Samsung WA13QACIC User Manual
Contents
1. 10 DC68 01970B EN indd 10 e 2007 03 29 79451 2 22 34 CONNECTING THE WATER SUPPLY HOSE 1 Remove the adaptor from the water supply hose 2 First using a type screw driver loosen the four screws on the adaptor Next take the adaptor and turn part b following the arrow for gap about 5 mm between them 3 Connect adaptor to the water tap by tightening the screws firmly Then turn part b following the arrow and put a and b together 4 Connect the water supply hose to the adaptor Pull down the part c of the water supply hose When the part c is released the hose is automatically connected to the adaptor making a click sound 5 Connectthe other end of the water supply hose to the inlet water valve at the back of the washer Screw the hose clockwise all the way in 5 1 Connect the other end of the water supply hose to the inlet water valve at the top of the washer Screw the hose clockwise all the way in t Ifthe water tap is a screw type assemble a water supply hose that fits to the tap as shown the same steps e After completing connection if water leaks from the hose then repeat Nowe Use the most conventional type of faucet for water supply In case the faucet is square or too big remove the spacing ring before inserting the faucet into the adaptor Note DC68 01970B_EN indd 11 The appliance is to be connected to the water mains using2. INDIA 1600110011 www samsung com in MALAYSIA 1800 88 9999 www samsung com my 1800 10 SAMSUNG PHILIPPINES 7267864 www samsung com ph 1800 SAMSUNG SINGAPORE 7267864 www samsung com sg VIETNAM 1 800 588 889 www samsung com vn RUSSIA 8 800 200 0400 www samsung com ru 0860 7267864 SOUTH AFRICA SAMSUNG www samsung com za 2007 03 29 9951 2 22 54
3. inlet water 3 The doorsill shoudn t be more than 5cm g valve 1 Pulloutthefilterand 2 Pullin the filter and 3 Check if there is a wash well connect the hose to leakage the inlet water valve Note to tighten up the 4 Dont install the drain hose underneath the wash tightly machine 12 DC68 01970B EN indd 12 e 2007 03 29 7451 2 22 46 CLEANING THE FILTER Clean the filter net often to keep the washer clean 1 Push the upper part _ of the Magic filter and pull in 1 Push up and pull out the filter net Open the cover as shown in the 2 Remove the collected lint from the figure filter net Close the cover and insert the lower part of the filter in the basket first and then push the filter with click sound HOW TO CLEAN THE PUMP FILTER Qi Place a rag under the washer filter not to Rotate the filter counterclockwise and pull Remove dirts and rotate the filter wet the floor OPEN NS FILTER 9 CHOSE out the filter clockwise until it locks in position ge X DC68 01970B EN indd 13 13 TROUBLESHOOTING gt Washing machine won t work Is the water tap opened Is the washer plugged in Is the power cut off Is there enough water gt Water dose not drain Is the drain hose down No pump Is the drain hose frozen Is the drain hose clogged If the water dose n
4. Close the lid WOOL COURSE Washable sweater cardigan delicate clothes etc Power Course Start Hold D Press the power button to ON Press the course select five times Press the START HOLD button Washing rinsing and spinning follow If you want to pause press the START HOLD button again You can change the course when paused 4 Close the lid CAUTION Donotuse water above 30 C For WOOL washing Referto the tag attached on the clothes for washing information Fasten buttons and turn inside out before washing Usethe detergent indicated in the laundry When the degree of dirt is extreme soak the laundry in warm water for about 10 minutes before pressing the WOOL course button in order to enhance washing efficiency M DELAY START How to reserve washing Select this course when you have to go out or do something else UNA Power Course Delay Start Start Hold lt Au Press the power button to ON Pressthe course select button Press the DELAY START button once You may change the delay start time with use the DEALY START button from 3 hours to 19 hours 4 Press the START HOLD button and put the proper amount of detergent into tub 5 Closethe lid The washing finishes by the time you reserved UNA DC68 01970B EN indd 8 Add detergent and softener in proportion to the water level Then close the lid e Must add the detergent in the detergent box Ifthe
