Samsung AWT24QPHBB User Manual
Contents
1. on the unit button The timer is not correctly triggered Check that the timer has been programmed correctly see page 11 13 Odour is permeated in the Airthe room room during air conditioning Technical Specifications Design and specifications are subject to change without notice Model Power Supply AWT18QPHBB 220V 60Hz AWT24QPHBB AWT18QPHEB 220 240V 50Hz AWT24QPHEC Method of Installation Before installation be sure to check the installation area or the air conditioner and drain hose Checkpoints prior to installation 1 Check the cabinet and front grille of the unit for any harmful defects Such as scratches 2 Be sure to check the power supply Refer to the specifications on the label attached to the unit Installation Conditions 1 Asthe unit is heavy the wall or window of the installation area should have sufficient strength and durability for operation of the air conditioner and for prevention of any vibration or noise If it is weak reinforcement work should be performed separately 2 It is advisable to install the air conditioner in the north or west side to prevent the effect of direct sunlight When installing it in the south or east side due to unavoidable circumstances it is advisable to install the sunshade to prevent the direct sunlight In this case take care not to cause any hindrance to the flow of outside air 3 When installing the air conditioner be sure to2. 16 a Solving Common Problems a Technical Specifications pp METHODOF INSTAELATION iiec toe re dee a 19 CAUTION The high inrush current of the starting compressor motor can have adverse effects to the operation of other equipment under unfavorable mains conditions This equipment does not comply with the relevant technical standards for the limitation of voltage fluctuations and flicker Before connecting this equipment to the power supply system please report to your supply authority and obtain the consent Do not connect other electric appliances to the same supply lines Description of Each Component Airinlet Inside Air filter Inside Operating mode indicators Cool Fan Dry Mode selection button Cool Fan Dry Energy Saver indicator Energy Saver button Sleep timer indicator Sleep timer Setting button Timer setting button Em al SM NN F1 Low F2 Med F3 High Fan speed adjustment button S SS SS MSP BLUE BROWN YELLOW GREEN Main Power Earth Inner air flow blades right left orientation Outer air flow blades up down orientation Air inlet Outside Air outlet Ventilation lever 3 Power cable connection should be committed to an installation engineer Temperature Timer settings Temperature adjustment buttons Timer indicator Ai
3. being X Plugged in Stopped It will start up automatically after about three minutes 2 If the COOL indicator is not lit up on the unit Press the button on the remote control or Press the button on the unit one or more times until the COOL indicator lights up P Result The unit beeps each time you press the amp button The air conditioner starts up in Cool mode gt You can change modes at any time 3 To adjust the temperature press the CGAY or GVA button on the remote control one or more times until the required temperature is displayed To adjust the temperature press the LE or W button on the unit one or more times until the required temperature is displayed Possible temperatures are between 18 C and 30 C inclusive Result Each time you press the temperaure bottons The temperature is adjusted by 1 C and displayed on the control panel The unit beeps The air conditioner starts cooling if the room temperature is higher than the selected temperature 4 To set the fan speed to Then Press the ved or button on the remote control as desired or Press the button on the unit one or more times until the the desired fan speed F1 F2 or F3 is displayed Low Speed F e Med Speed F 3 High Speed 5 Tocontrol the direction of the air flow refer to page 10 AiringYour Room If the atmosphere in your room is stale you can air it using the Fan fe
4. tlie OWNER S INSTRUCTIONS AWT18QPHBB AWT24QPHEC Window type Room Air Conditioner Cool at Ih M w W i Y EX amp DB98 23028A 1 Register your product at www samsung com global register Safety Precautions The following safety precautions must be taken when using your air conditioner N WARNING DURING OPERATION DISPOSING OF THE UNIT OTHERS Risk of electric shock e Can cause injury or death e Disconnect all remote electric power supplies before servicing installing or cleaning e This must be done by the manufacturer or its service agent or a similar qualified person in order to avoid a hazard Users of this product are cautioned not to attempt repair of this product at their own discretion Instead they are requested to directly contact a designated service center or the outlet at which the product was purchased Never spill any kind of liquid into the unit Should this happen unplug or main Switch off the unit and contact an authorized service center Do not insert anything between the air outlet blades because the inner fan may be damaged and could cause injury Keep children away from the unit Do not place any obstacles in front of the unit Do not spray liquid of any kind into the indoor unit Should this happen switch off the breaker used for your air conditioner and contact your installation specialist Make sure that the unit is correctly ventilated at all times D
