Samsung AW09FANEA User Manual
Contents
1. ag Applying excessive force to remove the front panel may cause damage to the tab be sure not to use excessive force 4 Remove two screws on the lower right and left sides of the unit 5 Remove the chassis from the cabinet 6 Remove the rubber cap inserted into the basepan Drain Pan Hear J 7 Fix the drain pan as shown in the figure and then connect the drain hose You can use any commercially available drain hose 8 Install the cabinet at the specified area after installing the drain pan and then re assemble it in the original condition 1 Rubber cap Screw Drain Hose gt Secure the front panel to the case by replacing the screw removed in step 2 If a screw not removed in step 2 secure the panel with a supplied screw Bottom Side View with Drain Pan and Hose in Place In the case of an area where the drain pan can be directly installed on the rear side of the unit after installing the air conditioner 1 Follow steps 6 and 7 only THIS AIR CONDITIONER IS MANUFACTURED BY ESTE ACONDICIONADOR DE AIRE HA SIDO FABRICADO POR CE CLIMATISEUR EST FABRIQUE PAR ESTE APARELHO DE AR CONDICIONADO E FABRICADO POR QUESTO CONDIZIONATORE D ARIA E PRODOTTO DA a2. Air Flow Direction Vertically SSC o PER Z Z Z Z Z Z Z Z Again depending on the position of the unit in your room you can adjust the orientation of the outer air flow blades on the right hand side of the unit RECOMMENDATION When Adjust the blades to face Cooling Upwards Adjust the air flow blades to the desired position by pushing them upwards or downwards gt _ If you orient the air flow blades downwards and the unit operates in Cool mode for a long period of time dew may 9 Form on the surface of the blades Drip from the blades Setting the On timer T D O Z LII The On Timer enables you to switch on the air conditioner automatically after a given period time You can set the period of time from 1 hour to 24 hours You can select the On timer only when the air conditioner is off Remote Control Control Panel 1 Check that the air conditioner has been switched off if necessary press the l On Off button Power 2 Set the required mode by pressing the appropriate button 4 or on the remote control Mode button on the unit press it one or more times until the appropriate operating mode indicator lights up 3 Set the operating time by pressing 9 Timer on the remote control or 9 Timer on the unit one or more times Possible time is between 1 hour and 24 hour inclusive Result The remaining time is displayed and decreased by 1 hour Power automati
3. consent Do not connect other electric appliances to the same supply lines AW18xx The maximum permissible system impedance at the power junction box is 0 24 ohms Usually the maximum permissible mains impedance will not be exceeded when the branch to the power outlet is fed from a junction box with a rated current of 32A T a c O Z Im Air Conditioning Unit Main Parts Buttons and Display The design and shape are subject to change according to the model If a power failure occurs when the air conditioner is operating the unit is switched off Then the power returns the air conditioner starts up again automatically Inner air flow blades right left orientation EE Air outlet ir OU Air inlet inside FE Outer air flow blades Z E up down orientation uc BE Air filter ZZ The air filter is Ze EF Air inlet Outside located inside Z Z G Ventilation lever 4 The power plug may be not supplied depending on the model The type of the power plug FOODS in may differ according to the type of local power supply Power cable connection should be committed to an installation engineer Blue Brown Yellow Green L Main Power Earth Fan speed indicators LOW MED HIGH Air flow blade swing indicator Temperature Timer Energy Saver indicator settings l Temperature adjustment Umer Seting outon buttons Operatin
4. up High Med Press the button on the remote control or Press the on the unit until the indicator lights up Power Low Press the button on the remote control or Press the on the unit until the Y indicator lights up Result Each time you press a button the unit beeps eo 5 To control the direction of the air flow refer to page 10 Airing Your Room If the atmosphere in your room is stale you can air it using the Fan feature and if necessary evacuate the stale air outside 1 If you wish to evacuate stale air outside push the ventilation lever on the front of the unit to the right and the open position lt P Result The air inside the room circulates and stale air is evacuated outside Otherwise push the ventilation lever to the left and the closed position Result The air simply circulates inside the room If necessary press the On Off button Result 4 The operating mode indicator COOL or FAN on the unit comes on The air conditioner starts up in the mode selected when the unit was last used 9 The unit beeps twice If the FAN indicator is not lit up on the unit Press the button on the remote control or 9 Press the MODE button on the unit one or more times until the FAN indicator lights up Result The unit beeps each time you press MODE The air conditioner starts up in Fan mode gt You can change modes at any time 9 When the air condi
