User Manual - Kodak PixPro
Contents
1. Time Lapse Loop recording Field of View Motion detection Wind Cut White Balance Exit Movie Size Movie Size refers to the image resolution during recording There are 7 options in Movie Size e 1080p30 1920x1080 30fps 960p50 1280x960 50fps 960p30 1280x960 30fps e 720p60 1280x720 60fps 720p30 1280x720 30fps e WVGA60 848x480 60fps e WVGA120 848x480 120fps When selecting WVGA120 the product shoots ultra high speed movies and plays back with normal 30 fps speed in order to capture visually indistinguishable moments easily When selecting WVGA120 the maximum recordable time is 60 seconds when the time reaches 60 seconds the product will automatically stop recording and return to the viewfinder state When selecting WVGA120 the sound cannot be recorded When selecting WVGA120 Time Lapse Loop recording or Motion detection cannot be enabled When selecting WVGA60 Time Lapse or Loop recording cannot be enabled The maximum recording time of a 4GB memory card GB Time Lapse Time Lapse enables the recording of an interval of time and splices the frames together to present a condensed video which usually requires a long period of time to complete There are 7 options in Time Lapse ES Off EI 1 second e J 2 seconds d i 5 seconds Bei seconds ofS 30 seconds gf 60 seconds Time2. automatically sense the product 3 Open the folder of the product on the computer and copy the data you need to the computer 4 After transmission is completed please cancel the USB connection by safely pulling out the USB device from the computer system 5 Pull out the USB cable The product will automatically shut down If connected to the computer USB port of 100mA the product will have no response due to insufficient power supply Pressing for more than 2 seconds will cause shut down and stop of communication between the computer and the product If a memory card is inserted in the product only files in the memory card will be read If needing to read the files in the internal memory please pull out the memory card before connecting to the computer HDMI Connected TV Output The product is capable of realizing movie and photo playback on a TV through HDMI The HDMI connection defaults to automatic connection mode Steps 1 Open the rear cover of the product connect one end of the HDMI cable not included to a TV which is up to the HDMI standard the TV and the product both need to be turned on and the other end to the cable to the HDMI port of the product The product will automatically enter the playback state after the connection is complete The operating method is the same as the Introduction to Basic Operation of Playback on page 31 If the product is connected to th
3. Align the location pole of the base to the location hole of the action cam and align the screw on the base to the tripod socket of the action cam Rotate the screw for fixing 4 Assemble the base pre tightening handle and vented helmet strap mount according to the direction illustrated in the picture First press the base into the vented helmet strap mount and then rotate and tighten the pre tightening handle Base gn tightening Handle Buckle Adhesive Mount Vented helmet strap mount B accessory applicable to bicycle helmet Installation Method 1 Align the location pole of the mount to the location hole of the action cam and align the screw on the holder to the tripod socket of the action cam and then rotate the screw with a tool like a coin to fasten a Y A VW CA vil 2 Expand the band first and then thread both ends of the band into the buckle Thread both ends of the band into the buckle and then press the buckle clamp Buckle Clamp Handheld mount accessory applicable to be handheld Installation Method 1 Align the location pole of the mount to the location hole of the action cam and align the screw on the holder to the tripod socket of the action cam rotate the screw for fixing Location Pole Surfboard adhesive mount accessory applicable to surfboard Installation Method 1 Align the location pole of the base to the location hole of the action c
4. Lapse method of operation 1 After selecting Time Lapse time press to back to the viewfinder status LCD will display corresponding icons 2 Press the LCD will display red font time countdown 3 Press again to finish recording Movie Size cannot be selected as WVGA120 or WVGA60 The sound cannot be recorded IS When Loop recording or Motion detection is enabled the Time Lapse feature cannot be used Loop recording Loop recording allows for the recording of independent segments of movies according to selected time length from the beginning of recording The product will continually record movies of the length selected until the record button is pressed to end recording When the memory card is full the product will overwrite the recorded files starting from the first movie circularly There are 3 options in Loop recording G Off e GA 5 minutes e Fy 10 minutes Loop recording method of operation 1 After selecting Loop recording time press to return to the viewfinder status LCD will display corresponding icons 2 Press to start recording 3 Press again to finish recording Movie Size cannot be selected as WVGA120 or WVGA6O When Time Lapse or Motion detection is enabled the Loop recording feature cannot be used Loop recording feature can only be used when there is a memory card in the product Turn off the product when the Loop recording function is enabl
5. Mire SZ 4 arth 20 BS Mode Display Time Lapse Display Burst Shot Display Loop recording Display Wind Cut Display Motion detection A 8 9 10 White Balance Display 11 12 13 Display Memory Card Display VEH ED 960 720 7A VON Ver 8 soe See SE Wide f Medium Narrow Water We 11 00 0123 e est 13 kr NZ INS Le Got d 7 TAN mee EES Some icons will automatically hide Still Size Display after a 2 second display Press Field of View Display to display all current setting Remaining Recording Message Time Display Number of remaining shots Display _ Indicates 16 9 display range Battery Status Display Internal Memory IN Indicates 4 3 display range Introduction to Basic Operation of Recording and Shooting 1 Enter the viewfinder status mode and press ol to switch between recording mode and shooting mode 2 Align the lens to the object to be recorded and press for recording or shooting 3 Under the recording mode repress the to stop recording Under shooting mode status when the product detects a human face a green focus frame will appear When two or more human faces are detected a green main focus frame and a white secondary focus frame will appear When the product rotates around the lens axis for 180 the display screen on the LCD is positive display When in still and video record mode the LCD may turn off t
6. lens clean Do not use corrosive alcoholic or organic solvent containing cleaners to wipe this product Do not use or store this product in high temperature environment Do not expose the lens to strong light sources e g Daylight etc for extended periods of time Do not use or store the product in strong magnetic field environment If the product is quickly transferred from a low temperature environment to a high temperature environment water condensation may occur in the product due to physical changes In this case it is recommended to wait until the product returns to room temperature before you turn it on If a photo or video cannot be played back due to human caused improper operation the Company shall assume no liability or responsibility for compensation Store the product in a dry and clean environment when you are going to store the product for a long period of time Waterproofing Notes Do not use the product below 10 meters 32 8 feet underwater The product will remain waterproof for one hour at the depth of 10m 32 8 feet Do not use this product in a geothermal spring or in water at a temperature greater than 40 C Please do not open the rear cover underwater If water accidentally comes in contact with the product please do not open the rear cover immediately Turn the product off and dry it with a clean dry and lint free cloth Then open the rear cover and remove the battery an