5. Power press the 5 On Off button Q 2 Set the operating time by pressing on the remote control or onthe unit one or more times Possible times is between 1 hour and 24 hours inclusive Result The remaining time is displayed and decreased by 1 hour automatically to indicate the remaining time Es The air conditioner switches off automatically when the operating time reaches zero Fi Low F2 Med F3 High 2 You can change the setting mode fan speed and air flow direction after setting the Off Timer To Cancel the Off Timer To cancel the Off Timer press on the remote control or amp on the unit one or more times until ge is displayed or b onthe remote control or unit The air conditioner operates in the mode selected when the unit was last used x button on the unit Fan speed 4 button on the Remote control m Setting the SleepTimer The Sleep Timer can be used when you are cooling your room to switch the air conditioner off automatically after a period of 8 hours Remote Control Control Panel gt If you wish to switch the unit off at a specific time refer to page 12 Power 1 Make sure that you have selected either COOL mode 2 Press the button on the remote control e e Press the button on the unit until the 3 indicator lights Result Eachtime you press a butoon the unit beeps The 3 indicator and E will be
6. illustrations have a Remote control Gray background Example Unit itself White background Example Inserting the Remote Control Batteries You must insert or replace the remote control batteries when You purchase the air conditioner The remote control does not work correctly ag Use two AAA LRO3 1 5 V batteries Do not use old batteries or different kinds of batteries together Batteries may be completely discharged after 12 months even if they have not actually been used 1 Push the battery cover on the rear of the remote control with your thumb in the direction of the arrow and remove it 2 Insert the two batteries taking care to respect the polarities onthe battery with on the remote control onthe battery with on the remote control 3 Close the cover by sliding it back until it clicks into place Result You can control all the functions on your air conditioning unit directly from your seat using the remote control CoolingYour Room Remote Control Control Panel Power You must select the Cool mode if you wish to lower the temperature in your room Y ou can also set the fan speed 1 If necessary press the On Off button Result The air conditioner starts up in the Cool mode The unit beeps twice Gag The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after
7. obtain sufficient space on the rear side of the unit for smooth flow of air When operating the air conditioner in closed areas such as inner building with cooling operation and result in trouble with the unit See the illustration below C Awning joo ad o9O0o 60 000 e O Oo o Fence wall or other obstacle J oC 0000 Qo 1 Approx 3 6 0000 09 150mm min 90o 909 0 0 Q0200 20 0 Q0Q200 90o9o090 09 96060 050 696060 05 26 6 JooQQooO9590o0Q Los J oo 0050000 0o0o0 00o09590 0000005200000005 90 000006 If the wall is greater than 150mm thick cut the wall back on a 45 angle if possible MODEL A AWT18 AWT24 260 Method of Installation cont Installation of the Drain Tube Fix the drain tube as shown in the figure Drain Tube Installation of the Drain Pan The procedure for installing the drain pan should be determined by the condition of the installing area In the case of an area where the drain pan can not be directly installed on the rear side of the unit after installing the air conditioner Example High storage 1 Open the front grille CAUTION Removal and Reassembly of the Front Grille 1 Grasp the lower part of t
8. the right hand side of the unit thus increasing the efficiency of the air conditioner Remote Control Control Panel 1 Press the Gor onthe unib button the remote control Result The inner blades swing automatically left and right gt Inthe Energy Saving mode the blades may stop when the compressor is off For details on the Energy Saving mode refer to page 14 2 To stop the blades moving left and right press the 5 or e on the unit button in the remote control 2 Tostop the blades in a specific position and orient the air flow in the corresponding direction simply press the 5 or onthe unit button on the remote control when the blades are in the desired position Adjusting the Air Flow Direction Vertically Again depending on the position of the unit in your room you can adjust the orientation of the outer air flow blades on the right hand side of the unit RECOMMENDATION When Adjust the blades to face Bii ao HE Cooling Upwards z Adjust the air flow blades to the desired position by pushing them upwards or downwards 9 5 BA BE a A ZG BE ZG 22 gt Ifyou orient the air flow blades downwards and the unit operates in Cool mode for a long period of time dew may From on the surface of the blades Drip from the blades Setting the On Timer The On Timer enables you to switch on the air conditioner automatically after a given period time You can s
