Samsung AWT24A7ME دليل المستخدم
Contents
1. f a power failure occurs when the air conditioner is operating the unit is switched off Then the power returns the air conditioner starts up again automatically and the restart indicator blinkes The indicator lights up after 2 minutes Only A8 G8 gt Remote Control Buttons Operating mode selection buttons Timer setting buttons FAN COOL Temperature adjustment buttons ON OFF Button Fan speed adjustment buttons Air flow blade swing button ENGLISH Getting Started You have just purchased a window type room air conditioner and it has been installed by your installation specialist Your Owner s Instructions contain valuable information on using your air conditioner Please take the time to read them as they will help you take full advantage of the unit s functions The booklet is organized as follows The following figures are shown on pages 4 and 5 Air conditioning unit main parts buttons and display Remote control buttons They will help you find the buttons and understand the symbols displayed 4 In the main part of the document you will find a series of step by step procedures for each function available The illustrations in the step by step procedures use four different symbols ag gt IMPORTANT NOTE Moreover applicable wherever the illustrations show the positions of the buttons on both the remote control and the unit itself For the The illustrations have a Remote2. Airing Your Room If the atmosphere in your room is stale you can air it using the Fan feature and if necessary evacuate the stale air outside 1 If you wish to evacuate stale air outside push the ventilation lever on the front of the unit to the right and the open position 3S Result The air inside the room circulates and stale air is evacuated outside Otherwise push the ventilation lever to the left and the closed position EF Result The air simply circulates inside the room 2 If necessary press the C On Off button Result The operating mode indicator COOL or FAN on the unit comes on 4 The air conditioner starts up in the mode selected when the unit was last used 4 The unit beeps twice 3 If the FAN indicator is not lit up on the unit Press the C button on the remote control or Press the MODE button on the unit one or more times until the FAN indicator lights up Result 4 The unit beeps each time you press MODE The air conditioner starts up in Fan mode gt Youcan change modes at any time When the air conditioner is in Fan mode the temperature is not displayed in this case you do not need to set the temperature 4 To set the fan speed to Then High Press the GJ button on the remote control Low Press the EE button on the remote control Result Each time you press a button the unit beeps 5 To control the direction of the air flow refer to page 10
3. OWNERS INSTRUCTIONS MANUAL DE INSTRUCCIONES MANUEL D UTILISATION MANUAL DE INSTRUCOES ISTRUZIONI PER LUSO AW07A7 G7 SA B D E AW09A7 G7 SA B D E AW08A7 G7 SA AW10A7 G7 JA B C D E AW12A7 G7 JA B C D E AW14A7 G7 JA B C D E AWT24A7 G7 MA B C D E AWT18A7 G7 MA B C D E AW24A7 G7 MA B C D E AW22A7 G7 MA B C D E AW21A7 G7 MA B C D E AW18A7 G7 MA B C D E AW22A7 G7 WA B C D E AW18A7 G7 WA B C D E AW14A7 G7 WA B C D E AW07A8 G8 SA B D E AW09A8 G8 SA B D E AW08A8 G8 SA AW10A8 G8 JA B C D E AW12A8 G8 JA B C D E AW14A8 G8 JA B C D E AWT24A8 G8 MA B C D E AWT18A8 G8 MA B C D E AW24A8 G8 MA B C D E AW22A8 G8 MA B C D E AW21A8 G8 MA B C D E AW18A8 G8 MA B C D E AW22A8 G8 WA B C D E AW18A8 G8 WA B C D E AW14A8 G8 WA B C D E ENGLISH Window type Room Air Conditioner Cool Acondicionador de aire dom stico sistema de tipo ventana Refrigeraci n Climatiseur de type Fen tre Refroidissement O ar Condicionado de Window Type Refrigera o Condizionatore d aria per ambienti da finestra Raffreddamento E E PD DB68 00526A 4 Safety Precautions The following safety precautions must be taken when installing and using your air conditioner 1 The air conditioner must be plugged into its own specific power source which must be installed in compliance with national wiring earthing and safety regulations Depending on national regulations and your specific installation you may need to install A cir
4. cap Drain Pan Drain Hose Bottom Side View with Drain Pan and Hose in Place THIS AIR CONDITIONER IS MANUFACTURED BY ESTE AIRE ACONDICIONADO HA SIDO FABRICADO POR CE CLIMATISEUR EST FABRIQUE PAR ESTE APARELHO DE AR CONDICIONADO E FABRICADO POR QUESTO CONDIZIONATORE D ARIA E PRODOTTO DA I ELECTRONICS Printed in Korea
5. control Gray background Example Unit itself White background Example a Inserting the Remote Control Batteries You must insert or replace the remote control batteries when You purchase the air conditioner The remote control does not work correctly ag Use two LRO3 R03 1 5 V batteries Do not use old batteries or different kinds of batteries together Batteries may be completely discharged after 12 months even if they have not actually been used 1 Push the battery cover on the rear of the remote control with your thumb in the direction of the arrow and remove it 2 Insert the two batteries taking care to respect the polarities 4 onthe battery with on the remote control onthe battery with on the remote control 3 Close the cover by sliding it back until it clicks into place Result You can control all the functions on your air conditioning unit directly from your seat using the remote control ENGLISH Cooling Your Room You must select the Cool mode if you wish to lower the temperature in your room You can also set the fan speed Remote Control Control Panel 1 If necessary press the CD On Off button Result 9 The operating mode indicator COOL or FAN on the unit comes on The air conditioner starts up in the mode selected when the unit was last used y POWER The unit beeps twice e The air conditioner is fitted with a protection mechanism to preven