5. 12 CLEANING THE FILTER 25524 e oe dote 13 HOW TO CLEAN THE PUMP FILTER 13 TROUBLESHOOTING 13 WASHING MACHINE WON T WORK 14 SPECIFICATIONS a t n np RUE n a ete ss 14 CODE NO DC68 01970B 03 EN 2007 03 29 9451 6 FEATURES DC68 01970B EN indd 2 E Silver Nano Health System This is a washing control system that protects the skin from harmful bacteria and that enables refreshing cleansing and sanitation through anti bacteria coating and by killing bacteria that are hidden in clothes at the time of washing or rinsing Moreover it prevents proliferation of bacteria through anti bacteria coating of washed clothes Sterilization algorithm Nano silver fast water during washing Initial washing with powerful water stream Soak for a fixed period of time sterilize afterwards Finish after regular washing e Anti bacteria coating Nano silver fast water during the last rising from regular stroke Soak for a fixed period of time during rinsing anti bacteria coating in between Finish rinsing CAS SYSTEM CHILD LOCK FUNCTION AUTO RESTART The power is turned on automatically after power failure SAVING ENERGY The SPEEDY COURSE it is a wash course to saving the energy reduces laundry time for frequent and soiled clothes DIGITAL FUZZY CONTROL DIGITAL FUZZY control op
6. 72 way before adding into the spin basket gt A Donot wash the electric blanket and carpets Geta laundry net for those light and big volume laundry eg Cashmeres because they might rise in the water and get damaged SOAK COURSE Power Power Course Start Hold Course Start Hold Aun 1 Press the POWER button 2 Press the course select button twice 3 Press the START HOLD button once Water level is selected automatically Washing rinsing and spinning follow 4 Close the lid E SUPER CLEAN COURSE Power Course Start Hold Aug os d Operates only in cold water 1 Press the power button to ON 2 Pressthe course select button three times 3 Press the START HOLD button and put the proper amount of detergent into tub Water level is selected automatically Water level is only selected MAXIMUM MED LOW 4 Close the lid The washing finishes by the time you reserved 2007 03 29 9451 2 22 27 M SPEEDY COURSE If you want to wash those frequently used towels or less dirty laundry time Because washing is speedy it is good for light or less stained laundry Power Course Start Hold Auto Of Alta nest 1 Press the power button 2 Press the course select button four times 3 Press the START HOLD button Water level is selected automatically Washing rinsing and spinning follow If you want to pause press the START HOLD button again You can change the course when paused 4
7. SOAK gt SUPER CLEAN gt SPEEDY gt WOOL gt DIGITAL FUZZY SILVER WASH BUTTON te Sterilization and Anti bacteria washing in progression during selection t Manual use wash trinse spin gt Sterilization Anti bacteria wash spin gt Sterilization rinse spin gt Anti bacteria wash rinse gt Nano silver does not operate E WASH BUTTON Determines wash time period whenever you press the button E RINSE BUTTON Determines rinse time period whenever you press the button SPIN BUTTON Determines spin time period for drying laundry whenever you press the button WATER LEVEL SELECT BUTTON According to the washload select the water level m MEDIUM gt HIGH gt MAXIMUM gt HIGH gt MEDIUM gt MED LOW gt LOW gt EXTRA LOW WATER SUPPLY SELECT BUTTON As you press this button the type of water is selected as follows COLD gt COLD HOT HOT gt COLD REMAINING TIME INDICATOR LIGHT The indicator light shows the remaining time in minutes of each wash cycle Atthe end of the cycle the power automatically switches off Power Auto OK Start Hold Auto est Delay Start Course e Wash Rinse fais Spin p z Water Level Water Supply 2007 03 29 9451 2 22 24 HOW TO WASH AUTOMATICALLY DEPENDS ON THE LAUNDRY Before starting washing check the following e Connect the water supply hose to the water tap Leave a tap ope
8. before washing Cashmilon and those garments having big volume and lightweight eg Lasedecorated clothes lingerie nylon stocking synthetic fabrics etc may rise and cause damages to the clothes and problems to the machine Use the laundry net or wash them separately t Must put those long stringed clothes lase worked clothes bed cover sheet wool clothes into a laundry net before washing t Put delicate clothes in the laundry net t Use only those commercial laundry net for washing Curtains floating garments or blue jeans shall be pressed not to float on the water t f they are floated on the water press Start Hold button to stop and press them to sock in the water If the washing goes on with clothes floating on the water it may cause damages to the clothes and the washing machine as well as unsatisfactory washing result DC68 01970B EN indd 6 CONTROL PANEL For more details see control panel of your washing machine POWER BUTTON Press this button once to operate Press once again to turn the power off START HOLD BUTTON Use to pause and restart the operation To change the washing procedure during operation press this button to stop and once again to restart after changing the procedure M DELAY START BUTTON Press this button when delay start washing is needed COURSE SELECT BUTTON With every press of this button the washing course changes DIGITAL FUZZY BLANKET HEAVY gt
