Samsung SH09CA1 User Manual
Contents
1. Problem Explanation Solution The air conditioner does not Check that the breaker used for the air conditioner is switched on operate at all Check that the OPERATION indicator on the indoor unit is on if necessary press the On Off button on the remote control Check whether the TIMER indicator on the indoor unit is switched on If so Wait until the switch on time is reached and the air conditioner starts up automatically Cancel the timer see pages 16 and 17 for further details The air conditioner does not 4 Check that there are no obstacles between you and the indoor unit operate with the remote control Check the remote control batteries 4 Check that you are close enough to the indoor unit seven metres yards or less No beep is heard when you press Check that you are pointing the remote control at the remote control the On Off on the remote sensor in the right of the indoor unit control 4 Replace the remote control batteries if necessary The air conditioner does not cool Check that the correct operating mode has been selected AUTO or heat COOL HEAT 4 The room temperature may be too low or too high Dust may be blocking the air filter guard refer to page 20 for cleaning instructions 4 Check that there is no obstacle in front of the outdoor unit When heating the required room 4 Check that the required temperature has been set correctly temperature is never reached and Increase the fan2. intervention is required from you after about seven minutes the air conditioner starts operating again normally If both the indoor and outdoor temperatures are high and you select the Heat mode the outdoor unit s fan and compressor may stop at times This is normal simply wait until the air conditioner switches on again Power failure If a power failure occurs when the air conditioner is operating the unit is switched off When the power returns you must press the ON OFF button to restart it ENGLISH Temperature and Humidity Ranges The following table indicates the temperature and humidity ranges within which the air conditioner can be used If the air conditioner is used at Then High temperatures The automatic protection feature may be triggered and the air conditioner stopped Low temperatures A water leakage or some other malfunction may happen if the heat exchanger freezes High humidity levels Water may condense on and drip from the surface of the indoor unit if it is used for long periods Mode Outdoor Temperature Indoor Temperature Indoor Humidity Heating 0 C to 24 C approx 27 C or less Cooling 21 C to 43 C approx 18 C to 32 approx 80 or less Drying 18 to 43 C approx 18 C to 32 approx If the heating operation is used at below 0 C outdoor temperature then does not a full capacity If the cooling operation is used at over 33 C indoor temp
3. the standard temperature and the optimum fan speed is selected automatically You can adjust the standard temperature but not the fan speed 1 If necessary press the On Off button Result The OPERATION indicator on the indoor unit comes on On Timer The air conditioner starts up in the mode selected when the unit was last used Off Timer The indoor unit beeps eS PORTANT The air conditioner is fitted with a protection mechanism to 70 prevent the unit from being damaged when it is started immediately after being 4 Plugged in Stopped It will start up normally after three minutes 2 Ifthe ab is not displayed at the top of the remote control a press the MODE button on the remote control one or more times until it Mode appears Result The indoor unit beeps each time you press the MODE button 4 The air conditioner runs in AUTO mode Turbo E Note You can change modes at any time 3 To adjust the standard temperature The air conditioner automatically set the standard temperature by the current room temperature press the TEMPERATURE buttons one or more times lt SET TEMP SET TEMP SET TEMP SET TEMP Ce 2 C 1 C Standard temperature 1 2 2 lt When you feel hot gt lt When you feel chilly gt Turbo E Cooling Your Room You must select the Cool mode if you wish to adjust the Cooling temperature Fan speed when cooling 1 If necessary press the On
