ET850 USER'S MANUAL
Contents
1. IJ EB Ra Remarks After installing the heat spreader provided with the CPU module please install an additional heat spreader for better heat dissipation 4 ET850 User s Manual INTRODUCTION Installing the Memory The ET850 COM Express CPU module accommodates 240 pin DDR3 SODIMM memory modules with capacities up to 4GB Non ECC is supported Installing and Removing Memory Modules To install the DDR3 modules locate the memory slot on the board and perform the following steps m W Hold the DDR3 module so that the key of the DDR3 module align with those on the memory slot Insert the module into the socket at a slight angle approximately 30 degrees Note that the socket and module are both keyed which means that the module can be installed only in one direction To seat the memory module into the socket apply firm and even pressure to each end of the module until you feel it slip down into the socket With the module properly seated in the socket rotate the module downward Continue pressing downward until the clips at each end lock into position 4 To remove the DDR3 module press the clips with both hands ET850 User s Manual 5 INTRODUCTION Jumpers and Connectors on ET850 JB1 Clear CMOS Setting JB1 Setting UE oa Note With jumper pin 1 2 short it automatically saves the last BIOS settings whe2. 2 ET850 User s Manual INTRODUCTION B BaBABD O b bAG amp hkkbEEpAAAAESXE CAM AjyM W VA ZLLML NUR en ET850 Specifications Form Factor COM Express CPU module CPU Type AMD Geneva ASB2 Turion II Neo Athlon II Neo DC CPU CPU Dual Core CPU 27 x 27 mm 45nm SOI ECC capable Operate FSB up to 3200 MHz Hyper Transport Frequency AMD Athlon II Neo N36L 1 3GHz DC 12W ET850 13 AMD Turion Neo N54L 2 2GHz DC 25W ET850 22 AMD Turion Neo N54H 2 2GHz DC 25W ET850 22H Cache AMD SB820M SB 21mm x 21mm BIOS AMIBIOS Memory DDRIII 800 SO DIMM x1 Max 4GB Non ECC Please note N54H can support to 1333MHz AMD 785E built in ATi HD4200 Graphics Core CRT w DF13 connector via internal RAM DAC x2 via LVTM A Realtek 8111DL PCI Express GbE x 1 USB TC LVDS AMD 785E built in 1 x 24 bit dual channels w DF13 socket LAI SB820M built in USB 2 0 host controller supports 8 ports Gb s JMicron JM368 PCI e to PATA x1 for 1 PATA channel for IDE ue SB820M Built in Audio controller HD Codec ALC662 w 6 channels Line out Line in Mic Two 220 pin connectors A B amp C D to Carrier Board COM Express 2 0 standard Power 5V 33V 12V 5VSB Other LAN Wakeup RoHS 95mm x 128mm ET850 User s Manual 3 INTRODUCTION Dimensions
3. Advanced Settings Configure CPU WARNING Setting wrong values in below sections may cause system to malfunction gt CPU Configurations gt IDE Configuration gt Super IO Configuration gt ACPI Configuration gt AHCI Configuration gt Hardware Health Configuration PCI Express Configuration gt USB Configuration gt Lan Configuration gt Power Configuration lt Select Screen 14 Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit o The fields in each section are shown in the following sections as seen in the computer screen Please note that setting the wrong values may cause the system to malfunction If unsure please contact technical support of your supplier BIOS SETUP UTILITY p Advanced CPU Configuration Module Version 15 08 AGESA Version 1 0 0 0 Physical Count 1 Logical Count 2 This option should remain disabled for the normal operation The driver developer may enable it for testing purpose AMD Turion Neo N54L Dual Core Processor Revision C3 Cache L1 256KB Cache L2 2048KB Cache L3 N A Speed 2200MHz NB CIk 1600MHz Able to Change Freq Yes uCode Patch Level 0x10000B6 GART Error Reporting Microcode Update Secure Virtual Machine Mode PowerNow C1E Support Disabled Enabled Enabled Enabled Enable lt Select Screen 14 Select Item Change Field