9. the Spin Dry cycle If added too early its effectiveness will decrease 2 After directing the drain hose to a drain join to the drain outlet of the washing machine Do leave the softener into the Softener _ Dispenser for a long time Because softner became stiff drain outlet anpa TY M HOW TO PUT THE DETERGENT IN 1 Open the detergent box by pulling in the direction ofthe arrow as shown in the figure and then put the powder detergent in the detergent box 2 Put in one time amount of detergent evenly so the detergent may not brim 3 Be sure to join them tightly by pressing the joint ring and pushing it into the drain outlet The length of drain hose is adjustable so that you can extend the length appropriately over the box Detergent Device CN MEE Put the detergent in 1 HOW TO CHANGE THE DRAIN HOSE DIRECTION proportion to Water handle of joint ring is pressed to pull out the drain hose level Change the direction of the drain hose and follow the above guideline again CAUTIONS WHEN INSERTING THE DRAIN HOSE Softener Device 1 Don t exceed more than 3m when the drain hose Softener _ Lol is used by connecting whth other hoses Lessthanm baseline Us FERE CAUTION If softener is stored over the above base line it may flow down at any rpm a time WATER SUPPLY CONNECTOR FILTER 2 Be careful to drain water out at the end ofthe drain hose
10. the WASH and RINSE button is pressed during working Wash time period is determined between 6 and 30 minutes and rinse time is determined between 1 and 5 times Auto ON E E S Rinse Start Hold RINSE AND SPIN Press the RINSE and SPIN button Press the START HOLD button once Rinsing and spin drying follow When the RINSE and SPIN button is pressed during working The number of rinse times is determined between 1 and 5 and spin time period for drying is determined between 1 and 9 minutes DC68 01970B EN indd 9 Power Auto OK Rinse Wash E Spin Start Hold WASH RINSE AND SPIN Press the WASH RINSE AND SPIN button Press the START HOLD button once WASH RINSE AND SPIN is performed Power Auto OK Start Hold SILVER WASH with WASH RINSE AND SPIN Press the SILVER WASH button Press the START HOLD button once WASH RINSE and SPIN is performed Anti bacteria coating is operation if silver wash is selected Operates only in cold water Sterilization Anti bacteria coating x 9 E Auto of Rinse Start Hold SILVER WASH with RINSE AND SPIN Press the SILVER WASH button Press the RINSE button once Press the START HOLD button once Rinsing and Spin drying follow Anti bacteria coating is operation if silver wash is selected Operates only in cold water Anti bacteria coating 8 Auto of Wash am
11. they must be closed before washing t f stains are found use the towel wet with detergents to rub on in a single Wash winter jumpers working uniforms bed cover direction sheets and blue jeans separately t Before washing the sleeves collar dress hem and pockets are pre treated by Fold clothes well into the spin basket Must remove the brushing with detergents curtain hooks before washing The wrinkle processed clothes made of wool are specially treated by fixing them with t Turn inside out the button decorated and embroidered threads before washing The threads shall be removed after the clothes are dried clothes before washing Not washable laundry iei a those metal decorations because they cause heavy damages while Clothes those are easily transformable even by soaking in water zx The long stringed clothes may tangle with other clothes Must t Even by soaking in water neckties brassieres jackets suits and coats can be fix the strings before washing easily transformed like shrinking and discoloring on the garment surfaces t The metal from brassieres may stick out and damage other because they are mostly made of rayon polynosic cuff and their blend fabrics clothes or the spin basket Must use the commercial laundry t The wrinkle processed embossed or resin processed products are easy to net for washing brassieres Use a laundry net of fine mesh transform even by soaking in water Waterproof clothes Ski Wear Diape
12. DC68 01970B_EN indd ET WASHING MACHINE Silver Nano Health System Users Manual Please read this manual before using and note how to use in the proper manner Please be careful of keeping the manual Otherwise it should be bought separately The User s Manual is for common use Make use of the User s Manual depending upon your washing machine model Register your product at www samsung com global register 1 FEATURES RUE 2 SAFETY INSTRUCTIONS 3 DESCRIPTION OF PARTS 4 CHECKING BEFORE WASHING AND CARING FORGARMENTS 5 CONTROL PANEL 6 oi 6 HOW TO WASH AUTOMATICALLY DEPENDS ON THE LAUNDRY 7 Keeping thetubclean 2 44 24808 du dunes eet ERE ew 8 MANUAL FUNCTIONS 9 INSTALLATION amp 10 ENVIRONMENT dor eae 10 Haus ccr 10 CONNECTING THE WATER SUPPLY HOSE 11 ASSEMBLING THE RAT PROTECTION PANEL 11 HOW TO CONNECT THE DRAIN 11 HOW TO ADD THE FABRIC SOFTENER 12 HOW TO PUT THE DETERGENT IN 12 WATER SUPPLY CONNECTOR FILTER
