Samsung SC05ZZ8X Инструкция по использованию
Contents
1. Energy Saving Energy Saving 9 A Setting the Sleep Timer The Sleep Timer can be used when you are cooling your room to switch the air conditioner off automatically after a period of 6 hours Note If you wish to switch the unit off at a specific time refer to page 17 1 Make sure that you have selected COOL mode Les JE E ge SET TEMP o C Ld B 2 Pressthe button one or more times until X appears on the remote control Result 4 The indoor unit beeps The air conditioner will be controlled as indicated in the illustrations below Cooling The desired temperature is increased by 1 C every hour When it has been increased by 2 C after 2 hours the temperature is maintained for four hours Start Stop time time To Cancel the Sleep Timer If you no longer wish to use the Sleep Timer that you have set you can cancel it at any time Press the button Result The indoor unit beeps The Jis no longer displayed The air conditioner operates normally Operating Recommendations Here are a few recommendations that you should follow when using your air conditioner Topic Recommendation Power failure If a power failure occurs when the air conditioner is operating the unit is switched off When the power returns the ai2. amm OWNER S INSTRUCTIONS Indoor unit Outdoor unit C05ZZ8 C05ZZ8X Split type Room Air Conditioner f DB98 16005A 1 Safety Precautions The following safety precautions must be taken when using your air conditioner N WARNING DURING OPERATION DISPOSING OF THE UNIT OTHERS Risk of electric shock e Can cause injury or death e Disconnect all remote electric power supplies before servicing installing or cleaning This must be done by the manufacturer or its service agent or a similar qualified person in order to avoid a hazard Users of this product are cautioned not to attempt repair of this product at their own discretion Instead they are requested to directly contact a designated service center or the outlet at which the product was purchased Never spill any kind of liquid into the unit Should this happen unplug or main switch off the unit and contact an authorized service center Do not insert anything between the air outlet blades because the inner fan may be damaged and could cause injury Keep children away from the unit Do not place any obstacles in front of the unit Do not spray liquid of any kind into the indoor unit Should this happen switch off the breaker used for your air conditioner and contact your installation specialist Make sure that the unit is correctly ventilated at all times Do not place clothing or other materials over it If the wireless remote control will n
3. conditioner before the timer reaches the setting time press the On Off button Setting the Off Timer The Off Timer enables you to switch off the air conditioner automatically after a given period of time You can set the period of time from 30 minutes to 24 hours 1 To setthe operating time press the button one or more times until the required time is displayed Possible time is between 0 5 hour and 24 hours inclusive 2 Press the Set Cancel button to complete the setting Result The remaining time is displayed Blinking of the timer indicator stops The air conditioner will switch off automatically when the counter displayed on the remote control reaches the set time and disappears the Off timer setting Example If you would like to turn the air conditioner on after 2 hours and to operate it for 2 hours 1 Press the button until 2 0 Hr is displayed 2 Press the Set Cancel button 3 Press the button until 4 0 Hr is displayed 4 Press the Set Cancel button Note You can see or change the setting mode and or the temperature by pressing the button or the S button after setting the Off timer To Cancel the Off Timer 1 To cancel the Off Timer press the button one or more times until the timer setting disappears 2 Press the Set Cancel button Note If you want to turn off the air conditioner before the timer reaches the setting time press the amp On Off button
4. it is started immediately after being Plugged in Stopped It will start up normally after three minutes 2 Ifthe e is not displayed at the top of the remote control press the button on the remote control one or more times until it appears Result The indoor unit beeps each time you press the button The air conditioner runs in DRY mode Note You can change modes at any time 3 To adjust the temperature press the button one or more times until the required temperature is displayed Possible temperatures are between 18 C and 30 C inclusive Result 4 Each time you press the putton The temperature is adjusted by 1 C The indoor unit beeps The air conditioner starts removing the excess humidity the quantity of air is adjusted automatically 4 To control the direction of the air flow refer to page 15 Airing Your Room If the atmosphere in your room is stale you can air the room using the Fan feature 1 If necessary press the On Off button Result The operation indicator on the indoor unit lights up The air conditioner starts up in the mode selected when the unit was last used The indoor unit beeps Energy Saving 2 Ifthe of is not displayed at the top of the remote control press the button on the remote control one or more times until it appears Result The indoor unit beeps each time you press the button The air conditioner runs in FAN
