Installation Manual - Niagara Pool & Spa
Contents
1. 21 293 23 403 BEADED VINYL LINER BEAD RECEIVER STEP 11 FILLING YOUR POOL Whether you are filling the pool with your own home water source or through a water fill service please use the chart at right to determine the water volume requirements for your particular size pool Please see your pool professional for instructions on proper water testing and balancing 48 Pool Wall 40 of water Pool Size 52 Pool Wall 44 of water Water Gallonage per Pool Size STEP 10 INSTALLING LINER TIP To help in removing stubborn wrinkles a shop vacuum may be used to suck the air out from behind the liner Attach shop vac to skimmer outlet and seal with duct tape Seal all other openings with duct tape as well Turn on vac and run till wrinkles are removed Once the wrinkles are gone begin filling with water After 6 of water is in the pool turn off and remove the shop vac BEADED VINYL LINER BEAD RECEIVER Clear all sticks and sharp objects from an area near the pool that is as large as the pool itself Remove the liner from its carton and unfold and open the liner Refold the liner so that it can easily be carried to the pool and unfold from the outside of the pool Check to make sure the sand in the pool is level and that there are no sharp objects in the pool Place the liner into the pool while holding onto the top of the wall section of the liner Snap the bead of the liner into the bead receiver ar2. For Site Preparation insstructions for Inground installation see page 12 STEP 2 PREPARING THE POOL SITE STEP 3 PATIO BLOCK INSTALLATION D Patio Block B C Patio Block Pool Radius A Pool Radius 12 5 Compression Seam Anchor Plate Patio Block Compression Seam Spline E Locate the wall section that is cut for the installation of both the skimmer and return fitting The location for this panel should be adjacent to the electrical supply and provide ease of access once the pool is installed Place the 2 wall sections so that the panels meet on center of a patio block At the end of each wall panel is a compression seam for the spline assembly Place an anchor plate on patio block centered under compression seams of meeting panels Attach wall sections using the provided splines Please be aware that each compression seam should be flush before attempting to insert the splines fig G Splines are designed to slide freely into place when inserted properly into leveled panels NOTE When inserting each spline please be aware that the outside spline should be inserted completely before inserting the inside spline Duplicate this process with the remaining wall panels stopping before installing the final wall panel At this time you need to bring in the sand through this opening to prepare the bottom of the pool 12 max STEP 4 WALL INSTALLATION Dished bottom option
3. Wall Clip Tek screw Pool Interior INGROUND CP2 COPING INSTALL Place pre bent coping length on top of the pool wall Se cure it with Tek screws at the previously installed 2 wall clips The next length is placed adjacent to the end of the first length continuing around the pool It is not necessary to leave spacing as with the standard white coping If you are installing a walk in step start at the step and continue around the pool cutting the last length to fit Install coping clips to cover the ends of the lengths 15 CONCRETE COLLAR GUIDE 16 2 8 Undistrubed Earth Drift Pin Drift Pin Undistrubed Earth 8 12 Drift Pin Concrete Collar at Step and A Frame Location Concrete Collar fig 1 fig 2 Estimating Concrete Requirements These are minimum estimating figures It is recommended that estimates be on the high end as the excess can be poured around A Frame and step Combine both figures below for total yards of concrete required Collar Pool Perimeter ft x 02 Yards required Pool Interior Pool Interior Check with local building codes before installing your Radiant Metric pool inground If the pool is to be installed in geographic areas with winter ground freezing Radiant Pools recommends a 6 to 8 concrete collar around the entire pool fig 1 If you are installing a walk in step Radiant Pools REQUIRES that a concrete collar be poured around the entire pool f
