Samsung AS09BPAX User Manual
Contents
1. The heating operation is stopped The air conditioner defrosts automatically for about 7 minutes After about 7 minutes the air conditioner starts operating again normally High indoor and outdoor If both the indoor and outdoor temperatures temperatures are high when you select the Heat mode the fan and the compressor of the outdoor unit may stop at times This is normal wait until the air conditioner turns on again Power failure If power failure occurs when the air conditioner is operating the air conditioner turns off When the power returns the air conditioner starts up again automatically Protection mechanism When the air conditioner is started immediately after being plugged in or stopped the normal operation starts up after 3 minutes for the reason of protection Temperature and Humidity Ranges If you check the following tables you can use your air conditioner more efficientiy If the air conditioner is used at Then High temperatures The air conditioner may stop operating for the reason of protection Low temperatures Water may leak and some malfunction may occur if the heat exchanger freezes High humidity levels Water may condense and drip from the surface of the indoor unit if you don t use the air conditioner for a long time Operation Outdoor Temperature Indoor Temperature Indoor Humidity Heating 0 C to 24 C approx 27 C or less Cooling 21 C to 43 C approx 16 C to 32. C Result Each time you press the button The temperature is adjusted by 1 C The indoor unit beeps The fan speed is adjusted automatically 2 fan speed indicators increase and decrease continuously and turn round Control Panel v Selecting the Cool Mode You can select the Cool mode if you want to cool your room You can adjust the temperature and the fan speed when cooling 1 If necessary press the On Off button Result The operation indicator on the indoor unit lights up The air conditioner starts up in the mode you selected last a The indoor unit beeps O ao C Mode Digital On Off 2 O Mode Press the O button on the remote control until is displayed Result 4 The indoor unit beeps each time you press the O button The air conditioner runs in the Cool mode Mr lt p Note You can change modes at any time lt gt Press the QIO button to adjust the temperature until the required temperature is displayed You can set the temperature between 16 C and 30 C Result 4 Each time you press the QIO button The temperature is adjusted by 1 C The indoor unit beeps If the room temperature is higher than the selected temperature the air conditioner starts cooling If the room temperature reaches the set temperature the air conditioner stops cooling but the fan operates consistently Press the amp button to select the fan
3. room temperature reaches 5 C higher than the set temperature the air conditioner stops heating but the fan operates consistently If the room temperature reaches 3 C lower than the set temperature the air conditioner starts heating again 4 Press the amp button to select the fan speed until the required setting is displayed Ga Automatic rotated E gt AR gt Gam Low Medium lt a High Result 4 Each time you press the amp button the indoor unit beeps The fan speed indicator increases and decreases continuously and turns round each time you press the amp button For the first 3 5 minutes the fan may not operate to prevent cool air from flowing out of the indoor unit It helps to warm the air in your room sufficiently Note The fan speed indicator of the indoor unit varies according to the temperature in the Automatic fan speed Y 5 To control the airflow direction refer to page 19 Selecting the Dry Mode You can select the Dry mode if you want to dehumidify your room You can adjust the temperature in this mode 1 If necessary press the On Off button Result 4 The operation indicator on the indoor unit lights up The air conditioner starts up in the mode you selected last 4 The indoor unit beeps QIO Mode Digital On Off O Mode 2 Press the O button on the remote control until amp is displayed Mode Result 4
4. selected repeatedly q On y Of Selecting the Anions Function Ze ALLIS et A The air conditioner can generate anions with an ionizer in the indoor unit Since it is an additional function you can select it in any mode even when the air conditioner is turned off ES 1 Press the button Result 4 The air conditioner generates anions The indoor unit beeps Note Ifyou press the ja button when the air conditioner is off the air conditioner turns on automatically and generates anions in the Fan mode with Low fan speed o 2 Press the a button again to stop the Anions function Result The air conditioner is reset automatically to the previous mode temperature and fan settings 3 To control the airflow direction refer to page 19 Adjusting the Airflow Direction Vertically ENGLISH You can adjust the airflow direction vertically The outer airflow blade moves up and down to increase the efficiency of the cooling or heating operation 1 Press the amp button until the required direction is set Result The outer blade is adjusted vertically 2 Press the amp button again to move the blade up and down i automatically during operation 3 Press the S button again to stop the blade moving up and down Note If you turn the air conditioner Then the blade Of is closed completely On set to the default position Adjusting the
