Samsung Monitor LED Samsung Serie 5 15.6" manual do usuário
Contents
1. Before Using the Product Put down the product carefully e The product may fall and break or cause a personal injury Installing the product in an unusual place a place exposed to a lot of fine particles chemical substances or extreme temperatures or an airport or train station where the product should operate continuously for an extended period of time may seriously affect its performance e Besure to consult Samsung Customer Service Center page 70 before installation if you want to install the product at such a place Operation and Safety High voltage runs through the product Do not attempt to disassemble repair or modify the product on your own e An electric shock or fire may result e Contact Samsung Customer Service Center page 70 for repair Before moving the product turn off the power switch and disconnect the power cable and all other connected cables e Otherwise the power cord may be damaged and a fire or electric shock may result If the product generates a strange noise a burning smell or smoke remove the power cord immediately and contact Samsung Customer Service Center page 70 e An electric shock or fire may result Do not let children hang from the product or climb on top of it e The product may fall and your child may become injured or seriously harmed If the product falls or the exterior is damaged p2. Size 15 6 Inches 39 cm Panel Display area 34 423 cm H x 19 354 cm V Horizontal 31 80 kHz Frequency Synchronization Vertical 56 64 Hz Frequency Display Color 262 144 M ti Optimum 1566x768 60Hz Resolution Resolution Maxi RUM 1366x768 60Hz Resolution Maximum Pixel Clock 72 8MHz Analog Power Supply This product uses 100 to 240V Refer to the label at the back of the product as the standard voltage can vary in different countries Signal connectors 15pin to 15pin D sub cable Detachable Without 14 7 x 9 6 x 2 3 Inches Dimensions Wx Stand 37 33 x 24 4 x 5 8 cm H x D Weight 14 7 x 12 8 x 7 0 Inches 2 5 lbs With Stand 37 33 x 32 61 x 17 8 cm 1 15kg Temperature 50 F 104 F 10 C 40 C Operating Environmental Humidity 10 96 80 non condensing considerations Sane Temperature 4 F 113 F 20 C 45 C 9 Humidity 5 Yo 95 non condensing This monitor can be installed and used with any Plug and Play compatible systems Two way data exchange between the monitor Plug and Play and PC system optimizes the monitor settings Monitor installation takes place automatically However you can customize the installation settings if desired Panel Dots Pixels Due to the nature of the manufacturing of this product approximately 1 pixel per million 1pppm may be brighter or darker on the LCD panel This does not affect product perfor
3. WZ The color and shape of parts may differ from what is shown Specifications are subject to change without notice to improve quality To lock an anti theft locking device 1 Fix the cable of your anti theft locking device to a heavy object such as a desk 2 Put one end of the cable through the loop on the other end 3 Insert the locking device into the anti theft lock slot at the back of the product A Lock the locking device e An anti theft locking device can be purchased separately R e _ Refer to the user guide provided with your anti theft locking device for details e Anti theft locking devices can be purchased at electronics retailers or online Connecting and Using a Source Device 2 1 Before Connecting 2 1 1 Pre connection Checkpoints e Before connecting a source device read the user manual provided with it The number and locations of ports on source devices may differ from device to device e _ Do not connect the power cable until all connections are completed Connecting the power cable during connection may damage the product e Check the types of ports at the back of the product you want to connect 2 2 Connecting the Power e _ Connect the power adapter to DC jack on the rear of the product Connect the power cord to the adapter and wall socket The input voltage is switched automatically 2 3 Connecting and Using a Source
4. Before Using the Product dodo g e Br Do not install the product on an unstable or vibrating surface insecure shelf sloped surface etc e The product may fall and break or cause a personal injury e Using the product in an area with excess vibration may damage the product or cause a fire Do not install the product in a vehicle or a place exposed to dust moisture water drips etc oil or smoke e An electric shock or fire may result Do not expose the product to direct sunlight heat or a hot object such as a stove e Otherwise the product lifespan may be reduced or a fire may result Do not install the product within the reach of young children e The product may fall and injure children Edible oil such as soybean oil can damage or deform the product Do not install the product in a kitchen or near a kitchen counter Take care not to drop the product when moving it e Otherwise product failure or personal injury may result Do not set down the product on its front e The screen may become damaged When installing the product on a cabinet or shelf make sure that the bottom edge of the front of the product is not protruding e The product may fall and break or cause a personal injury e Install the product only on cabinets or shelves of the right size
5. T Press MENU on the product 2 Press A YW to move to Picture and press 7 c on the product 3 Press A V to move to Contrast and press 3 c on the product The following screen will appear 4 Adjust the Contrast using the A Y buttons 3 3 Screen Setup Sharpness Make the outline of objects more clear or blurry Range 0 100 A higher value will make the outline of objects clearer A e This menu is not available when MagicBright is in Cinema or Dynamic Contrast mode e This menu is not available when MagicColor is in Full or Intelligent mode e _ This menu is unavailable when Color Effect is set 3 3 1 Configuring Sharpness 7 Press MENU on the product 2 Press A YW to move to Picture and press H C on the product 3 Press A V to move to Sharpness and press 3 c on the product The following screen will appear 4 Adjust the Sharpness using the A W buttons 3 4 Screen Setup MagicBright This menu provides an optimum picture quality suitable for the environment where the product will be used Not available if MagicEco is set to On You can customize the brightness to suit your preferences 3 4 1 Configuring MagicBright Press MENU on the product 2 Press M V to move to Picture and press 3 C on the product 3 Press M V to move to MagicBright and press Q c on the product The following screen will appear PICTURE Custo
6. Use the product at the recommended resolution and frequency e Your eyesight may deteriorate Do not put DC power adapters together e Otherwise a fire may result Remove the plastic bag from the DC power adapter before you use it e Otherwise a fire may result Do not let water enter the DC power adapter or get the adapter wet e An electric shock or fire may result e Avoid using the product outdoors where it can be exposed to rain or snow e Be careful not to get the DC power adapter wet when you wash the floor Do not put the DC power adapter near to any heating apparatus e Otherwise a fire may result Keep the DC power adapter in a well ventilated area Looking at the screen too close for an extended period of time can deteriorate your eyesight Before Using the Product Do not hold the monitor upside down or move it by holding the stand e The product may fall and break or cause a personal injury Do not use humidifiers or stoves around the product e An electric shock or fire may result Rest your eyes for more than 5 minutes for every 1 hour of product use e Eye fatigue will be relieved Do not touch the screen when the product has been turned on for an extended period of time as it will become hot Store the small accessories used with the product out of reach of children Exercise caution when adjusting the product angle
