Home

Samsung Series 7 63inch (PS63P71FDX) User Manual

1. This feature brings you more detailed image with 3D noise reduction detail enhancement contrast enhancement and white enhancement New image compensation Algorithm gives brighter clearer more detailed image to you DNle technology will fit every signal into your eyes gt This function is not available in PC mode gt When you select Movie in picture mode the DNIe cannot be selected Freezing the Current Picture You can freeze the picture when watching a television programme simply by pressing the STILL button To return to normal viewing press it again gt This function will automatically cancel five minutes later English 30 GUID STILL SUI at OST ORE Viewing Picture in Picture This product has one built in tuner which does not allow PIP to function in the same mode For example you cannot watch one TV channel in the main screen and a different one in the PIP screen Please see PIP Settings below for details You can use the PIP feature to simultaneously watch two video sources gt While Parental Lock is in operation the PIP function cannot be used Refer to page 41 Activating Picture in Picture 14 Press the MENU button to display the menu 2 Press the A or Y button to select PIP then press the ENTER OK button 3 Press the ENTER OK button again Press the A or Y button to select On then press the ENTER OK button gt If you turn the TV off while watching
2. Installing Batteries in the Remote Control 1 Lift the cover at the back of the remote control upward as shown in the figure 2 Install two AAA size batteries gt Make sure to match the and ends of the batteries with the diagram inside the compartment Do not mix battery types i e alkaline and manganese 3 Close the cover as shown in the figure gt gt Remove the batteries and store them in a cool and dry place if you won t be using the remote control for a long H time The remote control can be used up to about 23 feet tee from the TV Assuming typical TV usage the batteries last for about one year gt Ifthe remote contro doesn t work Check the following 1 Is the TV power on 2 Are the plus and minus ends of the batteries reversed 3 Are the batteries drained 4 Is there a power cut or is the power cord unplugged 5 Is there a special fluorescent light or a neon sign nearby Switching Your Television On and Off The main lead is attached to the rear of the television 14 Plug the main lead into an appropriate socket gt The main voltage is indicated on the rear of the television and the frequency is 50 or 60Hz 2 Press the C Power button On Off on the front of the television or press the POWER button on the remote control to switch the television on The programme that you were watching last is reselected automatically If you have not yet stored any channels no clear pi
3. gt This device is a Class B digital apparatus Design and specifications are subject to change without prior notice For the power supply and Power Consumption refer to the label attached to the product English 78 This page is intentionally left blank Contact SAMSUNG WORLDWIDE If you have any questions or comments relating to Samsung products please contact the SAMSUNG customer care centre Country Customer Care Centre Web Site AUSTRALIA 1300 362 603 www samsung com au CHINA 800 810 5858 010 6475 188038 www samsung com cn HONG KONG 2862 6001 www samsung com hk INDIA 3030 8282 1600 1100 11 www samsung com in INDONESIA 0800 112 8888 www samsung com id JAPAN 0120 327 527 www samsung com jp MALAYSIA 1800 88 9999 www samsung com my PHILIPPINES 1800 10 SAMSUNG 7267864 www samsung com ph SINGAPORE 1800 SAMSUNG 7267864 www samsung com sg SOUTH AFRICA 0860 7267864 SAMSUNG www samsung com za TAIWAN 0800 329 999 www samsung com tw THAILAND 1800 29 3232 02 689 3232 www samsung com th U A E 800SAMSUNG 7267864 www samsung com mea VIETNAM 1 800 588 889 www samsung com vn BN68 01314A 02
4. Enter new PIN Confirm new PIN 029 Enter PIN D Return Change PIN PIN is changed successfully OE9 Enter PIN D Return Continued English 41 How to Set up Restrictions Using Parental Rating First set up a personal identification number PIN and enable the V Chip See previous section 1 Press the MENU button to display the menu 2 Press the A or Y button to select Setup then press the ENTER OK button 3 Press the A or V button to select Parental Lock then press the ENTER OK button 4 Press the number buttons to enter your current 4 digit PIN gt The default PIN for a new TV set is 0 0 0 0 5 The Parental Lock screen will appear Press the ENTER OK button to select Parental Rating The Austraila screen for age rating G PG M MA AV R will appear 6 Press the A or V button to select an appropriate restriction 7 Press the ENTER OK button to activate the restriction selected The 4 symbol is indicated gt Allow All Press to unlock all TV ratings Block All Press to lock all TV ratings 8 Press the EXIT button to exit gt While viewing a DTV channel the Parental Lock function can be selected English 42 Subtitle Beene Menu Transparency Medium Energy Saving Off PC Normal Film Mode Off Wall Mount Adjustment Parental Lock Enter PIN eas eee ad OE9 EnterPIN SD Return Parental Lock Parental Rating Change PIN Move E
5. Image Lock Coarse Fine The purpose of picture quality adjustment is to remove or reduce picture noise Hon tre PC Position If the noise is not removed by Fine tuning alone then f E Auto Adjustment adjust the frequency as best as possible coarse and Fim Image Reset Fine tune again After the noise has been reduced readjust the picture so that it is aligned on the centre of screen 1 Press the A or Y button to select Coarse or Fine then press the ENTER OK button 2 Press the lt or gt button to adjust the screen quality vertical stripes may appear or the picture may be blurry Press the ENTER OK button Coarse Position Fine Adjust the PC s screen positioning if it does not fit the TV screen 1 Adjust the position by pressing the A lt gt button 2 Press the ENTER OK button Auto Adjustment Position Auto adjustment allows the PC screen of set to self adjust to the incoming PC video signal The values of fine coarse and position are adjusted automatically Image Reset You can replace all image settings with the factory default values Move 4 gt Adjust G Enter D Return lt gt Adjust Enter D Return A Auto Adjustment in Progress Please Wait A Image Reset is completed English 49 Changing the Picture Size PC Mode You can select the picture size which best corresponds to your viewing requirements gt You can change the picture size simply by pressing the P SIZE
6. Press the MENU button to display the menu Press the ENTER OK button to select Picture Press the A or Y button to select Size then press the ENTERIOK button Press the A or Y button to select the screen format you want then press the ENTER OK button Press the EXIT button to exit 16 9 Sets the picture to 16 9 wide mode 4 3 Set the picture in 4 3 format button on the remote control Picture Reset Move G Enter D Return TO CUO DU TNT np a i B O O O TEXT MIX PSIZE P MODE PIP GUIDE C_ LL SUBTITLE aL Setting the Home theatre PC You can view higher quality pictures by configuring the screen settings in PC Mode If you set the Home Theatre PC function to On you can configure the Detailed Settings when Picture Mode is set to Standard or Movie as in PC Mode 1 2 3 4 5 gt This function is available only in PC mode Press the MENU button to display the menu Press the A or button to select Setup then press the ENTER OK button Press the A or Y button to select Home theatre PC then press the ENTER OK button Select Off or On by pressing the A or Y button then press the ENTER OK button Press the EXIT button to exit lt 1 English 50 re Energy Saving PC Off Wall Mount Adjustment Light Effect Blue Screen Melody Screen Burn Protection Always On Medium Using the WISELINK Function This
7. English 18 Adding and Erasing Channels You can add or delete a channel to display the channels you want 14 Press the MENU button to display the menu 2 Press the A or V button to select Channel then press the ENTER OK button AA 3 Press the A or V button to select Channel List then ees press the ENTER OK button Auto Store 4 Press the lt button to select Added Channels Manual Store 5 Press the A or Y button to select All Channels then ARE press the ENTER OK button ga emean Shows all currently available channels _ ae 6 Press the A or button to select a channel to add then press the blue button 7 Press the ENTER OK button to select Add gt All added channels will be shown on Added Channels menu s 8 Press the A or Y button to select a channel to delete 7Digital2 then press the blue button Y 7Digital3 Press the ENTER OK button to select Delete j n 9 Press the EXIT button to exit c3 gt You can also delete a channel in the Added Channels a menu in the same manner Option Y7Digtal1 Delete from Favourite Timer Viewing annel Name Edit 7Digital 2 7Digital 3 Zoom Select Option gt You can select these options simply by pressing the CH LIST P SF Ne a E button on the remote control i WISELINK CHLIST FAV CH REC Continued English 19 Setting Your Favourite Channels You can set channels you watch frequently as favourites 1 Press the MENU button to display t
8. Managing Channels 18 Fine Tuning Channel Reception 24 LNA Low Noise Amplifier m29 Picture Control Changing the Picture Standard 26 Customizing the Picture Settings 27 Configuring Detailed Settings on the Picture 28 Selecting the Picture Size eee 29 Digital NR Active Colour DNIe 30 Freezing the Current Picture 30 Viewing Picture in Picture cece 31 Sound Control Sound Features oo ccc 33 Selecting the Sound Mode depending on the model ee 34 Symbols A Press Function Description Setting the TiM cscs cae 35 Menu Transparency Energy Saving HDMI Black Level Film Mode Light Effect PS50P91FD PS58P91FD Blue Screen Melody Function Help 37 Activating the Child Lock Setting the Subtitle Using the Game Mode Setting up the Parental LOCK eee 41 Screen Burn Protection cscs 43 Wall mount adjustment Sold separately PSSOP91FD PS58P91FD cece 44 Upgrading the Software oer 45 Over the Air Download 46 PC Display Setting up Your PC Software Based on Windows XP Display Modes Setting the PC Changing the Picture Size PC Mode Setting the Home theatre PC eee WISELINK Using the WISELINK Function Using the WISELINK Mode Using the Photo JPEG List
9. EMERSON 001 003 006 021 022 025 030 032034 RCA 002 017 019 021 035 041 043 057 040 047 050 052 060 063 065 066 067 068 076 069 073 SANSUI 026 FISHER 018 024 028 029 048 051 061 SANYO 018 024 FUNAI 025 SCOTT 003 047 052 067 GENERAL ELECTRIC 002 005 017 021 056 SEARS 006 018 019 024 028 029 041 048 051 GO VIDEO 002 SHARP 020 034 045 015 LG Goldstar 006 007 008 009 010 SHIMTOM 027 033 038 058 HARMAN KARDON 007 SIGNATURE 025 HITACHI 019 025 041 042 074 SONY 027 033 044 INSTANT REPLAY 021 SYLVANIA 021 025 056 059 JC PENNEY 002 007 018 019 021 026 037 041 SYMPHONIC 025 054 056 TANDY 018 025 JCL 007 008 018 021 026 037 TASHIKA 006 KENWOOD 007 008 018 026 037 TATUNG 037 KLH 070 TEAC 025 037 068 LIOYD 025 TECHNICS 021 LOGIK 038 TEKNIKA 006 021 025 031 LXI 025 TMK 066 JVC 081 082 083 TOSHIBA 003 019 029 051 052 MAGNAVOX 021 056 059 TOTEVISION 002 006 MARANTZ 007 008 018 021 026 037 062 UNITECH 002 MARTA 006 VECTOR RESEARCH 007 026 KONIA 036 VICTOR 026 ORION 073 074 075 076 VIDEO CONCEPTS 007 026 MEI 021 VIDEOSONIC 002 MEMOREX 006 021 024 025 WARDS 002 003 006 019 020 021 024 025 034 MGA 034 038 041 MIDLAND 005 YAMAHA 007 008 018 026 037 MINOLTA 019 041 075 ZENITH 023 027 033 Continued English 73 CABLE BOX Brand Code Brand Code SAMSUNG 000 001 002 003 004 005 006 007 REGENCY 015 023 Gl 041 SA 042 043 HAMLIN 003
10. Folder or file names can not exceed 128 characters If exceeded they won t function When the files stored in the USB is over 440MB if you select Delete All the TV will be abnormal You can delete it in the computer Default Guide Full Guide a Device Zoom Option A Removing the device safe The file system only supports the FAT16 32 Certain types of USB Digital camera and audio devices may not be compatible with this TV WISELINK supports USB Mass Storage Class MSC devices only MSC is the device for mass storage class bulk only transport e g thumb device flash card reader WISELINK only supports the USB Mass Storage Class device MSC MSC is a Mass Storage Class Bulk Only Transport device Examples of MSC are Thumb drives and Flash Card Readers Before connecting your device to the TV please back up your files to prevent them from damage or loss of data SAMSUNG is not responsible for any data file damage or data loss The USB hub is not supported and you cannot use a digital camera PTP Picture Transfer Protocol and USB storage device at the same time To remove a USB storage device from the TV or to turn it off if available exit WISELINK first for a proper system operation OO OF Continued English 51 Using the Remote Control Button in WISELINK Menu Button Operations eS Ri f Move the cursor and select an item SS Select the currently selected item PLAY PAUSE in
11. PiiSlideShow lt Previous Next FGOLS Option REW STOP PLAY PAUSE FF Using the Options Menu Start Slide Show or Stop Slide Show You can start or stop a Slide Show Refer to Viewing a Slide Show on pages 55 56 amp gt Normal 1 4 File 1 jpg 800x600 103 1KB 2007 1 2 WEP RE ire aging Slide Show Speed when you choose Start Slide Show you can select Slide Show Speed Refer to Slide Show Speed on page 56 Pi Pause lt Previous Next TOOLS Option Continued English 53 Zoom You can zoom into images in full screen mode Images are zoomed in in the order of x1 original size x2 and x4 Refer to Zooming In on page 56 Rotate You can rotate images in full screen mode Images are rotated in the order of 0 original state 180 270 and 90 Refer to Rotating on page 58 Background Music You can determine whether to play the configured background music Refer to Background Music On Off on page 59 Start Slide Show Adjust G Enter Background Music Setting ae You can set the background music Backoround Music Serting Refer to Background Music Setting on page 59 Flash Disk 5File s Selected fm Folder 1 Steve Love mp3 Tomas Feel So Good mp3 Jane Holiday mp3 Rachel Happy day mp3 Maritha Rain mp3 m Select Move Enter i Exit Delete You can delete a photo JPEG file Refer to Deleting the Photo files on p
12. Using the Music MP3 List eee About Anynet What is Anynett secies 64 Connecting Anynett Devices Setting Up Anynet oo eects Scanning and Switching between Anynett Devier RREGOLGING serans Ei Listening through a Home theatre Troubleshooting for Anynett s s s Appendix Teletext Feature depending on the model 69 Setting Up Your Remote Control 71 Wall Mount Kit Specifications VESA 76 How to assemble the Stand Base depending on the model Troubleshooting Specifications arieni C gt Important Note English 3 Checking Parts Owner s Instructions Remote Control Power Cord Cloth Clean AAA Batteries f q 3 If Warranty Card Cover Bottom Screws 2ea Ferrite Core for Power Cord Registration Card Refer to page 77 Ferrite Core for Safety Guide Manual Headphones Cable Antenna Cable Component Cables Audio Cables Video Cable gt Ferrite Core Power Cord Headphones Cable Hi The ferrite core is used to shield the cable from interference l pi i When connecting a cable open the ferrite core and bind cable Li round the ferrite core to secure it around the cable i i Using the Stand Base gt Two or more people should carry the PDP Never lay the PDP on the floor because of possible damage to the screen Always keep the PDP upright The PDP can rotate 20 degrees in right and left di
13. and video Y Ps PR inputs for Component DIGITAL AUDIO OUT OPTICAL ANTIN 750 Coaxial connector for Aerial Cable Network Supported modes for HDMI and Component 480i 480p 576i 576p 720p 1080i 1080p HDMI DVI 50Hz x x x 2 o 2 9 HDMI DVI 60Hz x a x x 9 A 9 Component O 0 o o 0 0 0 Connect to a Digital Audio Component According to the received audio signal optical output is selectcted by Dobly or PCM signal The level of sound can change according to received signal and sound level s difference can be PC IN AUDIO Connect to the video and audio output jack on your PC HDMI IN 1 HDMI IN 2 Connect to the HDMI jack of a device with HDMI output These inputs can also be used as a DVI connection with separate analog audio inputs An optional HDMI DVI cable will be necessary to make this connection When using the optional HDMI DVI adapter the DVI analog audio inputs on your TV allow you to receive left and right audio from your DVI device Not compatible with PC When connecting this product via HDMI or DVI to a Set Top Box DVD Player or Games Console etc make sure that it has been set to a compatible video output mode as shown in the table below Failure to observe this may result in picture distortion image breakup or no picture Do not attempt to connect the HDMI DVI connector to a PC or Laptop Graphics Card This will result in a b