5. speed until the required setting is displayed Gaa Automatic rotated gt E YA gt Ka lt lt Low amp Medium a High Result 4 Each time you press the amp button the indoor unit beeps The fan speed indicator increases and decreases continuously and turns round each time you press the button Note The fan speed indicator of the indoor unit varies according to the temperature in the Automatic fan speed Control Panel w 5 To control the airflow direction refer to page 19 Selecting the Heat Mode You can select the Heat mode if you want to heat your room You can adjust the temperature and the fan speed when heating ENGLISH 1 If necessary press the On Off button Result o The operation indicator on the indoor unit lights up The air conditioner starts up in the mode you selected last The indoor unit beeps 4 O ao CD Mode Digital On Off jode j a 2 Press the O button on the remote control until O is displayed Result 4 The indoor unit beeps each time you press the O button O The air conditioner runs in the Heat mode 7 Note You can change modes at any time 3 Press the QIO button to adjust the temperature until the required tem perature is displayed You can set the temperature between 16 C and 30 C Result 4 Each time you press the QIO button The temperature is adjusted by 1 C The indoor unit beeps If the
6. 2 C approx 80 or less Dehumidifying 18 C to 43 C approx 16 C to 32 C approx x If the outdoor temperature is as low as 0 C the heating capacity drops up to 70 80 depending on the operating condition If you use the air conditioner over 32 C indoor temperature the cooling capacity may drop Operating Your Air Conditioner Without the Remote Control ENGLISH You can operate your air conditioner directly without the remote control 2 To turn the air conditioner on press the On Off button in the front grille of the indoor unit Result 4 The Operation indicator on the indoor unit lights up The indoor unit beeps The air conditioner starts up in the appropriate mode for the room temperature The air conditioner changes the Cool or Heat mode automatically depending on the current temperature during operation 1 Open the front grille HO eye He 0 Room Temperature Operating Mode G Lower than 21 C Heating Higher than 21 C Cooling 3 To turn the air conditioner off press the On Off button again Note Even if you turned the air conditioner on with the On Off button you can control it with the remote control Troubleshooting Guide Before contacting the service center check the following It will save your time and the expense of an unnecessary call Problem Explanation Solution The air conditioner does not operate The air conditioner does not operate with the remote cont
7. Airflow Direction Horizontally You can adjust the airflow direction horizontally manually The inner blades with small fins moves the air in the required direction 1 Adjust the inner blades by moving them to left or right Setting the On Timer 5 bey BL You can set the On Timer to turn on the air conditioner automatically at the appointed time You can set the time from 30 minutes to 24 hours On 1 Press the S button until the required time is displayed to set the On Timer You can set the time between 0 5 hour and 24 hours Timer 2 Press the e button to complete the setting Result 4 The remaining time is displayed 4 The timer indicator stops blinking 4 The selected mode and the temperature on the display disappear after 10 seconds The air conditioner turns on automatically at the appointed time and the On Timer setting disappears Mode 3 Press the O button until the desired mode is displayed at the top of the remote control to select the mode in advance Result The air conditioner operates in the selected mode when it is turned on To Cancel the On Timer Press the ae button to cancel the On Timer Timer Note Ifyou press the la button both the On Timer and the Off Timer are canceled Setting the Off Timer ENGLISH You can set the Off Timer to turn off the air conditioner automatically at the appointed time You can set the time from 30 minutes to 24 hou
