Samsung ND020QHXCA manual do usuário
Contents
1. e Fan may not operate for about 3 5 minutes at the beginning to prevent any cold blasts while the air conditioner is warming up KK e Air flow can be adjusted manually See page 17 for instructions e Since the air conditioner heats the room by taking heat energy from outdoor air the heating capacity may decrease when outdoor temperatures are extremely low If you feel the air conditioner insufficiently heats using an additional heating appliance in combination with the air conditioner is recommended Neo Forte ND IB E 32582 1 indd 16 2011 06 15 m 6 06 34 ADJUSTING THE AIR FLOW DIRECTION Air flow can be directed to your desired position Vertical air flow HSITON3I Air flow blades move up and down 1 Press the Air swing 5 button on the remote control Air swing indicator will be on and air flow blades move up and down continuously to circulate the air To keep the air flow direction in a constant position press the Air swing 5 button on the remote control again Horizontal air flow Make sure one of the blade pins that stick out of the air flow blades are not broken 1 Move the blade pin lever left or right to keep the air flow direction in a constant position you prefer Be extremely careful with your fingers while adjusting the Horizontal air flow direction amon There is a potential risk of personal injury when the unit is mishandled 17 Neo Fort2. 4 Insert the Air filter back in its original position 5 Close the front panel 2011 06 15 m 6 06 48 Anti allergy filter Washable foam based Anti allergy filter leads to reduction in allergens that thrive in polluted air The filter is cleaned with a vacuum or by hand washing 1 Remove the front panel HSITON3I Tightly grab both side of the front panel and lift up the panel to open Then slide the panel towards you to remove the panel HT ANAN TAT im 7 nn CO NN Capa Hr E i TWO Il i ll ll TA Ca j of Il Jl ii Mi M ill AAAI A N 4 e Anti allergy filter can be placed in any 4 slots beneath the air filter e Front panel of your air conditioner is actually not detachable 3 Clean the Anti allergy filter with a vacuum cleaner or soft brush Then rinse it with running water and dry it in a ventilated area R 4 Install the Anti allergy filter back in position 5 Close the front panel KK Clean the Anti allergy filter every 3 months The cleaning term may differ on usage and environmental conditions 25 Neo Forte ND IB E 32582 1 indd 25 2011 06 15 m 6 06 51 Cleaning and maintaining the air conditioner REP
3. Neo Forte ND IB E 32582 1 indd 26 2011 06 15 m 6 06 51 MAINTAINING YOUR AIR CONDITIONER If the air conditioner will not be used for an extended period of time dry the air conditioner to maintain it in best condition 1 Dry the air conditioner thoroughly by operating in Fan mode for 3 to 4 hours and disconnect the power plug There may be internal damage if moisture is left in components HSITONA 2 Before using the air conditioner again dry the inner components of the air conditioner again by running in Fan mode for 3 to 4 hours This helps remove odors which may have generated from dampness Periodical checks Refer to the following chart to maintain the air conditioner properly BAGO Every 4 Oncea Type Description Monthly a EG year Clean the air filter 1 Clean the condensate drain pan 2 ee Thoroughly clean the heat exchanger 2 Clean the condensate drain pipe 2 Replace the remote control batteries 1 Clean the heat exchanger on the outside of the pa unit 2 Clean the heat exchanger on the inside of o the unit 2 Clean the electric components with jets of o air 2 Outdoor unit Verify that all the electric components are firmly pa tightened 2 Clean the fan 2 Verify that all the fan assembly is firmly o tightened 2 Clean the condensate drain pan 2 K The checks and maintenance operations described are essential to guarantee the
4. Neo Forte_ND _IB_E 32582 1 indd 28 2011 06 15 m 6 06 51 Appendix TROUBLESHOOTING Refer to the following chart if the air conditioner operates abnormally This may save time and unnecessary expenses PROBLEM SOLUTION The air conditioner does not operate immediately after it has been restarted e Because of the protective mechanism the appliance does not start HSITDNA operating immediately to keep the unit from overloading The air conditioner will start in 3 minutes The air conditioner does not work at all Check that the power plug is properly connected Insert the power plug into the wall socket correctly Check if the circuit breaker is switched off Check if there is a power failure Check your fuse Make sure it is not blown out The temperature does not change Check if you selected Fan mode Press the Mode button on the remote control to select another mode The cool warm air does not come out of the air conditioner Check if the set temperature is higher lower than the current temperature Press the Temperature A or V button on the remote control to change the set temperature Press the Temperature A or V button to increase or decrease the temperature Check if the air filter is blocked by dirt Clean the Air filter every two weeks Check if the air conditioner has just been turned on If so wait 3 minutes The fan speed does not change Check if you selected
5. Set Cancel button to activate the Off timer When you set the time there can be two possible options On timer is shorter than Off timer fe 2 S BUM wh TI am m 7IF The air conditioner will turn on and then off automatically Set up should be done while the air conditioner is off Off Timer KI N For example If the On timer is set at 3 hours and the Off timer at 5 hours the air conditioner will turn off automatically 3 hours after the set time and then operate for next 2 hours before turning off automatically On timer is longer than Off timer fe 2 m a The air conditioner will turn off and then on automatically Set up should be done while the air conditioner is operating I Gino fe o mn m For example If the On timer is set at 3 hours and the Off timer at 1 hour the air conditioner will turn off automatically an hour after the set time and remain off for 2 hours before turning on automatically K See page 20 for more detail instructions on setting Off timer To deactivate the timer combination 1 Press the Power O 8 Set Cancel button on the remote control Both of the On and Off timer will be canceled and the indicators will disappear 21 Neo Forte ND IB E 32582 1 indd 21 2011 06 15 m 6 06 42 Using advanced functions SETTING THE TIMER good sleep mode good sleep mode allows you to set a comfortable sleep temperature while savin
6. 800 299 0013 www samsung com HONDURAS 800 27919267 www samsung com JAMAICA 1 800 234 7267 www samsung com NICARAGUA OO 1800 5077267 www samsung com PANAMA 800 7267 www samsung com PERU 0O 800 777 08 www samsung com PUERTO RICO 1 800 682 3180 www samsung com Ja a 1 800 SAMSUNG 726 7864 www samsung com VENEZUELA 0 800 100 5303 www samsung com Neo Forte ND IB E 32582 1 indd 48 2011 06 15 m 6 08 14
7. Auto or Dry mode The air conditioner automatically adjusts the fan speed to Auto in Auto Dry mode Timer function does not set Check if you press the Power O 8 Set Cancel button on the remote control after you have set the time Odors permeate in the room during operation Check if the appliance is running in a smoky area or if there is a smell entering from outside Operate the air conditioner in Fan mode or open the windows to air out the room The air conditioner makes a bubbling sound A bubbling sound may be heard when the refrigerant is circulating through the compressor Let the air conditioner operate in a selected mode Water is dripping from the air flow blades Check if the air conditioner has been cooling for an extended period of time with the air flow blades pointed downwards Condensation may generate due to the difference in temperature Remote control is not working Check if your batteries are depleted Make sure batteries are correctly installed Make sure nothing is blocking your remote control sensor Check that there are strong lighting apparatus near the air conditioner Strong light which comes from fluorescent bulbs or neon signs may interrupt the electric waves Neo Forte ND IB E 32582 1 indd 29 29 2011 06 15 m 6 06 51 Appendix OPERATION RANGES The table below indicates the temperature and humidity ranges the air conditioner can be operated within Re
8. E 32582 1 indd 23 2011 06 15 m 6 06 45 Cleaning and maintaining the air conditioner CLEANING THE EXTERIOR 1 Wipe the surface of the unit with a slightly wet or dry cloth when needed Do not use Benzene Thinner or Clorox They may damage the surface of the air conditioner and can create a risk of fire CAUTION CLEANING THE FILTER When cleaning the filter make sure to unplug the power from the unit No special tools are needed to clean it 24 Neo Forte ND IB E 32582 1 indd 24 Air filter Washable foam based air filter captures large particles from the air The filter is cleaned with a vacuum or by hand washing 1 Remove the front panel Tightly grab both side of the front panel and lift up the panel to open Then slide the panel towards you to remove the panel 2 Grab the handle and lift it up Then pull the Air filter towards you INN a C J j MTT 3 Clean the Air filter with a vacuum cleaner or soft brush If dust is too heavy then rinse it with running water and dry it in a ventilated area iY e For the best conditions repeat every two weeks If the Air filter dries in a confined or humid area odors may generate If it occurs re clean and dry it in a well ventilated area
