Samsung SU2913 User Manual
Contents
1. Replace the door by inserting the tabs on the left side and snapping the right side into place Grasp the Circular Filters and twist to unlock Pull straight up to remove Separate the Outer foam and Inner pleated Circular Filters Wash each individually by hand in warm water Mild detergent may be used if desired Rinse well then air dry Thoroughly dry before putting them back together and replacing in the Filter Cup The Filter Cup may be washed In warm water with a mild detergent Make sure it is completely dry before reassembling with fliters Do not operate cleaner without Either the Pre Motor Filter or Post Motor Filter in place The belt The belt on your cleaner causes the agitator to rotate and is important for the effective operation of the cleaner The belt is located under the bottom plate of the cleaner and should be checked from time to time to be sure it is in good condition When to replace Disconnect cleaner from electrical outlet To check belt remove bottom plate as shown in How to replace Replace belt if it is stretched cut or broken With lettering on outside of belt and positioned as shown in box on D slide new belt over motor pulley B Reposition bottom plate and 5 screws Tighten screws securely Maintenance 3 8 How to replace Disconnect cleaner from electrical outlet Place handle in low position and turn cleaner over so bottom side is up Remove th2. Note All new carpet has loose fibers which can fill the Dirt Cup quickly while vacuuming Emptying the Dirt Cup 3 1 Position Slide the Cyclone Lever to the Unlock position Grasp handle and pull the Dirt Cup straight out to remove from Vacuum Disconnect cleaner from electrical outlet Empty dirt into garbage container Put the Dirt Cup back in the vacuum and slide the lever to the Lock position Cleaning the Pre Post motor Filter Cleaning The Circular Filters Grasp the Filter Cup located at the bottom of the Dirt Cup and twist counterclockwise to unlock and remove How to clean Disconnect cleaner from electrical outlet The Pre Motor Filter protects the Motor from debris It is located underneath the Dirt Cup and Filter Cup in the Center of the round part of the Cyclone Lever Remove the small round Filter and any debris on top of it Rinse well under warm water then air dry thoroughly before replacing The Post Motor Filter assists in the filtration process to return clean air to the room It is located behind the door on the front of the Cleaner When the filter becomes dirty The Micro Filter Open the door remove the filter and shake the dust off the filter The Micro Filter is non washable therefore do not wash it in water The Hepa Filter Select Models Open the door remove the filter and replace The Hepa Filter is not washable and must be replaced
3. use cord as a handle close a door on cord or pull the cord around sharp edges or corners Keep cord away from heated surfaces e Do not unplug by pulling on the cord To unplug grasp the plug not the cord e Do not handle vacuum cleaner or plug with wet hands e Do not put any object into openings Do not use with any opening blocked keep openings free of dust lint hair and anything that may reduce air flow e Keep hair loose clothing fingers and all parts of body away from openings and moving parts e Do not pick up anything that is burning or smoking such as cigarettes matches or hot ashes e Do not use without dirt cup or filters in place Empty dirt cup and clean filter frequently when picking up very fine materials such as powder e Turn off all controls before unplugging vacuum cleaner e Use extra care when cleaning on stairs e Do not use to pick up flammable or combustible materials such as gasoline or fine wood fine wood sandings or use in areas where they may be present e Store your vacuum cleaner indoors in a cool and dry area e Avoid picking up hard sharp objects with the cleaner They may damage the cleaner e Always turn off this appliance before connecting or disconnecting the hose removing the bottom plate for maintenance e Use only on dry indoor surfaces never change the plug in any way e Do not modify the polarized plug to fit a non polarized outlet or extension cord e Do not touch the brush roller
4. carpet or floor For above floor cleaning the floor brush will continue to rotate but is raised above floor To prevent carpet damage do not lean on the vacuum or let the powerfoot tilt forward The assembled cleaner will look like the illustration to the left 1 Handle 2 Power switch 3 Quick release cord hook 4 Post Motor Filter 5 Crevice tool 6 Handle release 7 Carrying handle 8 Hose 9 Extension wand 10 Combination tool 11 Cyclone Lever 12 Dirt Cup 13 Filter Cup 14 Upper Tank 15 Louvers 16 Hose Wand Base 17 Height Adjustment Dial 18 Hose Clip OPERATE THE VACUUM CLEANER ONLY AT THE VOLTAGE SPECIFIED ON THE NAMEPLATE Step 1 Attaching the Handle Step 2 Attaching the Hose and Tools Aus Stand the vacuum upright and slide the base of the handle firmly into the grooves at the top of the vacuum body A 1 5 aS Insert the screw provided into the Slide the end of the hose Slide the extension wand existing hole Tighten the screw wand with tabs into the Hose and the crevice tool together securely with a screwdriver Wand Base into the storage clip Before securing the handle please check that the handle is fitted to the vacuum body and make sure there s no gap Operation ON OFF Switch Handle positions Transporting cleaner 1 To turn cleaner on press the ie handig of your cleaner nag To move your cleaner from room to Power switch AINN nae eaningtools 7 room