9. Removal and Reassembly of the Front Grille 1 Grasp the lower part of the front grille and the air filter handle then open the grille The open angle of front grille has not to be exceeded 90 degree 2 Lift the front grille slightly and remove it from the front panel 3 Reassembling of front grille should be done in reverse order of disassembly Front grille Grille groove 2 Pull the air filter to the right side Body guide 3 Remove all dust on the air filter with a vacuum cleaner or brush 4 When you have finished insert the air filter back into its original position 5 Wipe the surface of the unit with a neutral detergent and then wipe it again with dry cloth Be sure not to use benzene solvent or other chemical products The air conditioner has two or three grille gt f you Then grooves depending on the model Will not be using the Set the fan going for three to four hours air conditioner for a to dry the inside of the air conditioner long period of time thoroughly Switch the air conditioner off and unplug it from the wall socket Clean the filter and outer surfaces Have not used the air Setthe fan going for a few hours to conditioner for a long dry the inside of the air conditioner period of time thoroughly Solving Common Problems Before contacting the after sales service perform the following simple checks They
10. ature and if necessary evacuate the stale air outside 1 If you wish to evacuate stale air outside push the ventilation lever on the front of the unit to the right and the open position 1T Result The air inside the room circulates and stale air is evacuated outside Otherwise push the ventilation lever to the left and the closed position Result The air simply circulates inside the room 2 If necessary press the 5 On Off button Result The air conditioner starts up in the Cool mode The unit beeps twice 3 If the FAN indicator is not lit up on the unit 9 Press the button on the remote control or R Pressthe button on the unit one or more times until the FAN indicator lights up Result The unit beeps each time you press the Ga amp button The air conditioner starts up in Cool mode gt You can change modes at any time When the air conditioner is in the Fan mode the temperature is not displayed in this case you do not need to set the temperature 4 To set the fan speed Then Pressthe Ke or 2 button on the remote control as desired or Pressthe button on the unit one or more times until the the desired fan speed F1 F2 or F3 is displayed F Low Speed Fe Med Speed F3 High Speed 5 To control the direction of the air flow refer to page 10 Remote Control Control Panel Power Removing Excess Humidity If the atmos
11. displayed The remaining time is displayed and decreased by 1 hour automatically to indicate the remaining time The air conditioner will be controlled as illustration below Cooling When the temperature has been increased by 1 C after 1 hour it is maintained vcl for 7 hours Set TEMP ihr 8hr Start Stop time time FLLow PFMed F3High To Cancel the SleepTimer To cancel the timer press on the remote control or e e on the unit Result The unit beeps The Z indicator is no longer displyed The air conditioner operates in the mode selected last gt If you select the Energy Saving mode in the Sleep Timer mode the Sleep Timer will be cancelled and the air conditioner will start up in the Energy Saving mode Selecting Energy Saving Mode If you wish to save Energy when using your air conditioner select the Energy Saving mode with the Energy Saver button Remote Control Control Panel 1 Toselectthe Energy Saving mode press the Energy Saver button on the remote control or unit one or more times until the Energy Saver indicator lights up Result The fan and compressor cycle on and off together The fan will continue to run for a short time after the compressor cycles off gt fyou would like the air conditioner to run in Fan mode do not press the Energy Saver button Y ou cannot use the Fan mode in the Energy saving mode 2 To stop the Energy Sav
12. e of the packaging material for this product in an environmentally responsible manner Never store or ship the air conditioner upside down or sideways to avoid damage to the compressor The appliance is not intended for use by young children or infirm persons without supervision Young children should be supervised to ensure that they do not play with the appliance Max current is measured according to IEC standard for safety and current is measured according to ISO standard for energy efficiency Contents PREPARING YOUR AIR CONDITIONER w Safety Precautions ood rei i toe ae 2 a Air Conditioning Unit Main Parts Buttons and Display 4 a Remote Control Buttons 5 a Getting Started pp ws 6 a Inserting the Remote Control Batteries pp 7 OPERATING YOUR AIR CONDITIONER a Cooling Your ROOM seinien eet oh genet ia i Airing Your Room a Removing Excess Adjusting the Air Flow Direction Horizontally a Adjusting the Air Flow Direction Vertically pp PROGRAMMING YOUR AIR CONDITIONER Setting the On TIM AE E ates a Setting the Off Timeline ant el at be eee ct coe DO te dee e oe nd a Setting the Sleep Timer Selecting Energy Saving mode RECOMMENDATIONS FOR USE a Temperature and Humidity Ranges pp 15 a Cleaning Your Air Conditioner