7. lt to return to the APP home directly Click playback in the APP Home to enter the playback state There are two playback options in the playback state e Index playback action cam smart device e Single photo movie photo Index playback action cam smart 2 The index playback interfaces of the device smart device and the action cam can be switched by shifting a red dot on the 1 Inthe APP Home click playback to tee eae the smart device cae enter the index playback state and enter the photo album of the action cam in default enter the viewfinder status download files in the action cam 3 The index playback interface of the smart device displays files downloaded from the action cam to the smart device into the smart device delete files e 0 enter the viewfinder status K selection of multiple photos Enter the selection interface after selecting A and click thumbnails so that files can be selected Clicking the same thumbnail for the second time will cancel selection F al GH 23 30 2 Items selected RA share Jl Slide play FD delete Setting function Click amp at the right upper corner of the interface so that the setting interface can appear Cache can be wiped in the Android system Cache can be wiped in the iOS where login and logout accounts also can be set Download function Downloading will be continue
8. please format the memory card first A photo or video taken with the product will be stored in the folder that is automatically generated on the memory card Do not store photos or videos that are not taken using the product in these folders in case that the files cannot be normally recognized in playback Do not directly edit the data on the memory card Copy the data to your computer disk before editing Do not modify the names of the files or folders on the memory card using your PC Modifying the name of the files or folders may cause the files to not be recognized by the product or possibly an error may occur Please turn the product off before removing the memory card Otherwise the memory card could be damaged When the product is stored for a long period of time please backup the data on the memory card and remove the memory card for storage Other Notes Do not disconnect the power or turn the product off during the update process Doing so may cause incorrect data to be written and the product may not power on later When using your product on an airplane observe the relevant rules specified by the airline Due to the limitations of manufacturing technology the LCD screen may have a few dead or bright pixels These pixels do no effect the quality of the photos or video If the LCD screen is damaged pay particular attention to the liquid crystal in the screen If any of the following situations arise
9. recording 3 Press again to finish recording Still Settings Introduction There are 5 options in First Level menu Still Settings e Still Size e Burst Shot e Field of View e White Balance e Exit Still Size The Still Size indicates the number of pixels used to capture the images A photo having higher image resolution contains more details and is capable of better meeting big screen fine photo printing requirements There are 3 options in Still Size 14MP 4320x3240 4 3 e 10MP 4320x2432 16 9 5MP 2592x1944 4 3 Number of photos that can be stored ona 4GB memory card amom MISE ECH Approximate maximum number of images 913 shots 4GB 1211 shots 4GB 2398 shots Burst Shot Burst Shot allows ten photos to be captured continuously one single time before auto pause There are 2 options in Burst Shot ITS Off Enable Burst Shot method of operation 1 After Enable in Burst Shot is selected press to return to the viewfinder status LCD will display corresponding icons 2 Press to enable Burst Shot shooting It will stop after 10 photos are taken Field of View Field of View means the image receiving angle range of the product There are 4 options in Field of View meng Ultra Wide EET Medium Deg Narrow e Water Ring Field of View method of operation 1 After selecting the Field of View angle press to return to the view
10. take the recommended immediate action indicated below 1 If liquid crystal comes in contact with your skin please wipe with a dry cloth wash thoroughly with soap and rinse with plenty of clean water If liquid crystal gets into your eye flush the eye immediately with plenty of clean water for at least 15 minutes and then seek for medical assistance If liquid crystal is swallowed immediately flush your mouth thoroughly with clean water and induce vomiting Seek for medical assistance GIONS YOU E 1 eege 4 OTE E 9 STIG Ready EE 13 Accessories Included cccscseccccsessereccssserenscsseccssesensascauersescasserensassessnsanereaes 13 e SE ea A a E E ee conaetaesia 15 Installing and Dismantling the Lens Cover 18 Installing Battery and Memory Card 20 GING E 22 Introduction to Various Button Functions 0 cccccccceccecceeeecececececececeaeaeaearers 23 Operation Method 25 MORON EE 25 Set your Language Date and Time after the first Dower op 26 LCD Screen DISplay scciecien asics scavenscaesearecceescascteesendedensldecsusatencedeviaedeeveeecendsonrstess 27 Introduction to Basic Operation of Recording and Shooting 28 LCD Screen Display under Playback Status cccccecceeeeseeeeeeeeeeeeeeseeeeeeaes 30 Introduction to Basic Operation of Playback 31 Introduction to the Setting Mode of Menu Options eens 36 Menti TRO GU CUO N E 37 Introduction to General Settings cceccccecs
11. tightening handle Mark Adhesive mount flat accessory applicable to skateboard Adhesive mount curved accessory applicable to helmet Installation Method There are two types of adhesive mounts flat and curved You may select based on the shape of the object to be used Both types can be assembled in the same way taking the adhesive mount flat as an example 1 Align the location pole of the base to the location hole of the action cam and align the screw on the base to the tripod socket of the action cam Rotate the screw for fixing es Location Pole Screw 2 Tie one end of the tether to the adhesive mount and the other end to the rear cover shaft 3 Assemble the base pre tightening handle and adhesive mount according to the direction illustrated in the picture First press the base into the adhesive mount and then rotate and tighten the pre tightening handle QI Pre tigntening Handle eg 1051 Mount 4 Tack the double sided adhesive at the bottom of the adhesive mount to the object to be used Double sided adhesive is disposable It can be purchased separately and replaced if needed Double sided adhesive Bar mount accessory applicable to bicycle Installation Method 1 Set the bar clamp to the handlebar and rotate the screw for fixing Bar Clamp 2 Open the bottom part of the fixing sleeve and set it in the Action Cam Insert the conn
12. AC adapter to Please enarge the Geier indoors charge the battery prior to use between 0 C and 40 C You may use external power supplies If connected to the computer USB port output voltage of 5V output current of 100mA the product will have no of 1A namely vehicle power supply response due to insufficient power or mobile power pack to charge the product Introduction to Various Button Functions Viewfinder status refers to viewfinder of recording and shooting To save power if the product is not operated for a period it will automatically enter the LCD off status Press any button can wake LCD F Display all information when the No action itis hidd Power Button It is hidgen Delete Button Press and hold turn off the product Recording mode Shooting mode switch Menu Button Playback Button Direction Button Lower No action OK Button Confirm selection No action Switch downward Enter single photo status No action Video Recording Button Enter viewfinder status Start recording Shooting Button except Wireless feature Shooting a photo Stop recording In the viewfinder status when the Motion detection or Time Lapse function is set to be enabled press to enter the state of preparing for video recording Movie Playback Single Photo e Plavina Back Fast Forwarding ying Rewinding Delete Back to the initial state of the movie Power Button Delete Button Press and hold turn o
