Bedienungsanleitung Operating Instructions Guide d
Contents
1. Only fill the bean container with coffee beans Never fill ground freeze dried or caramelised coffee beans into the bean container e Place the lid on the container 46 Filling the water reservoir e Flip up the lid of the water reservoir Fig A no 6 and pull the water reservoir up and out of the appliance e Fill the water reservoir with fresh water to the Max mark and reinsert it in the appliance Note If the water reservoir runs empty during an operating process e g during the coffee dispensing process the symbol for the water reservoir will be illuminated The current operating process will be concluded and the water reservoir must be filled before starting a new process Switching on 1 Caution Only switch on the appliance without the Claris water filter and when the water tank is full Only insert the Claris water filter into the water tank after switching on the appliance Fill the water tank to the max mark with fresh water before switching on the appliance e Place a bowl under the outlet e Press the on off button C1 to switch the appliance on The standby symbol is flashing The device heats up After heating up water will run out of the outlet and into the bowl Subse quently the standby symbol and the bean symbols are illuminated The device is ready for operation Note When starting up the appliance for the first time air and water f2. Cosy cjuub ele kelp a a cas ere mene ter E wore nt re ror E E reser rere 57 FG TS AN A i atte a rn EEE E E 58 Once holalg e 1860 i eEnen Tern rrr treater tee mnt Tenn tertey E ey Cererte eer 59 Ge aleve elle chal eee mere ane S oer ar ne creer eer eer ener 37 E D T a E A 60 lato coica Wee Cua oly prO CTAN n E E 61 J Palio gchncta decae iag POR a inaa A tree cree 64 THa A aA E EE ENA EE EE E 66 Preparation for transport protection against freezing and measures for longer eo E a E E E E E E E E 66 Founi o noo aa AE NEEE mere ners 68 39 For better orientation fold out the fold out pages on the front and back of these operating instructions Symbols in the text of these operating instructions The symbols in these operating instructions indicate specific hazards associated with handling your Melitta SOLO or provide useful tips Texts with this symbol contain information for your safety and indicate possible accident and injury hazards Texts with this symbol contain information about incorrect operation that should be avoided and indicate possible material damage hazards Texts with this symbol contain additional valuable information for hand ling your Melitta SOLO Intended use The Melitta SOLO is only designed for preparation of coffee and espresso Intended use includes a 2 3 Z ca e that you carefully read understand and comply with the operating instructions e that you part
3. The appliance is ready for operation 63 Integrated decalcifying program The integrated decalcifying program removes lime scale in the interior of the appli ance It takes a total of approximately 25 minutes The symbol for decalcifying flashes during the entire process Prerequisite The appliance is switched off Remove the Melitta Claris water filter if present from the water reservoir see page 49 1 Caution Execute the integrated decalcifying program every 3 months or when the symbol for decalcifying X 1s illuminated in the display Only use the decalcifying agent from Melitta for automatic coffee makers This decalcifying agent is precisely matched to the Melitta SOLO Never use vinegar or other decalcifying agents Execute the integrated decalcifying program as follows 1 64 Simultaneously press the button for two cup dispensing and the On Off button for more than 2 seconds The symbol for decalcifying H flashes and the symbol for the drip tray I amp R is illuminated Empty the drip tray and then reinsert it The symbol for the water reservoir is illuminated Flip up the lid of the water reservoir Fig A no 6 and pull the water reservoir up and out of the appliance Pour the descaler powder into a separate bowl filled with 0 5 1 of hot water Stir in the descaler powder e g with a long spoon As soon as the descaler powder is completely dissolved
4. Caution To avoid damage to the appliance surface do not use any micro fibre cloths scouring cloths sponges or cleaning agents Do not clean the drip tray and brewing unit in the dishwasher this could cause deformation Note The coffee grounds container Fig A no 1 is dishwasher safe and can be washed in the dishwasher Frequent washing in the dishwasher can cause slight discolouration on the collection container for coffee grounds 59 Cleaning the brewing unit Prerequisite The appliance is switched off 60 Note For optimal protection of your appliance we recommend that you clean the brewing unit once a week Reach into the recess on the right side of the appliance Fig A no 11 and pull off the cover to the right Activate the red button on the handle of the brewing unit Fig B no 1 and turn the handle in the direction of the arrow to the stop approxima tely 75 Use the handle to pull the brewing unit out of the appliance Leave the brewing unit as it is do not move or twist the components of the brewing unit Thoroughly rinse off the brewing unit as a whole from all sides under running water Particularly ensure that the surface shown in Fig D is free of coffee residue Do not put the brewing unit in the dishwasher Let the brewing unit drip dry If necessary remove coffee residues from the surfaces in the interior of the appliance where the brewing unit is inserted Put the brew
