6806800C18 Basic Blade Services Software for Centellis 4100 Release 1 0 6806800E01 A 2 Manufacturer s Documents For additional information refer to the following table for manufacturers data sheets or user s manuals As an additional help a source for the listed document is provided Please note that while these sources have been verified the information is subject to change without notice Table A 2 Manufacturer s Documents Document Source Windriver PNE 1 4 documentation Windriver http www windriver com 214 Centellis 4100 Getting Started 6806800E1 8B Related Documentation A 3 Related Specifications For additional information refer to the following table for related specifications As an additional help a source for the listed document is provided Please note that while these sources have been verified the information is subject to change without notice Table A 3 Related Specifications Document Title Source PCI Industrial Computer Manufacturers Group PICMG Specifications http www picmg org PICMG 3 0 Revision 1 0 Advanced Telecommunications Computing PICMG Architecture AdvancedTCA Base Specification December 2002 PICMG 3 1 Revision 1 0 Specification Ethernet Fibre Channel for PIC
34. T1 ports and only connect serial devices to RJ 45 connectors labeled as COM Environment Always dispose of used modules system components and RTMs according to your country s legislation and manufacturer s instructions 104 Centellis 4100 Getting Started 6806800E18B RTM ATCA 7221 SCS Sicherheitshinweise EMV Dieses Kapitel enthalt Hinweise die potentiell gefahrlichen Prozeduren innerhalb dieses Handbuchs vorrangestellt sind Beachten Sie unbedingt in allen Phasen des Betriebs der Wartung und der Reparatur des Systems die Anweisungen die diesen Hinweisen enthalten sind Sie sollten au erdem alle anderen Vorsichtsma nahmen treffen die f r den Betrieb des Produktes innerhalb Ihrer Betriebsumgebung notwendig sind Wenn Sie diese Vorsichtsma nahmen oder Sicherheitshinweise die an anderer Stelle diese Handbuchs enthalten sind nicht beachten kann das Verletzungen oder Sch den am Produkt zur Folge haben Artesyn ist darauf bedacht alle notwendigen Informationen zum Einbau und zum Umgang mit dem Produkt in diesem Handbuch bereit zu stellen Da es sich jedoch um ein komplexes Produkt mit vielf ltigen Einsatzm glichkeiten handelt k nnen wir die Vollst ndigkeit der im Handbuch enthaltenen Informationen nicht garantieren Falls Sie weitere Informationen ben tigen sollten wenden Sie sich bitte an die f r Sie zust ndige Gesch ftsstelle von Artesyn Das System erf llt die f r die Industrie geforderten Sicherheitsvorschrifte
35. The product has been designed to meet the standard industrial safety requirements It must not be used except in its specific area of office telecommunication industry and industrial control Only personnel trained by Artesyn or persons qualified in electronics or electrical engineering are authorized to install remove or maintain the product The information given in this manual is meant to complete the knowledge of a specialist and must not be used as replacement for qualified personnel Keep away from live circuits inside the equipment Operating personnel must not remove equipment covers Only factory authorized service personnel or other qualified service personnel may remove equipment covers for internal subassembly or component replacement or any internal adjustment Do not install substitute parts or perform any unauthorized modification of the equipment or the warranty may be voided Contact your local Artesyn representative for service and repair to make sure that all safety features are maintained Electrical Interference This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructio
36. area acts as boot block SW3 2 Clear CMOS RAM content OFF Normal operation default ON Clear CMOS RAM This switch can be used to restore the BIOS default settings SW3 3 Frame error mode of fibre channel 0 bypass switches OFF Multiple frame error mode default ON Single frame error mode SW3 4 Fibre channel repeater speed OFF 2Gb s ON 1Gb s default SWA 1 Reserved default OFF SW4 2 Reserved default OFF 192 Centellis 4100 Getting Started 6806800E18B Installing the ATCA 7221 Table 8 4 Switch Settings continued Switch Description SWA 3 Total Cost of Ownership TCO timer OFF Timer enabled default ON Time disabled SW4 4 BIOS crisis recovery OFF Disabled default ON Enabled SW12 1 Reserved default OFF SW12 2 Frame error mode of fibre channel 1 bypass switches OFF Multiple frame error mode default ON Single frame error mode SW12 3 Reserved default OFF SW12 4 Face plate reset enabling OFF Enabled default ON Disabled Centellis 4100 Getting Started 6806800E18B 193 Installing the ATCA 7221 8 4 PMC Module The blade provides one PMC slot supporting PCI X based 64 bit 100 MHz PMC and PTMC modules Figure 8 3 Location of PMC Slot PMC Slot 1
37. besch digt Schalten Sie die Unterbrecher deshalb nur Centellis 4100 Getting Started 6806800E18B Centellis 4100 Shelf Sicherheitshinweise wenn das rote Feld nicht sichtbar ist Liifteraustausch Uberhitzungsgefahr Wird das System mit weniger als drei L ftermodulen betrieben kann das System besch digt werden Betreiben Sie das System nicht mit weniger als drei L ftermodulen Besch digung des Systems Wird das System f r mehr als 30 Sekunden mit offener L fterklappe betrieben zu Sch den kommen ffnen Sie beim Austausch eines L ftermodules die Klappe erst unmittelbar vor dem Austausch f hren Sie den Austausch ohne Verz gerungen durch und schlie en Sie die Klappe unmittelbar nach dem Austausch wieder Verletzungsgefahr Rotierende L fterschaufeln Sie k nnen verletzt werden wenn Sie Werkzeuge oder Finger in laufende L fter einf hren Wenn Sie die L fterschublade aus dem Chassis ziehen wird die Abdeckung der L fterschaufeln freigelegt Ber hren Sie die L fterschaufeln nicht Seien Sie vorsichtig nach dem Herausziehen des L fters da die Zentrifugalkr fte noch wirken und somit die Handhabung erschweren k nnen Verkabelung Kabelf hrung Verletzungsgefahr Ver ndern Sie nie die von Artesyn ausgelieferte Verkabelung des Systems Stellen Sie sicher dass die Verkabelung schon existierenden Kabelf hrungen folgt und bestehende oder hnliche Befestigungen verwendet berpr fen Sie nach der Erweiterung d
38. blade Any optional items ordered 2 Check for damage and report any damage or differences to the customer service 3 Remove the desiccant bag shipped together with the blade and dispose of it according to your country s legislation The blade is thoroughly inspected before shipment If any damage occurred during transportation or any items are missing please contact our customer s service immediately 8 2 Requirements In order to meet the environmental requirements the blade has to be tested in the system in which it is to be installed Centellis 4100 Getting Started 6806800E1 8B 183 Installing the ATCA 7221 Before you power up the blade calculate the power needed according to your combination of blade upgrades and accessories 8 2 1 Environmental Requirements The environmental conditions must be tested and proven in the shelf configuration used The conditions refer to the surrounding of the blade within the user environment ly Theenvironmental requirements of the blade may be further limited down due to 4 installed accessories such as hard disks or PMC modules with more restrictive environmental requirements e Operating temperatures refer to the temperature of the air circulating around the blade and not to the actual component temperature NOTICE Blade Damage Blade surface High humidity and condensation on the blade surface causes short circuits Do not operate the blade outside the specified
39. damage When operating the RTM make sure that sufficient forced air cooling is available in the shelf When operating the RTM in areas of electromagnetic radiation ensure that the RTM is bolted on the system and the system is shielded by enclosure Make sure that contacts and cables of the RTM cannot be touched while the RTM is operating RJ 45 Connector RTM and Telephone Damage E1 T1 interfaces on face plate On the face plate RJ 45 connectors are used for different interfaces Mismatching the interfaces i e connecting a telephone or an E1 T1 network to the serial interfaces labeled as COM or connecting a serial device to a RJ 45 connector labeled as E1 T1 may damage the telephone or the RTM Therefore only connect E1 T1 networks to RJ 45 connectors labeled as E1 T1 ports and only connect serial devices to RJ 45 connectors labeled as COM Laser Some variants of the RTM are a Class 1 laser product The use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure Environment Always dispose of used modules system components and RTMs according to your country s legislation and manufacturer s instructions 96 Centellis 4100 Getting Started 6806800E18B RTM ATCA 7221 FC Sicherheitshinweise Dieses Kapitel enth lt Hinweise die potentiell gef hrlichen Prozeduren innerhalb dieses Handbuchs vorrangestellt sind Beachten Sie unbedingt in allen Phasen des
40. de ee eR Re A wake WOE erase 109 1 2 MainFeat res u tat ne tegha dase oreo ae ine 109 1 21 Shell een Dr ea 112 1 2 2 Backplaner nr eek 113 1 2 3 Shelt Manager sammen toe eae ae EREA 113 1 24 Nodesl ts u ae tere re Be ee 114 1 2 5 H b Slots nass ande lin ee ay dies ie nl 114 1 2 6 RearTransition Modules 0 cece cece e cece eee nee e nnn ene en nn 114 V2 7 AMCModules 235 3 322220 es 115 1 2 8 Power Entry Modules 22222sssseeeeeeseeneenneeenseneneneeeeennnnn 115 1 2 9 BIOWEIS 20 ee ee ee tees een 115 1 2 10 Air Filter area ehe BR Aaa E eee ae Mieke EE 115 2 Site Preparati n a I a 117 2 1 OVENIEW SE ee genen serie 117 2 2 Site Planning Considerations 0c cece cece ete een en ne nennen nnne 117 2 2 1 Receiving and Unpacking the System 0 cece cece eee eee eee eens 117 2 2 2 Site and Installation Planning 0 ccc cece cece eee eee eee nennen 118 252 3 Requlrements rk kreieren 119 2 2 3 1 Environmental Requirements 0 ccc e cece eee e cence en ees 119 2 2 3 2 Power Requirements cece cece ee eee e eet eee nennen nenn 124 2 2 4 Dimensions and Weight 0c cece cece ene e nent eee een teens rennen 125 2 25 Mounting Options ne Eee Semel ES 126 2 2 6 Airflow Requirements 0 0 ccc cece cece een een ene eee ene eene tenes 128 2 2 7 Acoustic Noise Control 0 0 cece cece cece ene ene eee neeeeneeeneees 13
41. dem Board kein Kondensat befindet und betreiben Sie das Board nicht unter 0 C Wenn Sie das Board in Gebieten mit starker elektromagnetischer Strahlung betreiben stellen Sie sicher dass das Board mit dem System verschraubt ist und das System durch ein Geh use abgeschirmt wird Stellen Sie sicher dass Anschl sse und Kabel des Boards w hrend des Betriebs nicht versehentlich ber hrt werden k nnen Umweltschutz 60 Entsorgen Sie alte Batterien und oder Boards stets gem der in Ihrem Land g ltigen Gesetzgebung wenn m glich immer umweltfreundlich Centellis 4100 Getting Started 6806800E18B ATCA F120 Safety Notes This section provides warnings that precede potentially dangerous procedures throughout this manual Instructions contained in the warnings must be followed during all phases of operation service and repair ofthis equipment You should also employ all other safety precautions necessary for the operation of the equipment in your operating environment Failure to comply with these precautions or with specific warnings elsewhere in this manual could result in personal injury or damage to the equipment Artesyn intends to provide all necessary information to install and handle the product in this manual Because of the complexity of this product and its various uses we do not guarantee that the given information is complete If you need additional information ask your Artesyn representative The product has been de
42. die nicht der EN 60950 Norm entsprechen verwenden verlieren Sie die Sicherheitszulassung Benutzen Sie daher das Kabel ACC CABLE RJ45 DSUB nur zum Zweck der Instandhaltung und in Verbindung mit Produkten die der EN 60950 Norm entsprechen Verletzungen oder Kurzschl sse Blade oder Stromversorgung Falls die ORing Dioden des Blades durchbrennen kann das Blade einen Kurzschluss zwischen den Eingangsleitungen A und B verursachen In diesem Fall ist Leitung A immer noch unter Spannung auch wenn sie vom Versorgungskreislauf getrennt ist und umgekehrt Pr fen Sie deshalb immer ob die Leitung spannungsfrei ist bevor Sie Ihre Arbeit fortsetzen um Sch den oder Verletzungen zu vermeiden Ausbau Erweiterung Systemiiberlastung Verhindern Sie eine System berlastung indem Sie die gesamte aufgenomme Leistung aller eingebauten Komponenten also z B der installierten Boards und Laufwerke siehe die technischen Daten der entsprechenden Komponente berpr fen Bei Ihrem System darf die Gesamtleistung die im Abschnitt Power Requirements definierten Werte nicht berschreiten Centellis 4100 Getting Started 6806800E18B 39 Centellis 4100 Shelf Sicherheitshinweise Verlust der Sicherheitszulassung Verwendung zusatzlicher Module Wenn Sie zus tzliche Module und Boards verwenden ist es m glich dass das System nicht mehr den g ltigen Sicherheits und EMV Normen entspricht Der Systemintegrator muss die Einhaltung der g ltigen Normen siche
43. installation of the blade can cause damage of the blade Only use handles when installing removing the blade to avoid damage deformation to the face plate and or PCB Damage to blade Backplane or System Components Bent pins or loose components can cause damage to the blade the backplane or other system components Therefore carefully inspect the blade and the backplane for both pin and component integrity before installation Artesyn and our suppliers take significant steps to ensure there are no bent pins on the backplane or connector damage to the boards prior to leaving the factory Bent pins caused by improper installation or by inserting boards with damaged connectors could void the ECC warranty for the backplane or boards Data loss Removing the blade with the blue LED still blinking causes data loss Wait until the blue LED is permanently illuminated before removing the blade Centellis 4100 Getting Started 6806800E1 8B ATCA F120 Safety Notes Cabling and Connectors Blade Damage The RJ 45 connector s on the face plate are twisted pair Ethernet TPE or E1 T1 J1 interfaces Connecting an E1 T1 J1 line to an Ethernet connector may damage the product Make sure that TPE connectors near your working area are clearly marked as network connectors e Verify that the length of an electric cable connected to a TPE bushing does not exceed 100 meters Make sure the TPE bushing of the system is connected only to safety ex
44. is made all of the following conditions must be met This equipment shall be connected directly to the DC supply system earthing electrode conductor or to a bonding jumper from an earthing terminal bar or bus to which the DC supply system earthing electrode conductor is connected This equipment shall be located in the same immediate area such as adjacent cabinets as any other equipment that has a connection between the earthed conductor of the same DC supply circuit and the earthing conductor and also the point of earthing of the DC system The DC system shall not be earthed elsewhere The DC supply source shall be located within the same premises as this equipment Switching or disconnecting devices shall not be in the earthed circuit conductor between the DC source and the point of connection of the earthing electrode conductor French translation Cet appareil est con u pour permettre le raccordement du conducteur reli a la terre du circuit d alimentation c c au conducteur de terre de l appareil Pour ce raccordement toutes les conditions suivantes doivent tre respect es Ce mat riel doit tre raccord directement au conducteur de la prise de terre du circuit d alimentation c c ou a une tresse de mise a la masse reli e a une barre omnibus de terre laquelle est raccord e a l electrode de terre du circuit d alimentation c c Les appareils dont les conducteurs de terre respectifs sont raccord s au conducteur de terre du m
45. may remove equipment covers for internal subassembly or component replacement or any internal adjustment Do not install substitute parts or perform any unauthorized modification of the equipment or the warranty may be voided Contact your local Artesyn representative for service and repair to make sure that all safety features are maintained Electrical Interference This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Centellis 4100 Getting Started 6806800E1 8B 93 RTM ATCA 7221 FC Safety Notes 94 Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Changes or modifications not expressly approved by Artesyn could void the user s authority to operate the equipment A proper installation in a compliant system will maintain the required performance Use only shielded cables when connecting peripherals to assure that appropriate radio frequency emissions compliance is maintained Centellis 4100
46. of the way Make sure that the set up is comfortable for users Centellis 4100 Getting Started 6806800E1 8B 19 Centellis 4100 Shelf Safety Notes 20 System Damage Environmental contamination can impair system operation Locate the system ina stable area free of excess movement and jarring and free of dust smoke and electrostatic discharge ESD Make sure that the temperature does not exceed the operating temperature given in the environmental requirements in this manual and allow room for proper air flow for cooling Personal Injury or System Damage The system is supplied by a TNV2 voltage This voltage is considered hazardous Make sure that the power supply meets the local safety standards System Overheating Inproper cooling leads to blade damage To ensure proper cooling always operate the system in a horizontal position Furthermore keep clear at least 6 cm adjacent to the cooling vents on the chassis front and back side For detailed information refer to Site Planning Considerations on page 117 Personal or System Damage Unstable system installation in a rack can cause the rack to topple over Therefore if your system is the only one in the rack make sure to mount the system in the lowest part of the rack If other systems are installed in one rack start with the heaviest component at the bottom If the rack is equipped with stabilizing devices make sure that they are installed and extended so that the rack is se
47. protection OFF User flash 1 write enabled default ON User flash 2 write protected SW2 4 User flash 2 write protection OFF User flash 2 write enabled default ON User flash 2 write protected SW3 1 Boot flash selection OFF IPMI selects boot flash default ON Switch SW3 2 determines boot flash 154 Centellis 4100 Getting Started 6806800E18B Installing the ATCA F120 Table 5 4 Switch Settings continued Switch Description SW3 2 Determines boot flash only if switch SW3 1 is set to ON OFF Blade boots from boot flash 1 default ON Blade boots from boot flash 2 SW3 3 Watchdog timer enabling This switch allows to enable disable the watchdog inside the FPGA OFF Watchdog enabled default ON Watchdog disabled SW3 4 Reserved default OFF SWA 1 Reserved default OFF SW4 2 Reserved default OFF SWA 3 Reserved default OFF SW4 4 Reserved default OFF 5 5 Blade Installation The blade is fully compatible to the AdvancedTCA standard and is designed to be used in AdvancedTCA shelves Centellis 4100 Getting Started 6806800E18B 155 Installing the ATCA F120 The blade must only be installed into hub slots of your shelf Refer to the system s documentation for information which slots these are in your particular configuration NOTICE Damage of Circuits Electrostatic discharge and incorrect blade installation and removal can damage c
48. provides warnings that precede potentially dangerous procedures throughout this manual Instructions contained in the warnings must be followed during all phases of operation service and repair of this equipment You should also employ all other safety precautions necessary for the operation of the equipment in your operating environment Failure to comply with these precautions or with specific warnings elsewhere in this manual could result in personal injury or damage to the equipment Artesyn intends to provide all necessary information to install and handle the product in this manual Because of the complexity of this product and its various uses we do not guarantee that the given information is complete If you need additional information ask your Artesyn representative The product has been designed to meet the standard industrial safety requirements It must not be used except in its specific area of office telecommunication industry and industrial control Only personnel trained by Artesyn or persons qualified in electronics or electrical engineering are authorized to install remove or maintain the product The information given in this manual is meant to complete the knowledge of a specialist and must not be used as replacement for qualified personnel Keep away from live circuits inside the equipment Operating personnel must not remove equipment covers Only factory authorized service personnel or other qualified service personnel
49. radio communications Centellis 4100 Getting Started 6806800E1 8B 61 ATCA F120 Safety Notes 62 Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Changes or modifications not expressly approved by Artesyn could void the user s authority to operate the equipment Blade products are tested in a representative system to show compliance with the above mentioned requirements A proper installation in a compliant system will maintain the required performance Use only shielded cables when connecting peripherals to assure that appropriate radio frequency emissions compliance is maintained Centellis 4100 Getting Started 6806800E1 8B ATCA F120 Safety Notes Operation Blade Damage High humidity and condensation on the blade surface causes short circuits Do not operate the blade outside the specified environmental limits Make sure the blade is completely dry and there is no moisture on any surface before applying power Do not operate the blade below 5 C Overheating and Blade Damage Operating the blade without forced air cooling may lead to overheating and thus damage of the blade When operating the blade make sure that forced air cooling is available in the shelf Injuries or Short Circuits Blade or power supply In case the ORing diodes of the blade fail the blade may trigger a short circuit betwee
50. system in a rack 134 Centellis 4100 Getting Started 6806800E18B NOTICE Installing the System Observe the following general safety notes when installing your system e Restricted access area The system is only to be installed in a restricted access area e Installation codes This unit must be installed in accordance with the National Electrical Code Articles 110 16 110 17 and 110 18 and the Canadian Electrical Code Section 12 e Conductor ampacity According to UL 60950 Annex NAE NEC Article 645 5 a the branch circuit conductors supply must have an ampacity of not less than 125 of the total connected load Per NEC Article 310 15 and Table 310 16 the minimum American Wire Gauge AWG has to be selected e Overcurrent protection A readily accessible listed branch circuit overcurrent protective device must be incorporated into the building wiring Artesyn is not responsible for regulatory compliance or malfunction of any user modified product NOTICE System Damage Environmental contamination can impair system operation Locate the system in a stable area free of movement and free of dust smoke and electrostatic discharge ESD Make sure that the temperature does not exceed the operating temperature given in the environmental requirements in this manual and allow room for proper air cooling System Overheating Improper cooling leads to blade damage To ensure proper cooling always operate the