4. and reviewed the Pool Owner s Operating and Safety Information package which includes Safety Guide Consumer Care Manual Liner Warranty No Diving stickers instructions No Diving Sign Pool Owner Warning ________________________________________________________________________________________ Owner s Signature Date RADIANT POOLS METRIC SERIES RESIDENTIAL SWIMMING POOL NON PRORATED LIFETIME LIMITED WARRANTY There are no warranties that extend beyond the description on the face hereof This Warranty offered by Trojan Leisure Products LLC dba Radiant Pools of Albany NY herein called the Manufacturer is effective upon completion of payment by purchaser Manufacturer warrants its manufactured swimming pool components against manufacturing defects These components include wall panels panel connectors top and bottom channels all aluminum bracing components splines and aluminum nuts and bolts only This Warranty does not extend to equipment and other accessories not manufactured by Trojan Leisure Products LLC Manufacturer s Warranty performance is subject to the following terms and conditions Transportation Purchaser is responsible for all transportation charges incurred for any item returned for repair or replacement Costs Purchaser is responsible for the cost of installation or reinstallation of any item repaired or replaced under this Warranty Notification and Delivery Purchaser must notify Manufacturer of
5. any defect and the defective item must be delivered to Manufacturer transportation costs prepaid to 440 North Pearl Street Albany NY 12207 Manufacturer will effect repair or replacement within thirty 30 days of receipt unless purchaser is otherwise notified Warning For maximum use and enjoyment your Radiant Pool must be kept filled with water at all times Manufacturer shall not be responsible for any irregularities or imperfections that may result when water is removed from your Radiant Pools vinyl liner swimming pool Winter Damage Provision for Metric Series Pools Only The Manufacturer will replace or repair any of its manufactured swimming pool components as set forth above damaged due to the ill effects of ice or snow directly on pool only Any damage resulting from impact of any objects such as tree limbs or vehicles are excluded Purchaser must notify Manufacturer of any winter damage to receive a winter damage claim form Manufacturer will effect repair or replacement within thirty 30 days of receipt and final processing of winter damage claim form unless purchaser is otherwise notified Registration of Warranty After reading your Warranty please complete and return the enclosed registration card within sixty 60 days after delivery of your Radiant Pool or within thirty 30 days after installation of your Radiant Pool if installation is completed within a period less than sixty 60 days after delivery UNLESS OUR R
6. EGISTRATION CARD IS RETURNED AS DIRECTED THIS WARRANTY IS NULL AND VOID Transfer of Warranty The provisions of this Warranty are personal to the original purchaser of the Radiant Pool This Warranty is 100 transferable from the original purchaser The new owner must obtain a warranty transfer card from the original purchaser to be submitted to Manufacturer within sixty 60 days of purchase to maintain warranty 440 North Pearl Street Albany NY 12207 div Trojan Leisure Products LLC
7. ITH SAND OR OTHER DEBRIS AS THIS WILL CAUSE DIFFICULTY IN INSTALLATION Component 18 21 24 27 30 33 Panels 8 10 10 10 12 14 Rebar 8 10 10 10 12 14 Anchor Plates 8 10 10 10 12 14 Coping 8 8 10 10 12 14 White Cap Screws 50 50 50 50 100 100 Coping Clips 8 10 10 10 12 14 Splines 16 20 20 20 24 28 Bolts 3 8 x2 1 4 16 20 20 20 24 28 Skimmer Kit 1 1 1 1 1 1 Return Fitting 1 1 1 1 1 1 Vinyl Liner 1 1 1 1 1 1 2 IMPORTANT BEFORE YOU BEGIN The selection and preparation of the pool site is your responsibility The manufacturer can only suggest the proper techniques indicate the important considerations and emphasize the precautions and cannot be held responsible for damages to your pool that may result from failure to carefully follow all pool specifications All Radiant Pool components are engineered to provide a precise fit It is very important to handle all components with care Prior to assembly all pool components should be free of sand mud dirt and debris of any kind Do not allow splines or compressions seams to come in contact with sand or other debris as this will casue difficulty with installation We recommend a small dust broom or damp cloth be available in the event that any dirt or debris finds its way to these parts 3 STEP 1 SELECTING POOL LOCATION The selection and preparation of the pool site is your re