5. mode The temperature is set automatically Note You can change modes at any time 3 Select the fan speed by pressing the C button one or more times until the required setting is displayed E Low Tu Medium Sul High Result Each time you press the button the indoor unit beeps 4 To control the direction of the air flow refer to page 15 Selecting Energy Saving Mode If you wish to save energy when using your air conditioner select the Energy saving mode with the Energy Saving button 1 If necessary press the On Off button Result The operation indicator on the indoor unit lights up The air conditioner starts up in the mode selected Gite when the unit was last used Off Timer The indoor unit beeps PORTANT The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being Plugged in Stopped It will start up normally after three minutes 2 Select COOL mode by pressing the button Note You can select the Energy saving mode only in COOL mode 3 Press the CS button Result The indoor unit beeps The air conditioner runs in the Energy saving mode The outer air flow blade moves up and down To stop the Energy saving mode press the CS again 4 To adjust the temperature press the D button one or more times until the required temp
6. O COOL The room temperature may be too low Dust may be blocking the air filter guard refer to page 23 for cleaning instructions Check that there is no obstacle in front of the outdoor unit The fan speed does not change when you press the button Check that the operating mode is set to COOL or FAN in the AUTO mode the fan speed changes automatically and in the DRY mode it is set to AUTO The air flow direction does not change when you press the button The timer is not correctly triggered Check that the air conditioner has been switched on if necessary press the On Off button on the remote control Check that the timer has been programmed correctly see pages 16 and 17 Odour is permeated in the room during air conditioning Air the room Cleaning Your Air Conditioner To get the best possible use out of your air conditioner you must clean it regularly to remove the dust that accumulates on the air filter PORTANT Before cleaning your air conditioner ensure that you have switched off the breaker used for the unit 1 Press the right and left marks of the front grille pushing it 2 Remove the front grille from the indoor unit to remove the air filter 3 Remove all dust on the air filter with a vacuum cleaner or brush 4 When you have finished insert the filter into the grille 5 Ins
7. an be adjusted horizontally 1 Adjust each set of inner blades to the required position by pushing or pulling them sideways Setting the On Timer Energy Saving eo Energy Saving gt E 5 e Off Timer The On Timer enables you to switch on the air conditioner automatically after a given period of time You can set the period of time from 30 minutes to 24 hours 1 To set the operating time press the button one or more times until the required time is displayed Possible time is between 0 5 hour and 24 hours inclusive Press the 59 Set Cancel button to complete the setting Result The remaining time is displayed Blinking of the timer indicator stops The selected mode and the temperature on the display disappear after 10 seconds The air conditioner will switch on automatically when the counter displayed on the remote control reaches the set time and disappears the On timer setting To select an operating mode in advance press the button until the desired mode is displayed at the top of the remote control Result The air conditioner will run in the selected mode when it is turned on To Cancel the On Timer 1 To cancel the On Timer press the button one or more times until the timer setting disappears 2 Pressthe Set Cancel button Note Ifyou want to turn on the air
8. e control EP transmission indicator porte ode Mode selection button Operating mode AUTO COOL DRY FAN amp AUTO COOL C DRY f amp FAN Temperature setting Temperature adjustment buttons Turbo mode Tarbo Turbo Sl d i apl urbo Sleep mode Sleep mode Selection button Energy saving Fan speed adjustment button Fan speed Air flow direction Swing button On Timer setting 2 3 On Timer button Off Timer setting 7 3 Off Timer button Battery discharge indicator 3 34 On Off amp Energy Saving button Timer Set Cancel button Getting Started You have just purchased a split type air conditioner and it has been installed by your installation specialist Your Owner s Instructions contains valuable information on using your air conditioner Please take the time to read it as it will help you take full advantage of the unit s features The booklet is organized as follows The following figures are shown on pages from 4 to 6 Indoor and outdoor units Remote control buttons and display They will help you find the buttons and understand the symbols displayed Inthe manual you will find a series of step by step procedures for each function available The illustrations in the step by step procedures use three different symbols HOLD DOWN Inserting the Remote Control Batteries You must insert or replace the remote control batteries wh
9. en You purchase the air conditioner The remote control does not work correctly Note Use two AAA LR03 1 5V batteries Do not use old batteries or different kinds of batteries together Batteries may be completely discharged after 12 months even if they have not actually been used 1 Push the battery cover on the rear of the remote control with your thumb in the direction of the arrow and remove it 2 Insert the two batteries taking care to respect the polarities on the battery with on the remote control on the battery with on the remote control 3 Close the cover by sliding it back until it clicks into place Selecting the Automatic Operating Mode You can start the air conditioner in Automatic mode from your remote control In the Automatic mode the standard temperature and the optimum fan speed is selected automatically You can adjust the standard temperature but not the fan speed 1 If necessary press the On Off button Result The operation indicator on the indoor unit lights up The air conditioner starts up in the mode selected when the unit was last used The indoor unit beeps PORTANT The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being Plugged in Stopped It will start up normally after three minutes 2 Ifthe C is not displayed at the top of the remote control press
10. eps each time you press the button The air conditioner runs in COOL mode Note You can change modes at any time To adjust the temperature press the button one or more times until the required temperature is displayed Possible temperatures are between 18 C and 30 C inclusive Result Each time you press the A button The temperature is adjusted by 1 C The indoor unit beeps The air conditioner starts cooling provided that the room temperature is higher than the selected temperature If the room temperature reaches the set temperature the air conditioner stops cooling but the fan is still operating Select the fan speed by pressing the button one or more times until the required setting is displayed Automatic rotated fu Far gt Sul DAP Low ean Medium s n High Result Each time you press the button the indoor unit beeps To control the direction of the air flow refer to page 15 Changing the Room Temperature Quickly The Turbo cooling function is used to cool your room as quickly as possible Example You have just come home and find that the room is very hot You wish to cool it down as quickly as possible The Turbo function operates for 30 minutes with the maximum settings before returning automatically to the mode and temperature previously selected 1 If necessary press the onion button jeep Mode Result The ope
11. erature is displayed Possible temperatures are between 26 C and 30 C inclusive Note If you want to adjust temperature under 26 C cancel the Energy saving mode before adjusting the temperature 5 To select the fan speed press the button one or more times until the required setting is displayed 6 To control the direction of the air flow refer to page 15 Adjusting the Air Flow Direction Vertically Depending on the position of the indoor unit on the wall of your room you can adjust the position of the outer air flow blade on the bottom of the unit thus increasing the efficiency of the air conditioner 1 Press the button one or more times as required Result The outer blade is adjusted vertically RECOMMENDATION When Adjust the blade to face Cooling Upwards 2 If you want the blade to move up and down automatically when the air conditioner is operating press the button Result The blade moves up and down around the base position set 3 To stop the blade moving up and down press the button again Note Ifyou switch the air conditioner Then the blade is Off Closed completely On again Set to the initial position powered OGD eS a fo S Iz 3 E 5 B B RJ X Adjusting the Air Flow Direction Horizontally There are two sets of inner air flow blades Just as the outer air flow blade can be adjusted vertically the inner blades c
12. ert the top part of the front grille into their slots and push down on the bottom slots until they click into place 6 Clean the front grille with a damp cloth and mild detergent do NOT use benzene solvents or other chemicals Note If you have not used the air conditioner for a long period of time set the fan going for three to four hours to dry the inside of the air conditioner thoroughly THIS AIR CONDITIONER IS MANUFACTURED BY lt a ELECTRONICS
13. ot be used for a long time remove the batteries If applicable When using a wireless remote control the distance should not be more than 7 meters from the air conditioner If applicable Before throwing out the device it is necessary to pull back the battery cells and get rid of them safely for recycling reasons When you need to dispose of the unit consult your dealer If pipes are removed incorrectly refrigerant may blow out and come into contact with your skin causing injury Releasing refrigerant into the atmosphere also damages the environments Please recycle or dispose of the packaging material for this product in an environmentally responsible manner Never store or ship the air conditioner upside down or sideways to avoid damage to the compressor The appliance is not intended for use by young children or infirm persons without supervision Young children should be supervised to ensure that they do not play with the appliance Max current is measured according to IEC standard for safety and current is measured according to ISO standard for energy efficiency Contents PREPARING YOUR AIR CONDITIONER m Safety Precautions 00 cece eee eee 2 n View orthe Units sei eax ode dus ee qo od e HE UE ete aes 4 m Remote Control Buttons and Display 6 m Getting Started 4 7 m Inserting the Remote Control Batteries 8 OPERATING YOUR AIR CONDITIONER m Selecting the Automatic Ope
