TROUBLESHOOTING OF AQUEOUS COATINGS
Contents
1. Too much moisture in the sheet slows absorption of water from the coating into the sheet Coating feels tacky in the delivery A partial drum coating is being used Too much coating is being run ANCHOR SOLUTION Check and adjust IR output for correct load temperature Try stronger tighter body ink for more stability under coating Use faster drying coating but be cautious of cracking Store paper under controlled conditions or Only open packages before use Specify coating that does not contain solvents like butyl cellosolve Coating may have thickened Check viscosity and pH reduce as required or mix with fresh coating Check at trailing edge for excess bead and turn coater down PROBLEM BLOCKING OR SCUFFING IN THE DELIVERY continued SYMPTOM Heavy ink coverage will cause greater coating hold out and slower setting Very high gloss coating is being used N ot enough spray powder Ink coating not set well enough at delivery Load temperature is higher than the softening point of the coating Residual solvents are re softening set coating Solvents or alcohol substitutes are cooking out of heavy ink SOLUTION Use faster drying coating or run slower to allow longer set time Coating is softer and slower setting Compensate with more air or slower press speed Some coating jobs still require powder C heck setting Use faster se2. ink or tighter body Run as dry as possible to prevent over emulsification Use limited powder to prevent adhesion Reduce load height or rack loads Do not reduce viscosity Reduce coater speed to apply a thinner film Reduce coating viscosity by 5 seconds and test Reduce warm air supply Specify a medium drying speed coating PROBLEM RINGS OR RIDGES ON ROLLERS BLANKET OR SHEET SANDPAPER FEEL OF JOB SHEETS CURL SYMPTOM N ot enough pressure between roller and blanket N ot enough coating Spray powder is pushed into coating that is still tacky Stock is absorbing too much water from coating Excessive heat applied after coating SOLUTION Increase pressure and check for any low areas in roller or blanket Turn up coater or increase viscosity Increase warm air or run job slower Use faster drying coating Specify coating without solvents to reduce tackiness during drying Reduce amount of powder Specify a high solids coating to apply less water Check water content of stock If too dry stock can distort from large water pickup Consult with ANCHOR for more flexible coating Check for proper load temperature and do not exceed 105 F PROBLEM SHEETS CURL continued SPITTING OR SLINGING OF COATING THICKENING OF COATING SYMPTOM Mechanical distortion Image wrinkle or distortion Coating is building up on the ends of rollers Partial drum has
3. lost water or ammonia ANCHOR SOLUTION Use paper stock of 80 Ibs or higher Run the coating as near the edge as practical to provide a uniform size change in the sheet Check the setting of sheet guides for correct settings On heavy coverage reduce water pickup of the ink to minimize size change in stock Check that coating is at proper application temperature Check coating for proper viscosity Clean ends of rollers and check roller speed Keep drums closed when not in use Check that pH is 8 0 to 8 5 and add ammonia if required Reduce viscosity to original value Mix partial drum into fresh coating and adjust viscosity as needed PROBLEM UNEVEN COATING APPLICATION SYMPTOM Uneven pressure between rollers blanket and sheet Dried coating is causing defects Blanket or rollers have low spots SOLUTION Check roller settings blanket packing and impression cylinder pressure Adjust to kiss contact Clean rollers blanket and impression cylinder Check and replace as required
4. MPTOM Coating is soaking into paper or ink Level in reservoir pan is too low Air is being introduced into circulating system Recirculating pump is running too fast Ridges in the direction of travel caused by too little coating Coating is being pushed into the ink Viscosity is too low and coating is soaking into job Mottle only over the ink caused by poor wetting of coating SOLUTION Use sheet with better hold out Consult with ink manufacturer Apply heavier layer of coating if possible Specify coating that is resistant to dry back Increase coating level in pan Check seals on pump and lines for air leaks Eliminate free fall return into drum Reduce pump speed to just keep pan full Increase amount of coating Adjust blanket to back cylinder to kiss impression Reduce pressure to get uniform application Specify higher viscosity coating Check type and amount of wax or silicone in ink Limit to PE wax PROBLEM OFFSETTING OF INK ORANGE PEEL APPEARANCE SYMPTOM Too little coating to seal ink Heavy films of ink are setting too slowly to be stable Too little spray powder Excessive pressure from high loads Coating too thin Too much coating is being applied to lay smoothly Viscosity too high to flow out well Coating is drying too fast to flow out ANCHOR SOLUTION Apply more coating Specify fast setting ink stronger