8. Installation Manual Metric Series Residential Swimming Pool WARNING DO NOT DIVE OR JUMP IT IS NOT DESIGNED FOR DIVING OR JUMPING YOUR POOL IS APPROXIMATELY 4 DEEP IF YOU DIVE OR JUMP INTO YOUR POOL YOU RUN THE RISK OF PERMANENT INJURY OR DEATH Enclosed in the liner box is the safety envelope The safety stickers must be installed as per instructions Failure to properly install warning labels will void warranty Alert all visitors and family of the risks associated with jumping and or diving and point out all warning labels supplied Failure to mount these safety labels may subject you to substantial liability in case of injury Your pool is designed for years of pleasurable safe family fun But when used incorrectly a swimming pool can be dangerous To insure your pool is used safely you must observe the following safety precautions 1 Do not dive do not jump no rough play no running or pushing 2 Do not walk on the top rail It can be slippery and is not a walkway 3 Be sure to install all safety labels provided with your pool according to the safety instructions 4 Keep a 50 safety rope with a flotation buoy with an outside diameter of 15 accessible in a prominent area by your pool 5 Post near all entrances to the pool area a list of telephone numbers for the following a Local police b Local fire department c Local rescue unit d Local ambulance service e Local hospital f 911 emergency number if avail
9. Skimmer Return Fitting Wall Section G Pool Exterior Pool Exterior Bring the required amount of clean and washed masonry sand into the interior of pool area Refer to the chart below for the required amount Once the sand has been placed inside the pool install the remaining wall panel STEP 5 SAND REQUIREMENTS 1 yard masonry sand appx 1 5 tons 18 2 21 3 24 3 5 27 4 5 30 5 5 33 6 5 Sand Amt cubic yds Pool Size 6 Install rubber gasket on the mounting plate making sure the gasket straddles both sides of the mounting plate fig H Slide skimmer face through pre cut skimmer opening keeping skimmer body on outside of pool wall Attach gray plastic mounting plate tightly to skimmer face using panhead screws into each side center holes as shown circled fig I Fasten assembly by inserting 2 countersunk bolts through corner holes in mounting plate through pre cut holes in pool wall and through corner holes in plastic backup plates securing with T nuts Hand tighten only Finish securing backup plates with 4 sheet metal screws per diagram The skimmer faceplate is attached after the liner is installed For Skimmer Assembly instructions for Inground installation see page 15 The return fitting is comprised of 3 pieces inlet fitting SP 1091Z10 and back nut fig J In geographic areas of deep winter ground freezing an inlet plate 3185 is recommended Ins
10. a building level transit and a measuring stick to determine the required depth of excavation It is best to set up the transit in a location so that you can leave it in the same place for the entire pool excavation It is best to keep the top of the pool 2 6 above the ground at the highest point so that you are able to place your deck on undisturbed soil Since the excavation will be 2 wider Recommended for the first time installations even though a 1 excavation is acceptable all around than the actual pool dimension it is important that the excavator does not dig the 2 ledge around the hopper too deep A sturdier pool will result when the pool rests on undisturbed earth It is better to have to remove a inch or two by hand then to have to build up after the excavator had gone too deep Any voids beneath the wall panels cause by large rock removal etc must be filled and properly compacted INGROUND LEVELING THE EXCAVATION TRANSIT 2 6 ABOVE HIGHEST GROUND OUTLINE OF POOL MEASURING STICK FLOOR OF EXCAVATION SIDE VIEW OF EXCAVATION SITE CORRECT INCORRECT UNDISTURBED EARTH CUT AWAY FILL IN POOL WALL POOL WALL If steps are going to be installed excavate a 6 foot by 10 foot area where they are to be located on the pool Please see the dig specifications for locations of steps IMPORTANT NOTE if installing steps with your Metric Inground installation you must begin the process at the step site Wall p
11. able 6 Provide fencing or an enclosure which is independent of the house as a closure around the entire pool area The fencing must be made of durable material a minimum of 4 high from ground level and with closures with self latching locks to make the pool inaccessible to toddlers and uninvited guests Make sure the gate is always closed Be sure to follow local building code requirements for load capacity and fencing if using an aftermarket or homebuilt deck 7 Check with your local town or municipality in regard to obtaining a building permit and or an electrical permit The installer shall follow the regulations for set backs barriers devices and other conditions 8 All electrical outlet connections should be a minimum of 5 from the outside perimeter of the wall of the pool From 5 10 there should be either a fixed connection outlet box or twist lock connection with a GFCI Connect power cords to a 3 wire grounding type outlet only 9 Severe electrical shock could result if you install your pump or filter on a deck They could fall into the water causing severe shock or electrocution Do not install on a deck or other surface at above or slightly below the top ledge of the pool within 5 feet of pool water edge 10 Do not sit stand or climb on the pump and filter or any part of the pool structure Components such as the filtration system pumps and heater must be positioned so as to prevent their being used as a means of access