51. the equipment or the warranty may be voided Contact your local Artesyn representative for service and repair to make sure that all safety features are maintained Centellis 4100 Getting Started 6806800E1 8B 17 Centellis 4100 Shelf Safety Notes General EMC 18 Danger of Injuries At the system s rear there are sharp pins which can cause injuries Be careful when handling the system The product has been tested and found to comply with the limits for a Class A digital device in this system pursuant to part 15 of the FCC Rules EN 55022 Class A respectively These limits are designed to provide reasonable protection against harmful interference when the product is operated in a commercial business or industrial environment The product generates and uses radio frequency energy and if not installed properly and used in accordance with this user s documentation may cause harmful interference to radio communications Operating the product in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense To ensure proper EMC shielding operate the system only with free slots populated with filler blades Grounding To ensure the system is properly grounded each of the system s parts contact the EMI gasket The system contains gaskets at the shelf and module level The shelf is also fitted with ESD contacts Please take care for proper ESD protection
52. the power feeds you plan to remove or attach are powered off and cannot be switched on while you are working Ensure that all power input lines are not energized Short Circuit and Electric Shock To avoid short circuits and electric shock the power lugs must not be energized before removing the screws It is essential to ensure that the power lugs are not energized before loosening the screws Be careful with the used tools in order to prevent a short circuit Personal Injury PEMs will get hot Touching a hot PEM can cause injuries Let the PEM cool down before pulling it out with bare hands PEM Damage Applying reversal power causes damage to the electrolytic capacitors of the filter Therefore only switch on the breakers if no red light is visible Exchanging Blowers System Overheating Running the system with less than three blowers may damage the system Do not operate the system with less than three blowers 26 Centellis 4100 Getting Started 6806800E18B Centellis 4100 Shelf Safety Notes Cabling System Damage Operating the system with the blower cover open for more than 30 seconds may damage the system When replacing a blower make sure to open the blower cover only immediately before the replacement perform the replacement without delays and close it immediately after the replacement When a blower is taken out of operation the system manager will compensate for the loss by increasing the speed of the remaining bl
53. to radio communications Operating the system in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Centellis 4100 Getting Started 6806800E1 8B ATCA 7221 Safety Notes Installation Damage of Circuits Electrostatic discharge and incorrect blade installation and removal can damage circuits or shorten their life Before touching the blade or electronic components make sure that you are working in an ESD safe environment Data Loss Removing the blade with the blue LED still blinking causes data loss Wait until the blue LED is permanently illuminated before removing the blade Damage of Blade and Additional Devices and Modules Incorrect installation of additional devices or modules may damage the blade or the additional devices or modules Before installing or removing an additional device or module read the respective documentation Operation Blade Damage Blade surface High humidity and condensation on the blade surface causes short circuits Do not operate the blade outside the specified environmental limits Make sure the blade is completely dry and there is no moisture on any surface before applying power Blade Overheating and Blade Damage Operating the blade without forced air cooling may lead to blade overheating and thus blade damage When operating the blade make sure that forced air cooling is available in the shelf
54. type label location Installation This section provides information about how to mount the system into a rack and how to ground the system 3 2 Before Installation This section provides the following information e Type label location Requirements e Tools you will need 3 2 1 Type Label Location The serial number label for the shelf is located at the lower part on the right hand side of the chassis 3 2 2 Requirements Please ensure that the requirements outlined in section Requirements on page 119 are met The power input cables must have a minimum cross section of 6 mm AWG 8 Centellis 4100 Getting Started 6806800E1 8B 133 Installing the System 3 2 3 Tools You Will Need Before you start the installation make sure that you have all the necessary equipment at hand Usage Equipment General Philipps head screwdriver 1 and 2 Wrenches 7 8 10 mm or 0 28 0 31 0 39 inch Crescent wrench Socket wrench Large and small socket screwdriver Large medium and small Philipps screwdrivers Antistatic mat ESD wrist strap Shelf Transport equipment Hand truck or forklift pallet truck Lifting equipment for installation PEM Cable from Thomas amp Betts P N 256 30695 1225 or equivalent cables System Access Crossover cable Twisted pair Ethernet cable 3 3 Installation This section provides the information and instructions needed to mount a
55. when connecting peripherals to assure that appropriate radio frequency emissions compliance is maintained 74 Centellis 4100 Getting Started 6806800E18B RTM ATCA F120C Safety Notes Operation Damage of the RTM High humidity and condensation on the RTM surface causes short circuits Do not operate the RTM outside the specified environmental limits Make sure the RTM is completely dry and there is no moisture on any surface before applying power Do not operate the RTM below 5 C Installation Damage of the RTM and Additional Devices and Modules Incorrect installation or removal of additional devices or modules may damage the RTM or the additional devices or modules Before installing or removing additional devices or modules read the respective documentation Damage of Circuits Electrostatic discharge and incorrect installation and removal of the RTM can damage circuits or shorten their life Before touching the Product Name or electronic components make sure that your are working in an ESD safe environment Damage of the RTM Incorrect installation of the RTM can cause damage of the RTM Only use handles when installing removing the RTM to avoid damage deformation to the face plate and or PCB Damage to RTM Backplane or System Components Bent pins or loose components can cause damage to the RTM the backplane or other system components Therefore carefully inspect the RTM and the backplane for both pin and compone
56. 0 23 SitelPl nning Checklists cco lee De ne Da abe ead ele eae 131 3 Installmgthe system 2 133 3 1 OVEIVIEW an ee 133 3 2 Beforellnstall tion u a u 133 3 2 1 TypeLabellocation 0 ccc cece cece eee nent n een enne nennen 133 4 Centellis 4100 Getting Started 6806800E1 8B Centellis 4100 Getting Started 6806800E18B 322 IREQUIFEMENES rn ee oe nn 133 3 2 3 Tools YouWilllNeed u sn sae ns een seen 134 33 Installation au ame ee a RR Denen 134 3 3 1 Installing the System in a Rack 6 ccc cece eee e eee ne nennen 136 3 3 2 Ground System Bonding 6 c cece cece eee eee nee een ee eeneeenenes 138 Installing the RTM ATCA F120C 21 ccc ccc ccc cc cece e eee nennen nn ns ns nine nenn nn ne 141 4 OVEIVIEW ren nl ame nee 141 4 2 Unpacking and Inspecting the RTM ese cece ect eeeee nee teen nent nee n ee aee 141 4 3 Environmental and Power Requirements 00 cece eee cece cece een eee e een enaee 142 4 3 1 Environmental Requirements 0c ccc e cece cece e een ee eee ee tenance 142 4 3 2 Power Requirements eect teen e eee ee a e eee eens 143 4A Module Installation 0 cece ccc eee nee e nee nent ene een eeeneeenee 144 4 4 1 Installing the RTM cece ccc ccc cece teen cent e nee n ete sent eneennees 145 installing the ATCA F120 u ce 147 Dell OVERVIOW anreisen 147 5 2 Unpacking and Inspecting the Blade 0 ccc cece eee nee n eee e een eenee
57. 0 Getting Started 6806800E18B 11 List of Figures eee EEE 12 Centellis 4100 Getting Started 6806800E18B About this Manual sis Overview of Contents This Getting Started manual is organized as follows Chapter Description About this Manual Lists all conventions and abbreviations used in this manual and outlines the revision history Safety Notes Sicherheitshinweise Describes the safety information which has to be regarded For legal reasons the German translation is included as well Introduction Provides an overview of this guide and lists the main features of the Centellis 4100 system Site Preparation Provides important information which needs to be taken into account before setting up and installing system Installing the System Describes how to install and connect the system Installation chapters Describes how to install available blades RTMs into the system Starting up the System Describes how to start up the system System Software Describes briefly which system software is available and where to find detailed information about it Related Documentation Lists manuals documents which provide detailed information about all system components both software and hardware Abbreviations This document uses the following abbreviations Abbreviation Definition AdvancedTCA Advanced Telecom Computing Architecture AMC AdvancedTCA Mezzanine Card ARTM AdvancedTC
58. 00E18B 167 Installing the RTM ATCA 7221 FC 6 1 2 1 6 1 2 2 168 Power Requirements The RTM draws approximately 5W from the front blade that is connected Environmental Requirements The environmental conditions must be tested and proven in the used system configuration The conditions refer to the surrounding of the board within the user environment e Operating temperatures refer to the temperature of the air circulating around the RTM and not to the actual component temperature e Toensure that the operating conditions are met forced air cooling is required within the chassis environment e The environmental values given in the table below only apply to the RTM without any hard disk If installing hard disks their environmental requirements must also be taken into account If you use the RTM together with a hard disk also check the environmental requirements of the hard disk and make sure that the most restrictive requirements are met RTM Damage High humidity and condensation on the RTM surface causes short circuits Do not operate the RTM outside the specified environmental limits Make sure the RTM is completely dry and there is no moisture on any surface before applying power Centellis 4100 Getting Started 6806800E18B Installing the RTM ATCA 7221 FC Table 6 1 Environmental Requirements Requirement Operating Non Operating Temperature 5 C 41 F to 40 C 104 F
59. 06800E18B SPARE ATCA A100 Safety Notes ee This section provides safety precautions to follow when installing operating and maintaining the board We intend to provide all necessary information to install and handle the product in this manual However as the product is complex and its usage manifold we do not guarantee that the given information is complete If you need additional information ask your Artesyn representative The board has been designed to meet the standard industrial safety requirements It must not be used except in its specific area of office telecommunication industry and industrial control Only personnel trained by Artesyn or persons qualified in electronics or electrical engineering are authorized to install remove or maintain the product The information given in this manual is meant to complete the knowledge of a specialist and must not be taken as replacement for qualified personnel EMC The board has been tested in a standard Artesyn system and found to comply with the limits for a Class A digital device in this system pursuant to part 15 of the FCC Rules EN 55022 Class A respectively These limits are designed to provide reasonable protection against harmful interference when the system is operated in a commercial environment The board generates and uses radio frequency energy and if not installed properly and used in accordance with this guide may cause harmful interference to radio communications O
60. 0E18B Installing the ATCA 7221 8 2 2 188 Power Requirements The blade s power requirements depend on the installed hardware accessories If you want to install accessories on the board the load of the respective accessory has to be added to that of the blade In the following table you will find typical examples of power requirements with and without accessories installed For information on the accessories power requirements refer to the documentation delivered together with the respective accessory or consult your local Artesyn representative for further details The blade must be connected to a TNV 2 or a safety extra low voltage SELV circuit A TNV 2 circuit is a circuit whose normal operating voltages exceed the limits for a SELV circuit under normal operating conditions and which is not subject to overvoltages from telecommunication networks The typical power consumption of the ATCA 7221 equipped with a PMC module and an RTM ATCA 7221 FC with installed hard disk is 160 200W Theoretically this range can be exceeded when all blade resources are operated in parallel with maximum loading and when additionally all external interfaces such as USB COM1 etc are loaded with their maximum specified power ratings Table 8 3 Power Requirements Characteristic Value Rated Voltage 48VDC to 60VDC Exception in the US and Canada 48VDC Operating Voltage 40VDC to 72VDC Exception in the US and Canada 40VDC to 60
61. 1 Environmental Requirements Requirement Temperature Operating 5 C to 40 C normal operation according to NEBS Standard GR 63 CORE 5 C to 55 C exceptional operation according to NEBS Standard GR 63 CORE Non Operating 40 C to 70 C Temp Change 0 25 C min according to NEBS Standard GR 63 CORE 0 25 C min Rel Humidity 5 to 90 non condensing according to Artesyn internal environmental requirements 5 to 95 non condensing according to Artesyn internal environmental requirements Vibration 0 1g from 5 to 100 Hz and back to 5 Hz at a rate of 0 1 octave minute 5 20 Hz 0 01 g Hz 20 200 Hz 3 0 dB octave Random 5 20 Hz 1 m Sec Random 20 200 Hz 3 m Sec Shock Half sine 11 m Sec 30mSec sec Blade level packaging Half sine 6 mSec at 180 m Sec Free Fall 1 200 mm all edges and corners 1 0m Packaged per ETSI 300 019 2 2 Blade level packaging 100mm unpackaged per GR 63 CORE 4 3 2 Power Requirements The RTM has a typical power dissipation of 22W and a maximum power dissipation of 30W Centellis 4100 Getting Started 6806800E18B 143 Installing the RTM ATCA F120C 4 4 Module Installation The RTM can be installed into a powered or non powered system NOTICE RTM Damage Installing the RTM with other blades than the ATCA F120 may damage the RTM and the front blade Only install the RTM with the Ar
62. 3 F to 55 C 131 F exceptional operation according to NEBS Standard GR 63 CORE All values may be further limited by installed accessories with more restrictive environmental requirements Non Operating 40 C 40 F to 70 C 158 F may be further limited by installed accessories Temp 0 25 C min according to NEBS Standard Change GR 63 CORE 0 25 C min Centellis 4100 Getting Started 6806800E18B Installing the RTM ATCA 7221 SCS Table 7 1 Environmental Requirements continued Requirement Operating Non Operating Rel Humidity 5 to 95 non condensing according to 5 to 95 non condensing according Artesyn internal environmental to Artesyn internal environmental requirements requirements Altitude Up to 3 000 m Up to 12 000 m Vibration 5 20 Hz 0 5 mm amplitude 1 mm amplitude 20 250 Hz 1g 2 0g Shock 5 g 11 ms halfsine according to Artesyn 15 g 11 ms half sine according to internal environmental requirements Artesyn internal environmental requirements Free Fall 1 200 mm all edges and corners In order to ensure proper RTM operation you have to make sure that the temperatures at the following locations are not exceeded If not stated otherwise the temperatures should be measured exactly at the given locations Table 7 2 Critical Temperature Limits Location Component Temperature Limit 1 Installed hard disk 60 C 140 F normal o
63. 6806800E18B RTM ATCA F120C Sicherheitshinweise Operation Besch digung des RTMs Hohe Luftfeuchtigkeit und Kondensat auf der Oberfl che des RTMs k nnen zu Kurzschl ssen f hren Betreiben Sie das RTM nur innerhalb der angegebenen Grenzwerte f r die relative Luftfeuchtigkeit und Temperatur Stellen Sie vor dem Einschalten des Stroms sicher dass sich auf dem Produkt kein Kondensat befindet und betreiben Sie das RTM nicht unter 5 C Installation Besch digung des RTMs und von Zusatzmodulen Fehlerhafte Installation von Zusatzmodulen kann zur Besch digung des RTMs und der Zusatzmodule f hren Lesen Sie daher vor der Installation von Zusatzmodulen die zugeh rige Dokumentation Besch digung von Schaltkreisen Elektrostatische Entladung und unsachgem er Ein und Ausbau von Blades RTMs kann Schaltkreise besch digen oder ihre Lebensdauer verk rzen Bevor Sie Blades RTMs oder elektronische Komponenten ber hren vergewissern Sie sich da Sie in einem ESD gesch tzten Bereich arbeiten Besch digung des RTMs Fehlerhafte Installation des RTMs kann zu einer Besch digung des RTMs f hren Verwenden Sie die Handles um das RTM zu installieren deinstallieren Auf diese Weise vermeiden Sie dass das Face Plate oder die Platine deformiert oder zerst rt wird Besch digung des RTMs der Backplane oder von System Komponenten Verbogene Pins oder lose Komponenten k nnen zu einer Besch digung des RTMs der Backplane oder von Syst
64. 806800E18B 157 Installing the ATCA F120 5 Fully insert the blade and lock it to the shelf by squeezing the lever and the latch together and turning the handles towards the face plate If your shelf is powered as soon as the blade is connected to the backplane power pins the blue LED is illuminated When the blade is completely installed the blue LED starts to blink This indicates that the blade announces its presence to the shelf management controller Niy If an RTM is connected to the front blade make sure that the handles of both the RTM and the front blade are closed in order to power up the blade s payload 6 Wait until the blue LED is switched off then tighten the face plate screws which secure the blade to the shelf 158 Centellis 4100 Getting Started 6806800E18B Installing the ATCA F120 When the blue LED is switched OFF and the green LED OK is switched ON this indicates that the blade s payload has been powered up and that the blade is active 7 Connect cables to the face plate if applicable 5 6 AMC Modules The blade provides two AMC bays AMC B4 and AMC B1 Their location is shown in the following figure Centellis 4100 Getting Started 6806800E18B 159 Installing the ATCA F120 Figure 5 3 Location of AMC Bays 160 Centellis 4100 Getting Started 6806800E18B Installing the ATCA F120 The following sections describe w
65. A Rear Transition Module ATCA Advanced Telecommunications Computing Architecture AWG American Wire Gauge BBS Basic Blade Services EMC Electromagnetic Compatibility Centellis 4100 Getting Started 6806800E18B 13 About this Manual Abbreviation Definition EMI Electromagnetic Interference EMV Elektromagnetische Vertraeglichkeit EN European Norm ESD Electrostatic Discharge ETSI European Telecommunication Standards Institute FCC Federal Communications Commission FCU Firmware Upgrade Utility FRU Field Replaceable Unit FUMI Firmware Update Management Instrument GmbH Gesellschaft mit beschraenkter Haftung HPI Hardware Platform Interface IEC International Electric Code IPM Intelligent Platform Management IPMB Intelligent Platform Management Bus IPMC Intelligent Platform Management Controller IPMI Intelligent Platform Management Interface MMC Mezzanine Management Controller NAE National Academy of Engineering NEBS Network Equipment Building System NEC National Electric Code OEM Original Equipment Manufacturer PEM Power Entry Module PICMG PCI Industrial Computer Manufacturers Group PMC PCI Mezzanine Card RMCP Remote Management Control Protocol RoHS Restriction of Certain Hazardous Substances RTM Rear Transition Module SAF Service Availability Forum 14 Centellis 4100 Getting Started 6806800E18B About this Manual Abbreviation
66. Centellis 4100 Getting Started P N 6806800E18B September 2014 PSS SSE O a rk Z wa E ae u EMBEDDED TECHNOLOG a z IE 0 Copyright 2014 Artesyn Embedded Technologies Inc All rights reserved Trademarks Artesyn Embedded Technologies Artesyn and the Artesyn Embedded Technologies logo are trademarks and service marks of Artesyn Embedded Technologies Inc 2014 Artesyn Embedded Technologies Inc All other product or service names are the property of their respective owners Intel is a trademark or registered trademark of Intel Corporation or its subsidiaries in the United States and other countries Java and all other Java based marks are trademarks or registered trademarks of Oracle America Inc in the U S and other countries Microsoft Windows and Windows Me are registered trademarks of Microsoft Corporation and Windows XP is a trademark of Microsoft Corporation PICMG CompactPCI AdvancedTCA and the PICMG CompactPCI and AdvancedTCA logos are registered trademarks of the PCI Industrial Computer Manufacturers Group UNIX is a registered trademark of The Open Group in the United States and other countries Notice While reasonable efforts have been made to assure the accuracy of this document Artesyn assumes no liability resulting from any omissions in this document or from the use of the information obtained therein Artesyn reserves the right to revise this document and to make changes
67. E 30 Centellis 4100 Getting Started 6806800E18B Centellis 4100 Shelf Sicherheitshinweise Dieses Kapitel enth lt Hinweise die potentiell gef hrlichen Prozeduren innerhalb dieses Handbuchs vorrangestellt sind Beachten Sie unbedingt in allen Phasen des Betriebs der Wartung und der Reparatur des Systems die Anweisungen die diesen Hinweisen enthalten sind Sie sollten au erdem alle anderen Vorsichtsma nahmen treffen die f r den Betrieb des Systems innerhalb Ihrer Betriebsumgebung notwendig sind Wenn Sie diese Vorsichtsma nahmen oder Sicherheitshinweise die an anderer Stelle diese Handbuchs enthalten sind nicht beachten kann das Verletzungen oder Sch den am System zur Folge haben Artesyn ist darauf bedacht alle notwendigen Informationen zum Einbau und zum Umgang mit dem System in diesem Handbuch bereit zu stellen Da es sich jedoch bei dem System um ein komplexes Produkt mit vielf ltigen Einsatzm glichkeiten handelt k nnen wir die Vollst ndigkeit der im Handbuch enthaltenen Informationen nicht garantieren Falls Sie weitere Informationen ben tigen sollten wenden Sie sich bitte an die f r Sie zust ndige Gesch ftsstelle von Artesyn Das System erf llt die f r die Industrie geforderten Sicherheitsvorschriften und darf ausschlie lich f r Anwendungen in der Telekommunikationsindustrie im Zusammenhang mit Industriesteuerungen und in der Entwicklung verwendet werden Es darf nicht in sicherheitskritischen Anwendungen l