4. ATI Catalyst Install Manager 2 Actions taken by Catalyst Install Manager require a system reboot MS Would you like to reboot now e a lM 34 ET850 User s Manual DRIVERS INSTALLATION Audio Drivers Installation 1 Insert the CD that comes with the board Click AMD then AMD 785E Chipset Drivers and then Realtek High Definition Audio Driver ligh Definition Audio D 2 The Welcome screen to the InstallShieled Wizard for Realtek High Definition Audio Driver will appear At this point click Next to continue the installation process 3 When installation is completed restart the computer as prompted Click Finish ER L MLIMA ET850 User s Manual 35 DRIVERS INSTALLATION LAN Drivers Installation 1 Insert the CD that comes with the board Click LAN Card at the left side and then Realtek LAN Controller Drivers Intel AMD LAN Card Tools Intel AMD LAN Card Tools Intel LAN Controller Drivers Marvell LAN Controller Driver Realtek LAN Controller Drivers Realtek RTL8103EL LAN Drivers Realtek RTL8111C LAN Drivers postek taa DE LAN Drivers Support Realtek RTLS111DL LAN Drivers 36 ET850 User s Manual DRIVERS INSTALLATION E 2 In the welcome screen of the InstallShield Wizard for REALTEK GbE amp FE Ethernet PCI E NIC Driver click Next REALTEK GbE amp FE Ethernet PCI E NIC Driver InstallShield Wizard welcome to the InstallShield Wizard for R
5. F1 General Help F10 Save and Exit ESC Exit 12 ET850 User s Manual BIOS SETUP eee BIOS SETUP UTILITY DISABLED disables the IDE Configuration integrated IDE Controller OnBoard PCI IDE Controller Both PRIMARY enables only the Primary IDE Controller Primary IDE Master Not Detected SECONDARY enables Primary IDE Slave Not Detected eee ae IDE Secondary IDE Master Not Detected anos Secondary IDE Slave Not Detected Co DES both IDE Third IDE Master Not Detected Third IDE Slave Not Detected Fourth IDE Master Not Detected Fourth IDE Slave Not Detected TL Select Item Change Field Hard Disk Write Protect Disabled F1 General Help IDE Detect Time Out Sec 35 F10 Save and Exit ATA PI 80Pin Cable Detection Host amp Device ESC Exit lt Select Screen The IDE Configuration menu is used to change and or set the configuration of the IDE devices installed in the system M t ET850 User s Manual 13 BIOS SETUP ee BIOS SETUP UTILITY Configure Win627EHF Super IO Chipset Allows BIOS to Select Serial Port Base Floppy A Disabled Addresses Serial Port1 Address 3F8 IRQ4 Serial Port2 Address 2F8 IRQ3 Serial Port2 Mode Normal lt Select Screen Parallel Port1 Address 378 TL Select Item Parallel Port Mode Normal Change Field M nos herons Loss E Off FT General Help p F10 Save and Exit Power On function None
6. A45 USBO B45 USB1 C45 PCI AD25 D45 PCI AD30 A46 USB0 B46 USB1 C46 PCI AD27 D46 PCI IRQC A47 VCC_RTC B47 EXCD1_PERTST C47 PCI_AD29 D47 PCI_IRQD A48 EXCDO_PERST B48 EXCD1_CPPE C48 PCI_AD31 D48 PCI CLKRUNZ A49 EXCDOCPPE B49 SYS RESET C49 PCI IRQA D49 NC A50 LPC SERIRQ B50 CB RESET C50 PCI IRQB3 D50 PCI CLK ET850 User s Manual INTRODUCTION Pin Signal Pin Signal Pin Signal Pin Signal A51 GND FIXED B51 GND FIXED C51 GND FIXED D51 GND FIXED A52 PCIE TX5 B52 PCIE RX5 C52 PEG RXO D52 PEG TX0 A53 PCIE TX5 B53 PCIE RX5 C53 PEG RXO D53 PEG TXO A54 GPIO B54 GPO1 C54 NC D54 PEG LANE RV A55 PCIE TX4 B55 PCIE RX4 C55 PEG RX1 D55 PEG TX1 A56 PCIE TX4 B56 PCIE RX4 C56 PEG RX1 D56 PEG TX1 A57 GND B57 GPO2 C57 NC D57 NC A58 PCIE_TX3 B58 PCIE_RX3 C58 PEG RX2 D58 PEG TX2 A59 PCIE TX3 B59 PCIE RX3 C59 PEG RX2 D59 PEG TX2 A60 GND FIXED B60 GND FIXED C60 GND FIXED D60 GND FIXED A61 PCIE TX2 B61 PCIE RX2 C61 PEG RX3 D61 PEG TX3 A62 PCIE TX2 B62 PCIE RX2 C62 PEG RX3 D62 PEG TX3 A63 GPI1 B63 GPO3 C63 RSVD D63 RSVD A64 PCIE TX1 B64 PCIE RX1 C64 RSVD D64 RSVD A65 PCIE TX1 B65 PCIE RX1 C65 PEG RX4 D65 PEG TX4 GND WAKEO PEG RX4 GPI2 WAKE1 RSVD PCIE T