14. gt Pressing the button over a photo icon shows the currently selected photo in full screen gt Pressing the button over a folder icon shows the JPEG files included in the folder gt While a full screen is displayed lt or gt button will let you see another photo image in the same folder gt Press the PLAY PAUSE button when a photo icon is selected to start a Slide Show Now amp Next Guide Default Guide Full Guide 4 Toexit WISELINK mode press the EXIT button on the ec aa OOT File 1 2007 1 2 remote control JD espe E gt Moving to a photo may take a few seconds because the ane as file needs to be loaded At this point the icon will appear gt This menu shows only the files whose extension is jpeg or jpg Files with other formats such as gif or tiff will not USB Device Zoom Option be displayed gt Folders are displayed first and they are followed by all 1 4 File 1 jpg 800x600 103 1KB 2007 1 2 JPEG files in the current folder The folders and JPEG files are sorted in alphabetical order gt Ifthe photo is displayed in full screen you can zoom in and out or rotate the photo on the screen Refer to pages 56 57 gt Ifthe size of a photo file is too big the playing of the background music may be interrupted intermittently When Background Music is On See page 59 gt Press the WISELINK button on the remote control to turnon ING SS E the WISELINK mode l WISELINK CHLIST FAV CH REC ia lied a
15. i PDP TELEVISION PLASMA DISPLAY PANEL Owner s Instructions Before operating the unit please read this manual thoroughly and retain it for future reference ON SCREEN MENUS Picture In Picture PIP Energy Saving TELETEXT option tene gt SRS TruSurround XT DNie Digital Natural Image engine Register your product at www samsung com global register Record your Model and Serial number here for future reference Model Serial No User Instructions Screen Image retention Do not display a still image such as on a video game or when hooking up a PC to this PDP on the plasma monitor panel for more than 2 hours as it can cause screen image retention This image retention is also known as screen burn To avoid such image retention reduce the degree of brightness and contrast of the screen when displaying a still image Height The PDP can normally operate only under 2000m in height It might abnormally function at a place over 2000m in height so do not install and operate there Heat on the top of the PDP TV The top side of the product may be hot after long period of use as heat dissipates from the panel through the vent hole in the upper part of the product This is normal and does not indicate any defect or operation failure of the product However children should be prevented from touching the upper part of the product The product is making a cracking noise A cracking noise may
16. 024 031 SCIENTIFIC ATLAN 042 043 HITACHI 025 030 SPRUCER 022 JERROLD 038 039 STARGATE 2000 036 MACOM 025 030 SYLVANIA 016 MAGNAVOX 019 023 028 TEXSCAN 016 OAK 026 TOCOM 032 PANASONIC 003 022 027 037 044 UNIVERSAL 033 034 PHILIPS 019 021 023 028 VIEWSTAR 019 021 023 028 PIONEER 004 018 020 044 WARNER AMEX 046 RCA 014 022 040 ZENITH 017 029 035 037 045 REGAL 003 SAMSUNG SET TOP BOX Product Code Ground wave STB 000 001 002 008 013 CABLE STB 000 004 008 013 Satellite STB 000 003 008 013 SET TOP BOX Brand Code Brand Code ALPHASTAR 023 LG Goldstar 044 073 ANAM 043 MAGNAVOX 016 021 036 038 039 040 041 042 CHANNEL MASTER 018 034 MEMOREX 016 CROSSDIGITAL 019 MOTOROLA 064 CHAPARRAL 035 MACOM 018 DIRECT TV 015 016 017 019 022 045 060 MITSUBISHI 015 061 062 065 066 067 068 NEXT LEVEL 047 048 064 DAEWOO 074 PHILIPS 015 016 017 021 033 036 038 039 DISH NETWORK SYSTEM 069 070 040 041 042 067 DISHPRO 069 PRIMESTAR 046 049 050 063 DRAKE 018 024 032 PANASONIC 058 059 061 062 DX ANTENNA 027 PAYSAT 016 ECHOSTAR 025 069 070 071 PROSCAN 065 066 EXPRESSVU 069 RCA 051 052 053 065 066 GOl 069 RADIOSHACK 064 GE 065 REALISTIC 057 GENERAL INSTRUMENT 046 047 048 063 064 STS 020 027 HTS 069 STAR TRAK 026 HOME CABLE 056 SKY 031 HITACHI 022 SKY LIFE 005 006 007 HUGHES NETWORK 015 017 SHACK 064 IQ 020 STAR CHOICE 064 IQ PRISM 020 SONY 054 060 JANEIL 059 TOSHIBA 015 017 028 029 030 072 JERROID 063 ULTIMATE TV 060 066 JVC 069 070 UNIDEN 016 021 037 055 056 057 ZENI
17. Mode Current picture values return to default settings eo ee gt English 27 Colour Size Digital NR Active Colour DNle Picture Reset Colour Tint G R Colour Tone d Settings Si Digital NR Picture Reset Picture Reset Select the option for picture reset ResetAll Reset Picture Mode lt gt Move G Enter D Return Configuring Detailed Settings on the Picture You can set detailed picture settings Tint GIR G50 R50 14 Press the MENU button to display the menu Colour Tone Cool1 2 Press the ENTER OK button to select Picture Detaled Settings he Settings a 3 Press the A or Y button to select Detailed Settings 7 7 then press the ENTER OK button yy eee 4 Select the required option by pressing the A or Y button Coe then press the ENTER OK button Aa golour Available options Black Adjust Dynamic Contrast R Gamma Colour Space White Balance My Colour Control Edge Enhancement 5 When you are satisfied with your setting press the ENTERIOK button Detailed Settings 6 Press the EXIT button to exit gt When the picture mode is set to Standard or Movie Black Adjust Medium D Return A 3 Dynamic Contrast Medium Detailed Settings can be selected G i amma Kaai gt If DNle is set to Off and the picture mode is in Dynamic Colour Space Wide or Standard mode the Detailed Settings cannot be White Balance selected My Colour Control Black Adjust Of
18. Play or pause the Slide Show or MP3 file RETURN Return to the previous menu TOOLS a Run various functions from the Photo and Music menus ri Stop the current slide show or MP3 file a e Page Up or Down file list item Using the WISELINK Mode 1 Press the MENU button to display the menu Press the A or Y button to select Guide then press the lt ENTER OK button a LE 3 Press the ENTER OK button to select WISELINK 4 Pressthe A or Y button to select Photo or Music then em Ful Gulce press the ENTER OK button Now amp Next Guide ine oe or music files saved on the storage device are Default Guide Full Guide 5 To exit WISELINK mode press the EXIT button on the remote control e e Folder annen 2007 112 m A Ae LE J etp 2007 1 2 1G File 2jpg 2007 1 2 1 File 3 jpg 2007 1 2 0 File4 jpg 2007 1 2 Device Zoom Option gt Press the WISELINK button on the remote control to turn on rl wae or aE the WISELINK mode i WISELINK CHLIST FAV CH REC REW STOP PLAY PAUSE FF English 52 Using the Photo JPEG List You can play back the JPEG files saved on a memory device in various ways 14 After switching the mode to WISELINK select a memory device that you have installed Refer to page 51 52 2 Press the ENTER OK button to select Photo JPEG files and existing folders are displayed 3 Press the A or V button to select a photo then press the EX Full Guide ENTER OK button
19. background If you wish to continue viewing the poor picture you must set the Blue Screen to Off Melody Off Low Medium High The TV power on off melody sound can be adjusted Function Help On Off Displays help on the menu functions gt The Function Help default setting is On PC Home theatre PC Off HDMI Black Level Normal Film Mode Off English 37 Activating the Child Lock This feature allows you to prevent unauthorized users i einacnvaied such as children from watching unsuitable programmes by muting out video and audio Child Lock cannot be released using the buttons on the side Only the remote control can release the Child Lock setting so keep the remote control away from children 1 Press the MENU button to display the menu Inactivated 2 Press the A or Y button to select Setup then press the E amp Menu Transparency Medium ENTER OK button Energy Saving Off 3 Press the A or V button to select Child Lock 4 Press the ENTER OK button to select On or Off Press the HometheatrePC Off ENTER OK button 5 Press the A or V button to select Channel then press the ENTER OK button and select the channels you want to lock then press the ENTER OK button Child Lock 6 Press the A or Y button to select Lock then press the Chant ENTER OK button to select Unlocked or Locked 7 Repeat steps for each channel to be locked or unlocked 8 Press the EXIT button to exit gt While viewing a Anal
20. buttons Press the EXIT button to exit gt If you press an arrow button when no OSD is displayed on the TV screen the Adjustment screen appears gt When you turn the power off your TV moves to the initial installation position When you turn the power on your TV moves to the last remembered position you adjusted Using the remote Control Buttons i 6 es Light Effect Blue Screen Melody Screen Burn Protection Anynet HDMI CEC Setup SW Upgrade Function Help Off Position1 Position 1 Button Operations A i a Tilt Up Tilt Down Move Sa adjustment right Move left INFO Moves to the initial Reset installation position Remembering Remembers 3 positions the position and moving to the remembered position Red Green Yellow Yellow buttons position using these 3 colour buttons with the Red Green and INFO Wettig lt gt Adjust J Exit Moves to the remembered gt For installation refer to the Installation Manual provided gt For product installation and the installation and moving of the wall mount make sure to consult a specialized installation company gt This installation manual is to be used when attaching the wall mount to a wall When attaching to other building materials please contact your nearest dealer English 44 Upgrading the Software Samsung may offer upgrade
21. plasma This phenomenon may continue for 3 5 minutes if there is no upgrade signal But this phenomenon may Software Information Alternative Software X SAFFDAU0 XXXX 3 j A Old Version continue for more than 1 hour if there is new software version After upgrade is completed your TV will be Switch Default Software Move S Enter O Return turned off automatically If you don t want this process select Off by pressing the A or Y button Press the Software Information ENTERIOK button Current Software T SAFFDAUO XXXX Alternative Software X SAFFDAU0 XXXX Old Version New Default Confirm D Return Software Upgrade Software Information Manual Upgrade Standby Mode Upgrade Move Enter D Return SWuUpgrade Scan Searching for Upgrade English 46 Setting up Your PC Software Based on Windows XP The Windows display settings for a typical computer Display Properties are shown below But the actual screens on your PC will probably be different depending upon your particular version of Windows and your particular video card But even if your actual screens look different the same basic set up information will apply in almost all cases If not contact your mne computer manufacturer or Samsung Dealer Active Window ED 1 Right click the mouse on the Windows Desktop then click on w Properties The Display Properties will be displayed 2 Click on Settings tab then set the Display Mode
22. six categories Part Contents Selected page number Broadcasting channel identity i Current page number or search indications aee D Date and time H Text i Status information E FASTEXT information mMOUOWD gt Teletext information is often divided between several pages displayed in sequence which can be accessed by Entering the page number Selecting a title in a list Selecting a coloured heading FASTEXT system gt Press the RETURN button to exit from the teletext display RETURN COLOR BUTTON gt Ds E a English 70 Setting Up Your Remote Control After it has been set up properly your remote control can operate in five different modes TV VCR Cable DVD or Set Top Box Pressing the corresponding button on the remote control allows you to switch between these modes and control whichever piece of equipment you choose gt The remote control might not be compatible with all DVD Players VCRs Cable boxes and Set Top Boxes ORESET SAMSUNG yy SET RESET SAMSUNG i Setting Up the Remote to Operate Your VCR 1 Turn off your VCR Press the VCR button on your TV s remote control 2 3 Press the SET button on your TV s remote control i 4 Using the number buttons on your remote control enter three digits of the VCR code listed on page 73 of this manual for your brand of VCR Make sure you ent
23. the DVD Recorder appears Starts a recording immediately This menu works only for a device Record supporting recording Allows reserving a recording Timer Recording This menu works only for a Pievi supporting recording M Stop Recording Stops one Receiver Sound is output through the receiver home theatre Continued English 66 TV Remote Control Buttons Available in Anynet Mode Device Type Operating Status Available Buttons After switching to the Numeric buttons device when the menu of A lt gt ENTER buttons the corresponding device is Colour buttons Anynett Deviee displayed on the screen EXIT button y lt 4 lt Backward search After switching to the device gt gt Forward search while playing a file m Stop gt il Play Pause After switching to the device Device with built in Tuner when you are watching a TV CH A button program 3 3 ge VOL button Audio Device When Receiver is activated MUTE button gt The Anynet function only works when the remote control is set to TV gt The REC button works only in View TV status gt You cannot control Anynet devices using the buttons on the side of the TV You can control Anynet devices only using the TV remote control gt The TV remote control may not work under certain conditions In this case re select the Anynet device gt The Anynet functions don t operate for the products from other
24. you find the best position with the strongest signal 5 Press the EXIT button to exit Enter D Return Storing Channels Automatically You can scan for the frequency ranges available to you availability depends on your country Channel List Automatically allocated programme numbers may not _ __ gt correspond to actual or desired programme numbers However you can sort numbers manually and clear any Manual Store i channels you do not wish to watch i Fine Tune 14 Press the MENU button to display the menu Signal Strength 2 Press the A or V button to select Channel then press the LNA ENTER OK button 3 Press the A or V button to select Auto Store then press the ENTER OK button 4 Press the ENTER OK button again to start the search The search will end automatically gt To stop the search before it has finished press the MENU or the ENTER OK button English 16 Storing Channels Manually You can store television channels including those Chonnelitet received via cable networks Auto Store When storing channels manually you can choose _ Whether or not to store each of the channels found eS The programme number of each stored channel which you Fine Tune is wish to identify Signal Strength 1 Press the MENU button to display the menu LNA Press the A or Y button to select Channel then press P the ENTER OK button 3 Press the A or butt
25. 0 x 960 60 000 60 000 108 000 1280 x 1024 63 981 60 020 108 000 1280 x 1024 74 620 70 000 1 28 943 1280 x 1024 79 976 75 025 135 000 1600 x 1200 75 000 60 000 162 000 1920 x 1080 66 587 59 934 138 500 HDMI DVI Input a Horizontal Vertical Pixel Clock Sync Polarity mode Redon Frequency kHz Frequency Hz Frequency MHz HIV 640 x 350 31 469 70 086 25 175 IBM 640 x 480 31 469 59 940 25 175 l 720 x 400 31 469 70 087 28 322 800 x 600 37 879 60 317 40 000 VESA 1024 x 768 48 364 60 000 65 000 1280 x 1024 63 981 60 020 108 000 1920 x 1080 66 587 59 934 138 500 The interlace mode is not supported The set might operate abnormally if a non standard video format is selected Separate and Composite modes are supported SOG is not supported English 48 Setting the PC gt Preset to the PC mode by pressing the SOURCE button eee a 1 Press the MENU button to display the menu Energy Saving Press the A or V button to select Setup then press the ENTERIOK button ne 3 Press the A or Y button to select PC then press the Flometheate PE ENTER OK button P EN 4 Select the required option by pressing the A or Y button 7 then press the ENTER OK button EA Aemet HE Available options Image Lock Position Auto Blue Screen On Adjustment Image Reset Melody Medium 5 When you are satisfied with your setting press the ENTER OK button 6 Press the EXIT button to exit
