Installation Instructions & Owners Manual
Contents
1. herein must be performed by a licensed electrician using approved methods and materials according to the local code governing the installation site General Electrical Notes Each cabinet should be wired to a SEPARATE 15 Amp circuit Unless otherwise specified ALL WIRING supplied by the contractor must be APPROVED 12 Ga AWG Disconnect device must be provided in the branch circuit by electrician You have the option of wiring a fluorescent light in this cabinet Please contact a licensed electrician for consultation Rev 100308 6072 0 eH 18 117 FLOOR MOUNT BRACKETS IMPORTANT NOTE PLUMBING LOCATIONS SHOWN ARE TYPICAL FOR CURRENTLY AVAILABLE THE PLUMBING HARDWARE IS NOT SUPPLIED WITH THE SYSTEM IS BEING INSTALLED WE RECOMMEND YOU REVIEW THE TEMPLATE SUPPLIED BY THE DELIVERY COUNTER TOP 1 2 NPT 1 1 8 TO 1 3 8 DIFFERENCES IN SYSTEM HARDWARE EXACT FLOOR LOCATIONS MUST INSTALLER x 6 FLOOR TEMPLATE PLUMBING LAYOUT DETAIL OF AIR WATER AND VACUUM STUBS STOP VALVES SUPPLIED WITH CABINET 9 094 I9polN alelduuel Joold2. to Both leveling the cabinet and mounting to the floor may be done at a later time but be sure to do so before access to the feet floor brackets is unavailable prior to reinstalling covers and panels Cabinets placed up against a wall is one case where you should wait to mount the cabinet to the floor Step 8 Make electrical connections per the ECO 6 Electrical Schematic amp Instruction sheets NOTE Cabinets placed against a wall must have electrical access cut through the rear base or Lower Rear Panel Assembly Instructions Model ECO 6 Step 9A Optional Mount the BDS 2571 Assistant Vacuum Package shown underneath the sliding countertop using 4 10 24 x 1 1 4 allen screws using 5 32 Allen Wrench see Figure 6 Attach connections according to the unit manufacturers directions Step 9B Optional Mount the BDS 2564 Doctors Control Package not shown underneath the sliding countertop using 4 10 24 x 1 1 4 allen screws using 5 32 Allen Wrench Attach connections according to the unit manufacturers directions Step 10 Install Upper Lower Back Panels A4 amp A5 by securing 4 Allen Bolts A6 to each panel using a 4mm Allen Wrench see Figure 7 Step 11 Install 4 Shelves D3 2
3. 308 Hinge Adjustments Model ECO 6 Adjustment Instructions for Concealed Hinges and Drawers 3 Dimension Adjustment for Snap On Hinge Note Remove Cover Cap Allows for three way adjustments in the hinge arm The side adjustment is a micro adjustment The depth and height adjustment is held by a grid system Release Latch Use 2 POZIdrive screwdriver to adjust screws 1 Side adjustment 2 Depth adjustment 3 Height adjustment Adjustment for Drawer 1 Height adjustment Loosen screws B slightly Adjust screw A adjustment 2mm Tighten screws B 2 Side adjustment Loosen screws B slightly Adjust front to required position adjustment range 1 5mm Tighten screws B Rev 091908 Assembly Instructions Model amp ECO 6 Component Identification A Lower Cabinet Lower Back Panel Upper Back D Upper Storage Note Back Panels Item B amp C attached to Lower Cabinet Item A during shipping Rev 100308 Assembly Instructions Model ECO 6 Step 1 Check the incoming power location to see if it conforms to the specification on the floor template drawing If a dental delivery system is to be installed on this cabinet confirm that the appropriate air water and vacuum plumbing stubs are in place Step 2 Remove 2 Doors A1 and 4 Drawers A2 from Lower Cabin
4. Installation Instructions E Series Dental Cabinetry amp Owners Manual Model ECO 6 L1 selbonomtt 1631 Dr Martin Luther King Drive Consumer Please retain these instructions for future use St Louis MO 63106 314 231 7383 888 833 3682 Fax 314 621 2296 www belmontequip com 806160 4 ISOMETRIC VIEW 4 17 3 4 9 094 I PON gt 2 5 20 3 8 FRONT VIEW RIGHT SIDE VIEW General Cabinet Handling Information Models ECO 6 Move by using some type of roller dolly slings or a comparable moving aid See Figure A and B Figure B Attention DO NOT lift by Sliding Top which could result in damage to the sliding mechanism Rev 090808 Surface Cleaning Model ECO 3 ECO 6 ECO Sys Cabinetry Systems Laminate Surfaces Cleaning Instructions The disinfectant solution should be applied in accordance with the instructions provided by the manufacturer The following solutions are recommended for laminate surfaces they may also be used on metal and glass surfaces Product Manufacturer Birex Biotrol International Kodak Clinasept Kodak Foaming Disinfectant Catalogue 829 5230 Belmont is not responsible for any changes made by the manufacturer in the chemical composition of the cleaning solutions listed above which may affect the surface finish after application Rev 100
5. et A see Figure 1 Note Drawers must be kept in order and returned to original locations in order to properly fit Remove the 2 Bottom Covers A3 from inside Lower Cabient A see Figure 1 PULL LEVER TO RELEASE HINGE Step 3 Remove Upper Lower Back Panels A4 amp A5 by removing 4 Allen Bolts A6 from each panel using a 4mm Allen Wrench see Figure 2 Step 4 Move Lower Cabinet A to its desired location see General Cabinet Handling Information page for moving information Attention DO NOT lift by Sliding Top which could result in damage to the sliding mechanism Assembly Instructions Model ECO 6 Step 5 Remove 2 Doors D1 from Upper Storage D see Figure 3 PULL LEVER TO RELEASE HINGE Step 6 Place Upper Storage D on top of the Lower Cabinet A Secure with 4 1 4 20 x 1 3 4 Flat Head Screws D2 see Figure 4 Note Make sure to have an assistant hold the Upper Storage in position to keep it from falling off Step 7 IMPORTANT Adjust the 4 Leveling Feet A7 to the desired height using a 5mm allen wrench see Figure 5 You can mount the cabinet to the floor at this point by mounting the 4 Floor Mounting Brackets A8 to the floor using proper fasteners for the floor being mounted
6. on each side of Upper Storage D by installing 4 shelf pins per shelf into holes on inside panels see Figure 8 Step 11 Install Upper Storage Doors D1 to Upper Storage D see Figure 9 Install Door Handles D4 to Upper Storage Doors D1 using M4 x 25mm Pan Head Screws D5 see Figure 9 Step 12 Install 2 Bottom Covers A3 to inside Lower Cabient A see Figure 10 Install Shelf A7 in Lower Cabinet A by installing 4 Shelf Pins into holes on inside panels see Figure 10 Install 2 Doors A1 see Figure 10 Install 4 Drawers A2 see Figure 10 Step 13 Install Clock Timer A8 using double sided tape See Clock timer instructions for battery install and operation see Figure 11 Installation Complete Assembly Instructions Model ECO 6 Figure 10 Figure 11 Electrical Schematic Model ECO 6 ECO 6 ELECTRICAL CONNECTIONS ALL ELECTRICAL WIRING MUST BE DONE BY OWNER WITH LICENSED ELECTRICIAN DUPLEX fester RECEPTACLE _ to i ERE E u O B o J BOX w LB o i RECEPTACLE REAR OF CABINET Rev 091908 Electrical Instructions Model ECO 6 ECO 6 Electrical Instructions IMPORTANT NOTE Approved electrical components are used in the ECO 6 cabinet however the procedures described
Download Pdf Manuals
Related Search