Home

Samsung NP-Q320E User Manual (Vista/Windows7)

1. Unintentional Emitter per FCC Part 15 This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy If not installed and used in accordance with the instructions it may cause harmful interference If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet ona circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help 31 If necessary the user should consult the dealer or an experienced radio television technician for additional suggestions The user may find the following booklet helpful
2. Connecting a wired LAN while using a wireless LAN may not activate the lt Wake On LAN gt function Set the Wireless LAN to Disable to use the lt Wake On LAN gt function For Windows 7 Wake On LAN is not supported Ping Q When I am connected to a 100Mbps 1Gbps wired LAN and the computer exits Sleep hibernation mode a message appears informing you of a connection to a 10Mbps 100Mbps wired LAN When the computer exits standby hibernate mode restoring the network takes about 3 seconds When the network is restored it operates at 100Mbps 1Gbps The Home Group function for the Windows 7 operating system only A Home Group is a function that enables connecting all the computers at home allowing users to access the data on all computers as if accessing the data on the local computer If you set the first computer to use a Home Group as a Home Network you can create a Home Group A second and more computer can participate in the created Home Group A password is required for participation and you can confirm the password on the first computer This function is only available between computers that have the Windows 7 operating system installed If an older operating system than Windows 7 is installed on a computer the computer cannot create or participate in a Home Group In addition the Windows 7 Starter version does not support the Home Group function Wireless Network WLAN Related The signal stre
3. 1 Wireless Network optional A wireless network Wireless LAN environment is a network environment that enables communicating between multiple computers at home or a small size office through wireless LAN devices Before You Start The descriptions below are for computer models with a Wireless LAN card or device A Wireless LAN device is optional The pictures in this manual may differ from the actual product depending on your wireless LAN device model To use the wireless LAN you have to turn the wireless LAN on first by pressing the Fn keys If the wireless LAN is turned on the Wireless LAN LED Y is lit What is an Access Point AP An AP is a network device that bridges wired and wireless LANs and corresponds to a wireless hub in a wired network You can connect multiple wireless LAN installed computers to an AP Connecting to a Wireless LAN If there is an AP you can connect to the Internet via the AP using the Wireless LAN connection method provided by Windows gt For Windows 7 1 If you click the Network Connections icon in Mot connected aiil Connections are available the system tray a list of available APs appears If Wireless Network Connection you select an AP to connect to the Connect button R4 COM_19F AP List appears Open Network and Sharing Center 9 38 PM 7 8 2009 Click Connect If a network key is set for the AP enter the network key and then click Connect Not
4. If a heavy object is pressed against the notebook computer a white spot or stain may appear on the LCD Therefore take care not to apply any pressure to the notebook In this case place the notebook computer in a separate compartment away from the other objects 15 AN Caution Failing to follow instructions marked with this symbol may cause slight injury or damage to the product Installation Related Do not block the ports holes vents etc of the product and do not insert objects Damage to a component within the computer may cause electric shock or fire When using the computer with it lying on its side place it so that the vents face upwards Failing to do so may cause the internal temperature of the computer to rise and the computer to malfunction or halt Do not place a heavy object over the product This may cause a problem with the computer In addition the object may fall and cause injury or damage the computer Battery Usage Related Dispose of worn out batteries properly There is a danger of fire or explosion The battery disposal method may differ depending on your country and region Dispose of the used battery in an appropriate way Do not throw or disassemble the battery and do not put it into water This may cause an injury fire or explosion Use only a battery authorized by Samsung Electronics Failing to do so may cause an explosion 16 Avoid cont
5. Something About Interference This is available at FCC local regional offices Our company is not responsible for any radio or television interference caused by unauthorized modifications of this equipment or the substitution or attachment of connecting cables and equipment other than those specified by our company The correction will be the responsibility of the user Use only shielded data cables with this system Intentional emitter per FCC Part 15 If fitted with 2 4G band or 5G band Low power Radio LAN type devices radio frequency RF wireless communication devices operating in the 2 4GHz 5GHz Band may be present embedded in your notebook system This section is only applicable if these devices are present Refer to the system label to verify the presence of wireless devices Wireless devices that may be in your system are only qualified for use in the United States of America if an FCC ID number is on the system label This device is restricted to indoor use due to its operation in the 5 15 to 5 25 GHz frequency range FCC requires this product to be used indoors for the frequency range 5 15 to 5 25 GHz to reduce the potential for harmful interference to co channel Mobile Satellite systems High power radars are allocated as primary users of the 5 25 to 5 35 GHz and 5 65 to 5 85 GHz bands These radar stations can cause interference with and or damage this device The FCC has set a general guideline of 20 cm
6. Chapter 1 Getting Started Product Features Before You Start Contents Safety Precautions Proper Posture During Computer Use Important Safety Information Replacement Parts and Accessories Regulatory Compliance Statements WEEE SYMBOL INFORMATION Overview Front View Status Indicators Right View Left View Back View Bottom View Turning the Computer On and Off Turning the computer on Turning the computer off N OOU N 21 24 26 28 40 41 41 42 43 44 45 46 47 47 48 Product Features High Performance Notebook Computer Intel Core 2 Duo Pentium Dual Core Celeron processor and DDR Il Memory Wireless LAN Optional Bluetooth Optional Supports Various Multimedia Functions A video chatting conference function adopting the camera module Optional An HDMI port that enables viewing a full HD picture on the TV Optional Easy to Use and Convenient Functions Various Hot Key Functions Multi Card Slot Luxurious Ergonomic Design Convenient Touchpad Gesture Functions Optional Q Optional items may be changed or may not be provided depending on the computer model a Before You Start Before reading the User Guide first check the following information Optional items some devices and software referred to in the User Guide may not be provided and or changed by upgrade Q Note that the computer environment referred in the User Guide may not
7. Click Manage Network Connections from the left pane Select Internet Protocol Version 4 TCP IPv4 Configure the IP settings from the Networking tab and click Properties When using DHCP select Obtain an IP address automatically To use a static IP address select Use the following IP address and set the IP address manually Local Area Connection Properties Connect using Internet Protocol Version ACT CP IPv4 Properties EEEE EEEE EERI You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator This connection uses the following items for the appropriate IP settings Ii Client for Microsoft Networks cee ee i dEl QoS Packet Scheduler ee eee File and Printer Sharing for Microsoft Networks ee a Intemet Protocol Version 6 TCP IP v6 IP address H Intemet Protocol Version 4 TCP IPv4 ieee wi Link Layer Topology Discovery Mapper 1 0 Driver Link Layer Topology Discovery Responder Default gateway Obtain DNS server address automatically Transmission Control Protocol Intemet Protocol The default wide area network protocol that provides communication Alternate DNS server across diverse interct i Preferred DNS server Validate settings upon exit j T a may Aee eRe ON you Q When not using DHCP ask your network administrator sop Seeger for the IP address To add a network component click Install in the screen shown in t
8. E g For 1GB 1 024MB memory installed Windows may report the capacity as 1 022MB or less Recovery Solution Representation Optional Q What is a Recovery Area A Samsung computers have an additional partition to recover computers or save backup files Only for models with the Samsung Recovery Solution This partition is called a Recovery Area and it includes a recovery image that comprises of the OS and application programs You can either double click the Samsung Recovery Solution icon on the desktop or press F4 while booting the computer to enter the Recovery Area Then you can back up the present computer state or recover the computer from backed up images For deleting the Recovery Area you need to use an additional Recovery Area Removal Tool After deleting the recovery area you can use the newly created partition for other uses such as for saving personal data Be careful that once the recovery area is deleted the Samsung Recovery Solutions will not work anymore Q The capacity representation of the hard disk drive HDD in Windows is different from the product specifications A The capacity of the storage device HDD of the manufacturer is calculated assuming that 1KB 1 000 Bytes However the operating system Windows calculates the storage device capacity assuming that 1KB 1 024 Bytes and therefore the capacity representation of the HDD in Windows is smaller than the actual capacity This is due to the differ
9. Using Window in Dual View Click on the window title bar of the main LCD monitor number 1 and drag it into the auxiliary display device monitor number 2 to move the window Canceling Dual View 1 2 Click the Start gt Control Panel gt Appearance and Personalization gt Adjust screen resolution gt For Windows 7 Click the monitor number 2 icon and select Show Desktop on 1 only in the Multiple displays item Click the Apply button and then the OK button g J GH Daplay Screen Resolution p Change the appearance of your displays Onplay 2 Gener Non PnP Monitor x Multiple displays f Show desktop only onl v A You must select Apply before malang additional changes gt For Windows Vista Click on the Monitor Number 2 icon unselect Extend the desktop onto this monitor and then click Apply l Adjusting the Volume You can adjust the volume using the keyboard and the volume control program Since these descriptions are written on the basis of the latest operating system Windows 7 some of the content and the figures Q of the descriptions may differ depending on the operating system Since the procedures for other Windows operating systems are similar use the computer referring to these descriptions Adjusting the Volume using the Keyboard Alternatively right click over the Volume icon J and select Open Volume Mixer to adjust the volume Pre
10. When I connect a projector and change the settings to display the screen image on both the combination this is because the current resolution is too high and is not supported by the projector In this case change the resolution to 1024x768 pixels When I connect a projector the taskbar at the bottom of the screen is not displayed on the projector This occurs because a WXGA LCD supports a resolution of 1280x800 pixels but the resolution is not supported by the projector In this case change the resolution to 1024x768 pixels recommended The shortcut icons are not displayed on the screen even if press the shortcut key The shortcut icons only appear when the Easy Display Manager program is installed have connected a monitor or projector to the computer but the colors on the monitor are abnormally displayed Check if the monitor and computer are properly connected with the signal cable and reconnect the cable if necessary I am trying to view the screen through a TV by connecting it through the HDMI port but the edge of the screen is not displayed It is recommended using a notebook computer screen or monitor for documents and Internet pages Although connecting via the HDMI port is recommended when watching video it may be inappropriate for displaying documents and Internet pages because most TVs that support HDMI fail to display the edge of the screen or the characters on the screen properly cann
11. es da Directiva 1999 5 CE 37 Slovensko Slovenian Slovensky Slovak Suomi Finnish Svenska Swedish islenska Icelandic Norsk Norwegian Turkiye T rk e Samsung izjavlja da je ta Notebook PC v skladu z bistvenimi zahtevami in ostalimi relevantnimi dolo ili direktive 1999 5 ES Samsung t mto vyhlasuje e Notebook PC sp a z kladn po iadavky a v etky pr slu n ustanovenia Smernice 1999 5 ES Samsung vakuuttaa t ten ett Notebook PC tyyppinen laite on direktiivin 1999 5 EY oleellisten vaatimusten ja sit koskevien direktiivin muiden ehtojen mukainen H rmed intygar Samsung att denna Notebook PC st r verensst mmelse med de v sentliga egenskapskrav och vriga relevanta best mmelser som framg r av direktiv 1999 5 EG H r me l sir Samsung yfir v a Notebook PC er i samr mi vi grunnkr fur og a rar kr fur sem ger ar eru i tilskipun 1999 5 EC Samsung erkl rer herved at utstyret Notebook PC er i samsvar med de grunnleggende krav og vrige relevante krav i direktiv 1999 5 EF Bu belge ile Samsung bu Notebook PC nin 1999 5 EC Y netmeli inin temel gerekliliklerine ve ilgili h k mlerine uygun oldu unu beyan eder To view the EU Declaration of Conformity for this product in English only go to http www samsung com uk support download supportDownMain do then search the model number of the product If the Declaration of Conformity for the model you are interested in
12. Down Keys Press to move up and down F5 F6 Press to change the item value F9 Press to load the default Setup settings ESC Press to return to a higher level menu or to move to the Exit menu Left amp Right Keys Press to move to another menu Enter Press to select an item or to enter a sub menu F10 Press to save the changes and exit Setup The keyboard image may differ from the actual keyboard Setting a Boot Password When setting a password you have to enter a password to use the computer or enter the BIOS Setup By configuring a password you can restrict system access to authorized users only and protect data and files saved on the computer Q Before You Start Do not lose or forget your password If you have forgotten your password contact a Samsung service center In this case a service fee will be charged Setting a Supervisor Password 3 Enter a password press lt Enter gt re enter the e password for confirmation and press lt Enter gt again A Supervisor Password is required to turn the computer The password can be up to 8 alphanumeric on or to start the System Setup characters Special characters are not allowed When setting a Supervisor Password users other than a supervisor cannot use the computer i Set Supervisor Password Enter New Password I Confirm New Password I 1 Select the Security menu in the BIOS Setup In the Set Supervisor Password item press lt E
13. ME THN MAPOYZA Samsung AHAQNEI OTI Notebook PC 2YMMOP ONETAI MPO TIz OYZIOAEI2Z ANAITHZEI2 KAI TI AOINE2 2XETIKE2 AIATA El2 TH OAHTIA 1999 5 EK Par la pr sente Samsung d clare que l appareil Notebook PC est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999 5 CE Con la presente Samsung dichiara che questo Notebook PC conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999 5 CE Ar o Samsung deklar ka Notebook PC atbilst Direkt vas 1999 5 EK b tiskaj m pras b m un citiem ar to saist tajiem noteikumiem iuo Samsung deklaruoja kad is Notebook PC atitinka esminius reikalavimus ir kitas 1999 5 EB Direktyvos nuostatas Hierbij verklaart Samsung dat het toestel Notebook PC in overeenstemming is met de essenti le eisen en de andere relevante bepalingen van richtlijn 1999 5 EG Hawnhekk Samsung jiddikjara li dan Notebook PC jikkonforma mal ti ijiet essenzjali u ma provvedimenti o rajn relevanti li hemm fid Dirrettiva 1999 5 EC Alul rott Samsung nyilatkozom hogy a Notebook PC megfelel a vonatkoz alapvet6 k vetelm nyeknek s az 1999 5 EC ir nyelv egy b eldirasainak Niniejszym Samsung o wiadcza Se Notebook PC jest zgodny z zasadniczymi wymogami oraz pozosta ymi stosownymi postanowieniami Dyrektywy 1999 5 EC Samsung declara que este Notebook PC est conforme com os requisitos essenciais e outras disposi
14. digital unlike VHS analog video and supports MPEG2 compression and digital audio To play a DVD a DVD drive is required 128 Firewall A security system used to protect an internal network or intranet from external networks through an authentication procedure Hibernation Mode A power mode that saves all data in memory to the hard disk and turns the CPU and hard disk off When canceling Hibernation Mode all application programs that were running are restored to their last state Icon This refers to a small image that represents a file that users Can use LAN Local Area Network A communications network connecting computers printers and other devices within a local area such as within a building A LAN enables all connected devices to interact with other devices on the network The current LAN uses the Ethernet media access control method developed in the early 1980s To connect to an Ethernet a network card called a LAN card Ethernet card or network interface card is required To exchange data between computers a protocol is required besides the hardware equipment Windows Vista uses TCP IP as the default protocol LCD Liquid Crystal Display There are Passive Matrix and Active Matrix LCD types This computer uses the Active Matrix type LCD called a TFT LCD Since an LCD is implemented by transistors instead of a cathode ray tube unlike a CRT its size can be slim And because it does not blink it reduces eye
15. strain Network A group of computers and devices such as printers and scanners connected by a communications link A network can be either small or large and can be connected permanently through cables or temporarily through telephone lines or wireless links The biggest network is the Internet a worldwide network Network Administrator A user who plans configures and manages network operations Sometimes a network administrator is called a system administrator Notification Area This refers to the right area of the Taskbar including program icons such as the volume control the power options and the time 129 Quick Launch This refers to a toolbar that can be configured so that you can launch a program such as Internet Explorer or display the Windows Desktop with one click You can add any icon to the quick launch area of the Taskbar and launch frequently used program by clicking that Icon Server In general a server refers to a computer that provides shared resources for network users Share This refers to setting a resource of a computer such as a folder or printer so that other users can also use it Shared Folder A folder that can be used by other users on the network Sleep Mode A power mode that enables computers to save power consumption when they are not being used When a computer is in Sleep Mode the data on the computer memory is not saved to the hard disk If the power is turned off the
16. Complete Backup in progress Caution Make sure to connect the power while the backup is performed If the power is turned off during a backup you have to restart the backup from the beginning When the Restart the System message appears after the backup is complete click OK to restart the system Complete Restore 1 When backing up onto DVD Turn the computer on and insert the backup DVD into the DVD drive If there are multiple backup DVDs insert the first DVD When backing up to another drive Proceed to Step 2 Click Start gt All Programs gt Samsung gt Samsung Recovery Solution gt Samsung Recovery Solution When you cannot start Windows turn the computer NI on and press the F4 key in the boot screen to enter restoration mode 3 When the initial menu screen appears click Restore and then click Complete Restore 4 Select a Complete Backup restoration point in the restoration point selection screen and click the Next button The system is restarted i A Samsung Recovery Solution Samsung Recovery Solution 4 Home gt Restore gt Complete Restore Restores the entire C drive to the initial or backup status of the computer All current data on drive C is removed and the data will be restored at the time selected below You may need to reinstall some software after the Restore Select a Restore time and click the Next button 07 04 2009 My games and progr