9. Press the Power O 8 Set Cancel button on the remote control to active it on The remote control display will show the hour s you have set The air conditioner will turn off automatically at set time and then Off timer indicator disappears If Off timer is not set within 10 seconds the air conditioner will end setting if e Setting time allows you to change by pressing the Off Timer button Press the Off Timer button to change the time setting and then press the Power amp Set Cancel button to active it on e You can combine Off timer function with On timer function to turn on and then off the air conditioner at the desired time See page 21 for instructions To deactivate the Off timer 1 Press the Power O 8 Set Cancel button on the remote control Off timer you set will be canceled and Off timer indicator will disappear 20 Neo Forte ND IB E 32582 1 indd 20 2011 06 15 m 6 06 40 Combining On timer and Off timer You can combine the On timer and Off timer together for more convenient use of the timer function 1 Set the On timer Press the On Timer button ue j HSITDNA Set the time with On Timer button lt gt s5 Press Power amp Set Cancel button to activate the On timer 3 pn f 2 A amp 0E i Spa 4 See page 19 for more detail instructions on setting On timer 2 Set the Off timer Press the Off Timer button Set the time with Off Timer button Press Power amp
10. _IB_E 32582 1 indd 18 2011 06 15 m 6 06 36 SETTING THE TIMER This advanced Timer function allows you to turn on off your air conditioner automatically even when you are away Simply set the time and your air conditioner will turn on off automatically m Z G On timer N e This function allows you to turn on the air conditioner automatically within the time range of a 24 hours On timer is available while your air conditioner is on off GD 1 Press the On Timer button on the remote control On timer indicator blinks on the remote control display 2 Set the time you want the air conditioner to turn on automatically Press the On Timer button on the remote control DS Pera D to change the time setting while On timer pA ce indicator is blinking You can set the time up to 24 hours increasing in e NERI 30 minute unit up to first 3 hours and in hourly unit Sant CIJ after first 3 hours 3 Press the Power O 8 Set Cancel button on the remote control to active it on The remote control display will show the hour s you have set The air conditioner will operate automatically at set time and then On timer indicator disappears If On timer is not set within 10 seconds the air conditioner will end setting 4 Set the operating mode Press the Mode button on the remote control until the desired mode appears on the remote control display gar T
11. ctosenes PR GA PP 24 Replacing NE NEE mama NA ANA mGA AA ANAKAN 26 Maintaining your air conditione PN aaa ANAN AGA 27 Maa aLe e I csa AE AE E A E E A AE A AATE TEN ET 29 DESEE ES NO EEA OAA AAE ANA AA EA A AT AA 29 Operation ANGES eee ee ere een A a E EEEREN eee ona ee ere 30 INSTALLATION PARTS Safety PFECAUTIONS AABANGAN AKA 31 Choosing the installation location ssssssssssssssssssssssssssscsssssssssessnssenssenscsnscssssnssenssssscessssssssessssssssesssesssenssensees 33 ACCESSOS nA tana DAN AANI AD NANA AA AN AA AA ANA 34 FIXING theinstallaton plate AKA AG 35 Purging the indoor unit aNG 35 Installing and connecting the assembly pipe of the indoor unit sssssssssssssssssssssssssssssosoocoooccoooeccoeeecssssess 36 Cutting OF Extending the PIPE UA BAKANTENG BKA 37 Installing and connecting the drain hose of the indoor unit sssssscssscsssccssscnsscssscssscenscenssessscenscenscesssees 38 Changing direction OF the drain NOSE AGANG AGA KA KGAAN 39 MINING WON AA AG BAGAN AGA A AE A 40 Assigning address to INABOLUNI NI aa AA NGANGA GAGANA GG AAAGG 43 Additional LL hsoistadubte neuen tetasvasastasscued enoeseseeditataoase 44 Performing leak test amp insulation anG NN GAGANA 45 Final check and trial Operation s ssscssscsscsscssssnscnsscssenscssssssenscsssenseavssssenscescensensesssensesscensensesscensesscsseensesseensenes 46 Providing information FOF USEF ANGARA NANANA GAGA 47 Neo Forte ND IB E 32582 1 indd 3 2011
12. efficiency of the air conditioner The frequency of these operations varies according to the characteristics of the area the amount of dust etc 1 The described operations should be performed more frequently if the area of installation is very dusty 2 These operations must always be performed by qualified personnel For more detailed information see the Installation Manual Neo Forte ND IB E 32582 1 indd 27 27 2011 06 15 m 6 06 51 Cleaning and maintaining the air conditioner MAINTAINING YOUR AIR CONDITIONER Internal protections via the unit control system This internal protection operates if an internal fault occurs in the air conditioner Type Description Against cold air The internal fan will be off to against cold air when the heat pump is heating De ice cycle The internal fan will be off to against cold air when the heat pump is heating Anti protection of The compressor will be off to protect internal battery when the air conditioner internal battery operates in Cool mode Protect The air conditioner does not start operating immediately to protect the com compressor pressor of the outdoor unit after it has been started iY If the heat pump is operating in Heat mode De ice cycle is actuated to remove frost from an outdoor unit that may have deposited at low temperatures The internal fan is switched off automatically and restarted only after the de ice cycle is completed 28
13. regulations in force with slings trucks scaffolding or any other means of elevation won t be considered in warranty and charged to end user POWER SUPPLY LINE FUSE OR CIRCUIT BREAKER Always make sure that the power supply is compliant with current safety standards Always install the air conditioner in compliance with current local safety standards Always verify that a suitable grounding connection is available Verify that the voltage and frequency of the power supply comply with the specifications and that the installed power is sufficient to ensure the operation of any other domestic appliance connected to the same electric lines Always verify that the cut off and protection switches are suitably dimensioned Verify that the air conditioner is connected to the power supply in accordance with the instructions provided in the wiring diagram included in the manual Always verify that electric connections cable entry section of leads protections are compliant with the electric specifications and with the instructions provided in the wiring scheme Always verify that all connections comply with the standards applicable to the installation of air conditioners CAUTION Make sure that you earth the cables Do not connect the earth wire to the gas pipe water pipe lighting rod or telephone wire If earthing is not complete electric shock or fire may occur Install the circuit breaker If the circuit breaker is not
14. service company gt Failing to do so may result in electric shock fire explosion problems with the product or injury Install a switch and circuit breaker dedicated to the air conditioner gt Failing to do so may result in electric shock or fire Fix the outdoor unit firmly so that the electric part of the outdoor unit is not exposed gt Failing to do so may result in electric shock or fire O Do not install this appliance near a heater inflammable material Do not install this appliance in a humid oily or dusty location in a location exposed to direct sunlight and water rain drops Do not install this appliance in a location where gas may leak gt This may result in electric shock or fire Never install the outdoor unit in a location such as on a high external wall where it could fall gt If the outdoor unit falls it may result in injury death or property damage B This appliance must be properly grounded Do not ground the appliance to a gas pipe plastic water pipe or telephone line gt Failure to do so may result in electric shock fire an explosion or other problems with the product gt Never plug the power cord into a socket that is not grounded correctly and make sure that it is in accordance with local and national codes FOR INSTALLATION CAUTION O Install your appliance on a level and hard floor that can support its weight gt Failing to do so may result in abnormal vibrations noise or problems with