12. anels must first be mounted to the step and wall panel assembly continues from there PREPARING FOR WALK IN STEP 12 Step Extension Plate Female Stair Connector T Spline Radius Wall Panel with Compression Seam Male Stair Connector Stair Flange Hex Bolt Hex Nut INGROUND WALK IN STEP INSTALLATION Metric step installation components Pool wall height 52 Step height 48 4 step extension plate to close gap at bottom of step Radius step connector 2 parts both are 48 long male portion attaches to the pool wall with splines female portion is bolted to the step flange Standard spline for interior side of pool Extended T spline for exterior side to connect A frame Each pool will have 1 panel that is shorter in length except the 27 pool which will have 2 shorter panels 1 Position the step in the installation location Level step establish pool height pool height will be wall height plus coping on top 2 Align the female stair connector with the side flange of the step as pictured The C receiver toward and flush with front interior edge of the step The top of the connector at finished wall height 3 Clamp connector in place drill step flange at holes in connector with a 7 16 drill bit bolt connector to the step do not tighten until all panels are completely connected 4 Slide male step connector down female connector attached to step 5 Install standard spline on in
13. arranty To prevent stones or other foreign material from damaging the liner it is recommended to build a 2 to 3 base of clean washed masonry sand or other suitable base material inside the entire pool 5 If ants or termites are prevalent in your area have soil treated with insecticides and allow sufficient time for them to dissipate before continuing with pool installation 6 Do not set up your pool under trees or under overhead wires 7 Do not set up your pool near any existing structure such as your house garage etc as this condition may compel diving or jumping into your pool which could result in permanent injury or death You must check with your local municipality for all appropriate ordinances and regulations 8 Do not set up your pool on or near any septic system or underground utilities NO NO NO NO CORRECT 4 Once the ground is prepared begin installing 2 x8 x16 patio blocks fig C The patio blocks should be installed at the perimeter line of the pool 1 2 the pool size from the center stake and at intervals corresponding to the number of panels associated with the size of the pool Please see chart for appropriate spacing Sink each patio block into the prepared ground making sure that each block is level in all directions side to side as well as front to back Repeat this step around the perimeter of the pool area making the tops of all blocks level with the ground Do not install
14. by the weight of the water on the beaded vinyl liner For the 18 pool the screw spacing should be approximately 24 beginning with the first screw approximately 2 3 over from a compression seam For all other pool sizes the screw spacing should be approximately 29 beginning with the first screw approximately 2 3 over from a panel joint The beaded vinyl liner with the weight of the pool water will draw coping into place and level on the interior of the pool wall Install coping clips by snapping over gaps between coping lengths For CP2 coping installation instructions for Inground installation see page 15 STEP 9 INSTALLING PLASTIC COPING STEP 8 PREPARING POOL COVE Pool Cove Interior Pool Wall K Using the masonry sand build a pool cove 6 to 8 high inside the wall along the entire circumference of the pool fig K This will prevent the liner from creeping under the wall This step is not optional and must be done Spread the remaining sand equally across the bottom of the pool This will give you a 2 to 3 sand base After the cove and base are in place dampen rake and tamp the entire pool area Make sure that no sand is allowed to remain on the wall above the cove This could cause pinholes in your liner Pool Exterior Wall Joint Pool Base Coping Clip L 8 18 6335 6963 21 8622 9477 24 11 262 12 378 27 14 254 15 666 30 17 645 19 388 33