17. HDMI or LCD HDMI Clone or LCD HDMI DualView mode using the Shortcut Key Fn F4 To listen to sound on the computer after disconnecting the HDMI TV you have to set the Playback Device to Speakers Using Dual View Dual View enables users to expand their computer screen over two display devices Dual View is convenient when a wide operating space is needed In addition since Dual View operates as if there are 2 graphic cards present even when there is only one you can set the resolution and color for each display device Since these descriptions are written on the basis of the latest operating system Windows 7 some of the content and the N figures of the descriptions may differ depending on the operating system Since the procedures for other Windows operating systems are similar use the computer referring to these descriptions Due to restrictions of the operating system the DualView function is not supported for Windows 7 Starter Selecting Dual View gt For Windows Vista Click on the number 2 monitor icon and select Check if the external display device is properly connected Extend the desktop onto this monitor Click and follow the instructions below Apply and then click the OK button Display Settings 1 Click the Start gt Control Panel gt Appearance and Personalization gt Adjust screen resolution Monitor Drag the icons to match your monitors Identify Monitors gt For Windows 7 Click
18. Other Function Keys Application Key Performs the right click mouse function touchpad To eject a CD f F Insert Press the Fn key combination to eject a CD The Fn a key combination does not work while Windows is booting up 1 Touchpad The touchpad provides the same function as a mouse and the left and right buttons of the touchpad plays the role of the left and right buttons of a mouse Q Before You Start Use the Touchpad with your fingers Using a sharp object may damage the Touchpad f you touch the Touchpad or press the Touchpad buttons while booting up the Windows boot time may be extended Touchpad Scroll Area Plays the role of the mouse wheel You can scroll up and down using the Scroll Area Use to move the cursor Touchpad Left Button You can select or run a program using this button Touchpad Right Button Plays the role of the right mouse button Basic Touchpad Functions Moving the cursor on the screen Click Function Place your finger on the touchpad slightly and move your Place your finger on the touchpad and tap your finger finger once over an item you want The mouse cursor will move accordingly Move your finger Alternatively press the left touchpad button once in the direction you wish to move the cursor Double Click Function Put your finger on the touchpad and quickly tap twice with your finger on an item you want Alternati
19. See 802 11b and 802 11g restrictions for specific EU R amp TTE Compliance Statements g T T it EE AAARAR AB EEE Cesky Czech Dansk Danish Deutsch German Eesti Estonian English Espanol Spanish EAAnVIKh Greek Fran ais French Italiano Italian Latviski Latvian Lietuvi Lithuanian Nederlands Dutch Malti Maltese Magyar Hungarian Polski Polish Portugu s Portuguese Samsung t mto prohla uje ze tento Notebook PC je ve shod se z kladn mi po adavky a dal mi p slu n mi ustanoven mi sm rnice 1999 5 ES Undertegnede Samsung erkl rer herved at f lgende udstyr Notebook PC overholder de v sentlige krav og vrige relevante krav i direktiv 1999 5 EF Hiermit erkl rt Samsung dass sich das Ger t Notebook PC in bereinstimmung mit den grundlegenden Anforderungen und den brigen einschl gigen Bestimmungen der Richtlinie 1999 5 EG befindet K esolevaga kinnitab Samsung seadme Notebook PC vastavust direktiivi 1999 5 EU p hin uetele ja nimetatud direktiivist tulenevatele teistele asjakohastele s tetele Hereby Samsung declares that this Notebook PC is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC Por medio de la presente Samsung declara que el Notebook PC cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999 5 CE
20. above computer To remove a card Click the Safely Remove Hardware icon on the task bar Click Remove ExpressCard You can remove the express card when the Safely Remove Hardware message appears ExpressCard Slot If you insert a card into the slot Windows recognizes the card automatically or a message telling you to install a driver appears If the card is not automatically recognized install the device driver supplied with the card Push the card in the slot lightly Then the card pops up Eject the card 1 2 3 4 D l Connecting a monitor TV Using an external display device is useful when you are giving a presentation or watching a video or movie through your monitor Q Before You Start You have to buy a connection cable additionally Due to restrictions of the operating system the DualView function is not supported for Windows 7 Starter Connecting to the Monitor TV Connecting to the Monitor port Connect the computer to the RGB port of the monitor or TV using a monitor cable 15 pin Connecting to the HDMI port Optional Connect the computer to the HDMI port of the monitor or TV using a HDMI cable When connecting the computer to a TV switch the external input mode of the TV to HDMI When a TV provides more than one HDMI port connect the computer to the DVI IN port Viewing Through a Monitor TV You can switch the display device us
21. appears If you register Windows according to the instructions on the screen the computer will be restarted When the Initial Status Backup is complete restart Windows After the computer has been restarted the Partition Setup screen appears To resize the C and D drives adjust the partition size using the slide bar and the click Next The Partition Setup function is only available when Q the computer is turned on for the first time and will not be available afterwards Once you have completed the partitioning it cannot be resized Partition the disk carefully Restoring the computer If the initial menu screen appears click Restore Restore is a function that enables restoring the computer rs to a saved point when the computer was purchased or a j d oamsung user saved point Recovery Solution 4 The Restore function provides the Basic Restore and Home Co m plete Re sto re o pti Ons Samsung Recovery Solution is a program that backs up the current status of the computer and restores the computer hard disk drive when a problem occurs Select by Symptom 1 When Windows is running Click Start gt All Programs gt Samsung gt gt Samsung Recovery Solution gt Samsung cA VF n Recovery Solution Backup system Software To view a brief description of an icon move the cursor over the icon If you need help click on Select by Symptom When Windows does not start Turn the computer on an
22. click the Next button Backup Point 07 04 2009 Backup Capacity 5 1GB Description My games and programs install complete Save Path Local Disk 76 6GB Available Local Disk 76 6GB Available E DVD Drive Select Drive D Select the DVD drive If you click the Next button the system restarts in restoration mode and the Complete Backup begins If you have selected the DVD drive as the Save Path the Insert a blank DVD message appears Insert a blank DVD and click the OK button Samsung Recovery Solution 4 To continue the backup a blank DVD is required Confirm that the DVD surface is clean and then insert the DVD Samsung Recovery Solution supports DVD R DVD R DVD RW and DVD RW but does not support CD R CD RW DVD RAM DVD DL Dual Layer HD DVD and Blu Ray 6 The Complete Backup begins If multiple DVDs are required the expected number of DVDs is displayed in the progress screen Whenever burning a DVD is completed the Insert the next DVD message will appear Continue the backup according to the instructions Samsung Recovery Solution 4 4 Samsung Recovery Solution 4 Home gt Backup gt Complete Backup Complete Backup in progress The required time is determined by the amount of data to be backed up Please wait until the backup is completed Burning DVD 1 Expected number of DVDs 1 Speed 9 4MB sec z 88 9 188MB Elapsed 09 13 55 49
23. data in memory will be lost System File system Files refer to files that are read and used by the Windows operating system In general system files must not be deleted or moved USB Universal Serial Bus This refers to a serial interface standard developed to replace the conventional interface standards such as Serial and PS 2 While USB 1 1 supports 12Mbps 12 million bits per second USB 2 0 supports a data rate that is 40 times 480Mpbs faster than that of USB 1 1 The data rate of USB 2 0 is equivalent to that of IEEE1394 Therefore USB 2 0 is used for A V devices supported by IEEE 1394 and a 2nd HDD and CDRW that require a high data rate Virtual XP Mode This is a virtual operating system that enables running Windows XP programs on the Windows 7 operating system Using this mode you can run programs that do not run on Windows 7 Windows Media Player A multimedia program included with Windows Using this program you can play a media file create an audio CD listen to a radio broadcast search and manage media files and copy files to a portable device etc 130 Index B Battery Battery Calibration BIOS Setup Booting Priority C CD Drive Recording Charge Click Connect Output Monitor D Dual View E ExpressCard Slot 90 93 82 87 58 91 53 64 70 63 L LCD Brightness Memory Multi Card Slot P Password Product Name Product Specifications R Recorder Rema
24. down the computer Connect To l Switch User Control Panel Log Off p Lock n Solitaire Default Programs aft Restart Default Programs All Programs Help and Support Sleep Help and Support Start Search All Programs 1 Power Button 2 3 Using the Power button in Windows Vista For Windows Vista the Power button is set to power saving mode Therefore if you click Start gt Power button on the computer enters power saving mode Save all your data before clicking on Shut down To shut down the computer by clicking this icon refer to the descriptions for Setting up Start menu power button of the Control Panel If the system cannot be shut down due to a system error turn it off by pressing and holding the Power Button for a minimum of 4 seconds Please note that turning the computer off by this method may cause a system problem Thereafter when turning the computer back on the disk checking program may launch to check for and correct any disk errors Chapter 2 Using the computer Keyboard Touchpad Basic Touchpad Functions The Gesture Function of the Touchpad Optional Touchpad On Off Function CD Drive ODD Optional Inserting and Ejecting a CD Multi Card Slot Optional ExpressCard Slot Optional Connecting a monitor TV Connecting to the Monitor TV Viewing Through a Monitor TV Using Dual View Adjusting the Volume Wired Network Wireless Ne
25. it is recommended entering the network key encryption key manually A7 Check the AP settings as follows The following is recommended for a standard environment and thus may differ according to the specific wireless network environment When several APs are present simultaneously check the channel settings for each AP When different APs are using nearby channels interference may occur between the electronic waves Set the AP channels further apart from each other Ex Ch1 Ch5 Ch9 Ch13 When an AP s SSID Service Set ID option is set to Hide you cannot search for that AP on the computer We recommend unselecting the Hide option for the AP The SSID is a name used for distinguishing one wireless LAN from another wireless LAN It is recommended using Long Preamble Preamble is a signal for data transmission synchronization Short Preamble may be supported by some types of APs but may cause compatibility problems It is recommended using a static IP Since static channel selection is more reliable than auto channel selection it is recommended using a static channel cannot connect to a computer connected to the Ad Hoc network A1 Check the security settings and network name of the wireless Ad Hoc network A2 Check the TCP IP settings of the computers connected to the wireless Ad Hoc network The IP addresses of the computers to be connected to a wireless Ad Hoc network must be set to the s
26. keyboard touchpad or mouse with excessive force It is recommended connecting an external keyboard and mouse when using the computer for long periods of time Volume Control Headphones and Speakers Check your volume first to listen to music VOLUME EZ Check your volume Check if the volume is too loud before using headphones itis not recommended using headphones for long periods of time Any deviation from the equalizer default setting could cause hearing impairment The default setting can be changed through software and driver updates without your intervention Please check the equalizer default setting before first usage 23 Use Time Break Time Take a break for 10 minutes or more after a 50 minute period when working for more than one hour Illumination Do not use the computer in dark locations The illumination level for computer use must be as bright so for reading a book Indirect illumination is recommended Use a curtain to prevent reflection on the LCD screen Operation Condition Do not use the computer in hot and humid locations Use the computer within the allowed temperature and humidity range specified in the User Guide Important Safety Information Safety Instructions Your system is designed and tested to meet the latest Openings in the computer case are provided for standards for safety of information technology equipment ventilation Do not bl
27. occurs because the algorithm used to remove the echo sound regards some of the sound as an echo and removes this as the recording is done by playing the sound from the external microphone After selecting the Acoustic Echo Cancellation option please select the Play Device gt Speaker gt Level tab and select Mute for the Microphone for a normal recording Wired Network LAN Related 0 The lt Wake On LAN gt function A lt Wake On LAN gt is a function that activates the system from Sleep mode when a signal such as a ping or magic packet command arrives over the network wired LAN Using the lt Wake On LAN gt Function gt For Windows 7 Click Start gt Control Panel gt Network and Internet gt Network and Sharing Center and click on Change adapter settings in the left menu pane gt For Windows Vista Click Start gt Control Panel gt Network and Internet gt Network and Sharing Center and click Manage Network Connections in the left pane Right click on the Local Area Connection and select Properties Click Configure gt Power Management tab Select Allow this device to bring the computer out of standby then click OK Restart the system If the system wake up from Sleep mode even though there is no received signal use the system after disabling the lt Wake On LAN gt function The LAN LED may not be turned off if System is shutdown without disabling the WOL Wake on LAN option
28. of the program Reinstalling Windows 7 Vista For Windows 7 and Windows Vista For supported models only You can reinstall Windows using the SYSTEM RECOVERY MEDIA for Windows when Windows is no longer working properly For models supplied with a SYSTEM RECOVERY MEDIA For models supplied with the Samsung Recovery Solution you can reinstall Windows using the Samsung Recovery Solution These descriptions are for Windows 7 and Windows Vista and for supported models only Q Before You Start A SYSTEM RECOVERY MEDIA may not be supplied depending on your computer model f you cannot start Windows or if you want to delete all existing data and reinstall Windows install Windows according to the descriptions in Reinstalling when Windows does not start Some pictures may differ from actual product These descriptions may differ depending on the operating system KH Reinstalling Windows may delete data files and programs saved on the hard disk drive Make sure to backup all important data Samsung Electronics shall not be held liable for any loss of data Reinstalling in Windows 1 i AutoPlay Insert the SYSTEM RECOVERY MEDIA into the DVD drive al DVD RW Drive D LRMCFRE_KO_DVD E Always do this for software and games When the AutoPlay window appears select Run setup exe and click Allow m Ear e n General options k Open folder to view files a riore gt k at imat de ee Set AutoPlay defau
29. outdoors is subject to licensing Wireless devices are not user serviceable Do not modify them in any way Modification to a wireless device will void the authorization to use it Contact manufacturer for service Telecommunications per DOC notice for products fitted with an IC compliant modem The Industry Canada label identifies certified equipment This certification means that the equipment meets certain telecommunications network protective operation and safety requirements The Department does not guarantee the equipment will operate to the users satisfaction Before installing this equipment users should make sure that it is permissible to be connected to the facilities of the local telecommunications company The equipment must also be installed using an acceptable method of connection In some cases the inside wiring associated with a single line individual service may be extended by means of a certified connector assembly The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations 35 Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier Any repairs or alterations made by the user to this equipment or equipment malfunctions may give the telecommunications company cause to request the user to disconnect the equipment Users should make sure for their own protection that t
30. product may increase during normal operation This may result in harming or burning your skin A Warning Failing to follow instructions marked with this symbol may cause personal injury and even fatality Upgrade Related er Never disassemble the power Use only authorized parts multi supply or AC adapter plug battery and memory and There is a danger of electric shock never disassemble parts There is a danger of damaging the product electric shock or fire hazard When removing the RTC Real Time Clock battery keep it out of the reach of children as they could touch and or swallow it There is a danger of choking If a child has swallowed it contact a doctor immediately 14 Shut down the computer and disconnect all cables before disassembling the computer If there is a modem disconnect the phone line If you are disassembling notebook computer make sure to remove the battery Failing to do so may cause electric shock A Warning Failing to follow instructions marked with this symbol may cause personal injury and even fatality Custody and Movement Related Follow the instructions for the relevant location e g airplane hospital etc when using a wireless communication device wireless LAN Bluetooth etc When carrying the notebook computer with other items such as the adapter mouse books etc take care not to press anything against the notebook computer
31. technical specifications of the devices If any smell of burning or smoke is detected from the computer the unit should be switched off and battery removed The unit should be checked by a qualified technician before reuse Service and repair of devices should be carried out by authorized service centers Do not allow your portable computer to operate with the base resting directly on exposed skin for extended periods of time The surface temperature of the base will rise during normal operation particularly when AC Power is present Allowing sustained contact with exposed skin can cause discomfort or eventually a burn I Replacement Parts and Accessories Use only replacement parts and accessories recommended by manufacturer T To reduce the risk of fire use only No 26 AWG or larger telecommunications line cord Do not use this product in areas classified as hazardous Such areas include patient care areas of medical and dental facilities oxygen rich environments or industrial areas Battery Disposal Laser Safety All systems equipped with CD or DVD drives comply with the appropriate safety standards including IEC 60825 1 The laser devices in these components are classified as Class 1 Laser Products under a US Department of Health and Human Services DHHS Radiation Do not put rechargeable batteries or products powered by non removable rechargeable batteries in the garbage Contact the Samsung
32. the down key to move to the AHCI HDD itemand press the F6 key to move up to the top item Press lt Enter gt on the Boot Device Priority item Boot Device Priority Boot priority order 1 AHCI CD N A 2 AHCI HDD XXXXXXXXXXXXXXXX XXXXXXXX SecureCore tm Setup Utility 3 USB KEY N A Main Advanced Security Boot Exit 4 USB CD XXXXXXXXXXXXXX 5 USB FDD N A Iti 6 USB HDD N A NumLock Off a 8 Summary screen Disabled pi Boot time Diagnostic Screen Disabled Excluded from boot order PRE OPROM Only with F12 pe er IDEHDD N A Brightness Mode Control Auto IDE CD N A Wireless Device Control Always On PCI SCSI N A Smart Battery Calibration USB ZIP N A USB LS120 N A Press the F10 key to save the settings and exit Setup The highest boot priority device is now set to the Hard Drive Upgrading Memory One or more memory modules are installed on the computer There are 2 memory slots and users can replace the installed memory or add new memory Q Before You Start Replace or install new memory only after shutting the computer down completely Do not replace or install memory when the computer is in Sleep mode Disconnect main power plug and remove the battery before continuing To utilize the dual channel feature using memory modules with the same specifications of the same capacity and from the same manufacturer is recommended Only use the same type of memor
