Samsung AS36JAN User Manual
Contents
1. _ Bio Filter Deodorizing Filter There are Deodorizing and Bio filters inside your air conditioner They remove odors and dust in your room You should clean the filters every 3 months 1 Open the upper front grille by pulling the lower right and left tabs of the grille N Pull out the deodorizing and Bio filter 3 Wash the filters with clean water then dry them in the shade 4 Insert the filters in their place You can change the position of filters with each other 5 Close the front grille ELECTRONICS Contact SAMSUNG WORLD WIDE If you have any comments or questions regarding a Samsung product contact the SAMSUNG customer care center Country Customer Care Center 1 800 10 SAMSUNG 726 7864 1 800 3 SAMSUNG 726 7864 02 5805777 Web Site PHILIPPINES www samsung com ph Samsung Electronics Co Ltd All Rights Reserved HP USER S MANUAL AS30 Series AS32 Series AS36 Series Split type Air Conditioner Cooling DB98 30996A 22. The timer indicator stops blinking The selected mode and the temperature on the display disappear after 10 seconds The air conditioner turns on automatically at the appointed time and the On Timer setting disappears BATTERY D MODE 3 Press the button until the desired mode is displayed atthe top of theremote control to select the mode in advance Result The air conditioner operates in the selected mode when it is turned on If you don t use the remote control after setting the On Timer it turns off automatically after 25 hours To Cancel the On Timer SET CANCEL 1 Press the button to cancel the On Timer SETICANC Ifyou press the button both the On Timer and the Off Timer are canceled Setting the Off Timer You can set the Off Timer to turn off the air conditioner automatically at the appointed time You can set the time from 1 hour to 24 hours 1 Pressthe button until the required time is displayed to set the Off Timer You can set the time between 1 hour and 24 hours 2 Press the O Result ET CANCEL r button to complete the setting The remaining time is displayed The timer indicator stops blinking The air conditioner turns off automatically at the appointed time and the Off Timer setting disappears If you would like to turn the air conditioner on after 2 hours and to operate it for 2 hours 1 Press the button until 2 0 Hr
3. is displayed SET CANCEL 2 Press the O button 3 Press the button until 4 0 Hr is displayed 4 Press the button You can check or change the mode and or the temperature by pressing te button or the 7 A button after setting the Off Timer To Cancel the Off Timer SET CANCEL 5 1 Pressthe button to cancel the Off Timer If you press thO button both the On Timer and the Off Timer are canceled BATTERY BATTERY Setting the Sleep Timer You can set the Sleep Timer to turn off the air conditioner automatically while you are sleeping The air conditioner stops operating 6 hours after you set the Sleep Timer SLEEP 1 Press the button until the D indicator appears on the remote control Result The indoor unit beeps The air conditioner will be controlled as indicated in the illustrations below You can set Sleep Timer only in the Cool mode Cooling The set temperature is increased by 1 C every hour After the increase of 2 C the temperature is maintained for 4 hours To Cancel the Sleep Timer SLEEP 1 Press the button to cancel the Sleep Timer Result The indoor unit beeps The D indicator is no longer displayed The air conditioner operates normally Setting the 1 Hour Timer You can set the 1 Hour Timer to turn off the air conditioner automatically after an hour It is the quick and convenient way using only one button THR
4. 1 Press the button until the MER indicator appears on the remote control MODE 2 Press the button until the desired mode is displayed at the remote control to select the mode after setting the 1 Hour Timer Result The air conditioner operates in the selected mode for an hour If you set the 1 Hour Timer when the air conditioner is turned off the air conditioner turns on and operates for an hour To cancel the 1 Hour Timer 1HR 1 Press the button to cancel the 1 Hour Timer Result The indoor unit beeps The GHEE indicator is no longer displayed The air conditioner operates normally Operating Recommendations When you use your air conditioner it is recommended to read the following Topic Recommendation Power failure If power failure occurs when the air conditioner is operating the air conditioner turns off When the power returns the air conditioner starts up again automatically Protection mechanism When the air conditioner is started immediately after being plugged in or stopped the normal operation starts up after 3 minutes for the reason of protection Temperature and Humidity Ranges If you check the following tables you can use your air conditioner more efficiently If the air conditioner is used at Then High temperatures The air conditioner may stop operating for the reason of protection Low temperatures Water may leak and some malfunction m