8. The indoor unit beeps each time you press the O button The air conditioner runs in the Dry mode Note You can change modes at any time 3 Press the MIO button to adjust the temperature until the required temperature is displayed You can set the temperature between 18 C and 30 C Result o Each time you press the QIO button The temperature is adjusted by 1 C The indoor unit beeps The air conditioner starts dehumidifying and the fan speed is adjusted automatically 4 To control the airflow direction refer to page 19 Selecting the Fan Mode You can select the Fan mode if you want to ventilate your room It helps to refresh the air in your room You can adjust the fan speed in this mode 1 If necessary press the On Off button Result 4 The operation indicator on the indoor unit lights up The air conditioner starts up in the mode you selected last The indoor unit beeps Mode 2 Press the O button on the remote control until is displayed Result 4 The indoor unit beeps each time you press the button 4 The air conditioner runs in the Fan mode 4 The temperature is set automatically Note You can change modes at any time 3 Press the amp button to select the fan speed until the required setting is displayed Low lt Medium lt High Result 4 Each time you press the amp button the indoor unit beeps The fan speed indicator increases and decre
9. USER S MANUAL MANUAL DE USUARIO MANUEL DE LUTILISATEUR MANUALE D UTENE _ MAUNAL DE INSTRUCOES BENUTZERHANDBUCH OAHFIEZ XPHETH Indoor unit Outdoor unit ASO9BPAN ASO9BPAX ASO9BPBN ASO9BPBX AS12BPAN AS12BPAX AS12BPBN AS12BPBX AS18BPAN AS18BPAX AS18BPBN AS18BPBX AS24BPAN AS24BPAX AS24BPBN AS24BPBX Split type Air Conditioner Cooling and Heating Acondicionador de aire de tipo partido Enfriamiento y Calefaccion Climatiseur de type Split R frig ration amp Chauffage Tipo Split Aria Condizionata Raffredamento e Riscaldamento Aparelho de ar condicionado tipo Split Refrigera o e Aquecimento Split Typ Klimaanlage K hlen and Heizen Ala po yeve KA yar oT k amp Xuokeu amp Awyariou W Eng Kal O pyavan ESEDPDE DB98 23940A 1 EN ESPANOL i ITALIANO e ww gt 9 gt RK O e E O 192 Er m a lt x Z T lt lt Lu Register your product at www samsung com global register Safety Precautions You should take the following safety precautions when using your air conditioner N WA RNING e If you dont follow the safety precautions you may get the risk of an electric shock injury or death e The manufacturer or qualified service personnel must install this air conditioner e Turn off the electric power before repairing installing or cleaning DURING OPERATION Do not repair the air conditioner at your discretion It is recommended to contact a service ce
10. a long time select the Fan mode for 3 to 4 hours to dry the inside of the air conditioner Cleaning Anti Allergy and Deodorizing Filter Option There are Anti Allergy and Deodorizing filters inside your air conditioner They remove odours and dust in your room You should clean the filters every 3 months 1 Open the upper front grille by pulling the lower right and left tabs of the grille 2 Pull out the Anti Allergy and Deodorizing filter 3 Wash the filters with clean water then dry them in the shade Deodorizing Filter Anti Allergy Filter 4 Insert the filters in their place 5 Close the front grille ENGLISH
11. andHumidiyRanges 24 m Operating Your Air Conditioner Without the Remote Control 25 m Troubleshooting Guide 26 m Cleaning Your Air Conditioner 27 m Cleaning Anti Allergy and Deodorizing Filter Option 27 Correct Disposal of This Product Waste Electrical amp Electronic Equipment Applicable in the European Union and other European countries with separate collection systems This marking shown on the product or its literature indicates that it should not be disposed with other household wastes at the end of its working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take this item for environmentally safe recycling Business users should contact their supplier and check the terms and conditions of the purchase contract This product should not be mixed with other commercial wastes for disposal ENGLISH Name of Each Part The design and shape can be changed according to the model Air Inlet Room Temperature sensor Power On Off button i Air
12. ases continuously and turns round each time you press the button 4 To control the airflow direction refer to page 19 ENGLISH Mode Digital 7 On Off O J Selecting the Turbo Function You can select the Turbo Function if you want to cool or heat your room in the fastest way After the 30 minute operation with the maximum setting it returns to the previous setting 1 If necessary press the On Off button Result 4 The operation indicator on the indoor unit lights up 4 The air conditioner starts up in the mode you selected last The indoor unit beeps O Mode Digital 7 On Off O O 2 Press the button Result o The temperature and fan settings are adjusted automatically The fan speed indicator turns round with the maximum setting and speed The air conditioner cools or heats the room as quickly as possible After 30 minutes the air conditioner is reset automatically to the previous setting You can select the Turbo function in the Auto Cool and Heat mode e If you select this function in the Dry or Fan mode the mode Sy changes to the Auto mode E i CO o 3 Press the QO button again to stop the Turbo Function before the end of the Control Panel 30 minute period Result The air conditioner is reset automatically to the previous setting as