13. Gef aubh Boe play soa kiami an ochi a Lite iia Getizv er f Py EA Audit H decoder network r i dalai Ben ee eee Subtitle san decodes E General He decoder 10 bit Like liters Qeesecer L e Hi ID eiar Pormal Correct aspect ratio rurari F deonder genect rabo i Ww decoder bere Color format DOFTWARE DECODER GENERAL SAN decoder local enge ee te Deinterlace Si Dentetooce by deim i SW decoder network Lise aw decoder Tying Fe Custom codec Special Accessories Let the action cam accommodate to your activity there are different options of accessories available Accessories bundle vary per distribution retailer To purchase additional accessories separately please contact your local retailer customer service support or visit www kodakpixpro com for more customer service details Before using especially in water or strenuous activity please pay attention to make sure the product is tightly secured to prevent damage or loss to the product Please ensure that the adhesive surface is clean before using double sided adhesive accessories Dirt grease or other foreign matter will reduce the effectiveness of the double sided adhesive After fully assembling the accessories please check to make sure that the screw and pre tightening handle are in the proper position and fully secure For ease of assembly please line up the marks on the base and pre tightening handle per the diagrams below Pre
14. Kodak PDPO SP Digital Action Cam User Manual Before You Start Declaration of Conformity Responsible Party JK Imaging Ltd Address 1411 W 190th Street Suite 550 Gardena CA 90248 USA JK Imaging Europe 71 Clarendon road Watford WD17 1DS UK Company Website www kodakpixpro com For Customers in Canada This device complies with Industry Canada license exempt RSS standard s Operation is subject to the following two conditions 1 This device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device For Customers in Europe C ECE mark indicates that this product complies with the European requirements for safety health environment and customer protection CE marked products are intended for sales in Europe This symbol crossed out wheeled bin WEEE Annex IV indicates separate collection of electrical waste and electronic equipment in the European countries Please do not throw the equipment into domestic refuse Please use the return and collection systems available in your country for proper safe disposal of this product For Customers in the U S A This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipmen
15. am and align the screw on the base to the Tripod Socket of the action cam Rotate the screw for fixing 2 Tie one end of the tether to the plane support small and the other end to the rear cover shaft of the action cam dQ 3 Assemble the base pre tightening handle and plane support large according to the direction illustrated in the Picture First press the base into the plane support large and then rotate and tighten the pre tightening handle Base br re tightening Handle Sf Support Large 4 Tack the double sided adhesive at the bottom of the plane support large and the plane support small to the object to be used Double sided adhesive is disposable It can be purchased separately and replaced if needed Head strap mount accessory applicable to mount the action cam on your head Location Pole Installation Method 1 Insert the angle bracket into the mount align the location pole on the angle bracket to the location hole of the action cam and align the screw on the angle bracket to the tripod socket of the action cam Rotate the screw for fixing Angle Bracket mount Screw Band 2 Set the band to your head and adjust the degree of tightness If you need to remove the mount please use one hand to push forward the angle bracket as directed by arrow and use a pointed object to push the buckles in the two side holes by order with another hand as directed by arrow T
16. ar after 2 seconds The message will disappear after 2 seconds The message will disappear after 3 seconds Message Description When turning on the product or pressing the product detects that the internal memory is out of space Updating firmware The memory card still cannot be recognized after format An error occurs when reading the memory card Interruption logging problem is encountered in the period of writing in the memory card or recording in the video recording or shooting process Reset Mode The message will disappear after 3 seconds User should do nothing The product will turn off automatically after the update is completed The message will disappear in 2 seconds and the screen of format or not will appear The message will disappear in 2 seconds and the screen of format or not will appear Return to the viewfinder status will be displayed in 2 seconds Message Description Reset Mode SS The internal memory still cannot be recognized M The message will disappear after format in 2 seconds and the screen Interruption logging problem is encountered of format or not will appear in the period of writing in the memory card or Return to the viewfinder recording in the video recording or shooting status will be displayed in 2 process seconds When a memory card lower than Class 4 is used to record a HD or above movie the writing speed is too slow and recording will not con
17. arkings on the battery compartment Never force it into the battery compartment If battery fluid leaks into the product please contact your retailer If battery fluid leaks onto your skin rinse your skin immediately with clean water and seek for medical attention To prevent the battery from being damaged do not drop the battery impact it with heavy objects or scratch it with sharp objects Do not let the battery come in contact with metal objects including coins to avoid short circuiting discharging excessive heat or possible leakage Do not heat the battery or throw it into a fire to avoid a possible explosion When the product is stored for a long period of time please remove the battery Do not store the battery in a hot environment In colder environments the performance of the battery may be noticeably reduced Do not attempt to disassemble the battery Disposal of used batteries should be carried out in accordance with the local national or regional regulations Memory Card Notes The memory card referred to in this manual is Micro SD Card or Micro SDHC card Please buy a genuine memory card of a well known brand Please keep the memory card clean and dry When inserting a memory card make sure the notch direction of the card matches the notch direction of the memory card mark near the card slot Do not force the memory card into the card slot Before using a brand new memory card