5. C Result Each time you press the Y A button The temperature is adjusted by 1 C The indoor unit beeps PRRD POWER MANE e p p FAN SPEED ENERGY SAVING PRRD Selecting the Cool Mode SET TEMP m N AG You can select the Cool mode if you want to cool your room You can adjust the temperature and the fan speed when cooling 1 If necessary press the On Off button Result The operation indicator on the indoor unit lights up The air conditioner starts up in the mode you selected last The indoor unit beeps MODE 2 Press the button on the remote control until dis displayed MODE Result The indoor unit beeps each time you press the O button The air conditioner runs in the Cool mode You can change modes at any time 3 Press the Y A button to adjust the temperature until the required temperature is displayed You can set the temperature between 16 C and 30 C Result Each time you press the V A button The temperature is adjusted by 1 C The indoor unit beeps If the room temperature is higher than the selected temperature the air conditioner starts cooling If the room temperature reaches the set temperature the air conditioner stops cooling but the fan operates consistently FAN SPEED 4 Pressthe button to select the fan speed until the required settingis displayed Hwa Automatic rotated
6. gt Bia gt Kut oh Low Rat Medium Rat High Ru if Maximum FAN SPEED Result Each time you press the button the indoor unit beeps The fan speed indicator increases and decreases continuously and turns round each time you press the eum 5 To control the airflow direction refer to page 15 Selecting the Dry Mode You can select the Dry mode if you want to dehumidify your room You can adjust the temperature in this mode POWER 1 Ifnecessary press the On Off button Result The operation indicator on the indoor unit lights up The air conditioner starts up in the mode you selected last The indoor unit beeps MODE 2 Press the button on the remote control until 24 is displayed Result The indoor unit beeps each time you press the O button The air conditioner runs in the Dry mode You can change modes at any time 3 Press the Y A button to adjust the temperature until the required temperature is displayed You can set the temperature between 16 C and 30 C Result Each time you press the Y A button The temperature is adjusted by 1 C The indoor unit beeps The air conditioner starts dehumidifying and the fan speed is adjusted automatically 4 Tocontrol the airflow direction refer to page 15 FAN SPEED ENERGY SAVING Selecting the Fan Mode PRRD j FAN SEA GY SAVING You can select the Fan mode if you want to venti
7. indicator on On Timer indicator Operation modes indicator Gm AUTO COOL EB C DRY FAN Off Timer indicator 7 Turbo function indicator Airflow direction Sleep mode indicator Fan speed indicator Energy saving indicator Turbo button Power On Off button 1 Hour Timer button Mode selection button AUTO COOL DRY FAN Temperature adjustment button Fan speed button Airflow control button Timer Set Cancel button Battery check button Energy Saving button Sleep button On Timer button Off Timer button Nowe Each mode indicator shows the current setting and the battery life You can check the battery life by pressing the 4 button The number of the battery life indicator means the remaining battery life Replace the batteries when only one battery life indicator remains Inserting the Remote Control Batteries You must insert or replace the remote control batteries when You purchase the air conditioner The remote control does not work correctly Use two AAA LRO3 1 5V batteries Do not use old batteries or different kinds of batteries together Batteries may be completely discharged after 12 months even if they have not actually been used 1 Remove the battery cover in the rear of the remote control by pushing it with your thumb 2 Insert two batteries respecting the polarities as indicated by the and symbols 3 Close the cover by sliding it bac
8. Adjusting the Airflow Direction Horizontally m Setting the On Timer ooer serien ennmi eia m Setting the Off Timer cc ccc cecee cece onneni m Setting the Sleep Timer cc cece cece eee eee eee eeeeeeeee m Setting the 1 Hour Timer ccc e cece ee ee eee eeeeee eee RECOMMENDATIONS FOR USE m Operating Recommendations ee cece eee e eee eee m Temperature and Humidity Ranges eeeeeeeeee m Operating Your Air Conditioner Without the Remote Control m Troubleshooting Guide kkk kee cece n eee eee eee e eee eee m Cleaning Your Air Conditioner cece cece eee e eee eee m Cleaning Deodorizing and Bio Filter Option Name of Each Part The design and shape can be changed according to the model Temperature sensor Power On Off button Air filter Airflow blades under the grille outlet Air Inlet Timer indicator amp Fan mode indicator Bee erlag 7 Power On Off button Energy saving indicator Remote Control Sensor Operation indicator Cool mode Remote Control Buttons and Display Transmission indicator Temperature and Timer setting 1 HourTi indicat our Timer indicator Battery life
9. Register your product at www samsung com global register Safety Precautions You should take the following safety precautions when using your air conditioner Aw RNING e If you don t follow the safety precautions you may get the risk of an electric shock injury or death e The manufacturer or qualified service personnel must install this air conditioner e Unplug the electric power before repairing installing or cleaning DURING OPERATION Do not repair the air conditioner at your discretion It is recommended to contact a service center directly Never spill any kind of liquid on the air conditioner If this happens unplug or turn off the air conditioner and contact an authorized service center Do not insert anything between the airflow blades to prevent damage of the inner fan and consequent injury Keep children away from the air conditioner Do not place any obstacles in front of the air conditioner Do not spray any kind of liquid into the indoor unit If this happens turn off the breaker and contact a service center Make sure that the air conditioner is well ventilated at all times Do not place a cloth or other materials over it Remove the batteries if you don t use the remote control for a long time If applicable Use the remote control within 7 meters from the indoor unit If applicable DISPOSING OF THE UNIT Before throwing out the air conditioner remove the batteries from the FE rem