33. them through your local free battery return system USA ONLY This Perchlorate warning applies only to primary CR Maganese Dioxide Lithium coin cells in the product sold or distributed ONLY in California USA Perchlorate Material special handling may apply See www dtsc ca gov hazardouswaste perchlorate Contains Mercury Dispose According to Local State or Federal Laws For details see lamprecycle org eise org or call 1 800 Samsung 40 I Overview Q Before You Start Optional items may be changed or may not be provided depending on the computer model F Vi The actual color and appearance of the computer ront View may differ from the pictures used in this guide CO NIO Q A OIN Camera Lens Optional Microphone Optional Power Button Keyboard Touchpad Touchpad Buttons Multi Card Slot sa Optional Status Indicators LCD SAMSUNG NO Using this lens you can take still pictures and record video You can use the built in microphone Turns the computer on and off A device to enter data by pressing the keys The touchpad and touchpad buttons provide functions similar to the mouse ball and buttons A card slot that supports SD Card SDHC MMC and xD cards Shows the operating status of the computer The corresponding operating LED is lit wnen the corresponding function operates The screen images are displayed here T 41 Status Indicators N Oo 0 A Q Num L
34. to this port 3 Monitor Port Optional A port used to connect a monitor TV or projector supporting a 15pin D SUB interface 4 Chargeable USB Port e 4 You can connect USB devices to the USB port such as a keyboard mouse digital camera Optional etc Chargeable USB You can charge USB devices through the USB port even when the computer is turned off Charging a device through a Chargeable USB takes longer than using a regular charger Press the F2 key when the Samsung logo appears in the booting sequence to enter the BIOS Setup select Advanced gt USB Charge In Sleep Mode and set it to Enable Then you can use the Chargeable USB Port feature even in sleep mode 5 eSATA USB Common Port This port can be used to connect a USB or eSATA device Optional 6 Digital Video Audio Port You can connect an HDMI cable to this port HDMI Optional Using this port you can enjoy digital video and audio on the TV Microphone Jack A A jack used to connect the microphone 8 Headphone Jack A jack used to connect the headphones a 9 ExpressCard Slot Optional Install the Express card into this slot es 44 1 Battery This is a Lithium lon rechargeable battery that supplies power to the computer 2 Fan Vents The internal heat of the computer is emitted through these holes RE If the vents are blocked the computer may overheat Avoid blocking the vents as this may be dangerous Bottom View 1 Battery Latch
35. 20 Windows 7 fanl H Currently connected to COM AV SWL3300 B24 af Access Local only ani Cel 10 07 Windows Vista Chapter 3 Settings and Upgrade LCD Brightness Control BIOS Setup Entering the BIOS Setup The BIOS Setup Screen Setting a Boot Password Changing the Boot Priority Upgrading Memory Battery Installing Removing the Battery Charging the Battery Measuring the Remaining Battery Charge Extending the Battery Usage Time Using the Security Lock Port 81 82 82 83 85 87 88 90 90 91 92 95 94 LCD Brightness Control You can adjust the LCD brightness in 8 levels Q Before You Start The screen brightness is automatically set to the brightest level brightness level 8 when AC power is connected and the brightness is automatically set dimmer when the computer runs on battery power to extend the battery use time Controlling the Brightness Using the Keyboard Adjust the LCD brightness by pressing the Fn key or the Fn The LCD brightness can change up to 8 levels and the brightness increases by 1 level when pressing the Fn key once a To maintain the LCD brightness set by using the brightness control keys or through the Power Options follow the procedures below 1 Turn the computer on and press the F2 key when the SAMSUNG logo appears on the screen to enter the BIOS Setup Maintaining the changed LCD brightness even after tur
36. 8 inches separation between the device and the body for use of a wireless device near the body this does not include extremities This device should be used more than 20 cm 8 inches from the body when wireless devices are on The power output of the wireless device or devices which may be embedded in your notebook is well below the RF exposure limits as set by the FCC This transmitter must not be collocated or operate in conjunction with any other antenna or transmitter except the installed Bluetooth transmitter Operation of this device is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation of the device 32 Wireless devices are not user serviceable Do not modify them in any way Modification to a wireless device will void the authorization to use it Contact manufacturer for service FCC Statement for Wireless LAN use While installing and operating this transmitter and antenna combination the radio frequency exposure limit of imW cm2 may be exceeded at distances close to the antenna installed Therefore the user must maintain a minimum distance of 20cm from the antenna at all times This device can not be colocated with another transmitter and transmitting antenna FCC Part 68 If fitted with a modem device This equipment compiles with part
37. Helpline for information on how to dispose of batteries that you cannot use or recharge any longer Follow all local regulations when disposing of old batteries THERE IS A RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS 26 Performance Standard Should the unit ever need servicing contact an authorized service location Laser Safety Note Use of controls or adjustments or performance of procedures other than those specified in this manual may result in hazardous radiation exposure To prevent exposure to laser beams do not try to open the enclosure of a CD or DVD drive Class 1M laser radiation when operating part is open Do not view directly with optical instruments Class 3B invisible laser radiation when open Avoid exposure to the beam Connect and Disconnect the AC adapter The socket outlet shall be installed near the equipment and shall be easily accessible Do not unplug the power cord out by pulling the cable only Power Cord Requirements The power cord set wall plug cable and AC adapter plug you received with your computer meets the requirements for use in the country where you purchased your equipment Power cord sets for use in other countries must meet the requirements of the country where you use the computer For more information on power cord set requirements contact your authorized dealer reseller or se
38. Internet or when you cannot use Internet banking services For the Windows Vista operating system This symptom may appear when the User Account Control function is set in Windows Vista The User Account Control function enables the administrator to determine the program execution permission of user accounts and the function is set to Use by default in Windows Vista for security purposes Although your system is more protected from attack by malicious code if it is set to Use this symptom may continue Although this symptom will not appear again if it is N set to Do Not Use your computer may be exposed to attack from malicious code Click Start gt Control Panel gt User Accounts and Family Protection gt User Accounts gt Use or Do Not Use User Accounts Control Unselect the Protect the computer safer using User Accounts Control option and click the OK button The User Account Control will be set to Do Not Use and the windows will not appear again For the Windows 7 operating system In Windows 7 the frequency of the confirmation window that appears during the program installation or execution or after changing Windows settings is determined by the security level setting in the User Account Control This may occur when the security level in the User Account Control is set to Alarm always Click Start gt Control Panel gt User Accounts and Family Protection gt User Accounts gt Change User Accoun
39. MHz The low band 5 15 5 35 GHz is for indoor use only Belgium The product may be used outdoors but for outdoor transmissions over a distance of 300m or more a license from the BIPT is required This restriction should be indicated in the manual as follows Dans le cas d une utilisation priv e a l ext rieur d un b timent au dessus d un espace public aucun enregistrement nest n cessaire pour une distance de moins de 300m Pour une distance sup rieure a 300m un enregistrement aupr s de l IBPT est requise Pour une utilisation publique l ext rieur de b timents une licence de l IBPT est requise Pour les enregistrements et licences veuillez contacter l IBPT France For Metropolitan departments 2 400 2 4835 GHz for indoor use 2 400 2 454 GHz channels 1 to 7 for outdoor use For Guadeloupe Martinique St Pierre et Miquelon Mayotte 2 400 2 4835 GHz for indoor and outdoor use For Reunion Guyane 2 400 2 4835 GHz for indoor use 2 420 2 4835 GHz for outdoor use channels 5 to 13 The low band 5 15 5 35 GHz is for indoor use only 39 European Telecommunication Information for products fitted with EU approved modems Marking by the symbol CE indicates compliance of this equipment to the Radio and Telecom Terminal Equipment Directive 1999 5 EC Such marking is indicative that this equipment meets or exceeds the following technical standards CTR 21 Attachment requirements fo
40. Memory DRAM is a memory type whose cells consist of a capacitor and transistor manufactured at a low price SDRAM is a memory type whose performance has been improved by synchronizing the clock with the external CPU clock DDR SDRAM is a memory type whose performance has been improved by doubling the operating speed of the SDRAM and is widely used nowadays This computer uses DDR SDRAM Device Manager An administrative tool used to manage computer devices You can add or remove hardware or update a device driver using the Device Manager Direct X An application interface developed to enable Windows application programs to access hardware devices at a very high speed Since the operating speed of graphics memory and sound cards must be very fast to provide high quality video and sound for games Direct X enables faster control and interaction between applications and hardware devices By using Direct X the multimedia performance of Windows has been hugely improved Driver Software that interacts between the hardware and the operating system An operating system knows the hardware information and controls the hardware In general a driver is supplied with the corresponding hardware device DVD Digital Versatile Disk DVD was developed to replace CD compact disk Although the shape and size of the disc are the same as that of a CD the capacity of a DVD is at least 4 7GB while the capacity of a CD is 600MB DVD video is
41. P address to the client properly and the client station cannot connect to the network The AP network key can be configured using an AP management program For more detailed information ask your network administrator or product provider A3 Check that the device driver is installed properly If the driver is not properly installed you will find a yellow exclamation mark on the network icon by clicking Device Manager gt Network Adapter 0 I cannot connect to the AP Check the Computer Settings A1 Select Start gt All Programs gt Accessories gt Windows Mobile Center and check the wireless device status When it is represented as Disconnected This means the computer is not connected to the AP Check the status of the AP referring to the descriptions of the Checking the SP Settings section below Check the encryption key configured in the AP and retry to the connection When it is represented as Connected but you cannot connect to the Internet This means the computer is connected to the AP but the AP or external network connected with the AP may have a problem When the There is no wireless LAN adapter message appears or there is no wireless LAN icon This means the wireless LAN device is set to Do Not Use or the device is not recognized Check if the wireless device is properly recognized in the Device Manager window If the device is set to Do Not Use right click and select Use from the pop up me
42. Use checkbox on the left Click OK You will be able to experience a more stereophonic sound in the selected mode 3 Select the SRS tab in the Speaker Properties 9 Speakers Properties General Levels Enhancements SRS Advanced able SRS Technology Music SRS Sound SRS Center SRS Space TruBass Level TruBass Speaker Size 300Hz FOCUS Level SRS Definition 2009 SRS Labs Inc SRS TruBass Definition Dialog Clarity and FOCUS are trademarks or registered trademarks of SRS Labs Inc All rights reserved Music Select to listen to music WOW HD technology has been used Movie Select to watch a movie TruSurround XT technology has been used When using a Headphone plugged in the Headphone jack Some of the setting details under each menu will change CS Headphone technology has been used The SRS function is only supported for a computer s NI built in speakers or headphones itis recommended to unchecking the SRS option before recording and to check it before play It is to prevent sound distortion because of double application of SRS effect when user plays the file recorded by using stereo mix Wired Network A wired network is a network environment used for a company network or broadband internet connection at home of the descriptions may differ depending on the operating system Since the procedures for other Wind
43. act with metal objects such as car keys or clips when keeping or carrying a battery Contact with a metal may cause excessive current and a high temperature and may damage the battery or cause a fire Charge the battery according to the instructions in the manual Failing to do so may cause an explosion or fire from damage to the product Do not heat the battery or expose it to heat e g inside a vehicle during the summer There is a danger of explosion or fire AN Caution Usage Related Failing to follow instructions marked with this symbol may cause slight injury or damage to the product Do not place a candle light cigar etc over or on the product There is a danger of fire Use a wall outlet or multi plug with a grounding part Failing to do so may cause electric shock hazard Make sure to have the product tested by a safety service engineer after repairing the product Authorized Samsung Repair Centers will carry out safety checks after a repair Using a repaired product without testing it for safety may cause an electric shock or fire In case of lightning immediately turn the system off disconnect the power cord from the wall outlet and phone line from modem Do not use a modem or phone There is a danger of electric shock or fire Do not use your computer and AC Adapter on your lap or soft surfaces If the computer temperature increases there is a danger of burning yourself C
44. al or backup status of the computer All current data on drive C is removed and the data will be restored at the time selected below You may need to reinstall some software after the Restore Select a Restore time and click the Next button Select Backup Date Descrintion Expected Require Source 07 01 2009 Computer Initial Status 07 07 HDD Caution Make sure to connect the power for the Restore If the power is turned off during a Restore you have to restart the Restore from the beginning Since a Complete Restore deletes all user data as well as additionally installed programs please backup your important data first using the Data Backup function before running Complete Restore If the Samsung Recovery Solution program is launched for the first time after purchasing the computer the license agreement screen appears before the restoration is started Read the agreement and click Agree to continue The computer boots up into restoration mode and the restoration progress message appears If you click OK the restoration begins The restoration may take some time please wait for a moment after the restoration is complete click OK to restart 6 When the Restart the System message appears the system Make sure that the power cord is connected while the restoration is in process The first time the computer boots up after a Complete Restore has been performed the speed of the boot process may
45. ame sub network address For example if the TCP IP setting is configured to a fixed IP address select Use the following IP address in the TCP IP Properties of the wireless adapter configure the items as follows and try again IP 10 0 0 1 10 0 0 254 Subnet Mask 255 255 255 0 It is recommended using a fixed IP address for wireless Ad Hoc network connections A3 You have to register the IP address allocated for the wireless adapter as a Trusted IP in McAfee SecurityCenter Click McAfee SecurityCenter gt Advanced menu gt Configure gt Internet and Network gt Advanced gt Trusted and Banned IPs and register the IP address or IP address range as a Trusted IP address During the wireless Ad Hoc network operation the AP Access Point is intermittently not found This problem occurs intermittently during the wireless Ad Hoc network operation Even if this problem occurs the wireless Ad Hoc network operation is working properly and is not affected Click Refresh to update the AP list have set the same IP address for both the wireless and wired connections but they do not work properly You cannot use wireless and wired connections using the same IP address To sequentially use both the wired and wireless connections with the same IP address you need to set the currently not needed connection to Do Not Use in the Network Connections of the Control Panel A1 The wireless LAN does not work properl
46. ams install complete Caution Make sure to connect the power for the Restore If the power is turned off during a Restore you have to restart the Restore from the beginning The restoration progress message appears after the computer boots up in restoration mode If you click OK the restoration begins If multiple DVDs have been used for a Complete Backup whenever burning a DVD is completed the Insert the next DVD message will appear When the Restart the System message appears after the restoration is complete click OK to restart the system The Complete Restore has been completed Data Backup Restore Data Backup enables you to save specific files or folders onto another drive or DVD Data Restore enables you to restore data using the data saved by a Data Backup when data is lost This guide describes the Backup and Restore procedures on the basis of backing up and restoring by using DVD O Data Backup Click Start gt All Programs gt Samsung gt Samsung Recovery Solution gt Samsung Recovery Solution When you cannot start Windows turn the computer on and press the F4 key in the boot screen to enter restoration mode When the initial menu screen appears click Backup and then click Data Backup Selection or Select from all select a folder or file to be backed up and then click the Next button 3 In the data selection screen select either Basic A Enter a descripti
47. ancement purposes The BIOS Setup menus and items may differ depending on your computer model Entering the BIOS Setup 1 Turn the computer on Press the F12 key while the booting screen SAMSUNG N logo appears the system will try to boot from the network When the booting screen SAMSUNG logo appears press the F2 key to enter the BIOS Setup 3 After a moment the BIOS setup screen appears The items in the BIOS setup may differ depending on the product The BIOS Setup Screen Advanced Security Boot Exit Setup Menu Item Specific Help Help System Time 10 21 53 Help for the selected System Date 07 30 2004 lt Tab gt lt Shift Tab gt or item appears lt Enter selects field SATA Port 1 VUUUUUUY automatically SATA Port 2 AARRRRRR CPU Type RARARARA CPU Speed 4 8K GHZ Total Memory ARR MB Slot Memory nit MB Slot2 Memory RAR MB Graphics Memory Auto Shared BIOS Version HRAKRRRH Sei i MICOM Version HHRRRRAA etup Items Setup Menu Description Main Used to change the basic system and environment settings Advanced Used to configure advanced functions on your computer for devices and chipsets Security Used to configure security functions including passwords Boot Used to set the boot priority and other boot options Exit Used to exit the Setup either saving the changes or not System Setup Keys In the Setup you have to use the keyboard F1 Press to view the Setup Help Up amp
48. are Installation i a function that instals the required device drivers and applications Samsung Recovery Solution version 4 or later ee ag a aces Therefore the function may not be supported depending on the version System Software Installation System Software Backup EH The System Software Installation Function only works in Microsoft Windows This function installs the system software If a device or Samsung application does not work properly you can reinstall the required applications individually or all at the same time O Installing System Software Click Start gt All Programs gt Samsung gt Samsung Recovery Solution gt Samsung Recovery Solution When the Samsung System Software screen appears check all the device drivers and application programs you want to install and then click Install Now After the installation is complete the computer will restart System Software Backup A 1 Click Start gt All Programs gt Samsung gt Samsung Recovery Solution gt Samsung Recovery Solution When the initial menu screen appears click System Software gt System Software Backup If you click the Next button the Software Backup begins If you have selected the DVD drive as the Save Path the Insert a blank DVD message appears Insert a blank DVD and click the OK button After the backup the System Software Backup is completed message appears backed up on the drive run the Soft