15. f CP2 or Extrusion Coping Slide clips evenly spaced over radius wall panels to attach concrete receptor coping Clips are to be secured in place with tek screws through exterior pool wall Wall Clip Detail Pool Exterior Tek Screw 2 Wall Clip Pool Exterior 14 INGROUND SKIMMER ASSEMBLY Countersunk Bolts 4 Nuts 4 Skimmer Mounting Brackets 2 Skimmer 2 Male Adapter Skimmer Support Plastic Skimmer Mounting Plate 1 with gasket 1 Install rubber gasket on the mounting plate making sure the gasket straddles both sides of the mounting plate fig H Slide skimmer face through pre cut skimmer opening keeping skimmer body on outside of pool wall Fasten assembly by inserting 2 countersunk bolts through corner holes in mounting plate through pre cut holes in pool wall and through skimmer mounting brackets securing with hex nuts Tighten nuts to a snug fit Do not over tighten as this will damage the mounting plate Install skimmer support It is recommended that 2 PVC pipe be cut to size depending on installation Utilizing a 2 male adapter attach support to bottom of skimmer as shown Extension Collars fig I are used to raise the top of the skimmer to the height of decking The number of extension collars needed is determined by the variable decking height The skimmer faceplate is attached after the liner is installed Mounting Plate Gasket Tek screw 2
16. ig 2 Add 2 5 yards of concrete to the estimating concrete requirements for the concrete around the step and A frames Step Concrete A Frame Trojan Leisure Products LLC 440 North Pearl Street Albany NY 12207 518 434 4161 fax 518 432 6554 ANY IMPLIED WARRANTIES INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY LIMITED TO THE DURATION AND SCOPE OF THIS WRITTEN WARRANTY SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU UNDER NO CIRCUMSTANCES SHALL TROJAN LEISURE PRODUCTS LLC BE LIABLE FOR SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO ANY DAMAGES FOR LOSS OF USE OF POOL INJURY TO OR DEATH OF ANY PERSON OR DAMAGE TO PROPERTY AND ANY CLAIMS THEREFORE ARE HEREBY SPECIFICALLY DISCLAIMED AND EXCLUDED SOME STATES DO NOT ALLOW THE EXCLUSION OF SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES THEREFORE THE ABOVE LIMITATION MAY NOT APPLY TO YOU Owner Name ____________________________Serial No ________________________________________ Address ____________________________ City State Zip ________________________________________ Pool Size _________________________ Purchased From ________________________________________ Installed By Dealer Private Installer Owner Date of Installation ____________________________ IMPORTANT PLEASE READ AND SIGN I have received
17. l void all warranties Read all instructions for related accessories such as pumps filters etc prior to starting Before you start check your packing list to confirm that you have the correct number of parts and components The manufacturer reserves the right to revise change or modify construction of its pools See proceeding page for Metric Series Pool Components chart If there are any missing or damaged components please contact your retailer for replacement Even though all Radiant pools are designed to meet or exceed industry recommended safety standards special attention must be paid to all installation procedures that the installer performs and controls Spend time to assure that the entire pool framework is perfectly level Unlevel pools place extreme pressures on the pool walls An earth mound or pool cove must also be installed This keeps the pool liner from creeping out from under the pool wall Be sure to follow these instructions Improperly installed pools can rupture allowing thousands of gallons of water to rush out causing extensive property damage and injury to anyone in its path As with any major home project a homeowner is responsible for following all local laws ordinances and codes Electrical grounding of swimming pool is required National and local codes must be followed A checklist is provided below as a guide for these considerations simply brilliant With proper installation and care and maintenance this Me
