Samsung SU3360 מדריך למשתמש
Contents
1. Do not use with any opening blocked keep openings free of dust lint hair and anything that may reduce air flow e Keep hair loose clothing fingers and all parts of body away from openings and moving parts e Do not pick up anything that is burning or smoking such as cigarettes matches or hot ashes e Do not use without dirt cup or filters in place Empty dirt cup and clean filter frequently when picking up very fine materials such as powder e Turn off all controls before unplugging vacuum cleaner e Use extra care when cleaning on stairs e Do not use to pick up flammable or combustible materials such as gasoline or fine wood fine wood sandings or use in areas where they may be present e Store your vacuum cleaner indoors in a cool and dry area e Avoid picking up hard sharp objects with the cleaner They may damage the cleaner e Always turn off this appliance before connecting or disconnecting the hose removing the bottom plate for maintenance e Use only on dry indoor surfaces never change the plug in any way e Do not modify the polarized plug to fit a non polarized outlet or extension cord e Do not touch the brush roller when it is rotating e Keep suction away from your face when using nozzles and pipe e Do not pull the power cord around sharp corners and do not allow it to be trapped e Unplug before connecting turbine nozzle only using turbine brush model This appliance is not intended for use by persons includi2. Filter gt Select Models Only a lt Hepa Media Filter gt Select Models Only 1 Unplug the Vacuum Cleaner from electrical outlet 2 The Post Motor Filter assists in the filtration process to return clean air to the room It is located behind the door on the front of the Cleaner When the filter becomes dirty open the door remove the filter and replace Note The Post Motor Filter is a white pleated HEPA media filter This filter is not washable and must be replaced when it becomes dirty maintenance _9 AONVNALNIVIN 0 Maintenance CHECK ROTATING BRUSH AND DRIVE BELT You should check your vacuum cleaner s Rotating Floor Brush and Drive Belt regularly for wear or damage You A WARNING should also clean the brush and brush ends of strings e hair and carpet fibers These can wrap around the oe eee a brush and hamper its ability to effectively clean your off vacuum cleaner and carpet Also remove any debris that has accumulated disconnect Power Plug from under the brush cover electrorical outlet Unplug the Vacuum Cleaner from electrical outlet Place handle in Low position and turn vacuum cleaner over so bottom side is up Remove the six screws as shown with screwdriver Lift the Brush Cover off Grasp Rotating Floor Brush at both ends and lift Clean strings hair and other debris from Rotating Floor brush paying particular attention to brush ends 6 Clean strin
3. Rotating Floor Brush jammed e Clog in vacuum e Dust Bin full e Dust Bin not installed properly e Filters are dirty e Mini Turbo Brush is clogged or debris is wrapped around the brush roll e Adjust Powerfoot to correct height setting e Firmly push Hose Wand onto the suction opening e Make sure Twist Snap Hose is snapped into locked position e Check Hose and replace if needed e Replace Drive Belt see pg 10 e Replace Brush e Remove brush and clean debris from brush ends e Clear clog see pg 8 9 e Empty Dust Bin e Position correctly and lock in place e Check Pre motor and Post motor filters e Maintaining Mini Turbo Brush see pg 11 Visible dirt escaping from cleaner e Dust Bin full e Filters missing or installed incorrectly e Dust Bin installed incorrectly e Empty Dust Bin e Check Pre motor and Post motor filters for correct installation e Pull out and re attach Dust Bin correctly Code No DJ68 O0000A REV 0 0