13. ax current is measured according to IEC standard for safety 4 Current is measured according to ISO standard for energy efficiency Contents PREPARATION m Safety Precautions 2 m Name ot Each Pat eerst ieri ra BAE ve eaters 4 m Remote Control Buttons and Display 6 m Inserting the Remote Control Batteries 7 m Getting Start 0 11 8 4 OPERATION m Selecting the Auto Mode 9 mSelectngtiheCoolMode 10 mSelectngtiheHeatMode 11 mSelecingiheDyMode 12 m Selecting the Fan Mode 13 mSelectingthelurboFunction 14 m Selecting the Energy Saving Function 15 m Selecting the Auto Cleaning Function 16 m SelectingtheSoundOn OffFunction 17 mSelectingtheAnionsFuncton 18 m Adjusting the Airflow Direction Vertically 19 m Adjusting the Airflow Direction Horizontally 19 mSetingiheOnTimer 20 m Setting the Off Timer 21 mSetingiheSleeplimer 22 RECOMMENDATIONS FOR USE m Operating Recommendations 23 mlemperaturec
14. filter Airflow blades under the grille outlet Set temperature amp room temperature Operation indicator Auto Cool Cool Dry Fan Blue E Auto cleaning indicator Auto Heat Heat Orange Blue Turbo function indicator e Da Energy saving indicator Blue Blue Anions indicator Orange Blue Fan speed indicator Blue Timer a dD LA Shy Remote control sensor a Note 4 In the Auto mode 2 fan indicators increase and decrease continuously and turn round 4 In the modes except the Auto mode the fan speed indicator increases and decreases continuously and turn round each time you press the gt 3 button If you set the Turbo function the fan speed indicator turns hy round with the maximum setting and speed If you want to turn on off the Display during operation Digital i On Off press the 3 button on the remote control 4 The room temperature sensor senses air temperature around the sensor and shows the temperature on the display a Out Unit ASO9BPAX ASO9BPBX AS12BPAX ASI2BPBX Air Inlet Rear Air Outlet Connection Valve inside Oda Unit AS18BPAX AS18BPBX Air Inlet Rear Air Outlet Connection Valve BEGG Unit AS24BPAX AS24BPBX Air Inlet Rear Air Outlet Connection Valve ENGLISH Remote Control Buttons and Display Remote control transmission indicator Battery life indicator Fan speed indicato
15. mation about your air conditioner Please read this manual carefully before using the air conditioner It will help you take full advantage of the unit s features You have already seen the basic description of the unit on pages from 4 to 6 Starting with the next page you will find a series of step by step procedures for each function available The illustrations in the step by step procedures use three different symbols HOLD DOWN Selecting the Auto Mode ENGLISH You can select the Auto mode if you want to cool or heat your room automatically You can adjust the temperature in this mode 1 If necessary press the On Off button Result o The operation indicator on the indoor unit lights up The air conditioner starts up in the mode you selected last The indoor unit beeps O O Mode Digital On Off 2 Press the O button on the remote control until Za is displayed O Cc Result 4 The indoor unit beeps each time you press the button The air conditioner runs in the Auto mode The Auto mode cools or heats the room depending on the set temperature The air conditioner changes the Cool or Heat mode automatically depending on the current temperature during operation Note You can change modes at any time 3 Press the OLO button to adjust the temperature until the required temperature is displayed You can set the temperature between 16 C and 30
16. nter directly Never spill any kind of liquid on the air conditioner If this happens turn off the air conditioner and contact an authorized service center 4 Do not insert anything between the airflow blades to prevent damage of the inner fan and consequent injury Keep children away from the air conditioner Do not place any obstacles in front of the air conditioner 4 Do not spray any kind of liquid into the indoor unit If this happens turn off the air conditioner and contact a service center Make sure that the air conditioner is well ventilated at all times Do not place a cloth or other materials over it 4 Remove the batteries if you don t use the remote control for a long time If applicable Use the remote control within 7 meters from the indoor unit If applicable DISPOSING OF THE UNIT Before throwing out the air conditioner remove the batteries from the M remote control When you dispose of the air conditioner consult your dealer If pipes are removed incorrectly refrigerant may blow out and cause air pollution When it contacts with your skin it can cause skin injury 4 The package of the air conditioner should be recycled or disposed of properly for environmental reasons OTHERS Never store or load the air conditioner upside down or sideways to EEE prevent the damage to the compressor Young children or infirm persons should be always supervised when they use the air conditioner M