7. 4 7 Configuring Tint Gamma Adjust the mid range brightness Gamma of the picture 4 7 1 Configuring Gamma Press MENU on the product 2 Press M V to move to COLOR and press 73 c on the product o 3 Press A V to move to Gamma and press 9 on the product The following screen will appear 4 Press 4 W to move to the option you want and press oO 5 The selected option will be applied 4 Configuring Tint 44 5 1 Resizing or Relocating the Screen H Position amp V Position H Position Move the screen to the left or right V Position Move the screen up or down 5 1 1 Configuring H Position amp V Position 1 Press MENU on the product 2 Press A V to move to SIZE amp POSITION and press 9 on the product 3 Press 4 W to move to H Position or V Position and press 3 2 The following screen will appear SIZE amp POSITION SIZE amp POSITION 4 Press A V to configure H Position or V Position 5 Resizing or Relocating the Screen KI 5 2 Resizing or Relocating the Screen Image Size Change the picture size 5 2 1 Changing the Image Size Press MENU on the product 2 Press A W to move to SIZE amp POSITION and press H m on the product 3 Press A V to move to Image Size and press 3 on the product The following screen will appear SIZE amp POSITION e Auto Display the picture according to the aspect ratio of the input source e Wi
8. SAMSUNG 0800 726 786 http Awww samsung com SPAIN 902 1 SAMSUNG 902 172 678 http www samsung com SWEDEN 0771 726 7864 SAMSUNG http www samsung com Appendix Appendix EUROPE SWITZERLAND 0848 SAMSUNG http www samsung com ch 7267864 CHF 0 08 min German http www samsung com ch_fr French U K 0330 SAMSUNG 7267864 http www samsung com CIS ARMENIA 0 800 05 555 http www samsung com AZERBAIJAN 088 55 55 555 http www samsung com BELARUS 810 800 500 55 500 http www samsung com GEORGIA 0 800 555 555 http www samsung com KAZAKHSTAN 8 10 800 500 55 500 http www samsung com GSM 7799 KYRGYZSTAN 00 800 500 55 500 http www samsung com MOLDOVA 0 800 614 40 http www samsung com MONGOLIA 7 800 555 55 55 http www samsung com RUSSIA 8 800 555 55 55 http www samsung com TADJIKISTAN 8 10 800 500 55 500 http www samsung com UKRAINE 0 800 502 000 http www samsung com ua Ukrainian http www samsung com ua_ru Russian UZBEKISTAN 8 10 800 500 55 500 http www samsung com ASIA PACIFIC AUSTRALIA 1300 362 603 http www samsung com CHINA 400 810 5858 http www samsung com HONG KONG 852 3698 4698 http www samsung com hk Chinese http www samsung com hk_en English INDIA 1800 1100 11 http www samsung com 3030 8282 1800 3000 8282 1800 266 8282 Appendix
9. This marking on the product accessories or literature indicates that the product and its electronic accessories e g charger headset USB cable should not be disposed of with other household waste at the end of their working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take these items for environmentally safe recycling Business users should contact their supplier and check the terms and conditions of the purchase contract This product and its electronic accessories should not be mixed with other commercial wastes for disposal Appendix Terminology OSD On Screen Display On screen display OSD allows you to configure on screen settings to optimize the picture quality as required It allows you to change the screen brightness tint size and many other settings using menus displayed on the screen Gamma The Gamma menu adjusts the grey scale that represents middle tones on the screen Adjusting the brightness brightens the whole screen but adjusting Gamma only brightens the medium brightness Grey scale Scale refers to levels of color intensity that show variations of col
10. 64 Q amp A SPECIFICATIONS 66 General 68 PowerSaver 69 Standard Signal Mode Table APPENDIX 70 Contact SAMSUNG WORLD WIDE 76 Responsibility for the Pay Service Cost to Customers 76 Not a product defect 76 A Product damage caused by customer s fault 76 Others 77 Correct Disposal of This Product Waste Electrical amp Electronic Equipment 78 Terminology INDEX Before Using the Product Copyright The contents of this manual are subject to change without notice to improve quality 2012 Samsung Electronics Samsung Electronics owns the copyright for this manual Use or reproduction of this manual in parts or entirety without the authorization of Samsung Electronics is prohibited Microsoft Windows and Windows NT are registered trademarks of Microsoft Corporation VESA DPM and DDC are registered trademarks of the Video Electronics Standards Association e An administration fee may be charged if either o a an engineer is called out at your request and there is no defect in the product i e where you have failed to read this user manual o b you bring the unit to a repair center and there is no defect in the product i e where you have failed to read this user manual e The amount of such administration charge will be advised to you before any work or home visit is carried out Icons used in this manual The following images are for reference only Real life situations may differ fro
11. Display gt Settings and adjust the resolution Windows Vista Go to Control Panel gt Appearance and Personalization Personalize Display Settings and adjust the resolution Windows 7 Go to Control Panel Appearance and Personalization Display Adjust Resolution and adjust the resolution Windows 8 Go to Settings Control Panel gt Appearance and Personalization Display Adjust Resolution and adjust the resolution How do set power saving mode Windows XP Set power saving mode in Control Panel gt Appearance and Themes Display Screen Saver Settings or BIOS SETUP on the PC Windows ME 2000 Set power saving mode in Control Panel Display Screen Saver Settings or BIOS SETUP on the PC Windows Vista Set power saving mode in Control Panel Appearance and Personalization Personalize Screen Saver Settings or BIOS SETUP on the PC Windows 7 Set power saving mode in Control Panel gt Appearance and Personalization Personalize Screen Saver Settings or BIOS SETUP on the PC Windows 8 Set power saving mode in Settings Control Panel Appearance and Personalization Personalize gt Screen Saver Settings or BIOS SETUP on the PC Refer to the user manual for your PC or graphics card for further instructions on adjustment 9 Troubleshooting Guide 65 v Specifications 10 1 General Model Name S16B110N
12. Installing the Software Magic Tune 8 1 1 What is MagicTune Mag clune MagicTune is a software program that helps with monitor adjustments by providing comprehensive descriptions of monitor functions and easy to understand guidelines You can adjust the product with the mouse and the keyboard without using the operating buttons of the product 8 1 2 Installing the Software 7 Insert the installation CD into the CD ROM drive 2 Select the MagicTune setup program NG If the pop up screen for the software installation does not appear on the main screen find and double click the MagicTune setup file on the CD ROM 3 Select the installation language and click Next 4 Complete the remaining software installation steps according to the instructions displayed on the screen 4 e The software may not work properly if you do not restart the computer after the installation a e The MagicTune icon may not appear depending on the computer system and the product specifications e Ifthe shortcut icon does not appear press the F5 key Restrictions and Problems with the Installation MagicTune The installation of MagicTune may be affected by the graphics card motherboard and the networking environment System Requirements OS e Windows XP Windows Vista Windows 7 Windows 8 Installing the Software 8 1 3 Removing the Software You can only remove MagicTune through Add or Remove Programs in Window
13. AFRICA ANGOLA 91 726 7864 http www samsung com BOTSWANA 0800 726 000 http www samsung com CAMEROON 7095 0077 http www samsung com COTE D IVOIRE 8000 0077 http www samsung com GHANA 0800 10077 http www samsung com 0302 200077 KENYA 0800 724 000 http www samsung com NAMIBIA 8197267864 http www samsung com NIGERIA 0800 726 7864 http www samsung com SENEGAL 800 00 0077 http www samsung com SOUTH AFRICA 0860 SAMSUNG 726 7864 http www samsung com TANZANIA 0685 88 99 00 http www samsung com UGANDA 0800 300 300 http www samsung com ZAMBIA 211350370 http www samsung com Appendix Appendix Responsibility for the Pay Service Cost to Customers NG When the service is requested in spite of in warranty we may charge you for a visit from a service technician in the following cases Not a product defect Cleaning of the product Adjustment Explanation Re installation and etc fa service technician gives instructions on how to use product or simply adjusts options without disassembling product Ifa defect is caused by external environmental factors Internet Antenna Wired Signal etc e Ifa product is reinstalled or devices are connected additionally after installing the purchased product for the first time e Ifa product is reinstalled to move to a different spot or to move to a different house e If customer requests instructions on how to use because of another com