7. POST messages When enabled this displays OEM Logo instead of POST messages AddOn ROM Display Mode This allows user to force BIOS Option ROM of add on cards to be displayed during quiet boot Bootup Num Lock This select the power on state for numlock PS 2 Mouse Support This select support for PS 2 mouse Wait for F1 If Error When set to Enabled the system waits for the F1 key to be pressed when error occurs This allows option ROM to trap interrupt 19 Hit DEL Message Display This displays Press DEL to run Setup in POST Interrupt 19 Capture This allows option ROMs to trap interrupt 19 Eann OUM UM ET850 User s Manual 21 BIOS SETUP HII OOO Q Security Settings This setting comes with two options set the system password Supervisor Password sets a password that will be used to protect the system and Setup utility User Password sets a password that will be used exclusively on the system To specify a password highlight the type you want and press Enter The Enter Password message prompts on the screen Type the password and press Enter The system confirms your password by asking you to type it again After setting a password the screen automatically returns to the main screen To disable a password just press the Enter key when you are prompted to enter the password A message will confirm the password to be disabled Once
8. RAS RAS Delay Trrd 4 CLK N A Row Cycle Trc 20 CLK N A ESC Exit Read to Precharge Trtp 4 CLK NA Write Recover Time Twr 6 CLK N A HT Link Width Control Enable GfxNBPstateDis Support Enable TOTime Override Disabled ET850 User s Manual 23 BIOS SETUP Memory Configuration BIOS SETUP UTILITY Chipset Memory Configuration Enable Channel Memory Channel Interleaving Auto Interleaving Enable Clock to All DIMMs Disabled Memory Hole Remapping Enabled CS Sparing Enable Disabled Power Down Enable Auto Power Down Mode Auto DRAM Parity Enable Auto e Bank Swizzle Mode Select Screen 1 Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit DRAM Timing Configuration BIOS SETUP UTILITY Chipset DRAM Timing Configuration DRAM Timing Config Auto Auto Manual lt Select Screen f Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit 24 ET850 User s Manual BIOS SETUP EEE NorthBridge2 Chipset Configuration BIOS SETUP UTILITY Chipset NorthBridge2 Chipset Configuration RS880 CIMx Version 1 3 0 5 gt Internal Graphics Configuration NB Power Management Features Auto Memory Hole Disabled lt Select Screen tl Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit Internal Graphics Configuration BIOS SETUP UTILITY Chipset Internal Gra
9. Software AMD Hardware You own the medium on which the Software is recorded but AMD and AMD s Licensors referred to collectively as AMD retain title to the Software and related documentation You may a use the Software solely in conjunction with the AMD Hardware on a single computer b make one copy of the Software in machine readable form For backup purposes only You must reproduce on such copy AMD s copyright notice and any other proprietary legends that were on the original copy of the Software c transfer all your license rights in the Software provided you must also transfer a copy of this License the backup copy of the