Home

Specifications: Troubleshooting: Dimensions:

1. 16842 Millikan Avenue Irvine CA 92606 Tel 800 662 0800 949 261 2999 Fax 949 261 7326 Website www seco larm com E mail sales seco larm com 931S22RRC_101204 pmd wif PITSW3 ENFORCER Sensor Retro Reflective Photoelectric Sensor Entry Alert System E 931CS22RRC Range 22ft 7m INSTALLATION MANUAL Features e Retro reflective photoelectric sensor e All components plug into each other e Range Up to 22 feet 7m No hard wiring required e Perfect for monitoring an entrance or for counting Optional counter available E 931ACC C foot traffic with optional counter Optional second speaker available E 931ACC S e Will make ding dong sound or siren sound when Includes the following the beam is interrupted Retro reflective photoelectric sensor e Speaker volume can be adjusted or turned off Reflector e When in siren mode sounding time is adjustable Speaker electronic chime from 3 to 30 seconds 9VDC adapter e 9VDC adapter included Caution e This sensor was not designed to prevent bodily injury or loss of life e Use of this sensor in certain security applications may be regulated by local laws or codes SECO LARM is not responsible for compliance with such laws or codes Included h m be Hanada Bak eg E 931ACC S Speaker Electronic Chime E 931ACC R E 931CS22RRC Transmitter Recei 1 Reflector ransmitter Receiver F 931ACC BLR1 Sample Installations S
2. Specifications ModelNumber EB3ICS22RRC O Sensing Range 22 7 m Light Source IR LED 49F 20 C _122 F 50 C Troubleshooting Possible Origin s Remedy s Sensor does not detect the object Sensor not aligned properly Change the angle of the sensor or reflector Red LED does not turn on 1 Reflector and or sensor is misaligned 1 Adjust the reflector and or sensor for 2 No power proper alignment 2 Check power adapter and cable Dimensions Lg 21s 60mm aa 2 50mm he 8mm ees a N 2 60n 2 2 GOmn 2 50n NOTICE The information and specifications printed in this manual are current at the time of publication However the SECO LARM policy is one of continual development and improvement For this reason SECO LARM reserves the right to change specifications without notice SECO LARM is also not responsible for misprints or typographical errors Copyright 2004 SECO LARM U S A Inc All rights reserved This material may not be reproduced or copied in whole or in part without the written permission of SECO LARM WARRANTY ENFORCER Photobeam Sensors are warranted against defects in material and workmanship while used in normal service for a period of one 1 year from the date of sale to the original customer Our obligation is limited to the repair or replacement of any defective part if the unit is returned transportation pre paid to SECO LARM SECO LARM U S A Inc
3. aker mode 1 Choose between Chime or Alarm sound or OFF 2 If Alarm was chosen A Set speaker to Alarm B Adjust the alarm sounding time from 3 to 30 seconds C Set speaker Volume Mounting the Speaker Electronic Chime Sample Sample Fixed Bracket Mounting Mounting Adjusting the Speaker Electronic Chime Wall mount hole Bracket E mounting holes Switch Chime switcht amp amp OFF Alarm o 3 Timer 3 30 Sec s S Volume 0 max 3 If Chime was chosen Set speaker to Chime 4 If OFF was chosen A Set speaker to OFF B The speaker will not sound when the beam is broken Using the Optional Counter 1 Automatically increases by 1 when sensor is triggered 2 Manually add 1 by pressing 3 Manually subtract 1 by pressing 4 Reset counter by pressing RESET Testing 1 Power up the sensor and speaker The red LED should be ON 2 Pass object to be detected between the sensor and reflector The red LED should turn OFF and the speaker if connected should sound Red LED 7 ENFORCER
4. tore front door Main entrance door A Other possible applications Offices stores schools warehouse vehicle detection etc Wiring one speaker no counter Sensor Adaptor Speaker Up to 22 7m Reflector Wiring one speaker with optional counter Sensor Adaptor Speaker Counter optional Up to 22 7m i Reflector Wiring with optional counter and second speaker Sensor Adaptor Speaker Speaker optional Counter optional Up to 22 7m Reflector Mounting the Reflector Sample Fixed Mounting Installation and Adjustment LED Functions RED LED When ON it indicates the sensor is powered and aligned properly Installation 1 Mount the reflector and sensor so they face each other at about 2 off the ground or knee high 2 Connect the sensor to the speaker 3 Connect power adaptor to the speaker e For signalling in multiple rooms add an optional second speaker E 931ACC S e Connect an optional counter E 931ACC C to the speaker output if desired 4 To find the correct alignment slowly adjust the angles of the sensor and or reflector up and down and right and left NOTE Correct alignment is reached when red LED turns ON Set Speaker Mode After the sensor and reflector have been properly installed the next step is to set the spe

Specifications: Troubleshooting: Dimensions:

Contents

Download Pdf Manuals

Related Search

Related Contents