26. 07 1 2 2007 1 2 2007 1 2 2007 1 2 2007 1 2 Option PiiSlide Show TOOLS Start Slide Show Dynamic Standard Move Adjust Enter 2007 1 2 2007 1 2 2007 1 2 Option REC Pil Slide Show TOOLS Slide Show Information amic Standard Move GEnter Background Music Setting Flash Disk fm Folder 1 5File s Selected Steve Love mp3 Tomas Feel So Good mp3 Jane Holiday mp3 Rachel Happy day mp3 Maritha Rain mp3 m Select Move Save S Return Continued gt Press the WISELINK button on the remote control to turn on the WISELINK mode Deleting the Photo files WISELINK CHLIST FAV CH REC REW STOP You can delete photo JPEG files saved on a USB storage device 1 After switching the mode to WISELINK select a memory device that you have installed Refer to page 51 52 2 Press the ENTER OK button to select Photo JPEG files and existing folders are displayed 3 Press the A or V button to select a photo you want to delete and then press the blue button 4 Press the A or Y button to select Delete or Delete All and then press the ENTER OK button gt Ifyou select Delete only the selected photo will be deleted gt If you select Delete All al deleted 5 Press the lt or gt button to select Yes and press the ENTER OK button gt The photo will be deleted gt Ifyou select No the deletion is cancelled 6 To exit WISELINK mode press the EXIT button on
27. 2 Press the A or V button to select Receiver press the lt or gt button to select to On Now you can listen to sound through the Home theatre receiver Press the EXIT button to exit gt gt When the receiver home theatre is set to On you can hear sound output from the TV s Optical jack When the TV is displaying a DTV air signal the TV will send out 5 1 channel sound to the Home theatre receiver When the source is a digital component such as a DVD and is connected to the TV via HDMI only 2 channel sound will be heard from the Home Theatre receiver gt If your Home Theatre receiver supports audio only it may not appear in the device list gt The receiver will work when you have properly connected the Optical IN jack of the receiver to the Optical Out jack of the TV gt gt When using the WISELINK feature sound may not Output properiy through the receiver gt gt When listening through the receiver there are restrictions for using the PIP and audio related MTS Preferred language menus Troubleshooting for Anynet Symptom Solution Anynet does not work m Check if the device is an Anynet device The Anynet system supports Anynet devices only Connect only one receiver home theatre Check if the Anynet device power cord is properly connected Check the Anynet device s Video Audio HDMI cable connections Check whether the TV remote control is in TV mode Check whether it is Anynet exclusive remote con
28. 4 HDMIIN3 Headphones jack Connect to the HDMI jack of a device with You can connect a set of headphones if you HDMI output wish to watch a television programme without S VIDEO or VIDEO AUDIO L R disturbing the other people in the room Video S Video or Video and audio inputs for gt Prolonged use of headphones at a high external devices such as a camcorder or VCR volume may damage your hearing Cable Television Network gt The product colour and shape may vary depending on the model Whenever you connect an audio or video system to your set ensure that all elements are switched off When connecting an external device match the colour of the connection terminal to the cable Continued English 6 POWER IN Connect the supplied power cord Connecting external Audio Devices Connect RCA audio signals from the TV to an external source such as Audio equipment SERVICE Connector for service Connect the serial jack between the electro motion wall mount bracket and your TV when you want to adjust the TV viewing angle using your remote control VIDEO AUDIO L R Video and audio inputs for external devices such as a camcorder or VCR COMPONENT IN 1 COMPONENT IN 2 Audio AUDIO L R
29. 62 4 Press the PLAY PAUSE button while playing an MP3 file to pause the file Press the STOP button to stop playback Pipause Previous gt Next G0LS Option CE List 5 To exit WISELINK mode press the EXIT button on the remote control gt This menu shows only the files whose extension is mp3 Files with other extensions are not displayed even if they have been saved on the same memory device gt The selected file is displayed on the top of the screen with its playing time gt To adjust the music volume press the VOL or VOL button on the remote control To mute the sound press the MUTE button on the remote control gt To move to the music list while playing a music file press the WISELINK button gt Press the WISELINK button on the remote control to turn on i M CJZ WI E f the WISELINK mode i WISELINK CHLIST FAV CH REC REW STOP PLAY PAUSE FF Continued English 61 Playing a Selected Music File 1 Inthe Music list press the A or V button to select a music file and then press the yellow button SB mron oor gt The lt gt mark appears to the left of the selected z dd aalsa music vV J Steve Love mp3 2007 1 2 J Jane Holiday mp3 2007 1 2 gt Repeat the above operation to select multiple music files 2 Press the blue button then press the ENTER OK button to select Play selected File 3 To exit WISELINK mode press the EXIT button on the remote control Flash Disk Device Zoom Sele
30. Clock Manually 1 Press the MENU button to display the menu 2 Press the A or Y button to select Setup then press the ENTER OK button 3 Press the A or V button to select Clock then press the ENTER OK button 4 Press the ENTER OK button to select Clock Mode 5 Press the A or V button to select Manual then press the ENTER OK button 6 Press the A or Y button to select Clock Set then press the ENTER OK button 7 Press the lt or gt button to move to Month Day Year Hour or Minute am pm Set the date and time you want by pressing the A or Y button then press the ENTER OK button 8 Press the EXIT button to exit gt The current time will appear every time you press the INFO button gt You can set the Month Day Year Hour and Minute directly by pressing the number buttons on the remote control English 35 Plug amp Play lt Sleep Timer Off X Time nactivatec r Child Lock Subtitle aa Manual Move G Enter D Return Time Zone QueenSland South Australia West Australia Tasmania Move Enter D Return Clock Mode f Auto Manual Move G Enter D Return Clock Set Os fs ta CA rn a OT es lt gt Move Adjust Enter D Return RETURN INFO Anynet Lee OE arrer COLOBRUTION m al Continued Setting the On Off Timer Use this feature to set the TV to turn on or off at a desired time 1 Press the MEN
31. ENWOOD 051 108 109 TVIEW 072 KISS 073 TOKAI 073 KONKA 059 100 106 107 TEAC 096 KLH 074 075 TECHWOOD 097 LG Goldstar 025 031 TREDEX 098 099 101 LOEWE 057 URBAN CONCEPTS 076 LASONIC 058 VENTURER 075 MOBILE AUTHORITY 054 VOCOPRO 102 MEMOREX 055 YAMAHA 032 063 MALATA 056 YAMAKAWA 040 073 MAGNAVOX 076 093 XWAVE 103 MINTEK 074 094 ZENITH 076 121 MONYKA 073 English 75 Wall Mount Kit Specifications VESA Install your wall mount on a solid wall perpendicular to the floor When attaching to other building materials please contact your nearest dealer If installed on a ceiling or slanted wall it may fall and result in severe personal injury Product Family inch VESA Spec A B Standard Screw Quantity 23 26 200 100 M4 32 40 200 200 M6 46 52 600 400 LCD TV 4 57 700 400 No VESA No M8 57 70 800 400 80 1400 800 42 50 600 400 4 55 70 800 400 PDP TV M8 63 No VESA 6 80 1400 800 4 gt gt We provided the standard dimensions for wall mount kits as shown in the table above gt When purchasing our wall mount kit a detailed installation manual and all parts necessary for assembly are provided gt Do not use screws longer than the standard dimension as they may cause damage to the inside of the TV set gt For wall mounts that do not comply with the VESA standard screw specifications the length of the screws may differ depending on their specificatio
32. Fine Tune Signal Strength LNA Digital 2 7Digital 3 C1 7 3 c4 c5 c6 c7 m Select Option Delete Add to Favourite Timer Viewing Channel Name Edit m Select Option Channel Name Edit Move Enter D Return Fine Tuning Channel Reception If the reception is clear you do not have to fine tune the Auto Store channel as this is done automatically during the search Manual Store and store operation If the signal is weak or distorted you may have to fine tune the channel manually 1 Press the MENU button to display the menu 2 Press the A or V button to select Channel then press the ENTER OK button 3 Press the A or V button to select Fine Tune then press the ENTER OK button 4 To obtain a sharp and clear picture and good sound quality press the lt or gt button until you reach the optimal setting Press the ENTER OK button Fine Tune gt To reset the fine tuning to 0 select Reset by pressing the A or Y button Press the ENTER OK button 5 Press the EXIT button to exit gt Fine tuned channels that have been saved are Reset marked with an asterisk on the right hand side of Move lt gt Adjust Save D Return the channel number in the channel banner Fine Tune Reset 4 Move lt gt Adjust amp Save D Return Fine Tune ATV6 fl eee 0 Move Enter D Return English 24 LNA Low Noise Amplifier This function is very useful in the
33. Move Adjust Enter D Return Setting the Sleep Timer The sleep timer automatically shuts off the TV after a preset time 30 60 90 120 150 and 180 minutes 14 Press the MENU button to display the menu 2 Press the A or Y button to select Setup then press the ENTER OK button 3 Press the A or V button to select Sleep Timer then i press the ENTER OK button 3 aon 4 Pressthe A or Y button to select the minute then press P Sorin the ENTER OK button e ue 1 ck 120min To cancel the set sleep timer 150min Press the A or Y button to select Off then press the Ga 180min ENTER OK button 5 Press the EXIT button to exit English 36 Menu Transparency Energy Saving HDMI Black Level Film Mode Light Effectiessopo1rp pssepo1Fp Blue Screen Melody Function Help ocr Press the MENU button to display the menu Ga Press the A or Y button to select Setup then press the Parental Lock Select the required option by pressing the A or Y button then press the ENTER OK button SEIU oi Available options Menu Transparency Energy Saving HDMI Black Level Film Mode Light Effect Blue Screen Melody Function Help ld are satisfied with your setting press the ENTER a utton Press the EXIT button to exit AA inae Menu Transparency High Medium Low Adjusts the transparency of the menu screen Energy Saving Off Low Medium High This feature adjusts the screen brightness depending on the sur
34. OK button The Reserve a Program Timer Viewing screen appears 6 Press the A lt P buttons to reserve a program and then press the ENTER OK button Reserving a program has been completed Press the EXIT button to exit gt You can also reserve a program in the All Channels or Favourite menus using the same procedures gt For information on how to confirm a viewing reservation refer to page 22 n gt You can select these options simply by pressing the CH LIST button on the remote control Digital Program Guide and Viewing Reservation When a digital channel is selected and you press the gt button the Program Guide for the channel appears You can reserve a program according to the procedures described above A program currently being broadcast A reserved program English 21 Q fy Channel ist D Auto Store Manual Store Fine Tune Signal Strength LNA 7Digital 1 Delete from Favourite Timer Viewing annel Name Edit Zoom Select Option Timer Viewing Antenna Channel Repeat 2 once Date Start Time 2007 01 10 10 09am Move Adjust Enter D Return 2007 2 3 v7Digital1 1 30 am 7Digital 2 Digital Zoom Option Watch Continued Confirming a Viewing Reservation You can view modify or delete a reservation 1 Press the MENU button to display the menu 2 Press the A or V button to select Channel then press the ENTER OK button Jc 3 Pr
35. Position cannot be selected gt Ifthe PIP window is set to Double Window OO or Double Wide CJ mode the screen size or alignment may slightly differ depending on the signal Size type Changing the PIP Channel z z Size 6 Press the A or V button to select Channel then press Position the ENTER OK button Press the A or Y button at the bottom of the remote to AME ARo avs _ select the desired channel in the PIP window then press the ENTER OK button gt The channel can be active when the sub picture is set to TV 7 Press the EXIT button to exit English 32 Sound Features 1 Press the MENU button to display the menu Press the A or Y button to select Sound then press the ENTERI OK button Mode ns CUStOM Ds euso 3 Select the required option by pressing the A or Y button i then press the ENTER OK button pa ouae Available options Mode Equalizer SRS TruSurround SRS TruSurround XT LOR XT Audio Language Auto Volume Internal Mute Audio Language sie English Sound Select Digital Format Sound Reset g pia eNom o 4 When you are satisfied with your setting press the co ates me ENTER OK button Za states vines 5 Press the EXIT button to exit nace Mode Standard Music Movie Speech Custom Saal You can select the type of special sound effect to be used sme when watching a given broadcast Mode Custom Equalizer Balance 100Hz 500Hz 1kHz 2kHz 4kHz Balance L mmm R ai ad XT Off 0 a ru
36. Recorder PC Internet TV Recv Interactive TV Recv Edit Name VOD STB TV 6 Press the EXIT button to exit AVA gt gt When a PC with a resolution of 1920 x 1080 60Hz e is connected to the HDMI IN 1 port you should set SAEED the HDMI1 mode to PC in the Source List of the Component Input mode If the HDMI1 mode is not PC it works Component2 depending on the TV setting PC HDMI1 Move Enter D Return Edit Name VCR DVD D VHS Cable STB HD STB Move Enter Return English 14 Setting the Guide You can set the guide as your preference 14 Press the MENU button to display the menu 2 Press the A or Y button to select Guide Press the gt gt WEEUK ENER OR non EE oe 3 Select your required guide Now amp Next Guide or Full r Guide by pressing the A o Y button cid E 4 Press the ENTER OK button Default Guide Full Guide 5 Select a programme of your choice by pressing the A Y lt or gt button 6 Press the INFO button to display information about the highlighted programme 7 Press the red button to exchange Now amp Next Guide or Full Guide d 8 Press the EXIT button or blue button to exit pc TODA sania 00 AM 6 00 International news and weather Including interviews with ne Today AM6 00 AM7 00 AMT 00 AM8 00 a 25 7 Digital SUNRISE 26 THD Digital NBC TODAY SUNRISE 27 TDigital NBC TODAY SUNRISE 28 7Digital2 NBC TODAY SUNRISE 32 7Digital3 NBC TODAY SUNRISE 33 7 G
37. Surroun n eee ee eee TruSurround XT is a patented SRS technology that solves ae A i 7 the problem of playing 5 1 multichannel content over two speakers TruSurround delivers a compelling virtual sues 2 surround sound experience through any two speaker 4kHz e playback system including internal television speakers It m is fully compatible with all multichannel formats pa SA EE Sy gt TruSurround XT SRS and c Symbol are trademarks of SRS Labs Inc TruSurround XT technology is incorporated under license from SRS Labs Inc Audio Language i 7 You can change the default value for audio languages Displays the language i SRS i information for the incoming stream A i gt While viewing a Digital channel the Audio Language function can be selected Auto Volume Off On Each broadcasting station has its own signal conditions and so it is not easy to adjust the volume every time the channel is changed This feature lets you automatically adjust the volume of the desired channel by lowering the sound output when the modulation signal is high or by raising the sound output when the modulation signal is low Internal Mute Off On If you want to hear the sound through separate speakers cancel the internal amplifier gt gt The A and MUTE buttons do not operate when the Internal Mute is set to On gt gt When Internal Mute is set to On the Sound menus except for Sound Select in PIP mode cannot be adjusted S
38. TH 024 031 068 English 74 Continued SAMSUNG DVD Product Code Product Code DVD 000 001 002 Home Theatre VCR COMBO 014 015 016 DVDR 003 004 HDD Record COMBO 017 BD Record 005 006 TWIN TRAY COMBO 018 VCR COMBO 007 008 009 010 011 STB DVD COMBO 019 VCR Record 012 DVD Receiver 020 DHR COMBO 013 AV Receiver 021 DVD Brand Code Brand Code ANAM 030 NORCENT 048 049 050 AUDIOVOX 075 NEXT BASE 052 AUDIOLOGIC 085 NEC 053 ANABA 072 NANTAUS 144 APEX DIGITAL 070 071 074 086 083 084 088 NESA 074 111 112 OPTOMEDIA ELECTRONICS 105 AIWA 114 OPTIVIEW 072 BROKSONIC 062 ONKYO 076 092 119 BLAUPUNKT 074 PHILCO 044 045 B amp K 122 123 PRINCETON 046 047 CURTIS MATHES 027 PROSCAN 023 CYBER HOME 065 077 078 079 082 PANASONIC 024 034 124 134 136 137 138 CLARION 080 125 PHILIPS 036 076 CIRRUS 081 ROTEL 117 118 CINEVISION 095 RIO 120 DAEWOO 066 RCA 023 035 074 075 131 132 DENON 146 RAITE 073 FARENHEIT 067 068 ROWA 038 FISHER 090 SAMPO 104 GPX 060 SONY 026 029 126 127 128 129 GO VIDEO 061 089 133 135 130 141 GE 069 074 SHERWOOD 039 041 GREENHILL 074 SVA 042 HITACHI 064 113 SYLVANIA 043 093 HITEKER 071 SHARP 140 HOYO 073 SANSUI 062 HARMAN KARDON 091 110 SANYO 062 IRT 089 SHINSONIC 094 INTEGRA 092 SANYO 090 JBL 091 THOMSON 145 JVC 022 033 115 116 TOSHIBA 028 062 076 JATON 073 TECHNICS 139 K