5. Symbols in the text of these operatno 11S CHONG ctor isioresrscasversnmieasnanaceedins 40 ea e E a A A E E 41 Nonini nd o T E aa a E E N 41 Gereral saron o EONS ee EO E EER E SE 42 E E 0 1610 A ENE E eer rae 43 EE aes E E A E E A E E O ty amr rrenr rt T 43 10 TI EE OANE A E E E A E A reer 44 E E E A E gael ENEE E A E A 45 S A e E R E E A 45 Do a E T E E A E E E 46 a E E A A A E rer arnt ver rrrer rere tyr ary ts 46 Fe AMUN 1S waer VOCE osrin E ntbag hota eniberaeelt 47 SASE a terse nce thee haces E A T A 47 Adj st ng the amount OF coftee that will D dispensed scsrsccaserserssernewsaiesrserecnriocee 48 PGs ne e IIS SEC ROT ara ve totcorecen sanctions eatuscorehereepeceuet 48 Inserino the Melitta Clits water TICEI csc sesceceatecatscprsataiassscparesagiaesieasernsesnsaneuetees 49 Pepaans coe Mo pIE S O emer rer tet tte een eee nen eee ene ee ee 50 Preparing acup ol CO Le fo rresia Ena Rian AE 50 Preparan two cups Ol coffee CSP CS 50 semini parion an ranan Tiesi 51 heaves DUO est Ose And operino MOJ PP RMT ere Rema tre nner ate aaia 52 a a a O ET E E E A rare tere 52 E a a E cme E Uren E E A E T 52 38 PO R ae elo renee em eee cer Ene err rT ete eee E 53 e CS ENC N OE E 53 am Setting the imer fof enetgy saving standby Mode ssrin sariini 54 DCH Ie the Cie Tor the AOC TCO sypsena eerk es eeamentepaasteracamrties 55 5 Aduse ihe brewing Pet A saat scan in atpeo iis setarsuneasmesiioasecieden anesasacarsaantseneneiene 56 A
6. pour the descaler solution into the water tank Re insert the water tank Warning The decalcifying agent can cause skin irritations Comply with the safety instructions and the quantity information specified an 2 3 Z ca on the decalcifying agent packaging 6 Press the button for brewing strength to start the integrated cleaning program The integrated decalcifying program will start Water flows inside the appli ance into the drip tray in multiple intervals This process lasts approximately 15 minutes Subsequently the symbol for the drip tray will be illuminated 7 Empty the drip tray and then reinsert it The symbol for the water reservoir 1s illuminated 8 Rinse out the water reservoir and fill it with tap water to the Max marking 9 Press the button for brewing strength 0 to continue with the integrated decalcifying program Water flows out of the outlet as well as in the interior of the appliance into the drip tray This process lasts approximately 5 minutes Subsequently the symbol for the drip tray will be illuminated 10 Empty the drip tray and then reinsert it The standby symbol 1 is illuminated after a brief heat up phase The appliance is ready for operation 11 Reinsert the Melitta Claris water filter into the appliance 65 10 Transport and disposal Preparation for transport protection against freezing and mea sures for longer periods of non u
7. saving stand Symbols in the display are Wake up by pressing the brew by mode dimmed ing strength button Display is not illuminated Switch on by pressing the device is de energised On Off button Auto off function Energy saving standby mode The appliance switches to energy saving standby mode automatically temperature of the heating element is lowered to save energy after the last action depending on the setting For this you can set the timer to different times or switch off the function completely See page 54 for more information in this regard Auto off function The device switches off automatically after the last action depending on the setting For this you can set the timer to different times See page 55 for more information in this regard 52 8 Function settings Adjusting the water hardness an 2 3 Z ca Use the included test strip to determine the water hardness in your area Comply with the instructions on the test strip package The appliance is factory adjusted to water hardness 4 If you have inserted the Melitta Claris water filter water hardness 1 is set automatically see p 49 Prerequisite The appliance is ready for operation the standby symbol is illuminated To maintain appliance quality adjust the water hardness as follows e Simultaneously press the button for single cup dispensing and the button for two cup dispensing for mote than 2 seconds The standby