13. et the period of time from 1 hour to 24 hours Remote Control Control Panel You can select the On Timer only when the air conditioner is off Power 1 Check that the air conditioner has been switched off if necessary press the D button 2 Setthe operating time by pressing on the remote control or amp onthe unit one or more times Possible time is between 1 hour and 24 hours inclusive Result The remaining time is displayed and decreased by 1 hour See automatically to indicate the remaining time The air conditioner switches on automatically when the operating time reaches zero gt You can change the setting mode fan speed and air flow direction after setting the On Timer To Cancel the On Timer To cancel the On Timer press on the remote control or amp on the unit one or more times until EE is displayed or On Off button on the remote control or unit The air conditioner operates in the cool mode Fenspeea e button on the unit Flow Fad FI Hh button on the Remote control Setting the OffTimer The Off Timer enables you to switch off the air conditioner automatically after a given period of time You can set the period of time from 1 hour to 24 hours Remote Control You can select the Off Timer only when the air conditioner is on cmo e onito Control Panel 1 Check that the air conditioner has been switched on if necessary
14. he front grille and the air filter handle then open the grille The open angle of front grille has not to be exceeded 90 degree 2 Push the front grille on the left and remove it from the front panel 3 Reassembling of front grille should be done in reverse order of disassembly 2 Remove the front panel 2 1 Press both sides of the cabinet in the direction of the arrow as shown in the figure 2 2 Pull the lower part of the front panel slightly forward below three inches 2 3 Lift the front panel upward Han IS c 5 221 Applying excessive force to remove the front panel may cause damage to the tab be sure not to use excessive force 3 Remove four screws on the lower right and left sides of the unit Method of Installation cont 4 Remove the chassis from the cabinet 5 Remove the rubber cap inserted into the basepan 6 Fixthe drain pan as shown in the figure and then connect the drain hose You can use any commercially available drain hose 7 Install the cabinet at the specified area after installing the drain pan and then re assemble it in the original condition When assembling the front panel be sure to fix with a supplied screw TH 28 4X10 In the case of an area where the drain pan can be directly installed on the rear side of the unit after installing the air conditioner 1 F
15. ing mode press the Energy Saver button on the remote control or unit again Result The fan runs at all times while the compressor cycles on and off gt If you select the Sleep Timer in the Energy Saving mode the Energy Saving will be cancelled and the air conditioner will start up in the Sleep Timer mode Temperature and Humidity Ranges The following table indicates the temperature and humidity ranges within which the air conditioner can be used Mode Indoor Temperature Outdoor Temperature Indoor Humidity Cooling 21 C to 32C approx 21 C to 54 C approx 80 or less If the air conditioner is used at Then Higher temperatures The automatic protection feature may be triggered and the air conditioner stopped Lower temperatures A water leakage or some other malfunction may happen if the heat exchanger freezes Higher humidity levels Water way condense on and drip from the surface of the unit if it is used for long periods CleaningYour Air Conditioner Be sure to clean the air filter periodically two weeks to maintain the air conditioner in the best condition for a long period of time PORTANT When cleaning the air conditioner turn it off and pull out the power plug 1 Hold the front grille handle slightly pull it to the left side and open the front grille gt The removal of the front grille makes it easier to clean the air conditioner Open the grille as much as possible CAUTION
16. may save you the time and expense of an unnecessary service call Problem Explanation Solution The air conditioner does not Check that the circuit breaker used for the air conditioner has not operate at all been triggered Check that the power cable is plugged into a wall socket and the socket is switched on if necessary Check that the operating mode indicator COOL or FAN on the unit is lit up if necessary press On Off button on the remote control or unit The air conditioner does not Check that there are no obstacles between you and the unit operate with the remote control Replace the remote control batteries if necessary Check that you are close enough to the unit seven metres yards or less No beep is heard when you press Check that you are pointing the remote control at the remote 5 On Off on the remote control control sensor on the unit Replace the remote control batteries if necessary The air conditioner does not cool Check that the correct operating mode has been selected COOL The room temperature may be too low Dust may be blocking the air filter refer to page 16 for cleaning instructions Check that there is no obstacle blocking the air flow into or out of the unit The air flow direction does not Check that the air conditioner has been switched on if necessary change when you press the press On Off button on the remote control or unit or