17. ow Note You can set Sleep Timer only in the Cool or Heat mode Cooling The set temperature is increased by 1 C every hour After the increase of 2 C the temperature is maintained Set for 4 hours TEMP hr 2hr 6hr Start Stop time time Heating The set temperature is di i o a op decreased by 1 C every hour time limo After the decrease of 2 C the set thr_2hr 6hr temperature is maintained TEMP for 4 hours i To Cancel the Sleep Timer Press the 4 button to cancel the Sleep Timer Result The indoor unit beeps 4 The 2 indicator is no longer displayed 4 The air conditioner operates normally Es Operating Recommendations ENGLISH When you use your air conditioner it is recommended to read the following Topic Recommendation Heating capacity The heat pump inside the air conditioner absorbs heat from outside air and brings it indoors If the temperature of the outside air drops the air conditioner heats less If the room is not warm enough use an additional heating appliance Warm air circulation The air conditioner circulates warm air to heat your room It will take some time to warm the air in your room entirely after the air conditioner turns on Therefore turn the air conditioner on in advance Frost When you select the Heat mode frost may form in the outdoor unit due to the low temperature and high humidity If this happens
18. r Anions indicator Sleep mode indicator On Timer indicator Power On Off button Mode selection button AUTO COOL DRY FAN HEAT Fan speed adjustment button Turbo button Energy saving button On Timer button Off Timer button A so Dr ss dr l Mode Digital On Off o A eo AAA Operating mode L AUTO H COOL f DRY c amp FAN 20 HEAT Sound On Off indicator Turbo function indicator Temperature setting Air flow direction Off Timer indicator Energy saving indicator Temperature adjustment buttons Digital On Off button Swing button Sound On Off button Auto Cleaning button Timer Set Cancel button Sleep button Anions button Inserting the Remote Control Batteries ENGLISH You must insert or replace the remote control batteries when You purchase the air conditioner The remote control does not work correctly Note Use two AAA LRO3 1 5V batteries Do not use old batteries or different kinds of batteries together Batteries may be completely discharged after 12 months even if they have not actually been used 1 Remove the battery cover in the rear of the remote control by pushing it with your thumb 2 nsert two batteries respecting the polarities as indicated by the and symbols 3 Close the cover by sliding it back in its place Getting Start The User s Manual provides you with valuable infor
19. rol 299 Check if the circuit breaker of the air conditioner is switched on Check if the air conditioner is turned on If necessary press the On Off button on the remote control Check if the Timer indicator on the indoor unit is on If so Wait until the set time is reached and the air conditioner starts automatically Cancel the Timer See pages 20 and 21 for further details Check if there are no obstacles in front of the indoor unit Check the remote control batteries Make sure that you are within 7 meters from the indoor unit No beep is heard when you press the On Off button on the remote control Check if you are pointing the remote control at the remote control sensor on the right side of the indoor unit Replace the remote control batteries if necessary The air conditioner does not cool or heat 2099 Check if the correct operating mode has been selected Auto Cool Heat The room temperature may be too low or too high Check if the air filter is dirty refer to page 27 for cleaning instructions Check that there is no obstacle in front of the outdoor unit When heating the required room temperature is never reached and the air conditioner frequently stops 299 Check if the required temperature is set correctly Increase the fan speed If the airflow is directed upwards set the blade downwards with the remote control The fan speed does not change