8. this appliance if it is in faultless condition Never attempt to repair the appliance yourself If repairs are necessary contact the Melitta Service Hotline only Do not make any changes to the appliance its components or to the supplied accessories Never immerse the appliance in water Z Jever touch the appliance with wet hands or feet Z ever touch hot appliance surfaces Never reach into the interior of the appliance when it is in operation Z ever open the right cover during operation unless you are expressly requested to do so in these operating instructions Comply with the safety instructions in the other sections of these ope rating instructions 42 3 Appliance description Legend for Fig A 1 Drip tray with cup plate and collection container for coffee erounds internal as well as float display for full drip tray Height adjustable coffee outlet camila Button for single cup dispensing at 2 3 Z ca Button for two cup dispensing Water reservoir Bean container Display On Off button 1 Right cover removable covering the grinding fineness bl eo Button for brewing strength adjustment element brewing unit and type plate 43 Display Symbol Display Explanation prompt Appliance is heating up or coffee Standby dispensing e aie Iuminated Fill the water reservoir Water reservoir Flashing Insert the wate
9. unit back into the appliance and turn the handle of the brew unit anticlockwise to the stop to lock the brew unit Insert the four catches of the cover in the back of the appliance and swing the cover to the left until it engages Integrated cleaning program The integrated cleaning program removes residues including coffee oil residues that cannot be eliminated by hand It takes a total of approximately 15 minutes Prerequisite The appliance is switched off an 2 3 Z ca 1 Caution Run the integrated cleaning program every 2 months or after approxi mately 200 brewed cups of coffee at the latest however run the program when the symbol for cleaning is illuminated in the display Only use the cleaning tabs from Melitta for automatic coffeemakers These tabs ate precisely matched to the Melitta SOLO Use of other cleaning agents can damage the appliance Run the integrated cleaning program as follows 1 Flip up the lid of the water reservoir Fig A no 6 and pull the water reservoir up and out of the appliance Fill the water reservoir to the Max mark and re insett it Simultaneously press the button for single cup dispensing and the On Off button O for more than 2 seconds The symbol for cleaning flashes during the entire process The symbol for the drip tray flashes Empty the drip tray and the coffee grounds container Re insert the drip tray without the coffee grounds container an
10. DEUTSCH Mol bee ENGLISH CAFFEO SOLO 2 a o 4 aa NEDERLANDS ESPANOL Version 1 0 07 2009 Bedienungsanleitun Manual de Instrucciones Melitta Haushaltsprodukte S i S f i E Gabi Ca ce Operating Instructions N vod k obsluze Guide utilisation N vod na pou itie D 32372 Minden Gebruiksaanwijzing Nn VA D a 7 Dear customer Congratulations on buying a Melitta SOLO fully automatic coffeemaker an 2 3 Z ca We would like to welcome you as a coffee lover and Melitta SOLO gourmet With this Melitta SOLO quality product you will experience many special cof fee moments Enjoy your favourite coffee or espresso specialities and indulge yourself with all your senses Please read these operating instructions carefully all the way through so that you and your guests enjoy the longest possible satisfaction with the Melitta SOLO Keep these operating instructions in a safe place Should you require more information or if you have any questions on the cof feemaker please contact us directly consult with your local stockist or visit us on the Internet at www meltta de ot www melitta eu We extend our best wishes for your satisfaction with the Melitta SOLO Your Melitta SOLO team Registered trademark of a company of the Melitta Group 37 Table of contents Information about these operating INSU CT OUS eci sesensassunnroasoncetansstnassseaniasusaassane 40
11. andby symbol 1 is illuminated Adjusting the brewing temperature The brewing temperature is factory set to level 2 medium Prerequisite The appliance is ready for operation the standby symbol is illuminated Adjust the brewing temperature as follows to meet your requirements e Simultaneously press the button for single cup dispensing and the button for two cup dispensing for mote than 2 seconds The standby symbol 1 is flashing e Press the button for single cup dispensing four times to call the menu for brewing temperature The symbol for cleaning 1s flashing e Press the button for brewing strength W to select between the three pos sible brewing temperatures 56 Display Brewing tempera S an 2 3 Z ca a factory setting e Press the On EOR Off button nr to confirm the selected brewing tempera ture All symbols in the display flash briefly for confirmation The appliance is ready for operation the standby symbol is illuminated Resetting to factory settings To reset the device to the factory settings execute the following points Prerequisite The appliance is ready for operation the standby symbol is illuminated e Simultaneously press the button for brewing strength and the On Off button D for more than two seconds All settings will be reset to the factory settings The standby symbol will flash briefly for confirmation Ove