68. Getting Started 6806800E1 8B RTM ATCA 7221 FC Safety Notes Installation Damage of Circuits Electrostatic discharge and incorrect installation and removal of the product can damage circuits or shorten their life Before touching the product or electronic components make sure that your are working in an ESD safe environment Product Damage Incorrect installation of the product can cause damage of the product Only use handles when installing removing the product to avoid damage deformation to the face plate and or PCB Data Loss Removing the RTM with the system power on and the blue LED on the front blade still flashing causes data loss Before removing the RTM from a powered system power down the slot by opening the lower handle of the front blade and wait until the blue LED is permanently ON RTM Damage Installing the RTM with other blades than the ATCA 7221 damages the RTM Only install the RTM with the Artesyn ATCA 7221 blade Operation Product Damage Surface High humidity and condensation on the product surface causes short circuits Do not operate the product outside the specified environmental limits Make sure the product is completely dry and there is no moisture on any surface before applying power RTM Overheating and RTM Damage Operating the RTM without sufficient forced air cooling may lead to RTM overheating and thus Centellis 4100 Getting Started 6806800E1 8B 95 RTM ATCA 7221 FC Safety Notes RTM
69. Grounding To ensure the system is properly grounded each of the system s parts contact the EMI gasket The system contains gaskets at the shelf and module level The shelf is also fitted with ESD contacts Please take care for proper ESD protection of the operator Procedure To install a system proceed as follows 1 Insert the system into a standard 19 ANSI rack 2 Fasten the system to the rack via the mounting brackets using eight bolts or screws minimum 6 mm 0 24 inch in diameter on the left side and eight on the right side of the system 3 Make sure that the system has been located in a place with room temperature for at least 24 hours before powering it up Centellis 4100 Getting Started 6806800E18B 137 Installing the System You have to keep the following conditions when installing the system into an at least 600 mm 23 62 inch deep rack The physical dimensions in the figure below are in millimeters Please ensure that 60 of the rack s rear is open Figure 3 1 Rack Mounting Dimensions Air outlet Rear PEM protective cover l PEM 600 mm deep rack 3 3 2 Ground System Bonding The following section provides information needed to ground the system 138 Centellis 4100 Getting Started 6806800E18B Installing the System Procedure To ground the system proceed as follows 1 Connect the rack ground lug to the M6 shelf ground at the bottom right rear of the shelf and torqu
70. MG AdvancedTCA Systems January 2003 Service Availability Forum Specifications http www saforum org SAI HPI B 01 01 Hardware Platform Interface Specification SA Forum SAI AIS A 01 01 Application Interface Specification SA Forum SAI HPI SNMP B 01 01 SA Forum SAIM HPI B 01 01 ATCA SAF HPI to AdvancedTCA Mapping Specification SA Forum Centellis 4100 Getting Started 6806800E1 8B 215 Related Documentation eee EEE 216 Centellis 4100 Getting Started 6806800E18B AR Fa FEZ VG lig Z wem E Ew YF i EMBEDDED TECHNOLOGIES Artesyn Embedded Technologies Artesyn and the Artesyn Embedded Technologies logo are trademarks and service marks of Artesyn Embedded Technologies Inc All other product or service names are the property of their respective owners 2014 Artesyn Embedded Technologies Inc
71. Ma nahmen durchzuf hren Centellis 4100 Getting Started 6806800E18B RTM ATCA 7221 FC Sicherheitshinweise Installation Betrieb Besch digung von Schaltkreisen Elektrostatische Entladung und unsachgem er Ein und Ausbau von Blades kann Schaltkreise besch digen oder ihre Lebensdauer verk rzen Bevor Sie Blades oder elektronische Komponenten ber hren vergewissern Sie sich dass Sie in einem ESD gesch tzten Bereich arbeiten Besch digung des Produktes Fehlerhafte Installation des Produktes kann zu einer Besch digung des Produktes f hren Verwenden Sie die Handles um das Produkt zu installieren deinstallieren Auf diese Weise vermeiden Sie dass das Front Panel oder die Platine deformiert oder zerst rt wird Besch digung des RTMs Wenn Sie das RTM nicht zusammen mit dem ATCA 7221 Front Blade installieren wird das RTM besch digt Installieren Sie das RTM deshalb nur zusammen mit dem Artesyn ATCA 7221 Front Blade Datenverlust Wenn Sie das RTM aus einem eingeschaltetem System herausziehen w hrend die blaue LED auf dem Front Blade noch blinkt gehen Daten verloren Bevor Sie das RTM aus einem eingeschaltetem System herausziehen m ssen Sie den Steckplatz durch Oeffnen des unteren Griffs am Front Blade ausschalten und warten bis die blaue LED auf dem Front Blade permanent leuchtet Besch digung des Produktes Hohe Luftfeuchtigkeit und Kondensat auf der Oberfl che des Blades k nnen zu Kurzschl ssen f hren Be
72. Options 12 18 Unused 19 Zone 3 connector P30 row 7 pin pair A B 20 Unused The AMC modules installed in AMC bay B4 of both Centellis 4100 blades in a shelf are interconnected via the AdvancedTCA update Channel interface ports 2 and 3 through the backplane The following figure illustrates the interconnection scheme It is applicable to all Artesyn AdvancedTCA shelves Figure 5 4 AMC Module B4 Interconnection Scheme Hub Slot 1 AdvancedTCA update Hub Slot 2 channel port 3 AMC port 0 AdvancedTCA update channel port 2 AMC port 0 5 6 1 2 AMC Bay B1 This AMC bay is designed to support different types of AMC modules The mechanical design allows to install single width AMCs with midsize face plates 162 Centellis 4100 Getting Started 6806800E18B Installing the ATCA F120 The AMC interfaces of AMC bay B1 provide support for the following types of AMC modules e Network security AMCs e Telecom clocking AMCs e Storage AMCs The following table describes in detail how the AMC ports of Bay B1 are assigned on the ATCA F120 Table 5 6 AMC Bay B1 Port Assignments Connector Region AMC Port Usage on ATCA F120 Clocking 1 CH1 CLK1 CH1 CLK2 2 3 PCI Express HCSL 100 MHz clock 0 Common Options Base Channel switch port 21 _ Fabric channel switch 2 port 17 AMC B4 port 2 AMC B4 port 3 AMC B4 port 4 AMC B4 port 5 AMC B4 port 6 AMC B4 port 7 Fabric Channel switch 2 port 18
73. RTM aus einem eingeschaltetem System herausziehen w hrend die blaue LED auf dem Front Blade noch blinkt gehen Daten verloren Bevor Sie das RTM aus einem eingeschaltetem System herausziehen m ssen Sie den Steckplatz durch Oeffnen des unteren Griffs am Front Blade ausschalten und warten bis die blaue LED auf dem Front Blade permanent leuchtet Besch digung des Produktes Hohe Luftfeuchtigkeit und Kondensat auf der Oberfl che des Blades k nnen zu Kurzschl ssen f hren Betreiben Sie das Produkt nur innerhalb der angegebenen Grenzwerte f r die relative Luftfeuchtigkeit und Temperatur Stellen Sie vor dem Einschalten des Stroms sicher dass sich auf dem Produkt kein Kondensat befindet Centellis 4100 Getting Started 6806800E1 8B 107 RTM ATCA 7221 SCS Sicherheitshinweise berhitzung und Besch digung des RTMs Betreiben Sie das RTM ohne Zwangsbel ftung kann das RTM berhitzt und schlie lich besch digt werden Bevor Sie das RTM betreiben m ssen Sie sicher stellen dass das Shelf ber eine ausreichende Zwangsk hlung verf gt Wenn Sie das RTM in Gebieten mit starker elektromagnetischer Strahlung betreiben stellen Sie sicher dass das RTM mit dem System verschraubt ist und das System durch ein Geh use abgeschirmt ist Stellen Sie sicher dass Anschl sse und Kabel des RTMs w hrend des Betriebs nicht versehentlich ber hrt werden k nnen RJ 45 Stecker Besch digung des RTMs und des Telefons RJ 45 Stecker an der Fron
74. Started 6806800E18B 121 Site Preparation Figure 2 1 Hot Spot Air Inlet Boe 122 Centellis 4100 Getting Started 6806800E18B Site Preparation EEE Figure 2 2 Hot Spot Air Outlet Centellis 4100 Getting Started 6806800E18B 123 Site Preparation Figure 2 3 Hot Spot Power Entry Module 2 2 3 2 Power Requirements Make sure that a suitable 40 0 to 72VDC power source is within reach ofthe system Four power entry modules PEMs can be installed in the system Personal or System Damage The system is supplied by a TNV 2 voltage This voltage is considered hazardous Make sure that the power supply unit meets the local safety standards 124 Centellis 4100 Getting Started 6806800E18B Site Preparation Table 2 3 System Power Requirements Feature Value Rated voltage and input current 81 67A at 48 to 60VDC US and Canada 81A at 48VDC Operating voltage range 40 0 to 72VDC US and Canada 40 0VDC to 60VDC Maximum power dissipation The power distribution is tested for supplying 215W front slot to all slots simultaneously and additionally 25W rear slot tz When installing addit
75. VDC Centellis 4100 Getting Started 6806800E18B Installing the ATCA 7221 Table 8 3 Power Requirements continued Characteristic Value Max power consumption of ATCA 7221 equipped with 8 Gbyte SDRAM 190W without accessories Max power consumption of ATCA 7221 with installed SRAM Flash 232W Memory Module and RTM ATCA 7221 FC with installed hard disk four DIMM modules total 8 GB one PMC module with 7 5W resistive load each USB output and PS2 output loaded with 2 5W total 15W Running software was 3xBurnP6 and 1xBurnPx worst case for full function of system 100 processor load and memory load and communication as well as read write Max power consumption of ATCA 7221 with installed SRAM Flash 234W Memory Module and RTM ATCA 7221 SCS with installed on board hard disk and two external hard disks connected four DIMM modules total 8 GB one PMC module with 7 5W resistive load each USB output and PS2 output loaded with 2 5W total 12 5W Running software was 3xBurnP6 and 1xBurnPx worst case for full function of system 100 processor load and memory load and communication as well as read write Max total power consumption of the PMC site 7 5W The blade provides two independent power inputs according to the AdvancedTCA Specification Each input has to be equipped with an additional fuse of max 90A located either in the shelf where the blade is installed or the power entry module PEM
76. ales representative for release notes or errata sheets that may be applicable to the Centellis 4100 or any related product Main Features The Centellis 4100 system is a high availability AdvancedTCA Advanced Telecom Computing Architecture system The PICMG 3 X AdvancedTCA Specifications define components for high performance services solutions It is an architecture for highly available and scalable high speed interconnect technologies A high availability system consists of software and redundant hardware to ensure five nines 99 999 uptime This means that a system is unavailable for no more than 5 26 minutes per year The system is always equipped with e Dual star backplane with base and fabric interface providing connector interfaces for power distribution input output connectivity between front blades and mechanical alignment and support e Subrack providing attachment points for backplane alignment support and mechanical engagement for insertion and extraction of front blades and RTMs Centellis 4100 Getting Started 6806800E18B 109 Introduction Two Artesyn ATCA M100 shelf manager boards Each AdvancedTCA blade and Field Replaceable Unit FRU provides connections to the shelf manager through an Intelligent Platform Management Bus IPMB e Two Artesyn ATCA A100 alarm boards e 12 node slots which can be equipped with AdvancedTCA node blades e Two hub slots which can be equipped with AdvancedTCA hub blades e 14 slot
77. apitel enth lt Hinweise die potentiell gef hrlichen Prozeduren innerhalb dieses Handbuchs vorrangestellt sind Beachten Sie unbedingt in allen Phasen des Betriebs der Wartung und der Reparatur des Systems die Anweisungen die diesen Hinweisen enthalten sind Sie sollten au erdem alle anderen Vorsichtsma nahmen treffen die f r den Betrieb des Blades innerhalb Ihrer Betriebsumgebung notwendig sind Wenn Sie diese Vorsichtsma nahmen oder Sicherheitshinweise die an anderer Stelle diese Handbuchs enthalten sind nicht beachten kann das Verletzungen oder Sch den am Blade zur Folge haben Artesyn ist darauf bedacht alle notwendigen Informationen zum Einbau und zum Umgang mit dem Blade in diesem Handbuch bereit zu stellen Da es sich jedoch um ein komplexes Produkt mit vielf ltigen Einsatzm glichkeiten handelt k nnen wir die Vollst ndigkeit der im Handbuch enthaltenen Informationen nicht garantieren Falls Sie weitere Informationen ben tigen sollten wenden Sie sich bitte an die f r Sie zust ndige Gesch ftsstelle von Artesyn Das System erf llt die f r die Industrie geforderten Sicherheitsvorschriften und darf ausschlie lich f r Anwendungen in der Telekommunikationsindustrie und im Zusammenhang mit Industriesteuerungen verwendet werden Einbau Wartung und Betrieb d rfen nur von durch Artesyn ausgebildetem oder im Bereich Elektronik oder Elektrotechnik qualifiziertem Personal durchgef hrt werden Die in diesem Handbuch enthaltenen I
78. chaltkreisen Elektrostatische Entladung und unsachgem er Ein und Ausbau von Blades kann Schaltkreise besch digen oder ihre Lebensdauer verk rzen Bevor Sie Blades oder elektronische Komponenten ber hren vergewissern Sie sich da Sie in einem ESD gesch tzten Bereich arbeiten Datenverlust Wenn Sie das Blade aus dem Shelf herausziehen und die blaue LED blinkt noch gehen Daten verloren Warten Sie bis die blaue LED durchgehend leuchtet bevor Sie das Blade herausziehen Besch digung des Blades und von Zusatzmodulen Fehlerhafte Installation von Zusatzmodulen kann zur Besch digung des Blades und der Zusatzmodule f hren Lesen Sie daher vor der Installation von Zusatzmodulen die zugeh rige Dokumentation Besch digung des Blades Hohe Luftfeuchtigkeit und Kondensat auf der Oberfl che des Blades k nnen zu Kurzschl ssen f hren Betreiben Sie das Blade nur innerhalb der angegebenen Grenzwerte f r die relative Luftfeuchtigkeit und Temperatur Stellen Sie vor dem Einschalten des Stroms sicher dass sich auf dem Blade kein Kondensat befindet berhitzung und Besch digung des Blades Betreiben Sie das Blade ohne Zwangsbel ftung kann das Blade berhitzt und schlie lich besch digt werden Bevor Sie das Blade betreiben m ssen Sie sicher stellen dass das Shelf ber eine Zwangsk hlung verf gt Centellis 4100 Getting Started 6806800E1 8B 89 ATCA 7221 Sicherheitshinweise Wenn Sie das Blade in Gebieten mit stark
79. chlie en Sie nur serielle Ger te an die mit COM gekennzeichneten Stecker an Einige Varianten des Produktes sind Laserprodukte der Klasse 1 Um nicht sch dlicher Laserstrahlung ausgesetzt zu werden beachten Sie die folgenden Hinweise Anpassungen am Produkt die Bedienung von Steuerelementen sowie die Durchf hrung von Prozeduren d rfen nur gem den Anweisungen in diesem Dokument erfolgen Umweltschutz 100 Entsorgen Sie alte Batterien und oder Blades Systemkomponenten RTMs stets gem der in Ihrem Land g ltigen Gesetzgebung und den Empfehlungen des Herstellers Centellis 4100 Getting Started 6806800E18B RTM ATCA 7221 SCS Safety Notes 1 This section provides warnings that precede potentially dangerous procedures throughout this manual Instructions contained in the warnings must be followed during all phases of operation service and repair of this equipment You should also employ all other safety precautions necessary for the operation of the equipment in your operating environment Failure to comply with these precautions or with specific warnings elsewhere in this manual could result in personal injury or damage to the equipment Artesyn intends to provide all necessary information to install and handle the product in this manual Because of the complexity of this product and its various uses we do not guarantee that the given information is complete If you need additional information ask your Artesyn representative
80. ctive documentation Operation Board Damage Board surface High humidity and condensation on the board surface causes short circuits Do not operate the board outside the specified environmental limits Make sure the board is completely dry and there is no moisture on any surface before applying power Centellis 4100 Getting Started 6806800E1 8B 47 ATCA M100 Safety Notes Board Overheating and Board Damage Operating the board without forced air cooling may lead to board overheating and thus board damage When operating the board make sure that forced air cooling is available in the shelf Injuries or Short Circuits Board or power supply In case the ORing diodes of the board fail the board may trigger a short circuit between input line A and input line B so that line A remains powered even if it is disconnected from the power supply circuit and vice versa To avoid damage or injuries always check that there is no more voltage on the line that has been disconnected before continuing your work Hot Swap Installing the board into or removing it from a powered system not supporting hot swap or high availability causes board damage and data loss Therefore only install it in or remove it from a powered system if the system itself supports hot swap or high availability and if the system documentation explicitly includes guidelines RJ 45 Connector 48 The RJ 45 connector on the face plate must only be used for twisted pa
81. cure Then proceed to mount or service the system Personal Injury or System Damage When pulling the system out of the rack it can fall down and cause injuries Pull out the system cautiously Personal Injury or System Damage The system is heavy and if you carry it on your own you can hurt your back To prevent injury keep your back straight and have two people lift the system or use additional lifting equipment Centellis 4100 Getting Started 6806800E1 8B Centellis 4100 Shelf Safety Notes System Damage During the course of handling shipping and assembly pins shrouds and mounting screws blowers and other items can become loose or damaged Do not operate a damaged shelf this can cause damage to devices that interfere with it Electrical Hazard The caution label on the system s rear near the grounding studs shows that you have to create an earth connection because there may be a high leakage current which is considered as hazardous High leakage current can cause injuries Therefore it is essential that you create an earth connection before connecting the PEM Warning due to the high leakage current an earth connection is essential before connecting to a telecommuncation network Always ensure that the system is properly grounded System Damage Wrong jumper settings can make the shelf in operable Therefore never change the settings of the jumpers Blade and RTM Installation Damage of Circuits Electrosta
82. d steady pressure on the face plate as necessary to carefully slide the AMC module into the guides rails 6 Continue to gently push the module along the guide rails till the module is fully engaged with the connector Avoid using excessive force during this operation 7 Press module handle inwards towards the face plate to lock the AMC module on AMC bay 166 Centellis 4100 Getting Started 6806800E18B Installing the RTM ATCA 7221 FC 6 1 Before You Start This section provides the following information e Inspecting the contents of the delivered package Requirements 6 1 1 Package Inspection NOTICE Damage of Circuits Electrostatic discharge and incorrect RTM installation and removal can damage circuits or shorten their life Before touching the RTM or electronic components make sure that you are working in an ESD safe environment Shipment Inspection Procedure To inspect the shipment proceed as follows 1 Check that the RTM and this Installation Guide were shipped 2 Visually inspect the RTM for example ensure that all of the connector pins are straight If you observe damages report them to your local Artesyn sales representative 3 Remove the desiccant bag delivered together with the RTM and dispose of it according to your country s legislation 6 1 2 Requirements Before installing the RTM make sure the requirements described in this section are met Centellis 4100 Getting Started 68068
83. dingt in allen Phasen des Betriebs der Wartung und der Reparatur des Systems die Anweisungen die diesen Hinweisen enthalten sind Sie sollten au erdem alle anderen Vorsichtsma nahmen treffen die f r den Betrieb des Produktes innerhalb Ihrer Betriebsumgebung notwendig sind Wenn Sie diese Vorsichtsma nahmen oder Sicherheitshinweise die an anderer Stelle diese Handbuchs enthalten sind nicht beachten kann das Verletzungen oder Sch den am Produkt zur Folge haben Artesyn ist darauf bedacht alle notwendigen Informationen zum Einbau und zum Umgang mit dem Produkt in diesem Handbuch bereit zu stellen Da es sich jedoch um ein komplexes Produkt mit vielf ltigen Einsatzm glichkeiten handelt k nnen wir die Vollst ndigkeit der im Handbuch enthaltenen Informationen nicht garantieren Falls Sie weitere Informationen ben tigen sollten wenden Sie sich bitte an die f r Sie zust ndige Gesch ftsstelle von Artesyn Das System erf llt die f r die Industrie geforderten Sicherheitsvorschriften und darf ausschlie lich f r Anwendungen in der Telekommunikationsindustrie und im Zusammenhang mit Industriesteuerungen verwendet werden Einbau Wartung und Betrieb d rfen nur von durch Artesyn ausgebildetem oder im Bereich Elektronik oder Elektrotechnik qualifiziertem Personal durchgef hrt werden Die in diesem Handbuch enthaltenen Informationen dienen ausschlie lich dazu das Wissen von Fachpersonal zu erg nzen k nnen dieses jedoch nicht ersetzen
84. dpeererdsieaes 213 A 1 Artesyn Embedded Technologies Embedded Computing Documentation 213 A 2 Manufacturer s Documents 0 cece cece eee e eee nnn eee e eee eneeneennenne 214 AB Related Specifications ii wc vena en ae bates eas cane emis 215 Centellis 4100 Getting Started 6806800E18B 7 8 Centellis 4100 Getting Started 6806800E18B List of Tables ZZ a a Table 2 1 Environmental Conditions ssssesserrssssessseeesseseseseresrresesreos 119 Table 2 2 Critical Temperature Limits 0 cece cece eect eee erare tne aes 121 Table 2 3 System Power Requirements 0 cece cece e cece eee eee eee e eee e eee eeeaee 125 Table 2 4 Dimensions and Weight of System and Components ceeceeeeeeeeeeees 125 Table 4 1 Environmental Requirements 00 s cece cece een eee ene e cent nee neeeees 143 Table 5 1 Environmental Requirements cc cece eee cece e eee e eee nee eee ee ennees 149 Table 5 2 Critical Temperature Limits 2 cece eect nee eee nen etn ee eed 152 Table 5 3 DC System Power Requirements 0 cece eee cece e teen e eee e nee eenaeee 152 Table 5 4 Switch Settings u an Stand ced eee edd eee ed ae e dd Hed adae eames 154 Table 5 5 AMC Bay B4 Port Assignments 0 cece eee eee eee eee e eee een eens 161 Table 5 6 AMC Bay B1 Port Assignments 0 eee e eee eect eee e ene een eees 163 Table 6 2 Critical Temperature Limits