15. smell or smoke unplug the power plug immediately and contact your nearest service center gt Failing to do so may result in electric shock or fire In the event of a gas leak such as propane gas LP gas etc ventilate immediately without touching the power line Do not touch the appliance or power line gt Do not use a ventilating fan gt A spark may result in an explosion or fire To reinstall the air conditioner please contact your nearest service center gt Failing to do so may result in problems with the product water leakage electric shock or fire gt A delivery service for the product is not provided If you reinstall the product in another location additional construction expenses and an installation fee will be charged gt Especially when you wish to install the product in an unusual location such as in an industrial area or near the seaside where it is exposed to the salt in the air please contact your nearest service center Neo Forte_ND _IB_E 32582 1 indd 5 2011 06 15 mm 6 06 11 Safety precautions FOR USING AA WARNING Do not touch the circuit breaker with wet hands gt This may result in electric shock Do not strike or pull the air conditioner with excessive force gt This may result in fire injury or problems with the product Do not place an object near the outdoor unit that allows children to climb onto the machine gt This may result in children seriously injuring themselves Do no
16. the indoor unit Upon delivery there may be inert gas inside the indoor unit Purge the gas from the indoor unit before connecting the assembly pipe 1 Unscrew the caps at the end of each pipe a wane a Result All inert gas escapes from the indoor unit To prevent dirt or foreign substances from getting into the pipes during installation do NOT remove the caps completely until you are ready to connect the pipe 35 Neo Forte_ND _IB_E 32582 1 indd 35 2011 06 15 m 6 07 05 Installing and connecting the assembly pipe of the indoor unit Connect indoor and outdoor units with field supplied copper pipes by means of flare connections Use insulated seamless refrigeration grade pipe only Cu DHP type according to 1501337 degreased and deoxidized suitable for operating pressures of at least 4200 kPa and for burst pressure of at least 20700 kPa Under no circumstances must sanitary type copper pipe be used There are 2 refrigerant pipes of different diameters The smaller one is for the liquid refrigerant Thelarger one is for the gas refrigerant Ashort pipe is already fitted to the air conditioner You may need to extend the pipe using the assembly pipe optional The connection procedure for the refrigerant pipe varies aan according to the exit position of the pipe when facing the wall Right A Left B Underside C NG Rear a 1 Cut out the appropriate knock out pi
17. to indoor unit 1 Before installing the indoor unit assign an address to the indoor unit according to the air conditioning system plan 2 The address of the indoor unit is assigned by adjusting MAIN SWO1 SW02 and RMC SWO3 SWOA rotary switches HSITDNA SW01 SWo2 swo3 swoa Cover PCB NU SW05 SW06 SW07 3k The designs and shape are subject to change according to the model Setting Main Address The MAIN address is for communication between the indoor unit and the outdoor unit Therefore you must set it to operate the air conditioner properly You can set the MAIN address from 00 to 99 by mixing SWO1 and SW02 The MAIN address from 00 to 99 should differ from each other Check the indoor unit address on the plan that you are to install and set the address according to the plan You may not need to set main address if you selected Auto Address Setting from the outdoor unit see details on the outdoor unit installation manual When MAIN address is set as 12 Setting RMC Address The SW03 SW04 RMC switch is the address setting switch for controlling the indoor unit with the centralized controller You must set the SW03 SW04 and K2 switch when using the centralized controller When RMC address is set as 12 43 Neo Forte_ND _IB_E 32582 1 indd 43 2011 06 15 m 6 08 12 Additional functions Function ON External room sensor Not use Centr
18. 06 15 m 6 06 10 Safety precautions Before using your new air conditioner please read this manual thoroughly to ensure that you know how to safely and efficiently operate the extensive features and functions of your new appliance Because the following operating instructions cover various models the characteristics of your air conditioner may differ slightly from those described in this manual If you have any questions call your nearest contact center or find help and information online at www samsung com Important safety symbols and precautions A WARNING Hazards or unsafe practices that may result in severe personal injury or death A CAUTION Hazards or unsafe practices that may result in minor personal injury or property damage O Follow directions S Do NOT attempt Make sure the machine is grounded to prevent electric shock Unplug the power plug from the wall socket Q Do NOT disassemble FOR INSTALLATION WARNING O Use the power line with the power specifications of the product or higher and use the power line for this appliance only In addition do not use an extension line gt Extending the power line may result in electric shock or fire gt Do not use an electric transformer It may result in electric shock or fire gt If the voltage frequency rated current condition is different it may cause fire The installation of this appliance must be performed by a qualified technician or
19. 1000XAk lt 1096 of input voltage V Lk Distance among each indoor unit m Ak Power cable specification MM ik Running current of each unit A Example of Installation Total power cable length L 100 m Running current of each units 1 A Total 10 indoor units were installed or MCCB ELB 10 A 10 m Apply following equation i Coefx35 6XLkXik k 1 1000XAk NG ss Calculation Installing with 1 sort wire 220 V Installing with 2 different sort wire Neo Forte ND __ 2 5 MM 2 2 V 2 5 MM i 2 0 V 9 A Indoor unit1 1096 of input voltage V 2 24 2 04 1 8 1 54 1 3 1 1 0 9 0 7 0 4 0 2 11 2 V 4 0 mm i 1 4 V 4 0 mm 1 2 V 1 44 1 24 1 8 1 54 1 34 1 1 0 9 0 7 0 4 0 2 10 5 V IB_E 32582 1 indd 41 Indoor unit2 208 8 V Within 198V 242V it s okay 209 5 V Within 198V 242V it s okay 41 2011 06 15 m 6 08 10 Wiring work CAUTION Select the power cable in accordance with relevant local and national regulations Wire size must comply with local and national code For the power cable use the grade of HO7RN F or HO5RN F materials You should connect the power cable into the power cable terminal and fasten it with a clamp The unbalanced power must be maintained within 10 of supply rating among whole indoor units If the power is unbalanced greatly it may shorten the life of the condenser If the unbalance
20. EEV kit Indoor Unit 1 Indoor Unit 2 Indoor Unit 3 SERATE a ELCB Essential Installation tl en l Hit AR RE ower off before connecting any wires Indoor PBA will be damaged while V1 V2 F3 F4 short each Indoor Unit4 Indoor Unit5 Indoor Unit 6 other K Ceiling wall mounted indoor unit I Selecting compressed ring terminal Norminal dimensions for cable mm Norminal dimensions for screw mm Standard dimension mm Allowance mm Standard dimension mm Allowance mm Standard dimension mm Standard Max dimension mm Allowance mm 15 6 6 3 4 1 7 4 3 0 2 40 4 4 4 4 4 Neo Forte ND IB E 32582 1 indd 40 2011 06 15 I Specification of electronic wire Power supply MCCB ELB or ELCB Earth cable Max 242V Min 198V XA 30MMA 2 5mm 2 5mm 0 1 sec Decide the capacity of ELCB or MCCB ELB by below formula The capacity of ELCB or MCCB ELB X A 1 25 X 1 1 X YAi X The capacity of ELCB or MCCB ELB 2 Ai Sum of Rating currents of each indoor unit Refer to each installation manual about the rating current of indoor unit 0 75 1 5mm72 SZ Rating current HSITDNA uw a ang current ND QHKK 020 Decide the power cable specification and maximum length within 10 power drop among indoor units n k 1 coef 1 55 Coefx35 6XLkXik
21. Ifyou want to shorten the pipe cut it using a pipe cutter ensuring that the cut edge remains at 90 with the side of the pipe There are some examples of correctly and incorrectly cut edges below Oblique Rough 3 To prevent a gas leak remove all burrs at the cut edge of the pipe using a reamer 4 Carry out flaring work using flaring tool as shown below Flaring tool A Clutch type Wing nut type Copper pipe Flare nut pipe Outer diameter mm Flare tool for Conventional flare tool R410A clutch type Clutch type Wing nut type 0 0 5 1 0 1 5 1 5 2 0 9 52 12 70 15 88 5 Check if you flared the pipe correctly There are some examples of incorrectly flared pipes below Inclined Damaged Surface Cracked Uneven Thickness 6 Align the pipes and tighten the flare nuts first manually and then with a torque wrench applying the following torque HSITONA 145 4175 8 70 9 10 333 407 12 80 13 20 Outer diameter Connection Flare dimension Flare shape mm Torque kgf cm mm mm 12 70 505 615 16 20 16 60 15 88 630 769 19 3019 70 CAUTION In case of needing brazing you must work with Nitrogen gas blowing Neo Forte ND IB E 32582 1 indd 37 37 2011 06 15 m 6 07 09 Installing and connecting the drain hose of the indoor unit When installing the drain hose for the indoor unit check if condensation draining is adequate When passing the drain hose through the 65 mm hole dril