12. d for a longer period of time After inserting the Melitta Claris water filter excess active charcoal will be washed out of the filter the first time the appliance is rinsed out This can cause a slight grey colour of the rinse water Subsequently the water will again be cleat 6 Preparing coffee espresso Preparing a cup of coffee espresso Prerequisite The appliance is ready for operation e Place a cup under the outlet e Press the button for brewing strength to adjust the brewing strength e Turn the coffee quantity regulator Fig A no 3 to adjust the cup fill quantity e Press the button for single cup dispensing The grinding process and coffee dispensing start The standby symbol is flashing Dispensing ends automatically when the set coffee fill level is reached e To break off the dispensing of coffee prematurely press the button for single cup dispensing 0 50 Notes When the appliance is started up for the first time the grinder will grind longer than usual an 2 3 Z ca You can also adjust the cup fill quantity during the dispensing process To dispense less coffee turn the coffee quantity regulator to the left to the desired quantity or turn it until the appliance stops dispensing To dispense more coffee turn the regulator to the right Preparing two cups of coffee espresso Prerequisite The appliance is ready for operation e Place two cups under t
13. d place the coffee grounds container under the outlet First two automatic rinsing cycles are executed Then the standby symbol is illuminated ol Reach into the recess on the right side of the appliance Fig A no 11 and pull off the cover to the right Press and hold the red button on the handle of the brewing unit Fig B no 1 and turn the handle clockwise to the stop approximately a 61 8 Use the handle to pull the brewing unit out of the appliance The standby symbol 1 and the symbol for cleaning will flash alternately as long as the brewing unit is out of the machine 1 Caution Danger of damaging the brewing unit During the cleaning program only remove the brewing unit at the time specified here 9 Leave the brewing unit as it is do not move or twist the components of the brewing unit 10 Thoroughly rinse off the brewing unit as a whole from all sides under running water 11 Let the brewing unit drip dry 12 Place a cleaning tab in the brewing unit Fig C 13 Put the brew unit back into the appliance and turn the handle of the brew unit anticlockwise to the stop to lock the brew unit The symbol for cleaning will continue to flash the standby symbol is not illuminated The symbol for the water reservoir is illuminated 14 Insert the four catches of the cover in the back of the appliance and swing the cover to the left until it engages 15 Flip up the l
14. grounds container is located in the drip tray Please ensure that the drip tray is pushed into the appliance all the way to the stop Notes Keep the packaging material including the hard foam material on hand for transport and possible return shipments to avoid transport dama ge Itis normal to find traces of coffee and water in the machine before it is started up for the first time This is because the appliance was tested for faultless function in the factory 45 Connecting e Plug the power supply cord into an earthing contact socket outlet with at least 10 A fuse protection N Warning Danger of fire and danger of electric shock due to incorrect supply voltage incorrect or damaged connections and power cord Ensure that the supply voltage agrees with the supply voltage specified on the type plate of the appliance The type plate is on the right side of the appliance behind the cover Fig A no 11 Ensure that the power outlet satisfies the applicable standards for elec trical safety If in doubt contact a qualified electrician Never use damaged power cords damaged insulation bare wires During the guarantee period only have the damaged power supply cord replaced by the manufacturer after the guarantee period only have it replaced by qualified specialists Filling the bean container e Remove the lid of the bean container and fill the container with fresh coffee beans 1 Caution
15. he brewing unit see p 60 e Transport the appliance in the original packaging if possible including hard foam elements to prevent transport damage C Caution Do not transport or store the appliance in low temperature vehicles or rooms as the residual moisture could freeze or condense and cause dama ge to the appliance Disposal e Please dispose of the appliance in an environmentally responsible manner via suitable collection systems 67 11 Troubleshooting Coffee only runs Grinding level too fine drop by drop Coffee does not flow Water reservoir not filled or it is not inserted correctly Set the grinding level to a coat ser level Clean brewing unit Decalcify if necessary If necessary execute a cleaning program Fill water reservoir and ensure that it is seated properly Brew unit obstructed Clean the brewing unit Grinder does not Beans do not drop into grind coffee beans oily Foreign objects in the grinder Loud grinder noise Foreign objects in the grinder Insufficient quantity of Bean symbols are flashing although l the bean container is ing chamber filled The brew unit The brew unit is not cot cannot be re inserted rectly sealed after it has been removed The drive is not in the correct position 68 the grinder beans are too eround beans in the brew Tap lightly on the bean contai ner Contact the hotline Contact the hotline Press