85. duktionsst tte in einwandfreiem Zustand befinden Verbogene Pins verursacht durch fehlerhafte Installation oder durch Installation von Boards mit besch digten Steckern kann die durch ECC gew hrte Garantie f r Boards und Backplanes erl schen lassen Centellis 4100 Getting Started 6806800E18B ATCA F120 Sicherheitshinweise Datenverlust Wenn Sie das Blade deinstallieren obwohl die blaue Hot Swap LED noch blinkt kann dies zu Datenverlust f hren Warten Sie daher bis die blaue LED durchgehend leuchtet bevor Sie das Blade deinstallieren Kabel und Stecker Besch digung des Blades Die R 45 Stecker an der Frontblende sind f r Anschl sse vom Typ Twisted Pair Ethernet TPE oder E1 T1 J1 vorgesehen Der Anschluss eines E1 T1 J1 Interfaces an einen Ethernet Stecker kann zur Zerst rung des Blades f hren Stellen Sie daher sicher dass TPE Stecker an Ihrem Arbeitsplatz eindeutig als Netzwerkstecker gekennzeichnet sind e Stellen Sie sicher dass die L nge eines Kabels welches an den RJ 45 Stecker angeschlossen ist 100 Meter nicht berschreitet e Stellen Sie sicher dass der TPE Stecker ausschliesslich mit einem Safety Extra Low Voltage Stromkreis SELV verbunden ist e Wenden Sie sich bei Fragen an ihren Systemadministrator Centellis 4100 Getting Started 6806800E18B 71 ATCA F120 Sicherheitshinweise AMC Module Besch digung von AMC Modulen Die zwei AMGSteckplatze sind ausschliesslich vorgesehen f r AMC Mod
86. e blade in the card guides of the shelf Ensure that the guiding module of shelf and blade are aligned properly 3 Apply equal and steady pressure to the blade to carefully slide the blade into the shelf until you feel resistance Continue to gently push the blade until the blade connectors engage 4 Squeeze the lever and the latch together and hook the lower and the upper handle into the shelf rail recesses Centellis 4100 Getting Started 6806800E18B 197 Installing the ATCA 7221 5 Fully insert the blade and lock it to the shelf by squeezing the lever and the latch together and turning the handles towards the face plate 6 Connect cables to the face plate if applicable 198 Centellis 4100 Getting Started 6806800E18B Starting up the System 9 1 Power Up Procedure Personal Injury through Electric Shock and Burning Touching the PEM power input terminals with metallic objects on your hands wrists or hanging from your neck may lead to amputations Do not wear any metallic attire or commodity on your hands wrists or hanging from your neck when working at the power input terminals or power input cables Be extremely careful when you use electrically conductive tools near the PEMs Short Circuit and Personal Injury through Electrical Shock Ensure that the power feeds you plan to remove or attach are powered off and cannot be switched on while you are working Ensure that all power input lines are not energized
87. e deformiert oder zerst rt werden Besch digung des RTMs oder Boards Das System wird besch digt wenn die RTMs nicht zu den von vorne in dem System installierten Boards passen Stellen Sie deshalb sicher dass Boards und RTMs die von vorne bzw von hinten in den gleichen Steckplatz des Systems eingebaut werden stets zueinander passen Datenverlust Das Entfernen eines RTMs w hrend des Systembetriebs und blinkender blauer LED des Front Boards f hrt zu Datenverlust Vor dem Entfernen des RTMs im laufenden Systembetrieb schalten Sie das entsprechende Board ab indem Sie die Griffe des Boards ffnen Warten Sie bis die blaue LED dauerhaft leuchtet Centellis 4100 Getting Started 6806800E18B Betrieb Centellis 4100 Shelf Sicherheitshinweise Fehlfunktion Unsachgem er Ein und Ausbau von Boards kann zu einer Fehlfunktion des Boards f hren Vergewissern Sie sich dass das Board ber alle Stecker an die AdvancedTCA Backplane angeschlossen und die Stromversorgung gew hrleistet ist berhitzung des Systems L ftungsschlitze Unzureichende L ftung kann Sch den an Boards und am System verursachen Um eine ausreichende L ftung zu gew hrleisten stellen Sie sicher dass das System w hrend des Betriebs stets waagerecht steht und dass ein Freiraum von mindestens 60mm an der R ckseite und mindestens 60mm an den Seiten des Systems vorhanden ist Halten Sie die L ftungsschlitze an der Oberseite der R ckseite und den Seiten d
88. e the shelf ground lug nut to maximum The studs are spaced 19 mm 0 75 inch apart This distance allows the use of anti rotating two hole lugs They are marked with the corresponding grounding symbol Artesyn recommends to use the cable from Thomas amp Betts as described in the chapter Tools You Will Need on page 134 or an equivalent cable 2 Permanently connect to the earth ground of the building Figure 3 2 Grounding Lugs at the System s Rear Z ESD Jack Grounding Lugs Centellis 4100 Getting Started 6806800E18B 139 Installing the System eee EEE 140 Centellis 4100 Getting Started 6806800E18B Chapter 4 Installing the RTM ATCA F120C 4 1 4 2 NOTICE Overview This chapter describes all necessary steps you need to take in order to install the Centellis 4100 The main steps are e Inspect the shipment and unpack the RTM Make sure environmental and power requirements are met e Install the RTM Unpacking and Inspecting the RTM Damage of Circuits Electrostatic discharge and incorrect installation and removal of the blade can damage circuits or shorten their life Before touching the blade or electronic components make sure that your are working in an ESD safe environment To inspect the shipment perform the following steps Shipment Inspection 1 Verify that you have received all items of your shipment Printed user manual Getting Started guide Centellis 4100 Centelli
89. ebenserhaltenden Ger ten oder in Flugzeugen verwendet werden Einbau Wartung und Betrieb d rfen nur von durch Artesyn ausgebildetem oder im Bereich Elektronik oder Elektrotechnik qualifiziertem Personal durchgef hrt werden Die in diesem Handbuch enthaltenen Informationen dienen ausschlie lich dazu das Wissen von Fachpersonal zu erg nzen k nnen dieses jedoch nicht ersetzen Halten Sie sich von stromf hrenden Leitungen innerhalb des Systems fern Entfernen Sie auf keinen Fall die Systemabdeckung Nur werksseitig zugelassenes Wartungspersonal oder anderweitig qualifiziertes Wartungspersonal darf die Systemabdeckung entfernen um Systemkomponenten zu ersetzen oder andere Anpassungen vorzunehmen Installieren Sie keine Ersatzteile oder f hren Sie keine unerlaubten Ver nderungen am System durch sonst verf llt die Garantie Wenden Sie sich f r Wartung oder Reparatur bitte an die f r Sie zust ndige Gesch ftsstelle von Artesyn So stellen Sie sicher dass alle sicherheitsrelevanten Aspekte beachtet werden Centellis 4100 Getting Started 6806800E18B 31 Centellis 4100 Shelf Sicherheitshinweise Allgemein EMV 32 Verletzungsgefahr An der R ckseite des Systems befinden sich spitze Stifte an denen Sie sich verletzen k nnen Seien Sie vorsichtig im Umgang mit dem System Das Produkt wurde getestet und erf llt die f r digitale Ger te der Klasse A g ltigen Grenzwerte gem den FCGRichtlinien Abschnitt 15 bzw EN 55022 Klas
90. emkomponenten f hren berpr fen Sie daher das RTM sowie die Backplane vor der Installation sorg ltig und stellen Sie sicher dass sich beide in einwandfreien Zustand befinden und keine Pins verbogen sind Centellis 4100 Getting Started 6806800E1 8B 79 RTM ATCA F120C Sicherheitshinweise Artesyn und unsere Zulieferer unternehmen gr te Anstrengungen um sicherzustellen dass sich Pins und Stecker von Blades RTMs vor dem Verlassung der Produktionsst tte in einwandfreiem Zustand befinden Verbogene Pins verursacht durch fehlerhafte Installation oder durch Installation von Blades RTMs mit besch digten Steckern kann die durch ECC gew hrte Garantie f r Blades und Backplanes erl schen lassen Kabel und Stecker Besch digung des Blades Die RJ 45 Stecker an der Frontblende sind f r Anschl sse vom Typ Twisted Pair Ethernet TPE oder E1 T1 1 vorgesehen Der Anschluss eines E1 T1 J1 Interfaces an einen Ethernet Stecker kann zur Zerst rung des Blades f hren Stellen Sie daher sicher dass TPE Stecker an Ihrem Arbeitsplatz eindeutig als Netzwerkstecker gekennzeichnet sind Stellen Sie sicher dass die L nge eines Kabels welches an den R 45 Stecker angeschlossen ist 100 Meter nicht berschreitet e Stellen Sie sicher dass der TPE Stecker ausschliesslich mit einem Safety Extra Low Voltage Stromkreis SELV verbunden ist e Wenden Sie sich bei Fragen an ihren Systemadministrator Umweltschutz Entsorgen Sie alte Batt
91. en Sie auf keinen Fall Abdeckungen am Produkt Nur werksseitig zugelassenes Wartungspersonal oder anderweitig qualifiziertes Wartungspersonal darf Abdeckungen entfernen um Komponenten zu ersetzen oder andere Anpassungen vorzunehmen Installieren Sie keine Ersatzteile oder f hren Sie keine unerlaubten Ver nderungen am Produkt durch sonst verf llt die Garantie Wenden Sie sich f r Wartung oder Reparatur bitte an die f r Sie zust ndige Gesch ftsstelle von Artesyn So stellen Sie sicher dass alle sicherheitsrelevanten Aspekte beachtet werden Centellis 4100 Getting Started 6806800E18B 77 RTM ATCA F120C Sicherheitshinweise EMV 78 Das Produkt wurde in einem Artesyn Standardsystem getestet Es erf llt die f r digitale Ger te der Klasse A g ltigen Grenzwerte in einem solchen System gem den FCCRichtlinien Abschnitt 15 bzw EN 55022 Klasse A Diese Grenzwerte sollen einen angemessenen Schutz vor St rstrahlung beim Betrieb des Produktes in Gewerbe sowie Industriegebieten gew hrleisten Das Produkt arbeitet im Hochfrequenzbereich und erzeugt St rstrahlung Bei unsachgem em Einbau und anderem als in diesem Handbuch beschriebenen Betrieb k nnen St rungen im Hochfrequenzbereich auftreten Warnung Dies ist eine Einrichtung der Klasse A Diese Einrichtung kann im Wohnbereich Funkst rungen verursachen In diesem Fall kann vom Betreiber verlangt werden angemessene Ma nahmen durchzuf hren Centellis 4100 Getting Started
92. environmental limits Make sure the blade is completely dry and there is no moisture on any surface before applying power Blade Overheating and Blade Damage Operating the blade without forced air cooling may lead to blade overheating and thus blade damage When operating the blade make sure that forced air cooling is available in the shelf 184 Centellis 4100 Getting Started 6806800E18B Installing the ATCA 7221 Table 8 1 Environmental Requirements Requirement Operating Non Operating Temperature 5 C 41 F to 40 C 104 F normal 40 C 40 F to 70 C 158 F operation according to NEBS Standard GR may be further limited by installed 63 CORE accessories 5 C 23 F to 55 C 131 F exceptional operation according to NEBS Standard GR 63 CORE All values may be further limited by installed accessories with more restrictive environmental requirements Temp 0 25 C min according to NEBS Standard 0 25 C min Change GR 63 CORE Rel Humidity 5 to 95 non condensing according to 5 to 95 non condensing Artesyn internal environmental requirements according to Artesyn internal environmental requirements Altitude Up to 3 000 m Up to 12 000 m Vibration 5 20 Hz 0 5 mm amplitude 1 mm amplitude 20 250 Hz 1g 2 0g Shock 5 g 11 ms halfsine according to Artesyn 15 g 11 ms half sine according to internal environmental requirements Artesyn internal environmental
93. er Verkabelung ob das System ordnungsgem arbeitet Reduzieren Sie die Verletzungsgefahr indem Sie Kabel so verlegen dass niemand dar ber stolpern kann Centellis 4100 Getting Started 6806800E1 8B 41 Centellis 4100 Shelf Sicherheitshinweise Verletzungsgefahr durch Stromschlag Durch das Ber hren von Kontakten und Kabeln w hrend des Betriebs k nnen Sie einen elektrischen Schlag bekommen Schlie en Sie in jedem Fall aus dass Personen durch einen elektrischen Schlag verletzt werden k nnen indem Sie sicherstellen dass Kontakte und Kabel des Systems w hrend des Betriebs nicht ber hrt werden k nnen Falls Sie Fragen bez glich der Verkabelung haben wenden Sie sich an die f r Sie zust ndige Gesch ftsstelle von Artesyn Besch digung der Kabel Werden Kabel geknickt kann das Kabel besch digt werden und der Datentransfer nicht mehr stattfinden Stellen Sie sicher dass Kabel nicht geknickt werden RJ 45 Stecker Besch digung des Systems Bei den RJ 45 Steckern die sich auf den Boards befinden handelt es sich entweder um Twisted Pair Ethernet TPE oder um E1 T1 J1 Stecker Beachten Sie dass ein versehentliches Anschlie en einer E1 T1 1 Leitung an einen TPE Stecker Ihr System zerst ren kann e Kennzeichnen Sie deshalb TPE Anschliisse in der N he Ihres Arbeitsplatzes deutlich als Netzwerkanschl sse e Stellen Sie sicher dass die L nge eines mit Ihrem Systems verbundenen TPE Kabels 100 m nicht berschreitet
94. er elektromagnetischer Strahlung betreiben stellen Sie sicher dass das Blade mit dem System verschraubt ist und das System durch ein Geh use abgeschirmt wird 90 Centellis 4100 Getting Started 6806800E18B ATCA 7221 Sicherheitshinweise Verletzungen oder Kurzschliisse Blade oder Stromversorgung Falls die ORing Dioden des Blades durchbrennen kann das Blade einen Kurzschluss zwischen den Eingangsleitungen A und B verursachen In diesem Fall ist Leitung A immer noch unter Spannung auch wenn sie vom Versorgungskreislauf getrennt ist und umgekehrt Pr fen Sie deshalb immer ob die Leitung spannungsfrei ist bevor Sie Ihre Arbeit fortsetzen um Sch den oder Verletzungen zu vermeiden Schaltereinstellungen Fehlfunktion des Blades Schalter die mit Reserved gekennzeichnet sind k nnen mit produktionsrelevanten Funktionen belegt sein Das ndern dieser Schalter kann im normalen Betrieb St rungen ausl sen Verstellen Sie nur solche Schalter die nicht mit Reserved gekennzeichnet sind Pr fen und ndern Sie die Einstellungen der nicht mit Reserved gekennzeichneten Schalter bevor Sie das Blade installieren Besch digung der Blade Das Verstellen von Schaltern w hrend des laufenden Betriebes kann zur Besch digung des Blades f hren Pr fen und ndern Sie die Schaltereinstellungen bevor Sie das Blade installieren PMC Module Begrenzte Leistung auf dem PMC Modul und RTM Das Blade verfuegt ueber keine Sicherung fuer
95. erface with dual star interconnect Base interface to the shelf manager slots Update interface between physical adjacent slots Bused IPMB 0 connections Synchronization clock buses 1 2 3 Shelf Manager The shelf manager ATCA M100 is designed to be used in AdvancedTCA systems It is the central management unit of the shelf Its purpose is to monitor control and assure proper operation of the shelf and all other components of the AdvancedTCA shelf It reports anomalies and errors and takes corrective actions if required for example increase the speed of the blowers The ATCA M100 has access to detailed inventory information as well as sensor status information of the shelf and all components of the shelf The ATCA M100 is fully compliant to the shelf management functions as specified in the PICMG 3 0 R1 0 Specification For a detailed description refer to the ATCA M100 Installation and Use and the System Management Interface Based on HPI B Centellis 31kX 4100 User s Guide Centellis 4100 Getting Started 6806800E18B 113 Introduction 1 2 4 Node Slots The backplane in a Centellis 4100 system provides 12 node slots They are located to the left and to the right of the two hub slots in the middle Figure 1 3 Slot Distribution Physical Slots 1 23 4 5 6 7 8 9 10 11 12 13 14 v D amp a v Oo fe Zz Node Blade Node Blade Node Blade Node Blade Node Blade Node Blade Node Blade Node Blade Node Blade Node Blade
96. erien und oder Blades Systemkomponenten RTMs stets gem der in Ihrem Land g ltigen Gesetzgebung wenn m glich immer umweltfreundlich 80 Centellis 4100 Getting Started 6806800E18B ATCA 7221 Safety Notes EMC This section provides warnings that precede potentially dangerous procedures throughout this manual Instructions contained in the warnings must be followed during all phases of operation service and repair of this equipment You should also employ all other safety precautions necessary for the operation of the equipment in your operating environment Failure to comply with these precautions or with specific warnings elsewhere in this manual could result in personal injury or damage to the equipment Artesyn intends to provide all necessary information to install and handle the product in this manual Because of the complexity of this product and its various uses we do not guarantee that the given information is complete If you need additional information ask your Artesyn representative The product has been designed to meet the standard industrial safety requirements It must not be used except in its specific area of office telecommunication industry and industrial control Only personnel trained by Artesyn or persons qualified in electronics or electrical engineering are authorized to install remove or maintain the product The information given in this manual is meant to complete the knowledge of a specialist and must n
97. es 147 5 3 Environmental and Power Requirements ccc cece e cece eee e ee eeeeeeneees 148 5 3 1 Environmental Requirements ccc cece een eee e eee ene ee ne eeneees 148 5 3 2 Power Requirements eu ns ne ne 152 5 4 Configuring the Blade cece ccc ccc cece cect e tenn nee e ne nenn nennen nenn 152 5 5 Blade Installation rss 2 0 panded cris doe Ponsa ea oe ee 155 5 5 1 Installing the Blade 0 cece cence nen eee nena tena eeneees 156 5 6 AMEM d les nes een enteo sn able 159 5 6 1 Supported AMC Modules 0 cece cece ence nee e eee ene tence eenenes 161 5 6 1 1 AMC Bay B4 ea ee wees es 161 5 6 1 2 AMC Bay BI u ee em 162 5 6 2 AMC Module Installation 00 c cece een cen een e ene eee e nennen 165 installing the RTM ATCA 722 1 FC un ictetseusneteoteuewedewebwsteeeeee 167 6 1 Before You Starts c2d ee ee a an 167 6 1 1 Package InspectiOn cece ccc ccc cece eee ene een e teen ne nenn tenes 167 6 1 2 Requirements sets en 167 6 1 2 1 PowerRequirements ccc e cece tritri dtii eres ee kERES 168 6 1 2 2 Environmental Requirements 0 cece eee eee eee eee eee e es 168 6 2 Module Installation 0 eect nen nent e teen tne e ee tneeaed 171 6 2 1 InstallingtheiRTM re nn re ee nenn 172 7 Installing the RTM ATCA 7221 SCS 00ssssssnnnenenennnnen nennen nennen nn 175 7 1 Before You Start u tens ee ne Den 175 7 1 1 Package
98. es Systems frei Halten Sie die Frischluftzufuhr ffnung an der unteren Vorderseite des Systems v llig frei und stellen Sie sicher dass sich die Frischluft nicht mit der Abluft von anderen Systemen mischt Um eine ungest rte Luftzirkulation zu gew hrleisten stellen Sie sicher dasss alle Steckpl tze mit Boards oder Platzhaltern belegt sind Besch digung des Systems Durch hohe Luftfeuchtigkeit k nnen Kurzschl sse entstehen Betreiben Sie das System nur innerhalb der angegebenen Grenzwerte f r die relative Luftfeuchtigkeit und Temperatur Stellen Sie vor dem Einschalten des Stroms sicher dass sich auf dem System und auf den Boards kein Kondensat befindet und starten Sie das System nicht unter 0 C Stromschlaggefahr Das System besitzt zwei oder vier 48V bis 60V DC Anschl sse Alle Anschl sse m ssen vom System entfernt werden um das System spannungsfrei zu schalten Um eine Verletzungsgefahr zu minimieren entfernen Sie die Anschl sse wenn Sie das System ausschalten Besch digung des Systems Luftfilter Verunreinigungen in der Luft k nnen den Luftfilter verschmutzen und so die Luftzufuhr des Centellis 4100 Getting Started 6806800E1 8B 37 Centellis 4100 Shelf Sicherheitshinweise 38 Systems beeintr chtigen Das kann zur berhitzung des Systems und zu Sch den an Systemteilen f hren Um einen reibungslosen Luftstrom durch das System zu gew hrleisten sollten Sie den Luftfilter sp testens alle sechs Monate austau
99. ese Grenzwerte sollen einen angemessenen Schutz vor St rstrahlung beim Betrieb des Blades in Gewerbe sowie Industriegebieten gew hrleisten Das Board arbeitet im Hochfrequenzbereich und erzeugt St rstrahlung Bei unsachgem em Einbau und anderem als in diesem Handbuch beschriebenen Betrieb k nnen St rungen im Hochfrequenzbereich auftreten Centellis 4100 Getting Started 6806800E18B 59 SPARE ATCA A100 Sicherheitshinweise Installation Betrieb Elektrostatische Entladung und unsachgem er Ein und Ausbau des Boards kann Schaltkreise besch digen oder ihre Lebensdauer verk rzen Beachten Sie deshalb die folgenden Punkte e Ber hren Sie das Board oder elektrische Komponenten in einem nicht ESD gesch tzten Bereich kann dies zu einer Besch digung des Boards f hren Bevor Sie Boards oder elektronische Komponenten ber hren vergewissern Sie sich dass Sie in einem ESD gesch tzten Bereich arbeiten e Falls das Board als Teil eines Systems ausgeliefert wird tauschen Sie keine Verkabelungen des Boards aus es sei denn es ist in der Systemdokumentation ausdr cklich erw hnt Achten Sie darauf dass die Umgebungs und die Leistungsanforderungen w hrend des Betriebs eingehalten werden Betreiben Sie das Board nur innerhalb der angegebenen Grenzwerte f r die relative Luftfeuchtigkeit und Temperatur da durch hohe Luftfeuchtigkeit Kurzschl sse entstehen k nnen Stellen Sie vor dem Einschalten des Stroms sicher dass sich auf
100. eseitigt werden m ssen nderungen oder Modifikationen am Produkt welche ohne ausdr ckliche Genehmigung von Artesyn durchgef hrt werden k nnen dazu f hren dass der Anwender die Genehmigung zum Betrieb des Produktes verliert Boardprodukte werden in einem repr sentativen System getestet um zu zeigen dass das Board den oben aufgef hrten EMV Richtlinien entspricht Eine ordnungsgem e Installation in einem System welches die EMV Richtlinien erf llt stellt sicher dass das Produkt gem den EMV Richtlinien betrieben wird Verwenden Sie nur abgeschirmte Kabel zum Anschluss von Zusatzmodulen So ist sichergestellt dass sich die Aussendung von Hochfrequenzstrahlung im Rahmen der erlaubten Grenzwerte bewegt Warnung Dies ist eine Einrichtung der Klasse A Diese Einrichtung kann im Wohnbereich Funkst rungen verursachen In diesem Fall kann vom Betreiber verlangt werden angemessene Ma nahmen durchzuf hren Board Installation 52 Bevor Sie das Board in einem System installieren berpr fen Sie ob die im Kapitel Board Exchange aufgef hrten Anforderungen erf llt werden Bereich mit eingeschr nkter Zugang Installieren Sie das Board in ein System nur in Bereichen mit eingeschr nktem Zugang Centellis 4100 Getting Started 6806800E18B ATCA M100 Sicherheitshinweise Betrieb Datenverlust Ziehen Sie das Board im laufenden Betrieb heraus obwohl die Hot Swap LED noch nicht leuchtet f hrt das zu Datenverlust War
101. ever and the latch together and hook the lower and the upper handle into the shelf rail recesses 172 Centellis 4100 Getting Started 6806800E18B Installing the RTM ATCA 7221 FC 7 Fully insert the RTM and lock it to the shelf by pressing the two components of the lower and the upper handles together and turning the handles toward the face plate 8 Tighten both face plate screws on the RTM Centellis 4100 Getting Started 6806800E18B 173 Installing the RTM ATCA 7221 FC eee O 174 Centellis 4100 Getting Started 6806800E18B Installing the RTM ATCA 7221 SCS A 7 1 Before You Start This section provides the following information e Inspecting the contents of the delivered package Requirements 7 1 1 Package Inspection NOTICE Damage of Circuits Electrostatic discharge and incorrect RTM installation and removal can damage circuits or shorten their life Before touching the RTM or electronic components make sure that you are working in an ESD safe environment Shipment Inspection Procedure To inspect the shipment proceed as follows 1 Check that the RTM and this Installation Guide were shipped 2 Visually inspect the RTM for example ensure that all of the connector pins are straight If you observe damages report them to your local Artesyn sales representative 3 Remove the desiccant bag delivered together with the RTM and dispose of it according to your country s legislation 7 1 2