13. WATER DRAIN HOSE ADJUSTABLE LEGS 25 i Adjust the length of the legs when i installing the washer 0 CE SOUND ABSORPTION PANEL D668 01970B EN indd 4 e 2007 03 29 9451 2 22 18 CHECKING BEFORE WA SHING AN D CARING FOR CLOTHES BEFORE WASHING t Must follow the checkpoints in order to avoid machine problems or damages CARING FOR GARMENTS on garments t If the below problems are caused by customer s faults separate service fee will be charged Must follow the checkpoints in order to avoid machine problems or damages on garments t f the below problems are caused by customers faults separate service fee will Take mem ersonal belongings from a be charged t Caution Check the pockets Hairpins and coins cause damages to clothes and washing machine Checkpoints Before Starting Washing They make noise and problems to the machine Must Check if the clothes are bleaching or not check the pocket te Add liquid detergent to a white towel and the garment where you can t notice If pants zippers are open while washing the spin basket may be damaged The well Then rub together strongly Check if the color transferred to the towel zipper should be closed and fixed with a string before washing t Be careful for scarves and imported clothes since they are easily discoloring t f blue jeans and working uniform s zippers or hooks are Check for stains or partial dirt m made of steel
14. detergent is spread on the laundry directly some clothes may get discolored as the start delays e Ifthe Delay Start needs to be canceled press the power button The reserved finish time may be changed depends on the water pressure E SILVERWASH Power Start Hold 1 Press the power button 2 Press the SILVER WASH button 3 Press the START HOLD button Water level is selected automatically Washing rinsing and spinning follow If you want to pause press the START HOLD button again You can change the course when paused 4 Close the lid CLEANING THE TUB Power Pr 2 Press the POWER button Press the COURSE button to select the BLANKET course Press the WATER LEVEL button to select MAXIMUM Press the START HOLD button Add a dedicated detergent and close the lid k Never place laundry in the tub when cleaning inside the tub as this can cause discoloration or damage to the laundry When doing the laundry after cleaning the tub you may find some impurities These are just detergent residues and impurities after the tub cleaning Perform the rinse cycle two to three times Keeping the tub clean When using the machine under humid conditions for an extended time various bacteria from the air may stick to the tub and form black dirt fungi causing damage to the human body To keep the tub clean and hygienic at all times it is recommended
15. duct warranty does not cover problems resulting from disassembling the product Do not use this product for business purposes For washing machines with ventilation openings in the base that a carpet must not obstruct the openings DC68 01970B EN indd 3 CAUTIONS There might be a slight injury or damage when you violate this instruction Dont install it in the area with moisture or outdoor where it has rain or snow An electric shock or a fire may take place Please unplug the power supply cord when you do not use it An electric shock or a fire may take place If there is dust or water on the power supply plug and its connected part please remove it completely An electric shock or a fire may take place Do not make your kids look into the inside of the washer If your kid falls into the washer his life could be in danger Ventilate immediately without touching the power plug if gas is leaking An electric shock or a fire may take place if it catches flame If the washer makes strange noise smell or smoke unplug it promptly and call service agent An electric shock or a fire may take place When cleaning don t spray water to the parts of the washer directly It may make it s life span shorten Also an electric shock or fire may take place Don t use several appliances together with an outlet Afire may take place due to unusual heat Don t press the button with an awl or pin An electric shock o
16. erates with best washing course by sensing the washload like artificial intelligence TRANSPARENT WINDOW quip This Transparent Window is the new concept to solve the curiosity of users to see inside of washing machine while operation While operation the laundry progress inside of washing machine can be checked by looking through the transparent window PULSATOR The Pulsator helps water and detergent to go through fabrics efficiently while providing both the powerful water action to clean lager and heavier clothes and the gentle water action to clean all delicates with less wear and tear on clothes WATERFALL FLOW The Waterfall Flow injected from under the pulsator cascades with full force back into the tub pushing down any clothes that float right under the water surface It is this Waterfall Flow that enables this washing machine to effectively wash large and heavy items such as blue jeans and blankets E MAGIC FILTER Gulp This unique magic Filter ensures that all the lint inside the tub is captured for top quality filtering results to deliver consistently effective cleaning results SOFTENER DISPENSER The Softener Dispenser releases the fabric softener at the appropriate time when the last rinsing proceeds SUPER CLEAN SUPER CLEAN adjust the level of water by 5 steps so as to enhance detergent efficiency by adjusting the density of detergent to normal density CHILD LOCK FUNCTION This is a device to protec