10. ay occur if the heat exchanger freezes High humidity levels Water may condense and drip from the surface of the indoor unit if you don t use the air conditioner for a long time Operation Outdoor Temperature Indoor Temperature Indoor Humidity Cooling 19 C to 54 C approx 16 C to 32 C approx 80 or less Dehumidifying 19 C to 54 C approx 16 C to 32 C approx 3 If you use the air conditioner over 32 C indoor temperature the cooling capacity may drop Operating Your Air Conditioner Without the Remote Control You can operate your air conditioner directly without the remote control 1 Toturn the air conditioner on press the On Off button on the right side of the indoor unit Result The Operation indicator on the indoor unit lights up The indoor unit beeps The air conditioner starts up in the appropriate mode for the room temperature The air conditioner changes the Cool mode automatically depending on the current temperature during operation 2 Toturn the air conditioner off press the On Off button again Even if you turned the air conditioner on with the On Off button you can control it with the remote control Troubleshooting Guide Before contacting the service center check the following It will save your time and theexpense of an unnecessary call Problem Explanation Solution The air conditioner does not operate Check if the circuit breaker of the air condit
11. ioner is switched on Check if the air conditioner is turned on If necessary press the On Off button on the remote control Check if the Timer indicator on the indoor unit is on If so Wait until the set time is reached and the air conditioner starts automatically Cancel the Timer See pages 16 and 17 for further details The air conditioner does not operate with the remote control Check if there are no obstacles in front of the indoor unit Check the remote control batteries Make sure that you are with in 7 meters from the indoor unit No beep is heard when you press the x On Off button on the remote control Check if you are pointing the remote control at the remote control sensor on the right side of the indoor unit Replace the remote control batteries if necessary The air conditioner does not cool Check if the correct operating mode has been selected Auto Cool The room temperature may be too low Check if the air filter is dirty refer to page 23 for cleaning instructions Check that there is no obstacle in front of the outdoor unit The fan speed does not change when you press the jay spe button Check if the mode is set to the Auto Cool or Fan mode in the Dry mode the fan speed changes automatically The airflow direction does not change when you press the pap button Check if the air conditioner has been turned on if necessary press the s
12. k in its place Getting Start The User s Manual provides you with valuable information about your air conditioner Please read this manual carefully before using the air conditioner It will help you take full advantage of the unit s features You have already seen the basic description of the unit on pages from 4 to 6 Starting up with the next page you will find a series of step by step procedures for each function available The illustrations in the step by step procedures use three different symbols A PRESS PUSH HOLD DOWN Selecting the Auto Mode You can select the Auto mode if you want to cool your room automatically You can adjust the temperature in this mode 1 Ifnecessary press the On Off button Result The operation indicator on the indoor unit lights up The air conditioner starts up in the mode you selected last The indoor unit beeps MODE 2 Press the O button on the remote control until An is displayed Result The indoor unit beeps each time you press the O button The air conditioner runs in the Auto mode The Auto mode cools the room depending on the set temperature The air conditioner changes the Cool mode automatically depending on the current temperature during operation You can change modes at any time 3 Press the Y A button to adjust the temperature until the required temperature is displayed You can set the temperature between 16 C and 30
13. late your room It helps to refresh the air in your room You can adjust the fan speed in this mode 1 If necessary press the On Off button Result The operation indicator on the indoor unit lights up The air conditioner starts up in the mode you selected last The indoor unit beeps MODE 2 Press the button on the remote control until cS dis displayed Result The indoor unit beeps each time you press the button The air conditioner runs in the Fan mode The temperature is set automatically You can change modes at any time FAN SPEED 3 Press the O button to select the fan speed until the required setting is displayed a Low Ra Medium AR il High FAN SPEED Result Each time you press the O button the indoor unit beeps 4 To control the airflow direction refer to page 15 Selecting the Turbo Function You can select the Turbo Function if you want to cool your room in the fastest way After the 30 minute operation with the maximum setting it returns to the previous setting POWER 1 If necessary press the On Off button Result The operation indicator on the indoor unit lights up The air conditioner starts up in the mode you selected last The indoor unit beeps TURBO 2 Press the O button Result The temperature and fan settings are adjusted automatically The air conditioner cools the room as quickly as possible After 30 minutes the air co