4. FF switch again Note Even if the air conditioner has been switched on via the ON OFF switch operations can still be controlled using the remote control as usual Installing a Filter Option The air conditioner can be fitted with a deodorizing and Bio Pure filter to remove minute dust particles or odours The service life of the filter is approximately three months depending on the time during which the air conditioner is used 1 Remove the vinyl packing from the filter Note Do not remove the packing from a deodorizing filter until you peogonzing wish to use the filter as it will lose its properties filter 2 Insert the filter the filter holder and press the three insert tabs until Bio Pure Filter you hear a click 3 Open the front grille by pulling on the tabs on the lower right and left sides of the indoor unit 4 Take out the existing filter and replace it with the new one Technical Specifications Model Indoor unit Power Supply AQ07ACVE AQ09ACVE AQ12ACVE SH07CA1 SH09CA1 SH12CA1 Package Weight 220 240V 50Hz Model Paper Plastic Wood AQO7ACVE SHO7CA1 3 35kg 0 49kg AQO9ACVE AQ12ACVE vaca 3 81kg 0 61kg SH12CA1 ENGLISH THIS AIR CONDITIONER IS MANUFACTURED BY ESTE AIRE ACONDICIONADO HA SIDO FABRICADO POR QUESTO CONDIZIONATORE D ARIA E PRODOTTO DA ESTE APARELHO DE AR CONDICIONADO E FABRICADO POR CE CLIM ATISEUR EST FABRIQUE PAR DIESE K
5. LIM AANLAGE IST FABRIZIERT VON AYTH H ZYZKEYH KATA2KEYA2THKE ANO ID ELECTRONICS Printed in Korea
6. ONDITIONER m Selecting the Automatic Operating Mode m Cooling Your Room m Heating Your Room 10 m Changing the Room Temperature Quickly 11 m Removing Excess Humidity 12 m Airing Your Room 13 m Adjusting the Air Flow Direction Vertically 14 m Adjusting the Air Flow Direction Horizontally 15 PROGRAMMING YOUR AIR CONDITIONER m Setting the On 16 m Setting the Off 17 m Setting the Sleep 18 RECOMMENDATIONS FOR USE m Operating Recommendations 19 m Temperature and Humidity 20 m Cleaning Your Air Conditioner 20 mg Solving Common Problems 21 m Operating Your Air Conditioner Without the Remote Control 22 Installing a Filter Option 22 TECHNICAL SPECIFICATIONS ENGLISH View of the Indoor Unit The design and shape are subject to change according to the model ON OFF switch operation without remote control Air Filter under the grille Air flow blades outlet Remote control sensor Air Inlet OPERATION TIMER FAN TURBO
7. OWNER S INSTRUCTIONS MANUAL DE INSTRUCCIONES ISTRUZIONI PER L USO MANUAL DE INSTRUCOES MANUEL D UTILISATION GEBRAUCHSANWEISUNG OAHTIEZ Indoor Unit AQO7ACVE AQO9ACVE AQI2ACVE SHO7CA1 SHO9CA1 SH12CA1 ENGLISH Split type Room Air Conditioner Cool and Heat Aire acondicionado dom stico sistema Split Refrigeraci n y Calefacci n Condizionatore d aria per ambienti ad unit Separate Raffreddamento e Riscaldamento Aparelho de ar condicionado tipo Split Refrigerac o e Aquecimento Climatiseur de type S par Refroidissement et Chauffage Geteilte raumklimaanlage K hlen und W rmen AIAIPOYMENO KAIMATIZTIKO AOMATIOY W gnc kai O ppavonc d dE BS 0 BPXPDG DB68 01273A 3 Safety Precautions The following safety precautions must be taken when using your air conditioner 1 ake sure that the indoor unit is correctly ventilated at all times do NOT place clothing or other materials over it 2 NEVER spill liquid of any kind into the indoor unit Should this happen switch off the breaker used for your air conditioner and contact your installation specialist 3 Do NOT insert anything between the air flow blades as the inner fan may be damaged and you may be hurt Keep children away from the indoor unit 4 DoNOT place any obstacles in front of the outdoor unit 5 If the remote control will not be used for a long time remove the batteries 6 Users of this product are cautioned not to at
8. Off button Result 4 The OPERATION indicator on the indoor unit comes on The air conditioner starts up in the mode selected when the unit was last used 4 The indoor unit beeps PORTANT The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being Plugged in Stopped It will start up normally after three minutes 2 Ifthe is not displayed at the top of the remote control press the MODE button on the remote control one or more times until it appears Result The indoor unit beeps each time you press the MODE button The air conditioner runs in COOL mode Note You can change modes at any time 3 To adjust the temperature press the TEMPERATURE buttons one or more times until the required temperature is displayed Possible temperatures are between 18 C and 30 C inclusive Result Each time you press the TEMPERATURE buttons The temperature is adjusted by 1 C The indoor unit beeps The air conditioner starts cooling provided that the room temperature is higher than the selected temperature the fan will however operate 4 Select the fan speed by pressing the FAN button one or more times until the required setting is displayed f Automatic rotated gt fur Sul a Low a Medium Sul High Result Each time you press the FAN button the indoor unit beeps 5 To control the direction