Software the AMD Hardware and the related documentation and provided the other party reads and agrees to accept the terms and conditions of this License Upon such transfer your license is then terminated 2 Restrictions The Software contains copyrighted and patented material trade secrets and other proprietary material In order to protect them and except as permitted by applicable legislation you may not a decompile reverse engineer disassemble or otherwise reduce the Software to a human perceivable Form b modify network rent lend loan distribute or create derivative works based upon the Software in whole or in part or ET850 User s Manual 33 DRIVERS INSTALLATION ATI Catalyst Install Manager Version 03 00 0782 X Finished Installation complete Finished
10. drives serial ports and parallel ports It also adds virus and password protection as well as special support for detailed fine tuning of the chipset controlling the entire system BIOS Setup The BIOS provides a Setup utility program for specifying the system configurations and settings The BIOS ROM of the system stores the Setup utility When you turn on the computer the BIOS is immediately activated Pressing the Del key immediately allows you to enter the Setup utility If you are a little bit late pressing the Del key POST Power On Self Test will continue with its test routines thus preventing you from invoking the Setup If you still wish to enter Setup restart the system by pressing the Reset button or simultaneously pressing the Ctrl Alt and Delete keys You can also restart by turning the system Off and back On again The following message will appear on the screen Press lt DEL gt to Enter Setup In general you press the arrow keys to highlight items Enter to select the lt PgUp gt and lt PgDn gt keys to change entries F1 for help and Esc to quit When you enter the Setup utility the Main Menu screen will appear on the screen The Main Menu allows you to select from various setup functions and exit choices 70 ET850 User s Manual BI
11. the password is disabled the system will boot and you can enter Setup freely BIOS SETUP UTILITY Advanced PCIPnP Boot Security Chipset Install or Change the Password Security Settings Supervisor Password Not Installed User Password Not Installed Change Supervisor Password lt Select Screen Change User Password 14 Select Item Enter Change Boot Sector Virus Protection Disabled F1 General Help F10 Save and Exit ESC Exit EE T E Se 22 ET850 User s Manual BIOS SETUP Advanced Chipset Settings This setting configures the north bridge south bridge and the ME subsystem WARNING Setting the wrong values may cause the system to malfunction BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit Advanced Chipset Settings Options TOF NB North Bridge Configuration gt North Bridge2 Configuration fl South Bridge Configuration lt Select Screen Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit BIOS SETUP UTILITY Chipset North Bridge Chipset Configuration Memory Configuration DRAM Timing Configuration Size of Dimm 0 1 GB Size of Dimm 1 Non Presence lt Select Screen Memory CLK 400 MHz N A tl Select Item CAS Latency Tcl 6 CLK N A Enter Go to Sub Screen RAS CAS dELAY Trcd 6 CLK N A F1 G Hel Row Precahrge Time Trp 6 CLK N A enera Help Min Active RAS Tras 15 CLK N A F10 Save and Exit