18. ound the entire pool Gently pull on the liner and use a soft bristle broom to remove as many wrinkles as possible on the bottom of the pool Start filling the pool slowly with water Continue pulling gently and working the liner with a broom as needed Some wrinkling of the liner may be evident and in no way affects the structural strength of your pool You can continue to work out the wrinkles as needed by pulling gently on the liner or by using a broom 9 STEP 12 INSTALLING FACEPLATES Once the water level reaches 2 3 from the return and skimmer install the faceplates Carefully locate the screw holes in for each opening Once located carefully puncture the liner with an icepick or nail Attach faceplate with 1 screws and hand tighten evenly till snug Using a razor knife carefully trim the liner out of the openings for the skimmer and return When done install the eyeball into the return Locate screw holes Trim liner from skimmer opening Trim liner from return opening Skimmer faceplate installed Return faceplate installed Please refer to pump and filter manufacturers installation instructions STEP 13 CONNECTING PLUMBING 10 Metric Inground Installation Instructions 11 With the shape of the pool excavation marked out its height relative to the ground must be determined The pool should be set at a height so that rain and splash will drain away rather than towards the pool It is best to use
19. sponsibility The manufacturer can only suggest the proper techniques indicate the important considerations and emphasize the precautions and cannot be held responsible for damages to your pool that may result from failure to carefully follow all pool specifications 1 The surface on which your pool will stand must be absolutely level and solid This condition should extend 1foot beyond the actual pool area all around The best surface is bare solid earth free from stones roots and other sharp objects Fill 2 Allow plenty of play area around the pool Fit the location into your landscaping plans 3 The pool site must be accessible to electrical and water supply and should allow for disposal of great quantities of water when the pool is drained All electric outlets within 10 must be GFI protected 5 Do not set up your pool in hilly areas or areas with poor drainage For Semi Inground and Inground Installations The site of installation must accomodate an efficient drainage system to minimize the impact of heavy rain and high ground water conditions 4 When installing your pool on a solid level surface it is imperative that you protect your pool and liner from chemicals and other foreign matter contained in the surface Do not install your pool on peat moss tar paper roots sticks gravel or chemically treated or contaminated soil not approved for pool use Any or all of these surfaces can ruin your pool and liner and will void your w
20. tall the return fitting by threading the SP 1091Z10 into the inlet fitting Place the assembly into the pre cut hole slide the inlet plate over the exposed threads and then thread the back nut onto the SP 1091Z10 fitting All threaded connections should be prepared using a combination of Teflon tape and marine grade silicone The return faceplate is attached after the liner is installed STEP 6 SKIMMER ASSEMBLY I Gray Plastic Skimmer Mounting Plate w gasket 1 2 countersunk bolts 4 Sheet metal screws 4 Skimmer Pre cut Skimmer Mounting holes 4 Plastic Backup Plates 2 SP 1091Z10 Back Nut Inlet Fitting STEP 7 RETURN FITTING ASSSEMBLY J Inlet Plate H Mounting Plate Gasket 7 2 EPS FOAM INSULATION ACRYLIC COATED ALUMINUM WALL BEADED VINYL LINER DURABLE PVC COPING PVC COPING CLIP The plastic coping is attached by simply snapping over the pool wall Each coping joint should be offset from a wall joint fig L You need to leave a 1 gap between lengths of coping Once all of the coping has been placed secure the coping to the pool wall with the white cap screws provided Using a 3 32 drill bit drill through the plastic coping and EXTERIOR pool wall while pressing down firmly on the coping on top of pool wall Using a Phillips screw driver hand tighten each screw DO NOT OVERTIGHTEN Note Plastic coping on the interior side of the pool wall will be held in place
21. terior side of pool and extended T spline on exterior side connecting the step to the first panel 6 Install A frames at the 2 extended splines check level of step tighten the step connector bolts 7 Check panel joints for proper location using the radius of pool from the established center point of the pool 8 Encase the base of the pool and step with a concrete collar See concrete requirements on next page 9 Follow step Manufacturer s instructions for installation of step gasket and faceplate after the liner is installed 18 8 Radius 21 8 Straight 24 8 Straight 27 8 Straight 30 8 Straight 33 8 Straight Step Type 48 Height Pool Size Step Specifications for Metric Pools Note Drawings are for illustrative purposes and are not to scale Attachment detail will vary for steps from different manufacturers 13 2 Wall Clips Hex Bolts Wall Anchor Pool Interior Anchor Plates Wall anchors are located at each compression seam With a high speed metal drill bit drill two 7 16 holes on each side of the compression seam in each wall anchor as shown Insert a provided nut and bolt through each drilled hole as illustrated with the nut on the outside of the pool fig 1 Drive rebar through one bottom hole to secure in proper Duplicate this process with the remaining anchor plates INGROUND ANCHORS PLATES AND WALL CLIPS Wall Clips for Installation o