9. PERATURE buttons after setting the On timer To Cancel the On Timer 1 Tocancelthe On Timer press the ON TIMER button one or more times until the timer setting disappears 2 Press the Set Cancel button ff Ti Note Ifyou want to turn on the air conditioner before the timer reaches the setting time press the ON OFF button 9h Setting the Off Timer The Off Timer enables you to switch off the air conditioner automatically after a given period of time You can set the period of time from 30 minutes to 24 hours 1 To set the operating time press the OFF TIMER button one or more times until the required time is displayed Possible time is between 0 5 hour and 24 hour inclusive Result Each time you press OFF TIMER button The time is adjusted by 0 5 hour to 5 hours by 1 hour from 6 hours to 24 hours 2 Pressthe Set Cancel button to complete the setting Result The remaining time is displayed 4 Blinking of the timer indicator stops The selected mode and the temperature disappear on the display after 5 seconds The TIMER indicator on the indoor unit lights up yellow 4 The air conditioner will switch off automatically when the counter displayed on the remote control reaches the setting time as disappearing the Off timer setting If you would like to turn the air conditioner on after 2 hours and to operate it for 2 hours 1 Press the ON TIMER bu
10. air conditioner starts heating provided that the room temperature is lower than the desired temperature selected temperature 3 C the fan will however operate 4 Select the fan speed by pressing the FAN button one or more times until the required setting is displayed 11 Automatic rotated h gt ul a Low Sl Medium Sail High Result Each time you press the FAN button the indoor unit beeps For the first three to five minutes the fan operates very slowly until the air has been sufficiently warmed Once the correct temperature has been reached the fan is automatically set to the required speed 5 control the direction of the air flow refer to page 14 and 15 Changing the Room Temperature Quickly The Turbo cooling heating function is used to cool or heat your room as quickly as possible Example You have just come home and find that the room is very hot You wish to cool it down as quickly as possible The Turbo function operates for 30 minutes with the maximum settings before retuming automatically to the mode and temperature previously selected 1 If necessary press the button Result 4 The OPERATION indicator on the indoor unit comes on The air conditioner starts up in the mode selected when the unit was last used 4 The indoor unit beeps 2 Press the Gute button Result The temperature and fan settings are adjusted automatically 4 The TURBO indicato
11. automatically Note You can change modes at any time Turbo E 3 Select the fan speed by pressing the FAN button one or more times until the required setting is displayed DAP Low PAM Medium ul High Result Each time you press the FAN button the indoor unit beeps ful vy On Timer 4 Tocontrol the direction of the air flow refer to page 14 and 15 Adjusting the Air Flow Direction Vertically Depending on the position of the indoor unit on the wall of your room you can adjust the position of the outer air flow blade on the bottom of the unit thus increasing the efficiency of the air conditioner 1 Press the SWING button one or more times as required Result The outer blade is adjusted vertically RECOMMENDATION When Adjust the blade to face Cooling Upwards Heating Downwards On Timer Y Off Timer 2 If you want the blade to move up and down automatically when the air conditioner is operating press the SWING button Result The blade move up and down around the base position set 3 To stop the blade moving up and down press the SWING button again Note If you switch the air conditioner Then the blade is Off Closed completely On again Reset to the position that you previously selected Adjusting the Air Flow Direction Horizontally There are two sets of inner air flow blades J ust as the outer air flow blade can be adjusted vertically the inner blades can be adjust