18. aving enabled state a prompting message about breaking of wireless connection in 30 seconds will be popped up when video recording on the smart device At this moment if the user does not stop video recording wireless online will be automatically disconnected and the wireless disconnection message will be displayed while video recording is continued on the action cam Shooting mode Shooting mode method of operation 1 Click icons at the top of the interface to set corresponding parameters 2 Click O to shoot photos 3 Click to enter the index playback state gt A CH 23 30 Gram ES aan NP 9999 alte enter the index playback state on the action cam shoot photos 0 TD switch to the video mode from the shooting mode Click About in the APP Home so that the version of the APP can be checked Connection Port Introduction Connect a Computer The product can be connected to the The product supports Windows operating computer using a USB cable to allow for systems Windows XP Windows Vista copying the files from the product into the Windows 7 and Windows 8 and the Mac computer operating system Steps 1 Open the rear cover of the product connect one end of the USB cable to the computer the computer needs to be in on state and the other end to the USB port of the product 2 The product display will show a rolling connection cartoon The computer will
19. d The rear cover will click when tightly closed Finally move the rear cover lock to the left Memory card refers to Micro SD card or Micro SDHC card is optional which is not included in the product package and needs to be purchased separately Please purchase a genuine memory card with a storage capacity range of 4GB to 32GB in order to ensure the safe preservation of data It is recommended to use a memory card of Class 4 or higher To remove the memory card please open the rear cover and gently push the memory card After it is ejected remove the card carefully The product will automatically turn off if the memory card is inserted and extracted when the product is on Charging Please charge after the product is turned off 3 You can also connect the product to your 1 Connect the product to the AC adapter compute witht a USB cable t0 Charge te with a USB cable battery If you press and hold the power l button during charging to turn off the 2 Then insert the plug of the AC adapter to product the charging will be stopped the power outlet for charging Charging indicator Ja m 5 gt g Red flash Charging S The indicator will go out once charging et is finished and the Action Cam will be powered off automatically IS To have maximum battery life charge the battery for at least 4 hours the first rs time After the battery is stored for a long l period use the supplied
20. d after switching to the index interface of the smart device and the downloading progress bar will be displayed In the index playback interface of the action cam click Bi to enter the download mode Select a file to begin downloading A downloading Only choose at most 20 files at the same time db wait downloading the download is complete In the index playback interface clicking Oo or lt will pause downloading cancel download Download will restart when the playback interface appears again fail in downloading Delete function 1 In the index playback interface of the 2 In the index playback interface of the action cam click to enter the selection smart device click to enter the interface select the files to be deleted selection interface select the files click D again to delete the files and needing to be deleted click Ff to delete select whether or not to delete in the the files and select whether or not to delete prompting interface delete in the delete prompting interface al GH 23 30 T all GH 23 30 lt 2 Items selected Olio sl lei SE EI 7 Items selected The files which are being downloaded No select box is displayed on the file and wait downloading cannot be which is being downloaded deleted Slide play function 1 In the index playback interface of the smart device click fa to enter the selection interface 2 Firstly select the files to be pla
21. d the memory card When opening the rear cover if there are water drops on the contact surface between the inside of the rear cover and the body please dry the water drops After using the product in water or near sand mud or other foreign materials please rinse it with clean water close the rear cover when cleaning After cleaning dry the product with a clean dry and lint free cloth If there is dust sand or other foreign materials on the waterproof rubber of the rear cover and its contact surface please wipe it with a clean dry and lint free cloth as soon as possible Before using the product underwater make sure that there is no damage to or foreign debris on the waterproof rubber gasket Then close the rear cover tightly to ensure the waterproof capability of the product Waterproof rubber with scratches and cracks will allow water to penetrate into the product Contact customer service immediately for maintenance with replacement of new waterproof rubber Rear Cover Waterproof Rubber Battery Notes Use only the battery specified for this product If the battery overheats during charging or use stop charging or use immediately Turn off the product remove the battery carefully and wait until it cools down Please keep the battery contacts clean and dry Please install the battery according to the positive and negative m
22. e TV while in the off state press and hold and to power on The product will automatically enter the playback state Specifications Design and specifications are subject to change without notice Active Pixels 14 24 Megapixels Total Pixels 15 31 Megapixels 1 2 33 MOS Lens Construction 6 groups 6 elements Still Image Exif 2 3 JPEG EES Ti Movie Format MOV H 264 Audio Linear PCM Stereo Focusing Range Normal 60cm e Field of View Ultra Wide Medium Narrow Water Ring 4 3 14MP 4320x3240 Still Size 16 9 10MP 4320x2432 5MP 2592x1944 Image Dimensions 1920x1080 30fps 1280x960 50fps 1280x960 30fps Movie Size 1280x720 60fps 1280x720 30fps 848x480 60fps High Speed Movie 848x480 120fps Detection Features Face detection Waterproof Feature Up to 10 m underwater Shockproof Feature Up to2m Dustproof Feature Equivalent to JIS IEC IP6X LCD Screen 1 5 inch 115k Pixels ISO Sensitivity Auto 100 800 Exposure Metering Method Artificial Intelligence AE AiAE Face AE Exposure Control Method Program AE Burst Shot Supported Playback Modes Single Photo White Balance Auto AWB Daylight Cloudy Fluorescent Underwater Internal Memory Approx 100 MB Storage Media a Micro SD Micro SDHC Card Up to 32GB Support MMC Card not supported Support 27 languages English Chinese simplified and traditional Japanese Language Korean French Spa
23. ector into the bottom part of the fixing sleeve and then tighten them with screw Fixing slee SES lt Connector 3 Assemble the base pre tightening handle and bar clamp according to the direction illustrated in the picture First press the base into the bar clamp and then rotate and tighten the pre tightening handle Gp Pre tightening Handle Suction cup mount accessory applicable to be attached to the automotive windshield or smooth surface Installation Method 1 Align the location pole of the base to the location hole of the action cam and align the screw on the base to the Tripod Socket of the action cam Rotate the screw for fixing 2 Assemble the base pre tightening handle and suction mount according to the direction illustrated in the Picture First press the base into the suction cup mount and then rotate and tighten the pre tightening handle a Base S Pre tightening Handle 3 First clean the suction mount and the windshield and then attach the suction cup to the windshield or smooth surface Press the handle to make it attached to the windscreen Suction Mount Handle Vented helmet strap mount A accessory applicable to bicycle helmet Installation Method 1 Expand the band first and then thread both ends of the band into the helmet 2 Thread both ends of the band into the buckle and then press the buckle clamp Buckle Clamp 3