6. the unit after installing the air conditioner Example High storage 1 Open the front grille refer to page 13 2 Remove the screw located at the lower section of the front grille It is secured in the C section depending on the model 3 Remove the front panel 3 1 Press both sides of the cabinet in the direction of the arrow as shown in the figure 3 2 Pull the lower part of the front panel slightly forward i below three inches 7cm 3 3 Lift the front panel upward om Applying excessive force to remove the front panel may cause damage to the tab be sure not to use excessive force 4 Remove two screws on the lower right and left sides of the unit 5 Remove the chassis from the cabinet 6 Remove the rubber cap inserted into the basepan 7 Fix the drain pan as shown in the figure and then connect the drain hose Drain Pan You can use any commercially available drain hose 8 Install the cabinet at the specified area after installing the drain pan and then re assemble it in the original condition F 2 Secure the front panel to the case by replacing the screw removed in ne ae Rubber cap Screw step 2 If a screw not removed in step 2 secure the panel with a ee The others supplied screw In the case of an area where the drain pan can be directly installed on the rear side of the unit after installing the air conditioner 1 Follow steps 6 and 7 only Rubber
7. until is displayed Result The unit beeps each time you press a button The Hr indicator on the unit switches off The air conditioner operates automatically Remote Control Control Panel ENGLISH Operating Recommendation Here is a recommendation that you should follow when using your air conditioner Topic Recommendation Power failure If a power failure occurs when the air conditioner is operating the unit is switched off When the power returns A7 G7 you must press On Off button to restart it A8 G8 the air conditioner starts up again automatically and the restart indicator blinkes for 2 minutes and then lights up Temperature and Humidity Ranges The following table indicates the temperature and humidity ranges within which the air conditioner can be used Mode Indoor Temperature Outdoor Temperature Indoor Humidity Cooling 21 C to 32 C approx 21 C to 43 C approx 80 or less If the air conditioner is used at Higher temperatures Then The automatic protection feature may be triggered and the air conditioner stopped Lower temperatures A water leakage or some other malfunction may happen if the heat exchanger freezes Higher humidity levels Water may condense on and drip from the surface of the unit if it is used for long periods Cleaning Your Air Conditioner To get the best possible use out of your air conditioner yo
8. ENGLISH Remote Control Control Panel POWE Ce Nr RESTART cooL FA O POWER 1 M N Adjusting the Air Flow Direction Horizontally Depending on the position of the unit in your room you can adjust the orientation of the inner air flow blades on the right hand side of the unit thus increasing the efficiency of the air conditioner Heme Come nero Panel 1 Press the D or Gon the unit button on the remote control Result The inner blades swing automatically left and right Ea Ga 2 To stop the blades moving left and right press the SP or GD on the unit SWING button on the remote control 4 gt To stop the blades in a specific position and orient the air flow in the corresponding direction simply press the D or Gion the unit button on the remote control when the blades are in the desired position Adjusting the Air Flow Direction Vertically Again depending on the position of the unit in your room you can adjust the orientation of the outer air flow blades on the right hand side of the unit RECOMMENDATION When Adjust the blades to face Cooling Upwards NN c A A A e Adjust the air flow blades to the desired position by pushing them upwards or downwards EB os Z A BZ A ZA Ze A ZZ Z FA Z Go 2A o gt Ifyou orient the air flow blades downwards and the unit operates in Cool mode for a long period of time
9. cuit breaker For further information on electrical requirements contact a professional electrician This air conditioner must be connected by a licenced electrician This device must be installed according to the national electrical rules 2 Make sure that the unit is correctly ventilated at all times do NOT place clothing or other materials over it 3 NEVER spill liquid of any kind into the unit Should this happen unplug the unit and contact your installation specialist 4 Do NOT insert anything between the air outlet blades as the inner fan may be damaged and you may be hurt Keep children away from the unit 5 ALWAYS ensure that the power cable is in good condition Make sure that it is not walked on or damaged by items placed on or against it If the power cord is damaged in any way it must be replaced by an approved power cord available from the manufacturer or its service agent 6 Do NOT attempt to repair the unit yourself If it is damaged in any way contact An approved service center The outlet at which the air conditioner was purchased 7 Do NOT place any obstacles in front of the unit 8 If the remote control will not be used for a long time remove the batteries 9 Before throwing out the device it is necessary to pull back the battery cells and get rid of them safely 10 The appliance is not intended for use by young children or infirm person without supervision young children sh