17. o not place clothing or other materials over it If the wireless remote control will not be used for a long time remove the batteries If applicable When using a wireless remote control the distance should not be more than 7 meters from the air conditioner If applicable The air conditioner must be plugged into its own specific power source which must be installed in compliance with national wiring earthing and safety regulations If the power cord is damaged in any way it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard This device must be installed according to the national electrical rules The appliance must be installation that the plug should be easily accessible after installation If the fuse on PC board is broken please change it with the type of T 3 15A 250V The breaker of the air conditioner should be all pole switch and the distance between its two contacts should be no less than 3 5mm Such means for disconnection must be incorporation in the fixed wiring Before throwing out the device it is necessary to pull back the battery cells and get rid of them safely for recycling reasons When you need to dispose of the unit consult your dealer If pipes are removed incorrectly refrigerant may blow out and come into contact with your skin causing injury Releasing refrigerant into the atmosphere also damages the environments Please recycle or dispos
18. ollow steps 5 and 6 only If the air conditioner has accessory seal please install the seal as shown in the figure Installation of the accessory seal Except AWT12 Seal Cabi Side T40 W50 L430 Qty 2 Seal Cabi Top T30 W40 L700 Qty 1 Seal Base T10 W30 L630 Qty 1 Drain Pan MER cap Screw Drain Hose Bottom Side View with Drain Pan and Hose in Place 7 MULT Up EE m Screw SEAL BASE SEAL CABITOP SEAL CABI SIDE SEAL CABI SIDE THIS AIR CONDITIONER IS MANUFACTURED BY Lm ELECTRONICS
19. phere in your room is very humid or damp you can remove excess humidity without lowering the room temperature too much Remote Control Control Panel 1 If necessary press the On Off button Power Result The air conditioner starts up in the Cool mode The beeps GM The air conditioner is fitted with a protection mechanism to pre vent the unit from being damaged when it is started immediately after being Plugged in Stopped It will start up normally after three minutes 2 If the temperature is not displayed at the top of the control panel press the button the control panel one or more times until it appears Result The unit beeps each time you press the e button The air conditioner runs in Dry mode gt You can change modes at any time 3 To adjust the temperature press the M or W buttons one or more times until the required temperature is displayed Possible temperatures are between 18 C and 30 C inclusive Result Each time you press the M or W buttons The temperature is adjusted by 1 C The unit beeps The air conditioner starts removing the excess humidity the quantity of air is adjusted automatically D Temp 4 To control the direction of the air flow refer to page 11 Adjusting the Air Flow Direction Horizontally Depending on the position of the unit in your room you can adjust the orientation of the inner air flow blades on
20. r flow blade swing button On Off button Remote control signal receiver Remote Control Buttons Timer setting button Temperature adjustment buttons Sleep timer setting button Operating mode Fan speed adjustment selection buttons buttons Energy Saver button Swing Air flow blade swing button b Jd On Off button Getting Started You have just purchased a window type room air conditioner and it has been installed by your installation specialist Your Owner s Instructions contain valuable information on using your air conditioner Please take the time to read them as they will help you take full advantage of the unit s functions This Owner s Instructions is just for using your air conditioner correctly Thus the illustrations shown in this manual may not exactly match your air conditioners The booklet is organized as follows The following figures are shown on pages 4 and 5 Air conditioning unit main parts buttons and display Remote control buttons They will help you find the buttons and understand the symbols displayed In the manual you will find a series of step by step procedures for each function available The illustrations in the step by step procedures use four different symbols er gt IMPORTANT NOTE Moreover applicable wherever the illustrations show the positions of the buttons on both the remote control and the unit itself For the The
Download Pdf Manuals
Related Search