39. U button to display the menu 2 Press the A or Y button to select Setup then press the ENTER OK button 3 Press the A or V button to select Timer 1 then press the ENTER OK button The Timer 1 menu is displayed Clock 12 00am Sleep Timer Off T i Timer 2 Inactivated Timer 3 Inactivated 4 Pressthe lt or gt button to select the required item cidro below Subtitle Press the A or W button to adjust to the setting satisfied Game Mode Off 5 Press the EXIT button to exit Paone On Timer Select Hour Minute am pm and No Yes Menu Transparency Medium To activate timer with the setting satisfied set to Yes Off Timer Select Hour Minute am pm and No Yes To activate timer with the setting satisfied set to Yes On Timer Repeat Select Once Everyday Mon Fri Mon Sat or wwMlinute a ANN Activation Sat Sun Volume Select the required volume level Off Timer Contents When the On Time is active you can turn on alou a specific channel or play back contents such as photo or audio files Make sure that a USB device is connected to your TV wBEpEata VOUE es COMMS ey gt Auto Power Off When you set the timer On the TV will eventually turn off 4 Move Adjust G Enter Retum if no controls are operated for 3 hours after the TV was turned on by timer This function is only available in timer On mode and prevents overheating which may occur if a TV is on for too long time Contents 4
40. age 60 Ay Povouwantto delete fle File 1jpg Continued English 54 Picture Setting You can set the Picture mode Refer to on page 27 Sound Setting You can set the Sound mode Refer to on page 33 Move o Information OES PEN Position dtv usb sda Folder 1 File 1 jpg The photo file information including the order of the file in the Name File 1 jpg current directory the name the size the resolution and the Size 103 1KB date modified is displayed Resolution 800x600 Date Jan 1 2007 Screen Saver Select to set the waiting time before the screen saver is run when no button is pressed You can select from 1min 5min or 10min gt To prevent a residual image on the screen the time to run the Screen Saver is set to 5min by default Users can k a m Folder 2007 1 2 change the setting to Off 5min or 10min according to po Omm SOAP user requirements 1 File2jpg 2007 1 2 iO File 3 jpg 2007 1 2 W File 4 jpg 2007 1 2 Safe Remove You can remove from the WISELINK Viewing a Slide Show 1 After switching the mode to WISELINK select a memory device that you have installed Refer to page 51 52 Device Zoom Select Option Pll Slide Show Ma Folder 2 Press the ENTER OK button to select Photo O Fie tpg ar JPEG files and existing folders are displayed Start Slide Show 3 Press the A or Y button to select a photo then press bess Bee the blue button to display the option View S
41. al screen press it once again O mode Press to select the teletext mode LIST FLOF i If you press it in the LIST mode it switches into the List save mode In the List save mode you can save teletext page into list using the store button sub page Used to display the available sub page page up Used to display the next teletext page page down Used to display the previous teletext page cancel Used to display the broadcast when searching for a page aaa a reveal Used to display the hidden text answers to quiz games for example To display normal screen press it again Coloured buttons red green yellow blue If the FASTEXT system is used by a broadcasting company the different topics covered on a teletext page are colour coded and can be selected by pressing the coloured buttons Press one of them corresponding to the required The page is displayed with other coloured information that can be selected in the same way To display the previous or next page press the corresponding coloured button 12 hold Used to hold the display on a given page if the selected page is linked with several secondary pages which follow on automatically To resume press it again store Used to store the teletext pages SAMSUNG e 6600609 86 gt You can change teletext pages by pressing the numeric buttons on the remote control H Continued English 69 The teletext pages are organized according to
42. annel Press to switch to your favourite channels Records for Live Broadcasting VCR DVD Function Rewind Stop Play Pause Fast Forward Next channel Previous channel Exit the on screen menu Control the cursor in the menu Use to see information on the current broadcast TOOLS Use to quickly select frequently used functions Anynet Runs the Anynett view functions and sets up Anynet devices Picture In Picture On Off Picture effect selection Digital subtitle display Picture freeze If your remote control is not functioning properly take out the batteries and press the reset button for about 2 3 seconds Reinsert the batteries and try using the remote control again 60O 88 Teletext Functions Teletext index Exit from the teletext display depending on the model Fastext topic selection Teletext display mix both teletext information and the normal broadcast Teletext size Teletext mode selection LIST FLOF Teletext sub page P Teletext next page P Teletext previous page Teletext cancel Teletext reveal Teletext hold Teletext store OOOO 86 OO OO OO English 8 N d g SNMSUNS gt This is a special remote control for the visually impaired persons and has Braille points on the H i i 1 Hy i 1 i h i i d i H EDY i i Q Zz ia f OR NOOA Aroer i WS i i 1 7 SZE PODE Se O 22 z f ae DA L NE oj Sc eo
43. ated Anynet HDMI CEC Setup Anynet HDMI CEC off O _ Moe Enter D Return Setting an Anynet Device to turn Off Automatically when the TV is Turned Off 3 Press the A or V button to select Auto Turn Off then press the ENTERIOK button oregon eee SEME 4 Press the A or Y button to select On then press the Anynet HDMI CEC off ENTER OK button Auto Turn Off 5 Wma d gt The Auto Turn Off function is enabled gt Ifyou select Off the Auto Turn Off function is cancelled Ee eal Ee TR Press the EXIT button to exit as kai faa gt The active source on the TV remote must be set to TV to use the Anynet function gt If you set the Anynet HDMI CEC to On the Device List menu appears when you press the TOOLS button on the remote control gt If you set Auto Turn Off to On connected external devices are also turned off when the TV is turned off However if the device is recording it may not be turned off English 65 Scanning and Switching between Anynet Devices 1 Press the Anynet button Press the ENTER OK button to select Device List gt Anynet devices connected to the TV are listed Device List gt lf you cannot find a device you want press the red button HEB Recording DVD to scan for devices HEB DVD Menu 2 Press the A or Y button to select to a particular device and HBS DVD Operation press the ENTER OK button It is switched to the selected Tenn EO device 7 Se Pict
44. available channels 1 Y THD Digital i 7Digital 1 3 6 Press the A or Y button to select a channel to view then aiNaaNNE OSH press the ENTER OK button 2 KA You can watch the selected channel a ATV3 C4 gt You can press Number buttons on Remote control for Da direct channel access press the same Number button again to switch between digital channel and ATV channel Zom Select Option 1 Y7HD Digital 4 2 7Digital 1 3 7Digital 2 4 7Digital 3 ATVO Ct ATVI c2 ATV2 c3 ATV3 c4 ATV4 c5 Zoom T gt You can select these options simply by pressing the CH LIST TT i a ae eel button on the remote control i H REW STO IPAUSE Using the Colour buttons on the Remote with the Channel List Green Zoom Enlarges or shrinks a channel number Yellow Select Selects multiple channel lists Blue Option Displays the Add or Delete Add Favourite or Delete Favourite Timer Viewing and Channel Name Edit menus gt Agray coloured channel refers to a deleted channel The Add menu only appears for deleted channels gt If you select multiple channel include favourite channels delete channel etc channels and other channels you can choose Add to Favourite or Delete from Favourite or Add or Deselect All etc HD Digi Eav 2 Digian Delete v Digitala Add to Favourite Delete from Favourite Deselect All SjSUUEYD Ily Zoom Select Option Continued
45. can set the month day year hour and minute directly by pressing the number buttons on the remote control A i a Enter 1 skip 7 The message Enjoy your watching is displayed When you have finished press the ENTER OK button Plug amp Play gt Even if the ENTER OK button is not pressed the Set the Clock Mode message will automatically disappear after several seconds Clock Mode Auto Move Genter M Skip Plug amp Play Set current date and time ma MOQ tbs D g lt gt Move Adjust 6 Enter M Skip Engis Continued Setting the Clock Automatically 8 Press the ENTER OK button Plug amp Play Press the A or Y button to select Off or On then the 7 E ENTER OK button Select the time zone in which you live The message Select the time zone in which you live is displayed Victoria 9 Press the A or Y button to highlight the time zone QueenSland for your local area and to move the highlight to the SaN appropriate time zone on the map of the United States Woes Press the ENTER OK button nN If clock is not automatically set see pages 35 36 to set E the clock ra 10 The message Enjoy your watching is displayed Te lesions When you have finished press the ENTER OK button Plug amp Play gt Even if the ENTER OK button is not pressed the message will automatically disappear after several Enjoy your watching seconds Viewing the Display The display identifies the current channel and the status of te
46. ct Option PilPlay gt The selected music files are played Repeat mode On Delete selected File SelectAll DeselectAll Safe Remove Flash Disk Device Zoom Select Option DlPlay Music function information icon Displayed at the top left of the screen Icon Current OSD Function Music One Repeat Music One When a music file is repeated When a music file is played once ejojn Music Play Pause When pressing the PLAY PAUSE button on the remote control while music is playing The music stops and the Play text appears at the top of the screen gt Press the WISELINK button on the remote control to turn on the WISELINK mode Repeating Music Play You can play music repeatedly 14 After switching the mode to WISELINK select a memory device that you have installed Refer to page 51 52 WISELINK CHLIST FAV CH REC REW STOP PLAY PAUSE FF 2 Pressthe A or V button to select Music then press the ENTER OK button Delete MP3 files and existing folders are displayed 3 Press the A or Y button to select a music then press the blue button Press the A or Y button to select Repeat mode then press the lt or gt button to select On To cancel Repeat mode select Off 4 To exit WISELINK mode press the EXIT button on the remote control gt Press the WISELINK button on the remote control to turn on the WISELINK mode Device Delete All SelectAll Infor
47. ctly Check that the batteries are drained Screen is black and power indicator light blinks steadily On your computer check Power Signal Cable Move the computer s mouse or press any key on the keyboard On your equipment check STB DVD etc Power Signal Cable The TV is using its power management system Press the Source button on the panel or remote control Turn the TV off and on The damaged picture appears in the corner of the screen If Just Scan is selected in some external devices the damaged picture may appear in the corner of the screen This symptom is caused by external devices not TV OOo OO SPHOOOO English 77 Specifications The descriptions and characteristics in this booklet are given for information purposes only and are subject to modification without notice Model Name PS50P91FD PS58P91FD PS63P71FD Screen Size Diagonal 50 inch 58inch 63 inch PC Resolution 1920 x 1080 60 Hz Sound Output 15W x2 Dimension WxHxD Body 1289x739x95mm 1465 x 838 x 100mm 1528 x 1001 x 88 mm With stand 1289 x 804x319mm 1465 x 905 x 345mm 1528 x 1087 x 423 mm Weight Body 45 kg 59 kg 70 0 kg With stand 49 kg 64 kg 87 0 kg Environmental Considerations Operating Temperature Operating Humidity Storage Temperature Storage Humidity 10 C to 40 C 50 F to 104 F 10 to 80 non condensing 20 C to 45 C 4 F to 113 F 5 to 95 non condensing
48. cture appears Refer to Storing Channels Automatically on page 16 or Storing Channels Manually on page 17 gt Ifthe television is initially powered on several basic customer settings proceed automatically Refer to Plug amp Play Feature on page 10 3 To switch the television off press the C Power button On Off on the front of the television or press the POWER button on the remote control 4 To switch the TV on press the C Power button On Off on the front of the TV or press the POWER button or number buttons on the remote control English 9 Plug amp Play Feature When the TV is initially powered on basic settings Plug amp Play proceed automatically Runs the Plug amp Play function when setting the TV up 1 Press the POWER button on the remote control for the first time or when resetting it Sets the The message Runs the Plug amp Play function when channels clocks as well as other functions setting the TV up for the first time or when resetting it Sets the channels the clocks as well as other functions is automatically displayed 2 The message Select Home Mode when installing this HEE TV at home is automatically displayed Select Home Mode when installing this TV at home 3 Press the lt or gt button to select Shop or Home then press the ENTER OK button gt The default selection is Home Shop gt gt We recommend setting the TV to Home mode for the lt gt Move Enter M Skip best pi
49. cture in your home environment gt Shop mode is only intended for use in retail environments Press Enter to start channel memory gt Ifthe unit is accidentally set to Shop mode and you want to return to Dynamic Home mode press the Volume button and then hold down the MENU button Genter D Return Plug amp Play for five seconds on the TV panel 4 The TV will begin memorizing all of the available Entert M Skip channels Plug amp Play After all the available channels are stored the Auto Rese program menu reappears p ea Digital Channel found 0 Press the ENTER OK button when channel memorization fo 3 is complete Digital Channels are added on the favourite channel list The Clock Mode menu is displayed gt To stop the search before it has finished press the ENTERIOK button with stop selected Enter M Skip 5 Press the ENTER OK button Plug amp Play Press the A or Y button to select Manual for setting the current time manually then press the ENTER OK button Auto Store is completed 7 5 3 channels are memorized The message Set current date and time is displayed Digital 1 Analog 2 gt Ifyou select Auto Select the time zone in which you live is displayed then go to step 8 6 Press the lt or gt button to move to Month Day Year EAT MUSH Hour Minute or am pm Set the date and time you want Plug amp Play bypressing the A or Y button then press the ENTER OK SACER button gt You
50. d gt If you have select ZOOM the Rotate function is deactivate Device Zoom Option TOOLS WISELINK CHLIST FAV CH REC gt Press the WISELINK button on the remote control to turn on the WISELINK mode REW STOP PLAVPAUSE FF The Rotating function information icon Displayed at the top left of the screen Icon Current OSD Function 270 Rotating 270 To rotate a photo by 270 degrees Rotating 180 To rotate a photo by 180 degrees Rotating 90 To rotate a photo by 90 degrees Rotating 0 To rotate a photo to its original state Continued English 58 Background Music On Off If you set Background Music On the background music will be played when viewing photos one by one or ina Slide Show 1 After switching the mode to WISELINK select a memory device that you have installed Refer to page 51 52 2 Press the ENTER OK button to select Photo JPEG files and existing folders are displayed 3 Press the A or V button to select a photo then press the ENTER OK button gt Pressing the button over a photo icon shows the currently selected photo in full screen 4 Press the TOOLS button Press the A or Y button to select Background Music then press the lt or gt button to select On or Off gt gt On When the background music is available if you select On the music is played back gt gt Off Background music is not played 5 To exit WISELINK mode press the EXIT button on