49. ay make changes in its facilities equipment operations or procedures that could affect the operation of the equipment If this happens the telephone company will provide advanced notice in order for you to make necessary modifications to maintain uninterrupted service If trouble is experienced with this equipment Modem for repair or warranty information please contact your local distributor If the equipment is causing harm to the telephone network the telephone company may request that you disconnect the equipment until the problem is resolved The user must use the accessories and cables supplied by the manufacturer to get optimum performance from the product No repairs may be done by the customer This equipment cannot be used on public coin phone service provided by the telephone company Connection to party line service is subject to state tariffs The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device including fax machines to send any message unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission the date and time it is sent and an identification of the business or other entity or other individual sending the message and the telephone number of the sending machine or such business other entity or individual The telephone number provided may not be any number for w
50. be slowed down due to the system optimization process At this time do not shut the computer down by force Backup Function Complete Backup Restore A Complete Backup saves the complete image of the C drive onto another drive or DVD A Complete Restore restores the image file saved by the Complete Backup onto the C drive Complete Backup If you run Complete Backup using a DVD you can Q restore the computer even when a problem occurs with the hard disk or when the restoration area is removed 1 Click Start gt All Programs gt Samsung gt Samsung Recovery Solution gt Samsung Recovery Solution When the initial menu screen appears click Backup INO Click Complete Backup in the backup menu GO Enter a description for the backup regarding the current computer status in the Description field so that you can easily recognize it later and specify the Save Path If your computer has a DVD Writer you can specify the DVD drive as the Save Path m _ Samsung Recovery Solution Samsung Recovery Solution 4 Home gt Backup gt Complete Backup Backs up the current status of the C drive to the other drive a DVD or an external type storage device as an image You can easily restore your computer to the current status using the backup image when your computer does not work properly due to a virus infection or some other reason Enter a description for the backup image directly or select one and then
51. be the same as your own environment Images used in this User Guide may differ from actual product This guide decribes procedures for using both the mouse and the touchpad This manual has been written for the Windows operating system The descriptions and figures may differ depending on the installed operating system The User guide supplied with this computer may vary depending on your model Safety Precaution Notations Description Warning Failing to follow instructions marked with this symbol may cause personal injury and or fatality AN Cation Failing to follow instructions marked with this symbol may cause slight injury to yourself or damage your property Text Notations Before You Start Content included in this section includes information required before using a function Icon a Caution Content included in this section includes information required about the function Content included in this section includes helpful information to use the function Copyright 2009 Samsung Electronics Co Ltd Samsung Electronics Co Ltd owns the copyright of this manual No part of this manual may be reproduced or transmitted in any form or by any means electronic or mechanical without the consent of Samsung Electronics Co Ltd The information in this document is subject to change without notice due to improving the performance of the product Samsung Electronics shall not be liable for any da
52. bile satellite systems High power radar is allocated as the primary user of the 5 25 to 5 385 GHz and 5 65 to 5 85 GHz bands These radar stations can cause interference with and or damage to this device 34 The maximum allowed antenna gain for use with this device is 6dBi in order to comply with the E I R P limit for the 5 25 to 5 35 and 5 725 to 5 85 GHz frequency range in point to point operation As a general guideline a separation of 20 cm 8 inches between the wireless device and the body for use of a wireless device near the body this does not include extremities is typical This device should be used more than 20 cm 8 inches from the body when wireless devices are on The power output of the wireless device or devices which may be embedded in your notebook is well below the RF exposure limits as set by Industry Canada This transmitter must not be collocated or operate in conjunction with any other antenna or transmitter except the installed Bluetooth transmitter Operation of this device is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation of the device To prevent radio interference to licensed service this device is intended to be operated indoors and away from windows to provide maximum shielding Equipment or its transmit antenna that is installed
53. connected all Connections are available Wireless Network Connection R4 COM_19F Connect automatically ELBRUSAP9 Open Network and Sharing Center Y For the network key please ask your network administrator When Connected to the AP is displayed click the Close button You can access the network gt For Windows Vista Right click over the Network Connections icon on the taskbar and click Connect to the Network Connect to a network Turn on activity animation Turn off notification of new networks Diagnose and repair Network and Sharing Center Select an AP to connect to and click Connect If there is a configured network key for the AP to connect to the Enter Network Key window appears Enter the network key in the window and then click the Connect button Disconnect or connect to another network Show All th Security enabled network a SamsungWLAN Unsecured network x COM AV RG2000 G80 Security enabled network Set up a connection or network Open Network and Sharing Center Cancel Ask your network administrator for the network key if necessary When Connected to the AP is displayed click the Close button You can access the network Checking the network connection status Move the mouse pointer over the Wireless Network Connection pall icon on the taskbar and the connection status is displayed For Windows Vista mt AccessPoint Intemet access 10 32 F
54. d from another computer Press lt Enter gt in the Set HDD Password item and define a password as described in Step 3 of the Setting up the Supervisor Password The hard disk drive password setting function is not provided for some models Changing the hard disk drive password For security purposes you can only change a hard disk drive password after restarting the computer by pressing the computer Power button If you cannot change the hard disk drive password or the HDD Password Frozen message appears when entering the BIOS Setup and then selecting Security gt HDD Password press the Power button to turn the computer on again Deactivating the Password 1 or A WW N Press lt Enter gt on the password to be deactivated For example to deactivate a supervisor password in the Set Supervisor Password item press lt Enter gt In the Enter Current Password item enter the currently configured password and press lt Enter gt Leave the Enter New Password item field empty and press lt Enter gt Leave the Confirm New Password field empty and press lt Enter gt In the Setup Notice window press lt Enter gt The password is deactivated Changing the Boot Priority By default the highest boot priority device is set to the CD ROM DVD drive As an example the procedures to change the highest boot priority device to the hard disk drive are described below 1 Select the Boot menu in the BIOS Setup 3 Press
55. d press the F4 key when the boot screen SAMSUNG logo appears After a moment the computer boots up in Restoration mode and the Samsung Recovery Solution screen If you click Select by Symptom the Select by appears PP Symptom menu appears If you select a symptom a recommended restoration option will blink Click the restoration option to continue For computers supporting the touch screen function Y the touch screen function does not work during Restore Mode In this case please use the touchpad or mouse Select either Basic Restore or Complete Restore from the Restore menu A Basic Restore restores the major Windows files only while maintaining the user configuration and data on the C drive in a short time A Complete Restore deletes the entire C drive and then restores the contents of the C drive Run Complete Restore if the computer does not work even after Basic Restore has been completed 3 1 If you have selected Basic Restore In the Basic Restore screen click the Next button The system will be restarted 3 2 If you have selected Complete Restore 4 In the restoration point selection screen select the restoration point described as Computer Initial Status and click the Next button The system will be restarted E A Samsung Recovery Solution e xX Samsung i Recovery Solution 4 Home gt Restore gt Complete Restore Restores the entire C drive to the initi
56. dows to drive C is recommended Language Time Keyboard etc appear Confirm the settings and click the Next button A If you click Drive Options Advanced you can delete format create or expand a partition Click on a function and proceed according to the instructions on the screen A If the Select Windows Installation window When previous Windows installation files are in the appears click Install Now selected partition a message appears informing you that the files and folders will be moved to the Windows old folder Click the OK button For Windows 7 Vista the screen asking for the operating system to be installed may appear depending on the version If you click the Next button the screen of Step 5 appears PARR The subsequent steps are the same as those from Step 7 of Installing in Windows Q amp A This section provides information on possible problems solutions and other references for using the system Since these descriptions are written on the basis of the latest operating system Windows 7 some of the content and the N figures of the descriptions may differ depending on the operating system Since the procedures for other Windows operating systems are similar use the computer referring to these descriptions The path may differ depending on the operating system Windows Related When unwanted confirmation windows appear repeatedly while installing or running a program connecting to the
57. e 3D Settings Scheme Options Video Settings 3 Fit the Desktop to the TV screen by sliding the Horizontal and Vertical Resize Bars and click OK Aspect Ratio Options J Masimum Vertical J Maximum Intel Graphics Media Accelerator Driver intel for mobile LIE Cancel Resize Bars Setting up HDMI TV audio Optional You can configure the sound of the computer to be played through the HDMI TV You have to configure the sound device in the Control Panel whenever you connect the HDMI TV in order to hear sound from the computer on the TV The screen images and terms may differ from actual product depending on the computer model 1 Right click over the Volume Control icon in the notification area at the bottom right of the Desktop and select Playback Devices Alternatively click the Control Panel gt Hardware and Sound gt Sound 2 If the default Playback Device is set to Speakers change it to Digital Output Device HDMI or HDMI Device click Set Default and then click OK i Sound Playback Select a playback device below to modify its settings KAKA KAK 2 High Definition Audio Device Default Device Speakers Realtek High Definition Audio Ready Configure HDMI Output Device may not appear on the playback device list depending on the computer model In this case turn on the TV connect the TV to the computer using a HDMI cable and then switch to
58. e Celeron Processor Main Memory Optional Memory type DDR2 SODIMM Main Chipset Optional Intel GM45 PM45 ICH9M Hard Disk Drive Optional 9 5mmH SATA HDD nVIDIA N10M GE1 GeForce G 105M External Graphics Optional p Op Intel Internal Graphic GMA X4500 Internal i Temperature 5 40 C for storage 10 35 C when operating Operating Environment E l Humidity 5 90 for storage 20 80 when operating Operating Voltage 100 240VAC Frequency 50 60Hz Output Power Optional 60W or 90W Output Voltage Optional 19V 3 16A 60W 19V 4 74A 90W Optional components may not be provided or different components may be provided depending on the computer model The system specifications are subject to change without notice The hard disk drive capacity of a computer in which Samsung Recovery Solution is installed is represented as smaller than the product specification 126 Registered Trademarks ENERGY STAR Partner As an ENERGY STAR Partner SAMSUNG Samsung is a registered trademark of Samsung Co Ltd has determined that this product meets the Intel Pentium Celeron are registered trademarks of the ENERGY STAR guidelines for energy Intel Corporation Das efficiency Microsoft MS DOS and Windows are registered trademarks of the Microsoft Corporation ETCL S S is a trademark of SRS Labs Inc TruSurround XT technology is incorporated under license from SRS Labs Inc SRS TruSurround XT process
59. e may not be allowed The RF field strength of the wireless device or devices that may be embedded in your notebook are well below all international RF exposure limits as known at this time Because the wireless devices which may be embedded into your notebook emit less energy than is allowed in radio frequency safety standards and recommendations manufacturer believes these devices are safe for use Regardless of the power levels care should be taken to minimize human contact during normal operation As a general guideline a separation of 20 cm 8 inches between the wireless device and the body for use of a wireless device near the body this does not include extremities is typical This device should be used more than 20 cm 8 inches from the body when wireless devices are on and transmitting Some circumstances require restrictions on wireless devices Examples of common restrictions are listed on the next page 28 Radio frequency wireless communication can interfere with equipment on commercial aircraft Current aviation regulations require wireless devices to be turned off while traveling in an airplane 802 11ABGN also known as wireless Ethernet or Wifi and Bluetooth communication devices are examples of devices that provide wireless communication In environments where the risk of interference to other devices or services is harmful or perceived as harmful the option to use a wireless device may be restricted or eliminated Ai
60. e the battery pack Carefully read and follow the precautions printed on the battery and the safety instructions in the User Manual before using the battery Please refer to the system operation environment of this manual and operate and store the battery at room temperature Installing Removing the Battery 1 Shutdown the system close the LCD panel and place the computer upside down on a flat surface Pull the two battery latches outwards p f then remove the battery 3 To install the battery again slide the battery into the system The battery latches move inwards and fix the battery automatically w Check if the battery latch has been moved inwards Charging the Battery 1 Attach the battery and connect the AC adapter to the DC in jack of the computer The battery will then start charging When charging is complete the Charge LED turns green Status Charge LED Charging Amber Charging complete Green AC adapter not connected Off Measuring the Remaining Battery Charge You can view the battery charge status by completing the following procedures To use the shortcut key to view Press the Fn _ keys on the keyboard The remaining battery charge will displayed for a moment You can only view the charge status in this way when Easy Display Manager is installed on your computer Confirming the battery charge in the Taskbar Disconnect the AC adapter and move t
61. e work The heights are to be adjusted so that your arm forms a range where you can reach them with your hands right angle when you place your hand over the keyboard while sitting down on a chair Adjust the height of chair so that your heel is comfortably placed on the floor Do not use the computer while you are lying down but only while you are sitting down Do not use the computer on your lap If the computer temperature increases there is a danger of burning yourself Work while keeping your waist straight Use a chair with a comfortable back Keep the center of your leg weight not on the chair but on your feet when you are sitting on a chair 21 Eye Position Keep the monitor or LCD away from your eyes by at least 50cm Adjust the height of the monitor and the LCD screen so that its top height is equal to or lower than your eyes Avoid setting the monitor and LCD excessively bright Keep the monitor and LCD screen clean f you wear glasses clean them before using the computer When entering contents printed on a paper into the computer use a static paper holder so that the height of the paper is almost equal to that of the monitor 22 Hand Position Keep your arm at a right angle as shown by the figure Keep the line from your elbow to your hand straight Do not place your palm over the keyboard while typing Do not hold the mouse with excessive force Do not press the
62. eansing solution when cleaning the product and only use the computer when it is completely dried Failing to do so may cause electric shock or fire Emergency disk eject method using paperclip should not be used while the disk is in motion Make sure to use the emergency disk eject method only when the Optical Disk Drive is stopped There is a danger of injury Do not place your face close to the Optical Disk Drive tray when it is operating There is a danger of injury due to an abrupt ejection Check CDs for cracks and damage prior to use It may damage the disc and cause disorder of device and injury of user 18 AN Caution Failing to follow instructions marked with this symbol may cause slight injury or damage to the product Upgrade Related Take care when touching the product or parts The device may be damaged or you may be injured Take care not to throw or drop a computer part or device This may cause injury or damage to the product Make sure to close the computer cover before connecting the power after a reassembly There is a danger of electric shock if your body touches an internal part Use parts authorized by Samsung Electronics only Failing to do so may cause fire or damage the product Never disassemble or repair the product by yourself There is a danger of electric shock or fire To connect a device that is not manufactured or authorized by Samsung Electronics e
63. ence in capacity calculation and does not mean the installed HDD is different from the product specifications The capacity representation in Windows may be smaller than the actual capacity because some programs occupy a certain area of the HDD outside of Windows For models with Samsung Recovery Solution the HDD capacity representation in Windows may be smaller than the actual capacity because Samsung Recovery Solution uses a hidden area of about 5 20GB of the HDD to save the recovery image and that hidden area is not counted towards the total size available to Windows The size of Samsung Recovery Solution varies by models because of the different size of applied programs I Contents Chapter 1 Getting Started Chapter 3 Settings and Upgrade Product Features 2 LCD Brightness Control 81 Before You Start 3 BIOS Setup 82 Contents 6 Entering the BIOS Setup 82 Safety Precautions 7 The BIOS Setup Screen 83 Proper Posture During Computer Use 21 Setting a Boot Password 85 Important Safety Information 24 Changing the Boot Priority 87 Replacement Parts and Accessories 26 Upgrading Memory 88 Regulatory Compliance Statements 28 Battery 90 WEEE SYMBOL INFORMATION 40 Installing Removing the Battery 90 Overview 41 Charging the Battery 91 Front View 41 Measuring the Remaining Battery Charge 92 Status indicators 42 Extending the Battery Usage Time 93 Right View 43 Using the Security Lock Port 94 Left View 44 Back View 45 Bottom View 46 T
64. er Do not pull or push the disc by force when the disc depending on the condition and type of the media tv is being automatically ejected or inserted This may cause a problem when ejecting or inserting a disc To insert a disc insert the disc into the center of the drive with the appropriate pressure If you insert a disc and apply excessive force to one side of the tray it may result in a problem Using LightScribe Optional LightScribe is a feature that allows you to print letters or images onto the surface of a CD DVD when recording data LightScribe s features are provided for DVD Super Multi N drives ODDs that support LightScribe If the LightScribe logo z lt is on the surface of the CD drive ODDs it means the LightScribe feature is supported Click Start gt All programs gt CyberLink DVD Suite gt LabelPrint gt LabelPrint A The CyberLink Label Print screen appears INO Click on LightScribe to use the feature Please refer to the Help information for the application for more detailed instructions GO Even if the Disk label print program is installed on tv your computer or the LightScribe Control Panel program icon is in the system tray of the Taskbar you cannot use the LightScribe function if your CD ROM drive ODD does not support this function ifthe LightScribe menu is not shown in CyberLink Label Print even for a model that supports LightScribe please go to http www l