5. put the handle in upright operating for general operation on position tilt the cleaner back on its 2 To the cleaner off press the carpet and floors low for reachin rear wheels and push forward Power switch again under low furniture Step on handle release pedal to lower handle f When using the attachments ensure the vacuum cleaner is placed firmly on the floor with the handle in the upright osition Do not place the vacuum on top of umiture or steps as the brushroller may cause damage A Combination tool Two types of cleaning tools ar included in one attachment rotate for desired tool Use brush side to dust fumiture blinds books lamps shelves Use upholstery side for curtains draperies cushions fabrics B Crevice tool Use in comers on stairs baseboards and behind furniture C Extension Wand Use with desired attachments and narrow wand for a longer reach option D Mini Turbo Brush Select Models Use rotating brush action for small areas such as stairs and upholstery Cleaning Tool attachments Note Press gently when using Mini Turbo Carrying handle The cleaner can also be moved by using the carrying handle Attachment tools can be used to Brush to gain maximum cleaning Too much clean furniture or drapes on stairs pressure could cause the brush to stop rotating or in corners E Wooden Floor Brush Select Models Use for bare floors Swivel head turns to get into tigh
6. Vacuum Cleaner SU 2910 Series FOR HOUSEHOLD USE ONLY Operating Instructions IMPORTANT SAFETY INSTRUCTIONS 1 ASSEMBLING PARTS eeessteesseessseesssseeesssesesneeessnese ASSEMBLED VACUUM CLEANER PARTS ATTACHING THE HANDLE ATTACHING THE HOSE AND TOOLS OPERATION sssssisssosscsesiscsosassssasiss MAINTENANCE TROUBLESHOOTING iP ZA R s T 4 Smm 9 4 7 a gt s 4 T i ZI Read these instructions before operating the vacuum cleaner eThe design and specification may be different depending on the models Register your product at www samsung com register IMPORTANT SAFETY INSTRUCTIONS Thank you for purchasing a Samsung vacuum cleaner When using an electrical appliance basic precautions should always be followed including the following PLEASE READ ALL WARNINGS AND INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER WARNING To reduce the risk of fire electric shock or injury e Do not leave vacuum cleaner unattended when it is plugged in e Unplug from outlet when not in use and before servicing e Do not use outdoors or on wet surfaces e Use only as described in this manual Use only manufacturer s recommended attachments e If vacuum cleaner is not working as it should or has been dropped damaged left outdoors or dropped into water return it to a service center e Do not pull or carry by cord
7. ainers pointing down slide e Cut off pet hairs or threads remove retainers into grooves in tool surrounding brush by using Remove belt from turbine pulley housing and snap into place scissors Replace with new belt Replace brushbar and bottom plate THis Vacuum cleaner is approved the following Electromagnetic Compatibility Directive 2004 108 EEC Low Voltage Directive 2006 95 EC If you have any comments or questions regarding a Samsung products contact the SAMSUNG customer care center Country Customer Care Center T Web Site U K 0845 7267864 SAMSUNG www samsung com uk SOUTH AFRICA 0860 7267864 SAMSUNG www samsung com za DJ68 00294L REV 0 5
8. e 5 screws as shown with a screw driver r CZ 3 1 0 a A N Insert agitator through belt and place belt in belt guide C on agitator Should the agitator shield D become dislodged while replacing the belt or the agitator reposition it as shown noting the placement of its belt guide E When to replace the agitator brush roll When agitator brushes are worn the agitator should be replaced To check condition of brushes disconnect cleaner from electrical outlet Move the edge of a card across bottom plate while turning agitator To maintain cleaning effectiveness replace agitator if brushes do not touch card Remove agitator and used belt Discard used belt Grasp agitator firmly and fit it into position by first sliding the end opposite the belt into the rectangular slot F on side of cleaner Pull other side of agitator G into place Turn agitator making sure belt is not pinched between agitator and agitator shield How to replace Disconnect cleaner from electrical outlet Remove bottom plate belt and agitator following directions in The belt section beginning with Fig 3 10 Discard old agitator Continue following the directions in The belt section to reposition belt new agitator and bottom plate Maintenance Clearing Blockages Disconnect cleaner from electrical outlet The hose on the back of the vacuum cleaner that carries the dirt from the nozzle to the Dirt C