5. ELECTRONICS Printed in China
6. OWNERS INSTRUCTIONS MANUAL DE INSTRUCCIONES MANUEL D UTILISATION MANUAL DE INSTRUCOES ISTRUZIONI PER L USO EE Bs c O Z T e AWOGFBNAA AWOGA G BNAA lt AWO07FBNAA AB BA DA EA AWO7A G BNAA AB BA DA EA o AWO8FBNAA AB AWOSA G BNAA AB AWO9FBNAA BA CA DA EA EB AWO9A G BNAA BA CA DA EA EB AWI0FBDAA BA CA AW10A G BDAA BA CA AWI2FBDAA BA BC CA DA EA EB EC AW12A G BDAA BA BC CA DAVEA EB EC ME AW14FBMAA AB BA CA DA EA AW14A G BMAA AB BA CA DA EA O AWI8FBMBA BB BC BD BE DA EA EB AWI18A G BMBA BB BC BD BE DA EA EB PE AW18FBMCA CB CC AW18A G BMCA CB CC LL AWT18FBMBA BB DA EA EB AWT18A G BMBA BB DA EA EB AWT19FBMBA BB EA EB AWT19A G BMBA BB EA EB AWT20FBMBA BB AWT20A G BMBA BB i AW22FBMBA BB EA EB AW22A G BMBA BB EA EB AW24FBMBA BB BC BD EA EB AW24A G BMBA BB BC BD EA EB E AW24FBMCA CB CC CD AW24A G BMCA CB CC CD O AWT24FBMBA BB EA EB EC AWT24A G BMBA BB EA EB EC Window type Room Air Conditioner Coo Acondicionador de aire dom stico sistema de tipo ventana Refrigeraci n Climatiseur de type Fen tre Refroidissement 0 ar Condicionado de Window Type Refrigerac o Condizionatore d aria per ambienti da finestra Raffreddamento ITALIANO BOBBDDB8 04666A 6 Safety Precautions The following safety precautions must be taken when installing and using your air conditioner 1 The air conditioner must be plugged into its own specific power source which must be installed in compliance with national wiring
7. Selecting Energy Saving mode If you wish to save energy when using your air conditioner Remote Control Control Panel select the energy saving mode with the Energy Saver button 1 To select the energy saving mode press the Energy Saver button on the remote control or unit one or more times until the Energy Saver indicator lights up Result The fan and compressor cycle on and off together The fan will continue to run for a short time after the Energy Saver compressor cycles off gt f you would like the air conditioner to run in Fan mode do not press the Energy Saver button You cannot use the Fan mode in the energy saving mode 2 To stop the energy saving mode press the Energy Saver button on the remote control or unit again Hesult The fan runs at all times while the compressor cycles on and off gt If you select the Sleep Timer in the Energy Saving mode the Energy C Model Saving will be cancelled and the air conditioner will start up in the Sleep Timer mode Operating Recommendations Here are a few recommendations that you should follow when using your air conditioner Topic Recommendation Power failure If a power failure occurs when the air conditioner is operating the unit is switched off When the power returns the air conditioner starts up again automatically Temperature and Humidity Ranges The following table indicates the temperature and humidity ranges within which the air conditio
8. an the air conditioner After opening the front grille lift it up as much as possible then pull down to release it UMM SS 2 Grasp the handle on the air filter and lift it slightly and then out to the front 3 Remove all dust on the air filter with a vacuum cleaner or brush 4 When you have finished insert the air filter back into its original position 5 Wipe the surface of the unit with a neutral detergent and then wipe it again with dry cloth Be sure not to use benzene solvent or other chemical products Grille groove gt If you Then RORY JUGE Will not be using the Set the fan to FAN and let it for a few air conditioner for a hours to dry the inside of the air long period of time conditioner thoroughly Switch the air conditioner off and unplug it from the wall socket 4 Clean the filter and outer surfaces Have not used the air Set the fan to FAN and let it run for conditioner for a long a few hours to dry the inside of the air period of time conditioner thoroughly Solving Common Problems Before contacting the after sales service perform the following simple checks They may save you the time and expense of an unnecessary service call Problem The air conditioner does not operate at all The air conditioner does not operate with the remote contr