4. SU33 SERIES Before operating this unit please read the instructions carefully English For indoor use only imagine the possibilities Thank you for purchasing a Samsung product ee Safety information IMPORTANT SAFETY INSTRUCTIONS Thank you for purchasing a Samsung vacuum cleaner When using an electrical appliance basic precautions should always be followed including the following PLEASE READ ALL WARNINGS AND INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER WARNING To reduce the risk of fire electric shock or injury e Do not leave vacuum cleaner unattended when it is plugged in e Unplug from outlet when not in use and before servicing e Do not use outdoors or on wet surfaces e Do not allow children to operate vacuum cleaner or use as a toy e Close attention is necessary when used by or near children e Use only as described in this manual Use only manufacturer s recommended attachments e Do not use with damaged cord or plug e If vacuum cleaner is not working as it should or has been dropped damaged left outdoors or dropped into water return it to a service center e Do not pull or carry by cord use cord as a handle close a door on cord or pull the cord around sharp edges or corners Keep cord away from heated surfaces e Do not unplug by pulling on the cord To unplug grasp the plug not the cord e Do not handle vacuum cleaner or plug with wet hands e Do not put any object into openings
5. action for small areas such as stairs and upholstery Note Press gently when using Mini Turbo Brush to gain maximum cleaning Too much pressure could cause the brush to stop rotating POWER CORD STORAGE 1 To use your vacuum remove the cord and plug it into an electrical outlet For your convenience there is a quick release cord wrap for easy cord removal When you are finished cleaning turn vacuum cleaner off Unplug power cord by grasping the polarized plug NOT the cord and disconnect from outlet Loop power cord around cord wraps on the back of the vacuum as shown Clip molded plug to power cord to secure ok ON operating the cleaner _7 MVaintenance To maintain maximum cleaning performance the following maintenance steps must be performed 1 Empty the Dust Bin when the dirt reaches the MAX A WARNING line on the side To reduce the risk of electronic 2 Cleaning the Grille Cyclone when the Dust Bin shock turn Power Switch OFF become clogged and disconnect polarized plug 3 Check the Pre Motor Filter at least once a month and ffrom electrical outlet before clean or replace as needed performing maintenance or 4 Replace the Post Motor Filter every three to six troubleshooting checks months Note More frequent filter cleaning or replacing may Tip be necessary if you are vacuuming new carpet p fine dust or have allergy concerns Follow the For maximum cleaning instru
6. bar including end plates and discard Inspect belt to ensure that it is in good condition If broken or cracked please replace See below for details With the curved ends facing down slide end plates of brushbar into slots on the tool To replace bottom plate insert the four tabs on edge of bottom plate into slots on front of tool Pivot bottom plate down and snap closed Ron AONVNALNIVIN 0 O oo Belt Replacement 1 Grasp turbine and pull firmly to remove 2 Remove a screw and lift the cover belt off 3 Remove belt from turbine pulley Replace with new belt 4 With flat sides of turbine retainers pointing down slide retainers into grooves in tool housing and snap into place 5 Replace brushbar and bottom plate Cleaning Brushbar e Cut off pet hairs or threads surrounding brush with scissors maintenance _ 11 troublesnocting Check this list of possible problems and solutions before bringing your vacuum to a service center PROBLEM possible solution Vacuum cleaner won t run e Power cord not plugged in e Blown fuse tripped breaker in home e Check electrical plug e Check Replace fuse or reset breaker Vacuum cleaner and tools won t pick up dirt e Incorrect Height Adjustment e Hose not attached to suction opening e Twist Snap Hose not securely attached e Crack or hole in Hose e Broken or worn Drive Belt e Rotating Floor Brush bristles worn e