14. Appendix ASIA PACIFIC INDONESIA 0800 112 8888 http www samsung com 021 5699 7777 JAPAN 0120 327 527 http www samsung com MALAYSIA 1800 88 9999 http www samsung com NEW ZEALAND 0800 SAMSUNG 0800 726 786 http www samsung com PHILIPPINES 1 800 10 SAMSUNG 726 7864 http www samsung com for PLDT 1 800 3 SAMSUNG 726 7864 for Digitel 1 800 8 SAMSUNG 726 7864 for Globe 02 5805777 SINGAPORE 1800 SAMSUNG 726 7864 http www samsung com TAIWAN 0800 329 999 http www samsung com 0266 026 066 THAILAND 1800 29 3232 http www samsung com 02 689 3232 VIETNAM 1 800 588 889 http www samsung com MIDDIE EAST BAHRAIN 8000 4726 http www samsung com ae English http www samsung com ae_ar Arabic EGYPT 08000 726786 http www samsung com IRAN 021 8255 http www samsung com JORDAN 800 22273 http www samsung com 065777444 KUWAIT 183 2255 http www samsung com ae English http www samsung com ae_ar Arabic MOROCCO 080 100 2255 http www samsung com Appendix Appendix MIDDIE EAST OMAN 800 SAMSUNG 726 7864 http www samsung com ae English http www samsung com ae_ar Arabic SAUDI ARABIA 9200 21230 http www samsung com ae English http www samsung com ae_ar Arabic TURKEY 444 77 11 http www samsung com U A E 800 SAMSUNG 726 7864 http www samsung com
15. Device Connecting and Using a PC 2 3 1 Connecting to a PC Select a connection method suitable for your PC K Connecting parts may differ in different products Connection Using the D SUB Cable Analogue Type K Do not connect the power cable before connecting all other cables Ensure you connect a source device first before connecting the power cable 1 Connect the D SUB cable to the RGB IN port on the back of the product and the RGB port on the PC 2 Connect the DC power adapter to the product and a power socket Next turn on the power switch on the PC For details refer to 2 2 Connecting the Power Connecting and Using a Source Device 2 3 2 Driver Installation K e You can set the optimum resolution and frequency for this product by installing the corresponding drivers e An installation driver is contained on the CD supplied with the product e _ Ifthe file provided is faulty visit the Samsung homepage http www samsung com and download the file Insert the user manual CD provided with the product into the CD ROM drive Click Windows Driver Follow the instructions given on the screen to proceed with installation A UNa Select your product model from the list of models Select the display adapter on which you ward to intall the monitor Select the monitor which you war to install 5 Go to Display Properties and check that the resolution and refresh rate are appropriate Refer to you
16. e Contact the dealer from whom you purchased the product if any item is missing e The appearance of the components and items sold separately may differ from the image shown Components gt gr Warranty card Quick setup guide y User manual Not available in some locations aS Power cable DC power adapter D SUB cable optional Stand Stand Connector K Components may vary depending on the country 1 Preparations 18 Preparations 1 2 Parts 1 2 1 Frontal Buttons WZ The color and shape of parts may differ from what is shown Specifications are subject to change without notice to improve quality SAMSUNG MENU CG V A Q oe AUTO Gb o This is a touch type button Tap the button lightly with a finger 5 Icons Description e Open or close the onscreen display OSD menu or return to the parent menu e OSD control lock Maintain the current settings or lock the OSD control to prevent unintended changes to settings Enable To lock the OSD control press the MENU button for 10 seconds Disable To unlock the locked OSD control press the MENU button for more than 10 seconds MENU NG If the OSD control is locked e Brightness and Contrast MagicBright can be adjusted and INFORMATION can be viewed e The Customized Key function can be used by pressing the Qp button The Customized Key function specified before the OSD control was locked is available even when t
17. electric shock or fire may result Remove foreign substances such as dust around the plug pins and power socket with a dry cloth e Otherwise a fire may result Before Using the Product A Caution Ig NG Do not unplug the power cord when the product is in use e The product may become damaged by an electric shock Do not use the power cord for products other than authorized products supplied by Samsung An electric shock or fire may result Keep the power socket where the power cord is connected unobstructed e If any problem occurs in the product unplug the power cable to completely cut the power to the product Power to the product cannot be completely cut off with the power button Hold the plug when disconnecting the power cord from the power socket e An electric shock or fire may result Installation and Safety A Warning DO NOT PLACE CANDLES INSECT REPELLANTS OR CIGARETTES ON TOP OF THE PRODUCT DO NOT INSTALL THE PRODUCT NEAR HEAT SOURCES e Otherwise a fire may result Avoid installing the product in a narrow space with bad ventilation such as a bookshelf or wall closet e Otherwise a fire may result due to an increased internal temperature Keep the plastic packaging bag for the product in a place that cannot be reached by children e Children may suffocate
18. is heard when my PC is booting If a beeping sound is heard when your PC is booting have your PC serviced 9 Troubleshooting Guide 63 9 2 Troubleshooting Guide Q amp A Question How can I change the frequency Answer Set the frequency on your graphics card Windows XP Go to Control Panel gt Appearance and Themes Display Settings Advanced Monitor and adjust Refresh rate under Monitor settings Windows ME 2000 Go to Control Panel gt Display gt Settings Advanced Monitor and adjust Refresh rate under Monitor settings Windows Vista Go to Control Panel gt Appearance and Personalization Personalization Display Settings Advanced Settings Monitor and adjust Refresh rate under Monitor settings Windows 7 Go to Control Panel Appearance and Personalization Display gt Screen Resolution gt Advanced settings Monitor and adjust Refresh rate under Monitor settings Windows 8 Go to Settings Control Panel gt Appearance and Personalization gt Display gt Screen Resolution Advanced settings Monitor and adjust Refresh rate under Monitor settings 9 Troubleshooting Guide 7 Troubleshooting Guide Question Answer How can change the resolution Windows XP Go to Control Panel gt Appearance and Themes Display Settings and adjust the resolution Windows ME 2000 Go to Control Panel gt
19. of space as shown below or greater when installing the product A The exterior may differ depending on the product SANA AE 4 gt inches 10 cm SAMSUNG a 3 93 inches 10 cm Precautions for storage A Be sure to contact Samsung Customer Service Center page 70 if the inside of the monitor needs cleaning Service fee will be charged Before Using the Product Safety Precautions Electricity and Safety NG The following images are for reference only Real life situations may differ from what is shown in the images A Warning Do not use a damaged power cord or plug or a loose power socket e An electric shock or fire may result Do not plug many products into the same power socket e Otherwise the socket may overheat and cause a fire N Do not touch the power plug with wet hands M G EN e Otherwise an electric shock may result Insert the power plug all the way in so it is not loose on e An unstable connection may cause a fire Ensure you connect the power plug to a grounded power socket type 1 g insulated devices only e An electric shock or injury may result Do not bend or pull the power cord with force Do not weigh the power cord 4 o down with a heavy object e Adam wer cord m an electric shock or fire damaged power cord may cause Do not place the power cord or product near heat sources e An
20. or stand height e Otherwise children s fingers or hands may become stuck and injured e Tilting the product excessively may cause it to fall and result in personal injury Do not place heavy objects on the product e Product failure or personal injure may result Before Using the Product Correct posture to use the product Use the product in the correct posture as follows e Straighten your back e Allow adistance of 45 to 50cm between your eye and the screen and look slightly downward at the screen Keep your eyes directly in front of the screen e Adjust the angle so light does not reflect on the screen e _ Keep your forearms perpendicular to your upper arms and level with the back of your hands e Keep your elbows at about a right angle e Adjust the height of the product so you can keep your knees bent at 90 degrees or more your heels attached to the floor and your arms lower than your heart 1 1 Preparations Checking the Contents 1 1 1 Removing the Packaging 1 Open the packaging box Be careful not to damage the product when you open the packaging with a sharp instrument 7 Remove the styrofoam from the product Check the components and remove the styrofoam and plastic bag NG This image is for reference only Store the box in a dry area so that it can be used when moving the product in the future Preparations 1 1 2 Checking the Components K