9. o lower setting Problem Poor job of dirt pickup Possible Cause Possible Solution Full or clogged Dirt Cup Empty the Dirt Cup and check for blockages Broken or worn belt Replace belt Clogged hose or nozzle Clean hose or nozzle area Hole in hose Replace hose Dirt Cup improperly installed Properly install the Dirt Cup Incorrect carpet height setting Rotate nozzle control knob to lower setting Clogs in air flow passage Clear clogs clean filters as per manual instructions Problem Abnormal sound Possible Cause Possible Solution Strange sound like rushing air Check for clogs in hose nozzle area and or filters clear or claen any clogs or blockages as per manual instructions Mini Turbo Brush Option Use for upholstered furniture carpeted stairs and hard to reach places Brush bar Replacement With the curved ends facing Remove the tool from the hose And remove brushbar and down slide end plates of and turn upside down Slide the discard brushbar into slots on the tool switch to unlock position Inspect belt to ensure that it is in To replace bottom plate insert good condition If broken or the four tabs on edge of cracked please replace See bottom plate into slots on front below for details of tool Pivot bottom plate down and snap closed ent With flat sides of turbine Cleaning Brushbar Grasp turbine and pull firmly to ret
10. t spaces and fits under cabinets Note The Wooden Floor Brush does not store on board Carpet height adjustment Carpet and rug cleaning takes place at the nozzle A When it is necessary to raise and lower the nozzle for various carpet pile heights rotate the nozzle control dial B to the desired setting Cleaning lightweight flexible rugs Stand on one end of rug and move cleaner toward other end or edge Before reaching edge push down on handle This will lift up the nozzle front of Cleaner and will prevent rug from clinging to cleaner Continue to lift front of cleaner so that when you have reached the edge it is completely off the rug Move cleaner back to start again lower front of cleaner and use only forward strokes For maximum cleaning performance The following carpet height settings are recommended Lowest setting for all types of carpet Higher settings for very deep pile carpet where easier pushing effort is desired while maintaining good cleaning performance Note If the cleaner is difficult to push rotate knob to the next higher setting Maintenance Familiarize yourself with these home maintenance tasks as proper use and care of your cleaner will ensure continued cleaning effectiveness When to empty the Dirt Cup The dirt cup needs to be emptied when the dirt reaches the MAX line on the side of the Cup If more dirt than this accumulates your cleaner will not operate effectively
11. up can sometimes become clogged If you notice a change in the sound of the vacuum motor check for blockages Remove the Hose and disconnect If the blockage persists turn the Tank and Louvers the Wand vacuum cleaner off and unplug it Check to make sure Louvers are Check for clogs in the vacuum Remove the bottom plate Lift up Installed correctly To unlock the base the wand the hose and the the short hose in the base of the Louvers grasp the rim and turn suction inlet vacuum Inspect the hose for clogs Toward the left Pull straight down to remove If the Louvers are missing or not locked into place check and clear the tube in the center of the Dirt Cup and remove any obstructions Replace the short nozzle hose and the bottom plate Troubleshooting Check this list of possible problems and solutions before bringing your vacuum to a service center Problem Cleaner won t run Possible Cause Possible Solution Not firmly plugged in Plug unit in firmly No voltage in wall plug Check fuse or breaker Blown fuse or tripped breaker Replace fuse or reset breaker Filters blocked or dirty Clean filters as per manual instructions Problem Dust escapes the Dirt Cup Possible Cause Possible Solution Dirt Cup improperly installed Re install the Dirt Cup Problem Cleaner hard to push Possible Cause Possible Solution Incorrect carpet height setting Rotate nozzle control knob t
12. when it is rotating e Keep suction away from your face when using nozzles and pipe e Do not pull the power cord around sharp corners and do not allow it to be trapped e Unplug before connecting turbine nozzle only using turbine brush model e This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety e Children should be supervised to ensure that they do not play with the appliance e The plug must be removed from the socket outlet before cleaning or maintaining the appliance e If the supply cord is damaged it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard SAVE THESE INSTRUCTIONS This vacuum cleaner is intended for household use only FOR RESIDENTS OF THE UNITED KINGDOM ONLY If your appliance is fitted with a nonrewireable BS 1363 plug it must not be used unless a 13 amp ASTA approved to BS 1362 fuse is fitted in the carrier contained in the plug If for any reason the plug is cut off it must be disposed of as it is an electric shock hazard should it be inserted into a 13 amp socket CAUTION WARNING Assembling Parts Unless power switch is off or unplugged the floor brush will rotate while you use your vacuum cleaner on
Download Pdf Manuals
Related Search