12. 14 D99 PEG TX14 A100 GND FIXED B100 GND FIXED C100 GND FIXED D100 GND FIXED A101 RSVD B101 RSVD C101 PEG RX15 D101 PEG TX15 A102 RSVD B102 RSVD C102 PEG RX15 D102 PEG TX15 A103 RSVD B103 RSVD C103 GND D103 GND A104 VCC 12V B104 VCC 12V C104 VCC 12V D104 VCC 12V A105 VCC 12V B105 VCC 12V C105 VCC 12V D105 VCC 12V A106 VCC 12V B106 VCC 12V C106 VCC 12V D106 VCC 12V A107 VCC 12V B107 VCC 12V C107 VCC 12V D107 VCC 12V A108 VCC 12V B108 VCC 12V C108 VCC 12V D108 VCC 12V A109 VCC 12V B109 VCC 12V C109 VCC 12V D109 VCC 12V A110 GND FIXED B110 GND FIXED C110 GND FIXED D110 GND FIXED ET850 User s Manual BIOS SETUP BIOS Setup This chapter describes the different settings available in the AMI American Megatrends Inc BIOS that comes with the board The topics covered in this chapter are as follows BIOS Introduction BIOS Setup Main BIOS Setup Advanced Settings iau iais si into di tete os aaa Dai 12 PCIPnP Settings Boot Settings Security Settings Advanced Chipset Settings sse 23 Exit Set p eR Ais a aae Uam a ten Save Changes and Exit Discard Changes and Exit Discard Changes Load Optimal Defaults Load Failsafe D fauts ee pee tees ET850 User s Manual 9 BIOS SETUP RST RE BIOS Introduction The BIOS provides critical low level support for a standard device such as disk
13. Completed MARVELL The InstallShield Wizard has successfully installed Marvell Miniport Driver Click Finish to exit the wizard Finish 7 To use the wake up function with PCIe LAN go to the Device Manager under Windows and select LAN controller The window for Generic Marvell Yukon Chipset based Ethernet Controller Properties will appear Click Advanced and select Wake From Shutdown In the Value field on the right select On 8 Then also in the Advanced section click on Wake Up Capabilities In the Value field on the right select Magic Packet then click OK ET850 User s Manual 39 DRIVERS INSTALLATION Y This page is intentionally left blank 40 ET850 User s Manual
14. Drivers Installation 1 Insert the CD that comes with the board Click AMD then AMD 785E Chipset Drivers and then AMD 785E Series Graphics Drivers Intel AMD 785E Chipset Drivers AS LAN Card Tools AMD 785E Series Graphics Drivers d AMD Realtek High Derikition Audio Driver S zr LAN Card v Tools ATI AMD 785E Series Graphics Drivers 30 ET850 User s Manual DRIVERS INSTALLATION 2 When the Welcome Screen appears click Next Click Install to install the ATI software components ATI Catalyst Install Manager Version 03 00 0782 Welcome Welcome Welcome Catalyst Install Manager is used to install and update the software For your graphics products r Language Support Which language would you like Catalyst Install Manager to display es http ati amd com Cancel ATI Catalyst Install Manager Version 03 00 0782 Select Installation Operation Install Allow users to install ATI software components Uninstall Remove ATI software components http ati amd com Cancel ET850 User s Manual 37 DRIVERS INSTALLATION 3 Click Custom and select the components to install as shown ATI Catalyst Install Manager Version 03 00 0782 Installer Welcome Welcome Welcome Select Express or Custom Install and then click Next Default Installation Location C Program Files ATI Technologies http ati amd com ATI Catalys
15. EALTEK GbE amp FE Ethernet PCI E NIC nyer The InstallShield Wizard will install REALTEK GbE amp FE Ethernet PCI E NIC Driver on your computer To continue click Next 3 In the InstallShield Wizard screen click Install to begin the installation 4 InstallShield Wizard completed Click Finish to exit the Wizard e C L ET850 User s Manual 37 DRIVERS INSTALLATION Marvell LAN Drivers Installation IP401 B1 carrier board only Follow the steps below to complete the installation of the Intel PRO LAN drivers 1 Insert the CD that comes with the board Click LAN Card and then Marvell LAN Controller Driver ell LAN