12. ed horizontally 1 Open the air flow blade along the bottom of the indoor unit by pressing the SWING button On Timer 2 To stop the blade moving up and down press the SWING button Off Timer again 3 Adjust each set of inner blades to the required position by pushing or pulling them sideways ENGLISH CTE LU Coe Setting the On Timer The On Timer enables you to switch on the air conditioner automatically after a given period of time You can set the period of time from 30 minutes to 24 hours 1 To set the operating time press the ON TIMER button one or more times until the required time is displayed Possible time is between 0 5 hour and 4 24 hour inclusive Result Each time you press ON TIMER button The time is adjusted by 0 5 hour to 5 hours by 1 hour from 20 6 hours to 24 hours Off Timer 2 Press the E Set Cancel button to complete the setting Result The remaining time is displayed 4 Blinking of the timer indicator stops The selected mode and the temperature disappear on the display after 5 seconds The TIMER indicator on the indoor unit lights up yellow 2 4 The air conditioner will switch on automatically when the counter displayed on the remote control reaches the setting time as disappearing the On timer setting ce Note Yon can see or change the setting mode and or the temperature w by pressing the MODE button or the TEM
13. erature then does not a full capacity Cleaning Your Air Conditioner To get the best possible use out of your air conditioner you must clean it regularly to remove the dust that accumulates on the air filter portant Before cleaning your air conditioner ensure that you have switched off the breaker used for the unit 1 Open the front grille by pulling on the tabs on the lower right and left sides of the indoor unit 2 Lift out the bottom edge of the air filters and pull down to release them 3 Remove all dust on the air filters with a vacuum cleaner or brush 4 When you have finished insert the top part of the filters into their slot and push down on the bottom edge until they click into place Body groove 5 Clean the front panel with a damp cloth and mild detergent do NOT use benzene solvents or other chemicals Note If you have not used the air conditioner for a long period of time set the fan going for three to four hours to dry the inside of the air conditioner thoroughly The removal of the front grille facilitates your cleaning the air conditioner After opening the front grille lift up to the max push slightly to the left and pull down to release them and vice versa Solving Common Problems ENGLISH Before contacting the after sales service perform the following simple checks They may save you the time and expense of an unnecessary call
14. lt q um OPERATION indicator L TURBO indicator Operation GREEN RED Deice RED TIMER indicator FAN indicator YELLOW GREEN View of the Outdoor Unit SH12CA1X UQO7ACVE Air Inlet UQ09 12ACVE Air Inlet SHO7CA1X SHO9CA1X Connection Valve ion Val Air Outlet Air Outlet Connection Valve Remote Control Buttons and Display ENGLISH Remote control transmission indicator Operating mode amp AUTO COOL DRY FAN X HEAT Mode selection button AUTO COOL DRY FAN HEAT SD Temperature adjustment SET buttons Temperature setting BH Turbo mode T W e G y 4 Turbo Sleep mode Sleep mode Selection button Fan speed Fan speed adjustment ml a button Air flow direction r7 Swing button On Timer setting 3 8 Timer button Off Timer setting A Off Timer button Battery discharge indicator On Off amp Timer Set Cancel button Getting Started UUUEE You have just purchased a split type air conditioner and it has been i installed by your installation specialist Your Owner s Instructions contain much valuable information on using your air conditioner Please take
15. n decreased Set by 2 C after two hours the TEMP temperature is maintained for four hours To Cancel the Sleep Timer If you no longer wish to use the Sleep Timer that you have set you can cancel it at any time Press the amp button Result The indoor unit beeps The is no longer displayed The air conditioner operates normally Operating Recommendations Here are a few recommendations that you should follow when using your air conditioner Topic Recommendation Heating performances The heat pump inside the air conditioner absorbs heat from outside air and brings it indoors If the temperature of the outside air drops the air conditioner will heat less If you find that the room is not warm enough use an additional heating appliance Warm air circulation The air conditioner circulates warm air to heat your room as a result some time will be required after starting the air conditioner to warm the entire room If necessary set the air conditioner going a short time before you wish to use the room Frost High indoor and outdoor temperatures When outside temperatures are low and humidity is high frost may form in the outdoor unit when heating with your air conditioner If this happens 4 The heating operation is stopped The Deice mode is triggered automatically for about seven minutes The OPERATION indicator on the indoor unit lights up red No