9. cally to indicate the remaining time The air conditioner switches on automatically when the operating time reaches zero gt You can change the setting mode fan speed and air flow direction after setting the On timer To Cancel the On Timer To cancel the timer press 9 Timer on the remote control or unit one or more times until EE is displayed or bonthe remote control or unit The air conditioner operates in the mode selected when the unit was last used Power Setting the Off Timer The Off Timer enables you to switch off the air conditioner automatically after a given period of time You can set the period of Remote Control Control Panel time from 1 hour to 24 hours You can select the Off timer only when the air conditioner is on 1 Check that the air conditioner has been switched on if necessary press the On Off button 2 Set the operating time by pressing 9 Timer on the remote control or 9 Timer on the unit one or more times Possible times are between 1 hour and 24 hour inclusive Result The remaining time is displayed and decreased by 1 hour automatically to indicate the remaining time The air conditioner switches off automatically when the operating time reaches zero gt You can change the setting mode fan speed and air flow direction after setting the Off timer To Cancel the Off Timer To cancel the timer press 9 Timer on the remote control or u
10. ctly see page 11 13 Air the room Technical Specifications Design and specifications are subject to change without notice Model AA AB BA BB BC BD BE CA CB CC CD DA EA EB EC Power Supply 115V 60Hz 220V 60Hz 230 208V 60Hz 200 220V 50Hz 220 240V 50Hz Installation for 60Hz T a c O Z Im 1 Electrical Requirements For personal safety This appliance must be properly grounded Do not under any circumstances cut or remove the third grounding prong from the power cord We recommend that you do not use an extension cord or an adapter plug with this appliance Do not change the plug on the power cord of this appliance Follow national electrical codes or local codes and ordinances 115V 230V 208V 230V 208V 230V 208V 15 AMP circuit 20 AMP circuit 15 AMP circuit 30 AMP circuit parallel type perpendicular type tandem type tandem type mu t tu If the electric supply provided does not meet the above specifications call a licensed electrician Aluminum house wiring may pose special problems consult a qualified electrician This unit requires a separate circuit serving only this appliance Installation Before installation be sure to check the installation area or the air conditioner and drain hose Checkpoints prior to i
11. ditioner If you are unsure about installation contact an installation specialist Contents PREPARING YOUR AIR CONDITIONER Safety Precautions in a da E Air Conditioning Unit Main Parts Buttons and Display Remote Control BULTOTIS eas bec tr ansia Getting anee Inserting the Remote Control Batteries pp OPERATING YOUR AIR CONDITIONER E Cooling YOUR ROOMY get wi ANO YOUN FRO e SEM m Adjusting the Air Flow Direction Horizontally pp m Adjusting the Air Flow Direction Vertically PROGRAMMING YOUR AIR CONDITIONER B Seld te Or TN R ecu e niens ias ax sue La AR Uri Uno lirios Mm Seng the OF TMe TUE SCUING Te SIC CD TIMET a esata LEES Selecting Energy Saving mode ed er sees teach eerie dened RECOMMENDATIONS FOR USE m Operating Recommendation pp m Temperature and Humidity RANGES pp Cleaning Your Alr COLdllloni GIF Solving Common Problems ete muto e ei A Re bra dA teed T chnical Specifications e INSTALLATION A CAUTION The high inrush current of the starting compressor motor can have adverse effects to the operation of other equipment under unfavorable mains conditions This equipment does not comply with the relevant technical standards for the limitation of voltage fluctuations and flicker Before connecting this equipment to the power supply system please report to your supply authority and obtain the