102. fault settings The switches are displayed as the small white squares 152 Centellis 4100 Getting Started 6806800E18B Installing the ATCA F120 On Board Configuration Switches Figure 5 2 153 Centellis 4100 Getting Started 6806800E18B Installing the ATCA F120 Blade Malfunction Switches marked as reserved might carry production related functions and can cause the blade to malfunction if their setting is changed Therefore do not change settings of switches marked as reserved The setting of switches which are not marked as reserved has to be checked and changed before blade installation Blade Damage Setting resetting the switches during operation can cause blade damage Therefore check and change switch settings before you install the blade Table 5 4 Switch Settings Switch Description SW1 1 Selects whether the shelf manager ShM is accessed through Base Channel port 1 or Update channel port 0 Note that this switch setting can be overwritten via IPMI OFF ShM is accessed through Update Channel port 0 default ON ShM is accessed through Base Channel port 1 SW1 2 Reserved default OFF SW1 3 Reserved default OFF SW1 4 Reserved default OFF SW2 1 Reserved default OFF SW2 2 Reserved default OFF SW2 3 User flash 1 write
103. from time to time in the content hereof without obligation of Artesyn to notify any person of such revision or changes Electronic versions of this material may be read online downloaded for personal use or referenced in another document as a URL to an Artesyn website The text itself may not be published commercially in print or electronic form edited translated or otherwise altered without the permission of Artesyn It is possible that this publication may contain reference to or information about Artesyn products machines and programs programming or services that are not available in your country Such references or information must not be construed to mean that Artesyn intends to announce such Artesyn products programming or services in your country Limited and Restricted Rights Legend If the documentation contained herein is supplied directly or indirectly to the U S Government the following notice shall apply unless otherwise agreed to in writing by Artesyn Use duplication or disclosure by the Government is subject to restrictions as set forth in subparagraph b 3 of the Rights in Technical Data clause at DFARS 252 227 7013 Nov 1995 and of the Rights in Noncommercial Computer Software and Documentation clause at DFARS 252 227 7014 Jun 1995 Contact Address Artesyn Embedded Technologies Artesyn Embedded Technologies Marketing Communications Lilienthalstr 17 19 2900 S Diablo Way Suite 190 85579 Neubiberg Munich
104. handles of the RTM are in an outward position by squeezing the lever and the latch together 3 Insert the RTM into the shelf by placing the top and bottom edges in the card guides of the slot 4 Slide the RTM into the slot 5 Apply equal and steady pressure to the RTM to carefully slide the RTM into the shelf until you feel resistance Continue to gently push the RTM until the RTM connectors engage 6 Squeeze the lever and the latch together and hook the lower and the upper handle into the shelf rail recesses 180 Centellis 4100 Getting Started 6806800E18B Installing the RTM ATCA 7221 SCS 7 Fully insert the RTM and lock it to the shelf by pressing the two components of the lower and the upper handles together and turning the handles toward the face plate 8 Tighten both face plate screws on the RTM Centellis 4100 Getting Started 6806800E18B 181 Installing the RTM ATCA 7221 SCS eee EEE 182 Centellis 4100 Getting Started 6806800E18B Installing the ATCA 7221 8 1 Unpacking and Inspecting the Blade NOTICE Damage of Circuits Electrostatic discharge and incorrect blade installation and removal can damage circuits or shorten their life Before touching the blade or electronic components make sure that you are working in an ESD safe environment Shipment Inspection To inspect the shipment perform the following steps 1 Verify that you have received all items of your shipment ATCA 7221
105. he rack If other systems are installed in one rack start with the heaviest component at the bottom If the rack is equipped with stabilizing devices make sure that they are installed and extended so that the rack is secure Then proceed to mount or service the system 126 Centellis 4100 Getting Started 6806800E18B Site Preparation NOTICE During the course of handling shipping and assembly pins shrouds and mounting screws blowers and other items can become loose or damaged Do not operate a damaged shelf this can cause damage to devices that interfere with it Grounding To ensure the system is properly grounded each of the system s parts contact the EMI gasket The system contains gaskets at the shelf and module level The shelf is also fitted with ESD contacts Please take care for proper ESD protection of the operator Centellis 4100 Getting Started 6806800E18B 127 Site Preparation You have to keep the following conditions when installing the system into a600 mm 23 62 inch deep rack The physical dimensions in the figure below are in millimeters Figure 2 4 Rack Mounting Dimensions Air outlet Rear PEM protective cover 600 mm deep rack 2 2 6 Airflow Requirements The Centellis 4100 provides fault tolerant cooling to front mounted AdvancedTCA blades and to rear transition modules based on four front maintainable intelligent blower trays with one blower per tray 128 Ce
106. he standoffs delivered with the blade on the standoffs of the PMC 2 Connect PMC module carefully to PMC slot 3 Make sure that standoffs of PMC module cover mounting holes of the blade Centellis 4100 Getting Started 6806800E18B 195 Installing the ATCA 7221 4 Place screws delivered with PMC module into mounting holes 5 Fasten screws 8 5 Blade Installation The blade is fully compatible to the AdvancedTCA standard and is designed to be used in AdvancedTCA shelves The blade can be installed in any AdvancedTCA node slot NOTICE Damage of Circuits Electrostatic discharge and incorrect blade installation and removal can damage circuits or shorten their life Before touching the blade or electronic components make sure that you are working in an ESD safe environment Blade Malfunctioning Incorrect blade installation and removal can result in blade malfunctioning When plugging the blade in or removing it do not press on the face plate but use the handles 8 5 1 Installing the Blade To install the blade into an AdvancedTCA shelf proceed as follows 196 Centellis 4100 Getting Started 6806800E18B Installing the ATCA 7221 Installation Procedure Follow the following steps to install the blade 1 Ensure that the top and bottom ejector handles are in the outward position by squeezing the lever and the latch together 2 Insert blade into the shelf by placing the top and bottom edges of th
107. hich type of AMC modules are supported for each AMC bay Furthermore the installation removal procedure for AMC modules will be given This procedure is identical for all AMC modules in both AMC bays 5 6 1 Supported AMC Modules The AMC bays AMC B4 and AMC B1 are designed to support different types of AMC modules Both AMC bays are compliant to AMC 0 R2 0 tz Consult your local Artesyn sales representative for a list of AMC modules which Artesyn has NAN validated for the use in AMC B1 and AMC B4 5 6 1 1 AMC Bay B4 This AMC bay is designed to support Artesyn processor AMC modules The following table describes how the AMC ports are assigned Table 5 5 AMC Bay B4 Port Assignments Connector Region AMC Port Usage on ATCA F120 Clocking 1 Unused 2 Unused 3 PCI Express HCSL 100 MHz clock Common Options 0 AdvancedTCA update channel port 2 3 _ AdvancedTCA update channel port 4 AMC Bay B1 port 2 AMC Bay B1 port 3 AMC Bay B1 port 4 AMC Bay B1 port 5 AMC Bay B1 port 6 AMC Bay B1 port 7 Fat Pipes NIE OD wo BR WIN Centellis 4100 Getting Started 6806800E18B 161 Installing the ATCA F120 Table 5 5 AMC Bay B4 Port Assignments continued Connector Region AMC Port Usage on ATCA F120 8 Ethernet Dual MAC Intel 8267 1EB 9 Ethernet Dual MAC Intel 82671EB 10 Ethernet Dual MAC Intel 82671EB 11 Ethernet Dual MAC Intel 82671EB Extended
108. iehen herunterfallen und Verletzungen verursachen Ziehen Sie das System vorsichtig heraus damit es nicht herunterf llt Verletzungsgefahr oder Besch digung des Systems Centellis 4100 Getting Started 6806800E18B Centellis 4100 Shelf Sicherheitshinweise Das System ist schwer und wenn Sie es alleine tragen kann dies zu R ckensch den f hren Heben Sie deshalb das System nur zu zweit und halten Sie beim Heben Ihren R cken gerade oder benutzen Sie zus tzliche Hilfsmittel Besch digung des Systems W hrend des Transportes und Zusammenbaus des Systems k nnen sich Teile wie zum Beispiel Schrauben Stecker oder L fter l sen oder besch digt werden Nehmen Sie das System nicht in Betrieb wenn Teile besch digt sind Dies k nnte zu Besch digungen an anderen Teilen f hren Hoher Ableitstrom Dieser Aufkleber befindet sich in der N he der Schuzleiter auf der R ckseite des Systems und warnt dass Sie vor der Inbetriebnahme eine Erdung durchf hren m ssen da hier ein hoher Ableitstrom vorhanden sein kann Hoher Ableitstrom kann zu Verletzungen f hren Stellen Sie deshalb vor Anschluss des Systems an den Versorgungsstromkreis unbedingt eine Erdungsverbindung her Besch digung des Systems Falsche Jumper Einstellungen k nnen dazu f hren dass das System nicht mehr funktioniert ndern Sie deshalb nie die Einstellungen der Jumper Board und RTM Installation Besch digung des Boards Ber hren Sie das Board oder elekt
109. ings that precede potentially dangerous procedures throughout this manual Instructions contained in the warnings must be followed during all phases of operation service and repair of this equipment You should also employ all other safety precautions necessary for the operation of the equipment in your operating environment Failure to comply with these precautions or with specific warnings elsewhere in this manual could result in personal injury or damage to the equipment Artesyn intends to provide all necessary information to install and handle the product in this manual Because of the complexity of this product and its various uses we do not guarantee that the given information is complete If you need additional information ask your Artesyn representative The product has been designed to meet the standard industrial safety requirements It must not be used except in its specific area of office telecommunication industry and industrial control Only personnel trained by Artesyn or persons qualified in electronics or electrical engineering are authorized to install remove or maintain the product The information given in this manual is meant to complete the knowledge of a specialist and must not be used as replacement for qualified personnel Keep away from live circuits inside the equipment Operating personnel must not remove equipment covers Only factory authorized service personnel or other qualified service personnel may remove eq
110. ional blades or modules make sure that the power consumption of all SN _ installed modules does not exceed the system s maximum power dissipation 2 2 4 Dimensions and Weight The table below lists the dimensions and weight of the shelf and system components N N gt The maximum weight of the system must not exceed 80 kg Table 2 4 Dimensions and Weight of System and Components Dimensions Component wxhxdinmm Weight in kg Shelf including four blowers four PEMs air filter 483x575x505 34 00 PEM 69 x 102 x 138 0 96 Blower 210x42x215 1 72 Centellis 4100 Getting Started 6806800E18B 125 Site Preparation Table 2 4 Dimensions and Weight of System and Components continued Dimensions Component wxhxdinmm Weight in kg ATCA M100 20x 102x117 0 13 ATCA F120 30x 351x312 2 30 RTM ATCA F1 20 322 25x70 0 70 ATCA 7221 30x351x312 3 20 2 2 5 Mounting Options You can simply operate the system on your desk or you can install it ina standard 19 rack Personal Injury or System Damage The system is heavy and if you carry it on your own you can hurt your back To prevent injury keep your back straight and have two people lift the system or use additional lifting equipment Personal or System Damage Unstable system installation in a rack can cause the rack to topple over Therefore if your system is the only one in the rack make sure to mount the system in the lowest part of t
111. ir Ethernet TPE connections Connecting a telephone to such a connector may destroy your telephone as well as your board Therefore Clearly mark TPE connectors near your working area as network connectors e Only connect TPE bushing of the system to safety extra low voltage SELV circuits Make sure that the length of the electric cable connected to a TPE bushing does not exceed 100 m If you have further questions ask your system administrator Centellis 4100 Getting Started 6806800E1 8B ATCA M100 Safety Notes Replacement Expansion Only replace or expand components or system parts with those recommended by Artesyn Otherwise you are fully responsible for the impact on EMC or any possible malfunction of the product Check the total power consumption of all components installed see the technical specification of the respective components Ensure that any individual output current of any source stays within its acceptable limits see the technical specification of the respective source Environment Always dispose of used products according to your country s legislation and manufacturer s instructions Centellis 4100 Getting Started 6806800E1 8B 49 ATCA M100 Safety Notes eee EEE 50 Centellis 4100 Getting Started 6806800E18B ATCA M100 Sicherheitshinweise SS Dieses Kapitel enthalt Hinweise die potentiell gefahrlichen Prozeduren innerhalb dieses Handbuchs vorrangestellt sind Beachten Sie unbe
112. ircuits or shorten their life Before touching the blade or electronic components make sure that you are working in an ESD safe environment Damage of the blade Incorrect installation of the blade can cause damage of the blade Only use handles when installing removing the blade to avoid damage deformation to the face plate and or PCB 5 5 1 Installing the Blade To install the blade into an AdvancedTCA shelf proceed as follows 156 Centellis 4100 Getting Started 6806800E18B Installing the ATCA F120 Installation Procedure The following procedure describes the installation of the blade It assumes that your system is powered If your system is unpowered you can disregard the blue LED and thus skip the respective step In this case it is a purely mechanical installation 1 Ensure that the top and bottom ejector handles are in the outward position by squeezing the lever and the latch together 2 Insert blade into the shelf by placing the top and bottom edges of the blade in the card guides of the shelf Ensure that the guiding module of shelf and blade are aligned properly 3 Apply equal and steady pressure to the blade to carefully slide the blade into the shelf until you feel resistance Continue to gently push the blade until the blade connectors engage 4 Squeeze the lever and the latch together and hook the lower and the upper handle into the shelf rail recesses Centellis 4100 Getting Started 6
113. ith built in speed control Air Filter The air filter is located in the lower part of the shelf It ensures that the shelf operates efficiently and therefore regular replacing is required Centellis 4100 Getting Started 6806800E18B 115 Introduction ee SER DES an nn 116 Centellis 4100 Getting Started 6806800E18B Site Preparation Chapter 2 2 1 Overview The following sections help you to prepare system installation Section Site Planning Considerations Gives Information On This section includes information on unpacking and inspecting the system requirements technical data and other information you need to know before you start system installation Site Planning Checklists This section provides checklists for site preparation 2 2 Site Planning Considerations This section provides information to prepare the site and the shelf for installation 2 2 1 Receiving and Unpacking the System Carefully inspect the system and all components delivered together with it NOTICE Damage of Circuits shorten their life ESD safe environment Electrostatic discharge and incorrect RTM installation and removal can damage circuits or Before touching the RTM or electronic components make sure that you are working in an Shipment Inspection To inspect the shipment perform the following steps 1 Verify that you have received all items of your shipment Compare the shipment thorough
114. kein Kondensat befindet und betreiben Sie das Blade nicht unter 5 C berhitzung und Besch digung des Blades Betreiben Sie das Blade ohne Zwangsbel ftung kann das Blade berhitzt und schlie lich besch digt werden Bevor Sie das Blade betreiben m ssen Sie sicher stellen dass das Shelf ber eine Zwangsk hlung verf gt Verletzungen oder Kurzschl sse Blade oder Stromversorgung Falls die ORing Dioden des Blades durchbrennen kann das Blade einen Kurzschluss zwischen den Eingangsleitungen A und B verursachen In diesem Fall ist Leitung A immer noch unter Spannung auch wenn sie vom Versorgungskreislauf getrennt ist und umgekehrt Pr fen Sie deshalb immer ob die Leitung spannungsfrei ist bevor Sie Ihre Arbeit fortsetzen um Sch den oder Verletzungen zu vermeiden Schaltereinstellungen Jumper Fehlfunktion des Blades Schalter die mit Reserved gekennzeichnet sind k nnen mit produktionsrelevanten Funktionen belegt sein Das ndern dieser Schalter kann im normalen Betrieb St rungen ausl sen Verstellen Sie nur solche Schalter die nicht mit Reserved gekennzeichnet sind Pr fen und ndern Sie die Einstellungen der nicht mit Reserved gekennzeichneten Schalter bevor Sie das Blade installieren Besch digung der Blade Centellis 4100 Getting Started 6806800E18B 69 ATCA F120 Sicherheitshinweise Das Verstellen von Schaltern w hrend des laufenden Betriebes kann zur Besch digung des Blades f hren Pr fen u
115. le anderen Vorsichtsma nahmen treffen die f r den Betrieb des Produktes innerhalb Ihrer Betriebsumgebung notwendig sind Wenn Sie diese Vorsichtsma nahmen oder Sicherheitshinweise die an anderer Stelle diese Handbuchs enthalten sind nicht beachten kann das Verletzungen oder Sch den am Produkt zur Folge haben Artesyn ist darauf bedacht alle notwendigen Informationen zum Einbau und zum Umgang mit dem Produkt in diesem Handbuch bereit zu stellen Da es sich jedoch um ein komplexes Produkt mit vielf ltigen Einsatzm glichkeiten handelt k nnen wir die Vollst ndigkeit der im Handbuch enthaltenen Informationen nicht garantieren Falls Sie weitere Informationen ben tigen sollten wenden Sie sich bitte an die f r Sie zust ndige Gesch ftsstelle von Artesyn Das System erf llt die f r die Industrie geforderten Sicherheitsvorschriften und darf ausschlie lich f r Anwendungen in der Telekommunikationsindustrie und im Zusammenhang mit Industriesteuerungen verwendet werden Einbau Wartung und Betrieb d rfen nur von durch Artesyn ausgebildetem oder im Bereich Elektronik oder Elektrotechnik qualifiziertem Personal durchgef hrt werden Die in diesem Handbuch enthaltenen Informationen dienen ausschlie lich dazu das Wissen von Fachpersonal zu erg nzen k nnen dieses jedoch nicht ersetzen Halten Sie sich von stromf hrenden Leitungen innerhalb des Produktes fern Entfernen Sie auf keinen Fall Abdeckungen am Produkt Nur werksseitig zugelassene
116. lified service personnel may remove equipment covers for internal subassembly or component replacement or any internal adjustment Do not install substitute parts or perform any unauthorized modification of the equipment or the warranty may be voided Contact your local Artesyn representative for service and repair to make sure that all safety features are maintained Electrical Interference This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Centellis 4100 Getting Started 6806800E1 8B 73 RTM ATCA F120C Safety Notes Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Changes or modifications not expressly approved by Artesyn could void the user s authority to operate the equipment Board products are tested in a representative system to show compliance with the above mentioned requirements A proper installation in a compliant system will maintain the required performance Use only shielded cables
117. llispedion a aussehen aba 175 7 12 Requirements ee Beben 175 7 1 2 1 Environmental Requirements 2 ccc cece e eee eee eee eneees 176 1 1 2 2 Power Requirements u a 178 7 1 2 3 Backplane Requirements 0 cece cece eee ene ee nennen 178 7 2 Module installation u een ee 179 7 2 1 InstallingtheRTM u su sen ee nenne 180 8 Installing the ATCA 7221 2 un a detedeteeiegeeareeeeeeeentes 183 8 1 Unpacking and Inspecting the Blade cece cece cece cence teen nen en nen 183 82 Requirements nn en 183 8 2 1 Environmental Requirements 0 e cece eee ene eee eee e ee nennen 184 8 2 2 Power Requirements oe eens ee ee EEEREN 188 8 3 Switch Settings tesa leben erh nn eee ada 189 8 4 PMCModul dcciacigiededs 22 ek ik pe OER 194 8 5 Blade liistallation u sn em en Die nl 196 8 5 1 Installing the Blade 1 keene nent nent eeneeeneees 196 9 Startinglup the Systemics aus nd 199 9 1 PowerFUp Procedure u a ae nn dd ine ake ren ehel 199 10 System Sollware ecke 207 10 1 SOVENVIEW an een ee ae ee en Boni ee 207 10 2 Available SoftWare un en ee u 207 10 3 Supported Operating Systems 0 cece cece cece ence ene ene seen nennen 208 6 Centellis 4100 Getting Started 6806800E1 8B eee EEE 10 4 lnstallation 4er 832 bees vee he dee Rhone oie baw elles EEEO eee nes 208 10 5 Upgrade ee een each ee 209 A Related Documentation 4 4 Ba Reeesdseaear
118. ly acceptable way 58 Centellis 4100 Getting Started 6806800E18B SPARE ATCA A100 Sicherheitshinweise Dieser Abschnitt enth lt Sicherheitshinweise die bei Einbau Betrieb und Wartung des Boards zu beachten sind Wir sind darauf bedacht alle notwendigen Informationen die f r die Installation und den Betrieb erforderlich sind in diesem Handbuch bereit zu stellen Da es sich jedoch um ein komplexes Produkt mit vielf ltigen Einsatzm glichkeiten handelt k nnen wir die Vollst ndigkeit der im Handbuch enthaltenen Informationen nicht garantieren Falls Sie weitere Informationen ben tigen sollten wenden Sie sich bitte an die f r Sie zust ndige Gesch ftsstelle von Artesyn Das Board erf llt die f r die Industrie geforderten Sicherheitsvorschriften und darf ausschlie lich f r Anwendungen in der Telekommunikationsindustrie und im Zusammenhang mit Industriesteuerungen verwendet werden Installation Wartung und Betrieb d rfen nur von durch Artesyn ausgebildeten oder im Bereich Elektronik oder Elektrotechnik qualifiziertem Personal durchgef hrt werden Die in diesem Handbuch enthaltenen Informationen dienen ausschlie lich dazu das Wissen von Fachpersonal zu erg nzen k nnen es aber in keinem Fall ersetzen EMV Das Blade wurde in einem Artesyn Standardsystem getestet Es erf llt die f r digitale Ger te der Klasse A g ltigen Grenzwerte in einem solchen System gem den FCCRichtlinien Abschnitt 15 bzw EN 55022 Klasse A Di
119. ly with the delivery note 2 Visually inspect the shelf to ensure that all of the connector pins are straight shrouds are properly seated screws are tight etc Centellis 4100 Getting Started 6806800E1 8B 117 Site Preparation 2 2 2 118 Check the rails for proper alignment Check that the air filter is properly installed Check that the cable connections are secure and properly fitted Check the EMI gaskets for damage N DD Ww A W Check the items listed above for damage and report any damage or differences to the customer service at www artesyn com computing 00 Tighten loose screws before proceeding 9 Remove the desiccant bags delivered together with the system and dispose of them according to your country s legislation The system is thoroughly inspected before shipment If any damage occurred during transportation or any items are missing please contact our customer s service immediately Site and Installation Planning Planning basic site and installation requirements you have to consider the following issues 1 Is adequate power for the Centellis 4100 system available Can the system be positioned in a way that 48 to 60V DC power source is easy to reach Are racks with sufficient space to install the system available Is suitable equipment available to lift the system into the rack Se a Is there enough space to run a system console terminal Is the cable long enough to reach the