Controller Driver 2 When the Welcome screeen appears click Next to continue mm Marvell Miniport Driver InstallShield Wizard x Welcome to the InstallShield Wizard for MARVELL Marvell Miniport Driver The InstallShield R Wizard will install Marvell Miniport Driver on your computer To continue click Next WARNING This program is protected by copyright law and international treaties Cancel 38 ET850 User s Manual DRIVERS INSTALLATION 3 Click Next to agree with the license agreement 4 When the Readme Information appears click Next to continue 5 When the Ready to Install the Program appears click Install to continue 6 After the installation is complete click Finish ie Marvell Miniport Driver InstallShield Wizard InstallShield Wizard
16. ESC Exit Onboard Serial Port The default values are Serial Port 1 3F8 IRO4 Serial Port 2 2F8 IRQ3 Restore on AC Power Loss This field sets the system power status whether Power On or Power Off when power returns to the system from a power failure situation Configure Secondary Fintek F81216D Super IO Allows BIOS to Select Chipset Serial Port Base Serial Port3 Address 3E8 Addresses Serial Port3 Mode 5 Serial Port4 Address 2E8 lt Select Screen 1 Select Item Change Field F1 General Help F10 Save and Exit ESC Exit Serial Port4 Mode 10 Ge T I E T SS Si 14 ET850 User s Manual BIOS SETUP BIOS SETUP UTILITY General ACPI Configuration settings ACPI Settings gt General ACPI Configuration Advanced ACPI Configuration BIOS SETUP UTILITY Select the ACPI state used for Suspend mode S1 POS System Suspend C1E Support Enable General ACPI Configuration BIOS SETUP UTILITY Advanced ACPI Configuration Enable RSDP pointers to 64 bit Fixed System ACPI Version Features ACPI v1 0 Description Tables ACPI APIC support Enabled Different ACPI version AMI OEMB table Enabled Headless mode Disabled Has some addition BIOS SETUP UTILITY Enables for supporting AHCI controller in AHCI AHCI BIOS Support mode during BIOS control otherwise operates in IDE mode AHCI Settings Enabled AHCI PortO Not Detected AHCI Port1 Not Detected A
17. ET850 AMD Athlon I Turion II Neo CPU 785E SB820M COM Express Type II CPU Module USER S MANUAL Version 1 0A Acknowledgments PS 2 is a trademark of International Business Machines Corporation AMD and Athlon Neo are registered trademarks of Advanced Micro Devices Inc Microsoft Windows is a registered trademark of Microsoft Corporation All other product names or trademarks are properties of their respective owners ii ET850 User s Manual Table of Contents Table of GCont nts i geo a ais iii Introduction oe oo epe 1 Product DescriptiOn aeneis etae i ERES 1 Checklist ose e RE en en s 2 ET850 Specifications 3 Dimensions his Eee DE deer niece tede 4 Installing the Memory nennen nen 5 Jumpers and Connectors on ET850 sese 6 JB1 Clear CMOS Settings 6 J2 J3 COM Express Type 2 Connectors esee 6 COM Express Type 2 Connectors eese 7 BIOS Setup amo a a 9 Drivers Installation 29 VGA Drivers Installation esses 30 Audio Drivers Installation un 35 LAN Drivers Installation 36 Marvell LAN Drivers Installation IP401 B1 carrier board only 38 HH ET850 User s Manual iii The ET850 COM Express CPU Module iv ET850 User s Manual INTRODUCTION Introduction Product Description T