7. ctions on the following pages to perform these simple maintenance steps performance check and clean or replace all filters as suggestsd EMPTY DUST BIN The Dust Bin needs to be emptied when the dirt reaches the MAX line on the side of it 1 Unplug cleaner from electrical outlet 2 To remove the Dust Bin from the vacuum body push the Dust Bin release button as shown 3 Hold dust bin and push down bin release empty button to empty dirt into garbage container as shown Note The Dust Bin may be washed in warmwater with a mild detergent Reassemble and makesure it is completely dry before using again CLEANING THE GRILLE If the suction is weak although the dust bin is empty open the cover and clean the Grille Grille Cyclone Note Whenever the Grille is clogged check the pre motor filter and clear it 8 maintenance Maintenance CLEANING THE PRE MOTOR FILTER Sponge PE Filter lt Washable gt 1 Unplug the Vacuum Cleaner from electrical outlet 2 The Pre Motor Filter Sponge Filter Micro Filter protects the motor from dirt particles It is located underneath the Dust Bin If the Pre Motor Filter becomes dirty remove and clean it Note The Pre Motor Filter may be hand washed in cold water with mild detergent Rinse well and air dry thoroughly before re installing REPLACING THE POST MOTOR FILTER TALE Post Motor Filter Option lt Micro
8. e as shown 5 Attach the Extension Wand and the Crevice Tool together into the holder on the right side of the body as shown 6 Attach the Combination Tool into the holder on the left side of the body as shown 7 Attach the Bracket Brush on the front of the handle and clip the Mini Turbo Brush into the Bracket Brush as shown assembling the cleaner _5 Ooerating the cleaner POWER SWITCH The Power Switch is located on the side of the vacuum Push the rocker switch ON to vacuum and OFF when cleaning is complete HANDLE POSITIONS Press the handle release pedal located on the lower left side of the vacuum with your foot to place your vacuum into one of three cleaning positions 1 Upright For storage and above floor cleaning with tools 2 Normal Cleaning Press handle release pedal once Position used for most household floor cleaning tasks 3 Low Cleaning With the vacuum in normal cleaning position press handle release pedal again Use for reaching under low furniture such as tables chairs or beds HEIGHT ADJUSTMENT The Powerfoot Rotating Floor Brush can be adjusted to clean several floor surfaces Note For optimal cleaning performance adjust to the lowest practical setting If your cleaner is difficult to push adjust to the next higher setting 1 Turn Height Adjustment Knob to desired setting Lowest Setting For bare floors Medium Settings For sho
9. gs hair and other debris from Motor Pulley and Drive Belt areas 7 Check Drive Belt carefully for wear cuts or stressed areas Motor 8 Check Air Passageway for obstructions Remove Pulley debris from this area NO OA WwW Air Passageway Replace Drive Belt 1 Unplug cleaner from electrical outlet 2 With Rotating Floor Brush removed from vacuum cleaner grasp old Drive Belt and remove from Motor Pulley Discard old Drive Belt 3 Place new Drive Belt over Motor Pulley and stretch other end over Rotating Floor Brush in the space between the bristles 4 Place ends of Rotating Floor Brush down into slots on sides as shown 5 Turn Rotating Floor Brush by hand several times in the direction of Motor Pulley If properly installed Drive Belt will center itself on Rotating Brush crown 6 Reposition Brush Cover and screws Insert the hook on the Brush Cover into the corresponding groove on the brush and tighten scerws securely Be careful of your hands when you replace the drive belt to avoide physical WARNING injury from sharp plastic film 10_ maintenance Maintenance MINI TURBO BRUSH Brushbar Replacement 1 Remove the tool from the hose and turn upside down Slide the switch to unlock position and remove bottom plate Unscrew the one screw and remove belt guard Remove brush
10. ng children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety e Children should be supervised to ensure that they do not play with the appliance e The plug must be removed from the socket outlet before cleaning or maintaining the appliance e f the supply cord is damaged it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard SAVE THESE INSTRUCTIONS This vacuum cleaner is intended for household use only FOR RESIDENTS OF THE UNITED KINGDOM ONLY If your appliance is fitted with a nonrewireable BS 1363 plug it must not be used unless a 13 amp ASTA approved to BS 1362 fuse is fitted in the carrier contained in the plug If for any reason the plug is cut off it must be disposed of as it is an electric shock hazard should it be inserted into a 13 amp socket 2_ safety information Safety Information SAFETY INFORMATION e Before operating the appliance please read this manual thoroughly and retain it warNinc for your reference e Because these following operating instructions cover various models the characteristics WARNING Of your vacuum Cleaner may differ slightly from those described in this manual CAUTION WARNING SYMBOLS USED WARNING Indicates that a danger of death or se
11. rious injury exists CAUTION Indicates that a risk of personal injury or material damage exists Contents ASSEMBLING THE CLEANER OPERATING THE CLEANER MAINTENANCE TROUBLESHOOTING Product View Attach Handle to Vacuum Attach Dust Bin to Vacuum Attach Vacuum Hose and Tools Power Switch Handle Positions Height Adjustment Transporting Cleaner Special On Board Tools Power Cord Storage Empty Dust Bin Cleaning the Grille Cleaning the Pre motor Filter Replacing the Post Motor Filter Check Rotating Brush and Drive Belt Mini Turbo Brush safety information _3 Assembling the cleaner PRODUCT VIEW i Handle f option Bracket Brush gt amp Cord Clip Select Models Only Wy option __ b Hose Clip Mini Turbo Brush 2 Quick Stretch Select Models Only 3 EA Hose Cord zZ 2 3 Wrap 2 Sits E ele Carrying 2 Power G Handle 3 Cord ET lt Extension I2 i Wand Power EZ A ce t Switch yclone z3 Dust Bin e Combination A Lower Cord Dusting Brush Wrap Upholstery Tool Post Motor Filter k j o Hose Post Motor Filter K Wand is located behind N the door erease Hose Pedal e Wand Base p CC XQ r Height Adjustment Knob Do not plug in your vacuum cleaner until you are familiar with all instruction
12. rt and medium pile carpets Highest Setting For plush pile carpet TRANSPORTING CLEANER 1 To move your cleaner from room to room put the Handle in the upright position tilt the cleaner back on its rear wheels and push forward 2 The cleaner can also be moved by using the Carrying Handle located on the top of the Dust Bin E Q 6_ operating the cleaner Operating the cleaner SPECIAL ON BOARD TOOLS Your vacuum is not only a powerful carpet and rug cleaner it s also a versatile above floor vacuum cleaner when you select one of the special tools 1 Raise Handle to Upright Position 2 Grasp the end of the Hose Wand and lift Hose Wand to separate from the Hose Wand Base 3 Attach tools by firmly pushing onto Vacuum Hose Quick Release o N O U m or Extension Wand Cord Wrap 5 Combination Dusting Brush Upholstery Tool Power Cord 5 Two Types of cleaning tools are included in one a T attachment rotate for desired tool gt e Extension m e Use Brush side to dust furniture blinds books c Wand O lamps shelves and baseboards Combination Z e Use Upholstery side for curtains draperies Dusting Brush 2 cushions fabrics Upholstery Tool m Hose Ba Crevice Tool aN Use in tight narrow spaces ae Extension Wand Use with desired attachment for a longer reach Mini Turbo Brush Select Models Use rotating brush
13. s caution and operating procedures AN Plastic film can be dangerous To avoid danger of suffocation keep away from waRNinc babies and children 4_ assembling the cleaner Assembling the cleaner ATTACH HANDLE TO VACUUM 1 Stand the vacuum upright and slide the base of the handle firmly into the grooves at the top of the vacuum body 2 Check to be sure the handle is fitted to the vacuum body If there is a gap continue to push firmly until the handle is flush 3 Insert the screw provided from the screw packet into the existing hole Tighten securely with a screwdriver ATTACH DUST BIN TO VACUUM Fit the groove located on the lower front side of the Dust Bin to the hook located on the vacuum body and attach the hook located on the Dust Bin Handle to the vacuum body as shown YANVATO AHL ONITEWASSV LO ATTACH VACUUM HOSE AND TOOLS 1 Attach the Twist Snap Hose by lining up the taps on the base with the corresponding notches on the back of the vacuum as shown 2 Turn the Twist Snap Hose clockwise to lock the hose into place 3 Grasping the Hose Wand slide the end of the it onto the Hose Wand Base Snap the Hose into the Hose Clip Ya Zao A a iy S Note The vacuum will not operate effectively unless the Hose Wand is firmly attached 4 Attach the Lower Cord Wrap by lining up the tab on the base with the corresponding notch on the back of the vacuum and turn it clockwis
Download Pdf Manuals
Related Search