51. dio You will only hear sound from the Home Theatre s Front Left and Right speakers and the subwoofer If you want to hear 5 1 channel audio connect the DIGITAL AUDIO OUT OPTICAL jack on the DVD player or Cable Satellite Box ie Anynet Device 1 or 2 directly to the Amplifier or Home Theatre not the TV Please see the home theatre s user manual for more information gt You can connect an Anynet device using the HDMI 1 3 cable Some HDMI cables may not support Anynet functions gt gt Anynet works when the AV device supporting Anynet is in the Standby or On status gt Anynet supports up to 12 AV devices in total English 64 Setting Up Anynet The following settings help set the Anynet functions To use the Anynet Function Anynet HDMI CEC must be set to On 1 Press the MENU button to display the menu Melody Medium Press the A or Y button to select Setup then press the Screen Bum protection ENTER OK button A Gael 2 Press the A or V button to select Anynet HDMI CEC ee aO So Setup then press the ENTER OK button SW Upgrade 3 Press the ENTER OK button to select Anynet HDMI a aun ction fel Pon CEC Setup then press the ENTER OK button 4 Pressthe A or Y button to select On then press the ENTER OK button gt gt The Anynet function is enabled gt If you select Off Anynet is disabled gt When the Anynet HDMI CEC function is disabled all the Anynet related operations are deactiv
52. dity chemical substance and where it operates continually such as the airport the train station etc Failure to do so may cause a serious damage to your set Any functions related to Digital TV DVB will only work in countries or areas where DVB T MPEG2 digital terrestrial signals are broadcasted Please confirm with your local dealer if you can receive i DVB T signals Although this TV set follows the DVB T specification maintaining compatibility with i the future coming DVB T digital terrestrial broadcasts is not guaranteed Several functions may not be available in some countries 2007 Samsung Electronics Co Ltd All rights reserved English 2 Contents General Information User Instructions Tennisens Checking Parts Using the Stand Base Control Panel Connection Panel Viewing the Remote Control cece Switching Your Television On and Off 9 Plug amp Play Feature eee s0 Viewing the Display st Viewing the Menus eh Using the TOOLS Button 0 12 Viewing External Signal Sources 13 Editing Device Names eee 14 Using the DTV Feature Setting the Guide oe eeeeeeeteeeeeeenees 15 Setting the Default Guide eee 15 Checking the Digital Signal Strength Digital 16 Channel Control Storing Channels Automatically 00 0 0 16 Storing Channels Manually 17
53. e Colour DNle 1 Press the MENU button to display the menu 2 Press the ENTER OK button to select Picture 3 Select the required option by pressing the A or Y button then press the ENTER OK button Available options Digital NR Active Colour DNle 4 When you are satisfied with your setting press the ENTER OK button 5 Press the EXIT button to exit Digital NR Off Low Medium High Auto If the signal received by the television is weak you can activate this feature to reduce any static and ghosting that may appear on the screen Active Colour Off On Size 16 9 a Digital NR Auto i P c Active Colour On DNle On Picture Reset If you turn on this option the Colours of the sky and grass will be stronger and clearer for a more vivid on screen picture gt gt When you select Standard or Movie in Picture Mode the Active Colour automatically changes to Off and it is deactivated When the Picture Mode is set to Dynamic the Active Colour is activated regardless of the Picture Mode setting DNie Off Demo On This TV includes the DNle function so as to provide a high visual quality If you set DNle to on you can view the screen with the DNle feature activated If you set the DNle to Demo you can view the applied DNle and normal pictures on the screen for demonstration purposes Using this function you can view the difference in the visual quality gt DNle Digital Natural Image engine DNIe
54. e Sours 1 certain audio video settings RETURN INFOC Aryne Press the INFO button on the remote control c COLOR BUTT H English 11 Viewing the Menus 1 With the power on press the MENU button The main menu will appear at the bottom of the screen There are seven menu groups Picture Sound Channel Setup Input Guide and PIP Mode Dynamic 2 Pressthe A or Y button then press the ENTER OK Contrast 100 button to select an item you want in the menu Press the Brightness 145 A lt gt ENTER OK button to display change or use Sharpness 75 the selected items Colour 55 3 Press the EXIT button to exit Colour Tone Using the TOOLS Button The Tools button allows you to display frequently used Menu TOOLS and Connection items with a Single button press 1 Press the TOOLS button Picture Size 16 9 The TOOLS menu will appear Picture Mode f Dynamic 2 Pressthe A button to select a menu then press the Sound Mode ESC UT ENTER OK button Sleep Timer z off 3 Press the A lt gt ENTER OK buttons to display change Delete from Favourite or use the selected items Auto Store For a more detailed description of each function refer to the corresponding page Device List see page 63 Move Enter Picture Setting see page 27 Sound Setting see page 33 Sleep Timer see page 36 Delete Favourite Channel see page 20 Auto Store see page 16 English 12 Viewing Externa
55. e code is listed try the first one 5 Press the POWER button on the remote control Your STB should turn on if your remote is set up correctly If your STB does not turn on after set up repeat steps 2 3 and 4 but try one of the other codes listed for your brand of STB If no other codes are listed try each code 000 through 074 i Note on Using Remote Control Modes STB When your remote control is in STB mode the volume buttons still control your TV s volume Continued English 72 Remote Control Codes VCR Brand Code Brand Code SAMSUNG 000 001 002 003 004 005 077 078079 MITSUBISHI 019 034 041 046 ADMIRAL 020 MONTGOMERY WARD 020 AIWA 025 MTC 002 025 AKAI 004 027 032 MULTITECH 002 005 025 038 AUDIO DYNAMICS 007 026 NEC 007 008 018 026 037 062 064 BELL amp HOWELL 018 OPTIMUS 020 BROKSONIC 022 PANASONIC 021 056 071 072 CANDLE 002 003 006 008 015 055 PENTAX 019 041 075 CANON 021 056 PENTEX RESEARCH 008 CITIZEN 002 003 006 008 015 055 PHILCO 021 056 059 COLORTYME 007 PHILIPS 021 080 CRAIG 002 024 PIONEER 019 026 039 053 CURTIS MATHES 002 007 008 017 021 025 056 064066 PORTLAND 015 049 055 DAEWOO 003 010 011 012 013 014 015 016 PROSCAN 017 DB 007 026 QUARTZ 018 DIMENSIA 017 QUASAR 021 056 DYNATECH 025 RADIO SHACK 006 018 020 021 024 025 029 034 ELECTROHOME 034 REALISTIC 048 056
56. ed gt If you select No the deletion will be cancelled Do you want to delete the 2 files including 4 To exit WISELINK mode press the EXIT button on the File 1 jpg remote control gt You cannot remove the read only files from the selected ones i gt You cannot restore the removed pictures i WISELINK CH LIST FAV CH REC gt Press the WISELINK button on the remote control to turn on i the WISELINK mode i REW STOP PLAYPAUSE FF Using the Music MP3 List You can play back the MP3 files saved on a memory device in various ways 1 After switching the mode to WISELINK select a memory device that you have installed Refer to page 51 52 2 Press the A or V button to select Music then press the E an ENTER OK button J Tomas Feel So Good mp3 20 J Steve Love mp3 MP3 files and existing folders are displayed J Jane Holiday mp3 3 Press the A or V button to select a music to be played then press the ENTER OK button gt Pressing the ENTER OK button while a music file is highlighted immediately plays the music file gt Pressing the ENTER OK button while a folder is highlighted shows the music files in the folder gt To select a file on the next page press the REW or x FF button e gt 1 4 eal 53 00 04 10 gt Pressing the lt or gt button while playing a music file _ will let you play another music file in the same folder gt To play back the files repeatedly change the setting by referring to page
57. er three digits of the code even if the first digit is a 0 If more than one code is listed try the first one i 5 Press the POWER button on the remote control Your VCR should turn on if your remote is set up correctly If your VCR does not turn on after set up repeat steps 2 3 and 4 but try one of the other codes listed for your brand of VCR If no other codes are listed try each VCR code 000 through 080 i Note on Using Remote Control Modes VCR When your remote control is in VCR mode the volume buttons still control your TV s volume Setting Up the Remote to Operate Your Cable Box 1 Turn off your cable box 2 Press the CABLE button on your TV s remote control 3 Press the SET button on your TV s remote control 4 Using the number buttons on your remote control enter three digits of the cable box code listed on page 74 of this manual for your brand of cable box Make sure you enter three digits of the code even if the first digit is a 0 If more than one code is listed try the first one 5 Press the POWER button on the remote control Your cable box should turn on if your remote is set up correctly If your cable box does not turn on after set up repeat steps 2 3 and 4 but try one of the other codes listed for your brand of cable box If no other codes are listed try each code 000 through 046 i Note on Using Remote Control Modes Cable Box When your remote control is in CABLE mode
58. ess the A or V button to select Channel List then CT umen a press the ENTER OK button AutoStore 4 Press the lt button to select Added Channels Manual Store 5 Press the A or V button to select Programed then press Froti the ENTER OK button P Signal Strength You can view reservations CNA Y7HD Digital 7Digital 1 TDigital 2 YTDigital 3 c1 c2 3 C4 c5 Zoom Select Option 2007 2 3 3 3 15 am j No Program Name 4 15 am 7 No Program Name 2007 2 4 2 14 am 5 No Program Name 2007 2 5 2 15 am a No Program Name Zoom Select Option Information Modifying a viewing reservation 6 To select a reservation item to be modified press the A or Y button and then press the blue button 7 Press the ENTER OK button to select Change Info 3 G 8 Press the A V lt gt buttons to change a reservation Si linemen setting and then press the ENTER OK button 6 No Program Name The reservation modification is applied PEA yeas Cancelling a reservation 6 To select a reservation item to be cancelled press the A SS SIS SARS SOON SNS or Y button and then press the blue button 7 Press the A or V button to select Cancel schedules then press the ENTER OK button 8 Press the lt or gt button to select OK then press the ENTER OK button The viewing reservation has been cancelled 9 Press the EXIT button to exit Programed Menu Change Info Select to change a viewing reservation Cancel
59. ewing the TV during the day or button on the remote control H TEXT MIX MODE PIP when there is bright light in the room Choose Standard for general TV watching mode Choose Movie when viewing the movie English 26 Customizing the Picture Settings Your television has several setting options that allow you to control the picture quality 1 To select the desired picture effect follow the Changing the Picture Standard instructions number 1 to 3 on page 26 Press the A or button to select a particular item Press the ENTER OK button Press the lt or gt button to decrease or increase the value of a particular item Press the ENTER OK button Press the EXIT button to exit Contrast Adjusts the lightness and darkness between objects and the background Brightness Adjusts the brightness of the whole screen Sharpness Adjusts the outline of objects to either sharpen them or make them more dull Colour Adjusts the colours making them lighter or darker Tint Use this function to adjust the colour of objects making them more red or green for a more natural look when RF 60Hz AV 60Hz S Video 60Hz compone nt HDMI signals are input Colour Tone Cool2 Cool1 Normal Warm1 Warm2 gt gt When the picture mode is set to Dynamic or Standard Warm1 and Warm2 cannot be selected Picture Reset Reset All Reset Picture Mode Reset All All the picture values return to default settings Reset Picture
60. f Low Medium High Edge Enhancement On You can directly select the black level on the screen to adjust the screen depth lies a Dynamic Contrast Off Low Medium High You can adjust the screen contrast so that the optimal contrast is provided Gamma 3 3 You can adjust the middle brightness of pictures Press the lt or gt button until you reach the optimal setting Colour Space You can set the colour reproduction space for the input signal to Auto or Wide White Balance R Offset G Offset B Offset R Gain G Gain B Gain Reset You can adjust the colour temperature for more natural picture colours R Offset G Offset B Offset R Gain G Gain B Gain Changing the adjustment value will refresh the adjusted screen Select the required option by pressing the A or Y button then press the ENTER OK button Press the lt or gt button until you reach the optimal setting Reset The previously adjusted white balance will be reset to the factory defaults My Colour Control Pink Green Blue White Reset This setting can be adjusted to suit your personal preferences Select the Pink Green Blue or White by pressing the A or Y button then press the ENTER OK button Press the lt or gt button until you reach the optimal setting Reset The previously adjusted colours will be reset to the factory defaults Edge Enhancement Off On You can emphasize object boundaries English 28 Selecting the Picture Size You can select the picture size whic
61. function enables you to view and listen to photo JPEG and audio files MP3 saved ona USB Mass Storage Class MSC device 1 Press the POWER button on the remote control or front panel 2 Connect a USB device containing JPEG and or MP3 TV Side Panel files to the WISELINK jack USB jack on the side of the TV HDMLIN3 WISELINK E VIDEO gt Fa es Removing a USB Device DA 14 Press the MENU button to display the menu 2 Pressthe A or V button to select Guide then press the ENTER OK button 3 Press the ENTER OK button to select WISELINK k The photo or music files saved on the memory device are AES ii listed a 4 Press the blue button and press the A or Y button to Celt ease select Safe Remove and press the ENTER OK button The Now amp Next Guide Removing the device safe message appears and then the USB could be removed safe message appears Remove the USB device from the TV gt Ifyou enter the WISELINK mode with no USB device connected No external storage device found Check the connection status message will appear In this case insert the USB device exit the screen by Maj EoNEni ele pressing the WISELINK button on the remote control e zoons and enter the WISELINK screen again pj ea ane Photo and audio files must be named in English G Fie 4 ipg 20071112 If not the files can not be played Change the file names to English French or Spanish if necessary
62. h best corresponds to your viewing requirements 1 Press the MENU button to display the menu 2 Press the ENTER OK button to select Picture 3 Press the A or V button to select Size then press the ENTER OK button 4 Select the required option by pressing the A or Y button then press the ENTER OK button Available options 16 9 Zoom1 Zoom2 4 3 Just Scan 16 9 Sets the picture to 16 9 wide mode Zoom Magnifies the size of the picture on the screen Zoomz2 Expands the Zoom1 format picture 4 3 Sets the picture to 4 3 normal mode Just Scan Use this function to see the full image without cutting off the picture when HDMI 1080i 1080p 720p or Component 1080i 1080p 720p or DTV 1080i 1080p signals are input 5 Press the EXIT button to exit oe eee gt You can change the picture size simply by pressing the P SIZE button on the remote control gt 16 9 and 4 3 are available in all modes Zoom1 and Zoom2 are available in ATV DTV E 0 16 9 Zoom1 Zoom2 4 3 Colour Tone Detailed Settings Digital NR Active Colour DNle Picture Reset Just Scan Move Enter Component 480i 480p 576i 576p HDMI 480p 576p AV and S Video modes In Zoom1 Zoom2 modes you can move the picture on the screen by pressing the A or Y button Each adjusted setting will be stored separately according to its input mode English 29 eo D Return Digital NR Activ
63. hat enables you to control all connected Samsung AV devices with your Samsung TV s remote Connecting Anynet Devices The Anynet system can be used only with Samsung AV devices that have the Anynet feature To be sure your Samsung AV device has this feature check if there is an Anynet mark on it To directly connect to TV Connect the HDMI 1 HDMI E EA TE Anynet Device 1 Anynet Device 2 Anynet Device3 2 or HDMI 3 jack on the TV c oe 5 D J and the HDMI OUT jack of the f aaa corresponding Anynet device HomourT HDMI OUT using the HDMI cable HoMiouT G Ca TE HDMI 1 3 Cable f HDMI 1 3 Cable To connect to Home Theatre TV 1 Connect the HDMI 1 HDMI 2 or HDMI 3 jack on the TV and the HDMI OUT jack of the corresponding Anynet device using the HDMI cable ae eee 2 Connect the HDMI IN jack i of the home theatre and the HDMI OUT jack of the corresponding Anynet device using the HDMI cable Anynet Device 1 Anynet Device 2 HDMI OUT HDMI 1 3 Cable Optical Cable gt Connect the Optical cable between Digital Audio Out Optical on your TV and Digital Audio Input on the Home Theatre gt Connect only one Home Theatre gt When following the connection above the Optical jack only outputs 2 channel au