17. n Plug the power cord in Make sure to lay down the drain hose E WASHING FORTHE FIRST TIME Before washing clothes for the first time you must run a complete cycle without clothes To do this 1 Press the POWER button y 2 Pour a little detergent into compartment inthe detergent drawer weg 3 Turn on the water supply to the washing machine 4 Pressthe Start Hold button This will remove any water from the manufacturer s test run remaining in the machine SPECIAL NOTES Automatic Sensing Function e At every course except wool course the amount of laundry is automatically sensed and then appropriate water level washing time rinsing cycle and spinning time are automatically selected for automatic washing e After the power is on a course is selected and Start Hold button is pressed Then the washing board starts spinning without water This action senses how much laundry is in the washing basket not a machine problem After this sensing process water supplies automatically Adding Detergent and Softener e 1158056516 amount of laundry and indicates the water level and amount of detergent Then it starts water supply right away During the water supply it is possible to open the detergent box and add detergent However it is better to press Start Hold button to stop water supply and add detergent Close the lid and press Start Hold button again This way is much more convenient Ifthe softener is inserted in
18. new hose sets and that old hose sets should not be used 11 ASSEMBLING THE RAT PROTECTION PANEL Tilt the washer a little and lift up the panel until it clicks finally fix the panel with screw to the base as shown in the figure Rear side 1 Insert the sound absorbing panel to the assembling hole on back side to the end 2 If you have difficulty inserting the panel lift up the washer a little and insert it THEPROTECTION PANEL IS NOT APPLIED IN SOME MODELS HOW TO CONNECT THE DRAIN HOSE IN CASE OF PUMP DRAINED WASHER Take out the cap hose and connect the outlet hose Be sure to join tightly the drain hose into the drain outlet on the back of the machine Be sure to join tightly the drain Install the drain hose in the position of about hose into the drain outlet on the side of the machine 90 100cm 90 100 above the ground 2007 03 29 9451 2 22 41 c IN CASE OF GENERAL WASHER E HOWTO ADD THE FABRIC SOFTENER 1 After pressing the joint ring insert to the drain hose When a proper amount one time does of fabric softener is stored in the softener inlet it is automatically put in at the last rinsing cycle Donot use detergent bleach or starch into the Softener Inlet e Using too much softener may produce unsatisfactory results Do not open the lid during
19. ot drain in 15 minutes a buzzer will sound and the remaining time indicator will show gt Water is not supplied Is the water tap opened Is the water cut off Is the water supply hose or hose connection clogged Isthe water tap frozen If water is not supplied in 1 hour a buzzer will sound and the remaining time indicator will show 4E gt Spinning does not work Is the laundry spread out evenly in the washer In the washer set on a sturdy flat surface gt Water is overflowed Restart after spinning If the error sign still indicates call agency 2007 03 29 945 2 WASHING MACHINE WON T WORK The power is cut off Check1 gt electric voltage normal Check2 gt Is the washer plugged in Plug in the electric cord Water does not drain Check3 Is the drain hose down Put the drain hose down Check4 gt Is the drain hose folded Unfold the drain hose Check5 Is the drain hose outlet clogged Remove the waste cleanly Washing machine won t work Check1 the washer lid open Close the lid Check2 gt the Hold button on Press the Start Hold button one more time and check if the washer starts Check3 gt Is enough water filled to the water level gt If the water pressure is low it takes a long time to start washing Check4 15 the faucet closed Open the faucet to supply water If the drain hose and spin basket are frozen do as follows Add hot wate