12. earthing and safety regulations Depending on national regulations and your specific installation you may need to install A circuit breaker For further information on electrical requirements contact a professional electrician This device must be installed according to the national electrical rules 2 Make sure that the unit is correctly ventilated at all times do NOT place clothing or other materials over it 3 NEVER spill liquids of any kind into the unit Should this happen unplug the unit and contact your installation specialist 4 Do NOT insert anything between the air outlet blades as it may damage the inner fan and you may be hurt Keep children away from the unit 5 ALWAYS ensure that the power cable is in good condition If the power cord is damaged in any way it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard 6 Do NOT attempt to repair the unit yourself If it is damaged in any way contact An authorized service center The dealer from whom you purchased the air conditioner 7 Do NOT place any blocking objects in front of the unit 8 Ifthe remote control will not be used for a long time remove the batteries 9 Before throwing out the device it is necessary to pull back the battery cells and get rid of them safely CAUTION The manufacturer does not assume responsibility for accidents or injury caused by an incorrectly installed air con
13. edures use four different symbols gt IMPORTANT NOTE Moreover applicable wherever the illustrations show the positions of the buttons on both the remote control and the unit itself For the The illustrations have a Remote control Gray background Example Unit itself White background Example Inserting the Remote Control Batteries T D O Z TT You must insert or replace the remote control batteries when You purchase the air conditioner The remote control does not work correctly Use two AAA LR03 1 5 V batteries Do not use old batteries or different kinds of batteries together Batteries may be completely discharged after 12 months even if they have not actually been used 1 Push the battery cover on the rear of the remote control with your thumb in the direction of the arrow and remove it 2 Insert the two batteries taking care to respect the polarities 9 on the battery with on the remote control 9 onthe battery with on the remote control 3 Close the cover by sliding it back until it clicks into place Result You can control all the functions on your air conditioning unit directly from your seat using the remote control Cooling Your Room You must select the Cool mode if you wish to lower the temperature in your Remote Control Control Panel room You can also set the fan speed 1 If necessary press the 5 On Off button Result The op
14. erating mode indicator COOL or FAN on the unit comes on The air conditioner starts up in the mode selected Power when the unit was last used 9 The unit beeps twice The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being 9 Plugged in 9 Stopped It will start up automatically after about three minutes 2 If the COOL indicator is not lit up on the unit Press the button on the remote control or Press the MODE button on the unit one or more times until the COOL indicator lights up Result 9 The unit beeps each time you press MODE The air conditioner starts up in Cool mode gt You can change modes at any time 3 To adjust the temperature press the GAS or GVA button on the remote control one or more times until the required temperature is displayed To adjust the temperature press the or button on the unit one or more times until the required temperature is displayed Possible temperatures are between 18 C and 30 C inclusive Result Each time you press the temperature buttons The temperature is adjusted by 1 C and displayed on the control panel The unit beeps The air conditioner starts cooling if the room temperature is higher than the selected temperature 4 To set the fan speed to Then Press the button on the remote control or Press the on the unit until the indicator lights
15. g mode indicators Sleep timer setting button OL FAN Timer indicator Remote Control sensor Air flow blade swing button Air Swing Energy Saver button Fan speed adjustment 7 Fan Speed button Pawar ON OFF button Operating mode selection button COOL FAN Remote Control Buttons T us O Z LII Timer setting button Temperature adjustment Sleep timer setting button buttons Operating mode selection buttons Fan speed adjustment buttons Energy Saver button Air flow blade swing button ON OFF button Getting Started You have just purchased a window type room air conditioner and it has been installed by your installation specialist Your Owner s Instructions contain valuable information on using your air conditioner Please take the time to read them as they will help you take full advantage of the unit s functions This Owner s Instructions is just for using your air conditioner correctly Thus the illustrations shown in this manual may not exactly match your air conditioners The booklet is organized as follows The following figures are shown on pages 4 and 5 Air conditioning unit main parts buttons and display Remote control buttons They will help you find the buttons and understand the symbols displayed Inthe main part of the document you will find a series of step by step procedures for each function available The illustrations in the step by step proc