22. LACING THE FILTER Replacement filter may be purchased from the retail store or ordered from the dealer where you purchased the unit If you cannot find one please call a contact center Deodorizing filter Deodorizing filter absorbs efficiently cigarette smoke pet odors and other unpleasant smells Deodorizing filter cleaning is simple just remove old filter and install a new one 1 Remove the front panel Tightly grab both side of the front panel and lift up the panel to open Then slide the panel towards you to remove the panel mr oT LLL COT M el seed MMMM a X l o j CITI TITA Mm LI uf LITITT NINI ua TT T ni NANANAHAN DAANEN DELALA AANNAM TT T LU 4 e Deodorizing filter can be placed in any 4 slots beneath the air filter e Front panel of your air conditioner is actually not detachable 3 Install the new Deodorizing filter back in position 4 Close the front panel KK e The replacement timing of the Deodorizing filter differs depending on usage and environmental conditions e Even if Deodorizing and Anti allergy filters are installed in an inverted position it will not affect its filtration system 26
23. ND _IB_E 32582 1 indd 34 2011 06 15 m 6 06 57 Fixing the installation plate Before fixing the installation plate to the wall or window frame you must determine the position of the 65mm hole through which the cable pipe and hose pass to connect the indoor unit to the outdoor unit When facing the wall the pipe and cable can be connected from the T 2 n O amp Right a O N O T T rar T Nn Left Underside right a Rear right or left y y 1 Determine the position of the pipe and drain hose hole as seen in the picture and drill the hole with an inner diameter of 65mm so that it slants slightly downwards If you fix the indoor unit to a Follow step s Unit mm X020 032 040XX 2zzz A2A IIL fkck zARXOIN I ee Wall 3 Pipe hole Window frame 4 to 6 7 lap 3 Fixtheinstallation plate to the wall giving attention to the weight of the indoor unit gt If you mount the plate to a concrete wall with anchor Unit mm 056 060 072 bolts the anchor bolts must not project more than SS 20mm Pipe hole See rrcrvrvrcrcrvrvrr 065mm Sse 4 Determine the positions of the wooden uprights to be ia Sel attached to the window frame bl 5 Attach the wooden uprights to the window frame giving attention to the weight of the indoor unit 6 Attach the installation plate to the wooden uprights using tapping screws as seen in the picture Purging
24. Wall Mounted Type Series Neo Forte with EEV ND QH x 100 Recycled Paper imagine the possibilities Thank you for purchasing this Samsung product To receive more complete service please register your product at www samsung com register OOP DB98 32582A 1 en 2011 06 15 m 6 10 20 Neo Forte ND IB E 32582 1 indd 49 Features of your new air conditioner e Cool Summer Offer On those hot sweltering summer days and long restless nights there is no better escape from the heat than the cool comforts of home Your new air conditioner brings an end to exhausting hot summer days and lets you rest This summer beat the heat with your own air conditioner e Cost Efficient System Your new air conditioner not only provides maximum cooling power in the summer but can also be an efficient heating method in the winter with the advanced Heat pump system This technology is up to 300 more efficient than electrical heating so you can further reduce its running cost Now meet year round needs with one air conditioner e A Look for Everywhere The elegant and harmonious design gives priority to the esthetics of your space and complements any of your existing interior d cor With its soft color and rounded edge shape the new air conditioner adds class to any room Enjoy what your air conditioner offers both functionally and esthetically good sleep function good sleep mode allows you to set a comfortable sleep temper
25. alized controller Not use K K1 OFF aang mode Setting temperature compensation value 0 C Thermo OFF Fan OFF Function Heating Current Temperature Compensation Indoor Expansion Valve For Heating Stop 80 or 160 step 80 or 160 step 80 step last for at least 1 hour Not use Not use Use Use 44 Neo Forte ND IB E 32582 1 indd 44 Thermal ON Operation ON KI K2 K3 K4 K5 K6 K7 K8 NG SW06 i Z K9 K10 K11 K12 it SW07 i 2011 06 15 m 6 08 13 Performing leak test amp insulation Leak test LEAK TEST WITH NITROGEN before opening valves In order to detect basic refrigerant leaks before recreating C D the vacuum and recirculating the R410A it s responsible of installer to pressurize the whole system with nitrogen using a pressure regulator at a pressure above 4 1MPa gauge LEAK TEST WITH R410A after opening valves Before opening valves discharge all the nitrogen into the lt y gt system and create vacuum After opening valves check leaks using a leak detector for refrigerant R410A HSITDNA CAUTION Discharge all the nitrogen to create a vacuum and charge the system Insulation After checking for gas leaks in the system insulate the pipe hose and cables Then place the indoor unit on the installation plate 1 To avoid condensation problems place heat resistant polyethylene foam separately around
26. ature while saving energy and having sound sleep For easy future reference write the model and serial Model number down You will find your model number on the a right side of the air conditioner Serial Neo Forte ND IB E 32582 1 indd 2 2011 06 15 m 6 06 10 Contents SATETY DKECAUITIONS E A E O A NAO A A AA A A 4 m Viewing your air conditioner NGA AA AA AA 8 2 Checking the indoor unit and display s 2ssisesenrsennnnunenisniinnlonindasbatininanainininmauniimanniaidonunnan 8 o Removing the front aNG KNADAGAPINIANAG GAGANA AAP IGANKAGGAAAA 9 Checking PUTAK Te eL AA PN 10 Operating basic FUNCTION c ssscsssssssscssscsnscsssssssscsnscsssssssscsnscessccsssconscsnscssssconscenscessscunscenscsssscunscssscsssscsnscssscessceass 12 TURNING the air conditioner GM and OM sanasen RNANA 12 Selecting operation MOCE smipioioininimi a 12 Adjusting theair flow direction soctusretucssorusonnssconsnstntexacocoestonssueSeuavasbivicsSooeonbatbuncsassestvarivectotSsonrlessoics GALA AN 17 Using advanced functions s sssscsssccssssnsscsssssnscenscenssconscenscenscessscenscenscessscenscenscessscenscenscensccssscenscenscsssscenscanscssssess 18 Using the WGO TMI UI IE saiia costo anes oustaatib sia ete aud weer naeaeteiataniata 18 En NG UNG maa NAN NAA ANAN 19 Cleaning and maintaining the air conditioner sssssesssesssscsessssssnsconscsnscssscnsssnssesscsssssssssssssscssscsssesssenscensees 24 NG AA CITON maneni iaaa 24 Jenno AS TUES seas anv
27. check the following Theappropriate indicator lights up and the air conditioner oper ates according to the selected mode or function 4 Press the ae button and check the following The airflow blades work properly 46 Neo Forte ND IB E 32582 1 indd 46 good sleep pi Off Timer 2011 06 15 m 6 08 14 Providing information for user After finishing the installation of the air conditioner you should explain the following to the user Refer to appropriate pages in the user amp installation manual 1 How to start and stop the air conditioner 2 Howto select the modes and functions HSITON3I 3 How to adjust the temperature and fan speed 4 How to adjust the airflow direction 5 Howto set the timers 6 How to clean and replace the filters When you complete the installation successfully hand over the user amp installation manual to the user for storage in a handy and safe place 47 Neo Forte ND IB E 32582 1 indd 47 2011 06 15 m 6 08 14 Samsunga QUESTIONS OR COMMENTS COUNTRY CALL OR VISIT US ONLINE AT ARGENTINE 0800 333 3733 www samsung com BRAZIL Wi aan www samsung com CHILE 800 SAMSUNG 726 7864 www samsung com COLOMBIA 01 8000112112 www samsung com COSTA RICA 0 800 507 7267 www samsung com DOMINICA 1 800 751 2676 www samsung com ECUADOR 1 800 10 7267 www samsung com EL SALVADOR 800 6225 www samsung com GUATEMALA 1
28. d power is exceeded over 10 of supply rating the indoor unit is protected stopped and the error mode indicates To protect the product from water and possible shock you should keep the power cable and the connection cord of the indoor and outdoor units in the iron pipe Connect the power cable to the auxiliary circuit breaker An all pole disconnection from the power supply must be incorporated in the fixed wiring 3mm You must keep the cable in a protection tube Keep distances of 50mm or more between power cable and communication cable Maximum length of power cables are decided within 10 of power drop If it exceeds you must consider another power supplying method The circuit breaker ELCB or MCCB ELB should be considered more capacity if many indoor units are connected from one breaker Use round pressure terminal for connections to the power terminal block For wiring use the designated power cable and connect it firmly then secure to prevent outside pressure being exerted on the terminal board Use an appropriate screwdriver for tightening the terminal screws A screwdriver with a small head will strip the head and make proper tightening impossible Over tightening the terminal screws may break them See the table below for tightening torque for the terminal screws o 0 0 88 Tightening torque kgf cm 42 Neo Forte_ND _IB_E 32582 1 indd 42 2011 06 15 m 6 08 10 Assigning address