65. er Information Samsung Electronics Co Ltd 416 Maetan 3Dong Yeongtong Gu Suwon City Gyeonggi Do 443 742 Korea Samsung Electronics Suzhou Computer Co Ltd No 198 Fangzhou Road Suzhou Industrial Park Jiangsu Province 215021 China Tel 86 512 6253 8988 For the web or the phone number of Samsung Service Centre see the Warranty or contact the retailer where you purchased your product European Radio Approval Information for products fitted with EU approved radio devices This Product is a Notebook computer low power Radio LAN type devices radio frequency RF wireless communication devices operating in the 2 4GHz 5GHz band may be present embedded in your notebook system which is intended for home or office use This section is only applicable if these devices are present Refer to the system label to verify the presence of wireless devices Wireless devices that may be in your system are only qualified for use in the European Union or associated areas if a CE mark with a Notified Body Registration Number and the Alert Symbol is on the system label The power output of the wireless device or devices that may be embedded in you notebook is well below the RF exposure limits as set by the European Commission through the R amp T TE directive The low band 5 15 5 35 GHz is for indoor use only countries or regions within countries under the heading European Economic Area Restrictions below KH
66. era formatting the data using the digital device is recommended When you try to use a card which is formatted in the computer in another digital device you may have to format the card again in the device You cannot format write or delete data from a SD or SDHC card with a write protection tab when it is in the Lock position Inserting and removing a memory card repeatedly may damage the memory card ExpressCard Slot optional You can use Express cards using this slot The ExpressCard slot can be regarded as the next generation PCMCIA card specification and supports LAN TV Tuner and Sound cards This computer s slot supports the Express Card 34 specification Q Before You Start Remove the dummy card installed to protect the slot first Optional Lightly push the dummy card of the slot The dummy card pops up Eject the dummy card This slot is a ExpressCard slot You cannot connect a PCMCIA card here Since these descriptions are written on the basis of the latest operating system Windows 7 some of the content and the figures of the descriptions may differ depending on the operating system Since the procedures for other Windows operating systems are similar use the computer referring to these descriptions To insert a card 1 2 If a window asking whether you want to scan and NI change appears click on Continue Without Scan Insert a card into the slot on the side of the This will proceed to Step 2
67. ere is a danger of fire due Damage to the device within the to an incomplete contact computer may cause electric shock or fire hazard Use only the AC adapter supplied with the product Using another adapter may cause the screen to flicker a Keep the power cord or outlet clean so that they are not covered with dust Failing to do so may result in fire J A Warning Failing to follow instructions marked with this symbol may cause personal injury and even fatality Do not place heavy objects or step onto the power cord or AC adapter to avoid damaging the power cord or AC adapter If the cord is damaged there is a danger of electric shock or fire Battery Usage Related Keep the battery out of the reach of infants and pets as they could put the battery into their mouths There is a danger of electric shock or choking 10 Authorized Parts Use an authorized battery and AC adapter only Please use an authorized battery and adapter approved by Samsung Electronics Unauthorized batteries and adapters may not meet the proper safety requirements and may cause problems or malfunctions and result in an explosion or fire A Warning Failing to follow instructions marked with this symbol may cause personal injury and even fatality Do not use the computer in a badly ventilated location such as on bedding on a pillow or cushion etc and do not use it in a location such a
68. es The latch used to remove or install the battery 2 Memory Compartment The main memory is installed inside the cover Cover 3 Hard Disk Drive The hard disk drive is installed inside the cover Compartment Cover 4 MINI CARD Cover The WLan Card is installed inside the cover 5 Speaker A device used to generate sound 46 Turning the Computer On and Off Turning the computer on 1 Install the battery and connect the AC adapter Power button LED is lit while the computer is turned on Lift the LCD panel up LED 3 Press the Power button to turn the computer on If you press and release the Power button on the Q computer when it is on the computer enters Sleep mode When running the computer on battery power the LCD brightness is dimmed automatically to save battery power brightness When turning the computer on for the first time the Register Windows screen appears You can use the computer after registering your user information 4 Turning the computer off Q Since the procedures to turn the computer off may differ depending on the installed operating system please turn the computer off according to the procedures for the purchased operating system 1 Click the Start button on the taskbar gt For Windows Vista Click on Start gt E and then click on Shut Down as shown in the figure below to shut the gt For Windows 7 computer down Click Shut down to shut
69. es multichannel audio content to create a truly immersive surround sound experience with rich bass and clear dialog from the laptop speakers or headphones SsiS WOW HD is a trademark of SRS Labs Inc WOW HD technology is incorporated under license from SRS Labs Inc SRS WOW HD significantly improves the playback quality of mono and stereo audio delivering a dynamic 3D entertainment experience with deep bass and high frequency clarity for crisp detail Ti SIS is a trademark of SRS Labs Inc CS Headphone technology is incorporated under license from SRS Labs Inc CS Headphone delivers a 5 1 surround sound experience over standard headphones or earbuds when listening to multichannel content such as DVD movies All other product or company names mentioned herein are registered trademarks of their respective companies 127 I Glossary The Glossary lists the terminologies used in this User Guide For terminologies other than these look in Windows Help Backup A way to save the current data to restore it later if necessary A backup is a way to restore computer data when the data or computer is damaged Chargeable USB This program enables supplying power to a specific USB port when the system is in power saving mode hibernation mode or off Client This refers to a computer that uses a shared network resource provided by a server DDR SDRAM Double Data Rate Synchronous Dynamic Random Access
70. g Windows View pictures o song a USIng Windows View pictures using Windows Media Center General options ue e You can only use the card after formatting it Q The device name of the card drive may differ depending on your computer model i Speed up my system baz using Windows ReadyBoost Set AutoPlay defaults in Control Panel Using a Mini SD and RS MMC Since the above cards are too small you cannot insert the cards into the slot directly Insert the card into the dedicated adapter available If a window asking to scan and change appears click from most electronic retailers and then insert the Continue Without Scanning This will proceed to Step adapter into the multi card slot 2 above However depending on the adapter s body material some RS MMC cards may not be recognized properly Samsung recommend that you check the card is recognized correctly prior to purchasing To remove a memory card Take hold of the end of the card and remove the card To format a memory card When using the memory card for the first time you must format the card before using it If the card includes data backup the data before tv Formatting a card deletes all data saved on the card formatting it 1 Click Start gt Computer Right click over a card drive with the touchpad and select Format 3 Click Start to the formatting To use a card to exchange data with a digital device such as a digital cam
71. he electrical ground connections of the power utility telephone lines and internal metallic water pipe system if present are connected together This precaution may be particularly important in rural areas To avoid electrical shock or equipment malfunction do not attempt to make electrical ground connections by yourself Contact the appropriate inspection authority or an electrician as appropriate The Ringer Equivalence Number REN assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5 European Union European Union CE Marking and Compliance Notices Products intended for sale within the European Union are marked with the Conformit Europ ene CE Marking which indicates compliance with the applicable Directives and European standards and amendments identified below This equipment also carries the Class 2 identifier The following information is only applicable to systems labeled with the CE mark CE European Directives This Information Technology Equipment has been tested and found to comply with the following European directives EMC Directive 2004 108 EC Low Voltage Directive 2006 95 EC R amp TTE Directive 1999 5 EC Manufactur
72. he figure above You can add clients services and protocols When you have completed the settings click the OK button The network settings have been completed Using both DHCP and a fixed IP simultaneously Using the Alternate Configuration providing by Windows Vista you can set both automatic and fixed IP addresses and then you can select to use either of them to connect to the Internet gt For Windows 7 Click Start gt Control Panel gt Network and Internet gt Network and Sharing Center and click on Change adapter settings in the left menu pane gt For Windows Vista Click Start gt Control Panel gt Network and Internet gt Network and Sharing Center and click Manage Network Connections in the left pane Right click over the Local Area Connection and select Properties 3 Select Internet Protocol Version 4 TCP IPv4 from the Networking tab and select Properties Select the Alternate Configuration tab select User configured fill in the corresponding fields and click the OK button Internet Protocol Version 4 TCP IPv4 Properties Alternate Configuration If this computer is used on more than one network enter the alternate IP settings below E Automatic private IP address User configured IP address Subnet mask Default gateway Preferred DNS server Alternate DNS server Preferred WINS server Alternate WINS server Validate settings if changed upon exit
73. he mouse cursor over the battery icon in the system tray of the Taskbar to confirm the remaining battery charge 98 remaining EN a lala e 10 35 AM e oe 7 21 2009 To view on the battery Separate the battery and press the PUSH button inside the battery The remaining battery charge will be displayed Battery Warning Y If the battery residual amount is 3 5 the computer automatically shuts down after saving the data The battery residual amount may vary depending on the computer model Battery Usage Time Information A battery is an expendable supply so when using it over a long time the capacity battery life is shortened If the battery life is reduced to under half of its initial time we recommend purchasing a new battery When not using the battery for a long time store the battery after charging it to 30 40 of its capacity This extends the battery life time Extending the Battery Usage Time Decreasing the LCD Brightness Press the Fn keys on the keyboard to decrease the LCD brightness to extend the battery usage time Using the Battery Calibration Function When charging discharging the battery repeatedly for a short time only the battery usage time may be reduced by the difference between the actual battery charge and the remaining charge display In this case the actual battery charge and the remaining charge display will be the same by discharging the battery comp
74. he version of the current Samsung Recovery Solution in the Samsung Recovery Solution screen Example If the program name that appears in the Samsung Recovery Solution screen is Samsung Recovery Solution 4 it indicates that the version of the Recovery Solution is version 4 If the name is Samsung Recovery Solution Ill it indicates that the version of the Recovery Solution is version 3 Restore Function Not only can you use Samsung Recovery Solution when Windows is running but also when you are unable to boot up into Windows Let s learn how to use Samsung Recovery Solution Partition Setup amp Initial Status Backup 3 The Initial Status Backup screen appears N To continue the Initial Status Backup click Restart If you turn your computer on for the first time the Initial Now The computer will restart Status Backup function is performed after registering Windows This function saves an image of the Initial Status of the C drive to a secure location so that users A The Initial Status Backup is performed to backup the initial status of the C drive to a secure location This backup image is used for the Complete Restore function that restores your computer to the initial status can restore the computer to the Initial Status using the Complete Restore function An Initial Status Backup is only performed once immediately after the computer is purchased 1 If you turn the power on for the first time the Register Windows screen
75. hich charges exceed local or long distance transmission charges In order to program this information into your fax machine refer to your communications software user manual Unintentional Emitter per ICES 003 This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the radio interference regulations of Industry Canada Le present appareil num rique n met pas de bruits radioelectriques d passant les limitesapplicables aux appareils num riques de Classe B prescrites dans le r glement sur le brouillage radioelectrique edicte par Industrie Canada Intentional Emitter per RSS 210 If fitted with 2 4G band or 5G band Low power Radio LAN type devices radio frequency RF wireless communication devices operating in the 2 4GHz 5GHz Band may be present embedded in your notebook system This section is only applicable if these devices are present Refer to the system label to verify the presence of wireless devices Wireless devices that may be in your system are only qualified for use in Canada if an Industry Canada ID number is on the system label When using IEEE 802 11a wireless LAN this product is restricted to indoor use due to its operation in the 5 15 to 5 25 GHz frequency range Industry Canada requires this product to be used indoors for the frequency range of 5 15 GHz to 5 25 GHz to reduce the potential for harmful interference to co channel mo
76. hooting Using Samsung Recovery Solution Optional 96 Samsung Recovery Solution Functions 96 Restore Function 99 Backup Function 102 System Software Function 106 Reinstalling Windows 7 Vista For Windows 7 and Windows Vista For supported models only 108 Q amp A 112 Windows Related 112 Display Related 114 Sound Related 116 Wired Network LAN Related 117 Wireless Network WLAN Related 119 Game and Program Related 123 Bluetooth 124 l Using Samsung Recovery Solution optional Samsung Recovery Solution is a program that can backup your hard disk and restores it later when a problem occurs with your computer It also provides a System Software function that enables you to install or backup device drivers and system software programs needed for your system to function properly Q Before You Start Samsung Recovery Solution may not be provided or the version may differ depending on the model In addition some functions may not be provided or may differ depending on the version For more information on using Samsung Recovery Solution please refer to the online help of the program The screen images in this document may differ from actual product f your computer does not have an internal ODD you need an external ODD connected to your computer to use the Backup Function or Restore Function using DVDs The System Software function may not be provided depending on the program version Samsung Recovery Solution Functi
77. ightscribe com and download the latest version of LightScribe l Multi Card Slot optional Using the multi card slot you can read and write data to a SD card SDHC card MMC card You can use a card as a removable disk and conveniently exchange data with digital devices such as a digital camera digital camcorder MP3 etc Before You Start You have to additionally purchase a multi card with the necessary capacity depending on your requirements You can use a multi card just like any data storage device A copyright protection function is not supported Since you can lose a card when moving the computer keep the card separately Before use remove the dummy card that was inserted to protect the slot Supported Cards SD Card SDHC card MMC The figures used for the description are of a representative model Therefore the figures may differ from the real ones To Insert and Use a Memory Card 1 Insert a card into the slot according to the directions printed on the slot Example SD Card The card drive appears Click Open folder and 3 You can save move and delete data by double view files clicking the corresponding drive If the window does not appear click Start gt Computer Devices with Removable Storage 2 le aa DVD Drive E AutoPlay Removable Disk F Removable Disk F al Mixed content options gt Play taij using Windows Media Player soy Import pictures sij usin
78. ing the shortcut key Switching the Display Device using the Shortcut Key Press the Fn Easy Display Manager screen appears in which you can select a display device Whenever you press the K 2 Fn key the selected option is changed O LCD CRT DualView Example Selecting LCD CRT Dual View LCD Notebook Screen CRT External Monitor Screen HDMI TV Screen or Monitor when it is connected via the HDMI port LCD CRT Clone Notebook External Monitor Screen LCD CRT DualView Notebook External Monitor Screen in Dual View LCD HDMI Clone Notebook TV or Monitor Screen LCD HDMI DualView Notebook TV or Monitor Screen Dualview What is Dual View Dual View is a function that enables you to view a computer screen over two display devices It is convenient when you need a wide screen Due to restrictions of the operating system the DualView function is not supported for Windows 7 Starter The TV screen is only supported for models that support the TV output port HDMI Simultaneous output to all 3 LCD CRT HDMI is not supported External Monitor TV is not supported in the DOS Command Prompt window Setting up HDMI TV video Optional Resize the Desktop using the resize bars so that the ER four arrows at the corners of the Desktop are placed in the corners of the TV and then click OK If the Desktop screen displayed on the TV does not fit to the TV screen configure it as fo
79. ining Battery Charge 131 81 88 60 85 41 126 12 92 S Safety Precautions Security Lock Port Shortcut Keys Status Indicators T Touchpad V Volume Control W Wired Network Wireless Network 94 50 42 53 72 74 77 MI3xx_Q
80. is a danger of electric shock Use the product within the operating conditions specified in the Manufacturers User Guide Keep the plastic bags out of the reach of children There is a danger of suffocation Keep a distance of 15cm or more between the computer and the wall and do not place any objects between them This may increase the internal temperature of the computer and may Cause an injury Do not install the computer ona slant or a place prone to vibrations or avoid using the computer in that location for a long time This increases the risk that a malfunction or damage to the product will occur Avoid exposing any part of your body to the heat from the computer vent or AC adapter for a long time when the computer is on Exposing a part of your body close to the heat from the vent or AC adapter for long periods of time may cause a burn Avoid blocking the vent at the bottom or side of the computer when using it on a bed or cushion If the vent is blocked there is a danger of damaging the computer or overheating the inside of the computer NP Ver 2 2 A Warning Failing to follow instructions marked with this symbol may cause personal injury and even fatality Power Related The power plug and wall outlet figures may differ depending on the country specifications and the product model Do not touch the main plug or If the power cord or power outlet Plug the power cord firmly in
81. is not available on our web site please contact your distributor European Economic Area Restrictions Kp Due to the fact that the frequencies used by Pe 802 11b 802 11g wireless LAN devices may not yet be Local Restriction of 802 11b 802 11g Radio Usage harmonized in all countries 802 11b 802 11g products Note to integrator The following statements on are designed for use only in specific countries or local restrictions must be published in all end user regions and are not allowed to be operated in countries documentation provided with the system or product or regions other than those of designated use incorporating the wireless product As a user of these products you are responsible for ensuring that the products are used only in the countries or regions for which they were intended and for verifying that they are configured with the correct selection of frequency and channel for the country or region of use Any deviation from permissible settings and restrictions in the country or region of use could be an infringement of local law and may be punished as such The European variant is intended for use throughout the European Economic Area However authorization for use is further restricted in particular countries or regions within countries as follows 7 N 38 General European standards dictate maximum radiated transmit power of 100 mW effective isotropic radiated power EIRP and the frequency range 2400 2483 5