24. ed and then restart the product You ll find the Loop recording function is still enabled Field of View Field of View means the image receiving angle for the product There are 4 options in Field of View meng Ultra Wide res Medium Pert Narrow Water Ring Field of View method of operation 1 After selecting the Field of View angle press to return to the viewfinder status LCD will display corresponding icons 2 Press to start recording 3 Press again to finish recording Medium or Narrow can only be selected when the Movie Size is set to 1080p30 If a Movie Size other than 1080p30 is selected under Medium or Narrow status the product will automatically set the Field of View to Ultra Wide Motion detection Motion detection means that if the product detects moving objects entering into the LCD screen it will automatically start recording During the recording process if there is no moving object detected for 10 continuous seconds the recording will be automatically paused There are 2 options in Motion detection By Off e IAN Enable Motion detection method of operation 1 After the Motion detection is enabled press L to back to the viewfinder status LCD will display corresponding icons 2 Press e if the product detects moving objects it will automatically start recording 3 The product will stop recording when there is no change in the image within 10seco
25. ed on the Copy to Card interface Reset Settings Reset Settings can recover all product settings to the factory defaults There are 2 options in the Reset Settings e X Cancel e Y Confirm FW Version The following operation needs to be followed FW Version can display the current version to update the firmware 1 Enter the FW Version interface and press x to enter the tertiary level menu Update the firmware LCD When a new version is stored in the memory card the firmware can be updated There are 2 options in Update will display New version X XX l al firmware J 2 Select W and press to confirm The X Cancel product will start to update 3 Whether the update is successful or e wi Confirm failed the product will automatically shut down Fe Update Firmware l If the low battery warning is displayed New Ver charge the battery before updating the X XX firmware Introduction to Mode Settings 2 options in the Mode Settings ofthe Mode Settings method of operation E ESEEERE 1 After selecting pp or options press e En Movie for recording movies COMMU 2 Press to enter the viewfinder status e T Still for shooting photos and display your selected Ty or e status Under the viewfinder status directly press oe to perform Tu or 6 status switch _ Movie Settings Introduction There are 8 options in First Level menu Movie Settings Movie Size
26. eeeeeeeeeeeeeeseeeeeeeeaeeeeeeeaeeeeeeseeeeeeeas 38 Introduction to Mode Settings ccceccececeecseeeeeeseeeeeeseeeeeeeeeaeeeeeeseeeeeeeseeeeeees 43 Movie Settings Introduction ccccccceeeeceeeeeeeeeeeseeeeeeeseeeeeesaaeeeeeseaeeeeeaaeeeeeeaes 44 Still Settings Introduction ceeccccceeeeececeeeeeeeaeeeeeeeeaeeeeeeseeeeeeeseeeeesseaeeeesaaaees 51 AP Settings NMOCUCUON E 54 smart Device APP Operating Method 57 Position cervice FUNCION scxasisecveiant cas sranie aa a E peia A e a N 57 e alt 59 OW AG Me EE 59 Remote VICWIING SM eege eege EE eg 69 PON EE Connection Port Introduction cccccecseeeeeeeeeeeeeeeeaeeeeenees 73 Connect a Computer 73 HDMI Connected TV Output 75 elauter 16 EIERE EE 76 Prompts and Warning Messages 19 Trouble VO OU e EE 83 Special ACceseories 85 a Accessories Included Your product box should contain the product you purchased along with the following accessories If anything is missing or appears to be damaged please contact your retailer Based on sales in different countries or regions the shape of the AC adapter will vary The actual product will prevail E SS GF Quick Start Guide Service Card Warranty Card Rechargeable AC Adapter USB Cable Li ion Battery B Standard Lens Cover Underwater Lens Cover Standard Lens Cover has been installed on the product when leaving factory Part Names 7 89 10 11 V
27. ery has been depleted SS Charge the battery If the files or folders have reached the maximum number 9999 for files 999 for folders the memory card cannot be accessed When a memory card lower than Class 4 is used to record a HD or above movie the writing speed will be slower and recording will not continue The number of pictures or folders in the memory card exceeds the specifications so the playback cannot be displayed or played back by date Battery overheat ES Copy the data to the computer disk and format the memory card using the product Use a higher class memory card or format this card before shooting Delete unwanted files Remove the battery when the product is turned off Continue to use the battery when it cools Android User Notification To ensure proper playback of video files created with the KODAK PIXPRO SP1 Digital Action Cam we suggest using the MX Player application 1 Download and install MX Player to your Android smart devices Download link https play google com store apps details id com mxtech videoplayer ad Run MX Player Choose Decoder under Settings and check the options as shown in the pictures The following video applications will also work VPlayer VLC for Android BSPlayer Free Settings Decoder Decoder List SOFTWARE DECODER j ER S W decoder locali Plaver Use H decoder Leederen Mek ebe rad oe usta S W decoder network s t bier decode as
28. ff the product OK Button Photo file no action Pause Normal speed Continue to Movie file start playback playback play back Menu Button Previous Playback Button Direction Button Lower Nest ENS Next Frame Video Recording Button Shooting Button Enter viewfinder status No action Turn On Off Turn on When the power is off press and hold for more than 2 seconds to turn on the product or press and hold for more than 2 seconds to turn on the product and enter the playback status Turn off When the power is on press and hold for more than 2 seconds to turn off the product If the product cannot be turned on off normally you can remove the battery for forced power cut Set your Language Date and Time after the first power on 1 Press and hold the to turn on the product and enter the language selection screen 2 Press amp or to select language 3 After pressing od button to select desired language the product will enter Date Time setting screen Press Si or to adjust the date and time display format and press oe to confirm the display format 5 In the date and time options press Si or to adjust the values and press to confirm 6 After confirming automatically go to and press to confirm and enter the viewfinder status gt Date Time Le 2013 07 42 HEM LCD Screen Display D T O TE e NI we
29. finder status LCD will display corresponding icons 2 Press to shoot When the image size is set to 5MP Medium and Narrow cannot be enabled White Balance White Balance means that the user adjusts the color temperature under different light sources to ensure that the colors are reproduced correctly There are 5 options in White Balance e H AWB Auto White Balance ZE Daylight e XJA Cloudy e fl Fluorescent e E Underwater White Balance method of operation 1 After an option of the White Balance is selected press to return to the viewfinder status LCD will display corresponding icons 2 Press to shoot AP Settings Introduction The action cam can be wirelessly connected with your smart device Please review the following items before your first connection 1 Your smart device system version needs to be iOS 4 or higher and Android 2 3 or higher If not please upgrade your smart device system version Please do not use in places having high intensity magnetic field electrostatic and electric wave interference for example near a microwave oven which may cause failure in receiving signals Please maintain a distance between the action cam and the smart device less than 10 meters 32 8 feet without signal shielding interference Please do not use wireless connection functionality on a plane sP 6 The action cam and the smart device can only be c