20. p Start Hold SILVER WASH with WASH AND SPIN Press the SILVER WASH button Press the WASH button once Press the START HOLD button once Wash and spin drying follow Anti bacteria coating is operation if silver wash is selected Operates only in cold water Sterilization 2007 03 29 79451 2 22 31 INSTALLATION MAINTENANCE ADJUSTMENT THE HEIGHT OF THE MACHINE The User s Manual is for common use Make use of the User s Manual depending upon your washing machine model M ENVIRONMENT Leave some space Maintain at least 10cm between the washer and the wall Place the washer on a sturdy flat surface If the washer is placed on an uneven or weak surface noise or vibration occurs Allowable is 1 Adjust the legs for even placement Never install the washer near water Do not place the washer in steamy rooms or where the washer is directly exposed to rain Moisture may destroy the electrical insulation causing an electrical shock Adjust the legs to level the washer Be careful not to put in your hand under the legs Pull the handles located at the right and left of the front side and slide off Adjust the height of the machine upward or downward When the adjustment is finished push the handles to fix the adjusting legs hazard Avoid direct sunlight or heaters Waterdrop Cause How to level As plastic an electrical components are affected by direct heat never place the ma
21. r Covers Footboards are not allowed for t Easily discoloring products made of cotton and wool wrinkled silk leather f products leather accessory leather ornamented clothes and its accessory i t Don t wash those clothes without handling guideline or material indication tag The waterproof sheet clothes and non water permeable fabrics shouldn t be washed rinsed or About Detergent put in a spin basket The laundry may pop out and t When detergents are not dissolving well use warm water about 40 C to cause severe vibration so that a person may get dissolve the detergent damaged and the machine wall and floor may Caution break out in addition to clothes Examples are diaper cover waterproof wear Use an appropriate amount raincoat umbrella cover ski wears car cover sheet and sleeping bags Even if excess amount of detergent is used there is not much difference in Cautions During Spinning washing result It may cause damages to the garments because rinsing is not t Spinning of regular garments enough The water from garments is drained out through the spin basket holes t The bleaching agent may cause damages to garments since it is strong alkali t Spinning of waterproof clothes and fabrics t Do sufficient rinsing because the powder detergent is easily remained on the Even if the spin basket spins water can t drain out from the waterproof garments causing bad odors clothe
22. r a fire may take place Use the new hose sets and old hose sets should not be reused If the damage is found on the current cord in use it should be replaced by manufacturer service cener or authorized person in order to avoid the risk Connect the grounding wire to the shell plate and bury it under at least 25cm of earth elternatively connect the ground wire to the appropriate pin on a properly grounded power receptacle Never connect the w ire to a telephone line lightning rod or gas pipe 2007 03 29 9451 7 DESCRIPTION OF PARTS The User s Manual is for common use Make use of the User s Manual depending upon your washing machine model COD Be sure to keep the lid closed 777 WATER SUPPLY HOSE HOT during washing and spinning Silver Nano Health System ts WATER SUPPLY HOSE COLD DRAIN HOSE PUMP FILTER 7 Le Lint will be collected in the filter during washing 0 0 0 0 1 0 DETERGENT BOX 0 0 0 0 SPIN BASKET aa POWER CORD Jl BLEACH INLET il waTERDROP MARK 7 l7 1 i PULSATOR 5 dil cass GROUND WIRE i When the water pipe is metal make sure to FRONT CONTROL PANEL cover the end of the ground wire i p
23. r to the frozen water tap and remove the drain hose Soak into hot water e Pour hot water into the spin basket for about 10 minutes e Puta hot water towel on the drain hose connector Ifthe drain hose defrosts connect again and check for proper water draining The water drains out immediately The drain is clogged with coins or pins The drain hose is hung over the drain hose hook Half fill the spin basket with water and try for spinning again The water leaks at the water supply hose connector Check1 gt Ifthe faucet connecting part is loose water may leak gt Repeat the assembling steps again Refer to Connecting the water supply hose Check2 gt Check ifthe rubber packing of water supply hose is in the right position Screw tightly again Check3 15 the water supply hose folded gt Unfold the hose Check4 Ifthe water supply is too strong water may leak Close the faucet a little Check5 gt Is water leaking from the faucet itself Fix the faucet Water is not supplied Check6 Did you press the Start Hold button after selecting the water supply gt If the Start Hold button is not pressed water is not supplied Press the Start Hold button Check7 Isthe faucet closed Turn on the faucet DC68 01970B EN indd 14 Check 8 gt Check 9 gt Is the filter net at the water supply hose connector clogged with dirty matters Clean the filter net by brushing with a toothbrush Is the water s