82. itch is in the proper position for your area 24 Care During Use Do not walk on the power cord or allow anything to rest on it Do not spill anything on the system The best way to avoid spills is to not eat or drink near your system Some products have a replaceable CMOS battery on the system board There is a danger of explosion if the CMOS battery is replaced incorrectly Replace the battery with the same or equivalent type recommended by the manufacturer Dispose of batteries according to the manufacturers instructions If the CMOS battery requires replacement insure that a qualified technician performs the task When the computer is turned off a small amount of electrical current still flows through the computer To avoid electrical shock always unplug all power cables remove the battery and modem cables from the wall outlets before cleaning the system Unplug the system from the wall outlet and refer servicing to qualified personnel if The power cord or plug is damaged Liquid has been spilled into the system The system does not operate properly when the operating instructions are followed The system was dropped or the casing is damaged The system performance changes 29 The Instruction On Safety Operation of NotePC When installing and operating devices please refer to safety requirements in the user guide Devices can be used only with the equipment specified in the
83. l appearance of your computer Since these descriptions are written on the basis of the latest operating system Windows 7 some of the content and the figures of the descriptions may differ depending on the operating system Since the procedures for other Windows operating systems are similar use the computer referring to these descriptions The path may differ depending on the operating system Using the Touchpad you can use the following additional Gesture functions Scroll function using two fingers Zoom functions using two fingers Rotation function using two fingers Move function using three fingers Slide Show function using three fingers Configuring the Gesture Function The Touchpad Settings window appears Click over the corresponding item to select the item in the Select an item and click OK If the Gesture function is not activated you can activate it according to the following procedures To cancel the Gesture function unselect the Click the Start gt Control Panel gt Hardware and corresponding item in the Touchpad Settings window Sound gt Mouse gt Device Settings tab gt Settings and click OK button The Scroll Function This function is the same as the scroll area of the Touchpad If you place two fingers over the Touchpad and move them up down left or right the screen is scrolled up down left or right or Zoom Functions If you place two fingers over the Touchpad together
84. ld not be disposed of with other household waste at the end of their working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take these items for environmentally safe recycling Business users should contact their supplier and check the terms and conditions of the purchase contract This product and its electronic accessories should not be mixed with other commercial wastes for disposal be Correct disposal of batteries in this product Pb Applicable in the European Union and other European countries with separate battery return systems This marking on the battery manual or packaging indicates that the batteries in this product should not be disposed of with other household waste at the end of their working life Where marked the chemical symbols Hg Cd or Pb indicate that the battery contains mercury cadmium or lead above the reference levels in EC Directive 2006 66 If batteries are not properly disposed of these substances can cause harm to human health or the environment To protect natural resources and to promote material re use please separate batteries from other types of waste and recycle
85. letely using the Battery Calibration function and then recharging it again 1 2 Disconnect the AC power adapter after turning off the computer Restart your computer and press the F2 button when the Samsung logo appears to start the BIOS Setup 3 Move to the Boot gt Smart Battery Calibration item using the direction keys and press lt Enter gt XXXXXXXX SecureCore tm Setup Utility Advanced Main Security NumLock Off ae Summary screen Disabled opu Boot time Diagnostic Screen Disabled PHE OPROM Only with F12 Brightness Mode Control Auto Wireless Device Control Always On Smart Battery Calibration Highlight Yes in the Battery Calibration Confirmation window and press lt Enter gt The Battery Calibration function is activated and the battery is forcefully discharged To stop the operation press the lt Esc gt button This operation requires 3 5 hours depending on the battery capacity and the remaining battery charge I Using the Security Lock Port You can connect a Kensington lock to the Security Lock port to prevent your computer from being stolen when you have to use the computer in a public place To use this feature you have to purchase the Kensington lock additionally To use the Kensington lock refer to the product manual Tie the Kensington lock cable to a fixed object and install the other end of the cable to the Security Lock port Chapter 4 Troubles
86. llows depending on the graphics card You can view the graphics card type by selecting N Device Manager gt Display adapters and then clicking the symbol The screen images and terms may differ from actual product depending on the computer model and driver version For NVIDIA graphics cards 1 Right click over the Desktop and select NVIDIA Control Panel Horizontal Resize Bar Vertical Resize Bar In the Select a Task window in the left panel select the Video and Television gt Resize HDTV Desktop item and then click Resize Desktop You Gan esce fhe Geakico peame of your HOTY to acheve the moat Geared weeny epetece I your denice a berg cropped by he edges of you HDTV you can decrease the sue of your desktop so fti beter 1 Select the HDTV you would Mike to change pargi 2 To resize the MOTY desktop CA the Resize Deio button You ni be cresentied wit a screen where you can revesse oF decrease De sue of desto System letormation For Intel graphics cards Right click over the Desktop and select Graphics Properties Click Display Settings and click the Aspect Ratio Options intel Graphics Media a Accelerator Driver g Digital for mobile Television Display Devices Color Quality Rotation V Enable Rotation Screen Resolution 1280 x 720 ial eo Color Correction 7 A A g9 l 2A C 270 Display Expansion Hot Keys C 180 ntel EE os o
87. lts in Control Panel This screen may not appear depending on the security level 3 If the Select Windows Installation window appears click Install Now When the Select Update window appears click on the relevant item Windows 7 Install now gt What to know before installing Windows Windows 7 installation selection window install Windows Windows Vista Check compatibility online gt Install now What to know before installing Windows Transfer files and settings from another computer Copynght 2007 Microsoft Corporation All nghts reserved Windows Vista installation selection window If you select Go online to get the latest updates Q for installation in the Select Update window the latest updates are installed and Step 4 follows At this time the computer must be connected to the Internet For Windows 7 Vista the screen asking for the operating system to be installed may appear depending on the version If you click the Next button the screen of Step 4 appears A If the User Agreement screen appears select accept the license terms and then click Next Q For Windows 7 Vista this screen may not appear depending on the version The following window appears select an installation option E 2 Install Windows Which type of installation do you want Upgrade Keep your files settings and programs and upgrade Windows Be sure to back up your files bef
88. m performance or low noise low power consumption with one click Silent Low noise and low power consumption mode Normal Normal Mode Speed Maximum performance mode The system operates in its maximum performance and system resources are allocated to the currently active program with priority for maximum performance If you don t want fan noise turning ON and OFF in the Silent mode select the Advanced Q menu gt Fan Silent Mode gt Low in the BIOS Setup The fan keeps turning ON and works in Low noise mode Turns the wireless LAN function on or off in models with wireless LAN capability Turns the Touchpad function on or off When using an external mouse only you can turn the Touchpad off Turns the numeric keyboard on or off If you turn the Scroll Lock on you can scroll the screen up or down without changing the cursor location in some applications Press the Fn ca key combination to eject a CD You can only use this function when the Easy Display Manager program is installed Screen Brightness Control To adjust the LCD brightness press the Fn key combination or the Fn key combination The changed screen brightness is displayed at the center of the screen for a moment Volume Control Numeric Key The numbers are printed in blue on the numeric keys lf Num Lock is turned on by pressing the Fn combination you can use the numeric keys to enter digits
89. mputer in an open environment with no walls or obstacles in the way and having low radio interference You can connect to only one Bluetooth device ata time for a phone connection data syncing electronic business card exchange FAX transmission reception sound related functions and serial port functions It is recommended using only one Bluetooth device at a time as connecting multiple Bluetooth or other wireless devices at the same time may slow or destabilize the Bluetooth connection Data communications via Bluetooth may be poor when the CPU load is at full capacity or there are insufficient system resources The Bluetooth function of a Bluetooth PDA mobile phone mouse or keyboard may be turned off To use them in connection with a Samsung computer supporting Bluetooth you must check if the Bluetooth function of the device to connect to is turned on For the procedures on turning on the Bluetooth function of a device refer to the relevant device manual The services provided by Bluetooth devices may vary depending on their capabilities For the services provided by the Bluetooth device refer to the device manual Chapter 5 Appendix LI Z Product Specifications 126 Glossary 128 Index 131 Product Specifications The system specifications may differ depending on the derived models For detailed system specifications refer to the product catalogue CPU Optional Intel Core2 Duo Pentium Dual Cor
90. mputer model For detailed specifications refer to the catalogue Do not insert a cracked or scratched CD Otherwise the CD may break and damage the optical disk drive when the CD rotates at a high speed When you clean a CD or DVD title wipe with a soft cloth from inside to outside Insert a Mini CD into the center of the CD drive The figures used for the description are of a representative model Therefore the figures may differ from the real ones Using a CD that is not in the shape of a circle is not recommended DVD Super Multi LS LightScribe are only available for some models Inserting and Ejecting a CD 1 Insert the disc into the CD Drive so that the top To eject a disc press the Fn of the disc faces upwards When 90 of the disc combination Alternatively click Start gt Computer is inserted into the drive the disc is automatically gt CD Drive right click over the CD Drive and then loaded into the drive select Eject from the popup menu Then the disc operation stops and the disc is ejected from the CD Drive The Fn key combination works in the BIOS Setup DOS and Windows However it will not work during or just after booting up or before the Easy display manager is launched in Windows f it does not work in Windows double click My CD Drive Computer right click over the CD Drive and select Eject from the popup menu to eject a CD ACD drive s reading and writing speed may diff
91. ngth is excellent but cannot cannot find an AP connect to the network A Verify whether the Wireless LAN LED is on Even if the signal strength is excellent the If it is turned off turn it on by pressing the Wireless NOOTE connection may NO POr AA propery a if the TCP IP properties are not properly LAN On Off button Fn configured or the network key encryption key is incorrect A Check that the TCP IP properties are configured The Wireless LAN device is operating properly l but I cannot connect to the Internet or to another properly When connecting to an AP right click the Network Connections icon on the taskbar and computer ind select Network and Sharing Center If you click the View Status next to a connected wireless network device and then click the Detail button you can view the IP information If the IP is not allocated properly A1 When connecting to a wireless Ad Hoc network the IP address will be displayed as follows e g check if the network name SSID is the same 169 254 xXXX XXX If the network does not provide DHCP you have to specify the correct IP address by asking your network administrator This is due to an incorrect configuration or a configuration error Check the following A2 If a network key encryption key is used the AP Access Point and wireless Ad Hoc network keys h must be the same Even if the network provides DHCP the server may not allocate an I
92. ning the computer on again 2 Select the Boot menu and set the Brightness Mode Control item to User Control 3 Press the F10 key to save the settings and exit Setup Saving battery power consumption Decreases the LCD brightness when the computer is running on battery power to save battery power consumption LCD bad pixels principle of laptop computer Samsung observes the specifications regarding strict quality and reliability of LCD But in spite of that it is inevitable that there might be a small number of bad pixels A large number of bad pixels can cause problems in appearance but a small number of pixels doesn t affect the computer performance Therefore Samsung observes and manages the following dot principles Bright dot 2 or less Black dot 4 or less Combination of Bright and Dark 4 or less EA Instructions for Cleaning the LCD Clean the LCD panel with a soft cloth lightly moistened with computer cleansing detergent moving in one direction Cleaning the LCD panel with excessive force can damage the LCD BIOS Setup The BIOS Setup enables you to configure your computer hardware according to your needs Before You Start Use the BIOS setup to define a boot password change the booting priority or add a new device Since incorrect settings may cause your system to malfunction or crash take care when configuring the BIOS The functions of the BIOS setup are subject to change for product function enh
93. nquire at your service center before connecting the device There is a danger of damaging the product 19 Custody and Movement Related When moving the product turn the power off and separate all connected cables first The product might be damaged or users may trip over the cables For long periods of not using the notebook computer discharge the battery and preserve as it is detached The battery will be preserved at its best condition Do not operate or watch the computer while driving a vehicle There is a danger of a traffic accident Please concentrate on driving AN Caution Failing to follow instructions marked with this symbol may cause slight injury or damage to the product Cautions on Preventing Data Loss Hard Disk Management Take care not to damage the data on a hard disk drive A hard disk drive is so sensitive to external impact that an external impact may cause loss of data on the surface of the disk Take extra care because moving the computer or an impact on the computer when it is turned on may damage the data of the hard disk drive The company is not liable for any loss of any data caused by a customer s careless usage or bad environmental conditions Causes that may damage the data of a hard disk drive and the hard disk drive itself The data may be lost when an external impact is applied to the disk while disassembling or assembling the computer The data may be lost
94. nter gt A When a message confirming the password configuration appears in the Setup Notice window press lt Enter gt The supervisor password has been set XXXXXXXX SecureCore tm Setup Utility Security Boot Exit Supervisor Password Clear User Password Clear Mel Advanced The supervisor password is required to turn the computer on or to enter the BIOS Setup Sup HDD Password Clear con sett a a Set HDD Password Enter Password on boot Disabled Fixed disk boot sector Normal Setting a User Password Users can start the system with a user password but cannot enter the System Setup By doing this you can prevent other users from entering Setup Before configuring a user password a supervisor password must have been configured Deactivating the supervisor password also deactivates the user password In the Set User Password item press lt Enter gt and complete the procedures from Step 3 of Setting a Supervisor Password Setting Up a Boot Password To setup a boot password the administrator password Set Supervisor Password should be set in advance Set the Password on boot item to Enabled Once a boot password is set you have to enter a password to boot up the computer Setting up a Hard Disk Drive Password Optional A supervisor password must be set using the Set Supervisor Password menu lf you set a password for a hard disk drive it cannot be accesse
95. nu A2 Verify whether the same network key encryption key has been entered for both the AP and the computer The network key is an encryption key for encrypting the data transmitted between the AP and the computer It is recommended setting the network key manually Check the AP Settings For the AP settings refer to the User Guide provided by the AP manufacturer A3 Verify whether the environment is suitable for using a wireless LAN The use of a wireless LAN may be restricted according to the environment and distance Obstacles such as walls or doors affect the use of a wireless LAN Install the AP in a high and open space 50cm from the wall and far removed from any other radio signal sources A4 Verify whether the AP is operating properly When the AP is not operating normally turn off the AP wait a short while and turn it on again Verify whether the AP s firmware is the most recent version Contact the AP manufacturer or the place where you purchased the AP for details of the AP firmware A5 Verify whether the AP has been properly connected to the network Verify whether the network is operating normally by connecting the wired network cable which has been connected to the AP to your computer A6 Check the network key settings encryption key again When automatic code conversion a passphrase function has been selected and data communication is not functioning even with a normal wireless connection
96. ock Caps Lock Scroll Lock HDD ODD Wireless LAN Charge Status Power This turns on when the Num Lock key is pressed and numeric keypad is activated This turns on when the Caps Lock key is pressed allowing capital letters to be typed without holding the Shift button down This turns on when the Scroll Lock key is pressed and screen scroll is locked This turns on when the hard disk is or ODD being accessed This turns on when the wireless LAN is operating This shows the power source and the battery charge status Green When the battery is fully charged or the battery is not installed Amber When the battery is being charged Off When the computer is running on battery power without being connected to AC adapter This shows the computer operating status On When the computer is operating Blinks When the computer is in Sleep mode D 42 Right View 1 1 CD Drive ODD Optional Plays CD or DVD titles Since an ODD Optical Disk Drive is optional the installed drive depends on the computer model 2 USB Port gt You can connect USB devices to the USB port such as a keyboard mouse digital camera etc 3 DC Jack seo A jack to connect the AC adapter that supplies power to the computer Left View 1 2 3 4 5 678 9 1 Security Lock Port 2s You can connect a Kensington lock to the Security Lock Port to prevent the computer from being stolen 2 Wired LAN Port Optional Connect the Ethernet cable
97. ock or cover these openings However to ensure safe use of this product it is important Make sure you provide adequate space at least 6 that the safety instructions marked on the product and in inches 15 cm around the system for ventilation when the documentation are followed you set up your work area Never insert objects of any kind into the computer ventilation openings Ensure that the fan vents on the bottom of the casing Ki Always follow these instructions to help guard against are clear at all times Do not place the computer on a personal injury and damage to your system soft surface doing so will block the bottom vents f you use an extension cord with this system make sure that the total power rating on the products Setting Up your System plugged into the extension cord does not exceed the extension cord power rating Read and follow all instructions marked on the product and in the documentation before you operate your system Retain all safety and operating instructions for future use Do not use this product near water or a heat source such as a radiator Set up the system on a stable work surface The product should be operated only with the type of power source indicated on the rating label Ensure that the electrical outlet you are using to power your equipment is easily accessible in case of fire or short circuit f your computer has a voltage selector switch make sure that the sw