20. rs 1 Tamer Press the button until the required time is displayed to set the Off Timer You can set the time between 0 5 hour and 24 hours Taa gt mye m5 2 Pressthe button to complete the setting Result 4 The remaining time is displayed The timer indicator stops blinking The air conditioner turns off automatically at the appointed N A 1 time and the Off Timer setting disappears Ga m i gt Example If you would like to turn the air conditioner on after 2 hours and to epee it for 2 hours 1 Press the 5 button until 2 0 Hr is displayed 2 Press the 55 Es button 3 Press the pes button until 4 0 Hr is displayed 4 Press the Es button Note You can check or change the mode and or the temperature by pressing the button or the sG button after setting the Off Timer To Cancel the Off Timer Note If you press the se button both the On Timer and the Off Timer Press the A button to cancel the Off Timer are canceled Setting the Sleep Timer You can set the Sleep Timer to turn off the air conditioner automatically while you are sleeping The air conditioner stops operating 6 hours after you set the Sleep Timer D SE 1 Pressthe button a jj Sayi gt Result The indoor unit beeps m 4 The air conditioner will be controlled as indicated in the illustrations bel
21. u want to sterilize the air conditioner or remove mold Even when the air conditioner is turned off you can set this function 1 If necessary press the On Off button Result 4 The operation indicator on the indoor unit lights up 4 The air conditioner starts up in the mode you selected last j The indoor unit beeps O 2 Press the Sa button 0 Mode Digital on off Result Oo 4 The Es indicator on the indoor unit lights up and the O Auto Cleaning function is set _ When you turn the air conditioner off it operates the Auto Cleaning function for 30 minutes Remote Control After 30 minutes the air conditioner turns off If you press the S button when the air conditioner is Djl Y A turned off the air conditioner operates the Auto Cleaning lt a 24 gt Function for 30 minutes When the air conditioner ln gt is turned Mode Operating time On Auto Cool Dry 30 minutes Heat Fan 15 minutes Off 30 minutes Control Panel Note The Auto Cleaning indicator is displayed only on the indoor unit A E m Vem 3 Press the button again to stop the Auto cleaning function before cn the end of the 30 minute period gt y Selecting the Sound On Off Function ENGLISH You can turn on or off the sound of the air conditioner with the remote control 1 Pressthe e button to turn off the sound Mote Each time you press the e button Sound On Off function is
22. when you press the amp button Check if the mode is set to the Cool Heat or Fan mode in the Auto and Dry mode the fan speed changes automatically The airflow direction does not change when you press the ce button Check if the air conditioner has been turned on if necessary press the On Off button on the remote control The timer is not correctly triggered Check if the timer is set correctly see pages 20 and 21 Odor permeates into the room during operation You can use the Fan mode to ventilate your room Cleaning Your Air Conditioner For the best use of your air conditioner you must clean it every 2 weeks to remove the dust that accumulates on the air filter PORTANT Before cleaning your air conditioner check if you have turned off the circuit breaker 1 Open the front grille by pulling on the tabs on the lower right and left sides of the indoor unit 2 Detach the front grille by pulling it forwards 3 Hold the edge of the air filter under the front grille and pull to release 4 Remove all dust on the air filter with a vacuum cleaner or brush 5 When you finish insert the top of the filter into the slot and fix it to 5 tabs of the grille 6 Clean the front grille with a damp cloth and mild detergent do NOT use benzene solvents or other chemicals 7 Reassemble the air filter and the front grille Note If you have not used the air conditioner for
23. y y 4 To control the airflow direction refer to page 19 Selecting the Energy Saving Function ENGLISH You can select the Energy Saving Function to save energy when cooling The temperature range decreases in order to perform this function 1 If necessary press the On Off button Result o The operation indicator on the indoor unit lights up The air conditioner starts up in the mode you selected last The indoor unit beeps Mode Digital 7 On Off t OO 2 Press the Es button Result 4 The indoor unit beeps 4 The air conditioner runs in the Energy saving function The outer airflow blade moves up and down To stop the Energy saving function press the A again Note You can select the Energy saving function only in the Cool mode 3 Press the QIO button to adjust the temperature until the required temperature is displayed You can set the temperature between 26 C and 30 C Mote If you want to adjust temperature under 26 C cancel the Energy saving function before adjusting the temperature 4 Press the E button to select the fan speed until the required setting is displayed Note The fan speed indicator increases and decreases continuously and turns round each time you press the 3 button 5 To control the airflow direction refer to page 19 Selecting the Auto Cleaning Function You can select the Auto Cleaning Function if yo
Download Pdf Manuals
Related Search