16. ner can be used Mode Indoor Temperature Outdoor Temperature Indoor Humidity Cooling 21 C to 32 C approx 21 C to 43 C approx 80 or less 21 C to 54 C approx Middle East If the air conditioner is used at Then Higher temperatures The automatic protection feature may be triggered and the air conditioner stopped Lower temperatures A water leakage or some other malfunction may happen if the heat exchanger freezes Higher humidity levels Water may condense on and drip from the surface of the unit if it is used for long periods Cleaning Your Air Conditioner xFB models Be sure to clean the air filter periodically to maintain the air conditioner in the best condition for a long period of time PORTANT When cleaning the air conditioner turn it off and pull out the power plug 1 Hold the air filter handle slightly pull it to the left side and open the front grille gt The removal of the front grille makes it easier to clean the air conditioner Open the grille as much as possible CAUTION Removal and Reassembly of the Front Grille For user s safety a safety clip has been installed in the front grille 1 Grasp the lower part of the Safety clip front grille and the air filter handle then open the grille 2 Remove the safety clip and the front grille 3 When reassembling the front grille you should install the safety clip again 2 Pull the air filte
17. nit one or more times until BELA displayed or bonthe remote control or unit The air conditioner operates in the mode selected when the unit was last used IS Setting the Sleep timer T D O Z LII The Sleep Timer can be used when you are cooling your room to switch the air conditioner off automatically after a period of 8 hours gt If you wish to switch the unit off at a specific time refer to page 12 Remote Control Control Panel 1 Make sure that you have selected either COOL mode 2 Press the button on the remote control Power Press the button on the unit Result 9 Each time you press a button the unit beeps The SLEEP passes through the control panel for about 15 seconds and the BEES will be displayed 4 The remaining time is displayed and decreased by 1 hour automatically to indicate the remaining time The air conditioner will be controlled as illustration below Cooling When the temperature has been increased by 1 C after 1 hour it is maintained for 7 hours To Cancel the Sleep Timer To cancel the timer press on the remote control or on the unit Result The unit beeps 4 The SLEEP indicator is no longer displayed The air conditioner operates in the mode selected last gt If you select the Energy Saving mode in the Sleep Timer mode the Sleep Timer will be cancelled and the air conditioner will start up in the Energy Saving mode
18. nstallation 1 Check the cabinet and front grille of the unit for any harmful defects such as scratches 2 Be sure to check the power supply Refer to the specifications on the label attached to the unit Installation Conditions 1 As the unit is heavy the wall or window of the installation area should have sufficient strength and durability for operation of the air conditioner and for prevention of any vibration or noise If it is weak reinforcement work should be performed separately 2 It is advisable to install the air conditioner in the north or west side to prevent the effect of direct sunlight When installing it in the south or east side due to unavoidable circumstances it is advisable to install the sunshade to prevent the direct sunlight In this case take care not to cause any hindrance to the flow of outside air 3 When installing the air conditioner be sure to obtain sufficient space on the rear side of the unit for smooth flow of air When operating the air conditioner in closed areas such as inner building with cooling operation and result in trouble with the unit See the illustration below The appliance must be fixed well by screw or similar method Fence wall s or other OS obstacle Appr