5. TROUBLESHOOTING OF AQUEOUS COATINGS This guide is intended as an aid to help you solve problems in the pressroom with aqueous coatings The aqueous coating products being sold today are vastly improved from those of even a few years ago but the process of applying a water based coating over wet litho ink must be understood By following the suggestions outlined in this book and selecting paper ink and coatings that are compatible you will get consistently good results We hope that you will find this guide informative and instructive in the use of ANCHO R Brand aqueous coatings We carry a complete range of coatings and are always happy to discuss special requirements that you may have If you have any questions or comments please feel free to call or to write to us at Fuji Hunt Photographic Chemicals Inc 50 Industrial Loop North Printed in USA 10 02 O range Park Florida 32073 Copyright 1998 2002 All rights reserved No 800 354 2300 or 904 264 3500 portion of this booklet may be used or reproduced in www fujihuntusa com www anchorlith com ANCHOR whole or part without our written consent PROBLEM BACKTRAPPING OR INK ON THE COATING BLANKET SYMPTOM Coater activating late allowing ink to transfer to blanket at start Excess pressure between coating blanket and back cylinder causing thin coating application Too little coating applied to protect wet ink Ink does not set before coating Ink is pulled from shee
6. eed of ink run dryer use stronger tighter body inks Reduce wax use only PE wax or use NO W AX inks PROBLEM CRACKING OR ALLIGATORING OF COATING DURING DRYING continued CRAWLING FISH EYES OR PINHOLING OVER INK DRYING PROBLEMS IN THE DELIVERY EVEN THOUGH NOTHING HAS CHANGED FROM THE LAST JOB SYMPTOM Coating used is drying too fast compared to ink Coating being used is too hard brittle Coating is not wetting ink Defoamers silicones etc are migrating out of coating causing fish eyes Problems with drying equipment Job requirements amount of ink coating press speed paper hold out have exceeded dryer Capacity High relative humidity has reduced the ability of the dryer to remove water from coating SOLUTION Reduce setting on hot air knives Check with ANCHOR to add plasticizer or switch to more flexible coating Consult ink supplier about waxes being used in ink Coating does not contain adequate wetting agents Consult with ANCHOR Consult with ANCHOR for lab test of coating Check output of lamps warm air knives ensure exhaust is not restricted Switch to faster drying coating Minimize ink film thickness Reduce coating weight Adjust warm air knives for maximum output Reduce press speed Increase warm air knives to compensate Use faster drying coating PROBLEM BLOCKING OR SCUFFING IN THE DELIVERY Slow drying over heavy ink coverage
7. t Ink is over emulsified reducing body Coating does not wet ink properly Blanket packing not trimmed correctly SOLUTION Adjust timing for coater start Adjust contact to kiss pressure Reduce pressure until coating does not transfer then tighten 0 001 Turn up coater or run at higher viscosity Check ink density decrease setting time use stronger ink Try increasing tack to provide better adhesion of ink Run as dry as possible decrease water pick up of ink Check with ink supplier about wax and discuss with coating supplier Cut packing sharply 1 4 inch smaller than sheet PROBLEM BUILD UP OF COATING ON BLANKET OUTSIDE OF SHEET BUILD UP OF COATING AT TRAILING EDGE OF SHEET CRACKING OR ALLIGATORING OF COATING DURING DRYING Improper adjustment between blanket and back cylinder Applicator roller set too tight to blanket Too much coating being applied Packing is not trimmed correctly Applicator roller is not at same speed as blanket Blanket and back cylinder are set too tight Thick ink film under coating is not stable Coating is not wetting ink properly ANCHOR SOLUTION Adjust packing to proper height Adjust for roller to kiss setting 1 to 2 mm Turn down coater Cut sharply 1 4 smaller than sheet Check roller speed and adjust packing to minimize speed difference Adjust for kiss impression to sheet Increase setting sp
8. tting ink or harder coating Reduce load temperature and compensate for heat given off during ink drying Reduce load height Specify coating with no solvents and minimize alcohol substitutes Run dryer and consult ink or fount supplier PROBLEM BLOCKING OR SCUFFING IN THE DELIVERY continued BLOCKING IN THE LOAD OR LATER DURING CONVERTING OR STORAGE COLOR SHIFTS WITH REFLEX BLUE RHODAMINE OR VIOLET INK SYMPTOM Job blocks at the bottom of the load due to adhesion from excess pressure W ork amp Turn blocks after second side because first side is sealed Job blocks during converting or in storage because ink coating is still too soft Inks contain dyes that can fade when exposed to ammonia or amines in coatings ANCHOR SOLUTION Reduce load height rack loads at 8 12 Increase time before second pass to allow ink coating to harden Reduce coating weight for second pass Reduce load temperature on second pass to prevent softening Use harder faster setting coating Allow to dry longer before handling Do not store work under hot humid conditions Allow work to dry completely before wrapping and shipping Ask your ink supplier for drawdowns to test the coating on before printing the job Use all pigment based equivalent inks that simulate PMS colors PROBLEM EXCESSIVE DRY BACK OR LOSS OF GLOSS FOAMING MOTTLE IN COATING MORE OBVIOUS IN SATIN AND MATTE JOBS SY
Download Pdf Manuals
Related Search