10. dew may Form on the surface of the blades Drip from the blades Switching the Unit Off Automatically Off Timer You can set the timer to switch the air conditioner off automatically at a given time Example You wish to switch the unit off two hours after you have gone to bed 1 If necessary press the On Off button 2 Select the required mode by pressing the appropriate button or on the remote control MODE button on the unit press it one or more times until the appropriate operating mode indicator lights up 3 Set the operating time by pressing TIMER A or Y on the remote control one or more times Example To switch the unit off two hours after you have gone to bed set the operating time to 2 hours Possible operating times are between 1 and 24 hours inclusive Result 4 The Hr indicator flashes for about ten seconds The operating time is displayed and decreased automatically to indicate the remaining time The air conditioner switches off automatically when the operating time reaches zero gt You can change your setting at any time Canceling the Off Timer Remote Control o Control Panel RESTART C FAN POWER zw TIMER GE ale SEINS If you no longer wish to use the Off Timer that you have set you can cancel it at any time To cancel the timer press TIMER A or V on the remote control one or more times
11. ould be supervised to ensure that they do not play with the appliance CAUTION The manufacturer do not take the responsibility of the accident happened because the air conditioner is not fixed firmly or installed securely during installing or using the product In case you have difficulty in installation you must ask for an installation specialist help The accident will be hap pened in case of installing improperly Contents PREPARING YOUR AIR CONDITIONER m Safety Precautions 00 eee e E a aea a ae aE aa a eaa EA A PA T EPEA ESEE a UAS 2 m Air Conditioning Unit Main Parts Buttons and Display 4 m Remote Control Buttons a aera aae ae aante a conc ccoo Ee ETT cnn nan enne 5 m Getting Started cuidan cda 6 m Inserting the Remote Control Batteries oooonocinnninnininnnnncnnnccnncnnncnnnrnnnnnnnnnnnn 7 OPERATING YOUR AIR CONDITIONER a Cooling YOU ROOM iecit tete rette eed eset to cde epe 8 E Airing YOUr ROOM iiec abi hang Hd rc ERR ico 9 m Adjusting the Air Flow Direction Horizontally eeen 10 m Adjusting the Air Flow Direction Vertically eee 10 PROGRAMMING YOUR AIR CONDITIONER m Switching the Unit Off Automatically Off Timer seeeee 11 m Canceling the Off Timer esee nnne 11 RECOMMENDATIONS FOR USE m Operating Recommendation sssessssseeeeeeeeeeneen nennen 12 m Temperature and Humidity Ranges
12. r is not correctly triggered Check that the timer has been programmed correctly refer to page 11 Odours are permeated in the Air the room room during air conditioning Technical Specifications Design and specifications are subject to change without notice Model Power Supply XAXA 115V 60Hz XAB 220V 60Hz XKKO 230V 208V 60Hz XD 200 220V 50Hz XXE 220 240V 50Hz The last letter of the Model means the power supply E in the AW07A7SE for instance ENGLISH Method of Installation Before installation be sure to check the installation area for the air conditioner and drain hose Checkpoints prior to installation 1 Check the cabinet and front grille of the unit for any harmful defects such as scratches 2 Be sure to check the power supply Refer to the specifications on the label attached to the unit Installation Conditions 1 As the unit is heavy the wall or window of the installation area should have sufficient strength and durability for operation of the air conditioner and for prevention of any vibration or noise If it is weak reinforcement work should be performed separately 2 It is advisable to install the air conditioner in the north or west side to prevent the effect of direct sunlight When installing it in the south or east side due to unavoidable circumstances it is advisable to install the sunshade to prevent the direct sunlight In this case take care not
13. seem 12 m Cleaning Your Air Conditioner esseseseseeeeeeneeneeeneenen n 13 m Solving Common Problems sse nene 14 m Technical Specifications sessssesseseseeeeeeeenenenneenneennnen nnne 15 METHOD OF INSTALLATION cc cccescceesseccceceescseseccceeeeseneeescsueeseeueeeseseeesesseesesaseeessass 16 ENGLISH Air Conditioning Unit Main Parts Buttons and Display The design and shape are subject to change according to the model 7 EB E Inner air flow blades BE Air outlet right left orientation BE 2 Outer air flow blades Z ZZ up down orientation Z BZ Air inlet Outside Air inlet inside ZY Za Ventilation lever Air filter The air filter is located inside Power plug 4 The type of power plug may differ depending on the local power supply The power plug may be not supplied depending Temperature Timer setting on the model Timer indicator Remote control sensor ue Temperature Temperature indicator adjustment button Fan speed indicators Operating mode indicators RESTART Ak ck COOL FAN Fan speed button COOL FAN Cin Operating mode selection button Air flow blade swing button SWING FAN SPEED MODE ON OFF button Restart Indicator m When the power plug is connected the indicator comes on