98. of the OS or visit Microsoft s website 0 What are the restrictions of Windows 7 Starter A The DualView function is not supported when an external display device is connected The Aero function of Windows 7 is not supported The Set as Background function to change the wallpaper of the Desktop is not supported Functions that are not supported by the operating system may also not be supported by related programs such as Easy Display Manager the graphics driver and so on Q For more information refer to the Help section of the OS or visit Microsoft s website DIESE WAGE Ire 0 The LCD screen is too dark or too bright A gt O Turn the LCD backlight on or adjust the LCD brightness Press Fn __ to turn the LCD backlight on or press Fn be or Fn t to adjust the LCD brightness The screensaver is activated while Media Player is playing a movie or video clip Unselect Library gt More Options gt Player gt Allow screen saver during playback in the Media Player In the following cases the screen blinks or there is noise for a short time Click the Graphics Related tab Change Resolution Change Display Device Remove the AC Adapter Restart the System Change Power Scheme This may happen while the video driver is examining the connected device While the detection process is busy any connected display devices may blink or some noise may occur gt
99. of the FCC rules On the back of this equipment is a label that contains among other information the FCC registration number and ringer equivalence number REN for this equipment If requested this information must be provided to the telephone company This equipment uses the following USOC jacks RJ11C An FCC compliant telephone cord and modular plug is provided with this equipment This equipment is designed to be connected to the telephone network or promises wiring using a compatible modular jack which is Part 68 compliant See Installation Instructions for details The REN is used to determine the quantity of devices which may be connected to telephone line Excessive RENs on the telephone line may result in the devices not ringing in response to an incoming call In most but not all areas the sum of RENs should not exceed five 5 0 To be certain of the number of devices that may be connected to a line as determined by total RENs contact the local telephone company to determine the maximum REN for the calling area If the terminal equipment causes harm to the telephone network the Telephone Company will notify you in advance that temporary discontinuance of service may be required But if advance notice is not practical the telephone company will notify the customer as soon as possible Also you will be advised of your right to file a complaint with the FCC if you believe it is necessary 33 The telephone company m
100. omputer and contact a service terminals it may cause excessive center current flow and it may damage the There is a danger of an explosion or battery or result in a fire fire To use the computer safely replace a dead battery with a new authorized battery 12 A Warning Failing to follow instructions marked with this symbol may cause personal injury and even fatality Usage Related Disconnect all cables connected to the computer before cleaning it If you are cleaning a notebook computer remove the battery There is a danger of electric shock or damage to the product Do not connect a phone line connected to a digital phone to the modem There is a danger of a electric shock fire or damage to the product Do not place any container filled with water or chemicals over or near the computer If water or chemicals enter the computer this may cause fire or electric shock If the computer is broken or dropped disconnect the power cord and contact a service center fora safety check Using a broken computer may cause electric shock or fire hazard 13 Avoid direct sunlight when the computer is in an air tight location such as inside a vehicle There is a danger of a fire hazard The computer may overheat and also present opportunity to thieves Do not use your notebook PC for long periods of time while a part of your body is making direct contact with it The temperature of the
101. on for the backup in the Description field so that you can easily recognize it later and specify the Save Path If your computer has a DVD Writer you can specify the DVD drive as the Save Path A Samsung Recovery Solution on lS Samsung i Recovery Solution 4 Home gt Backup gt Data Backup This function backs up user data to another drive a DVD or an external storage device Enter a description for the backup select a location to save the backup file to and then dlick the Next button Backup Point 07 04 2009 Backup Capacity 5 27KB Description My data backup Save Path Local Disk 76 60GB Available D Local Disk 76 60GB Available E DVD Drive Select Drive D Select the DVD drive If you have specified a hard disk drive or a removable ae disk as the Save Path the SamsungRecovery SamsungData folder is created on the corresponding drive e g D and the data is saved to the folder Take care to not delete the folder by mistake or on purpose H If you click the Next button the Data Backup begins If you have selected the DVD drive as the Save Path the Insert a blank DVD message appears Insert a blank DVD and click the OK button 6 The Backup is completed message appears O Data Restore 1 When backing up onto DVD Turn the computer on and insert the backup DVD into the DVD drive When backing up to another drive Proceed to Step 2 Click Start g
102. onnect only permitted devices to the connectors or ports of the computer Failing to do so may cause electric shock and fire Close the LCD panel only after checking if the notebook computer is turned off The temperature may rise and it may cause overheating and deformation of the product 17 Do not press the Eject Button while the Floppy Disk CD ROM drive is in operation You might lose data and the disk might be suddenly ejected and could cause an injury Take care not to drop the product while using it This may cause personal injury or loss of data Do not touch the antenna with electricity facility such as the power outlet There is a danger of electric shock When handling computer parts follow the instructions on the manual supplied with the parts Failing to do so may cause damage to the product AN Caution Failing to follow instructions marked with this symbol may cause slight injury or damage to the product If the computer emits smoke or there is a burning smell disconnect the power plug from the wall outlet and contact a service center If your computer is a notebook computer make sure to remove the battery There is a danger of fire Do not use a damaged or modified CD Floppy Disk There is a danger of damaging the product or personal injury Do not insert your fingers into the PC Card Slot There is a danger of injury or electric shock Use recommended computer cl
103. ons Samsung Recovery Solution 4 Home i Restore A function that restores the computer to a Samsung Recovery Solution is a program that backs up the current status of the computer and restores the computer hard disk drive when a problem occurs previous state after a problem occurs Select by Smptom Backup A function that backs up the data on the computer E System Software A function that reinstalls or backs up device drivers and application programs needed Restore Backup System Software for the system To view a brief description of an icon move the cursor over the icon If you need help click on Select by Symptom Q The system software function is supported by Samsung Recovery Solution version 4 or later Therefore the function may not be supported depending on the version ap Please back up your important data as data loss may occur for the C drive while restoring backing up the computer through Samsung Recovery Solution O Restore Function Using this function you can easily restore your computer to a previous stable state when your computer no longer works properly or you are unable to boot up your computer due to some problem If you have backed up data you can restore the backup data Restore Functions D Basic Restore Complete Restore Data Restore This function quickly restores This function deletes the entire C drive and then This function restores the user major Windows file
104. or apart the current image or text is Zoomed in or out Rotation Function If you place two fingers over the Touchpad and keep one finger in place and turn the other finger in the left or right direction the mouse pointer changes into the icon and the current photo or image is rotated Move Function When watching a photo or surfing the Internet you can move to the previous or next photo or Internet page without using the mouse or buttons Place three fingers over the Touchpad and slightly touch the surface of the Touchpad with them in the left or right direction to move to the previous or next photo or Internet page For example if you touch the Touchpad in the left direction using three fingers while looking at a website the previous page is displayed Slide Show Function When viewing a photo if you place three fingers onto the Touchpad and slide them upwards the Slide Show begins To finish the Slide Show place three fingers onto the Touchpad and slide them downwards Touchpad On Off Function If you want to use the mouse only without using the touchpad you can turn the touchpad off To lock the touchpad function press the Fn in the tabs that appear when clicking Start gt Control You can set the touchpad and touchpad button settings Panel gt Hardware and Sound gt Mouse l CD Drive opp optional An optical disk drive is optional and may differ depending on your co
105. or touching any exposed parts of the body especially the face or eyes while transmitting Do not operate the radio or attempt to transmit data unless the antenna is connected if not the radio may be damaged Use in specific environments The use of wireless devices in hazardous locations is limited by the constraints posed by the safety directors of such environments The use of wireless devices on airplanes is governed by the Federal Aviation Administration FAA The use of wireless devices in hospitals is restricted to the limits set forth by each hospital Explosive Device Proximity Warning Do not operate a portable transmitter Such as a wireless network device near unshielded blasting caps or in an explosive environment unless the device has been modified to be qualified for such use Use On Aircraft Caution Regulations of the FCC and FAA prohibit airborne operation of radio frequency wireless devices because their signals could interfere with critical aircraft instruments 30 Other Wireless Devices Safety Notices for Other Devices in the Wireless Network Refer to the documentation supplied with wireless Ethernet adapters or other devices in the wireless network interference basis with other devices operating at this frequency Any changes or modification to said product not expressly approved by Intel could void the user s authority to operate this device e The Part 15 radio device operates on a non
106. ore upgrading Custom advanced Install a clean copy of Windows select where you want to install it or make changes to disks and partitions This option does not keep your files settings and programs Help me decide If you click Custom the procedures from Step 6 continue sequentially If you click Upgrade the procedures from Step 7 continue sequentially For Windows 7 Vista this screen may not appear depending on the version Custom Select this option to Reinstall Windows You have to reinstall all necessary device drivers and programs after the Custom installation In addition unnecessary folders and files may remain on the hard disk drives after the installation e g C Windows old etc Upgrade Select this option to Upgrade Windows while maintaining current files configurations and programs Although you therefore do not need to reinstall the device drivers and programs some programs may not work properly after the upgrade When a window appears asking for the location to install the operating system to select a disk drive partition and click the Next button us Drive D includes an area to save the backup image used by Samsung Recovery Solution Installing Windows to drive C is recommended When previous Windows installation files are in the selected partition a message appears informing you that the files and folders will be moved to the Windows old folder Click the OK but
107. ot configure the Image Sharpness in the NVIDIA Control Panel of NVIDIA Graphics The NVIDIA Control Panel gt Adjust desktop Color Settings gt Image Sharpening item is set to None and will not be configurable This is normal This function is only available for old graphic chipsets Sound Related Q A 0 2 How can I configure the sound for video or audio chatting Configuring the Realtek HD Audio Manager Select Control Panel gt Realtek HD Audio Manager Select the Mic tab Select the Noise Suppression and the Acoustic Echo Cancellation items and click the OK button When using the Acoustic Echo Cancellation option select the Play Device gt Speaker gt Level tab and set the Microphone to Mute cannot hear my voice with the internal microphone This is because the sound from the internal microphone is removed so that the sound is not delivered to the speaker and causes feedback from the internal microphone However you can record the sound from the microphone normally When using an external microphone select the Play Device gt Speaker gt Level tab and deselect Mute for the Microphone Then you can listen to the sound from the external microphone through the speakers Q Sound is recorded abnormally when I select the Acoustic Echo Cancellation option connect an external microphone select the Play Device gt Speaker gt Level tab and then deselect Mute for the Microphone This
108. ows operating systems are Since these descriptions are written on the basis of the latest operating system Windows 7 some of the content and the figures similar use the computer referring to these descriptions 1 Connect a LAN cable to the computer s LAN port Right click over the Local Area Connection and select Properties LE Network and Internet Network Connections gt File Edit View Tools Advanced Help By Organize Views Disable this network device m Diagnose this connec Name Status Device Name Connectivity Network Category LAN or High Speed Internet 1 A Local Area Connection aa _ Network cable unplugged K Intel R PRO 00r Disable Status Diagnose Click Start gt Control Panel gt Network and Bridge Connections Internet gt Network and Sharing Center Create Shortcut Delete Rename gt For Windows 7 Click the Change adapter settings in the left menu pane Q The LAN Device name may differ depending on your computer s Network Device Control Panel Home i s View your basic network information and set u Change adapter settings SAMSUNG PC Internet ange advanced sharing This computer settings Manage wireless networks b A x Q View your active networks You are currently not connecte Change your networking settings Gra Set up a new connection or network i Set up a wireless broadband dial up ad hoc or VP gt For Windows Vista
109. r pan European approval for connection to the analogue Public Switched Telephone Networks PSTNs of TE excluding TE supporting voice telephony services in which network addressing if provided is by means of Dual Tone Multi Frequency DTMF signaling Although this equipment can use either loop disconnect pulse or DTMF tone signaling only the performance of the DTMF signaling is subject to regulatory requirements for correct operation It is therefore strongly recommended that the equipment is set to use DTMF signaling for access to public or private emergency services DTMF signaling also provides faster call setup This equipment has been approved to Council Decision 98 482 EEC CTR 21 for Pan European single terminal connection to the Public Switched Telephone Network PSTN However due to differences between the individual PSTNs provided in different countries the approval does not of itself give an unconditional assurance of successful operation on every PSTN termination point In the event of problems you should contact manufacturer Technical Support WEEE SYMBOL INFORMATION Correct Disposal of This Product Waste Electrical amp Electronic Equipment Applicable in the European Union and other European countries with separate collection systems This marking on the product accessories or literature indicates that the product and its electronic accessories e g charger headset USB cable shou
110. rports Hospitals and Oxygen or flammable gas laden atmospheres are limited examples where use of wireless devices may be restricted or eliminated When in environments where you are uncertain of the sanction to use wireless devices ask the applicable authority for authorization prior to use or turning on the wireless device Every country has different restrictions on the use of wireless devices Since your system is equipped with a wireless device when traveling between countries with your system check with the local Radio Approval authorities prior to any move or trip for any restrictions on the use of a wireless device in the destination country If your system came equipped with an internal embedded wireless device do not operate the wireless device unless all covers and shields are in place and the system is fully assembled Wireless devices are not user serviceable Do not modify them in any way Modification to a wireless device will void the authorization to use it Please contact manufacturer for service Only use drivers approved for the country in which the device will be used See the manufacturer System Restoration Kit or contact manufacturer Technical Support for additional information 29 United States of America USA and Canada Safety Requirements and Notices Do not touch or move antenna while the unit is transmitting or receiving Do not hold any component containing the radio such that the antenna is very close
111. rvice provider General Requirements The requirements listed below are applicable to all countries All power cord sets must be approved by an acceptable accredited agency responsible for evaluation in the country where the power cord set will be used The power cord set must have a minimum current capacity of 7 A and a nominal voltage rating of 125 or 250 volts AC as required by each country s power system USA ONLY The appliance coupler must meet the mechanical configuration of an EN 60 320 IEC 320 Standard Sheet C7 or C5 connector for mating with appliance inlet on the computer 2 Regulatory Compliance Statements Wireless Guidance If fitted with 2 4G band or 5G band Low power Radio LAN type devices radio frequency RF wireless communication devices operating in the 2 4GHz 5GHz Band may be present embedded in your notebook system The following section is a general overview of considerations while operating a wireless device Additional limitations cautions and concerns for specific countries are listed in the specific country sections or country group sections The wireless devices in your system are only qualified for use in the countries identified by the Radio Approval Marks on the system rating label If the country you will be using the wireless device in is not listed please contact your local Radio Approval agency for requirements Wireless devices are closely regulated and us
112. s C restores the contents of the C drive completely data if the user previously Windows without touching the backed up data user configuration and data on T the C drive Initial Status Restore This function restores the computer to the initial status saved when the computer was run for the first time after it was purchased Complete Backup Restore This function restores the computer to the point where the user performed a Complete Backup O Backup Function You can backup the entire C drive or all your data to another hard disk drive or DVD You can restore the backed up drive or data using the Restore function Backup Functions p Initial Status Backup Complete Backup Data Backup This function backs up the initial This function backs up the entire This function backs up specific status of the computer drive C folders or files System Software function You can back up the System Software saved on the hard disk to another hard disk drive or DVD and reinstall part or all software programs to your computer System Software function J System Software Installation System Software Backup This function installs the system software programs needed for your computer This function backs up all System Software Programs The system software function is supported by Samsung Recovery Solution version 4 or later Therefore the function may N not be supported depending on the version You can confirm t