16. he outlet one after the other e Press the button for brewing strength to adjust the brewing strength e Turn the coffee quantity regulator Fig A no 3 to adjust the cup fill quantity e Press the button for two cup dispensing The double grinding process and the dispensing of coffee start The standby symbol is flashing Dispensing ends automatically when the set coffee fill level is reached e To break off the dispensing of coffee prematurely press the button for two cup dispensing Notes When the appliance is started up for the first time the grinder will grind longer than usual You can also adjust the cup fill quantity during the dispensing process To dispense less coffee turn the coffee quantity regulator to the left to the desired quantity or turn it until the appliance stops dispensing To dispense more coffee turn the regulator to the right 51 7 Switching off and operating modes Switching off e If possible place a bowl under the outlet e Press the On Off button D to switch off the appliance The appliance automatically rinses out the coffee channel if coffee has been dispensed beforehand The brewing chamber moves into idle position The standby symbol 1 is not illuminated Operating modes Indicated by What is possible TE AD Eba Operating functions for bever Ready for operation and the bean symbols O age preparation are illuminated Energy
17. icularly comply with the safety instructions e that you use the Melitta SOLO within the operating conditions specified in these instructions Non intended use Non intended use applies when you use the Melitta SOLO in a manner that differs from the use described in these operating instructions N Warning Through non intended use you can injure yourself or scald yourself with the hot water or steam Note The manufacturer bears no liability for damage that is attributed to non intended use 41 2 General safety instructions Please read the following instructions all the way through Failure to comply with the instructions can affect your own safety and the safety of the appli ance Warning Keep the following objects out of the reach of children Packaging ma terial small parts All persons who use the appliance must be familiar with the operation of the appliance beforehand and they must be instructed in the possible hazards associated with the appliance Never allow children to use the appliance or play near the appliance unattended The appliance is not designed to be used by persons including children with restricted physical sensory or mental capabilities or with lack of experience and or knowledge unless they are supervised by a person who is responsible for their safety and have received instructions from this supervising person in how the appliance should be used Only use
18. id of the water reservoir Fig A no 6 and pull the water reservoir up and out of the appliance Fill the water reservoir to the Max mark with fresh tap water and reinsert it 16 Slide the coffee outlet Fig A no 2 all the way down 17 Press the button for brewing strength 0 to continue with the integrated cleaning program The integrated cleaning program will continue This process lasts approxima tely 5 minutes Water flows out of the outlet as well as in the interior of the appliance into the drip tray Subsequently the symbol for the drip tray g will be illuminated 62 18 19 20 2l 22 Flip up the lid of the water reservoir Fig A no 6 and pull the water reservoir up and out of the appliance Fill the water reservoir to the Max mark with fresh tap water and reinsert it Empty the drip tray and the coffee grounds container at 2 3 Z ca Re insert the drip tray without the coffee grounds container and place the coffee grounds container under the outlet The integrated cleaning program will continue This process lasts approxima tely 5 minutes Water flows out of the outlet as well as in the interior of the appliance into the drip tray Subsequently the symbol for the drip tray will be illuminated Empty the drip tray and the coffee grounds container Reinsert the drip tray with the coffee grounds container The standby symbol 1 is illuminated after a brief heat up phase