29. difference of both indoor and outdoor units as indicated in the installation diagram Wall that prevents vibration and is strong enough to hold the product weight Out of the direct sunlight 1m or more away from the TV or radio to prevent the screen from being distorted or noise from being generated As far away as possible from fluorescent and incandescent lights so that the remote control can be operated well A place where the air filter can be replaced easily HSITDNA CAUTION Avoid the following places to prevent malfunction of the unit Where there is machine oil Salty environment such as the seaside areas Where sulfide gas exists Other special atmosphere areas Observe the clearances and maximum lengths as seen in the picture below when installing the air conditioner 300 mm or more Wrap the refrigerant pipes and the drain hose with the absorbent pad and vinyl tape Refer to page 49 for further details 34 The appearance of the unit may be different from the diagram depending on the model 33 Neo Forte ND IB E 32582 1 indd 33 2011 06 15 m 6 06 55 Accessories The following accessories are supplied with the air conditioner gt The number of each accessory is indicated in parentheses Accessories in the Indoor Unit Case Installation Plate Remote Control Batteries for User amp Installation Remote Control Manual NY 1 29 GS D D 34 Neo Forte_
30. e ND IB E 32582 1 indd 17 2011 06 15 m 6 06 35 Using advanced functions USING THE TURBO FUNCTION Turbo function will be helpful to cool or heat your room quickly and effectively by operating at the maximum fan speed for 30 minutes 1 Turn on the air conditioner Press the Power N amp Set Cancel button on the remote control 2 Set the operating mode Press the Turbo button on the remote control until Turbo indicator appears on the remote control display The air conditioner operates in Turbo fan speed and automatically adjusts the temperature according to the current room temperature The unit operates for 30 minutes and then operates in last used mode or in Auto mode if Dry Fan mode is most recent mode used 4 Turbo function is only available in Auto Cool Heat mode If Turbo function is selected in Dry Fan mode operating mode changes to Auto To deactivate Turbo function 1 Press the Turbo button on the remote control again The air conditioner operates in last used mode or in Auto mode if Dry Fan mode is most recent mode used K e When you are using the remote control make sure corresponding indicator appears on the remote control display e Temperature Fan speed cannot be adjusted while using this function e Air flow can be adjusted manually See page 17 for instructions e When the Turbo function is activated pressing Mode button will automatically cancel the function 18 Neo Forte_ND
31. e changes in good sleep mode To prevent excessive cooling heating during sleep the good sleep mode automatically modifies the temperature setting in accordance with the time setting Temperature and air current change according to the three stages Fall asleep Sound sleep and Wake up from good sleep mode and then the air conditioner will automatically turn off when the set time has elapsed HSITDNA Three stage good sleep prevents you from having difficulty sleeping in summer winter night Fall asleep Eases you into sleep by dropping the temperature Sound sleep Relaxes your body and raises your temperature slightly Wake up from good sleep mode Allows you to wake up from comfortable intermittent air and it makes you feel refresh iY Set Off timer in good sleep mode over 5 hours You feel disturbed sleep if the good sleep is set too short or long because the default is set to 8 hour operation If the good sleep mode is set less than 4 hours the operation will stop at the set time If the good sleep mode is set over 5 hours it will run as Wake up stage for the last one hour before stop e Recommended set temperature is between 25 C 27 C for cooling and 21 C 23 C for heating To deactivate good sleep mode 1 Press the Power O 8 Set Cancel button on the remote control good sleep mode you set will be canceled and good sleep indicator will disappear 23 Neo Forte ND IB
32. e the panel HSITON3I SLL LTT SS ee TITI Power button and Room temperature sensor You may locate the Power button on the right bottom side of the air conditioner If the front panel is open you can check the room temperature sensor You can turn on the air conditioner without the remote control by pressing the Power button The room temperature sensor measures indoor room temperature Power 1 button Neo Forte ND IB E 32582 1 indd 9 2011 06 15 m 6 06 17 Viewing your air conditioner CHECKING THE REMOTE CONTROL You can activate the air conditioner by pointing the remote control away from it When using the remote control always point it directly at the air conditioner Remote control display Mode Set one of the 5 operating modes See pages 12 16 for instructions Turbo Operate in maximum fan speed to cool warm quickly Air swing Activate Deactivate air flow blade movement automatically up and down good sleep Set the good sleep mode on off IZ 10 Neo Forte ND IB E 32582 1 indd 10 as bm i An Pr ey sep On J5 Off Timer i Set good sleep way TI aeea AV He the temperature by 1 C Fan speed ch Adjust how much air flows through the air conditioner with the 4 different fan speeds such as Auto Low Medium High On timer Set the on timer on Adjust the time for On time
33. each refrigerant pipe in the lower part of the indoor unit 2 Wrap the refrigerant pipe and the drain hose in the rear of the indoor unit with the absorbent pad gt Wind the pipe and hose three times to the end of the indoor unit with the absorbent pad 20 mm interval 3 Wind the pipe assembly cable and drain hose with insulation tape 4 Place the bundle the pipe assembly cable and drain hose in the lower part of the indoor unit carefully so it doesn t project from the rear of the indoor unit Installation plate 5 Hook the indoor unit to the installation plate and move the unit to the right and left until it is securely in place AE ZIA TILA LS 6 Wrap the rest of the pipe with vinyl tape 7 Attach the pipe to the wall using clamps optional 45 Neo Forte ND IB E 32582 1 indd 45 2011 06 15 m 6 08 13 Final check and trial operation To complete the installation perform the following checks and tests to ensure that the air conditioner operates correctly 1 Check the following Strength of the installation site Tightness of pipe connection to detect gas leak Electric wiring connection Heat resistant insulation of the pipe Drainage Grounding conductor connection Correct operation follow the steps below 000008 2 Press the button and check the following The indicator on the indoor unit lights up The airflow blade opens and the fan gears up for operation 3 Press any button and
34. ece on the rear of the indoor unit unless you connect the pipe directly from the rear 2 Smooth the cut edges 3 Remove the protection caps of the pipes and connect the assembly pipe to each pipe Tighten the nuts first with your hands and then Refrigerant oil with a torque wrench applying the following torque Se Outer Diameter Torque kgfecm 6 35 mm 1 4 145 175 BA 9 52 mm 3 8 333 407 12 70 mm 1 2 505 615 Torque wrench 15 88 mm 5 8 630 769 q Spanner gt Ifyou want to shorten or extend pipes refer to page 41 Flare nut Union 4 Cutoff the remaining foam insulation 5 If necessary bend the pipe to fit along the bottom of the indoor unit Then pull it out through the appropriate hole The pipe should not project from the rear of the indoor unit The bending radius should be 100 mm or more 6 Pass the pipe through the hole in the wall 7 For further details on how to connect to the outdoor unit and purge the air refer to page 35 gt The pipe will be insulated and fixed permanently into position after finishing the installation and the gas leak test refer to page 49 for further details gt DO NOT WALL UP THE PIPE CONNECTION Allrefrigerant pipe connection must be easy accessible and serviceable 36 Neo Forte_ND _IB_E 32582 1 indd 36 2011 06 15 m 6 07 06 Cutting or extending the pipe 1 Make sure that you prepared the required tools pipe cutter reamer flaring tool and pipe holder 2