30. he files on the smart device RA share e slide play RES edit e CH delete Edit function 1 Editing photo files Click B to enter the effect interface where filter effects brightness adjustment and modeling effects can be set e Filter effects The filter effects are divided into 23 types More effect options can be viewed by sliding the effect option bar from side to side F al GH 23 30 Effects ei ei ant 4 EEE ot Effect option bar e Brightness adjustment effects R off LAY ima Auto e Modeling effects CO off O centering on dot A centering on strip lateral direction First click the effect your like and then click Android system IOS system to select the options of saving or uploading to social networks or cancel 2 Editing movie files Click B amp to enter the trim interface Quick browse bar e and gt play movies e L i increase the number of frames e shorten the number of frames M trim starting point Mp trim finishing point Steps of movie trim According to the desired trim accuracy of the movie click or to increase or shorten the number of frames Slide the quick browse bar from side to side so that the vertical line stays on thumbnails needing to be cut and click JN to select the trim starting point Gi Slide the quick browse bar aga
31. hen remove the angle bracket out from the mount 2 t Extended Arm You can add one or two extended arms except head bank mount to each kit to help you to adjust the mounting angle of the action cam more flexibly Extended Arm The Kodak trademark and trade dress are used under license from Kodak 2013 by JK Imaging Ltd All rights reserved JK Imaging Ltd 1411 W 190th Street Suite 550 Gardena CA 90248 USA JK Imaging Europe 71 Clarendon road Watford WD17 1DS UK www kodakpixpro com Ver 6
32. ideo Recording Button Shooting Button Status Indicator Menu Button Direction Button Upper 10 Power Button Delete Button 11 Lens Cover Buckle 12 OK Button Playback Button Je Direction Button Lower 14 Tripod Socket 15 Location Hole 16 Rear Cover Open Switch Rear Cover Lock Installing and Dismantling the Lens Cover Two types of replaceable lens covers are Steps for dismantling the lens cover provided for the product 1 Hold the product with your left hand and Standard Lens Cover pull the lens buckle with your finger to the left end as illustrated in the picture Hold the lens cover ring with your right hand and rotate to the OPEN arrow direction Applicable for general use Do not use underwater Visual angle in the air is about 160 Will not 2 When three alignment points are in a focus underwater straight line loose your left hand from the lens buckle and remove the lens cover from the right with your right hand Alignment Points Underwater Lens Cover Applicable for use in water Visual angle in the air is about 130 and visual angle in water is about 90 Steps for installing the lens cover 1 Hold the product with your left hand and pull the lens buckle with your finger to the left end as illustrated in the photo hold the lens cover ring with your right hand When three alignment points are in a straight line buckle the lens cover
33. in to the left so that the vertical line stays on the thumbnails needing to be cut and click Mp to select the trim finishing point GO Click Android system iOS system to select the option of save or uploading to social networks or cancel Remote Viewfinder Click Remote Viewfinder in the APP Home to enter the viewfinder status and control the action cam to shoot by using the smart device The files shot through the APP are saved in the action cam The setting parameters of the action cam are displayed at the tops of the video mode and the shooting mode interfaces on the smart device Movie Size 1080p30 960p50 960p30 720p60 720p30 WVGA60 WVGA120 Field of View AWB Still Size Burst Shot cam Bme Ultra Wide m Medium Deeg Narrow Water Ring ATD AWB ZE Daylight ZA Cloudy oe Fluorescent Zo Underwater 14M 10M 5M Single Burst Shot The characteristics of these parameters are the same as the action Video mode 99 99 R S enter the index playback state on the action cam start video recording stop video recording switch to the shooting mode from the video mode Video mode method of operation 1 Click icons at the top of the interface to set corresponding parameters Click to start video recording and click o to stop video recording Click BJ to enter the index playback state In Wireless Power S
34. ing 1 Enterthe Date Time in the secondary level interface and press Loi to confirm 2 Press amp or to adjust the date and time display format and press to confirm the display format 3 In the date and time options press amp or e to adjust the values and press oi to confirm 4 After the setting is completed select S and press to confirm and back to Date Time in the secondary level interface 5 Press to return to the viewfinder status Language The language can be set during the first power on cycle If you wish to change the language thereafter please operate as the following 1 Enter the Language in the secondary level interface and press ol to confirm 2 Press amp or to select language 3 Press x to confirm and back to Language in the secondary level interface 4 Press to return to the viewfinder status Format Format can clear all data stored in the memory card or memory including protected movies and photos There are 2 options in Format e X Cancel ef Confirm When a memory card is inserted only the card can be formatted If you need to format the internal memory remove the memory card first Copy to Card Copy to Card is to copy the files in the internal memory to the memory card There are 2 options in Copy to Card e X Cancel e SY Confirm When the memory card cannot be detected by the product options will not be display
35. may be reproduced transmitted transcribed stored in a retrieval system or translated into any language or computer language in any form by any means without the prior written permission of JK Imaging Ltd E Al trademarks mentioned in this manual are used for identification purposes only and are properties of their respective owners m This manual provides you with instructions on how to use your new KODAK PIXPRO Digital Action Cam Every effort has been made to ensure that the contents of this manual are accurate However JK Imaging Ltd reserves the right to make changes without notice SS Throughout this manual the following symbols are used to help you locate information quickly and easily Indicates useful information Indicates precautions are to be taken while operating the product E In this manual digital action cam is referred to as action cam Safety Notes Waterproof Dustproof Shockproof Freeze proof JIS IEC waterproof grade 8 IPX8 JIS IEC dustproof grade 6 IP6X Height for shockproof rating is 2 0m Suitable temperature range for freeze proof capability is 10 C and above Product Notes Do not disassemble or repair the product by yourself Do not heavily drop or knock this product Improper handling may damage this product Avoid touching the lens cover and lens element please use professional lens cleaning paper together with lens cleaning agents to wipe the lens and keep the
36. n to the viewfinder status When the memory card is inserted only files in the memory card will be displayed files on internal memory will not be available to display If there are no files in the memory card or internal memory a no image warning window will appear Movie Playback 1 Select movie to be played back and press ol to start movie playback 2 When playing back the movie an operation guidance will appear on the screen You can press buttons to perform the corresponding functions Press j Movie playback rewind multiple presses will fasten the speed x2 x4 x8 x16 Press Movie playback forward multiple presses will fasten the speed x2 x4 x8 x16 Press ol Under normal playback mode the movie playback will be paused under the forward rewind or pause status normal speed playback will be recovered Press Movie playback back to the initial state Movie playback rewind or forward 00 00 47 Movie playback pause There will be no sound output during rewinding or forwarding Movie or Picture Delete 1 Select the movies or photos to be deleted and press to enter the Delete screen Press or gt to select Delete and press to confirm 2 After a movie or a photo is successfully deleted the LCD will display the next movie or photo If you wish to delete additional files please continue per item 1 above 3 If you want to exit the Delete screen select Exit and