120. mage your system Make sure that TPE connectors near your working area are clearly marked as network connectors e Verify that the length of an electric cable connected to a TPE bushing does not exceed 100 meters Make sure the TPE bushing of the system is connected only to safety extra low voltage circuits SELV circuits e Ifin doubt ask your system administrator Centellis 4100 Getting Started 6806800E1 8B Centellis 4100 Shelf Safety Notes Laser Personal Injury Some variants of the blades in the system are Class 1 laser products The use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure Some variants of the RTM are a Class 1 laser product The use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure Battery Blade Damage Wrong battery installation may result in hazardous explosion and blade damage Always use the same type of battery as is installed and make sure the battery is installed as described in the user manual of the blade Always dispose of old batteries according to your country s legislation Environment Environmental Always dispose of used blades system components and RTMs according to your country s legislation and manufacturer s instructions Centellis 4100 Getting Started 6806800E18B 29 Centellis 4100 Shelf Safety Notes eee EE
121. n so kann dies mit grosser Wahrscheinlichkeit zu starken St rungen f hren welche dann auf Kosten des Produktanwenders beseitigt werden m ssen nderungen oder Modifikationen am Produkt welche ohne ausdr ckliche Genehmigung von Artesyn ECC durchgef hrt werden k nnen dazu f hren dass der Anwender die Genehmigung zum Betrieb des Produktes verliert Boardprodukte werden in einem repr sentativen System getestet um zu zeigen dass das Board den oben aufgef hrten EMV Richtlinien entspricht Eine ordnungsgem sse Installation in einem System welches die EMV Richtlinien erf llt stellt sicher dass das Produkt gem ss den EMV Richtlinien betrieben wird Verwenden Sie nur abgeschirmte Kabel zum Anschluss von Zusatzmodulen So ist sichergestellt dass sich die Aussendung von Hochfrequenzstrahlung im Rahmen der erlaubten Grenzwerte bewegt Warnung Dies ist eine Einrichtung der Klasse A Diese Einrichtung kann im Wohnbereich Funkst rungen verursachen In diesem Fall kann vom Betreiber verlangt werden angemessene Ma nahmen durchzuf hren Centellis 4100 Getting Started 6806800E18B ATCA F120 Sicherheitshinweise Operation Besch digung des Blades Hohe Luftfeuchtigkeit und Kondensat auf der Oberfl che des Blades k nnen zu Kurzschl ssen f hren Betreiben Sie das Blade nur innerhalb der angegebenen Grenzwerte f r die relative Luftfeuchtigkeit und Temperatur Stellen Sie vor dem Einschalten des Stroms sicher dass sich auf dem Blade
122. n input line A and input line B so that line A remains powered even if it is disconnected from the power supply circuit and vice versa To avoid damage or injuries always check that there is no more voltage on the line that has been disconnected before continuing your work Configuration Switches Jumpers Blade Malfunction Switches marked as reserved might carry production related functions and can cause the blade to malfunction if their setting is changed Therefore do not change settings of switches marked as reserved The setting of switches which are not marked as reserved has to be checked and changed before blade installation Blade Damage Setting resetting the switches during operation can cause blade damage Therefore check and change switch settings before you install the blade Centellis 4100 Getting Started 6806800E1 8B 63 ATCA F120 Safety Notes Installation 64 Blade Damage and Additional Devices and Modules Incorrect installation or removal of additional devices or modules may damage the blade or the additional devices or modules Before installing or removing additional devices or modules read the respective documentation Damage of Circuits Electrostatic discharge and incorrect installation and removal of the blade can damage circuits or shorten their life Before touching the blade or electronic components make sure that your are working in an ESD safe environment Blade Damage Incorrect
123. n internal environmental requirements 5 to 95 non condensing according to Artesyn internal environmental requirements Vibration 0 1g from 5 to 100 Hz and back to 5 Hz at a rate of 0 1 octave minute 5 20 Hz at 0 01 g Hz 20 200 Hz at 3 0 dB octave Random 5 20 Hz at 1 m Sec Random 20 200 Hz at 3 m Sec Shock Half sine 11 m Sec 30 mSec sec Blade level packaging Half sine 6 mSec at 180 m Sec Free Fall 1 200 mm all edges and corners 1 0m packaged per ETSI 300 019 2 2 blade level packaging 100mm unpackaged per GR 63 CORE Centellis 4100 Getting Started 6806800E18B 149 Installing the ATCA F120 150 During the safety qualification of this blade the following on board locations were identified as critical with regards to the maximum temperature during blade operation To guarantee proper blade operation and to ensure safety you have to make sure that the temperatures at the locations specified in the following are not exceeded If not stated otherwise the temperatures should be measured by placing a sensor exactly at the given locations For your convenience all temperature spots are shown in a figure that provides a detailed view of the blade Centellis 4100 Getting Started 6806800E18B Installing the ATCA F120 Critical Temperature Spots Figure 5 1 IST
124. n manual may cause harmful interference to radio communications Centellis 4100 Getting Started 6806800E18B 101 RTM ATCA 7221 SCS Safety Notes 102 Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Changes or modifications not expressly approved by Artesyn could void the user s authority to operate the equipment A proper installation in a compliant system will maintain the required performance Use only shielded cables when connecting peripherals to assure that appropriate radio frequency emissions compliance is maintained Centellis 4100 Getting Started 6806800E1 8B RTM ATCA 7221 SCS Safety Notes Installation Damage of Circuits Electrostatic discharge and incorrect installation and removal of the product can damage circuits or shorten their life Before touching the product or electronic components make sure that your are working in an ESD safe environment Product Damage Incorrect installation of the product can cause damage of the product Only use handles when installing removing the product to avoid damage deformation to the face plate and or PCB Data Loss Removing the RTM with the system power on and the blue LED on the front blade still flashing causes data loss Before removing the RTM from a powered system power down the slot by opening the lower handle of the front blade and wait
125. n und darf ausschlie lich f r Anwendungen in der Telekommunikationsindustrie und im Zusammenhang mit Industriesteuerungen verwendet werden Einbau Wartung und Betrieb d rfen nur von durch Artesyn ausgebildetem oder im Bereich Elektronik oder Elektrotechnik qualifiziertem Personal durchgef hrt werden Die in diesem Handbuch enthaltenen Informationen dienen ausschlie lich dazu das Wissen von Fachpersonal zu erg nzen k nnen dieses jedoch nicht ersetzen Halten Sie sich von stromf hrenden Leitungen innerhalb des Produktes fern Entfernen Sie auf keinen Fall Abdeckungen am Produkt Nur werksseitig zugelassenes Wartungspersonal oder anderweitig qualifiziertes Wartungspersonal darf Abdeckungen entfernen um Komponenten zu ersetzen oder andere Anpassungen vorzunehmen Installieren Sie keine Ersatzteile oder f hren Sie keine unerlaubten Ver nderungen am Produkt durch sonst verf llt die Garantie Wenden Sie sich f r Wartung oder Reparatur bitte an die f r Sie zust ndige Gesch ftsstelle von Artesyn So stellen Sie sicher dass alle sicherheitsrelevanten Aspekte beachtet werden Das Produkt wurde in einem Artesyn Standardsystem getestet Es erf llt die f r digitale Ger te der Klasse A g ltigen Grenzwerte in einem solchen System gem den FCC Richtlinien Abschnitt 15 bzw EN 55022 Klasse A Diese Grenzwerte sollen einen angemessenen Schutz vor St rstrahlung beim Betrieb des Produktes in Gewerbe sowie Industriegebieten gew hrleisten
126. ncy emissions compliance is maintained Installation Before installing the board make sure the requirements listed in section Board Exchange are met Restricted access area This board is only to be installed in a restricted access area 46 Centellis 4100 Getting Started 6806800E18B ATCA M100 Safety Notes Data Loss Removing the board with the blue LED still blinking causes data loss Wait until the blue LED is permanently illuminated before removing the board Damage of Circuits Electrostatic discharge and incorrect board installation and removal can damage circuits or shorten their life Before touching the board or electronic components make sure that you are working in an ESD safe environment or wear ESD wrist straps Board Malfunctioning Incorrect board installation and removal can result in board malfunctioning Make sure that the board is connected to the system backplane via all assembled connectors and that power is available on all zone 1 power pins Damage of the Product Incorrect installation of the product can cause damage of the product Only use handles when installing removing the product to avoid damage deformation to the face plate and or PCB Damage of the Product and Additional Devices and Modules Incorrect installation or removal of additional devices or modules may damage the product or the additional devices or modules Before installing or removing additional devices or modules read the respe
127. nd ndern Sie die Schaltereinstellungen bevor Sie das Blade installieren Installation 70 Besch digung des Blades und von Zusatzmodulen Fehlerhafte Installation von Zusatzmodulen kann zur Besch digung des Blades und der Zusatzmodule f hren Lesen Sie daher vor der Installation von Zusatzmodulen die zugeh rige Dokumentation Besch digung von Schaltkreisen Elektrostatische Entladung und unsachgem er Ein und Ausbau von Blades kann Schaltkreise besch digen oder ihre Lebensdauer verk rzen Bevor Sie Blades oder elektronische Komponenten ber hren vergewissern Sie sich da Sie in einem ESD gesch tzten Bereich arbeiten Besch digung des Blades Fehlerhafte Installation des Blades kann zu einer Besch digung des Blades f hren Verwenden Sie die Handles um das Blade zu installieren deinstallieren Auf diese Weise vermeiden Sie dass das Front Panel oder die Platine deformiert oder zerst rt wird Besch digung des Blades der Backplane oder von System Komponenten Verbogene Pins oder lose Komponenten k nnen zu einer Besch digung des Blades der Backplane oder von Systemkomponenten f hren berpr fen Sie daher das Blade sowie die Backplane vor der Installation sorg ltig und stellen Sie sicher dass sich beide in einwandfreien Zustand befinden und keine Pins verbogen sind Artesyn und unsere Zulieferer unternehmen gr te Anstrengungen um sicherzustellen dass sich Pins und Stecker von Boards vor dem Verlassung der Pro
128. nder FILTER OPTIONS click the Document types drop down list box to select the type of document you are looking for In the Search text box type the product name and click GO Table A 1 Artesyn Embedded Technologies Embedded Computing Publications Document Title Publication Number Centellis 4100 Document Collection 6806800E09 Power Entry Modules and Blowers of Centellis 4100 Control via IPMI 6806800E11 Programmer s Reference Centellis 4100 Release Notes 6806800E15 System Management Interface Based on HPI B Centellis CO 31kX 4100 6806800D84 ATCA M100 Installation and Use 6806800D83 ATCA M100 Control via IPMI Programmer s Reference 6806800C86 ATCA F120 Installation and Use 6806800D06 ATCA F120 Control via IPMI Programmer s Reference 6806800D18 RTM ATCA F120 Installation and Use 6806800D07 RTM ATCA F120 Control via IPMI Programmer s Reference 6806800D17 SPARE ATCA A100 Reference Guide 6806800C68 SPARE ATCA A100 Control via IPMI Programmer s Reference 6806800C85 ATCA 7221 Reference Guide 6806800095 PENT ATCA 7221 and ATCA 7221 Control via IPMI Programmer s 6806800C89 Reference Centellis 4100 Getting Started 6806800E18B 213 Related Documentation Table A 1 Artesyn Embedded Technologies Embedded Computing Publications continued Document Title Publication Number RTM ATCA 7221 SCS Installation Guide 6806800A41 ACC RTM 7221 SCSI and RTM ATCA 7221
129. nformationen dienen ausschlie lich dazu das Wissen von Fachpersonal zu erg nzen k nnen dieses jedoch nicht ersetzen Halten Sie sich von stromf hrenden Leitungen innerhalb des Blades fern Entfernen Sie auf keinen Fall Abdeckungen am Blade Nur werksseitig zugelassenes Wartungspersonal oder anderweitig qualifiziertes Wartungspersonal darf Abdeckungen entfernen um Komponenten zu ersetzen oder andere Anpassungen vorzunehmen Installieren Sie keine Ersatzteile oder f hren Sie keine unerlaubten Ver nderungen am Blade durch sonst verf llt die Garantie Wenden Sie sich f r Wartung oder Reparatur bitte an die f r Sie zust ndige Gesch ftsstelle von Artesyn So stellen Sie sicher dass alle sicherheitsrelevanten Aspekte beachtet werden Centellis 4100 Getting Started 6806800E18B 67 ATCA F120 Sicherheitshinweise EMV 68 Das Produkt wurde in einem Artesyn Standardsystem getestet Es erf llt die f r digitale Ger te der Klasse A g ltigen Grenzwerte in einem solchen System gem den FCCRichtlinien Abschnitt 15 bzw EN 55022 Klasse A Diese Grenzwerte sollen einen angemessenen Schutz vor St rstrahlung beim Betrieb des Produktes in Gewerbe sowie Industriegebieten gew hrleisten Das Produkt arbeitet im Hochfrequenzbereich und erzeugt St rstrahlung Bei unsachgem em Einbau und anderem als in diesem Handbuch beschriebenen Betrieb k nnen St rungen im Hochfrequenzbereich auftreten Wird das Produkt in einem Wohngebiet betriebe
130. nschlie en einer Telefonleitung an einen solchen TPE Stecker sowohl das Telefon als auch das Board zerst ren kann Beachten Sie deshalb die folgenden Hinweise e Kennzeichnen Sie TPE Anschl sse in der N he Ihres Arbeitsplatzes deutlich als Netzwerkanschl sse e Schlie en Sie an TPE Buchsen ausschlie lich SELV Kreise Sicherheitskleinspannungsstromkreise an DieL nge des mit dem Board verbundenen Twisted Pair Ethernet Kabels darf 100 m nicht berschreiten 54 Centellis 4100 Getting Started 6806800E18B ATCA M100 Sicherheitshinweise Falls Sie Fragen haben wenden Sie sich bitte an Ihren Systemadministrator Austausch Erweiterung Verwenden Sie bei Austausch oder Erweiterung nur von Artesyn empfohlene Komponenten und Systemteile Andernfalls sind Sie f r m gliche Auswirkungen auf EMV oder Fehlfunktionen des Produktes voll verantwortlich Uberpriifen Sie die gesamte aufgenomme Leistung aller eingebauten Komponenten siehe die technischen Daten der entsprechenden Komponente Stellen Sie sicher dass die Stromaufnahme jedes Verbrauchers innerhalb der zulassigen Grenzwerte liegt siehe die technischen Daten des entsprechenden Verbrauchers Umweltschutz Entsorgen Sie alte Batterien und oder Produkte stets gem der in Ihrem Land g ltigen Gesetzgebung und den Empfehlungen des Herstellers Centellis 4100 Getting Started 6806800E18B 55 ATCA M100 Sicherheitshinweise eee EEE 56 Centellis 4100 Getting Started 68
131. nt integrity before installation Centellis 4100 Getting Started 6806800E1 8B 75 RTM ATCA F120C Safety Notes Artesyn and our suppliers take significant steps to ensure there are no bent pins on the backplane or connector damage to the blades RTMs prior to leaving the factory Bent pins caused by improper installation or by inserting blades with damaged connectors could void the ECC warranty for the backplane or blades Cabling and Connectors Blade Damage The R 45 connector s on the face plate are twisted pair Ethernet TPE or E1 T1 J1 interfaces Connecting an E1 T1 J1 line to an Ethernet connector may damage the product Make sure that TPE connectors near your working area are clearly marked as network connectors Verify that the length of an electric cable connected to a TPE bushing does not exceed 100 meters Make sure the TPE bushing of the system is connected only to safety extra low voltage circuits SELV circuits If in doubt ask your system administrator Environment Always dispose of used blades system components and RTMs according to your country s legislation and manufacturer s instructions 76 Centellis 4100 Getting Started 6806800E18B RTM ATCA F120C Sicherheitshinweise ss Dieses Kapitel enth lt Hinweise die potentiell gef hrlichen Prozeduren innerhalb dieses Handbuchs vorrangestellt sind Beachten Sie unbedingt in allen Phasen des Betriebs der Wartung und der Reparatur des Systems die A
132. ntellis 4100 Getting Started 6806800E18B Site Preparation Blower trays are mounted in the shelf top The figure below shows the general airflow for the system Figure 2 5 Shelf Airflow Blowers Air Outlet Front Rear Air Inlet The cooling system is designed to manage a heat dissipation of 220W per front slot and additional 20W per rear slot The actual cooling performance also depends on the slot population and the heatsink design of the installed blades and should be validated based on the used system configuration Centellis 4100 Getting Started 6806800E18B 129 Site Preparation 2 2 7 130 Failure of maximal one blower is allowed The distance to other equipment must be sufficient to avoid an overheating of the system If you install the system into a closed frame ensure that the air inlet and outlet are kept free Acoustic Noise Control The system can generate a lot of acoustic noise This system has a built in noise control due to the blower speed control If the system is installed in an environment where the noise may be harmful to personnel being exposed to the noise during extended time periods additional protective measures should be considered Centellis 4100 Getting Started 6806800E18B Site Preparation 2 3 Centellis 4100 Getting Started 6806800E18B Site Planning Checklists Figure 2 6 Planning Checklist 1 Planning Determine where to install the system and ensure that the requi
133. nweisungen die diesen Hinweisen enthalten sind Sie sollten au erdem alle anderen Vorsichtsma nahmen treffen die f r den Betrieb des Produktes innerhalb Ihrer Betriebsumgebung notwendig sind Wenn Sie diese Vorsichtsma nahmen oder Sicherheitshinweise die an anderer Stelle diese Handbuchs enthalten sind nicht beachten kann das Verletzungen oder Sch den am Produkt zur Folge haben Artesyn ist darauf bedacht alle notwendigen Informationen zum Einbau und zum Umgang mit dem Produkt in diesem Handbuch bereit zu stellen Da es sich jedoch um ein komplexes Produkt mit vielf ltigen Einsatzm glichkeiten handelt k nnen wir die Vollst ndigkeit der im Handbuch enthaltenen Informationen nicht garantieren Falls Sie weitere Informationen ben tigen sollten wenden Sie sich bitte an die f r Sie zust ndige Gesch ftsstelle von Artesyn Das System erf llt die f r die Industrie geforderten Sicherheitsvorschriften und darf ausschlie lich f r Anwendungen in der Telekommunikationsindustrie und im Zusammenhang mit Industriesteuerungen verwendet werden Einbau Wartung und Betrieb d rfen nur von durch Artesyn ausgebildetem oder im Bereich Elektronik oder Elektrotechnik qualifiziertem Personal durchgef hrt werden Die in diesem Handbuch enthaltenen Informationen dienen ausschlie lich dazu das Wissen von Fachpersonal zu erg nzen k nnen dieses jedoch nicht ersetzen Halten Sie sich von stromf hrenden Leitungen innerhalb des Produktes fern Entfern
134. of the operator This is a Class A product based on the standard of the Voluntary Control Council for Interference by Information Technology Interference VCCI If this equipment is used ina domestic environment radio disturbance may arise When such trouble occurs the user may be required to take corrective actions Centellis 4100 Getting Started 6806800E1 8B Centellis 4100 Shelf Safety Notes System Installation System Damage To avoid system damage verify that the system environment meets the environmental and power requirements given in this manual before installing the system Before you begin to set up and cable your new system consider these guidelines Restricted access area Install the system only ina restricted access area Installation codes This unit must be installed in accordance with the National Electrical Code Articles 110 16 110 17 and 110 18 and the Canadian Electrical Code Section 12 a Overcurrent protection A readily accessible listed branch circuit overcurrent protective device must be incorporated into the building wiring For appropriate AWG rating of the overcurrent protection device see NEC Table 310 16 and other national regulations The protective bonding conductor depends on your power distribution topology Make sure that you use an appropriate protective bonding conductor regarding the rating of the branch circuit protection Install the system safely Make sure that cables and cords are out
135. omf hrenden Leitungen innerhalb des Produktes fern Entfernen Sie auf keinen Fall Abdeckungen am Produkt Nur werksseitig zugelassenes Wartungspersonal oder anderweitig qualifiziertes Wartungspersonal darf Abdeckungen entfernen um Komponenten zu ersetzen oder andere Anpassungen vorzunehmen Installieren Sie keine Ersatzteile oder f hren Sie keine unerlaubten Ver nderungen am Produkt durch sonst verf llt die Garantie Wenden Sie sich f r Wartung oder Reparatur bitte an die f r Sie zust ndige Gesch ftsstelle von Artesyn So stellen Sie sicher dass alle sicherheitsrelevanten Aspekte beachtet werden Centellis 4100 Getting Started 6806800E18B 97 RTM ATCA 7221 FC Sicherheitshinweise EMV 98 Das Produkt wurde in einem Artesyn Standardsystem getestet Es erf llt die f r digitale Ger te der Klasse A g ltigen Grenzwerte in einem solchen System gem den FCCRichtlinien Abschnitt 15 bzw EN 55022 Klasse A Diese Grenzwerte sollen einen angemessenen Schutz vor St rstrahlung beim Betrieb des Produktes in Gewerbe sowie Industriegebieten gew hrleisten Das Produkt arbeitet im Hochfrequenzbereich und erzeugt St rstrahlung Bei unsachgem em Einbau und anderem als in diesem Handbuch beschriebenen Betrieb k nnen St rungen im Hochfrequenzbereich auftreten Warnung Dies ist eine Einrichtung der Klasse A Diese Einrichtung kann im Wohnbereich Funkst rungen verursachen In diesem Fall kann vom Betreiber verlangt werden angemessene
136. ot be used as replacement for qualified personnel Keep away from live circuits inside the equipment Operating personnel must not remove equipment covers Only factory authorized service personnel or other qualified service personnel may remove equipment covers for internal subassembly or component replacement or any internal adjustment Do not install substitute parts or perform any unauthorized modification of the equipment or the warranty may be voided Contact your local Artesyn representative for service and repair to make sure that all safety features are maintained The blade has been tested in a standard Artesyn system and found to comply with the limits for a Class A digital device in this system pursuant to part 15 of the FCC Rules EN 55022 Class A respectively These limits are designed to provide reasonable protection against harmful interference when the system is operated in a commercial environment Centellis 4100 Getting Started 6806800E1 8B 81 ATCA 7221 Safety Notes 82 This is a Class A product based on the standard of the Voluntary Control Council for Interference by Information Technology Interference VCCI If this equipment is used ina domestic environment radio disturbance may arise When such trouble occurs the user may be required to take corrective actions The blade generates and uses radio frequency energy and if not installed properly and used in accordance with this guide may cause harmful interference