16. of the air flow refer to page 14 and 15 ES LE zc Sul ENGLISH On Timer Off Timer Turbo O y Turbo E Turbo E On Timer Mff Timor Heating Your Room On Timer Off Timer Turbo ie es co KZ Turbo E ee I lt On Timer You must select the Heat mode if you wish to adjust the Heating temperature Fan speed when heating 1 If necessary press the On Off button Result The OPERATION indicator on the indoor unit comes on The air conditioner starts up in the mode selected when the unit was last used The indoor unit beeps PORTANT The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being Plugged in Stopped It will start up normally after three minutes 2 Ifthe o is not displayed at the top of the remote control press the MODE button on the remote control one or more times until it appears Result The indoor unit beeps each time you press the MODE button The air conditioner runs in HEAT mode Note You can change modes at any time 3 To adjust the temperature press the TEMPERATURE buttons one or more times until the required temperature is displayed Possible temperatures are between 16 C and 30 C inclusive Result Each time you press the TEMPERATURE buttons The temperature is adjusted by 1 C The indoor unit beeps The
17. ote control press the MODE button on the remote control one or more times until it appears Result The indoor unit beeps each time you press the MODE button The air conditioner runs in DRY mode Note You can change modes at any time Turbo S 3 To adjust the temperature press the TEMPERATURE buttons one or more times until the required temperature is displayed Possible temperatures are between 18 C and 30 C inclusive Result Each time you press the TEMPERATURE buttons The temperature is adjusted by 1 C CC The indoor unit beeps IN The air conditioner starts removing the excess humidity g the quantity of air is adjusted automatically Turbo E 4 To control the direction of the air flow refer to page 14 and 15 Airing Your Room ENGLISH If the atmosphere in your room is stale you can air the room using the Fan feature 1 If necessary press the Q2 On Off button Result The OPERATION indicator on the indoor unit comes on On Timer The air conditioner starts in the mode selected when the unit was last used Off Timer The indoor unit beeps 2 Ifthe of is not displayed at the top of the remote control press the MODE button on the remote control one or more times until it appears Result 4 The indoor unit beeps each time you press the MODE button The FAN indicator on the indoor unit lights up Y The air conditioner runs in FAN mode The temperature is set
18. r on the indoor unit comes on The air conditioner cools or heats the room as quickly as possible After 30 minutes the air conditioner is reset automatically to the previous mode temperature and fan settings But if you press the amp button in DRY or FAN mode that is changed with AUTO mode automatically 3 If you wish to stop the Turbo function before the end of the 30 minute period press the fe button one or more times until or disappears Result The air conditioner is reset automatically to the previous mode temperature and fan settings But if you press the Gu button in DRY or FAN mode that is changed with AUTO mode automatically 4 control the direction of the air flow refer to page 14 and 15 ENGLISH Removing Excess Humidity e If the atmosphere in your room is very humid or damp you can remove excess humidity without lowering the room temperature too much 1 If necessary press button On Timer Result The OPERATION indicator on the indoor unit comes on The air conditioner starts up in the mode selected when Off Timer the unit was last used The indoor unit beeps CA PORTANT The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being Plugged in Stopped It will start up normally after three minutes 2 Ifthe e is not displayed at the top of the rem
19. speed the air conditioner frequently stops If the air flow is directed downwards use the remote control to direct it upwards The fan speed does not change Check that the operating mode is set to COOL HEAT or FAN in the when you press the FAN button AUTO mode the fan speed changes automatically and in the DRY mode it is set to AUTO The air flow direction does not Check that the air conditioner has been switched on if necessary change when you press the press the EN On Off button on the remote control SWING button The timer is not correctly triggered Check that the timer has been programmed correctly see pages 16 and 17 Odours are permeated in the room Air the room during air conditioning Operating Your Air Conditioner Without the Remote Control Your air conditioner can be operated directly from the indoor unit if the remote control is lost or broken 1 Open the front grille by pulling on the tabs on the lower right and left sides of the indoor unit 2 To switch the air conditioner on press the ON OFF switch on the right side of the indoor unit Result 4 The OPERATION indicator on the indoor unit comes on The indoor unit beeps The air conditioner starts up in the most suitable mode for the room temperature Room Temperature Operating Mode Temperature Setting Less than 21 C Heat 22 C approx 21 C or above Cool 24 C approx 3 To switch the air conditioner off press the ON O