19. r reservoir Empty drip tray and coffee grounds container coffee grounds Pe 1 cof J E rashin Insert rip tray and coffee grounds container 1 bean mild l Illuminated 2 beans normal PER 3 beans strong strength i i l Fill bean container flashing ends after Flashing the next coffee dispensing process T b Clean appliance Clean a an a cleaning program is run Decalcify appliance Decalcify I l Flashing a decalcifying program is Note If all symbols in the display are dimmed the device is in energy saving standby mode 44 4 Starting up When starting the appliance for the first time please execute the following tasks When you have executed these tasks the appliance is ready for operation Thereafter an 2 3 Z ca you can prepare coffee We recommend pouring the first two cups of coffee after first start up down the drain Setting up e Place the appliance on a stable level and dry surface Ensure that there is a distance of 10cm to the wall and to other objects e The LATTEA has two rollers on the rear edge of the appliance Lift the appliance slightly from the front the rollers allow easy movement 1 Caution Never place the appliance on hot surfaces or in wet areas Do not transport or store the appliance in cold vehicles or rooms with low temperature because the residual moisture could freeze and damage the appliance Follow the instructions on page 66 e The coffee
20. rom the interior of the appliance escape into the drip tray 47 an 2 3 Z ca Adjusting the amount of coffee that will be dispensed Turn the coffee quantity regulator Fig A no 3 to variably adjust the dispensing quantity regulator to the left less coffee regulator to the right more coffee Coffee dispensing Regulator far Regulatorin Regulator far quantity left the middle right dispensing dispensing Adjusting the brewing strength 48 Press the button for brewing strength w several times to select from among three possible degrees of brewing strength Your selection is indicated by the bean symbols g in the display Display Brewing strength normal factory setting You can also change the coffee flavour via the fineness level of the grin der See page 58 for more information in this regard 5 Inserting the Melitta Claris water filter A Melitta Claris water filter for filtering out lime scale is included with the appliance After starting up the appliance for the first time please insert the water filter into an 2 3 Z ca the appliance If you use the filter you will decalcify the appliance less frequently and the water hardness will be set on hardness level 1 automatically See page 53 in this regard The service life of your machine will be extended thanks to the reliable protection against lime scale The water filter should be changed regularly every 2 months a
21. rview of factory settings Function settings Factory setting Water hardness Water hardness 4 eke alas Level 1 15 minutes standby mode Auto off function Level 1 1 hour evel 2 medi 57 Adjusting grinding fineness The grinding fineness level was optimally adjusted prior to delivery Consequently we recommend that you only readjust grinding fineness after approximately 1 000 coffee preparation processes approximately 1 year You can only set the grinding fineness while the grinder is running Thus adjust grin ding fineness directly after coffee dispensing starts If the coffee flavour is not sufficiently intense then we recommend that you set a finer grinding level e Reach into the recess on the right side of the appliance Fig A no 11 and pull off the cover to the right e Start a normal coffee dispensing process e While the grinder is running Place the lever in one of the three posi tions Fig E e Insert the four catches of the cover in the back of the appliance and swing the cover to the left until it engages centre medium right coarser 58 General cleaning 9 Care and maintenance an 2 3 Z ca Wipe off the outside of the appliance with a soft damp cloth and an off the shelf dishwashing detergent Empty and clean the drip tray Fig A no 1 regularly at the latest however when the float projects out of the drip grate Clean the coffee grounds container regularly 1
22. s illuminated Press the brewing strength button several times to select from four possible times for the timer o 15 minutes factory setting 30 minutes an 2 3 Z ca e Press the On Off button to confirm the selected time All symbols in the display flash briefly for confirmation The appliance is ready for operation the standby symbol is illuminated Note Press the brewing strength button W to wake the machine out of energy saving standby mode You can then directly dispense coffee Setting the timer for the auto off function Additional information on auto off function is provided on page 52 The timer is factory set to level 1 1 hour Prerequisite The appliance is ready for operation the standby symbol is illuminated Adjust the timer as follows e Simultaneously press the button for single cup dispensing and the button for two cup dispensing for mote than 2 seconds The standby symbol 1 is flashing e Press the button for single cup dispensing three times to call the menu for the Auto Off function The symbol for the drip tray g is illuminated 55 e Press the brewing strength button several times to select from four possible times for the timer Display 1 hour factory setting e Press the On Off button D to confirm the selected time All symbols in the display flash briefly for confirmation The appliance is ready for operation the st