35. fer to the table for efficient use OPERATIONAL TEMPERATURE INDOOR MODE HUMIDITY IF OUT OF CONDITIONS INDOOR OUTDOOR Condensation may occur on the a ONE COOLING 18 C to 32 C 5 C to 43 C 80 indoor unit with risk to have either or less water blow off or drops on the floor HEATING 27 C or less 20 C to 24 C g Internal protection triggers and the air conditioner will stop Condensation may occur on the DRYING 18 C to 32 C 5 C to 43 C g indoor unit with risk to have either water blow off or drops on the floor iY The standardized temperature for heating is 7 C If the outdoor temperature drops to 0 C or below the heating capacity can be reduced depending on the temperature condition If the cooling operation is used at over 32 C indoor temperature it does not cool at its full capacity 30 Neo Forte ND IB E 32582 1 indd 30 2011 06 15 00 6 06 51 Safety precautions Carefully follow the precautions listed below because they are essential to guarantee the safety of the equipment A WARNING Always disconnect the air conditioner from the power supply before servicing it or accessing its internal components e Verify that installation and testing operations are performed by qualified personnel e Verify that the air conditioner is not installed in an easily accessible area HSITONA GENERAL INFORMATION Carefully read the content of this manual before installing the air condit
36. g energy and having sound sleep good sleep mode can be set up when the air conditioner is on 1 Set the operating mode Press the Mode button on the remote control until Cool Heat appears on the remote control display IZ good sleep is only available in Cool Heat mode 2 Press the good sleep button on the remote control good sleep indicator and Off timer indicator appear on the remote control display Default good sleep time is set to 8 hours Press good sleep button on the remote control to change the time setting while Off timer indicator is blinking good sleep You can set the time up to 12 hours increasing in 30 minute unit up to first 3 hours and in hourly unit K Ca after first 3 hours q 7 4 Press the Power O 8 Set Cancel button on the remote control to active it on The remote control display will show the hour s you have set When the set time has elapsed the air conditioner will automatically turn off and then good sleep indicator disappears If good sleep mode is not set within 10 seconds the air conditioner will end setting f Timer 4 e Temperature Fan speed Air swing can be adjusted after setting good sleep in Heat mode e Temperature can be adjusted and the air conditioner automatically adjusts the Fan speed Air swing after setting good sleep in Cool mode 22 Neo Forte ND IB E 32582 1 indd 22 2011 06 15 m 6 06 44 Temperatur
37. he air conditioner will operate in the mode you set KK On timer function is available in Auto Cool Dry Fan Heat mode 4 e Temperature can also be adjusted See step 3 on page 13 for instructions e After the set up while the unit is off approximately after 10 seconds all the other indicators will be gone except the On timer indicator and remaining time e Setting time allows you to change by pressing the On Timer button Press the On Timer button to change time setting and then press the Power O 8 Set Cancel button to active iton To deactivate the On timer 1 Press the Power D amp Set Cancel button on the remote control On timer you set will be canceled and On timer indicator will disappear 19 Neo Forte_ND _IB_E 32582 1 indd 19 2011 06 15 m 6 06 39 Using advanced functions SETTING THE TIMER Off timer This function allows you to turn off the air conditioner automatically within the time range of 24 hours Off timer is functional when the unit is operating 1 Press the Off Timer button on the remote control Off timer indicator blinks on the remote control display 2 Set the time you want the air conditioner to turn off automatically Press the Off Timer button on the remote control to change the time setting while Off timer indicator is blinking You can set the time up to 24 hours increasing in 30 minute unit up to first 3 hours and in hourly unit after first 3 hours 3
38. installed electric shock or fire may occur Make sure that the condensed water dripping from the drain hose runs out properly and safely Install the power cable and communication cable of the indoor and outdoor unit at least 1m away from the electric appliance Install the indoor unit away from lighting apparatus using the ballast If you use the wireless remote control reception error may occur due to the ballast of the lighting apparatus Do not install the air conditioner in following places Place where there is mineral oil or arsenic acid Resin parts flame and the accessories may drop or water may leak The capacity of the heat exchanger may reduce or the air conditioner may be out of order The place where corrosive gas such as sulfurous acid gas generates from the vent pipe or air outlet The copper pipe or connection pipe may corrode and refrigerant may leak The place where there is a machine that generates electromagnetic waves The air conditioner may not operate normally due to control system The place where there is a danger of existing combustible gas carbon fiber or flammable dust The place where thinner or gasoline is handled Gas may leak and it may cause fire 32 Neo Forte ND IB E 32582 1 indd 32 2011 06 15 m 6 06 52 Choosing the installation location Where airflow is not blocked Where cool air can be distributed throughout the room Install the refrigerant piping length and the height
39. ion properly 11 Neo Forte ND IB E 32582 1 indd 11 2011 06 15 m 6 06 26 Operating basic function TURNING THE AIR CONDITIONER ON AND OFF Press the Power O 8 Set Cancel button on the remote control NI You will hear a ringing sound and the air flow blade will Off Timer move up and down automatically when the air conditioner is gt properly on The air conditioner will operate in the most recent operation mode used or Auto mode t cel When you turn off the air conditioner air flow blade will stop NT i moving and remain closed Se Can a IZ Turning on off your air conditioner without the remote control You can operate your air conditioner by pressing the Power button on the right bottom side of the air conditioner SELECTING OPERATION MODE Auto In Auto mode the air conditioner will automatically set the temperature and fan speed depending on the room temperature detected by the room temperature sensor 1 Turn on the air conditioner Press the Power O 8 Set Cancel button on the remote control 2 Set the operating mode Press the Mode button on the remote control until Auto mode and Auto fan speed indicator appear on the remote control display The air conditioner will automatically set the operation mode to Cool or Heat depends on the room temperature Z When you press the Mode button mode will change in order of Auto Cool Dry Fan and Heat 3 Set the Tempera
40. ioner and store the manual in a safe place in order to be able to use it as reference after installation For maximum safety installers should always carefully read the following warnings Store the operation and installation manual in a safe location and remember to hand it over to the new owner if the air conditioner is sold or transferred This manual explains how to install an indoor unit with a split system with two SAMSUNG units The use of other types of units with different control systems may damage the units and invalidate the warranty The manufacturer shall not be responsible for damages arising from the use of non compliant units The air conditioner is compliant with the requirements of the Low Voltage Directive 72 23 EEC the EMC Directive 89 336 EEC and the Directive on pressurized equipment 97 23 EEC The manufacturer shall not be responsible for damage originating from unauthorized changes or the improper connection of electric and hydraulic lines Failure to comply with these instructions or to comply with the requirements set forth in the Operating limits table included in the manual shall immediately invalidate the warranty The air conditioner should be used only for the applications for which it has been designed the indoor unit is not suitable to be installed in areas used for laundry Do not use the units if damaged If problems occur switch the unit off and disconnect it from the power supp
41. led in the wall check the following 0 0 0 1 5cm l less IE 0 Ditch The hose must The end of the drain Do NOT bendthehose Keep a clearance of at Do NOT place the end NOT slant upwards hose must NOT be in different directions least 5cm between the of the drain hose in a placed under water end of the hose and the hollow ground Drain hose installation 1 If necessary connect the 2 meter extension drain hose to the Shield drain hose a THIN El TE 2 Ifyou use the extension drain hose insulate the inside of the 2 N f Drain hose Extension drain hose extension drain hose with a shield 3 Fitthedrain hose into 1 of 2 drain hose holes then fix the end of the drain hose tightly with a clamp gt Ifyou don t use the other drain hose hole block it with a rubber stopper 4 Pass the drain hose under the refrigerant pipe keeping the drain hose tight 5 Pass the drain hose through the hole in the wall Check if it slants downwards as seen in the picture gt The hose will be fixed permanently into position after finishing the installation and the gas leak test refer to page 49 for further details gt DONOT WALL UP THE DRAIN HOSE CONNECTION Drain hose connection must be easy accessible and serviceable 38 Neo Forte_ND _IB_E 32582 1 indd 38 2011 06 15 m 6 07 11 Changing direction of the drain hose You can select the direction of the drain hose depending