64. he menu 2 Press the A or Y button to select Channel then press the ENTER OK button 3 Press the A or button to select Channel List then press the ENTER OK button 4 Press the lt button to select Added Channels 5 Press the A or w button to select Favourite then press the ENTER OK button You can view all favourite channels 6 Press the A or W button to select Added Channels then press the ENTER OK Button 7 Press the A or button to select a channel as a favourite channel then press the blue button 8 Press the A or V button to select Add to Favourite then press the ENTER OK button The Y symbol will be displayed and the channel will be set as a favourite 9 To cancel your favourite channel selection press the blue button when a favourite channel is selected Press the A or V button to select Delete from Favourite then press the ENTER OK button The channel is deleted from Favourites and the v mark also disappears 10 Press the EXIT button to exit gt You can also Add or Delete a channel from Favourites in the All Channels menu in the same manner gt Only memorized channels can be set as favourite channels gt All favourite channels will be shown on Favourite menu gt You can select these options simply by pressing the CH LIST button on the remote control Easy Setting 1 Press the TOOLS button on the remote control 2 Press the A V button to select Add to Favourite or Delete from Favourite
65. hing the mode to WISELINK select a memory device that you have installed Refer to page 51 52 2 Press the ENTER OK button to select Photo WS feet _ane JPEG files and existing folders are displayed 1 eze 2007 12 3 Pressthe A or Y button to select a photo then press the Drm Be ENTER OK button gt Pressing the button over a photo icon shows the currently selected photo in full screen 4 Press the TOOLS button Press the A or Y button to select Zoom then press the ENTER OK button Each time the lt or gt button is pressed the photo size decreases or increases x1 gt x2 gt x4 x1 Restore the photo to its original size oa A x2 Zoom in to the photo x2 cure Mode Dynamic x4 Zoom in to the photo x4 TS Device Zoom Option TOOLS Start Slide Show Move Enter Continued English 56 5 To move the enlarged photo image up downl left right press the ENTER OK button then press the A lt P buttons gt Note that when the enlarged picture is smaller than the original screen size the location change function doesn t work 6 To exit WISELINK mode press the EXIT button on the remote control gt The enlarged file is not saved lt gt Move Enter fo0Ls Option imiseLiNa List gt Press the WISELINK button on the remote control to turn on a C7 UL E E the WISELINK mode i WISELINK CHLIST FAV CH REC REW STOP PLAY PAUSE FF i Zoom function information icon Displayed at
66. iles the screen to the right appears A z_break_away mp3 is read only file Delete it ENTERIOK button The music files are removed To exit WISELINK mode press the EXIT button on the remote HN anu Ewe REC control gt Press the WISELINK button on the remote control to turn on l REW STOP PLAYPAUSE FF i the WISELINK mode HALL Deleting Multiple Music Files 1 Inthe Music list press the A or Y button to select a music file to be deleted and press the yellow button mE gt The tick mark appears to the left of the selected i Repeat mode On music file 3 gt Repeat the above operation to select multiple music Bacal files sue 2 Press the blue button press the A or Y button to select Delete selected File and press the ENTER OK button Ts Zoom Select Option iPlay 3 Press the lt or gt button to select Yes and press the ENTER OK button Do you want to delete the 2 files including gt The selected music files will be deleted Tomas Feel So Good mp3 gt Ifyou select No the deletion will be cancelled 4 To exit WISELINK mode press the EXIT button on the remote control gt You cannot remove the read only files from the selected ones i wiselink CHLIST FAV CH REC gt You cannot restore the removed pictures f gt Press the WISELINK button on the remote control to turn on i REW STOP PLAY PAUSE FF the WISELINK mode Say ees a Pde re English 63 What is Anynet Anynet is an AV network system t
67. in PIP mode and turn it on again the PIP window will disappear gt You can view Analog TV broadcasts on the PIP screen sub picture when the main picture is from an external device connected to HDMI1 2 3 Component1 2 PC or AV1 2 S Video Main picture Sub picture Component 1 2 Analog TV broadcasts only HDMI 1 2 3 PC AV1 2 S Video gt You can select these options simply by pressing the PIP button 47 oneal ie on the remote control i B O gt Ifthe main picture is 6 0Hz except PC the PIP function cannot eg be used When you see DVD please choose 50Hz signal GUDE ea SILL ee i i I O MOO Changing the Size of the PIP Window 4 Pressthe A or Y button to select Size then press the lea ENTER OK button mong EE Press the A or button to select the desired size of the Size PIP window then press the ENTER OK button gt You may notice that the picture in the PIP window becomes slightly unnatural when you use the main picture to view a game or karaoke gt The Double Window and Double Wide cannot be use when the main picture is PC model Position Channel Continued English 31 Changing the Position of the PIP Window 5 Press the A or V button to select Position then press PIP the ENTER OK button B Press the A or button to select the desired PIP window x position then press the ENTER OK button Fosition gt In Double Window O0 and Double Wide CQ Channel modes
68. l Signal Sources You can switch between viewing signals from connected equipment such as a VCR DVD Set Top Box and the TV source broadcast or cable 1 2 3 4 gt You can select these options simply by pressing the SOURCE Press the MENU button to display the menu Press the A or Y button to select Input then press the ENTER OK button Press the ENTER OK button again to select Source List Press the A or Y button to select the signal source then press the ENTER OK button Available signal sources TV AV1 AV2 S Video Component1 Component2 PC HDMI1 HDMI2 DVI HDMI3 USB button on the remote control English 13 Edit Name a AV1 INA S Video Component1 Component2 PC Refresh Option POWER SOURCE J Editing Device Names You can give a name to the external source 14 Press the MENU button to display the menu Source List 2 Press the A or button to select Input then press the a ENTER OK button s EES 3 Press the A or Y button to select Edit Name then press D the ENTER OK button 4 Press the A or Y button to select the external source to be edited then press the ENTER OK button 5 Select the required device by pressing A or Y then press the ENTER OK button Available device names VCR DVD D VHS Cable STB HD STB Satellite STB PVR STB AV Receiver DVD Receiver Game Camcorder DVD Combo DVD HDD
69. l shut off and turn on automatically after completing the firmware upgrade Please check the firmware version after the upgrades are complete gt When software is upgraded video and audio settings you have made will return to their default factory settings We recommend you write down your settings so that you can easily reset them after the upgrade English 45 Over the Air Download 1 Press the MENU button to display the menu Burn Prot 2 Press the A or Y button to select Setup then press the net HDN ENTER OK button b SWUpgrade Over the Air Download 3 Press the A or V button to select SW Upgrade then eres USB Download press the ENTER OK button Fee 4 press the ENTER OK button to select the Over the Air 4 Download 5 Press the A or V button to select Software Information Manual Upgrade or Standby Mode Upgrade Press the ENTER OK button gt Software Information Press the ENTER OK button then the current software canara Usarede version appears Then you can upgrade the software as o the pictures gt Manual Upgrade ae ect rade On Press the ENTER OK button to search for new software K is i from the currently broadcasting channels The operations are same as you enter the software information Move Enter D Return gt Standby Mode Upgrade On Off When you turn off your TV software upgrade will be conducted automatically after 45 minutes During this upgrade the screen can be illuminatedslightly in case of R
70. lank screen being displayed DVI IN HDMI 2 AUDIO L R DVI audio outputs for external devices The external devices that support lower version HDMI mode may not implement sound ouput for theTV with the latest HDMI version HDMI 1 3 In this case connect to HDMI IN2 and DVI IN HDMI 2 R AUDIO L on the back panel of the TV Part of lower version HDMI cables may cause annoying flickers or no screen display in this case use the cable that supports the latest HDMI version HDMI 1 3 English 7 0000 668 OO 68 6 68 866 Viewing the Remote Control Power Channel Volume STOP and PLAY PAUSE buttons The performance of the remote control may be affected by bright light POWER button turns the TV on and off Number buttons for direct channel access One Two Three digit channel selection Channel contro button This function enables you to view and play photo JPEG and audio files MP3 from an external device Volume increase Volume decrease Temporary sound switch off Displays the main on screen menu Returns to the previous menu Picture size selection Electronic Program Guide EPG display Sound mode selection Remote control setup Selects a target device to be controlled by the Samsung remote control TV DVD STB CABLE VCR Press to backlight the VOL CH and the active source button TV DVD CABLE STB VCR on the remote Available source selection Previous ch
71. manufacturers gt The Anynet functions do not work with other manufacturers products gt The lt lt gt gt operations may differ depending on the device Recording You can make a recording of a TV program using a recorder TOOLS 1 eee button 2 Pressthe A or V button to select to Record Immediately and Device List ress the ENTER OK button RBI Recording DVD ecording begins 3 When there are more than one recording device zm ne aa When multiple recording devices are connected the recording a tat devices are listed Press the A or Y button to select to a Hee oo recording device and press the ENTER OK button Recording Picture Mode Dynamic begins Sound Mode 2 Standard When the recording device is not displayed Sleep Timer off Select Device List and press the red button to search devices 4Move Enter Press the EXIT button to exit gt You can record instantly using the REC button of the TV remote control gt The current TV program is recorded in the Watching TV status If you are watching video from another device the video from the device is recorded gt gt Before recording check whether the antenna jack is properly connected to the recording device For the antenna connection to the recording device refer to its user manual English 67 Listening through a Home theatre You can listen to sound through a receiver home theatre instead of the TV s speakers 1 Press the Anynet button
72. mation Safe Remove Zoom Select Option P liPlay ieee UTTE WISELINK CHLIST FAV CH REC REW STOP PLAY PAUSE FF PEN ae EAN COR EO English 62 Continued Deleting the Music files You can delete music MP3 files saved on the USB storage device 1 After switching the mode to WISELINK select a memory device that you have installed Refer to page 51 52 2 Press the A or Y button to select Music then press the ED z ENTER OK button 4 Repeat mode On MP3 files and existing folders are displayed e Holiday mp3 3 Press the A or Y button to select a music file to be ae deleted and then press the blue button Safe Remove 4 Press the A or Y button to select Delete or Delete All and then press the ENTER OK button USB Device Zoom Select Option PIPlay gt Ifyou select Delete only the selected music will be deleted gt If you select Delete All all music files in the selected folder are deleted 5 Press the lt or gt button to select Yes and press the ENTER OK button gt The music will be deleted gt Ifyou select No the deletion will be cancelled gt You cannot remove the following files Read only files gt While removing any files don t remove the USB memory device gt You cannot restore a deleted music file Removing read only files Press the lt or button to select Yes then press the gt lf you select No the removing operation is cancelled When removing read only f
73. n ale Always store the TV Bas o upright Troubleshooting Before contacting the Samsung after sales service perform the following simple checks If you cannot solve the problem using the instructions below note the model and serial number of the television and contact your local dealer No sound or picture Check that the mains lead has been connected to a wall socket Check that you have pressed the C Power button On Off on the front panel or press the POWER button on the remote control Check the picture contrast and brightness settings Check the volume Check if Internal Mute is set to ON Normal picture but no sound Check the volume Check whether the volume MUTE button on the remote control has been pressed No picture or black and white picture Adjust the colour settings Check that the broadcast system selected is correct Sound and picture interference Try to identify the electrical appliance that is affecting the television then move it further away Plug the television into a different main socket Blurred or snowy picture distorted sound Check the direction location and connections of your aerial This interference often occurs due to the use of an indoor aerial Remote control malfunctions Replace the remote control batteries Clean the upper edge of the remote control transmission window Check that the and ends of the batteries are inserted corre
74. ns gt Do not use screws that do not comply with the VESA standard screw specifications Do not use fasten the screws too strongly this may damage the product or cause the product to fall leading to personal injury Samsung is not liable for these kinds of accidents gt Samsung is not liable for product damage or personal injury when a non VESA or non specified wall mount is used or the consumer fails to follow the product installation instructions gt Our 57 and 63 models do not comply with VESA Specifications Therefore you should use our dedicated wall mount kit for this model gt Do not exceed 15 degrees tilt when mounting this TV A Do not install your Wall Mount Kit while your TV is turned on It may result in personal injury due to electric shock English 76 How to assemble the Stand Base depending on the model Using the screws for securing the stand base and the monitor firmly attach In case of installing your the monitor to the stand base TV on the wall close the The exterior of the set may be different from the picture i cover on the stand base PS50P91FD PS58P91FD PS63P71FD Warning i connection part using two Firmly secure the stand to w taing the TV before moving it as the stand may fall and could Se gt Two or more people should carry the TV Never lay the TV onthe Jo i floor because of possible cause serious injury x i T Al damage tothe scree
75. nter D Return Austraila lt Move Enter Return Screen Burn Protection 14 Press the MENU button to display the menu Blue Screen Press the A or Y button to select Setup then press the Wet ENTERIOK button ie a ae 3 Press the A or W button to select Screen Burn Aon A Protection then press the ENTER OK button x Anynet HDMI CEC Setup 4 Press the ENTER OK button to select the Pixel Shift then SW Upgrade press the ENTER OK button again Funetaniky oi 5 Press the A or Y button to select On for making the screen move per regular hour and preventing the residual image 6 Press the ENTER OK button Pixel Shift Using this function you can minutely move pixels on the PDP in horizontal or vertical direction to Screen Burn Protection minimize after image on the screen Pixel Shift 7 Select the required option Horizontal Dot Vertical Line ina or Time by Press the A or Wbutton Press the ENTER OK button 8 Press the A or V button until you reach the optimal setting Press the ENTER OK button gt Optimum condition for pixel shift Scrolling Side Gray Horizontal Dot 2 Vertical Line 4 Move Enter D Return Time 4 Pixel Shift 9 Press the EXIT button to exit Pixel Shift Horizontal Dot gt lf screen burn has occurred you can select a white screen or signal pattern rolling screen to help remove screen burn artifacts Vertical Line Time All White This function helps remo