14. n refer to page 15 Adjusting the Airflow Direction Vertically You can adjust the airflow direction vertically The outer airflow blade moves up and down to increase the efficiency of the cooling operation FLAP ES 1 Press the O button until the required direction is set Result The outer blade is adjusted vertically FLAP 2 Press the button to move the blade up and down automatically during operation SET CANCEL ON FLAP 3 Press the button again to stop the blade moving up and down If you turn the air conditioner Then the blade Off is closed completely On set to the default position Adjusting the Airflow Direction Horizontally You can adjust the airflow direction horizontally with your hands The inner blades with small fins moves the air to the required direction 1 Adjust the inner blades by moving them to left or right Setting the On Timer You can set the On Timer to turn on the air conditioner automatically at the appointed time You can set the time from 1 hour to 24 hours 1 Press the button until the required time is displayed to set the On Timer You can set the time between 1 hour and 24 hours SETICANCEL 2 Press the button to complete the setting Result The remaining time is displayed
15. nditioner is reset automatically to the previous setting You can select the Turbo function in the Auto and Cool mode If you select this function in the Dry or Fan mode the mode changes to the Auto mode TURBO 3 Press the button again to stop the Turbo Function before the end of the 30 minute period TURBO POWER Result The air conditioner is reset automatically to the previous setting TURBO POWER THR A En MANE 4 To control the airflow direction refer to page 15 Selecting the Energy Saving Function You can select the Energy Saving Function to save energy when cooling 1 Ifnecessary press the On Off button Result The operation indicator on the indoor unit lights up The air conditioner starts up in the mode you selected last The indoor unit beeps HERD Result The indoor unit beeps The air conditioner runs in the Energy saving mode TURBO POWER ENERGY SAVING t 2 Press the O button The outer airflow blade moves up and down To stop the Energy saving mode press the N again You can select the Energy saving mode only in the Cool mode 3 Press the Y A button to adjust the temperature until the required temperature is displayed FAN SPEED ENERGY a FLAP SLEEP FN ea FAN SPEED ENERGY SAVING FAN SPEED 4 Press the button to select the fan speed until the required setting is displayed 5 To control the airflow directio
16. ote control When you dispose of the air conditioner consult your dealer If pipes are removed incorrectly refrigerant may blow out and cause air pollution When it contacts with your skin it can cause skin injury The package of the air conditioner should be recycled or disposed properly for environmental reasons OTHERS Never store or load the air conditioner upside down or sideways to _ s prevent the damage of the compressor Young children or infirm persons should be always supervised when they use the air conditioner Max current is measured according to IEC standard for safety Current is measured according to ISO standard for energy efficiency Contents PREPARATION m Safety Precautions u m Name of Each Part eee eceee eee eee ere eeeeeeeenenes m Remote Control Buttons and Display 000eeee m Inserting the Remote Control Batteries 0000s m Getting Started u nen OPERATION m Selecting the Auto Mode cc ce ceeeee cece cece eee eeeeeeeee m Selecting the Cool Mode cceee cece cece ee eeeeneee m Selecting the Dry Mode ccccce cece cece eee eeeeeeeee m Selecting the Fan Mode ccceece cece eee e eee eeeeneee m Selecting the Turbo Function ccee cece cece eeeeeeee m Selecting the Energy Saving Function eeeeee m Adjusting the Airflow Direction Vertically 0005 m
17. w On Off button on the remote control The timer is not correctly triggered Check if the timer is set correctly see pages 16 and 17 Odor permeates into the room during operation You can use the Fan mode to ventilate your room Cleaning Your Air Conditioner For the best use of your air conditioner you must clean it every 2 weeks to remove the dust that accumulates on the air filter DIPORTANT Before cleaning your air conditioner check ifyou have turned off the circuit breaker 1 Open the upper front grille by pulling the lower right and left tabs of the grille 2 Pull air filters out of each tab of the grille 3 Remove all dust on the air filters with a vacuum cleaner or brush 4 When you finish insert air filters by fixing them to each tab of the grille Body Air filter Body groove Front grille 5 Toclose the front grille fix it to hooks and push down the lower right and left tabs of the grille 6 Clean the front grille with a damp cloth and mild detergent do NOT use benzene solvents or other chemicals If you have not used the air conditioner for a long time select the Fan mode for 3 to 4 hours to dry the inside of the air conditioner Cleaning Deodorizing and Bio Filter Option
Download Pdf Manuals
Related Search