23. se Allowing liquids in the appliance to evaporate We recommend that you dry out the appliance if it will not be used for an extended period of time This protects the appliance from damage due to freezing Prerequisite The appliance is ready for operation 66 Take the Melitta Claris water filter out of the water reservoir Simultaneously press the button for single cup dispensing 0 and the On Off button O for more than 2 seconds The standby symbol is illuminated after a brief heat up phase Subse quently the symbol for the water reservoir will be illuminated Flip up the lid of the water reservoir Fig A no 6 and pull the water reservoir up and out of the appliance Press the button for brewing strength 0 The device will be dried out automatically in the interior Subsequently the device switches off automatically Reinsert the empty water reservoir Note The Melitta Claris water filter should not remain dry over a longer period of time Consequently we recommend storing the Melitta Claris water filter in a glass of water in the refrigerator if the device will not be used for a longer period of time Transport e Dry out the appliance see p 66 e Empty and clean the drip tray and the coffee grounds container a 2 3 Z ca e Empty the water reservoir and the bean container If necessary use a vacu um cleaner to vacuum out any beans that are hard to reach e Clean t
24. symbol 1 is flashing rapidly e Press the button for single cup dispensing to call the menu for adju sting the water hardness The symbol for the water filter is illuminated e Press the button for brewing strength to select between the four pos sible degrees of water hardness Your selection of water hardness in accordance with the table is indicated via the bean symbols in the display very hard P l Pal E 53 Press the On Off button D to confirm the selected degree of water hardness All symbols in the display flash briefly for confirmation The appliance is ready for operation the standby symbol 1 is illuminated Note During the adjusting process if you do not press a button within 60 se conds the appliance automatically reverts to standby mode Setting the timer for energy saving standby mode Additional information on energy saving standby mode is provided on page 52 The timer is factory set to level 1 15 minutes Prerequisite The appliance is ready for operation the standby symbol is illuminated Adjust the timer as follows 54 Simultaneously press the button for single cup dispensing 0 and the button for two cup dispensing for more than 2 seconds The standby symbol 1 is flashing rapidly Press the button for single cup dispensing 0 twice to call the menu for adjusting water hardness The symbol for the water reservoir 1
25. t the latest however it must be changed when the symbol for the water filter is shown in the display Prerequisite The appliance is switched off e Simultaneously press the button for brewing strength and the on off button D for more than 2 seconds The symbol for the water filter flashes during the entire change procedure The symbol for the drip tray is illuminated e Empty the drip tray and then reinsert it The symbol for the water reservoir is illuminated e Flip up the cover of the water reservoir and pull the water reservoir up and out of the device e Empty the water reservoir e Screw the Melitta Claris water filter into the thread on the floor of the water reservoir e Fill the water reservoir with fresh water to the Max mark and reinsert it in the appliance e Press the button for brewing strength The device will execute an automatic filter rinsing process hot water in the interior of the appliance flows into the drip tray Subsequently the standby symbol and the bean symbols are illuminated The device is ready for operation and water hardness is automatically set to hardness level 1 e Empty the drip tray and then reinsert it 49 Notes The Melitta Claris water filter should not remain dry over a longer pe riod of time Consequently we recommend storing the Melitta Claris water filter in a glass of water in the refrigerator if the device will not be use
26. the control button for single cup dispensing ot two cup dispensing Check whether the handle for the locking mechanism is cor rectly locked in place Switch the appliance OFF and then ON again then press the operating buttons for single cup dispensing and two cup dispensing simultaneously for more than 2 seconds The drive will move into position Replace the brew unit and check that it is correctly locked in place Buttons for single Brewing unit is missing or Insert the brewing unit properly cup and two cup is not inserted correctly operation flash Brewing chamber is Switch off the appliance and alternately with the overfilled ENGLISH switch it on again via the On Off button On Off button repeat if necessary until standby mode is displayed Continuous flashing System error Switch off the appliance and of all buttons switch it on again via the On Off button if this does not solve the problem send the appliance to the service organi zation If you have additional questions please contact our service hotline at 49 0 571 86 1900 69
Download Pdf Manuals
Related Search