42. ler and do not disassemble the remote controller Do not touch the pipes connected with the product gt This may result in burns or injury Do not use this air conditioner to preserve precision equipment food animals plants or cosmetics or for any other unusual purposes gt This may result in property damage HSITONA Avoid directly exposing humans animals or plants from the air flow from the air conditioner for long periods of time gt This may result in harm to humans animals or plants This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance FOR CLEANING WARNING O Do not clean the appliance by spraying water directly onto it Do not use benzene thinner alcohol or acetone to clean the appliance gt This may result in discoloration deformation damage electric shock or fire Before cleaning or performing maintenance unplug the air conditioner from the wall socket and wait until the fan stops gt Failing to do so may result in electric shock or fire FOR CLEANING NCAUTION O Take care when cleaning the surface of the heat exchanger of the outdoor unit since it has sharp edges gt To avoid cutting y
43. ly In order to prevent electric shocks fires or injuries always stop the unit disable the protection switch and contact SAMSUNG technical support if the unit produces smoke if the power cable is hot or damaged or if the unit is very noisy Always remember to inspect the unit electric connections refrigerant tubes and protections regularly These operations should be performed by qualified personnel only The unit contains moving parts which should always be kept out of the reach of children Do not attempt to repair move alter or reinstall the unit If performed by unauthorized personnel these operations may cause electric shocks or fires Do not place containers with liquids or other objects on the unit All the materials used for the manufacture and packaging of the air conditioner are recyclable The packing material and exhaust batteries of the remote control optional must be disposed of in accordance with current laws The air conditioner contains a refrigerant that has to be disposed of as special waste At the end of its life cycle the air conditioner must be disposed of in authorized centers or returned to the retailer so that it can be disposed of correctly and safely INSTALLING THE UNIT IMPORTANT When installing the unit always remember to connect first the refrigerant tubes then the electrical lines Always disassemble the electric lines before the refrigerant tubes Upon receipt inspect the
44. n order of Auto Cool Dry Fan and Heat 3 Set the temperature Press the Temperature A or V button on the remote control to increase or decrease the desired temperature You can set the desired temperature between the range of 18 C 30 C as WY Turbo CT J Z You can increase decrease the temperature by 1 C KK e When you are using the remote control make sure correct indicator which matches your selection appears on the remote control display e Air flow can be adjusted manually See page 17 for instructions 14 Neo Forte ND IB E 32582 1 indd 14 2011 06 15 m 6 06 31 Fan Fan mode can be selected to ventilate your room Fan mode will be helpful to refresh the stale air in your room 1 Turn on the air conditioner HSITON3I Press the Power O amp Set Cancel button on the remote control 2 Set the operating mode Press the Mode button on the remote control until Fan mode indicator appears on the remote control display The air conditioner operates in Fan mode and automatically adjusts the temperature according to the current room temperature KK When you press the Mode button mode will change in order of Auto Cool Dry Fan and Heat 3 Set the fan speed Press the Fan Speed button on the remote control to set the desired fan speed GOCE P F W5 8 CD KK When you press the Fan Speed Shy button fan speed will change in order of Aut
45. o Low Medium and High SZ e When you are using the remote control make sure correct indicator which matches your selection appears on the remote control display e Air flow can be adjusted manually See page 17 for instructions 15 Neo Forte ND IB E 32582 1 indd 15 2011 06 15 m 6 06 32 Operating basic function SELECTING OPERATION MODE 16 Heat The air conditioner heats as well as cools Warm your room with this versatile appliance in the cold of winter 1 Turn on the air conditioner Press the Power O 8 Set Cancel button on the remote control 2 Set the operating mode Press the Mode button on the remote control until Heat mode indicator appears on the remote control display The air conditioner operates in Heat mode and warms your room iY When you press the Mode button mode will change in order of Auto Cool Dry Fan and Heat 3 Set the temperature Press the Temperature A or V button on the remote control to increase or decrease the desired temperature You can set the desired temperature between the range of 16 C 30 C KK You can increase decrease the temperature by 1 C 4 Set the fan speed Press the Fan Speed y button on the remote control to set the desired fan speed If room temperature reaches desired value heating will stop for a while K e When you press the Fan Speed Shy button fan speed will change in order of Auto Low Medium and High
46. on where you want to install the indoor unit 1 Detach the rubber cap with the flyer 2 Detach the drain hose by pulling it and turning to the left 3 Insert the drain hose by fixing it into the groove of the drain hose and the outlet of the drain pan 4 Attach the rubber cap with a screwdriver by turning it to the right until it fixes to the end of the groove Neo Forte ND IB E 32582 1 indd 39 HSITON3I 39 2011 06 15 m 6 07 13 Wiring work Power and communication cable connection 1 Before wiring work you must turn off all power source 2 Indoor unit power should be supplied through the breaker ELCB or MCCB ELB separated by the outdoor power ELCB Earth Leakage Circuit Breaker MCCB Molded Case Circuit Breaker ELB Earth Leakage Breaker 3 The power cable should be used only copper wires 4 Connect the power cable 1 L 2 cable F1 F2 each N among the units within maximum length and communication 5 Connect V1 V2 for DC12V and F3 F4 for communication when installing the wired remote control Outdoor Unit 208 Ko ELCB a Ca K 7 rt 2 N F1 F2 1 L a F1 Wired Remote Control 4 Z VV TV F2 1 L 2 N
47. our fingers wear thick cotton gloves when cleaning it O Do not clean the inside of the air conditioner by yourself b For cleaning inside the appliance contact your nearest service center gt When cleaning the internal filter refer to the descriptions in the Cleaning and maintaining the air conditioner section gt Failure to do may result in damage electric shock or fire Neo Forte_ND _IB_E 32582 1 indd 7 2011 06 15 m 6 06 11 Viewing your air conditioner Congratulations on the purchase of the air conditioner We hope you enjoy the features of your air conditioner and stay cool or warm with optimal efficiency Please read the user manual to get started and to make the best use of the air conditioner CHECKING THE INDOOR UNIT AND DISPLAY Carefully unpack your air conditioner and check the unit to make sure it is not damaged Main parts Air filter under the panel C Air intake lt VSS N ae eee E Air flow blade XX i Blade pin lever Air flow blade Power l button Display Operation indicator r F mzLa Timer indicator _ AF Turbo indicator at 4 Your air conditioner may slightly look different from illustration shown above depending on your model Neo Forte_ND _IB_E 32582 1 indd 8 2011 06 15 m 6 06 14 REMOVING THE FRONT PANEL Tightly grab both side of the front panel and lift up the panel to open Then slide the panel towards to remov
48. product to verify that it has not been damaged during transport If the product appears damaged DO NOT INSTALL it and immediately report the damage to the carrier or retailer if the installer or the authorized technician has collected the material from the retailer After completing the installation always carry out a functional test and provide the instructions on how to operate the air conditioner to the user Do not use the air conditioner in environments with hazardous substances or close to equipment that release free flames to avoid the occurrence of fires explosions or injuries 31 Neo Forte ND IB E 32582 1 indd 31 2011 06 15 m 6 06 52 Safety precautions To prevent injury when accidentally touching the indoor unit fan install the indoor unit at least 2 5m above the floor The air conditioner should be used only for the applications for which it has been designed the indoor unit is not suitable to be installed in areas used for laundry Our units must be installed in compliance with the spaces indicated in the installation manual to ensure either accessibility from both sides or ability to perform routine maintenance and repairs The units components must be accessible and that can be disassembled in conditions of complete safety either for people or things For this reason where it is not observed as indicated into the Installation Manual the cost necessary to reach and repair the unit in safety as required by current