24. re may take place Do not install the washer nearby electric implement or don t put a candle light or cigarette light on the washer Afire may take place During operation do not put your hands or metal materials under the washer You may be hurt by spinning board beneath the washer Stay away from the washer when the bottom of the washer sinks into the water There might be an electric shock Please wait until the water drains out completely Do not put laundry stained with gasoline benzene or alcohol in the washer and keep the materials away from the washer An explosion or a fire may take place During spinning don t put your hand in the spinning tub It may hurt your hands If it does not stop within 15 seconds after you open the lid call service agent immediately This appliance is not intended for use by young children or infirm persons unless they have been adequately supervised by a responsible person to ensure that they can use the appliance safely Young children should be supervised to ensure that they do not play with the appliance This appliance has to be connected to the plug endurable to proper power consumption This appliance has to be positioned so that the plug is accessible after installation No user serviceable parts inside Refer any servicing to qualified service personnel Otherwise this may cause a mechanical error electric shock fire or physical damage The pro
25. reading Cleaning the Tub above and using only dedicated or recommended detergents to clean the tub regularly at least once every one to three months Auto Course Water Level Start Hold 2007 03 29 9951 2 22 28 MANUAL FUNCTIONS Sterilization and anti bacteria coating are optional depending on the selection or no selection of stroke Nano silver system perates only when hydration is selected Power Auta of Wash Start Hold WASH ONLY Press the POWER button Press the WASH button Press the START HOLD button Washing goes on for 20 minutes When the WASH button is pressed during washing the wash time can be changed to between 6 and 30 minutes in duration Power Rinse Start Hold RINSE ONLY Press the RINSE button Press the START HOLD button Rinsing goes on for 2 times When the RINSE button is pressed during rinsing the rinse times can be changed to between 1 to 5 times in duration Power Spin Start Hold SPIN ONLY Press the SPIN button Press the START HOLD button Spin drying goes on for 10 minutes When the FUNCTION button is pressed during spinning the spin time can be changed to from 1 to 9 minutes Power Auto 0 Rinse Wash Start Hold WASH AND RINSE Press the WASH and RINSE button Press the START HOLD button once Detects the amount of laundry and determines wash and rinse time period automatically When
26. rk washer near furnaces boilers etc Do not place under direct sunlight os The front part is Level it by adjustable legs M LEVELLING lower If the washer is not leveled with the ground it makes the machine tremble gt more or be out of order So make sure that the washer is leveled properly SEE IF THE MACHINE IS PLACED LEVEL BY CHECKING THE POSITION OF THE WASHING TUB Water lt The back partis Adjust the height by using the adjustable e Open the lid of the machine pour water into ER lower rubber or prop at the back the tub up to the level just below the pulsator and adjust the legs so that the pulsator is positioned at the center of the water as shown in the figure r 5 7 e Place the machine more than 10cm away from the wall The left partislower Adjust the left part by using the Adjust the legs on feet O adjustable legs at the front and the adjustable rubber at the back Leveling With the Leveling Screw Manual Adjustable Feet 2 Therightpartis Adjust the right part of the washer by OR lower using the adjustable leg at the front and the adjustable rubber at the back Gently lift up the machine When done put e After adjusting and turn the adjustable it down to the the feet do not feet to the left to find the original position forget to fasten optimal balance the locking nut for safety purposes Failing to do so may cause it to loosen