137. owers Personal Injury Rotating Blowers Inserting tools or fingers into operational blowers may cause injuries Blowers become exposed when the blower tray is pulled Keep clear of the blowers as long as they are rotating When the blower is removed extreme care should be taken while handling the blower itself The centrifugal forces will make the unit difficult to handle Personal Injury The cabling should follow existing cable paths using existing or similar cable fastenings Never change the system s cabling as delivered by Artesyn Check proper function of the system after cabling extensions To avoid injuries always ensure that cables are securely installed so that nobody can trip over them Personal Injury through Electric Shock Touching contacts and cables during system operation can cause injuries through electric shock To avoid electric shock make sure that contacts and cables of the system cannot be touched while the system is operating If in doubt concerning cabling ask your local Artesyn representative Cable Damage Folding the fiber cable damages the cable and inhibits the data transmission Therefore make sure you do not fold the cable Centellis 4100 Getting Started 6806800E1 8B 27 Centellis 4100 Shelf Safety Notes RJ 45 Connector 28 System Damage RJ 45 connectors on blades are either twisted pair Ethernet TPE or E1 T1 J1 network interfaces Connecting an E1 T1 J1 line to an Ethernet connector may da
138. perating the system in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Installation Electrostatic discharge and incorrect board installation and removal can damage circuits or shorten their life Therefore e Touching the board or electronic components in a non ESD protected environment causes component and board damage Before touching boards or electronic components make sure that you are working in an ESD safe environment Ifthe board is delivered as part of a system do not change the cabling of the board unless it is explicitly stated in the system s documentation Centellis 4100 Getting Started 6806800E1 8B 57 SPARE ATCA A100 Safety Notes Operation While operating the board ensure that the environmental and power requirements are met High humdity and condensation on the surface cause short circuits Only operate the board above 0 C Make sure the board is completely dry and there is no moisture on any surface before applying power When operating the board in areas of electromagnetic radiation ensure that the board is bolted on the AdvancedTCA shelf and the shelf is shielded by enclosure Make sure that contacts and cables of the board cannot be touched while the board is operating Environment Always dispose of used batteries and or old boards according to your country s legislation if possible in an environmental
139. peration 90 C 194 F maximum temperature with decreased warranty lifetime 2 TX1322 TLV 1 transformer 80 C 176 F 3 TX1322 TLV 1 transformer 80 C 176 F 4 Controller 90 C 194 F Centellis 4100 Getting Started 6806800E18B 177 Installing the RTM ATCA 7221 SCS Figure 7 1 Critical Temperature Spots 7 1 2 2 Power Requirements The RTM draws approximately 25W from the front blade which it is attached to 7 1 2 3 Backplane Requirements For installing the RTM you need a system without a zone 3 midplane 178 Centellis 4100 Getting Started 6806800E18B Installing the RTM ATCA 7221 SCS 7 2 Module Installation NOTICE RTM Damage Installing the RTM with other blades than the Centellis 4100 may damage the RTM and the front blade Only install the RTM with the Artesyn Centellis 4100 blade Damage of Circuits Electrostatic discharge and incorrect RTM installation and removal can damage circuits or shorten their life Before touching the RTM or electronic components make sure that you are working in an ESD safe environment Centellis 4100 Getting Started 6806800E18B 179 Installing the RTM ATCA 7221 SCS 7 2 1 Installing the RTM Installation Procedure Follow the following steps to install the RTM 1 Locate the slot the RTM is to be installed into the shelf s rear which must be the same as that of the front blade 2 Ensure that the top and the bottom
140. put line B so that line A remains powered even if it is disconnected from the power supply circuit and vice versa To avoid damage or injuries always check that there is no more voltage on the line that has been disconnected before continuing your work Expansion System Overload To avoid an overload of the system check the total power consumption of all components installed see the technical specification of the respective components Ensure that any individual output current of any source stays within its acceptable limits see the technical specification of the respective source Loss of Safety Compliance Using of Additional Plug in Blades By using additional plug in blades it may be possible that the system may be no more compliant to safety and EMC regulations The system integrator has to ensure that the compliancy is guaranteed Centellis 4100 Getting Started 6806800E1 8B 25 Centellis 4100 Shelf Safety Notes Exchanging PEMs Personal Injury through Electric Shock and Burning Touching the PEM power input terminals with metallic objects on your hands wrists or hanging from your neck may lead to serious injuries like burns or amputations Do not wear any metallic attire or commodity on your hands wrists or hanging from your neck when working at the power input terminals or power input cables Be extremely careful when you use electrically conductive tools near the PEMs Short Circuits or Personal Injury Ensure that
141. rature l e The Centellis 4100 system regulates the blower speed based on the temperature sensors present in the system The blower speed is adjusted to the lowest speed which still keeps the evaluated temperature readings below or at their respective upper non critical threshold Hence the blower speed depends on the ambient temperature blade design temperature threshold settings and system configuration 120 Centellis 4100 Getting Started 6806800E18B Site Preparation To guarantee proper blade operation you have to make sure that the temperatures at the locations specified in the following are not exceeded If not stated otherwise the temperatures should be measured by placing a sensor exactly at the given locations For your convenience all temperature spots are shown in the figures below Table 2 2 Critical Temperature Limits Component Temperature Limit Air inlet system s front 55 C 131 F Air outlet system s rear 70 C 158 F Power entry module lug plastic washer 70 C 158 F gt 70 C 158 F and maximum 90 C 194 F the cables must be isolated and must be approved to be used in this temperature range gt 70 C 158 F and maximum 90 194 F the service personal may touch the components The cables must be isolated and the hot surface icon must be attached The cables must be approved to be used in this temperature range Centellis 4100 Getting
142. red installation tools and equipment are Control the available installation tools and equipment Ensure that enough space is Determine the needed power Plan the cable management Ensure proper cooling Schedule the arrival of the system Consider consulting of Artesyn services The following table lists the tasks which you have to perform as plan the installation of the system 131 Site Preparation Figure 2 7 Planning Checklist 2 Issue Entry General site review Order number Schedules shipping date Installation date Site address Company name Special Instructions Operational days Contact data Contact name Phone number Fax number E Mail address Site constructions What floor Path to the installation area clear Freight elevator available How many shelves must be installed Enough space available DC or AC available All required cables available To be continued 132 Centellis 4100 Getting Started 6806800E18B Chapter 3 Installing the System 1 3 1 Overview The following sections help you to start up and maintain the system Step Before installation Description This section provides information about the requirements unpacking and inspecting the delivery and the
143. requirements Free Fall 1 200 mm all edges and corners Centellis 4100 Getting Started 6806800E18B 185 Installing the ATCA 7221 To guarantee proper blade operation you have to make sure that the temperatures at the locations specified in the following are not exceeded If not stated otherwise the temperatures should be measured by placing a sensor exactly at the given locations For your convenience all temperature spots are shown in a figure that provides a detailed view of the blade Table 8 2 Critical Temperature Limits Location Component Temperature Limit 1 Pentium Xeon Processor 85 C 185 F 2 Pentium Xeon Processor 85 C 185 F 3 Intel 6700PXH 64 bit PCI Hub 85 C 185 F 4 E7520 Memory Controller 90 C 194 F 5 Memory modules 85 C 185 F Temperature limit applies to all components on board of each memory module 6 3 3V DC DC converter 90 C 194 F 7 Ericsson power converter 100 C 221 F 186 Centellis 4100 Getting Started 6806800E18B Installing the ATCA 7221 Location of Critical Blade Temperature Spots Blade Top Side Figure 8 1 187 Centellis 4100 Getting Started 680680
144. rische Komponenten in einem nicht ESD gesch tzten Bereich kann dies zu einer Besch digung des Boards f hren Bevor Sie Boards oder elektronische Komponenten ber hren vergewissern Sie sich dass Sie in einem ESD gesch tzten Bereich arbeiten Centellis 4100 Getting Started 6806800E18B 35 Centellis 4100 Shelf Sicherheitshinweise 36 Reihenfolge bei der Installation von RTMs und AdvancedTCA Boards Die folgende Reihenfolge mu bei der Installation von RTMs und AdvancedTCA Boards eingehalten werden Installieren Sie zuerst das RTM und erst danach das passende AdvancedTCA Board Ansonsten k nnen RTM oder Board besch digt werden Besch digung des Boards oder Systems Wird ein Board in den falschen Steckplatz im System gesteckt k nnen sowohl das Board als auch das System besch digt werden Installieren Sie Boards deshalb ausschlie lich in daf r vorgesehene Steckpl tze Besch digung des RTMs oder Boards Wird das RTM ausgebaut w hrend die Payload des dazugeh rigen AdvancedTCA Boards noch nicht heruntergefahren ist kann dies zu Besch digungen am Board oder RTM f hren Fahren Sie deshalb die Payload des AdvancedTCA Blades immer herunter bevor Sie das dazugeh rige RTM aus dem System entfernen Besch digung des RTMs Fehlerhafte Installation kann zu einer Besch digung des RTMs f hren Verwenden Sie die Handles um das RTM zu installieren deinstallieren Auf diese Weise vermeiden Sie dass die Frontblende oder die Platin
145. rstellen Austausch von PEMs 40 Verletzungsgefahr durch Stromschlag und Verbrennungen Ber hren metallische Gegenst nde an H nden Handgelenken oder am Hals die Input Terminals der PEMs kann dies zu extremen Verletzungen wie zum Beispiel Verbrennungen oder Amputationen f hren Tragen Sie bei der Arbeit mit dem System keine metallischen Gegenst nde an Ihren H nden oder Armen und lassen sie keine metallischen Gegenst nde um Ihren Hals h ngen Seien Sie extrem vorsichtig mit elektrisch leitenden Gegenst nden in der N he der PEMs Kurzschlu und Gefahr durch Stromschlag Um einen elektrischen Schlag zu vermeiden berzeugen Sie sich dass vor dem Austausch des PEMs die Stromzufuhr unterbrochen ist und w hrend des Austausches unterbrochen bleibt Kurzschlu und Gefahr durch Stromschlag Um Kurzschl sse und elektrischen Schlag zu vermeiden berzeugen Sie sich dass vor dem L sen der Schrauben die Stromzufuhr unterbrochen ist und w hrend des Austausches unterbrochen bleibt Vermeiden Sie Kurzschl sse indem Sie sehr vorsichtig mit dem Werkzeug umgehen Verletzungsgefahr Spannungsversorgungseinheiten werden sehr hei Das Ber hren einer hei en Spannungsversorgungseinhei kann zu Verletzungen f hren Lassen Sie sie abk hlen bevor Sie sie mit blo en H nden herausziehen Besch digung der Spannungsversorgungseinheit Wir die Spannungsversorgungseinheit verkehrt angeschlossen werden die Elektrolytkondensatoren der Filter
146. rted 6806800E18B 205 Starting up the System eee EEE 206 Centellis 4100 Getting Started 6806800E18B System Software ee 10 1 Overview Chapter 10 This chapter lists available software components for the Centellis 4100 system and where to find more information about it Furthermore this chapter lists available upgrade options for system software components 10 2 Available Software The following table lists which software is available for system components and where to find more information about it Each software component is preinstalled on the respective system component Table 10 1 Software Available on System Components Component AMC module Software Basic Blade Services Software including Operating System Hardware management functions Set of management routines for Linux and all hardware interfaces Where to Find More Information Basic Blade Services Programmer s Reference for the respective module only if it is an Artesyn module for which BBS is available ATCA A100 IPMI firmware SPARE ATCA A 100 Control via IPMI Programmer s Reference ATCA F120 Basic Blade Services Software including Operating System Hardware management functions Set of management routines for Linux and all hardware interfaces IPMC firmware images of other blades in the system Network boot images of all other blades in the system Basic Blade Services Software for ATCA F120
147. s 4100 Getting Started 6806800E18B 141 Installing the RTM ATCA F120C Any optional items ordered 2 Check for damage and report any damage or differences to the customer service ly TheRTMis thoroughly inspected before shipment If any damage occurred during S 4 transportation or any items are missing please contact our customer s service immediately e Remove the desiccant bag shipped together with the blade and dispose of it according to your country s legislation 4 3 Environmental and Power Requirements The following environmental and power requirements are applicable to the board 4 3 1 Environmental Requirements You must make sure that the blade when operated in your particular system configuration meets the environmental requirements specified below 11 Operating temperatures refer to the temperature of the air circulating around the RTM and hotto component temperatures If you integrate the RTM in your own non Artesyn system please contact your local sales representative for further safety information NOTICE RTM Damage High humidity and condensation on the RTM surface causes short circuits Do not operate the RTM outside the specified environmental limits Make sure the RTM is completely dry and there is no moisture on any surface before applying power Do not operate the RTM below 5 C 142 Centellis 4100 Getting Started 6806800E18B Installing the RTM ATCA F120C Table 4
148. s Wartungspersonal oder anderweitig qualifiziertes Wartungspersonal darf Abdeckungen entfernen um Komponenten zu ersetzen oder andere Anpassungen vorzunehmen Installieren Sie keine Ersatzteile oder f hren Sie keine unerlaubten Ver nderungen am Produkt durch sonst verf llt die Garantie Wenden Sie sich f r Wartung oder Reparatur bitte an die f r Sie zust ndige Gesch ftsstelle von Artesyn So stellen Sie sicher dass alle sicherheitsrelevanten Aspekte beachtet werden Das Blade wurde in einem Artesyn Standardsystem getestet Es erf llt die f r digitale Ger te der Klasse A g ltigen Grenzwerte in einem solchen System gem den FCGRichtlinien Abschnitt 15 bzw EN 55022 Klasse A Diese Grenzwerte sollen einen angemessenen Schutz vor St rstrahlung beim Betrieb des Blades in Gewerbe sowie Industriegebieten gew hrleisten Centellis 4100 Getting Started 6806800E18B 87 ATCA 7221 Sicherheitshinweise 88 Das Blade arbeitet im Hochfrequenzbereich und erzeugt St rstrahlung Bei unsachgem em Einbau und anderem als in diesem Handbuch beschriebenen Betrieb k nnen St rungen im Hochfrequenzbereich auftreten Warnung Dies ist eine Einrichtung der Klasse A Diese Einrichtung kann im Wohnbereich Funkst rungen verursachen In diesem Fall kann vom Betreiber verlangt werden angemessene Ma nahmen durchzuf hren Centellis 4100 Getting Started 6806800E18B ATCA 7221 Sicherheitshinweise Installation Betrieb Besch digung von S
149. s at the system s rear side which can be populated with 14 RTMs These RTM connections provide user defined input and output connectivity to the corresponding front blades e Four IPMC enabled intelligent blowers e Four single entry DC Feed intelligent Power Entry Modules PEMs with 50A breaker and line filter e Airfilter e Rear ESD wrist strap sockets and grounding studs 110 Centellis 4100 Getting Started 6806800E18B Introduction Figure 1 1 System Front View Centellis 4100 Getting Started 6806800E18B 111 Introduction 1 2 1 112 Figure 1 2 System Rear View B ple ul The system is designed to meet Network Equipment Building Systems NEBS level 3 tests Shelf The 13U 575 mm or 22 64 inch high and 440 mm 17 32 inch deep shelf for 19 racks is made of stainless steel There is one mounting bracket at each side of the shelf designed for front mounting the shelf into arack Depending on the rack the shelf is installed in there are two possible locations of the mounting brackets at the shelf s side You can install the system in a standard 19 rack or you can operate it on a desk Centellis 4100 Getting Started 6806800E18B Introduction 1 2 2 Backplane The backplane is fully compliant with the PICMG 3 0 R2 0 Specification and it has been designed with the following features e Two hub slots 12 node slots 14 slot fabric interface with dual star interconnect Base int
150. schen Artesyn empfiehlt die L fter alle 90 Tage auszutauschen Wie h ufig Sie die Filter austauschen m ssen h ngt von der Umgebung ab in der das System betrieben wird Luftfilter sollten mindestens alle 90 Tage ausgewechselt werden Je nach Umgebungsbedingen kann dies auch fr her n tig sein Da die Verh ltnisse in Vermittlungsstellen sehr unterschiedlich sein k nnen sollten Sie die Luftfilter nach der Erstinstallation des Systems jede Woche kontrollieren In einer staubigen Umgebung muss ein Centellis 4100 Getting Started 6806800E18B Centellis 4100 Shelf Sicherheitshinweise Filter gegebenenfalls fter gereinigt werden als in einer sauberen Umgebung Pr fen Sie den Filter regelm ig bis Sie eine Vorstellung davon haben wie oft der Filter gereinigt werden muss Erstellen Sie aufgrund Ihrer Beobachtungen einen Reinigungsplan und protokollieren Sie jede Reinigung oder jeden Austausch des Filters berhitzung des Systems Wenn Sie die Geschwindigkeit der L fter reduzieren steigt die Systemtemperatur an Kontrollieren Sie deshalb st ndig die Temperatur im System wenn Sie die Geschwindigkeit der L fter reduziert haben Stellen Sie w hrend des Betriebs sicher dass die Bedingungen die im Handbuch beschrieben sind eingehalten werden Verlust der Sicherheitszulassung f r das Board ATCA 715 7105 717 7107 und das System Benutzen Sie das Kabel ACC CABLE RJ45 DSUB nur zum Zweck der Instandhaltung Wenn Sie das Kabel mit Produkten
151. se A Diese Grenzwerte sollen einen angemessenen Schutz vor St rstrahlung beim Betrieb des Produkts in Gesch fts Gewerbe sowie Industriebereichen gew hrleisten Das Produkt arbeitet im Hochfrequenzbereich und erzeugt St rstrahlung Bei unsachgem em Einbau und anderem als in diesem Handbuch beschriebenen Betrieb k nnen St rungen im Hochfrequenzbereich auftreten Freie Steckpl tze m ssen mit Platzhalter Boards belegt werden um sicherzustellen dass die EMV Richtlinien erf llt werden Erdung Um eine korrekte Erdung des Systems zu gew hrleisten befinden sich owohl am System als auch an den einzelnen Modulen Dichtungen Stellen Sie sicher da alle Systemteile die EMI Dichtung ber hren Am System befinden sich auch ESD Kontakte Stellen Sie sicher dass jede Person die mit dem System arbeitet mit ESD Schutz zum Beispiel ESD B ndern arbeitet Dies ist eine Einrichtung der Klasse A Diese Einrichtung kann im Wohnbereich Funkst rungen verursachen in diesem Fall kann vom Betreiber verlangt werden angemessene Ma nahmen durchzuf hren und daf r aufzukommen Centellis 4100 Getting Started 6806800E18B Centellis 4100 Shelf Sicherheitshinweise Systeminstallation Besch digung des Systems Bevor Sie das System installieren berpr fen Sie ob die im Handbuch beschriebenen Anforderungen erf llt werden Beachten Sie folgende allgemeinen Sicherheitshinweise vor der Installation und Verkabelung des Systems Bereich mi
152. signed to meet the standard industrial safety requirements It must not be used except in its specific area of office telecommunication industry and industrial control Only personnel trained by Artesyn or persons qualified in electronics or electrical engineering are authorized to install remove or maintain the product The information given in this manual is meant to complete the knowledge of a specialist and must not be used as replacement for qualified personnel Keep away from live circuits inside the equipment Operating personnel must not remove equipment covers Only factory authorized service personnel or other qualified service personnel may remove equipment covers for internal subassembly or component replacement or any internal adjustment Do not install substitute parts or perform any unauthorized modification of the equipment or the warranty may be voided Contact your local Artesyn representative for service and repair to make sure that all safety features are maintained EMC This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to
153. ss Before removing the RTM from a powered system power down the slot by opening the lower handle of the front blade and wait until the blue LED is permanently ON Blade Malfunctioning Incorrect blade installation and removal can result in blade malfunctioning Make sure that the blade is connected to the system backplane via all assembled connectors and that power is available on all zone 1 power pins Centellis 4100 Getting Started 6806800E1 8B Centellis 4100 Shelf Safety Notes Operation System Overheating Cooling vents Inproper cooling can lead to blade and system damage To ensure proper cooling and undisturbed airflow through the system always operate the system in a horizontal position and keep clear at least 60 mm at the back and 60 mm to each side of the system Do not obstruct the ventilation openings at the top sides and back of the system Keep the fresh air intake at the bottom front side of the chassis completely clear and ensure that fresh air supply is not mixed with hot exhaust from other devices To ensure proper air flow within the system make sure that all slots are populated with either filler blades blades or dummy blades Product Damage High humidity and condensation on blade surfaces causes short circuits Do not operate the system outside the specified environmental limits Make sure the system is completely dry and there is no moisture on any surface before applying power Do not start the system belo