49. pt to repair disassemble or modify the appliance yourself gt Do not use any fuse such as cooper steel wire etc other than the standard fuse gt Failing to do so may result in electric shock fire problems with the product or injury FOR USING CAUTION O Do not place objects or devices under the indoor unit gt Water dripping from the indoor unit may result in fire or property damage Check that the installation frame of the outdoor unit is not broken at least once a year gt Failing to do so may result in injury death or property damage Max current is measured according to IEC standard for safety and current is measured according to ISO standard for energy efficiency O Do not stand on top of the appliance or place objects such as laundry lighted candles lighted cigarettes dishes chemicals metal objects etc on the appliance gt This may result in electric shock fire problems with the product or injury Do not operate the appliance with wet hands gt This may result in electric shock Do not spray volatile material such as insecticide onto the surface of the appliance gt As well as being harmful to humans it may also result in electric shock fire or problems with the product Do not drink the water from the air conditioner gt The water may be harmful to humans Neo Forte ND IB E 32582 1 indd 6 2011 06 15 m 6 06 11 FOR USING A CAUTION S Do not apply a strong impact to the remote control
50. r Off timer Set the off timer on Adjust the time for Off timer Power amp Set Cancel Turn on off the air conditioner and set cancel the timer function Each time you press the button a short beep will sound and a transmit indicator appears on the remote control display 2011 06 15 Remote control display Transmit indicator HA Lai Operation mode indicator CeO Br Auto z OO Na Ta CH Dry A Set temperature indicator i lt a 9 Fan Ja 3 EEN AE Q Heat J z Turbo indicator good sleep indicator Fan speed indicator ofl Auto ols Low SA Medium Sanh High gt al Turbo LUH aaa Low battery indicator Using the remote control e Point the remote control towards the remote control sensor of the unit e When properly pressing the button on the remote control you will hear beep sound from the unit fH e The signal may not be received well of electronic lighting style fluorescent lamps such as inverter fluorescent lamps are in the same space e f other electrical products operate by the remote control call your nearest contact center Installing the batteries 1 Slide the cover onthe rear side 2 Install two AAA batteries 3 Close the cover by sliding it back of the remote control down to Gama abra NANALONG AO to its original position open signs accordingly Make sure you You should hear click sound have installed the batteries in when the cover is locked correct posit
51. range of 16 C 30 C K You can increase decrease the temperature by 1 C 4 Set the fan speed Press the Fan Speed button on the remote control to set the desired fan speed If room temperature reaches desired value the air conditioner will shut off cooling for a while and just the fan runs 4 When you press the Fan Speed Shy button fan speed will change in order of Auto Low Medium and High e When you are using the remote control make sure correct indicator which matches your selection appears on the remote control display e Air flow can be adjusted manually See page 17 for instructions e If current outside temperatures are much higher than the selected indoor temperature it may take time to bring the inner temperature to the desired coolness 13 Neo Forte ND IB E 32582 1 indd 13 2011 06 15 m 6 06 30 Operating basic function SELECTING OPERATION MODE Dry The air conditioner in Dry mode acts like a dehumidifier by removing moisture from the indoor air Dry mode makes the air feel refreshing in a humid climate 1 Turn on the air conditioner Press the Power O 8 Set Cancel button on the remote control 2 Set the operating mode Press the Mode button on the remote control until Dry mode indicator appears on the remote control display The air conditioner operates in Dry mode and automatically adjusts the fan speed to Auto K When you press the Mode button mode will change i
52. t turn the air conditioner off with the circuit breaker while it is operating gt Turning the air conditioner off and then on again with the circuit breaker may cause a spark and rsult in electric shock or fire After unpacking the air conditioner keep all packaging materials well out of the reach of children as packaging materials can be dangerous to children gt If a child places a bag over its head it may result in suffocation Do not insert your fingers or foreign substances into the outlet when the air conditioner is operating gt Take special care that children do not injure themselves by inserting their fingers into the product Do not touch the air flow blade with your hands or fingers during the heating operation gt This may result in electric shock or burns Do not insert your fingers or foreign substances into the air inlet outlet of the air conditioner gt Take special care that children do not injure themselves by inserting their fingers into the product Do not use this air conditioner for long periods of time in badly ventilated locations or near infirm people gt Since this may be dangerous due to a lack of oxygen Open a window at least once an hour If any foreign substance such as water has entered the appliance cut the power by unplugging the power plug and turning the circuit breaker off and then contact your nearest service center gt Failing to do so may result in electric shock or fire Q Do not attem
53. the product Neo Forte ND IB E 32582 1 indd 4 2011 06 15 m 6 06 11 FOR INSTALLATION CAUTION GD Install the draining hose properly so that water is drained correctly gt Failing to do so may result in water overflowing and property damage When installing the outdoor unit make sure to connect the draining hose so that draining is performed correctly gt The water generated during the heating operation by the outdoor unit may overflow and result in property damage In particular in winter if a block of ice falls it may result in injury death or property damage HSITDNA FOR POWER SUPPLY WARNING Q When the circuit breaker is damaged contact your nearest service center O Do not pull or excessively bend the power line Do not twist or tie the power line Do not hook the power line over a metal object place a heavy object on the power line insert the power line between objects or push the power line into the space behind the appliance gt This may result in electric shock or fire FOR POWER SUPPLY NCAUTION When not using the air conditioner for a long period of time or during a thunder lightning storm cut the power at the circuit breaker gt Failing to do so may result in electric shock or fire FOR USING A WARNING If the appliance is flooded please contact your nearest service center gt Failing to do so may result in electric shock or fire If the appliance generates a strange noise a burning
54. ture Press the Temperature A or V button on the remote control to increase or decrease the desired temperature You can set the desired temperature between the range of 16 C 30 C sa You can increase decrease the temperature by 1G YH e When the air conditioner is already operating in another mode press the Mode button until Auto mode indicator appears on the remote control display e When you are using the remote control make sure correct indicator which matches your selection appears on the remote control display e Air flow can be adjusted manually See page 17 for instructions 12 Neo Forte_ND _IB_E 32582 1 indd 12 2011 06 15 m 6 06 28 Cool In Cool mode the air conditioner will cool your room You can adjust the temperature and the fan speed to feel cooler in hot season 1 Turn on the air conditioner HSITON3I Press the Power O amp Set Cancel button on the remote control 2 Set the operating mode Press the Mode button on the remote control until Cool mode indicator appears on the remote control display The air conditioner operates in Cool mode and will lower the temperature in your room KK When you press the Mode button mode will change in order of Auto Cool Dry Fan and Heat 3 Set the temperature Ki Press the Temperature A or V button on the remote control to increase or decrease the desired temperature You can set the desired temperature between the
Download Pdf Manuals
Related Search