76. occur when the product contracts or expands due to a change of surrounding environment such as temperature or humidity This is normal and not a defect of the unit Cell Defects The PDP uses a panel consisting of 1 230 000 SD level to 3 150 000 HD level pixels which require sophisticated technology to produce However there may be few bright or dark pixels on the screen These pixels will have no impact on the performance of the product Avoid operating the TV at temperatures below 5 C 41 F Astill image displayed too long may cause permanent damage to the PDP Panel Watching the PDP TV in 4 3 format for a long period of time may leave traces of borders displayed on the left right and centre of the screen caused by the difference of light emission on the screen Playing a DVD or a game console may cause similar effect to the screen Damages caused by the above effect are not covered by the Warranty Afterimage on the Screen Displaying still images from Video games and PC for longer than a certain period of time may produce partial afterimages To prevent this effect reduce the brightness and contrast when displaying still images Warranty Warranty does not cover any damage caused by image retention Burn in is not covered by the warranty Installation Be sure to contact an authorized service centre when installing your set in a location with heavy dust high or low temperatures high humi
77. og channel the Child Lock ea MOVE ToC function can be selected Child Lock Child Lock Child Lock Channel 4 NWA Lock Unlocked Move G Enter D Return Child Lock Child Lock On Channel Unlocked Locked Lock Move G Enter OD Return English 38 Setting the Subtitle 1 Press the MENU button to display the menu 2 Press the A or Y button to select Setup then press the ENTER OK button 3 Press the A or V button to select Subtitle then press the ENTER OK button 4 Select On by pressing the ENTER OK button 5 Press the A or V button to select required menu Subtitle Mode Subtitle Language then press the ENTER OK button The options of the selected menu are displayed 6 Press the EXIT button to exit gt The Subtitle Language availability depends on your country if the signal does not include subtitle language the function is not active English 39 Timer 3 Child Lock Medium Off Menu Transparency Energy Saving HDMI Black Level Normal Subtitle Subtitle Move Enter Subtitle Subtitle Subtitle Mode Subtitle Language Hard of Hearing Move Enter Subtitle Subtitle Subtitle Mode Subtitle Language Move Enter Inactivated D Return Normal D Return D Return Using the Game Mode When connecting to a game console such as Child Lock PlayStation or Xbox you can enjoy a more realistic Sub
78. on to select Manual Store then press the ENTER OK button 4 Select the required option by pressing the A or Y button then press the ENTER OK button Channel List gt On digital mode you can choose Digital Channel on Auto Store analog mode you can choose Digital Channel and Naroal Store Analog Channel 5 When you are satisfied with your setting press the Eine Tut ENTER OK button agp ciazal strength 6 Press the EXIT button to exit qe Programme Programme number to be assigned to a channel Press the A or Y button until you find the correct number gt You can also select the channel number directly by pressing the numeric buttons 0 9 ierivel Sita Colour System Auto PAL Press the A or Y button to select the required colour Channel Frequency Bandwidin standard i Sound System DK I BG i Press the A or Y button to select the required sound standard Channel When you know the number of the channel to Adjust lt gt Move Enter Return be stored Press the A or Y button to select C Air channel or S Manualstore Cable channel Programme Colour System Sound System Press the button then press the A or Y button to select the required number gt You can also select the channel number directly by Channel Search pressing the numeric buttons 0 9 gt If there is abnormal sound or no sound reselect the sound standard required Adjust lt Move Enter D Return Search When you do not kn
79. ound Select Main Sub When the PIP feature is activated you can listen to the sound of the sub PIP picture Main Used to listen to the sound of the main picture Sub Used to listen to the sound of the sub picture Digital Format The Digital Format appears according to the broadcasting signal gt While viewing a Digital channel the Digital Format function can be selected Sound Reset Reset All Reset Sound Mode Reset All All the picture values return to default settings Reset Sound Mode Current sound values return to default settings TRADEMARK amp LABEL LICENSE NOTICE DO posy Manufactured under license from Dolby Laboratories DIGITAL Dolby and the double D symbol are trademarks of Dolby Laboratories English 33 Selecting the Sound Mode depending on the model The DUAL I II button displays controls the processing and output of the audio signal When power is switched on the i DUAL STILL SUBTITLE mode is automatically preset to either DUAL I or Stereo Cc depending on the current transmission H OSET YH ORESET Type of broadcast On screen indication Ne ley 2 46 nical Regular broadcast Standard audio Mono Normal use Regular NICAM Mono NICAM Mono Normal NICAM NICAM pane Mono Stereo CAMS stereo Normal NICAM NICAM Mono NICAM DURES dual 4 gt dual 2 Normal Regular broadcast a Standard audio Mono Normal use Stereo Biling
80. ow the channel numbers Press the A or Y button to start the search The tuner scans the frequency range until the first channel or the channel that you selected is received on the screen Store When you store the channel and associated programme number Set to OK by pressing the ENTER OK button Channel mode P Programme mode When completing tuning the broadcasting stations in your area have been assigned to position numbers from P00 to P99 You can select a channel by entering the position number in this mode C Air channel mode You can select a channel by entering the assigned number to each air broadcasting station in this mode S Cable channel mode You can select a channel by entering the assigned number for each cable channel in this mode English 17 Managing Channels Using this menu you can Add Delete or set Favourite channels and use the program guide for digital broadcasts Viewing All Channels e Show all currently available channels TTA To use the Channel List function first run Auto Program S 1 Press the MENU button to display the menu BW Fine Tune 2 Press the A or Y button to select Channel then press the Signal Strength ENTER OK button LNA 3 Press the A or V button to select Channel List then press the ENTER OK button 4 Press the lt button to select Added Channels 5 Press the A or VW button to select All Channels then press the ENTER OK button Shows all currently
81. rections English 4 Control Panel i Front or Side Panel PS50P91FD PS58P91FD S 7 PS63P71FD SAMSUNG 6 gt The product colour and shape may vary depending on the model SOURCE Displays a menu of all of the available input sources TV AV1 AV2 S Video Componentt Component2 PC HDMI1 HDMI2 DVI and HDMI3 USB gt Inthe on screen menu use this button as you would use the ENTER OK button on the remote control PS50P91FD MENU Press to see the on screen menu of your TV s features VOL Press to increase or decrease the volume In the on screen menu use the VOL buttons as you use the lt and gt buttons on the remote control 4 6 oO English 5 ACHY Press to change channels In the on screen menu use the N CH W buttons as you use the A and Y buttons on the remote control ENTER Press to confirm a selection PS63P71FD Power button Press to turn the TV on and off Power Indicator Power Off Blue Red PS50P91FD PS58P91FD Power On Off Remote Control Sensor Aim the remote control towards this spot on the TV Speaker Connection Panel Side Panel I WISELINK E am 0 Og po o gt o E han o Q a po
82. rnal devices English 40 Setting up the Parental Lock This feature allows you to prevent unauthorized users Subtitle such as children from watching unsuitable programmes by a 4 digit PIN Personal Identification Number code that is defined by the user The on screen menu will instruct 6 Gael you to assign a PIN code you can change it later if e MenuTransparency Medium necessary Energy Saving Off 1 Press the MENU button to display the menu PE 2 Pressthe A or Y button to select Setup then press the ENTER OK button MIB Normal 3 Press the A or Y button to select Parental Lock then Film Mode Oi press the ENTER OK button Wall Mount Adjustment 4 Press the number buttons to enter your current 4 digit PIN gt The default PIN for a new TV set is 0 0 0 0 5 The Parental Lock screen will appear Press the A or Y button to select Change PIN then press the ENTER OK button Enter PIN 6 The Change PIN screen will appear Press the number buttons to enter your new 4 digit PIN Re enter the same 4 digits The message PIN is changed sucessfully is displayed then your PIN has been memorized 7 Press the EXIT button to exit gt Ifyou forget the PIN press the remote control N DR buttons in the following sequence which resets the pin to 0 0 0 0 Power Off gt Mute gt 8 gt 2 gt 4 gt Power On Parental Rating Change PIN Parental Lock Parental Lock Move G Enter D Return Change PIN
83. rounding lighting conditions Off Switches off the Energy Saving mode Low Operates in standard mode regardless of the surrounding illumination Medium Enters Medium power saving mode regardless of the surrounding illumination High Enters maximum power saving mode regardless of the surrounding illumination HDMI Black Level Normal Low Use this function to adjust the Black Level of the picture while in HDMI mode Normal The screen gets brighter Low The screen gets darker gt This function is active only when the externel input connects to HDMI RGB signals Film Mode On Off You can automatically sense and process film signals and adjust the picture for optimum quality gt Film Mode is available in TV AV S Video and Component modes Light Effect PS50P91FD PS58P91FD Off in Standby In Watching TV Always You can turn on off the blue LED on the front of TV according to the situation Use it for saving power or when the LED dazzles your eyes Off The blue LED is always off In Standby The blue LED lights while in Standby mode and it turns off when your TV is turned on In Watching TV The blue LED lights when watching TV and it turns off when your TV is turned off Always The blue LED always lights gt Set the Light Effect to Off to reduce the power consumption Blue Screen On Off If no signal is being received or the signal is very weak a blue screen automatically replaces the noisy picture
84. s for your TV s firmware in the future There are two methods to upgrade the software Please contact the Samsung call center at 1 800 SAMSUNG to receive information about downloading upgrades and using the USB device and Over the Air Download Upgrades will be possible by connecting a USB drive to the USB port located on the back of your TV and using Over the Air Download Using a USB TV Side Panel A a i 7 n Screen Burn Protection 1 Insert a USB drive containing the firmware upgrade into Anynet HDMI CEC Setup the USB Upgrade Port on the side of the TV 6 ee eas E Function Help On 2 Press the MENU button to display the menu Software Upgrade 3 Press the A or V button to select Setup then press the ENTER OK button Scanning for USB 4 Press the A or Y button to select SW Upgrade then lmay take up to 30 seconds press the ENTER OK button and select USB Download The message Scanning for USB It may take up to 30 seconds is displayed 5 If the firmware on the USB is properly recognized the SorwareUporade message Upgrade version xxxx to version xxxx The Upgrade version XXXX to version XXXX The system would be reset after upgrade is displayed system would be reset after upgrade Press the lt or gt button to select OK then press the ENTER OK button The upgrade starts Cancel Please be careful not to disconnect the power or remove the USB drive while upgrades are being applied The TV wil
85. schedules Select to cancel a viewing reservation Information Select to view a viewing reservation iT NRT NT NT TT gt You can select these options simply by pressing the CH LIST Wisin GALCER EACH REC button on the remote control REW STO PAUSE FF Continued English 22 Labeling Channels Analog Channels can labeled so that their call letters appear whenever the channel is selected 1 2 3 7 8 Press the MENU button to display the menu Press the A or Y button to select Channel then press the ENTER OK button Press the A or Y button to select Channel List then press the ENTER OK button Press the A or Y button to select the channel to be assigned a new name then press the blue button Press the A or Y button to select Channel Name Edit then press the ENTER OK button Press the A lt P button to select a letter then press the ENTER OK button Numeric buttons You can enter numbers Red button You can switch between English and Characters Green button You can delete an already entered character Yellow button You can enter a blank space Blue button Press this button to finish renaming a channel When you have finished press the blue button to assign the new name Press the EXIT button to exit gt The names of digital broadcasting channels are automatically assigned and thus cannot be assigned by users English 23 Auto Store Manual Store
86. situation that the TV is Fine Tune used in weak signal signal Strength LNA amplifies the TV signal in the weak signal area a n low noise preamplifier boosts the incoming signal EE 7 14 Press the MENU button to display the menu 2 Press the A or V button to select Channel then press the ENTER OK button 3 Press the A or V button to select LNA then press the ENTER OK button 4 Select Off or On by pressing the A or Y button then press the ENTER OK button 5 Press the EXIT button to exit gt gt Depending on areas factory mode of LNA will be Fine Tune set up as On or Off g Signal Strength LNA English 25 Changing the Picture Standard You can select the type of picture which best corresponds to your viewing requirements 14 Press the MENU button to display the menu a IMa 2 Press the ENTER OK button to select Picture nr a 3 Press the ENTER OK button again to select Mode O Contrast 100 4 Select the required mode by pressing the A or Y button p craninsss then press the ENTER OK button Sharpness Available modes Dynamic Standard Movie AA gt gt The settings values may vary depending on the input pues source ex RF Video Component PC or HDMI S cour tone 5 Press the EXIT button to exit S Sp Standard Movie 75 Colour Tint G R Colour Tone Cool1 etailed Settings gt You can select these options simply by pressing the PMODE i Toler i i gt gt Choose Dynamic for vi
87. tart Slide i eee Show Delete Delete All Select All Information Safe Safe Remove Remove Press the A or V button to select Start Slide Show FlashDisk Device Zoom Select Option PI Side Show then press the ENTER OK button gt Slide show displays all JPEG files in the selected folder at a pre set speed gt During the slide show files are displayed in order from the currently shown file gt MP3 files can be automatically played during the slide show if the Background Music is set to On To enable this function MP3 files and other photo files must be located in the same folder on the memory device gt Press the PLAY PAUSE button when a photo icon is selected to start a Slide Show Continued English 55 4 Press the TOOLS button during slide show to set the option 5 To exit WISELINK mode press the EXIT button on the remote control 1d Music Setting Picture Mode Dynamic Sound Mode Standard Information Move Enter gt Press the WISELINK button on the remote control to turnon i TOS ie the WISELINK mode WISELINK CHLIST FAV CH REC REW STOP PLAYIPAUSE FF i Slide Show Speed OOLS Select to control the slide show speed Start Slide Show Each time the lt or gt button is pressed the speed changes repeatedly 7 Fast Slow Normal Background Music on Background Music Setting Delete Picture Mode Dynamic Soun Standard Move Adjust G Enter Zooming In 1 After switc
88. the remote control gt Press the WISELINK button on the remote control to turn on the WISELINK mode Background Music Setting 1 After switching the mode to WISELINK select a memory device that you have installed Refer to page 51 52 2 Press the ENTER OK button to select Photo JPEG files and existing folders are displayed 3 Press the A or V button to select a photo then press the ENTER OK button gt Pressing the button over a photo icon shows the currently selected photo in full screen 4 Press the TOOLS button Press the A or V button to select Background Music Setting then press the ENTER OK button The music MP3 files are listed 5 Press the A or V button to select a particular music file and press the yellow button gt The lt gt mark appears to the left of the selected music MP3 gt Repeat the above operation to select multiple music files 6 Press the ENTER OK button to save the current selections 7 To exit WISELINK mode press the EXIT button on the remote control gt Ifyou turn Off the Background Music even if the Background Music Settings have been set up the background music will not be played English 59 2 3 mefoldert amp H Fiet 1 File 2jpg File 3jpg 01 File 4jpg Flash Disk Device Zoom Select WISELINK CH LIST FAV CH REW STOP PLAY PAUSE FF iO File 1 jpg iG File 2jpg T m folder 4 i File 3jpg 1 File 4jpg Flash Disk Device Zoom Select 20