27. s and fabrics Therefore water gathers to one side and this cause a t ftoo much detergent is used or cold water is used it doesn t dissolve severe vibration If the spin basket spins at a high speed water still can t drain completely and remain on the garments hose or spin basket causing out from the waterproof clothes and fabrics As a result garments move up contamination on clothes and pop out with a big vibration t n case of reserved washing detergents must be put in the detergent box If the powder detergents are spread on laundry directly it may cause discoloration DC68 01970B EN indd 5 e 2007 03 29 54b 2 22 20 Shake the dirt or soils from clothes t Soil and sands may rub delicate garments to cause damages and the washing result may be unsatisfactory For protection of baby skin t Wash diapers and baby wears baby clothes baby towels etc separately Dirt may get to baby s clothes from adult s clothes if washing them together Do pre washing for white socks sleeves and collars before the main washing t Use powder and liquid detergents t Don t use soap It may leave dirt to the spin basket Turn inside out for those nappy clothes before washing t f clothes have too much foreign matter separate them for washing Other clothes may pick up those dirty matters dirt thread t Wash black colored clothes and cotton towels separately If they are washed together towels may pick up dirty matters Check
28. t children from being accidentally hurt while playing with the washer How to start Child Lock function e Pressthe Power button to go to an initial washing mode pressing Start Hold button you start washing in case Child Lock function is needed during the laundry Press both the Water level and Wash buttons in simultaneously and get the function started Note You cannot perform the function without the Power button on Torelease the function of Child Lock Incase the Child Lock is programmed press both the Wash and Water level buttons in simultaneously 2007 03 29 9451 7 SAFETY INSTRUCTIONS Please note that the following precautions for safety intend to prevent unpredictable danger and damage by helping the proper use in safety When using hot water in washing please make sure that the water should not exceed 50 C Plastic parts may be deformed or damaged and an electric shock or a fire may take place WARNING There might be serious injury or fatal accident when you violate this instruction If the plug power supply cord is damaged it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard Do not pull the cord off or touch it with moist hands An electric shock or a fire may take place Do not bend the power supply cord by force or press it with heavy things An electric shock or a fi
29. the softener dispenser it automatically adds in at the last rinsing cycle Put the laundry into the washer and add detergent too Be careful not to overload Use right detergent for the fabrics you are washing e__f Ifthe lid is open while running the washing machine is stopped hei automatically for safety Except water supply continues while the lid is open When hot water is selected both cold and hot water are supplied for the first 20 seconds in order to protect the clothes Possible to control the washing time rinsing cycle and spinning time at every course during the washing DC68 01970B EN indd 7 Power Start Hold DIGITAL FUZZY COURSE Selects the best washing course automatically 1 Press the POWER Button to ON 2 Pressthe START HOLD button Water level is selected automatically Washing rinsing and spinning follow If you want to pause press the START HOLD button again You can change the course when paused 3 Closethe lid BLANKET HEAVY COURSE Big volume laundry like blanket and bed cover sheets 1 Press the power button to ON pd d 2 Press the course select button once 3 Press the START HOLD button Water level is selected automatically Washing rinsing and spinning follow If you want to pause press the START HOLD button again You can change the course when paused 4 Closethe lid Fold those big volume laundry blanket and bed cover sheets inthe following
30. upply cut off gt If the water supply is suspended turn off the faucet and power off Spinning makes loud noises and vibrations Check 1 gt Check 2 gt Check 3 gt Check 4 gt Check if the laundry is spread evenly in the washer Spread out the laundry evenly and start again Check if the washing machine levels on a sturdy flat floor Set the machine at level Is the handle for leveling legs loose Adjust the legs on the feet for leveling Is around the washing machine filled with unnecessary stuffs Remove those unnecessary things away from the wash machine SPECIFICATIONS POWER CONSUMPTION WASH 500W 550W SPIN 300W DIMENSIONS mm WEIGHT 47kg 53kg WATER PRESSURE Gen 5 WASHING TYPE Stirring Type STANDARD WATER LEVEL MAXIMUM 911 HIGH 781 MEDIUM 621 MED LOW 481 E LOW 321 WATER USAGE 2351 2401 PULSATOR ROTATING SPEED 120 rpm SPIN SPEED 710 rpm For operating VOLTAGE and FREQUENCY see the LABEL RATING on the back of washing machine 2007 03 29 79451 2 22 53 MEMO 15 DC68 01970B EN indd 15 2007 03 29 79 45 2 22 54 DC68 01970B_EN indd Contact SAMSUNG WORLD WIDE If you have any questions or comments relating to Samsung products please contact the SAMSUNG customer care center Country Customer Care Center Web Site AUSTRALIA 1300 362 603 www samsung com au 3030 8282
Download Pdf Manuals
Related Search