21. 47 712 59 790 85 500 4 4 Horizontal Frequency R The time required to scan a single line from the left to the right side of the screen is called a horizontal cycle The reciprocal number of a horizontal cycle is called horizontal frequency Horizontal frequency is measured in kHz e Vertical Frequency Repeating the same picture dozens of times per second allows you to view natural pictures The repeat frequency is called vertical frequency or refresh rate and is indicated in Hz 10 Specifications 69 Appendix Contact SAMSUNG WORLD WIDE A If you have any questions or comments relating to Samsung products please contact the SAMSUNG customer care center NORTH AMERICA U S A 1 800 SAMSUNG 726 7864 http www samsung com CANADA 1 800 SAMSUNG 726 7864 http www samsung com ca English http www samsung com ca_fr French MEXICO 01 800 SAMSUNG 726 7864 http www samsung com LATIN AMERICA ARGENTINE 0800 333 3733 http www samsung com BOLIVIA 800 10 7260 http www samsung com BRAZIL 0800 124 421 http www samsung com 4004 0000 CHILE 800 SAMSUNG 726 7864 http www samsung com From mobile 02 482 82 00 COLOMBIA 01 8000112112 http www samsung com COSTA RICA 0 800 507 7267 http www samsung com latin Spanish http www samsung com latin_en English DOMINICA 1 800 751 2676 http www samsung com latin Spanish http www samsu
22. 7 Power off both the PC and product 2 Disconnect the cables from the product 3 Power on the product 4 If the message Check Signal Cable appears the product is working normally NG If the screen remains blank check the PC system video controller and cable 9 1 2 Checking the Resolution and Frequency For a mode that exceeds the supported resolution refer to 10 3 Standard Signal Mode Table the message Not Optimum Mode will appear for a short time 9 1 3 Check the following Installation issue PC mode The screen keeps switching on and off Check the cable connection between the product and PC and ensure the connectors are locked Refer to 2 3 Connecting and Using a PC Screen issue The power LED is off The screen will not switch Check that the power cable is connected on properly Refer to 2 3 Connecting and Using a PC The message Check Signal Cable appears Check that the cable is properly connected to the product Refer to 2 3 Connecting and Using a PC Check that the device connected to the product is powered on Troubleshooting Guide Screen issue Not Optimum Mode is displayed This message appears if the signal from the graphics card exceeds the maximum resolution or frequency for the product Change the maximum resolution and frequency to suit the product performance referring to Standard Signal Mode Table page 69 The image
23. M V to move to the option you want and press 5 0 5 The selected option will be applied 6 Setup and Reset 50 6 4 Setup and Reset Off Timer On Off You can set the product to automatically turn off 6 4 1 Configuring Off Timer On Off 1 2 Press MENU on the product Press A V to move to SETUP amp RESET and press 4 C3 on the product Press A V to move to Off Timer On Off and press H C on the product The following screen will appear SETUP amp RESET e Off Deactivate the off timer so that the product does not power off automatically e On Activate the off timer so that the product powers off automatically Press A W to move to the option you want and press T T The selected option will be applied 6 Setup and Reset 51 6 5 Setup and Reset Off Timer Setting The off timer can be set within a range of 1 to 23 hours The product will automatically power off after the specified number of hours A This menu is available only when Off Timer On Off is set to On 6 5 1 Configuring Off Timer Setting Press MENU on the product 2 Press A W to move to SETUP amp RESET and press I on the product 3 Press A V to move to Off Timer Setting and press 9 on the product The following screen will appear SETUP amp RESET 4 Press A V to configure Off Timer Setting 6 Setup and Reset 52 Setup and Reset 6 6 Key Repeat Time Control the response rate of a but
24. O Off Timer OnOff 51 Off Timer Setting 52 Parts 19 Q amp A64 R Red 39 Requirements Before Contacting Samsung Customer Service Center 62 Reset 48 Responsibility for the Pay Service Cost to Customers 76 Index S Safety Precautions 9 Sharpness 34 Standard Signal Mode Table 69
25. The color and the appearance may differ depending on the product and the specifications are subject to change without prior notice to improve the performance BN46 00223A 04 Table Of Contents BEFORE USING THE PRODUCT PREPARATIONS CONNECTING AND USING A SOURCE DEVICE Oo ea ea SI OS D oO O ENG SEN VIS O 17 ir 18 19 21 22 22 23 23 24 24 25 25 26 ar 28 Copyright Icons used in this manual Symbols for safety precautions Cleaning Cleaning Securing the Installation Space Precautions for storage Safety Precautions Electricity and Safety Installation and Safety Operation and Safety Correct posture to use the product Checking the Contents Removing the Packaging Checking the Components Parts Frontal Buttons Reverse Side Installation Attaching the Stand Adjusting the Product Tilt Anti theft Lock Before Connecting Pre connection Checkpoints Connecting the Power Connecting and Using a PC Connecting to aPC Driver Installation Setting Optimum Resolution Changing the Resolution Using a PC Table Of Contents SCREEN SETUP 3 32 33 33 34 34 35 35 36 36 37 37 CONFIGURING TINT 38 38 39 39 40 40 41 41 42 42 43 43 44 44 Brightness Configuring Brightness Contrast Configuring Contrast Sharpness Configuring Sharpness MagicBright Configuring MagicBright Coarse Adjusting Coarse Fine Adjusting Fi
26. after the installation e The MultiScreen icon may not appear depending on the computer system and the product specifications e Ifthe shortcut icon does not appear press the F5 key Restrictions and Problems with the Installation MultiScreen The MultiScreen installation may be affected by the Graphics card Motherboard and the Networking environment Operating System oS e Windows 2000 e Windows XP Home Edition e Windows XP Professional e Windows Vista 32bit e Windows 7 32bit e Windows 8 32bit NG For MultiScreen the operating systems Windows 2000 or later is recommended Hardware e Atleast 32MB of memory e Atleast 60MB of free space on the hard disk drive Installing the Software 8 2 2 Removing the Software Click Start select Settings Control Panel and then double click Add or Remove Programs Select MultiScreen from the program list and click the Add Delete button 9 1 Troubleshooting Guide Requirements Before Contacting Samsung Customer Service Center 9 1 1 Testing the Product W4 Before calling Samsung Customer Service Center test your product as follows If the problem persists contact Samsung Customer Service Center Check if your product is operating normally by using the product test function If the screen is turned off and the power indicator blinks even though the product is properly connected to a PC perform a self diagnosis test
27. d by those horizontal lines A vertical frequency of 60 means that an image is transmitted 60 times per second The vertical frequency is also called refresh rate and affects screen flicker Appendix Appendix Resolution Resolution is the number of horizontal pixels and vertical pixels that form a screen It represents the level of display detail A higher resolution displays a greater amount of information on the screen and is suitable for performing multiple tasks at the same time E g A resolution of 1920 x 1080 consists of 1 920 horizontal pixels horizontal frequency and 1 080 vertical lines vertical resolution Plug amp Play The Plug amp Play feature allows the automatic exchange of information between a monitor and PC to produce an optimum display environment The monitor uses VESA DDC international standard to execute Plug amp Play Index A Appendix 70 B Before Connecting 24 Blue 41 Brightness 32 C Checking the Contents 17 Cleaning 7 Coarse 36 Color Effect 43 Color Tone 42 Connecting and Using a PC 25 Contact 70 Contact SAMSUNG WORLD WIDE 70 Contrast 33 Copyright 6 Correct posture to use the product 16 Customized Key 54 D Display Time 55 F Fine 37 G Gamma 44 General 66 Green 40 Image Size 46 INFORMATION 57 Installation 22 K Key Repeat Time 53 L Language 49 M MagicBright 35 MagicColor 38 MagicEco 50 Menu Transparency 56 MultiScreen 60