89. the remote control photos in the folder will be gt You cannot remove the following files PTP connected digital camera picture files Read only files gt While removing files don t remove the USB memory device gt You cannot recover a deleted photo file Removing read only files When removing any read only files the screen to the right appears Press the lt or button to select Yes then press the ENTER OK button gt If you select No the removing operation is cancelled gt Press the WISELINK button on the remote control to turn on the WISELINK mode English 60 T tm Folder 1 p Omet 1 File 2jpg 0 File 3 jpg e File 4jpg Option Ba Folder 2 File 1 jpg Device Zoom Select PLAY PAUSE FF 2007 1 2 2007 1 2 Start Slide Show Delete Delete All SelectAll Information Safe Remove Option Pil Slide Show Continued Deleting Multiple Photos 1 Inthe Photo list press the A or Y button to select a photo to be deleted and press the yellow button Ba Foider 1 2007 1 2 gt The lt gt mark appears to the left of the selected re photo i a gt Repeat the above operation to select multiple photos ene 2 Press the blue button press the A or Y button to select Delete selected File and press the ENTER OK button 3 Press the lt or gt button to select Yes and press the e Zoom Select Option PllSlide Show ENTER OK button gt The selected photos are delet
90. the top left of the screen Icon Current OSD Function ea Zoom x 1 Restore a photo to its original size zo Zoom x 2 Zoom in to a photo x2 Pixs Zoom x 4 Zoom in to a photo x4 a Pan Up Pan up to view the upper part of a zoomed in photo lv Pan Down Pan down to view the lower part of a zoomed in photo KI Pan Left Pan left to view the left side of a zoomed in photo OG Pan Right Pan right to view the right side of a zoomed in photo Continued English 57 Rotating 1 After switching the mode to WISELINK select a memory device that you have installed Refer to page 51 52 2 Press the ENTER OK button to select Photo ee JPEG files and existing folders are displayed aga ee 3 Press the A or V button to select a photo then press the 1D Fie 3jpg 20071112 ENTERIOK button aca aie gt Pressing the button over a photo icon shows the currently selected photo in full screen 4 Press the TOOLS button Press the A or Y button to select Rotate then press the ENTER OK button Press the lt or gt button to rotate the photo by the required amount ea gt gt Whenever you press the lt button it rotates by 270 180 90 and 0 gt gt Whenever you press the button it rotates by 90 180 270 and 0 gt Rotating directly from 90 degrees to 270 degrees is not allowed 5 To exit WISELINK mode press the EXIT button on the remote control gt The rotated file is not save
91. the volume buttons still control your TV s volume Continued English 71 i Setting Up the Remote to Operate Your DVD 1 Turn off your DVD 2 Press the DVD button on your TV s remote control 3 Press the SET button on your TV s remote control 4 Using the number buttons on your remote control enter three digits of the DVD code listed on page 75 of this manual for your brand of DVD Make sure you enter three digits of the code even if the first i digit is a 0 If more than one code is listed try the first one 5 Press the POWER button on the remote control H Your DVD should turn on if your remote is set up correctly If your DVD does not turn on after set up repeat steps 2 3 and 4 but try one of the other codes listed for your brand of DVD If no other codes are listed try each code 000 through 141 Note on Using Remote Control Modes DVD When your remote control is in DVD mode the volume buttons still control your TV s volume i Setting Up the Remote to Operate Your Set Top Box 1 Turn off your STB 2 Press the STB button on your TV s remote control i 3 Press the SET button on your TV s remote control 4 Using the number buttons on your remote control enter three digits of the STB code listed on page 74 of this manual for your brand of STB Make sure you enter three digits of the code even if the first l digit is a 0 If more than on
92. then press the ENTER OK button The current channel is added to or deleted from Favourites gt To select the favourite channels you have set up press the FAV CH button on the remote control English 20 A Auto Store Manual Store Fine Tune Signal Strength LNA 1 THD Digital wal 7Digital 1 3 Y 7Digital 2 4 Y 7Digital 3 Avo c ATVI c2 ATv2 c3 ATV3 ATV4 c5 Zoom Select Option 7HD Digital Y7Digitai2 Delete from Favourite 7Digitai3 Timer Viewi Option O PARN Picture Size Picture Mode 3 Dynamic Sound Mode 5 Standard Sleep Timer g Off Delete from Favourite Auto Store Move Enter HO OTN AZT WISELINK CHLIST FAVCH REC REW STOP AS fii Continued Reserving a Program Time Viewing If you reserve a program you want to watch the channel is automatically switched to the reserved channel in the Channel List even when you are watching another channel To reserve a program set the current time first See pages 35 36 Reserved channels can only be set if they are in the Channel List See page 18 14 Press the MENU button to display the menu 2 Press the A or V button to select Channel then press the ENTER OK button 3 Press the A or V button to select Channel List then press the ENTER OK button 4 Press the A or Y button to select a channel then press the Blue Options button 5 Press the A or V button to select Timer Viewing then press the ENTER
93. title gaming experience by selecting game menu 1 Press the MENU button to display the menu 2 Press the A or Y button to select Setup then press the ck ENTER OK button Menu Transparency Medium 3 Press the A or button to select Game Mode then Energy Saving Off press the ENTER OK button k Pc 4 Select On by pressing the A or V button then press the Home theatre PC Off ENTER OK button HDMI Black Leve Normal 5 Press the EXIT button to exit iabttese gt Restrictions on Game Mode Caution To disconnect the game console and connect Child Lock another external device set Game Mode to Off s subtitle in the Setup menu If you display the TV menu in Game Mode the Celmelbtests screen shakes slightly Parental Lock The mark appears on the screen which Menu T cy Medium means that Game Mode is On with the selected e off source gt If Game Mode is On r off Picture Mode is automatically changed to V eve Normal Standard and users cannot change the mode off Sound Mode is automatically changed to Custom and user can not chang the mode Adjust the sound using the equalizer The Reset in the Sound menu is activated Reset function initializes the Equalizer settings to the factory default setting The Channel menu is deactivated gt Game Mode is not available in TV mode gt Ifthe picture is poor when external device is connected to TV check if Game Mode is On Set Game Mode to Off and connect exte
94. trol Anynet doesn t work at a certain condition Searching channels operating WISELINK When connecting or removing the HDMI cable please make sure to search devices again or restart your TV Check if the Anynet Function of Anynet device is set on Check if the Anynet device is properly connected to the TV and check if the Anynet HDMI CEC is set to On in the Anynet Setup menu m Press the TV button on the TV remote control to switch to TV Then press the Anynet button to show the Anynet menu and select a menu you want want to exit Anynet m Select View TV in Anynet menu m Press the SOURCE button on the TV remote control and select a device other than Anynet devices m Press any of CH CH LIST PRE CH and FAV CH to change to the TV mode Note that the channel button operates only when an Anynet device with a built in tuner is not connected The Connecting to Anynet m You cannot use the remote control when you are configuring Anynet device message appears or switching to a view mode on the screen m Use the remote control when the Anynet setting or switching to view mode is complete ae device does You cannot use the play function when Plug amp Play is in progress The connected device is Check whether or not the device supports Anynet functions not displayed m Check whether or not the HDMI cable is properly connected m Check whether lt Anynet HDMI CEC Setup gt is set to lt On gt in the An
95. ual or DUAL I II Dual cond paal Il ono Stereo Stereo Forced mono gt Ifthe receiving conditions deteriorate listening will be easier if the mode is set to Mono Ifthe stereo signal is weak and automatic switching occurs switch to Mono When receiving a mono sound in the AV mode connect to the AUDIO L input connector on the panel front or side If the mono sound comes out only from the left speaker press the DUAL I II button English 34 Setting the Time Setting the clock is necessary in order to use the various timer features of the TV Also you can check the time while watching the TV Just press the INFO button Option 1 Setting the Clock Automatically The Clock can be set automatically if you are receiving a digital signal 1 Press the MENU button to display the menu 2 Press the A or V button to select Setup then press the ENTER OK button 3 Press the A or V button to select Clock then press the ENTER OK button 4 Press the ENTER OK button to select Clock Mode 5 Press the A or Y button to select Auto then press the ENTER OK button 6 Press the A or V button to select Time Zone then press the ENTER OK button Press the A or Y button to highlight the time zone for your local area and to move the highlight to the appropriate time zone on the map of the United States then press the ENTER OK button 7 Press the EXIT button to exit Option 2 Setting the
96. uide NBC TODAY SUNRISE Setting the Default Guide You can preset the default guide style 1 Press the MENU button to display the menu Full Guide 2 Press the A or Wbutton to select Guide Press the NowaNext Guide ENTER OK button SUT j 3 Press the A or button to select Default Guide then emi i press the ENTER OK button Palee 4 Select Now Next or Full Guide using the A or Y button and press the ENTER OK button 5 Press the EXIT button to exit gt You can select these options by simply pressing the GUIDE button on the remote control GUIDE STILL SUBTITLE y BOO OSET ORESET English 15 Checking the Digital Signal Strength Digital Unlike analog channels which can vary in reception quality from snowy to clear digital HDTV channels have either perfect reception quality or you will not receive them at all So unlike analog channels you cannot fine tune a digital channel You can however adjust your antenna to improve the reception of available digital channels 14 Press the MENU button to display the menu 2 Press the A or Y button to select Channel then press the ENTERI OK button 3 Press the A or V button to select Signal Strength then press the ENTER OK button 4 Ifthe signal strength meter indicates that the signal is Signal Strength weak physically adjust your antenna to increase the T signal strength af Continue to adjust the antenna until
97. ure Mode 3 Dynamic gt Only when you set Anynet HDMI CEC to On in the Setup Sound Mode s Sai menu the Device List menu appears toa titer off gt Switching to the selected devices may take up to 2 minutes S You cannot cancel the operation during the switching Z Move MeiEnter operation gt The time required to scan for devices is determined by the number of connected devices gt When the device scan is complete the number of devices E ovo found is not displayed gt Although the TV automatically scans devices when it is turned on using the POWER button devices connected when the TV is already on are not displayed in the device list Therefore press the red button to re scan devices if necessary gt If you have selected an external device by pressing the SOURCE button you cannot use the Anynet function Make sure to switch to an external Anynet device by using the TAT ENO Rena Anynet button Anynet Menu The Anynet menu changes depending on the type and status of the Anynet devices connected to the TV Anynet Menu Description View TV Switches from Anynet to TV broadcast mode Device List Displays the Anynet device list Shows the menu of the connected device Menu on Device Example When a DVD Recorder is connected the DVD Recorder s title menu appears Shows the play control menu of the connected device Device Operation Example When a DVD Recorder is connected the play control menu of
98. ve after images on the screen by changing the colour of pixels to white Use this function when there are remaining after images or symbols on the screen especially when you displayed a still image on the screen for a long time Scrolling This function helps remove after images on the screen by moving all the pixels on the PDP according to a pattern Use this function when there are remaining after images or symbols on the screen especially when you displayed a still image on the screen for a long time Side Gray When you watch TV with the screen ratio of 4 3 the screen is prevented from any damage by adjusting the white balance on both extreme left and right sides Dark When you set the screen ratio to 4 3 it darkens the left and right sides Light When you set the screen ratio to 4 3 it brightens the left and right sides Move Enter D Return English 43 Wall mount adjustment Sold separately pssopo1rpipsssp91FD Once the wall mount is installed the position of your TV can be easily adjustable O HDMI IN 9 98 9 Cog Lie Serial Cab e 1P to 1P Not supplied Entering the menu 1 Press the MENU button to display the menu Press the A or Y button to select Setup then press the ENTER OK button 2 Press the A or Y button to select Wall Mount Adjustment then press the ENTER OK button 3 Adjust to the desired position using the A lt gt
99. with reference to the Display Modes Table You do not need to change the Colours settings 3 Click on Advanced A new settings dialog box will be displayed 4 Click on the Monitor tab then set the Screen refresh rate with reference to the Display Modes Table Set the Vertical Frequency and Horizontal Frequency individually if you can do so instead of setting the Screen refresh rate 5 Click on OK to close the window then Click on OK button to the Display Properties window Automatic rebooting may commence at this moment English 47 Display Modes Both screen position and size will vary depending on the type of PC monitor and its resolution The resolutions in the table are recommended All resolutions between the supported limits are supported D Sub Input r Horizontal Vertical Pixel Clock Sync Polarity Mode see Tcl Frequency kHz Frequency Hz Frequency MHz HIV 640 x 350 31 469 70 086 25 175 IBM 640 x 480 31 469 59 940 25 175 l 720 x 400 31 469 70 087 28 322 640 x 480 35 000 70 000 28 560 640 x 480 37 861 72 809 31 500 640 x 480 37 500 75 000 31 500 800 x 600 43 750 70 000 45 500 800 x 600 37 879 60 317 40 000 800 x 600 48 077 72 188 50 000 800 x 600 46 875 75 000 49 500 1024 x 768 57 672 72 000 78 434 VESA 1024 x 768 48 364 60 000 65 000 1024 x 768 56 476 70 069 75 000 1024 x 768 60 023 75 029 78 750 1152 x 864 67 500 75 000 108 000 128
100. ynet setup menu m Search Anynet devices again m You can connect an Anynet device using the HDMI cable only Some HDMI cables may not support Anynet functions The TV program cannot be m Check whether the antenna jack on the recording device is properly recorded connected The TV sound is not output A through the receiver Connect the optical cable between TV and the receiver want to start Anynet English 68 Teletext Feature depending on the model Most television stations provide written information services via teletext The index page of the teletext service gives you information on how to use the service In addition you can select various options to suit your requirements by using the remote control buttons H For teletext information to be displayed correctly channel reception i must be stable Otherwise information may be missing or some pages may not be displayed RETURN Exit from the teletext display depending on the model e index Used to display the index contents page at any time while you are viewing teletext H S teletext on mix Press to activate teletext mode after selecting the channel providing i the teletext service Press it twice to overlap the teletext with the current broadcasting screen 0O size Press to display the double size letters in the upper half of the screen For lower half of the screen press it again To display norm

Samsung Series 7 63inch (PS63P71FDX) User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents