CANfigurator User Guide
Contents
1. Click Install to continue with the installation or cick Back if you want to review or change any settings Destination location C Program Files x86 CANfigurator Additional tasks Additional icons Create a desktop icon 4 Progress of the installation process H Setup CANfigurator Setup is now ready to begin installing CANfigurator on your computer Click Install to continue with the installation or click Back if you want to review or change any settings Destination location C Program Files x86 CANfigurator CANfigurator User Guide 13 10 2014 CANGO YouKnowEverything TH 5 Successful installation of the CANfigurator application i Setup CANfigurator o E Completing the CANfigurator Setup Wizard Setup has finished installing CANfigurator on your computer The application may be launched by selecting the installed icons Click Finish to exit Setup Lila CANfigurator User Guide 13 10 2014 CANGO YouKnowEverything TTT 2 Using the CANfigurator Application CANfigurator application must be run with Administrator rights It will automatically ask for the permission of the administrator 2 1 Registration Request CANfigurator application needs a License KEY This key is obtained by sending CODE for register in an email addressed to support cango ro specifying the company information You will receive a License KEY which you will input and then press the Regi2. UPD upgrade file for FMS interface 2 Support FW_release GENERIC NEW VERSIONS w3 3 0 F0_J1939 v3 3 0 shass461la upd rd Load update file No response from CANGO FMS interface Please disconnect and reconnect the interface If the update process was completed the following window appears Information y OK 14 CANfigurator User Guide 13 10 2014 The update process is assisted by a progress bar Qy CANGO CANfigurator File Settings CANbus Update Setings CAN bus input A Output Undste UPD upgrade file for FMS interface 2 Support FW_release GENERIC NEW VERSIONS w3 3 0 F0_J1939 v3 3 0 shas3461la upd 13 10 2014 12 37 08 Open and reading the UPD file Me CONNECTED on COMA CANGO CANFigurator W118 NOTE Wr CANGO YouKnowEverything TTT ra Load update file m Check Online EXIT 13 10 2014 12 37 08 Entering in CFG made 13 10 2014 12 37 08 CANGO FMS ir 10 FO_J1939 v3 3 0 sha334811la noazo LEASE WAIT 13 10 2014 12 37 After the firmware update the device will return to the default settings and configuration This will reset the baud rate to 115200 b s if the UART baud rate was set different then the default settings you need to change the baud rate to be able to communicate again 15 Ur CANfigurator User Guide 13 10 2014 CANGO YouKnowEverything THT 2 5 1 Hard Reset Sometimes the FMS interface will need to have a Hard Reset of the syst
3. baudrate Readable table 0 Spreadsheet Start delay time T1 frame instants T2 frame totals E T5 frame tacho 100000 T6 frame mils 125000 Reserved Reserved Reserved i 0 30 30 0 0 0 0 0 0 Reserved 1000000 Handshake AutoBaud Get config from device Calibration coefficients Speed Field separator 1 000000 Set config to device Fuel consumptio Prefix 1 000000 NULL Load configuration file Save configuration file Suffix Default configuration CR LF CanGo FMS interface version ver HW 333 1211 SW 344 1211 CNG TACHO F7_MB_HEAVY_v3 3 0 sha334811 MS CONNECTED on COM4 CANGO CANfigurator W118 Frame mask Engine Speed Acc pedal Engine Load TCO CCVS Service Distance Vehicle Distance Engine Hours Fuel Consumption Vehicle Weight Engine temp Fuel Level Vehicle ID Ambient Ternp Driver ID Fuel Economy Fuel Rate PTO Engagement Total Fuel High Resolution reserved reserved reserved reserved reserved reserved reserved 13 10 2014 12 22 10 Wr CANGO YouKnowEverything Hd CANfigurator User Guide 13 10 2014 If the UART baud rate is changed when setting the device configuration the software will warn you with the message bellow Press Yes to change the serial port connection baud rate to the selected baud rate or press No to continue with the same baud rate Serial Port Baud change detected in the upload
4. interface The FMS interface will automatically check for the CAN bus network and will select the following options e Select between the CANgoclick or CAN wires e Select the CAN baud rate e Select if the FMS interface is in read only or read write mode e Selects if the Play feature is available or not After making the automatic selection the FMS interface will make a report to show the correct configuration to connect to this CAN network 250K CAN Network detected on CAN1 wires Connected on CAN1 wires in read only mode Play feature is not available OK If after pressing CONNECT to make the connection with the interface the following window appears please try to connect the CAN1 wires or the CANGOclick to other CAN network No CAN data detected Connected on CAN1 wires in read write mode with play feature available x If after pressing CONNECT to make the connection with the interface the following window appears please contact support cango ro to get the last update of the firmware Installed firmware does not support auto detect feature Please upgrade to the latest version 12 Wr CANfigurator User Guide 13 10 2014 CANGO YouKnowEverything TTT 2 4 Viewing the RS232 Output To view the RS232 output of the FMS interface press the START button This will show you how the data is being transmitted from the RS232 port To save the data in a file press the Save log button and i
5. the serial ports This operation will take longer so please be patient Qy CANGO CANfigurator File Settings CAN bus Update Settings CAN bus input Serial frames Repeat time Start delay time CAN baudrate UART baudrate Frame mask Readable table a 33300 2400 Engine Speed 0 Ba Z Acc pedal Engine Load D D 46 Ico 0 Cccvs a n 7 Service Distance Serial port settings en Vehicle Distance Engine Hours Fuel Consumption Vehicle Weight i Engine temp Fuel Level ee Vehicle ID P pandhak Ambient Temp Spreadsheet Tl frame instants T2 frame totals T5 frame tacho T6 frame mils Baud rate 2400 S 4800 Reserved 4 Reserved Reserved o 0 0 0 0 0 0 0 0 Reserved 2 N Get config from device TTS Speed 115200 AUTO detect Tan Set config to device Fuel Economy Fuel Rate PTO Engagement Loadiconfigurationfile US consumptic Total Fuel High Resolution 1 000000 NULL reserved Save configuration file eo Suffix reserved Default configuration CRI LF reserved reserved reserved wer HWW 333 1211 SW 544 1711 CNG TACHO FO_J1939 v3 3 0 sha3s4811la ENER reserved i OT CONNECTED CANGO CANfigurator V118 15 10 2014 12 16 Caution Please connect to the serial port connected to the FMS interface before performing any operation The default settings of the interface are 115200bps no Handshake CANfigurator User Guide 13 10 2014 CANGO YouKnowEveryth
6. Wr CANGO YouKnowEverything TTT Frame mask Engine Speed Acc pedal Engine Load TCO ccvs Service Distance Vehicle Distance Engine Hours Fuel Consumption Vehicle Weight Engine temp Fuel Level Vehicle ID Ambient Temp Driver ID Fuel Economy Fuel Rate PTO Engagement Total Fuel High Resolution reserved reserved reserved reserved reserved reserved reserved 13 10 2014 12 15 Menu Submenu Comments File EXIT Existing the application FMS interface Settings for the FMS interface Settings Serial port Settings of the serial port for the connection of the PC to the interface Always on top Makes the FMS interface stay on top of other applications Switch s to the CAN bus input tab for the capture and play function of the CAN bus FMS interface Update Switch s to the Update tab for updating of the FMS interface Ur CANfigurator User Guide 13 10 2014 CANGO YouKnowEverything TTT 2 2 2 Serial Port Settings 1 List of the COM ports of the computer Here you select the serial port used to make the connection to the FMS interface 2 Select the speed of the serial port 3 Refresh button refreshes the COM list 4 CONNECT button connect to disconnect the serial port 5 Close button closes the window 6 Handshake setting for the serial port 7 AUTO detect button automatic detection of the FMS interface connection to all available serial ports and to all the speeds of
7. YouKnowEverything CANfigurator User Guide V1 18 UWP CANfigurator User Guide 13 10 2014 CANGO YouKnowEverything MAAA Table of Contents CANN UO US LS acc cs rence ate sarctaedins e Eee E e EER d l AYVSCAN AG OW asessscacccecasetcaciaesvsasasteneweseascneennetaseinesvensedatvecnsseteseasenotanssausrsasssasmnersoaretesanctaosiaveysorngeteeeneoetaats 2 1 1 Installation of CANfigurator Application ccccccccccccccccecceseeeeeeseeeeecccceeceeeeeeeeeaaaaansesees 2 12Instalaton Sieps cide ccc tsce ccc set eas utes csi Ie cpa esc alec vc E EN R 3 2 Using the CANfigurator Application ccccccccccccccccceecccceasesssssseeeeeeecccceeeeessesaaaaaaaseseeeeeeeeeeees 6 2 1 Registration REQUESL gccsssdezissssesaseediandancevedessessieviassuosssendinndnedevedensaeeiesrtuaseuseeaelannitedtbedaniaerieatusteeses 6 2 2 Using the ZN Oy INCA Osos gcc shicasse decccnieus aca ceweudeceisn ghasasec ET 7 Die Mis Na NO eren a E A E A E 7 2 2 2 Serial Port SetinoS seeria rE E ATAT EA EER 8 2 2 3 Connecting to the FMS Interface 0 0 cceccssssssseeeececccceeeeeeeecaaaeaessseeeeeececeeeeeeeeeeaaaas 9 2 2 4 Serial Port Connection Error cccccccccessssnccececeeeeeeeeeeeesssenecesssnnneeeeeeeeeeeeeeeeeseeneeeeeas 9 2 2 5 FMS Interface Configuration 0 0 ccc cccccssssssssesssssesessssssssssssssssasssssaasaasaaaaaaaaaaaaaaaaas 10 2 3 Capturing Messages on the CAN BUS c
8. ab you can configure the FMS interface e The type of serial frames for the serial output e The repetition times and offset times of the serial frames e The CAN bus baud rate and select auto baud rate e The RS232 serial port baud rate and handshake e The type of information for Readable table and Spreadsheet e Calibration coefficients of speed and fuel consumption e The separation character between the frame values e The prefix and suffix of the serial frames Wr CANGO YouKnowEverything H d You can see the interface configuration by pressing the Get config from the device button Caution the previous values will be rewritten and the interface version will be updated To save the configuration to the interface press the Set config to device button Various configurations can be saved Save configuration file button and loaded Load configuration file button or you can go back to the initial values Default configuration button Please note when you save configuration file it will also save the CAN baud rate so do not have only one CANfiguration file for all the vehicles or select the AutoBaud option There are some firmware s F4 F8 TO CO that are read write firmware so do not select the AutoBaud option on this cases ly CANGO CANfiqurator File Settings CAN bus Update Settings CAN bus input R5232 Output Update Serial frames Repeat time CAN baudrate UART
9. ccccccccccccccceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeess 10 2 4 Viewing the RS232 Out ue snsistcccccveeechenetecivcetecckeectdeccdvctwecbenctdeddcuetwectceutvecddstdvecbenctsiecddesleectesedeeses 13 2 5 Update Interface Firmwate 00s ss sssssssccccsscssseccsssesssesesssssssecccccessseccccsssssesssssssscecccccsseees 14 Dis Mes RA ROS OU E ER T EE EA E E unease seedeb E E A E A 16 Lila CANfigurator User Guide 13 10 2014 CANGO YouKnowEverything TEL CANfigurator User Guide This guide will help you use the CANfigurator software It will show you how to install the application and how to use it to configure update the FMS interface capture messages on the CAN network as well as view the RS232 output of the FMS interface 1 Installation To install be CANfigurator application you need a computer with the following e Operative system Windows XP Windows 7 or Windows 8 e Minimum 1GHz processor e Minimum 5MB HDD space e Minimum 512MB RAM memory e Local serial port serial or USB RS232 adaptor e A serial cable 1 1 Installation of CANfigurator Application To install the CANfigurator application please ask for the latest version of the software from support cango ro or visit the website www cango ro files CANfigurator_setup_V1 18 exe You will receive an executable file Run the CANfigurator_setup_Vx y exe file and follow the installation instructions Caution If you already have ins
10. ed configuration Do you want to also change the Baud Rate setting to configured value Choose Yes if you want to communicate further with configured device Choose No if you want to configure another device 2 3 Capturing Messages on the CAN Bus The messages on the CAN bus are captured on CAN1 cables or on the CANGOclick of the FMS interface To start the capturing of CAN messages press the CONNECT button The data captured can be saved in a file if you select the capture in file option CANGO CANfigurator File Settings CAM bus Update Settings CAN bus input DD MM YYYY 13 10 2014 13 10 2014 13 10 2014 13 10 2014 13 10 2014 13 10 2014 13 10 2014 13 10 2014 13 10 2014 13 10 2014 13 10 2014 13 10 2014 13 10 2014 Time 12 25 10 404 12 25 10 404 12 25 10 416 12 25 10 416 12 25 10 417 12 25 10 033 12 25 10 041 12 25 10 041 12 25 10 041 12 25 10 042 12 25 10 042 12 25 10 042 12 25 10 042 JAA OR eim e e e A G G co co CO C oo co Co Oo Co O0 CO CO CO START PLAY Capture in file El play by file EE CONNECTED on COM4 Frames Count 13 10 2014 12 25 CANGO CANfigurater V118 11 Or CANfigurator User Guide 13 10 2014 CANGO YouKnowEverything H d If after pressing CONNECT to make the connection with the interface the following window appears please reset the interface and make the connection again Error entering in LOG mode Please check connections with FMS
11. em to be able to update a new firmware Instruction to make a Hard Reset 1 Go to the Update tab 2 Choose a firmware with Load update file and then press update button 3 It will appear the following Error window 4 Follow de instruction written Error window e Disconnect the interface from the power supply e Press the OK button e Connect the power supply to the FMS interface Qy CANGO CANfigurator File Settings CAN bus Update input R5232 Output Update UPD upgrade file for FMS interface Support FW_release GENERIC NEW VERSIONS w3 3 0 F0_J1939 w3 3 0 sha33461la upd dr 1 disconnect the power of FMS interface 13 10 2014 12 38 30 ERROR N 2 press OK 13 10 2014 12 38 30 Try to ent 3 connect the power of FMS interface The time out 20 sec Please wait Please check serial connection Me CONNECTED on COMA CANGO CANfigurator v1 18 13 10 2014 12 38 NOTE After the firmware update the device will return to the default settings and configuration This will reset the baud rate to 115200 b s if the UART baud rate was set different then the default settings you need to change the baud rate to be able to communicate again 16
12. ing TEL 2 2 3 Connecting to the FMS Interface To connect to the FMS interface you have to follow the steps below 1 Power the FMS interface by connecting power of the interface 2 Connect the interface to the RS232 port of the computer or to a USB RS232 converter 3 Start the CANfigurator application with administrator rights 4 Select the Settings menu and then the Serial port submenu 5 Select the serial port and the speed 6 Ifnecessary also check Handshake 7 Press the CONNECT button which will change to DISCONNECT 8 If all is ok then the status bar of the application will show a green indicator and the text CONNECTED on COMx Caution The AUTO detect button can be used to show the speed and the com port where the FMS interface is connected This process takes a little longer so please be patient 2 2 4 Serial Port Connection Error To read or configure the FMS interface it must be connected to the selected serial port through a regular serial cable In case of error the window below will appear of OK If the FMS interface does not answer to the commands the following window will appear Please reset the FMS interface select another serial port or try the AUTO detect button No response from CANGO FMS interface Please disconnect and reconnect the interface CANfigurator User Guide 13 10 2014 2 2 5 FMS Interface Configuration In this t
13. nsert the name of the file If you wish to delete the date press the CLEAR button The Clear stored data button resets all data stored on the FMS interface odometer operating hours By pressing the Request T2 frame you can see the T2 frame CANGO CANfigurator File Settings CAN bus Update CAN bus input 0 00 00 56 000 EngSpeed 0 000 rom Accel 0 0 Load 0 0 TCO 0 0 km h MD 0 050 DIO TP 0 HIO EV 0 D1 0 0 0 D2 0 0 0 Speed 0 00 km h CC 0 BR 0 CS 0 PTO 0 Service 0 km Distance 93802609 km EngHours 222 85 h Fuel 45027 53 L Weight 0 kg n 0 kg n 0 kg n EngTemp 0 degr FuelLew 0 0 VehID Ambient tempu n a degr Driver ID n a n a Fuel Economy Rate 0 00 L h Inst economy n a km L PTOEN 0 HRLFC 45027 535 L FMS 2 0 Diag Reqd Set odometer CONNECTED on COM4 fll 13 10 2014 12 33 When the odometer is not present on the CANbus network this parameter will be calculated by the FMS interface using speed You can set this parameter using the window bellow 13 CANfigurator User Guide 13 10 2014 CANGO YouKnowEverything TTT 2 5 Update Interface Firmware To update the FMS interface firmware 1 Go to Update tab 2 Press Load Update File Button to select the updating tab 3 Press the Update button and wait for the updating to be complete TU CANGO CANfiqurator Y g File Settings CAM bus Update CAN bus input R5232 Output U
14. ster button CODE for register License KEY Please send a email with the code If the next window appears then the code is not correct and you have to input it again or repeat the previous Step Licence KEY invalid CANfigurator User Guide 13 10 2014 2 2 Using the Application The home page includes the following components 1 Main menu functionalities and settings of the application 2 Tab set functionalities of the application 3 Status bar information on the functionalities of the application CANGO CANfigurator File Settings CANbus Update Settings CAN bus input Serial frames Repeat time Readable table 2 Spreadsheet T1 frame instants T2 frame totals T5 frame tacho E T6 frame mils Reserved Reserved Reserved 0 0 0 0 0 0 0 0 0 Reserved Start delay time 0 a jl aj a amp amp o amp Calibration coefficients Speed 1 000000 Set config to device Load configuration file 1 000000 Save configuration file Default configuration CanGo FMS interface version Fuel consumptia CAN baudrate UART baudrate E 33300 50000 E 100000 S 125000 250000 57600 500000 115200 1000000 C Handshake AutoBaud Field separator Prefix NULL Suffix CR LF ver HW 333 1211 SW 344 1211 CNG TACHO FO_1939_v3 3 0 sha334811a EE CONNECTED on Coma 2 2 1 Main Menu CANGO CANfiqurator V116
15. talled another version of the software it is preferable to first uninstall the old version the installation program will ask this automatically Please uninstall first the old wersion With the CANfigurator version V1 18 when the software will have a new update version the software will warn you that there is a new version available and this window will pop up when you will open the software Information am mm Mew version available V1 18 Do you want to download the latest version CANfigurator User Guide 13 10 2014 1 2 Installation Steps 1 Select the directory where you wish to install the application B Setup CANfigurator Where should CANfigurator be installed Setup will install CANfigurator into the following folder To continue cick Next If you would like to select a different folder click Browse C Program Files CANfigurator At least 2 6 MB of free disk space is required i5 Setup CANfigurator Select Additional Tasks Which additional tasks should be performed Select the additional tasks you would like Setup to perform while installing CANfigurator then click Next Additional icons V Create a desktop icon ete Genet Wr CANGO YouKnowEverything H Lila CANfigurator User Guide 13 10 2014 CANGO YouKnow Everything TTT 3 Display of the installation information Ready to Install Setup is now ready to begin installing CANfigurator on your computer
Download Pdf Manuals
Related Search