14. t the unit from being damaged when it is started immediately after being Plugged in Stopped It will start up automatically after a three minute rest period 2 If the COOL indicator is not lit up on the unit Press the button on the remote control or Press the MODE button on the unit one or more times until the COOL indicator lights up Result 4 The unit beeps each time you press MODE The air conditioner starts up in Cool mode gt You can change modes at any time 3 To adjust the temperature press the O or Qs buttons on the remote control one or more times until the required temperature is displayed To adjust the temperature press the TEMPERATURE button on the unit one or more times until the required temperature is displayed 24 gt 25 gt gt 29 gt 30 gt 18 C gt 19 gt Possible temperatures are between 18 C and 30 C inclusive Result Each time you press the temperature buttons The temperature is adjusted by 1 C and displayed on the control panel The unit beeps The air conditioner starts cooling if the room temperature is higher than the selected temperature 4 To set the fan speed to Then High Press the button on the remote control Low Press the EF button on the remote control FAN SPEED Result Each time you press a button the unit beeps 5 To control the direction of the air flow refer to page 10
15. to cause any hindrance to the flow of outside air 3 When installing the air conditioner be sure to obtain sufficient space on the rear side of the unit for smooth flow of air When operating the air conditioner in closed areas such as inner building with cooling operation and result in trouble with the unit See the illustration below 090 oC Awning Doy o0 o Q9 OoC O O O Oo o Fence wall or other obstacle y a 0000 0000 0 IN v Approx 3 090o 9Uo0 yoo Y Model A XOOOCKXS 180mm XooexJx 220mm XOOOXW K 235mm KKM EK O 150mm min oQ o 7 090o9o0 0 090o9o0 9 0090090 0 0o90090 090o9o090 09 009909 Q Q O OOO v gt If the wall is greater than 150mm thick cut the wall back on a 45 angle if possible 90o9o090 Oo e Jo RADNA 2o0 00o098590o0 70o095906o0 059o0 00609890 00U 000 G 90 00 100mm or more O Ef ENGLISH Installation of the Drain Tube Fix the drain tube as shown in the figure Installation of the Drain Pan The procedure for installing the drain pan should be determined by the condition of the installing area In the case of an area where the drain pan can not be directly installed on the rear side of
16. u must clean it regularly by two weeks to remove the dust on the air filter om Before cleaning your air conditioner ensure that it is switched off and unplugged from the wall socket 1 Open the front grille by pulling on the tabs of the unit gt The removal of the front grille makes it easier to clean the air conditioner After opening the front grille lift it up as much as possible then pull down to release it 2 Grasp the handle on the air filter and lift it slightly and then out to the front 3 Remove all dust on the air filter with a vacuum cleaner or brush 4 When you have finished slide the air filter back into position 5 Clean the outer surfaces with a damp cloth and mild detergent do NOT use benzene solvents or other chemicals Wipe them dry with a clean soft cloth gt Ifyou Then Will not be using the air conditioner for a long period of time Set the fan going for a few hours to dry the inside of the air conditioner thoroughly Switch the air conditioner off and unplug it from the wall socket Clean the filter and outer surfaces Have not used the air conditioner for a long period of time Set the fan going for a few hours to dry the inside of the air conditioner thoroughly ENGLISH Front grille E Front grille v Grille groove Body guide Solving Common Problems Before contacting the after sales service perform the following simple checks They ma
17. y save you the time and expense of an unnecessary service call Problem Explanation Solution The air conditioner does not Check that the circuit breaker used for the air conditioner has not been operate at all triggered Check that the power cable is plugged into a wall socket and the socket is switched on if necessary Check that the operating mode indicator COOL or FAN on the unit is lit up if necessary press On Off on the remote control or unit The air conditioner does not Check that there are no obstacles between you and the unit operate with the remote control Replace the remote control batteries if necessary Check that you are close enough to the unit seven metres yards or less No beep is heard when you press 4 Check that you are pointing the remote control at the remote control b On Off on the remote control sensor on the unit Replace the remote control batteries if necessary The air conditioner does not Check that the correct operating mode has been selected COOL cool The room temperature may be too low Dust may be blocking the air filter refer to page 13 for cleaning instructions Check that there is no obstacle blocking the air flow into or out of the unit The air flow direction does not Check that the air conditioner has been switched on if necessary press change when you press the b On Off on the remote control or unit ES or ADon the unit button The time
Download Pdf Manuals
Related Search