20. tempt repair of this product at their own discretion nstead they are requested to directly contact a designated service center or the outlet at which the product was purchased 7 If the supply cord is damaged it must be replaced by a special cord or assembly available from the manufacturer or its service agent 8 This device must be installed according to the national electrical rules 9 Before throwing out the device it is necessary to pull back the battery cells and get rid of them safely 10 The appliance is not intended for use by young children or infirm person without supervision young children should be supervised to ensure that they do not play with the appliance CAUTION The manufacturer do not take the responsibility of the accident happened because the air conditioner is not fixed firmly or installed securely during installing or using the product In case you have difficulty in installation you must ask for an installation specialist help The accident will be hap pened in case of installing improperly Contents PREPARING YOUR AIR CONDITIONER m Safety Precautions m View of the Indoor Unit View of the Outdoo Unit Remote Control Buttons and Display m Getting Started m Inserting the Remote Control Batteries OPERATING YOUR AIR C
21. the time to read them as they will help you take full advantage of the unit s features l The booklet is organized as follows The following figures are shown on pages from 4 to 5 Indoor and outdoor units Remote control buttons and display They will help you find the buttons and understand the symbols displayed Inthe main part of the document you will find a series of step by step procedures for each function available The illustrations in the step by step procedures use three different symbols HOLD DOWN Inserting the Remote Control Batteries ENGLISH You must insert or replace the remote control batteries when You purchase the air conditioner The remote control does not work correctly Note Use two AAA LRO3 1 5V batteries Do not use old batteries or different kinds of batteries together Batteries may be completely discharged after 12 months even if they have not actually been used 1 Push the battery cover on the rear of the remote control with your thumb in the direction of the arrow and remove it 2 Insert the two batteries taking to respect the polarities 4 on the battery with on the remote control 4 on the battery with on the remote control 3 Close the cover by sliding it back until it clicks into place Selecting the Automatic Operating Mode You can start the air conditioner in Automatic mode from your remote control In the Automatic mode
22. tton until 2 0 Hr is displayed 2 Press the Set Cancel button 3 Press the OFF TIMER button until 4 0 Hr is displayed 4 Press the Set Cancel button Note Yon can see or change the setting mode and or the temperature by pressing the MODE button or the TEMPERATURE buttons after setting the Off timer To Cancel the Off Timer 1 To cancel the Off Timer press the OFF TIMER button one or more times until the timer setting disappears 2 Pressthe Ed Set Cancel button Note If you want to turn off the air conditioner before the timer reaches the setting time press the ON OFF button gt ENGLISH Setting the Sleep Timer ay The Sleep Timer can be used when you are cooling or heating your room to switch the air conditioner off automatically after a period of six hours Note If you wish to switch the unit off at a specific time refer to page 17 1 Make sure that you have selected either COOL or HEAT mode 2 Press the button one or more times until appears on the remote control Result 4 The indoor unit beeps The air conditioner will be controlled as indicated in the illustrations below Cooling The temperature is increased by 1 C every hour When it has been increased by 2 C after two hours the Set temperature is maintained for TEMP four hours Heating The temperature is decreased by 1 C every hour When it has bee
Download Pdf Manuals
Related Search