154. system 6 Are the inlet and outlet of the blowers and therefore the airflow not blocked Centellis 4100 Getting Started 6806800E18B Site Preparation 2 2 3 Requirements Before and during system installation and operation you always have to ensure that the requirements listed in the following sections are met 2 2 3 1 Environmental Requirements To ensure proper function of the system make sure that the environment in which the system is to be used fulfills the environmental requirements The environmental values must be tested and proven in the planned system configuration that is the delivered system and other third party products you want to integrate tlz Operating temperatures refer to the temperature of the air circulating at the air intake of un the system and not to component temperatures e Some of the climatic values may exceed the specification of some system components for example hard disks As Artesyn cannot guarantee the functionality of third party products that are handled or operated out of their specifications the environmental conditions may be limited to the specifications of these components The following table lists the environmental requirements Table 2 1 Environmental Conditions Feature Operating Non Operating packed state Temperature 5 C 41 F to 40 C 104 F normal 40 C 40 F to 70 C 158 F operation according to NEBS standard GR 63 CORE 5 C 23 F to 55
155. system in a horizontal position Furthermore keep clear at least 6 cm adjacent to the cooling vents on the chassis front and back side Centellis 4100 Getting Started 6806800E18B 135 Installing the System 3 3 1 Installing the System in a Rack The following procedure describes how to install the system in a rack R N i gt Use power input cables with a cross section minimum of 6 mm AWG 8 Personal or System Damage The system is heavy and if you carry it on your own you can hurt your back To prevent injury keep your back straight and have two people to lift the system or use additional lifting equipment Personal or System Damage Unstable system installation in a rack can cause the rack to topple over Therefore if your system is the only one in the rack make sure to mount the system in the lowest part of the rack If other systems are installed in one rack start with the heaviest component at the bottom If the rack is equipped with stabilizing devices make sure that they are installed and extended so that the rack is secure Then proceed to mount or service the system 136 Centellis 4100 Getting Started 6806800E18B Installing the System NOTICE System Damage During the course of handling shipping and assembly pins shrouds and mounting screws blowers and other items can become loose or damaged Do not operate a damaged shelf this can cause damage to devices that interfere with it
156. t eingeschr nkter Zugang Installieren Sie das System nur in Bereichen mit eingeschranktem Zugang Installationsrichtlinien Dieses System muss gem folgender Richtlinien installiert werden National Electrical Code Artikel 110 16 110 17 und 110 18 und Canadian Electrical Code Abschnitt 12 a berstrom Schutzeinrichtung Eine leicht zug ngliche Trennvorrichtung muss in der Geb udeverkabelung eingebaut sein Einen angemessenen AWG American Wire Gauge amerikanische Norm f r Drahtquerschnitte Wert der berstrom Schutzeinrichtung k nnen Sie der NEC National Electrical Code Tabelle 310 16 oder anderen nationalen Regelwerken entnehmen Der Erdungsleiter ist abh ngig von der Spannungsverteilungstopologie innerhalb Ihrer Anlage Stellen Sie sicher dass Sie einen angemessenen Erdungsleiter gem der Auslegung des Zugangsleitungsschutzes verwenden Bauen Sie das System sicher ein Stellen Sie sicher dass Kabel und Leitungen nicht im Weg sind Stellen Sie sicher dass der Systemaufbau anwenderfreundlich ist Centellis 4100 Getting Started 6806800E1 8B 33 Centellis 4100 Shelf Sicherheitshinweise 34 Besch digung des Systems Verschmutzungen k nnen das System besch digen Betreiben Sie das System an einem ersch tterungsfreien Ort an dem weder Staub Rauch noch elektrostatische Entladungen auftreten Stellen Sie au erdem sicher dass die klimatischen Bedingungen die in diesem Handbuch spezifiziert sind eingehalten
157. tal and Power Requirements The following environmental and power requirements are applicable to the blade Environmental Requirements You must make sure that the blade when operated in your particular system configuration meets the environmental requirements specified below Operating temperatures refer to the temperature of the air circulating around the blade and not to component temperatures If you integrate the blade in your own non Artesyn system please contact your local sales representative for further safety information Centellis 4100 Getting Started 6806800E18B Installing the ATCA F120 Blade Damage High humidity and condensation on the blade surface causes short circuits Do not operate the blade outside the specified environmental limits Make sure the blade is completely dry and there is no moisture on any surface before applying power Do not operate the blade below 5 C Table 5 1 Environmental Requirements Requirement Temperature Operating 5 C 41 F to 40 C 104 F normal operation according to NEBS Standard GR 63 CORE 5 C 23 F to 55 C 131 F exceptional operation according to NEBS Standard GR 63 CORE Non Operating 40 C 40 F to 70 C 158 F may be further limited by installed accessories Temp Change 0 25 C min according to NEBS Standard GR 63 CORE 0 25 C min Rel Humidity 5 to 90 non condensing according to Artesy
158. tblende Die RJ 45 Stecker an der Frontblende werden f r verschiedene Schnittstellen verwendet die nicht verwechselt werden d rfen Wenn Sie ein Telefon oder ein E1 T1 Netzwerk an eines der mit COM gekennzeichneten seriellen Stecker anschlie en oder wenn Sie ein serielles Ger t an die mit E1 T1 gekennzeichneten Stecker anschlie en kann das Telefon oder das RTM besch digt werden Schlie en Sie deshalb nur E1 T1 Netze an die mit E1 T1 gekennzeichneten Stecker an und schlie en Sie nur serielle Ger te an die mit COM gekennzeichneten Stecker an Umweltschutz Entsorgen Sie alte Batterien und oder Blades Systemkomponenten RTMs stets gem der in Ihrem Land g ltigen Gesetzgebung und den Empfehlungen des Herstellers 108 Centellis 4100 Getting Started 6806800E18B Chapter 1 Introduction SE ee 1 1 1 2 Overview This Getting Started Guide is intended to enable you to install and start up the Centellis 4100 for the first time It furthermore provides a brief overview of the main features of the Centellis 4100 The structure of this guide reflects the main steps that you need to take in order to install and start up the Centellis 4100 The complete documentation of the Centellis 4100 related blades accessories as well as software packages can be downloaded from the Artesyn Embedded Technologies website For further details refer to Appendix A Related Documentation Check the Artesyn website or consult your local Artesyn s
159. ten Sie deshalb bis die Hot Swap LED blau leuchtet bevor Sie das Board herausziehen Besch digung von Schaltkreisen Elektrostatische Entladung und unsachgem er Ein und Ausbau des Produktes kann Schaltkreise besch digen oder ihre Lebensdauer verk rzen Bevor Sie das Produkt oder elektronische Komponenten ber hren vergewissern Sie sich da Sie in einem ESD gesch tzten Bereich arbeiten Fehlfunktion des Produktes Fehlerhafter Ein und Ausbau des Produktes kann zur Besch digung des Produktes f hren Stellen Sie deshalb sicher dass das Produkt mit allen Steckern mit der Systembackplane verbunden ist und ber alle Zone 1 Anschl sse mit Spannung versorgt wird Besch digung des Produktes Fehlerhafte Installation des Produktes kann zu einer Besch digung des Produktes f hren Verwenden Sie die Handles um das Produkt zu installieren deinstallieren Auf diese Weise vermeiden Sie dass das Face Plate oder die Platine deformiert oder zerst rt wird Besch digung des Produktes und von Zusatzmodulen Fehlerhafte Installation von Zusatzmodulen kann zur Besch digung des Produktes und der Zusatzmodule f hren Lesen Sie daher vor der Installation von Zusatzmodulen die zugeh rige Dokumentation Besch digung des Boards Hohe Luftfeuchtigkeit und Kondensat auf der Oberfl che des Boards k nnen zu Kurzschl ssen f hren Betreiben Sie das Board nur innerhalb der angegebenen Grenzwerte f r die relative Luftfeuchtigkeit und Temperatur
160. tesyn ATCA F120 blade Damage of Circuits Electrostatic discharge and incorrect RTM installation and removal can damage circuits or shorten their life Before touching the RTM or electronic components make sure that you are working in an ESD safe environment 144 Centellis 4100 Getting Started 6806800E18B Installing the RTM ATCA F120C 4 4 1 Installing the RTM Installation Procedure The following procedure describes the installation of the RTM 1 Locate the slot the RTM is to be installed into the shelf s rear which must be the same as that of the front blade 2 Ensure that the top and the bottom handles of the RTM are in an outward position by squeezing the lever and the latch together 3 Insert the RTM into the shelf by placing the top and bottom edges in the card guides of the slot 4 Slide the RTM into the slot 5 Apply equal and steady pressure to the RTM to carefully slide the RTM into the shelf until you feel resistance Continue to gently push the RTM until the RTM connectors engage 6 Squeeze the lever and the latch together and hook the lower and the upper handle into the shelf rail recesses Centellis 4100 Getting Started 6806800E18B 145 Installing the RTM ATCA F120C 7 Fully insert the RTM and lock it to the shelf by pressing the two components of the lower and the upper handles together and turning the handles toward the face plate 8 Tighten both face plate screws on the RTM
161. the operation of the equipment in your operating environment Failure to comply with these precautions or with specific warnings elsewhere in this manual could result in personal injury or damage to the equipment Artesyn intends to provide all necessary information to install and handle the product in this manual Because of the complexity of this product and its various uses we do not guarantee that the given information is complete If you need additional information ask your Artesyn representative The product has been designed to meet the standard industrial safety requirements It must only be used in its specific area of office telecommunication industry industrial control and development It must not be used in safety critical components life supporting devices or on aircraft Only personnel trained by Artesyn or persons qualified in electronics or electrical engineering are authorized to install remove or maintain the product The information given in this manual is meant to complete the knowledge of a specialist and must not be used as replacement for qualified personnel Keep away from live circuits inside the equipment Operating personnel must not remove equipment covers Only factory authorized service personnel or other qualified service personnel may remove equipment covers for internal subassembly or component replacement or any internal adjustment Do not install substitute parts or perform any unauthorized modification of
162. tic discharge and incorrect RTM or blade installation and removal can damage circuits or shorten their life Before touching the RTM blade or electronic components make sure that you are working in an ESD safe environment Installation Sequence of RTMs and AdvancedTCA Blades If you are going to install an RTM and an AdvancedTCA blade you have to regard the following Centellis 4100 Getting Started 6806800E1 8B 21 Centellis 4100 Shelf Safety Notes 22 sequence First install the RTM then install the matching AdvancedTCA blade Otherwise the blades and RTMs will be damaged Blade or System Damage Installing a blade in the wrong slot causes blade or system damage Only install blades in the designated slots Damage of RTM and Front Blade Removing the RTM from the system while the playload of the front blade is powered up may damage the front blade and RTM Whenever removing the RTM from the system you have to power down the playload of the front blade first RTM Malfunctioning Incorrect RTM installation and removal can result in RTM malfunctioning When plugging the RTM in or removing it do not press on the face plate but use the handles RTM Damage Installing the RTM with other blades than the ones designed for it may damage the RTM and the front blade Only install the RTM with the correct front blade Data Loss Removing the RTM with the system power on and the blue LED on the front blade still flashing causes data lo
163. tra low voltage circuits SELV circuits Centellis 4100 Getting Started 6806800E1 8B 65 ATCA F120 Safety Notes If in doubt ask your system administrator AMC Modules AMC Module Damage The two AMC bays only support AMC types modules which are officially supported by Artesyn AMC modules installed into AMC bay 1 or 4 must not exceed a power dissipation of 35W Installing and operating other AMC modules may damage the AMC modules the blade and an installed RTM including attached devices Only install AMC modules into AMC bay B1 and B4 which are officially supported by Artesyn Consult your local Artesyn sales representative if in doubt Limitation of Operating Temperature Range Installing AMC modules with small operating temperature ranges into the ATCA F120 may further restrict the operating temperature range of the ATCA F120 Make sure that the operating temperature of any installed AMC modules and the ATCA F120 as a bundle are within allowed limits Poor Shelf Cooling and EMC Compliance Violation An empty AMC bay may result in poor shelf cooling and strong EMC radiation and thus lead to EMC compliance violation Therefore always cover empty or unused AMC bays with a filler panel Environment Always dispose of used blades system components and RTMs according to your country s legislation and manufacturer s instructions 66 Centellis 4100 Getting Started 6806800E18B ATCA F120 Sicherheitshinweise Je Dieses K
164. treiben Sie das Produkt nur innerhalb der angegebenen Grenzwerte f r die relative Luftfeuchtigkeit und Temperatur Stellen Sie vor dem Einschalten des Stroms sicher dass sich auf dem Produkt kein Kondensat befindet Centellis 4100 Getting Started 6806800E1 8B 99 RTM ATCA 7221 FC Sicherheitshinweise berhitzung und Besch digung des RTMs Betreiben Sie das RTM ohne Zwangsbel ftung kann das RTM berhitzt und schlie lich besch digt werden Bevor Sie das RTM betreiben m ssen Sie sicher stellen dass das Shelf ber eine ausreichende Zwangsk hlung verf gt Wenn Sie das RTM in Gebieten mit starker elektromagnetischer Strahlung betreiben stellen Sie sicher dass das RTM mit dem System verschraubt ist und das System durch ein Geh use abgeschirmt ist Stellen Sie sicher dass Anschl sse und Kabel des RTMs w hrend des Betriebs nicht versehentlich ber hrt werden k nnen RJ 45 Stecker Laser Besch digung des RTMs und des Telefons RJ 45 Stecker an der Frontblende Die RJ 45 Stecker an der Frontblende werden f r verschiedene Schnittstellen verwendet die nicht verwechselt werden d rfen Wenn Sie ein Telefon oder ein E1 T1 Netzwerk an eines der mit COM gekennzeichneten seriellen Stecker anschlie en oder wenn Sie ein serielles Ger t an die mit E1 T1 gekennzeichneten Stecker anschlie en kann das Telefon oder das RTM besch digt werden Schlie en Sie deshalb nur E1 T1 Netze an die mit E1 T1 gekennzeichneten Stecker an und s
165. uipment covers for internal subassembly or component replacement or any internal adjustment Do not install substitute parts or perform any unauthorized modification of the equipment or the warranty may be voided Contact your local Artesyn representative for service and repair to make sure that all safety features are maintained This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Centellis 4100 Getting Started 6806800E1 8B 45 ATCA M100 Safety Notes Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Changes or modifications not expressly approved by Artesyn could void the user s authority to operate the equipment Board products are tested in a representative system to show compliance with the above mentioned requirements A proper installation in a compliant system will maintain the required performance Use only shielded cables when connecting peripherals to assure that appropriate radio freque
166. ule welche offiziell von Artesyn unterst tzt werden Installierte AMC Module d rfen eine Verlustleistung von 35W nicht berschreiten Die Installation und der Betrieb anderer AMC Module kann sowohl die AMC Module als auch das Blade sowie ein installiertes RTM und andere angeschlossene Ger te besch digen Installieren Sie daher nur AMC Module welche von Artesyn offiziell unterst tzt werden Wenden Sie sich bei Fragen an Ihren lokalen Artesyn Ansprechpartner Eingeschr nkte Betriebstemperaturbereich Werden AMC Module auf dem Blade installiert deren Betriebstemperaturbereiche kleiner sind als der Betriebstemperaturbereich des Blades selber so f hrt dies zu einer Einschr nkung des Betriebstemperaturbereiches des Blades Stellen Sie sicher dass sich die Betriebstemperaturbereiche des Blades sowie installierter AMG Module innerhalb erlaubter Bereiche bewegen Verletzung von EMV Grenzwerten und verminderte K hlung des Shelfs Ein leerer AMCSteckplatz kann zu verminderter K hlung des Shelfs sowie starker elektromagnetischer Strahlung f hren und somit eine berschreitung von EMV Grenzwerten zur Folge haben Installieren Sie daher immer ein Filler Panel in einen anderweitig nicht verwendeten AMG Steckplatz Umweltschutz Entsorgen Sie alte Blades Systemkomponenten RTMs stets gem der in Ihrem Land g ltigen Gesetzgebung wenn m glich immer umweltfreundlich 72 Centellis 4100 Getting Started 6806800E18B RTM ATCA F120C Safety
167. ull the rubber boots over the nuts Centellis 4100 Getting Started 6806800E18B 201 Starting up the System eee A 11 Once the new PEM is installed and connected turn on the feed power PEM Damage Applying reversal power causes damage to the electrolytic capacitors of the filter Therefore only switch on the breakers if no red light is visible 12 If the red LED is ON turn off the feed power reverse power and turn on the feed power 202 Centellis 4100 Getting Started 6806800E18B Starting up the System 13 When the red LED stays OFF push the breaker to the ON position the red portion will no longer be visible on the top of the breaker Centellis 4100 Getting Started 6806800E18B 203 Starting up the System 14 If you want to inform shelf management about the PEM insertion place the PEM handle switch to the Closed position The blue LED starts to blink This indicates that the PEM announces its presence to the shelf management controller Wait until the blue LED is switched OFF The switched off blue LED indicates that the PEM is active 1y Evenwithout applying power to the PEM the IPMC will power up and the blue H S LED will be on steady This is because the system receives power from the other PEM 204 Centellis 4100 Getting Started 6806800E18B Starting up the System eee EEE 15 Query the shelf manager to ensure the PEM is operating properly Centellis 4100 Getting Sta
168. until the blue LED is permanently ON RTM Damage Installing the RTM with other blades than the ATCA 7221 damages the RTM Only install the RTM with the Artesyn ATCA 7221 blade Operation Product Damage Surface High humidity and condensation on the product surface causes short circuits Do not operate the product outside the specified environmental limits Make sure the product is completely dry and there is no moisture on any surface before applying power RTM Overheating and RTM Damage Operating the RTM without sufficient forced air cooling may lead to RTM overheating and thus Centellis 4100 Getting Started 6806800E1 8B 103 RTM ATCA 7221 SCS Safety Notes RTM damage When operating the RTM make sure that sufficient forced air cooling is available in the shelf When operating the RTM in areas of electromagnetic radiation ensure that the RTM is bolted on the system and the system is shielded by enclosure Make sure that contacts and cables of the RTM cannot be touched while the RTM is operating RJ 45 Connector RTM and Telephone Damage E1 T1 interfaces on face plate On the face plate RJ 45 connectors are used for different interfaces Mismatching the interfaces i e connecting a telephone or an E1 T1 network to the serial interfaces labeled as COM or connecting a serial device to a RJ 45 connector labeled as E1 T1 may damage the telephone or the RTM Therefore only connect E1 T1 networks to RJ 45 connectors labeled as E1
169. w 0 C Injury Caution this unit has four 48V to 60 V DC feeders All must be disconnected to de energize the system To reduce the risk of injury disconnect the feeders when removing power from the system System Damage Air Filter Air contamination can pollute the air filter and obstruct the air intake of the system which may cause system overheating and component damage To guarantee proper airflow through the system the air filter has to be replaced at least every six months Artesyn recommends to replace the air filter every 90 days Filter replacement frequency depends on the environment the system is subjected to Air filters should be cleaned at least every 90 days or sooner depending on the conditions of the environment Because central offices vary in physical location and cleanliness check your air filters every week after you first install your system In a dusty environment a filter may need cleaning more often than a filter in a cleaner environment Check the filters frequently Centellis 4100 Getting Started 6806800E1 8B 23 Centellis 4100 Shelf Safety Notes 24 until you have a good idea of how often it needs cleaning Based on your findings establish a regular cleaning schedule and keep a log to record the date of each filter cleaning or replacement This equipment is designed to permit the connection of the earthed conductor of the DC supply circuit to the earthing conductor at the equipment If this connection
170. werden und genug Raum f r die Luftzirkulation vorhanden ist Verletzungsgefahr und Besch digung des Systems Das System ist an eine TNV 2 Spannungsquelle angeschlossen Diese Spannung kann gef hrlich sein Stellen Sie sicher dass die externe Spannungsversorgung den entsprechenden Sicherheitsstandards entspricht System berhitzung Unzureichende K hlung kann zu einer Besch digung der Boards f hren Um eine ausreichende K hlung sicherzustellen betreiben Sie das System nur aufrecht Sorgen Sie au erdem daf r dass ein aureichender Mindestabstand mindestens 6 cm vor den L ftungsschlitzen an der Vorder und R ckseite des Systems freigehalten wird Genaue Informationen finden Sie im Kapitel Site Planning Considerations on page 117 Verletzungsgefahr und Besch digung des Systems Wenn die Gewichte im Schaltschrank ungleich verteilt sind kann der Schaltschrank umkippen Bauen Sie das System deshalb ganz unten im Schrank ein wenn es das einzige System im Schrank ist Wenn mehrere Systeme in einen Schrank eingebaut werden sollen plazieren Sie das schwerste System ganz unten und die leichteren weiter oben Falls der Schaltschrank mit Kippsicherungen ausgestattet ist stellen Sie sicher dass diese auch installiert und ausgefahren sind um einen sicheren Stand des Schranks zu gew hrleisten Beginnen Sie erst danach mit dem Einbau oder der Wartung des Systems Verletzungsgefahr oder Besch digung des Systems Das System kann beim Herausz

Centellis 4100 Getting Started Guide

Contents

Download Pdf Manuals

Related Search

Related Contents