37. nds 4 When the image changes again the product will start recording automatically and this time it will regenerate a video file 5 During recording you may press the When the memory card is full will to stop recording become red font and flashes for 2 seconds When the Motion detection feature D A is enabled Time Lapse or Loop 15 00 recording setting cannot be performed Movie Size cannot be selected as WVGA120 Motion detection interface icon _ Indicates the total time of recording Indicates the time of the product GI Indicates the total time from the beginning of recording Wind Cut Wind Cut refers to the reduction of noise caused by wind There are 2 options in Wind Cut e RQ Off lt 9 Enable Wind Cut method of operation 1 After the Wind Cut is enabled press to return to the viewfinder status LCD will display corresponding icons 2 Press to start recording 3 Press e again to finish recording White Balance White Balance means that the user adjusts the color temperature under different light sources to ensure that the colors are reproduced correctly There are 5 options in White Balance EP AWB ZE Daylight e SA Cloudy e one Fluorescent Underwater White Balance method of operation 1 After the White Balance is enabled press to return to the viewfinder status LCD will display corresponding icons 2 Press to start
38. nish Portuguese Thai Indonesian Vietnamese Italian Support German Dutch Russian Polish Swedish Danish Finnish Norwegian Greek Turkish Hungarian Croatian Czech Arabic Hindi USB 2 0 Micro 5 pin USB HDMI Type D Power supply Rechargeable Li ion Battery LB 080 3 6V 1250mAh In action cam Charging Battery Approx 350 Shots Based on CIPA Standards Approx 130 min for Video Performance 1080p 30fps Temperature 10 40 C Humidity 0 90 Environment 84 7x51 4x39 5mm Based on CIPA Test Standards Weight Approx 155g Approx 155g excluding battery and memory card battery and memory card Prompts and Warning Messages Message Description When using Copy to card if the number of folders in the memory card exceeds the maximum number of folders 999 the copy and access actions cannot be performed This message indicates that a long read time may be caused due to too many folders in the product During shooting if the files or folders have reached the maximum number 9999 for files 999 for folders the memory card cannot be accessed When the file is protected the message will appear on the screen if the delete action is performed When turning on the product or pressing the product detects that the memory card is out of space Reset Mode End the message after the product processing End the message after the product processing The message will disappe
39. o save power Pressing will turn on the LCD and immediately initiate terminate recording Pressing any other button will only turn on the LCD dQ LCD Screen Display under Playback Status NES Grp a 2m Gi AUTO S WO 00 01 23 AVIS OPA 441 13 OOO rss 14 ZAAR OZA 1247 41 White Balance Display 2 Wide Medium Narrow Water Ring 1 Movie Display 10 2 Field of View Display 11 Time Lapse Display AH D Et Er ee 2 7 A 7 oe Geel Geel C20 E UE NU SL CG S 1i Oyo SS S we CG 9 IN 10 WB ZOS Su 5 Tal CG 11 SAS a a O Some icons will automatically hide after a 2 second display Only displayed when playing back the movie file E Indicates 16 9 display range 3 Memory Card or Internal 12 Display of Current number Memory Display of Shots Total Number of 4 Battery Status Display Shots 13 Movie Time Length 5 L ding Displ ge Se isplay Display SES 14 Shooting Time and Date 7 Movie Size Display Display 8 Still Size Display co I Indicates 4 3 display EJ Motion detection Display range Introduction to Basic Operation of Playback Single Photo 1 When in viewfinder status mode press to enter the playback status of video and pictures 2 Display movie or picture files on the LCD screen 3 Press amp or to view the movies or pictures stored in the memory card or internal memory Press to retur
40. onnected one to one When the temperature of the battery is higher than 68 C AP setting cannot be enabled Wireless connection will be automatically disconnected Connection setting method of the product and the smart device Step 1 setting up the product 1 Press in the viewfinder status select AP Settings and press x to enable wireless connection function so that the SSID interface in AP mode appears SSID and WPA2 password messages are displayed in the interface AP mode SSID PIXPRO SP1_ 1234 WPA2 PSK 12345678 Z O Zor Wireless connection process takes about 30 seconds At this moment except for other buttons are deactivated Step 2 setting up the smart device 1 Enable the wireless function of the smart device to search surrounding wireless devices 2 Select the name of the action cam to be connected PIXPRO SP1_XXXX and input the eight digit digital password displayed next to WPA2 PSK on the action cam 3 Download the special APP installation package APP name PIXPRO SP1 from the device appropriate APP store and install 4 Click the icon of the APP to enable the APP Step 3 set up completion 1 Once the APP is connected to the action cam functional operations can be enabled on the smart device If there is a need to interrupt the connection press 0 so that the selection interface appears select Y press interrupt connection and re
41. press to confirm Geh Delete Exit Movie and or pictures cannot be restored after being deleted A protected file cannot be deleted Rotation The direction sensor comes with the product can automatically adjust the direction during file playback according to the rotating direction detected during shooting in order to ensure that what you see are positive images The direction of rotation refers to the direction rotating around the lens center clockwise or counterclockwise Only when the direction sensor detects that the product has rotated for 180 the rotation feature is effective Rotation of 90 or 270 is invalid The product will record the detected 180 rotation information in a file When you use a player supporting rotation tag identification Such as Quick Time for playing the image can be automatically converted to positive Introduction to the Setting Mode of Menu Options 1 Under the viewfinder status press G to enter first level menu interface of the menu Press amp or to select Mode Settings Movie Settings Still Settings AP Settings and General Settings N 3 Press x to confirm and to enter the corresponding secondary level menu interface 4 Select items with on the secondary level menu and press ex to confirm and to enter the tertiary menu interface a Select Movie or Shot or Exit in the secondary menu and press confirm to back to the fir