113. s room with floor heating as it may cause the computer to overheat Take care that the computer vents on the side or the bottom are not blocked especially in these environments If the vents are blocked the computer may overheat and it may cause a computer problem or even an explosion Do not use the computer in a humid location such as a bathroom or sauna Please use the computer within the recommended temperature and humidity range 10 35 C 20 80 RH 11 Baris nwOff E Do not close the LCD panel and put the computer into your bag to move it when it is still turned on If you put the computer into your bag without turning it off the computer may overheat and there is a danger of fire Shut the computer down properly before moving it Never heat the battery or put the battery into a fire Do not put or use the battery in a hot location such as a sauna inside a vehicle exposed to the heat and so on There is a danger of an explosion or fire A Warning Failing to follow instructions marked with this symbol may cause personal injury and even fatality Q Please charge the battery fully before using the computer for the first time Take care not to allow metal objects If liquid leaks out of the battery or such as a key or clip to touch the there is a funny smell coming from battery terminal metal parts the battery remove the battery from If a metal object touches the battery the c
114. ss the Fn 3 key combination or Fn Ea combination to adjust the volume Applications Press the Fn on or off j Ey Spea kers System Sounds Adjusting the Volume using the Volume Adjustment Program Click the Volume icon HD on the taskbar and slide the volume control bar to adjust the volume Using the Sound Recorder The procedures to record sound using the Windows Recorder are described below Mute 1 Connect a microphone to the microphone jack You can also use the internal MIC Right click over the Volume icon dh on the taskbar and select Recording Device 3 Check if the microphone is set as the default recording device If this is the case it is already set as the default device If not right click over the microphone and select Set default A Click Start gt All Programs gt Accessories gt Sound Recorder and click Start recording to start a recording A Sound Recorder Using SRS The SRS function enables you to experience more stereophonic sound using stereo speakers Every software program may not be provided Q depending on your computer model In addition some pictures may differ from actual product depending on the computer model and software version 1 Right click over the Volume icon id in the Taskbar and select Play Device P Select Speaker in the Play tab and click Properties window Select a mode and click the
115. t All Programs gt Samsung gt Samsung Recovery Solution gt Samsung Recovery Solution on and press the F4 key in the boot screen to enter restoration mode Q When you cannot start Windows turn the computer When the initial menu screen appears click Restore and then click Data Restore Select a backup item to be restored in the backup list and click the Next button La Samsung Recovery Solution Samsung i Recovery Solution 4 Home gt Restore gt Data Restore This function restores backed up files and folders Select the item you want and click the Next button Select Backup Date Description Capacity Source 07 04 2009 My data backup 5 27KB HDD The data to be restored My Documents My Pictures Favorites My Video Desktop My Music H C Drive File 26 Size 5 27KB Select a folder for the restoration and click the Next button Data Restore begins When Data Restore is completed check if the data has been restored to the specified folder System Software Function Using System Software When the initial menu screen appears click System Software gt System Software Installation The System Software function is a function that enables you to reinstall device drivers and System Software LS Samsung Recovery Solution Programs or back up those programs Samsung Recovery Solution 4 Home gt System Software The system software function is supported by system Softw
116. ta loss Please take care to avoid losing any important data and backup your data to prevent any such data loss Precautions for Operating System Support If a problem occurs because of the reinstallation of other operating systems OS or a previous version of a OS pre installed on this computer or a software that does not support the OS the company will not provide technical support a replacement or refund and if our service engineer visits you due to this problem a service charge will be applied About the Product Capacity Representation Standard About HDD Capacity Representation The capacity of the storage device HDD SSD of the manufacturer is calculated assuming that 1KB 1 000 Bytes However the operating system Windows calculates the storage device capacity assuming that 1KB 1 024 Bytes and therefore the capacity representation of the HDD in Windows is smaller than the actual capacity due to the difference in capacity calculation E g For a 80GB HDD Windows represents the capacity as 74 5GB 80x1 000x1 000x1 000 byte 1 024x1 024x1 024 byte 74 505GB In addition the capacity representation in Windows may be even smaller because some programs such as Recovery Solution may reside in a hidden area of the HDD About Memory Capacity Representation The memory capacity reported in Windows is less than the actual capacity of memory This is because BIOS or a video adapter uses a portion of memory or claims it for further use
117. tem memory If there is insufficient system memory the data is saved to the hard disk drive and loaded to memory when required This operation may temporarily stop displaying the picture on the screen In this case lower the game resolution or the screen settings Bluetooth 0 How to view the Bluetooth help information A Press the Windows F1 key combination to launch Windows Help and search for Bluetooth related items in the Help section When no headset is found or cannot be connected A1 Ifthe headset is already connected to another device you will not be able to find the headset and cannot connect to the headset even if the headset is found Disconnect the connection to the other device and then start the search again A2 If the headset is connected to a power adapter you cannot make a Bluetooth connection Disconnect the power adapter and then retry A3 In general a Bluetooth headset has 2 operating modes On Off mode and Pairing mode To connect the headset to another Bluetooth device such as a PC or cell phone the headset must be in Pairing mode Switch the headset to Pairing mode and then retry the search operation In general the headset in Pairing mode automatically returns to On Off mode after a certain period of time Usage Instructions Generally Bluetooth devices deliever stable performance while connected within a 3m 10 ft distance For Bluetooth to operate smoothly use the co
118. the monitor number 2 icon and select Extend these displays in the Multiple displays item Click the Apply button and then the OK button E Dapley Screen Relubon This is my main monitor Change the appearance of your displays tl i l i Resolution Low Highest 32 bit a e 1024 by 768 pixels Pesaha TEE How do I get the best display Advanced Settings Orientation Pulte displ Erered these displays A You must select Apply before making additional changes Eonnect to a projector tor prem the iF key and tap PA Mike tert and ether berg large or ematler What diepla ceeing eu chacca 3 When notebook LCD is set as the main device the 1 digit is displayed over it and the 2 digit is displayed over the auxiliary display device Now you can expand the Desktop screen over 2 display devices When using Dual View it is recommended setting the LCD as the main device number 1 Adjusting the resolution of the auxiliary display Q device Monitor Number 2 If the resolution of the auxiliary display device is output you can adjust the resolution and color quality by clicking Start gt Control Panel gt Appearance and Personalization gt Adjust screen resolution gt Monitor Number 2 p mw Gog Display Screen Resolution v 4 Seard Change the appearance of your displays a Display 2 Generic Non PnP Monitor x
119. to the power cord with wet hands makes a noise disconnect the power outlet and AC adapter There is a danger of electric shock power cord from the wall outlet and Failing to do so may cause fire hazard contact a service center There is a danger of electric shock or fire hazard Do not exceed the standard Do not use a damaged or loose Do not unplug the power cord out capacity voltage current of a main plug or power cord or power by pulling the cable only multiplug or power outlet extension outlet If the cord is damaged it may cause when using it for the product There is a danger of electric shock or electric shock There is a danger of electric shock or fire hazard fire hazard aN A Warning Failing to follow instructions marked with this symbol may cause personal injury and even fatality Do not bend the power cord excessively or do not place a heavy object over the power cord It is especially important to keep the power cord out of reach of infants and pets If the cord is damaged it may cause electric shock or fire Connect the power cord to an outlet or multiple power plug extended cable with a ground terminal Failing to do so may result in electric shock AC Adapter Usage Precautions If water or another substance enters the power input jack AC adapter or Connect the power cord to the AC the computer disconnect the power adapter firmly SAEI SNe COMETS WD SERAS SENN Otherwise th
120. ton J The Windows installation continues The computer will restart 3 times during the installation If the Press any key to boot from CD or DVD message appears after a restart do not press any button 8 Register a user according to the instructions on the Windows screen When the registration is complete the Windows Desktop screen appears Q For a smooth computer operation installing the necessary software installation is recommended Reinstalling when Windows does not H If the User Agreement screen appears select accept the license terms and then click Next start When Windows does not start boot up with the SYSTEM For Windows 7 Vista th RECOVERY MEDIA and from there you can reinstall PE e o een may not appear Windows 1 Insert the SYSTEM RECOVERY MEDIA into the DVD drive and restart the computer When the window asking for the installation type appears click Custom If the Press any key to boot from CD or DVD For Windows 7 Vista this screen may not appear message appears while booting press any key on depending on the version the keyboard Press any key to boot from CDorDVD When a window appears asking for the location to install the operating system to select the partition of the disk drive and then click the Next button RH Drive D includes an area to save the backup image used by Samsung Recovery Solution Installing 3 After a while the Options windows such as Win
121. ts Control Settings Select a level and click the OK button to finish the setting Q The Windows Firewall setting according to the network location for the Windows 7 operating system only Windows 7 allows different Windows firewall settings for each network location The following network locations are available Home Network Company Network and Common Network You can determine whether to use the Windows Firewall and select a firewall security setting for each location ifthe network setting window appears in Windows 7 after setting up the IP address select a location Click Start E gt Control Panel gt System and gt Security gt Windows Firewall gt Activate or Deactivate Windows Firewall Set up a firewall for the Home and Company Private Network Location Settings and the Common Network Location Settings and click the OK button What Is Virtual XP For Windows 7 only Virtual XP refers to a virtual operating system that allows you to run Windows XP virtually in the Windows 7 environment By using Virtual XP you can use applications that do not run on Windows 7 gt Requirements for Running Virtual XP Virtual XP is only available on these three operating systems Windows 7 Professional Ultimate and Enterprise The memory must be 2 GB or more and the virtualization function of the BIOS must exist and be activated by the CPU Q For more information refer to the Help section
122. twork Optional Connecting to a Wireless LAN 50 53 33 55 57 58 58 60 63 64 64 66 70 72 14 TT 77 l Keyboard Shortcut key functions and procedures are discussed in the following sections The keyboard is supplied according to the corresponding country The keyboard may differ depending on your country The following mainly describes the shortcut keys Shortcut Keys You can use the following functions by pressing the keys below with the Fn key Fn Name REST Sleep Mode Gauge Euro CRT LCD Backlight Mute Samsung Support Center Function Switches to Sleep mode To wake the computer up press the Power button Shows the remaining battery charge You can only use this function when the Easy Display Manager program is installed Enters the Euro monetary unit symbol This key may not be provided depending on the keyboard type Switches the screen output to the LCD or external monitor when an external monitor or TV is connected to the computer Turns the LCD backlight on or off Mutes or cancels mute System diagnosis recovery and Internet consultation program Samsung Support Center will be launched Optional For some models Samsung Magic Doctor is launched Fn Name Easy SpeedUp Manager Wireless LAN Touchpad Num Lock Scroll Lock To Eject a CD Function You can select operation mode when you need maximum syste
123. urning the Computer On and Off 47 Chapter 4 Troubleshooting Turning the computer on l Using Samsung Recovery Solution 96 Turning the Computer Ol an cine pose Solution Functions 96 Restore Function 99 Backup Function 102 i System Software Function 106 Chapter 2 Using the Computer Reinstalling Windows 7 Vista 108 Keyboard 50 Q amp A 112 Touchpad 53 Windows Related 112 Basic Touchpad Functions 53 Display Related 114 The Gesture Function of the Touchpad Optional 55 Sound Related 116 Touchpad On Off Function 57 Wired Network LAN Related nr CD Drive ODD Optional 58 ae eis Si sa lia ie Inserting and Ejecting a CD 58 icici OARE 1 A Multi Card Slot Optional 60 ExpressCard Slot Optional 63 Connecting a monitor TV 64 Connecting to the Monitor TV 64 Chapter 5 Appendix Viewing Through a Monitor TV 66 Using Dual View 70 Product Specifications 126 Adjusting the Volume 72 Glossary 128 Wired Network 74 Index 131 Wireless Network Optional 77 Connecting to a Wireless LAN 77 Safety Precautions For your security and to prevent damage please read the following safety instructions carefully Since this is commonly applied to Samsung Computers some pictures may differ from actual products A Warning Failing to follow instructions marked with this symbol may cause personal injury and even fatality Installation Related Do not install the product in places exposed to humidity such as a bathrooms There
124. vely press the left touchpad button twice quickly Drag Function Dragging refers to moving an item to another place after selecting it Press and hold down the left touchpad button over an item you want to drag and move the item to the new location Holding down the left touchpad button Right Button Function This corresponds to clicking the right mouse button Press the right touchpad button once The corresponding pop up menu appears Touchpad Scroll Function The touchpad scroll area provides the mouse wheel function scroll function Place your finger on the touchpad s right edge for vertical scrolling or the bottom edge for horizontal scrolling and then move your finger along the edge to scroll the screen vertically or horizontally The Gesture Function of the Touchpad Optional The Touchpad Gesture function may not be provided and the version of the function may differ depending on the model Some usage procedures may differ depending on the version For detailed usage procedures refer to the description in the Touchpad Settings window In addition if you click the Show Video button of each item you can refer to the video descriptions The images in this document may differ from the actual screen images and a different Touchpad may be provided depending on the model In addition since the pictures used in this document are pictures of a representative model they may differ from the actua
125. wareMediaXX 3 Specify the Save Path If your computer has a DVD f you want to install the System Software Programs Writer you can specify the DVD drive as the Save Path Gi A Samsung Recovery Solution Samsung i Recovery Solution 4 Home gt System Software gt System Software Backup This function enables backing up of the system software to another storage device If a device or Samsung application does not work properly it can be reinstalled using the backup DVD of the system software Select a location to save the backup data and click the Next button Backup Point 07 04 2009 Backup Capacity 666 MB Description Samsung System Software Save Path NTFS 76 0GB Available D NTFS 76 0GB Available E DVD Drive Caution Make sure to connect the power while the backup is pelformed If the Hower is turned off during a backup you have to restart tHe backup from the Select Drive D Select the DVD drive If you have specified a hard disk drive or a removable fal disk as the Save Path the SamsungSoftware folder is created on the corresponding drive e g D and the system software programs are saved to that folder Take care to not delete the folder exe file in the SystemSoftware folder When installing System Software Programs from the backed up DVD insert the DVD and follow the System Software Installation directions To delete Samsung Recovery Solution refer to the Help section
126. when the computer is turned off or reset by a power failure while the hard disk drive is operating The data may be lost and irrecoverable due to a computer virus infection The data may be lost if the power is turned off while running a program Moving or causing an impact to the computer while the hard disk drive is operating may cause files to be corrupted or bad sectors on the hard disk To prevent data loss due to damage to the hard disk drive please backup your data frequently 20 Proper Posture During Computer Use Maintaining a proper posture during computer use is very important to prevent physical harm The following instructions are about maintaining a proper posture during computer use developed through human engineering Please read and follow them carefully when using the computer Otherwise the probability of RSI Repetitive Strain Injury from repeated operations may increase and serious physical harm may be caused The instructions in this manual have been prepared so that they can be applied within the coverage of general users f the user is not included in the coverage the recommendation is to be applied according to the user s needs Proper Posture To use the computer while talking over the telephone 1 use a headset Using the computer with the phone on Adjust the heights of desks and chairs appropriate to your shoulder is bad for posture your height Keep frequently used items within a comfortabl
127. y as specified in the Product Specification Adding a Memory Module Insert a new memory module into the memory slot at an angle of approximately 30 degrees aligning it to the angle of the memory slot Remove the screw on the memory compartment cover at the bottom of the computer using a screw driver tilts DEPSUUUEUEVA RV RV LEAN LENG Fixing Screw Memory Slot 3 Push the memory module down so that it is completely fixed If the memory does not fit easily push the memory module down while pulling the memory module latches outward Close the memory compartment cover and fasten the screw Removing a memory module Pull the memory module latches outward The memory module will pop up Remove the memory module out at an angle of 30 degrees Battery Please refer to the following instructions when running the computer on battery power without connecting the AC power A Lithium lon smart battery is supplied with this computer Q Before You Start Carefully read and follow the precautions printed on the battery before using the battery Before using your computer for the first time after purchasing it charge the battery completely Precautions KA Use only chargers specified in the User Manual Never heat the battery pack put it near or in a fire or use at a temperature higher than 60 C as this may cause fire Never cause a short circuit between the battery pack terminals or disassembl
128. y when there is a device operating on an adjacent frequency in the vicinity of the product Channel interference may occur when a wireless video transceiver or a microwave oven is being used If you experience channel interference from other equipment we recommended changing the channel for connecting to the AP For more information about AP settings refer to the User Manual supplied by the AP manufacturer A2 Since IEEE802 11g equipment operates in hybrid mode when there is active IEEE802 11b equipment the data rate may be degraded Game and Program Related Windows may not provide some functions properly when performing some applications especially games or may cause a problem due to a device driver compatibility issue For the latest device drivers and bug fixes please refer to the respective company s website A 3D game does not work or some functions are The picture on the screen is displayed as a not working broken image for some games A Change the graphics settings of the game to 2D or A Apart of the picture on the screen may be broken Software Renderer then run the program again when playing some games that require a high specification graphics card In this case set the 3D function setting for the game The game is not displayed smoothly on the to a lower value or set the game resolution to a lower 0 screen value gt For 3D games the texture data for the 3D screen display is saved to the sys

Samsung NP-Q320E User Manual (Vista/Windows7)

Contents

Download Pdf Manuals

Related Search

Related Contents