22. the blocks on loose sifted soil or sand All patio blocks must be flush with the ground solid and level with each other in all directions Once all of the patio blocks are installed place a joiner plate on each patio block fig E The joiner plates will be used to provide a level platform for wall installation 18 6 10 5 8 8 21 6 5 7 8 10 24 7 5 10 27 8 4 1 8 10 30 7 9 1 8 12 33 7 4 1 8 14 Patio Block Intervals Pool Size Qty Needed Once you have chosen an appropriate location for your pool based on the criteria specified above determine the pool circumference by putting a stake in the ground at the center of the location desired and with a line equal in length to the radius of the pool 1 2 the pool size plus 12 mark off the circumference with a sharp object lawn edger spray paint etc fig A After all of the sod has been removed you must make the pool area absolutely level as measured by a transit or level Find the lowest spot within the pool area and level the ground to that lowest spot fig B Do not add dirt to the low areas It is the high areas that must be dug away The perimeter of the pool must be a solid foundation to prevent the pool from settling into dirt that is loosened by rain and water splashing over the side Once again clean the area of all sharp objects including roots and rocks that could later effect your swimming pool
23. to the pool by young children 11 Never drink alcoholic beverages or use any intoxicants which could hinder your judgment and reflexes 12 Never use the pool alone All children must be supervised continuously 13 Do not use pool if bottom is not clearly visible At night sufficient lighting must be available It is the pool owners sole responsibility to provide adequate lighting for the pool bottom safety signs and walkways which exceeds minimum standards of the IES of North America 14 Be sure that all toys chairs and tables or similar objects that a young child could climb on be at least 4 from the pool 15 Do not use pool during electrical or rain storms 16 See available Association of Spa and Pool Professionals APSP publications for more tips on pool safety IMPORTANT SAFETY INFORMATION INTRODUCTION Installation of the Metric Series above ground pool is not extremely hard or confusing The installation of an average size aboveground pool 18 33 diameter will usually require 2 3 people to help set it up The secret to installing a pool so that it will give you years of enjoyment is to take the time to follow the step by step instructions It is very important to follow the instructions in the sequence laid out in this manual Included in this manual is an assortment of tools and materials which you will need for preparing the ground checking the levelness and setting up the pool Failure to follow instructions exactly wil
24. tric Series Residential Swimming Pool from Radiant Pools will provide a lifetime of fun and relaxation for you and your family and friends Radiant Pools offers a non prorated lifetime warranty on the entire pool against manufacturing defects Walls panels and aluminum components are warranteed against factory defects due to faulty workmanship or defects due to manufacturing for as long as you own your pool Compare our warranty with any other pool manufactured Engineering innovation and efficiency make the difference It s simply brilliant Obtain building permit if required Local building and zoning requirements Electrical and Grounding requirements Proper Backfill and Drainage Fencing requirements Backwash waste water requirements Check availability of utilities Call before you dig www digsafe com HOMEOWNER CHECKLIST 1 TOOLS NEEDED MATERIALS NEEDED Tape measure 50ft Hose with spray nozzle Level Step Ladder Long handled pointed shovel Short handle square shovel Pick or mattock Garden rake Stake Power Drill Tamper 10 or 12 in Square Hacksaw Razor knife Pool trowel Screwdrivers Flathead and Phillips String 2x4 Masonry Sand Spray Paint Soft bristle broom Patio Blocks 2 x8 x16 POOL COMPONENTS CHECKLIST included for inground installation only IMPORTANT NOTE DO NOT ALLOW SPLINES OR COMPRESSION SEAMS TO COME IN CONTACT W
Download Pdf Manuals
Related Search