14. r conditioner starts up again automatically Temperature and Humidity Ranges The following table indicates the temperature and humidity ranges within which the air conditioner can be used If the air conditioner is used at Then High temperatures The automatic protection feature may be triggered and the air conditioner stopped Low temperatures A water leak or some other malfunction may occur if the heat exchanger freezes High humidity levels Water may condense on and drip from the surface of the indoor unit if it is used for long periods Mode Outdoor Temperature Indoor Temperature Indoor Humidity Cooling 21 C to 43 C approx 18 C to 32 C approx 80 or less Drying 18 C to 43 C approx 18 C to 32 C approx Me x Ifthe cooling operation is used at over 33 C indoor temperature it does not cool at its full capacity Operating Your Air Conditioner Without the Remote Control Your air conditioner can be operated directly from the indoor unit if the remote control is lost or broken 1 To turn the air conditioner on press the On Off button on the right side aemm of the indoor unit Result The Operation indicator on the indoor unit comes on The indoor unit beeps JOAN P The air conditioner starts up in the most suitable mode for z the room temperature Room Temperature Operating Mode Temperature Setting 21 C or above Cool 24 C approx 2 To turn the air conditioner off pre
15. rating Mode 9 m Cooling Your ROOM e ene dde oer ved 10 m Changing the Room Temperature Quickly 11 m Removing Excess Humidity 0 0 cece eee eee 12 N Your ROOM auis er experte mer annie tuom Rer ae bg 13 m Selecting Energy Saving Mode 0000 14 m Adjusting the Air Flow Direction Vertically 15 m Adjusting the Air Flow Direction Horizontally 15 PROGRAMMING YOUR AIR CONDITIONER m Setting the On Timer 00 cece eee 16 m Setting the Off Timer 20 ieie etapa 17 m Setting the Sleep Timer 0 an 18 RECOMMENDATIONS FOR USE m Operating Recommendations 000 19 m Temperature and Humidity Ranges 00000 20 m Operating Your Air Conditioner Without the Remote Control 21 m Solving Common Problems 4 22 m Cleaning Your Air Conditioner 00 0 23 View of the Unit The design and shape are subject to change according to the model Air filter under the grille Air Inlet Air flow blades outlet Operation indicator Remote Control Sensor Green On Off button Turbo indicator Green Timer indicator Orange Outdoor Unit Air Inlet Rear Air Outlet Connection Valve inside Remote Control Buttons and Display Remot
16. ration indicator on the indoor unit lights up B The air conditioner starts up in the mode selected when the unit lt A gt v was last used V3 The indoor unit beeps TURBO full 2 Press the button Result The temperature and fan settings are adjusted automatically The air conditioner cools the room as quickly as possible After 30 minutes the air conditioner is reset automatically to the previous mode temperature and fan settings But if you press the button in DRY or FAN mode it will change to AUTO mode automatically 3 If you wish to stop the Turbo function before the end of the 30 minute period press the button one or more times until or 2 disappears Result The air conditioner is reset automatically to the previous mode temperature and fan settings 4 To control the direction of the air flow refer to page 15 Removing Excess Humidity ss If the atmosphere in your room is very humid or damp you can remove excess humidity without lowering the room temperature too much 1 If necessary press the On Off button Result The operation indicator on the indoor unit lights up The air conditioner starts up in the mode selected when the unit was last used The indoor unit beeps portant The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when
17. ss the On Off button again Note Even if the air conditioner has been turned on via the On Off button operations can still be controlled using the remote control as usual Solving Common Problems Before contacting the after sales service perform the following simple checks They may save you the time and expense of an unnecessary call Problem Explanation Solution The air conditioner does not operate at all Check that the breaker used for the air conditioner is switched on Check that the operation indicator on the indoor unit is on if necessary press the On Off button on the remote control Check whether the Timer indicator on the indoor unit is switched on If so Wait until the switch on time is reached and the air conditioner starts up automatically Cancel the timer see pages 16 and 17 for further details The air conditioner does not operate with the remote control eo Check that there are no obstacles between you and the indoor unit Check the remote control batteries Check that you are close enough to the indoor unit seven meters yards or less No beep is heard when you press the On Off on the remote control Check that you are pointing the remote control at the remote control sensor in the right of the indoor unit Replace the remote control batteries if necessary The air conditioner does not cool Check that the correct operating mode has been selected AUT
18. the button on the remote control one or more times until it appears Result The indoor unit beeps each time you press the button The air conditioner runs in AUTO mode ote You can change modes at any time 3 To adjust the standard temperature The air conditioner automatically set the standard temperature by the current room temperature press the button one or more times V SET TEMP SET TEMP SET TEMP SET TEMP 2 C 1 C Standard temperature 1 C 2 C lt When you feel hot gt lt When you feel chilly gt e Energy Saving Cooling Your Room Energy Saving You must select the Cool mode if you wish to adjust the Cooling temperature Fan speed when cooling 1 If necessary press the On Off button Result The operation indicator on the indoor unit lights up The air conditioner starts up in the mode selected when the unit was last used The indoor unit beeps PORTANT The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being Plugged in Stopped It will start up normally after three minutes 2 Ifthe Es is not displayed at the top of the remote control press the button on the remote control one or more times until it appears Result The indoor unit be
Download Pdf Manuals
Related Search