19. ol No beep is heard when you press b On Off on the remote control The air conditioner does not cool The air flow direction does not change when you press the or on the unit button The timer is not correctly triggered Odours are permeated in the room during air conditioning Em L O Z T Explanation Solution 4 99 Check that the circuit breaker used for the air conditioner has not been triggered Check that the power cable is plugged into a wall socket and the socket is switched on if necessary Check that the operating mode indicator COOL or FAN on the unit is lit up if necessary press On Off on the remote control or unit Check that there are no obstacles between you and the unit Replace the remote control batteries if necessary Check that you are close enough to the unit seven metres yards or less Check that you are pointing the remote control at the remote control sensor on the unit Replace the remote control batteries if necessary Check that the correct operating mode has been selected COOL The room temperature may be too low Dust may be blocking the air filter refer to page 15 or 16 for cleaning instructions Check that there is no obstacle blocking the air flow into or out of the unit Check that the air conditioner has been switched on if necessary press 5 On Off on the remote control or unit Check that the timer has been programmed corre
20. ox 3 A OC JI 150mm min PKNK T Oo O x OY FAO So D O c O bos M 240mm O o D 200200 90 090 joO o 0 0 3098909 Ook 0020 0 9 Oo90090 09 Oo oO 0 10 N0 fone y gt Zo iy Oc 0 000 YO Zo er O05 o0 Jos Jo a Y gt 00000 O Osa Joal J o 89 Uo 00 0 OW J oQ9 590 oO0U 000 JoOV700 7959 U9560V700 If the wall is greater than 150mm thick cut the wall back on a 45 angle if possible 100mm or more Em L O Z T Installation of the Drain Tube Fix the drain tube as shown in the figure Screws 2EA Installation of the Drain Pan The procedure for installing the drain pan should be determined by the condition of the installing area In the case of an area where the drain pan can not be directly installed on the rear side of the unit after installing the air conditioner Example High storage 1 Open the front grille refer to page 15 or 16 2 Remove the screw located at the lower section of the front grille It is secured in the lt section depending on the model 3 Remove the front panel 3 1 Press both sides of the cabinet in the direction of the arrow e as shown in the figure 3 2 Pull the lower part of the front panel slightly forward Front panel as below three inches F lt Screw 3 3 Lift the front panel upward
21. r to the right side 3 Remove all dust on the air filter with a vacuum cleaner or brush 4 When you have finished insert the air filter back into its original position 5 Wipe the surface of the unit with a neutral detergent and then wipe it again with dry cloth Be sure not to use benzene solvent or other chemical products gt Ifyou Then Will not be using the Set the fan going for a few hours to air conditioner for a dry the inside of the air conditioner long period of time thoroughly Switch the air conditioner off and unplug it from the wall socket Clean the filter and outer surfaces Have not used the air Set the fan going for a few hours to dry conditioner for along the inside of the air conditioner period of time thoroughly Em L O Z T E ISS yy UMMM o The air conditioner has two or three grille grooves depending on the model Cleaning Your Air Conditioner AB GB models Be sure to clean the air filter periodically to maintain the air conditioner in the best condition for a long period of time When cleaning the air conditioner turn it off and pull out the power plug 1 Open the front grille by pulling on the tabs of the unit W W Ww i Ww NW gt The removal of the front grille makes it easier to cle
22. tioner is in Fan mode the temperature is not displayed in this case you do not need to set the temperature To set the fan speed to Then High Press the button on the remote control or Press the on the unit until the amp indicator lights up Med Press the button on the remote control or Press the on the unit until the indicator lights up Low Press the button on the remote control or Press the on the unit until the indicator lights up Result Each time you press a button the unit beeps To control the direction of the air flow refer to page 10 Remote Control Control Panel Power T D O Z LII Adjusting the Air Flow Direction Horizontally Remote Control Control Panel Power Depending on the position of the unit in your room you can adjust the orientation of the inner air flow blades on the right hand side of the unit thus increasing the efficiency of the air conditioner 1 Press the or on the unit button on the remote control Result The inner blades swing automatically left and right 2 To stop the blades moving left and right press the or on the unit button on the remote control gt To stop the blades in a specific position and orient the air flow in the corresponding direction simply press the or rs on the unit button on the remote control when the blades are in the desired position Adjusting the
Download Pdf Manuals
Related Search