28. de Display the picture in full screen regardless of the aspect ratio of the input source 4 Press A V to move to the option you want and press 37 3 5 The selected option will be applied 5 Resizing or Relocating the Screen KI 5 3 Resizing or Relocating the Screen Menu H Position amp Menu V Position Menu H Position Move the menu position to the left or right Menu V Position Move the menu position up or down 5 3 1 Configuring Menu H Position amp Menu V Position 7 Press MENU on the product 2 Press A V to move to SIZE amp POSITION and press 9 on the product 3 Press 4 W to move to Menu H Position or Menu V Position and press 9 2 The following screen will appear SIZE amp POSITION SIZE amp POSITION 4 Press A V to configure Menu H Position or Menu V Position 5 Resizing or Relocating the Screen Setup and Reset 6 1 Reset Return all the settings for the product to the default factory settings 6 1 1 Initializing Settings Reset Press MENU on the product 2 Press A V to move to SETUP amp RESET and press t c on the product 3 Press A V to move to Reset and press 9 on the product The following screen will appear SETUP amp RESET 4 Press M V to move to the option you want and press 5 0 5 The selected option will be applied 6 Setup and Reset 48 6 2 Setup and Reset Language Set the menu language K e Achange to the language settin
29. disappear 6 8 1 Configuring Display Time 7 Press MENU on the product 2 Press A W to move to SETUP amp RESET and press t c on the product 3 Press A V to move to Display Time and press 3 c on the product The following screen will appear SETUP amp RESET 15 sec 10 sec 20 sec 200 sec 4 Press M V to move to the option you want and press 5 0 5 The selected option will be applied 6 Setup and Reset 55 6 9 Setup and Reset Menu Transparency Set the transparency for the menu windows 6 9 1 Changing Menu Transparency Press MENU on the product 2 Press A V to move to SETUP amp RESET and press t c on the product 3 Press A V to move to Menu Transparency and press 3 on the product The following screen will appear SETUP amp RESET 4 Press 4 W to move to the option you want and press 5 0 5 The selected option will be applied 6 Setup and Reset 56 INFORMATION Menu and Others 7 1 INFORMATION View the current input source frequency and resolution 7 1 1 Displaying INFORMATION T Press MENU on the product 2 Press 4 W to move to INFORMATION The current input source frequency and resolution will appear PICTURE y COLOR HI SIZE amp POSITION kHz Hz PP SETUP amp RESET INFORMATION gt fili Y BE 4 A The displayed menu items may vary depending on the model 7 INFORMATION Menu and Others 8 1
30. en will appear 4 Adjust the Red using the A W buttons 4 Configuring Tint ET 4 3 Configuring Tint Green Adjust the value of the color green in the picture Range 0 100 A higher value will increase the intensity of the color EZ gt This menu is not available when MagicColor is in Full or Intelligent mode e This menu is unavailable when Color Effect is set 4 3 1 Configuring Green Press MENU on the product 2 Press A W to move to COLOR and press 9 2 on the product 3 Press 4 W to move to Green and press 3 C on the product The following screen will appear 4 Adjust the Green using the A W buttons 4 Configuring Tint 40 4 4 Configuring Tint Blue Adjust the value of the color blue in the picture Range O 100 A higher value will increase the intensity of the color Wg This menu is not available when MagicColor is in Full or Intelligent mode e _ This menu is unavailable when Color Effect is set 4 4 1 Configuring Blue Press MENU on the product 2 Press A W to move to COLOR and press 9 2 on the product 3 Press A V to move to Blue and press 3 on the product The following screen will appear 4 Adjust the Blue using the A V buttons 4 Configuring Tint 4 4 5 Configuring Tint Color Tone Adjust the general color tone of the picture EZ gt This menu is not available when MagicColor is in Full or Intel
31. g will only be applied to the onscreen menu display e It will not be applied to other functions on your PC 6 2 1 Changing the Language 1 Press MENU on the product 2 Press A W to move to SETUP amp RESET and press t c on the product 3 Press A V to move to Language and press 3 C on the product The following screen will appear SETUP amp RESET English Deutsch Espa ol Fran ais Italiano Svenska Pycckui Portugues Turkce Polski Magyar 4 Press A V to move to the language you want and press I 5 The selected option will be applied 6 Setup and Reset 49 6 3 Setup and Reset MagicEco This function provides user a low power mode which is realized by lowering the current of the display panel A This menu is not available when MagicBright is in Dynamic Contrast mode 6 3 1 Configuring MagicEco 7 Press MENU on the product 2 Press A W to move to SETUP amp RESET and press t c on the product 3 Press A V to move to MagicEco and press 7 3 on the product The following screen will appear SETUP amp RESET Power Saving Off e 100 When 100 is selected the power consumption is 100 of default setting e 75 When 75 is selected the power consumption is about 75 of default setting e 50 When 50 is selected the power consumption is about 50 of default setting e Power Saving Off When Power Saving Off is selected the function is turned Off 4 Press
32. he OSD control is locked Configure Customized Key and press 4 The following options will be enabled MagicBright MagicEco Image Size Gi g g 9 9 14 To configure Customized Key go to SETUP amp RESET Customized Key and select the mode you want Move to the upper or lower menu or adjust the value for an option on the AN OSD menu o Adjust the screen brightness 1 Preparations ETE Preparations Icons Description oe Confirm a menu selection Press the AUTO button to automatically adjust the screen settings AUTO K Changing the resolution in Display Properties will activate the Auto Adjustment function amp Tum the screen on or off The power indicator will be lit when the product is operating normally SS Power lamp K To reduce power consumption it is best to remove the power cable when you will not be using the product for an extended period of time Preparations 1 2 2 Reverse Side NG The color and shape of parts may differ from what is shown Specifications are subject to change without notice to improve quality Port Ports Connect to the DC power adapter Te Connect to aPC using the D SUB cable Preparations 1 3 Installation 1 3 1 Attaching the Stand NG Before assembling the product place the product down on a flat and
33. ight is set to Cinema or Dynamic Contrast mode MagicColor MagicColor is a new picture quality improvement technology developed independently by Samsung which delivers vivid natural colors without picture quality degradation A This menu is unavailable when Color Effect is set 4 1 1 Configuring MagicColor Press MENU on the product 2 Press M V to move to COLOR and press H C on the product 3 Press A V to move to MagicColor and press m c on the product The following screen will appear WG Demo Full ti Intelligent e Off Disable MagicColor e Demo Compare normal screen mode with MagicColor mode e Full Obtain a vivid picture quality for all areas including the flesh colors in the picture e Intelligent Improve the chroma for all areas except the flesh colors in the picture 4 Press A V to move to the option you want and press 5 0 5 The selected option will be applied 4 Configuring Tint ET 4 2 Configuring Tint Red Adjust the value of the color red in the picture Range 0 100 A higher value will increase the intensity of the color EZ gt This menu is not available when MagicColor is in Full or Intelligent mode a A e This menu is unavailable when Color Effect is set 4 21 Configuring Red 7 Press MENU on the product 2 Press A W to move to COLOR and press 9 2 on the product 3 Press A V to move to Red and press 3 c on the product The following scre
34. ligent mode e This menu is unavailable when Color Effect is set 4 5 1 Configuring the Color Tone Settings Press MENU on the product 2 Press M V to move to COLOR and press H C on the product 3 Press A V to move to Color Tone and press t c on the product The following screen will appear Cook Normal Warm Custom e Cool Sets the color temperature of the screen to a cooler color e Normal Sets the color temperature of the screen to the standard color temperature e Warm Sets the color temperature of the screen to a warmer color e Custom Select this menu to set the color temperature manually If you do not like the preset color temperatures you can manually adjust the value of RGB 4 Press A V to move to the option you want and press 13 8 5 The selected option will be applied 4 Configuring Tint 42 4 6 Configuring Tint Color Effect You can change the overall atmosphere by changing the color of pictures IZ This menu is unavailable when MagicColor is set i 4 6 1 Configuring Color Effect 1 Press MENU on the product 2 Press A V to move to COLOR and press 9 2 on the product 3 Press A V to move to Color Effect and press 3 8 on the product The following screen will appear Off Grayscale Green Aqua Sepia 4 4 Press M V to move to the option you want and press a 5 The selected option will be applied 4 Configuring Tint 43
35. m Standard Game Cinema Dynamic Contrast Custom Customize the contrast and brightness as required Standard Obtain a picture quality suitable for editing documents or using Internet Game Obtain a picture quality suitable for playing games that involve many graphic effects and dynamic movements Cinema Obtain the brightness and sharpness of TVs suitable for enjoying video and DVD content Dynamic Contrast Obtain balanced brightness through automatic contrast adjustment 4 Press 4 W to move to the option you want and press a c 5 The selected option will be applied 3 5 Screen Setup Coarse Adjust the screen frequency 3 5 1 Adjusting Coarse Press MENU on the product 2 Press M V to move to Picture and press 3 Press M V to move to Coarse and press appear oO Q C2 on the product ce on the product The following screen will 4 Adjust the Coarse using the A W buttons 3 Screen Setup EI 3 6 Screen Setup Fine Fine adjust the screen to obtain a vivid picture 3 6 1 Adjusting Fine Press MENU on the product 2 Press 4 W to move to Picture and press 3 C on the product 3 Press A W to move to Fine and press 13 c on the product The following screen will appear 4 Adjust the Fine using the A W buttons 3 Screen Setup 4 1 Configuring Tint Adjust the tint of the screen This menu is not available when MagicBr
36. m what is shown in the images Symbols for safety precautions A Warning A serious or fatal injury may result if instructions are not followed Personal injury or damage to properties may result if instructions are A Caution not followed S Activities marked by this symbol are prohibited Q Instructions marked by this symbol must be followed Before Using the Product Cleaning Cleaning Exercise care when cleaning as the panel and exterior of advanced LCDs are easily scratched Take the following steps when cleaning 1 Power off the monitor and computer 2 Disconnect the power cord from the monitor 14 Hold the power cable by the plug and do not touch the cable with wet hands Otherwise an electric shock may result 3 Wipe the monitor screen using a clean soft and dry cloth e Donot apply a cleaning agent that contains alcohol solvent or surfactant to the monitor e Do not spray water or detergent directly on the product 4 Wet a soft and dry cloth in water and wring thoroughly to clean the exterior of the monitor 5 Connect the power cord to the product after cleaning the product 6 Power on the monitor and computer Before Using the Product Securing the Installation Space e Ensure some space around the product for ventilation An internal temperature rise may cause fire and damage the product Be sure to allow the amount
37. mance WZ The above specifications are subject to change without notice to improve quality 10 Specifications 66 v Specifications K This device is a Class B digital apparatus USA only Dispose unwanted electronics through an approved recycler To find the nearest recycling location go to our website www samsung com recyclingdirect or call 877 278 0799 v Specifications 10 2 PowerSaver The power saving function of this product reduces power consumption by switching off the screen and changing the color of the power LED if the product is not used for a specified period of time The power is not turned off in power saving mode To switch the screen back on press any key on the keyboard or move the mouse Power saving mode functions only when the product is connected to a PC that has a power saving function PowerSaver Normal operation Power saving mode Power off N e changed mode Power button Power Indicator On Blinking Off Less than Less than Power Consumption 8 watts 0 4 watts 0 4 watts The power consumption level can vary in different operating conditions or when settings are e To reduce the power consumption to O watts turn off the power switch on the back of the product or disconnect the power cable Be sure to disconnect the power cable when you will not be using the product for an extended period of time To reduce the power consumptio
38. n to O watts when the power switch is not available disconnect the power cable 10 Specifications 68 y Specifications 10 3 Standard Signal Mode Table This product can be set to only one resolution for each screen size to obtain the optimum picture quality due to the nature of the panel Therefore a resolution other than the specified resolution may degrade the picture quality To avoid this it is recommended that you select the optimum resolution specified for the screen size of your product N e e _ Check the frequency when you exchange a CDT monitor connected to a PC for an LCD monitor If the LCD monitor does not support 85Hz change the vertical frequency to 60Hz using the CDT monitor before you exchange it with the LCD monitor If a signal that belongs to the following standard signal modes is transmitted from your PC the screen will automatically be adjusted If the signal transmitted from the PC does not belong to the standard signal modes the screen may be blank even though the power LED turns on In such a case change the settings according to the following table by referring to the graphics card user manual neuen mama enca puaicieck Sin Poy KHz Hz Mad laag VESA 640 x 480 31 469 59 940 25 175 J VESA 800 x 600 35 156 56 250 36 000 1 4 VESA 800 x 600 37 879 60 317 40 000 4 4 VESA 1024 x 768 48 363 60 004 65 000 FI VESA 1280 x 720 45 000 60 000 74 250 VESA 1366 x 768
39. nd line Appendix Appendix EUROPE CZECH 800 SAMSUNG 800 726786 http www samsung com Samsung Electronics Czech and Slovak s r o Oasis Florenc Sokolovska 394 17 180 00 Praha 8 DENMARK 70 7019 70 http www samsung com EIRE 0818 717100 http www samsung com ESTONIA 800 7267 http www samsung com FINLAND 09 85635050 http www samsung com FRANCE 01 48 63 00 00 http www samsung com GERMANY 0180 5 SAMSUNG bzw http www samsung com 0180 5 7267864 0 14 Min aus dem dt Festnetz aus dem Mobilfunk max 0 42 Min GREECE 80111 SAMSUNG 80111 726 http www samsung com 7864 only from land line 30 210 6897691 from mobile and land line HUNGARY 06 80 SAMSUNG 726 7864 http www samsung com ITALIA 800 SAMSUNG 726 7864 http www samsung com LATVIA 8000 7267 http www samsung com LITHUANIA 8 800 77777 http www samsung com LUXEMBURG 261 03 710 http www samsung com MONTENEGRO 020 405 888 http www samsung com NETHERLANDS 0900 SAMSUNG http www samsung com 0900 7267864 0 10 Min NORWAY 815 56480 http www samsung com POLAND 0 801 1SAMSUNG 172 678 http www samsung com 48 22 607 93 33 PORTUGAL 808 20 SAMSUNG 808 20 7267 http www samsung com ROMANIA 08008 SAMSUNG 08008 726 http www samsung com 7864 TOLL FREE No SERBIA 0700 Samsung 0700 726 7864 http www samsung com SLOVAKIA 0800
40. ne MagicColor Configuring MagicColor Red Configuring Red Green Configuring Green Blue Configuring Blue Color Tone Configuring the Color Tone Settings Color Effect Configuring Color Effect Gamma Configuring Gamma Table Of Contents RESIZING OR 45 RELOCATING THE SCREEN 46 SETUP AND RESET 48 48 49 49 50 50 51 51 52 92 53 53 54 54 55 55 56 56 INFORMATION MENU AND s7 OTHERS 5 H Position 4 V Position Configuring H Position amp V Position Image Size Changing the Image Size Menu H Position amp Menu V Position Configuring Menu H Position amp Menu V Position Reset Initializing Settings Reset Language Changing the Language MagicEco Configuring MagicEco Off Timer On Off Configuring Off Timer On Off Off Timer Setting Configuring Off Timer Setting Key Repeat Time Configuring Key Repeat Time Customized Key Configuring Customized Key Display Time Configuring Display Time Menu Transparency Changing Menu Transparency INFORMATION Displaying INFORMATION Table Of Contents INSTALLING THE 58 Magic Tune SOFTWARE 58 What is MagicTune 58 Installing the Software 59 Removing the Software 60 MultiScreen 60 Installing the Software 61 Removing the Software TROUBLESHOOTING e2 Requirements Before Contacting GUIDE Samsung Customer Service Center 62 Testing the Product 62 Checking the Resolution and Frequency 62 Check the following
41. ng com latin_en English ECUADOR 1 800 10 7267 http www samsung com latin Spanish http www samsung com latin_en English EL SALVADOR 800 6225 http www samsung com latin Spanish http www samsung com latin_en English Appendix Appendix LATIN AMERICA GUATEMALA 1 800 299 0013 http www samsung com latin Spanish http www samsung com latin_en English HONDURAS 800 27919267 http www samsung com latin Spanish http www samsung com latin_en English JAMAICA 1 800 234 7267 http www samsung com NICARAGUA 00 1800 5077267 http www samsung com latin Spanish http www samsung com latin_en English PANAMA 800 7267 http www samsung com latin Spanish http www samsung com latin_en English PERU 0 800 777 08 http www samsung com PUERTO RICO 1 800 682 3180 http www samsung com TRINIDAD amp TOBAGO 1 800 SAMSUNG 726 7864 http www samsung com VENEZUELA 0 800 100 5303 http www samsung com EUROPE AUSTRIA 0810 SAMSUNG http www samsung com 7267864 0 07 min BELGIUM 02 201 24 18 http Awww samsung com be Dutch http www samsung com be_fr French BOSNIA 05 133 1999 http www samsung com BULGARIA 07001 33 11 normal tariff http www samsung com CROATIA 062 SAMSUNG 062 726 7864 http www samsung com CYPRUS 8009 4000 only from landline http www samsung com 30 210 6897691 from mobile and la
42. o this resolution Connecting and Using a Source Device Changing the Resolution on Windows 8 Go to Settings Control Panel Display Screen Resolution and change the resolution t Wr CommetPere Al Continet SE LER LERNT HET E2F7FFE PETifi 7 Mn coita tem Onplny Somme mshton 2 Connecting and Using a Source Device 3 1 Screen Setup Configure the screen settings such as brightness and color tone Brightness You can adjust the general brightness of the picture Range 0 100 A higher value will make the picture appear brighter K e This menu is not available when MagicBright is set to Dynamic Contrast mode e Not available if MagicEco is set to On 3 1 1 Configuring Brightness Press MENU on the product 2 Press 4 W to move to Picture and press 7 c on the product 3 Press A V to move to Brightness and press 7 08 on the product The following screen will appear 4 Adjust the Brightness using the A Y buttons 3 2 Screen Setup Contrast Adjust the contrast between the objects and background Range 0 100 A higher value will increase the contrast to make the object appear clearer A e This menu is not available when MagicBright is in Cinema or Dynamic Contrast mode e This menu is not available when MagicColor is in Full or Intelligent mode e This menu is unavailable when Color Effect is set 3 2 1 Configuring Contrast
43. or change from darker areas to brighter areas on the screen Changes to the screen brightness are expressed with black and white variation and grey scale refers to the medium area between black and white Changing the grey scale through Gamma adjustment will change the medium brightness on the screen Scanning rate Scanning rate or refresh rate refers to the frequency of screen refreshes Screen data is transmitted as it refreshes to display an image although the refreshing is invisible to the naked eye The number of screen refreshes is called scanning rate and is measured in Hz A scanning rate of 60Hz means that the screen refreshes 60 times per second The screen scanning rate depends on the performance of the graphics cards in your PC and monitor Horizontal Frequency Characters or images displayed on the monitor screen consist of numerous dots pixels Pixels are transmitted in horizontal lines which are then arranged vertically to create an image The horizontal frequency is measured in kHz and represents how many times horizontal lines per second are transmitted and displayed on the monitor screen A horizontal frequency of 85 means that the horizontal lines that make up an image are transmitted 85 000 times per second and the horizontal frequency is indicated in 85kHz Vertical Frequency One image is made of numerous horizontal lines The vertical frequency is measured in Hz and represents how many images can be created per secon
44. ower off the product remove the power cord and contact Samsung Customer Service Center page 70 e Otherwise an electric shock or fire may result Do not put a heavy object toy or sweets on top of the product e The product or heavy objects may fall as children try to reach for the toy or sweets resulting in a serious injury Before Using the Product 12 Before Using the Product U 2 During a lightning or thunderstorm power off the product and remove the power cable e An electric shock or fire may result Do not drop objects on the product or apply impact e An electric shock or fire may result Do not move the product by pulling the power cord or any cable e Otherwise the cable may be damaged and product failure an electric shock or fire may result If a gas leakage is found do not touch the product or power plug Also ventilate the area immediately e Sparks can cause an explosion or fire Do nat lift or move the product by pulling the power cord or any cable e Otherwise the cable may be damaged and product failure an electric shock or fire may result Do not use or keep combustible spray or an inflammable substance near the product e An explosion or fire may result Ensure the vents are not blocked by tablecloths or curtains e Otherwise a fire may result from an inc
45. pany s product e f customer requests instructions on how to use the network or another company s program e If customer requests software installation and setup for the product e If a service technician removes cleans dusts or foreign materials inside of the product e _ lf customer requests an installation additionally after purchasing a product through home shopping or online A Product damage caused by customer s fault Product damage caused by customer s mishandling or wrong repair If a product damage is caused by e External impact or drop e use of supplies or separatly sold product unspecified by Samsung e repair from a person besides an engineer of outsourcing service company or partner of Samsung Electronics Co Ltd e remodeling or repairing the product by customer e using it with incorrect voltage or non authorised electrical connections e not following the cautions in User Manual Others e If product fails by natural disaster lightning fire earthquake flood damage etc e If consumable components are all used up Battery Toner Fluorescent lights Head Vibrator Lamp Filter Ribbon etc W4 If customer requests a service in case the product has no defect service fee may be charged So please read User Manual first Appendix Correct Disposal of This Product Waste Electrical amp Electronic Equipment pa Applicable in countries with separate collection systems
46. r Windows OS manual for further details Connecting and Using a Source Device 2 3 3 Setting Optimum Resolution An information message about setting optimum resolution will appear if you power on the product for the first time after purchase Select a language on the product and change the resolution on your PC to the optimum setting The optimal resolution for this monitor is as follows Follow the above setting to set the resolution English v Ka 4 Auto O 1 Press A V to move to the language you want and press 2 G 2 To hide the information message press MENU NG e Ifthe optimum resolution is not selected the message will appear up to three times for a specified time even when the product is turned off and on again e _ The optimum resolution can also be selected in Control Panel on your PC 2 Connecting and Using a Source Device Connecting and Using a Source Device 2 3 4 Changing the Resolution Using a PC K e Adjust the resolution and refresh rate in Control Panel on your PC to obtain optimum picture quality e The picture quality of TFT LCDs may degrade if the optimum resolution is not selected Changing the Resolution on Windows XP Go to Control Panel Display Settings and change the resolution E Control Panel amp Control Panel File Edit View Favorites Tools He Set Program Access and er Defaults QO O B Ps Broken 2 ana Ta amp control Panel NG Printe
47. reased internal temperature Do not insert a metallic object a chopstick coin hair pin etc or inflammable object paper match etc into the vent or ports of the product e If water or any foreign substance enters the product be sure to power off the product remove the power cord and contact Samsung Customer Service Center page 70 e Product failure an electric shock or fire may result Do not place objects containing liquid vases pots bottles etc or metallic objects on top of the product If water or any foreign substance enters the product be sure to power off the product remove the power cord and contact Samsung Customer Service Center page 70 e Product failure an electric shock or fire may result Before Using the Product EEJ Before Using the Product A Caution Leaving the screen fixed on a stationary image for an extended period of time may cause afterimage burn in or defective pixels e If you are not going to use the product for an extended period of time activate power saving mode or a moving picture screen saver Disconnect the power cord from the power socket if you do not plan on using the product for an extended period of time vacation etc e Otherwise a fire may result from accumulated dust overheating an electric shock or electric leakage
48. rs and Faxes TS Er ra Accessibility Add Hardware Add or Administrative Adobe Gamma Help and Support Options Remov Tools p seach aR pw 2 Folder Options Fonts Gana Intel GMA All Programs gt TI Run g lers Driver For s0 Des P Log Off 0 Turn OFF Keyboard Mail Mouse Network Network Setup ma Connections Wizard Theses Desktop Sciven Sarver Agpeaarrce Setings Drag the moniter icons to march the physical arrangement of your monitors Display i DI Connecting and Using a Source Device Changing the Resolution on Windows Vista a Windows Live Messenger Download W Norton AntiVirus Windows DVD Maker Windows Meeting Space gt AllPrograms tart Search p ai a 7 Ei ET Pick a different Mouse pointer You can also change how the mouse poster looks during such activities as clicking and selecting Theme Change the theme Themes can change a wide range of visual and auditory elements at one time including the appearance of menus icons backgrounds sereen cavers some computer sounds and mouse pointers Display Settings Adjust your monitor resolution which changes the view so more or fewer items fit on the screen You can also control monitor flicker refresh rate Go to Control Panel Personalization Display Settings and change the resolution Pertonaslizati Performance Phone and Infcematio Modem on Printer
49. s To remove MagicTune complete the following steps 1 D Oa NA GUN Click Start select Settings and select Control Panel from the menu For Windows XP click Start and select Control Panel from the menu Double click the Add or Remove Programs icon in the Control Panel In the Add Remove window find and select Magic Tune Mso that it is highlighted Click Change or Remove Programs to remove the software Select Yes to start removing MagicTune Wait until a message box appears informing you that the software has been removed completely We For technical support the FAQ frequently asked questions or information about the software upgrade for MagicTune please visit our website http www samsung com us consumer learningresources monitor magetune pop_intro html 8 2 Installing the Software MultiScreen im MultiScreen MultiScreen enables users to use the monitor by partitioning multiple sections 8 2 1 Installing the Software 7 Insert the installation CD into the CD ROM drive 2 Select the MultiScreen setup program NG If the pop up screen for the software installation does not appear on the main screen find and double click the MultiScreen setup file on the CD ROM 3 When the Installation Wizard appears click Next 4 Follow the instructions given on the screen to proceed with installation LE The software may not work properly if you do not restart the computer
50. s Problem Programs Realtek HD Reports and Features Audio M KKK KHER KEK KKK KHER RHEE Connecting and Using a Source Device Changing the Resolution on Windows 7 Go to Control Panel Display Screen Resolution and change the resolution a Remote Desktop Connection Adjust your computer s settings we Microsoft Word 2010 w Action Center ra Administrative Tools gt Wireless Display Manager mg AutoPlay Backup and Restore EH Microsoft Office Excel 2007 SL BitLocker Drive Encryption SM Color Management en ee e Default Programs GB Desktop Gadgets a Device Manager aid Devices and Printers ke Display Ease of Access Center TET x m TO Control Panel gt All Control Panel Items Display 9 f Seorch Control Ponet 2 Control Panel Home Change the appearance of your displays Make it easier to read what s on your screen Adjust resolution You can change the size of text and other items on your screen by choosing one of these options To temporarily enlarge just part of the screen use the Magnifier Calibrate color tool Change display settings Connect to a projector Senate 100 ladat Preview Adjust ClearType text Set custom text size DPD Medium 125 ra EEE Tma a cm your man Bagay see als o Noa prayer bar pres me un Personalization A Some items may not fit on your screen if you choose this einigen DAGA NG Pre setting while your display is set t
51. s on the screen look distorted Check the cable connection to the product Refer to 2 3 Connecting and Using a PC The screen is not clear The screen is blurry Adjust Coarse page 36 and Fine page 37 Remove any accessories video extension cable etc and try again Set the resolution and frequency to the recommended level Refer to 10 1 General The screen appears unstable and shaky Check that the resolution and frequency for the There are shadows or ghost images left on the screen PC are within the range of resolution and frequency compatible with the product Next if required change the settings referring to Standard Signal Mode Table page 69 in this manual and the INFORMATION menu on the product The screen is too bright The screen is too dark Adjust Brightness page 32 and Contrast page 33 Screen color is inconsistent Change the COLOR settings Refer to Configuring Tint The colors on the screen have a shadow and are distorted Change the COLOR settings Refer to Configuring Tint White does not really look white Change the COLOR settings Refer to Configuring Tint There is no image on the screen and the power LED blinks every 0 5 to 1 second The product is operating in power saving mode Press any key on the keyboard or move the mouse to return to normal operating mode Source device issue A beeping sound
52. stable surface so that the screen is facing downwards 4 Gern Insert the Stand Connector into Check if the Stand Connector is Turn the connecting screw at the the Stand in the direction shown firmly connected bottom of the stand fully so that it by the figure is completely fixed Place a soft cloth over the table Hold the main body of the Caution to protect the product and place product with your hand as Do not hold the product upside the product onto the cloth so shown by the figure down only by the stand that the front of the productis push the assembled stand into facing downwards the main body in the direction of the arrow as shown in the figure A The color and shape of parts may differ from what is shown Specifications are subject to change without notice to improve quality Preparations 1 3 2 Adjusting the Product Tilt K The color and shape of parts may differ from what is shown Specifications are subject to change without notice to improve quality e You can adjust the tilt of your monitor e Hold the lower part of the product and adjust the tilt carefully 1 3 3 Anti theft Lock An anti theft lock allows you to use the product securely even in public places The locking device shape and locking method depend on the manufacturer Refer to the user guide provided with your anti theft locking device for details The lock device is sold separately
53. ton when the button is pressed 6 6 1 Configuring Key Repeat Time Press MENU on the product 2 Press A W to move to SETUP amp RESET and press t c on the product 3 Press 4 W to move to Key Repeat Time and press 13 c on the product The following screen will appear SETUP amp RESET Acceleration 1 sec 2 sec No Repeat gt AUTO 0 e Acceleration 1 sec or 2 sec can be selected If No Repeat is selected a command responds only once when a button is pressed 4 Press M V to move to the option you want and press 5 0 5 The selected option will be applied 6 Setup and Reset 53 Setup and Reset 6 7 Customized Key You can customize Customized Key as follows 6 7 1 Configuring Customized Key Press MENU on the product 2 Press 4 W to move to SETUP amp RESET and press t c on the product 3 Press 4 V to move to Customized Key and press 3 C on the product The following screen will appear SETUP amp RESET MagicBright MagicEco Image Size La gt e MagicBright MagicEco Image Size 4 Press A W to move to the option you want and press 5 0 5 The selected option will be applied 6 Setup and Reset 54 Setup and Reset 6 8 Display Time Set the on screen display OSD menu to automatically disappear if the menu is not used for a specified period of time Display Time can be used to specify the time after which you want the OSD menu to
Download Pdf Manuals
Related Search