42. rompt whether to not PIXPRO SP1 would like to use your current location if the position service is disabled it will prompt Turn on Location Services to allow PIXPRO SP1 to determine your location and if clicking setting the smart device position service setting interface will appear 2 When the APP is enabled for the second time or later status of position service Basitioneenica The second time or later enabling of the APP state selected at the first time The position service is Sp SECH enabling of the APP enabled The position service is Off A prompting message Turn on Location Services to allow PIXPRO SP1 to Enable the position determine your location will appear and service if clicking setting the smart device position service setting interface will appear A prompting message that Location Service is disabled Please enable Location Service for PIXPRO SP1 and if clicking OK the APP home interface will appear Besides the position service will be automatically disabled APP Home Playback Enter APP Home interface and three options are displayed e Playback enter playback state e Remote Viewfinder enter the viewfinder status and control the action cam to shoot by using the smart device e About check the version of the APP In the interface of the APP click lt to return to the previous stage of interface But in index Playback and Remote Viewfinder states click
43. st level menu interface In the menu interface except for the Wireless connecting status press to return to the viewfinder status Menu Introduction Loop recording Field of View Field of View White Balance Level Sound Settings Menu Wind Cut White Balance Exit Introduction to General Settings 10 options in the General Settings of the Sound Settings first level menu There are 4 options in the Sound e Sound Settings Settings Power Off Cp Volume 1 e Wireless Power Saving CB Volume 2 Date Time CH Volume 3 e Language Ch Off Format Power Off e Copy to Card Power Off means the product will automatically shut down after 60 seconds Reset Settings after the LCD is off e FW Version There are 2 options in Power Off Exit dr off e M 60 seconds E The Power Off will be invalid during recording movie playing back and wireless connecting Wireless Power Saving Wireless Power Saving mode means that after 30 seconds of remote controlled recording with the APP the wireless connection will automatically disconnect but the product will continue to record Wireless power saving mode will prolong battery life There are 2 options in Wireless Power Saving Pon e EP Enable Date Time Date and time can be set during the first power on cycle If you wish to change the date or time thereafter please operate as the follow
44. t generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment About this Manual Thank you for purchasing this product Please read this manual carefully and keep it in a safe place for future reference E JK Imaging Ltd reserves all rights to this manual No part of this published manual
45. tinue E Cancel the message and return to the viewfinder status in 4 seconds The time of file processing imaging processing in synthesis in saving edition after processing archiving coping in Format and the like exceeds 2 seconds E The message will disappear after the operation is completed Description Reset Mode PS Connecting to the computer USB E The display is ended after E Connecting to the HDMI device connection is succeeded It will shut down after displaying for 2 seconds Mm A message appears to prompt updating after full charging and returning to the update screen E Caution will appear before power off when the battery of the product is already dead E The firmware cannot be updated when power is insufficient It will shut down automatically in 2 seconds and can be recovered to use only after the temperature is reduced E The message will be displayed when the temperature of the battery reaches 70 C during recording Return to the menu interface in 2 seconds and recover use only after the temperature is reduced E When the AP setting is enabled the message will be displayed when the temperature of the battery is in the range from 68 to 70 C Trouble Shooting Problem Product does not turn on Exceeded maximum folder number Writing speed of the memory card is slow Too many videos to process High temperature warning Possible causes Solution E The batt
46. to the lens and rotate against the OPEN arrow direction When the notch of the lens cover ring is aligned with the lens buckle loose your left hand from the lens buckle and remove your right hand from the lens cover Please select appropriate lens cover when taking videos and pictures otherwise it will affect the image effect When the product is exposed to fluctuations in temperature condensation may form on the inside surface of the lens cover If this happens remove the lens cover clean it with a soft dry lint free cloth and then reinstall the lens Installing Battery and Memory Card 1 Open the rear cover First set the rear cover lock to the right and push the open switch of the rear cover downward Then rotate the rear cover around the shaft direction to open 24 Insert the battery into the battery compartment according to the negative and positive directions as illustrated in the following picture 3 Insert the memory card into the card slot according to the direction illustrated in the picture when the product is turned off When inserting a memory card make sure the notch direction of the card matches the notch direction of the memory card over the card slot Do not force the memory card into the card slot CS AHA 4 Close the battery cover First rotate the back over around the shaft direction to close upwar
47. turn to the SSID interface 3 If there is a need to turn off wireless AP mode press button or press after E selecting rr in the SSID interface so that the selection interface appears Select W press to turn off wireless e EI BR E 2 If connect APP failed press ol to return to the SSID interface select press so that the selection interface appears select Y press x This will change the WPA2 password Next perform connection operation again on the smart device smart Device APP Operating Method The APP supports the position service function on your device It may record GPS information in the photo files This function is not supported for movie files Android system 1 When the APP is enabled for the first time it may prompt that PIXPRO SP1 would like to use your current location If the position service of the smart device is not enabled you may select whether to enable the position service or not according to prompting in the interface 2 When the APP is enabled for the second time or later if the position service function has been enabled already the interface will directly turn to the home page of the APP and if the position service function is not enabled you may select whether to enable the position service or not according to prompting in the interface iOS system 1 When the APP is enabled for the first time if the position service is enabled it will p
48. yed and then click 2 to start slide play 3 If no file is selected directly click 2 so that all files will be played F all GH 23 30 2 Items selected Clicking a photo in slide play will stop slide play and the single photo interface will appear When playing movie in a slide only the first frame is displayed clicking the movie will stop slide play and the movie play interface will appear Share function 1 In the index playback interface of the Transmission procedure is determined smart device click to enter the according to the settings of the smart selection interface device 2 Select the files to be shared and click W i to pop up the share option Ke 23 30 lt 2 Items selected Wl Ze Je d AN a ere IS Single Photo 1 Executable operations in single photo In the index playback interface the single playback of the files at the action cam photo interface will appear if a single file is SES clicked e enter the viewfinder status Previous and next files can be selected to dh E E EEN be browsed through sliding from side to cana nie ihe eman device side 100 enlargement screen will appear by j g delete double clicking one single photo and the original dimension will be recovered by double clicking again iOS system interface has one more function than the Android system A I start play pause play Executable operations in single photo playback of t
Download Pdf Manuals
Related Search