18. Exit The USB Configuration menu is used to read USB configuration information and configure the USB settings Legacy USB Support Enables support for legacy USB AUTO option disables legacy support if no USB devices are connected USB 2 0 Controller Mode Configures the USB 2 0 controller in HiSpeed 480Mbps or FullSpeed 12Mbps This option is enabled by HiSpeed ET850 User s Manual 77 BIOS SETUP TEZ BIOS EHCI Hand Off Enabled Disabled This is a workaround for Oses without EHCI hand off support The EHCI ownership change should be claimed by EHCI driver Legacy USB1 1 HC Support Support USB1 1 HC BIOS SETUP UTILITY I Advanced I Lan Configuration Options Onboard LAN Option ROM Disabled Disabled Enabled Co BIOS SETUP UTILITY Power Configuration Disable Enable g RTC to generate a wake event RTC Resume Disabled Resume By Ring Disabled Resume By PCI Card Disabled poao a U I EET 18 ET850 User s Manual BIOS SETUP E OOU ETI PCIPnP Settings This option configures the PCI PnP settings BIOS SETUP UTILITY Advanced PCIPnP Boot Security Chipset t NO lets the BIOS Advanced PCI PnP Settings Configure all the WARNING Setting wrong values in below sections Devices in the system may cause system to malfunction YES lets the Clear NVRAM No operating system Plug amp Play O S No configure Plug and PCI La
19. HCI Port2 Not Detected AHCI Port3 Not Detected AHCI Port4 Not Detected AHCI Port5 Not Detected ET850 User s Manual 15 BIOS SETUP BIOS SETUP UTILITY Options Hardware Health Configuration System Temperature 75 C 167 F Disabled CPU Temperature 78 C 172 F 80 C 176 F 85 C 185 F CPU_VDD_RUN 1 148V 90 C 194 F CPU_VDDR 0 902V 95 C 203 F 3 3V 3 260V 5V 4 933 V vcc 4 914 V 5VSB 4 872 V lt Select Screen CPU Shutdown Temperature Disabled 14 Select Item Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit BIOS SETUP UTILITY Enables Disables Pci Express Device Relaxed Ordering Auto Relaxed Ordering Maximum Payload Size Auto PCI Express Configuration Extended Tag Field Auto No Snoop Auto Maximum Read Reqquest Size Auto Active State Power Management Disabled Extended Synch Auto 16 ET850 User s Manual BIOS SETUP BIOS SETUP UTILITY Configure the USB Mass Storage Class Devices USB Configuration Module Version 2 24 5 13 4 USB Devices Enabled 1 Keyboard 1 Mouse 1 Drive Legacy USB Support Enabled lt Select Screen USB 2 0 Controller Mode HiSpeed tl Select Item BIOS EHCI Hand Off Enabled Change Field Legacy USB1 1 HC Support Enabled F1 General Help F10 Save and Exit gt USB Mass Storage Device Configuration ESC
20. IDE CS14 SATAO TX SATA1 TX PCI REQ2 IDE_CS3 A18 NC B18 SUS STAT C18 PCI_GNT1 D18 IDE_RESET A19 SATAO RX B19 SATA1 RX C19 Pcl REQ1 D19 PCI GNT3 amp A20 SATAO RX B20 SATA1 RX C20 PCI GNTO D20 PCI REQ3 A21 GND FIXED B21 GND FIXED C21 GND FIXED D21 GND FIXED A22 NC B22 NC C22 PCI_REQO D22 PCI_AD1 A23 NC B23 NC C23 PCI_RESET D23 PCI_AD3 A24 SUS_S5 B24 PWR_OK C24 PCI ADO D24 PCI AD5 A25 NC B25 NC C25 PCI AD2 D25 PCI AD7 A26 NC B26 NC C26 PCI AD4 D26 PCI C BEOZ A27 BATLOW B27 WDT C27 PCI AD6 D27 PCI AD9 A28 SATA ACT B28 HDA SDIN2 C28 PCI AD8 D28 PCI AD11 A29 HDA SYNC B29 HDA SDIN1 C29 PCI AD10 D29 PCI AD13 A30 HDA RST B30 HDA SDINO C30 PCI AD12 D30 PCI AD15 A31 GND FIXED B31 GND FIXED C31 GND FIXED D31 GND FIXED A32 HDA BITCLK B32 SPKR C32 PCI AD13 D32 PCI PAR A33 HDA SDOUT B33 I2C CK C33 PCI C BE14 D33 PCI SERRZ A34 BIOS DISO B34 I2C DAT C34 PCI PERR D34 PCI STOP A35 THRMTRIP B35 THRM C35 PCI LOCK D35 PCI TRDY amp A36 USB6 B36 USB7 C36 PCI DEVSEL D36 PCI FRAME A37 USB6 B37 USB7 C37 PCI IRDY D37 PCI AD16 A38 USB 6 7 OC B38 USB 4 5 OC C38 PCI C BE24 D38 PCI AD18 A39 USB4 B39 USB5 C39 PCI AD17 D39 PCI AD20 A40 USB4 B40 USB5 C40 PCI AD19 D40 PCI AD22 A41 GND FIXED B41 GND FIXED C41 GND FIXED D41 GND FIXED A42 USB2 B42 USB3 C42 PCI AD21 D42 PCI AD24 A43 USB2 B43 USB3 C43 PCI AD23 D43 PCI AD26 A44 USB 2 3 OC B44 USB 0 1 OC C44 PCI C BE34 D44 PCI AD28
21. OS SETUP Main BIOS Setup This setup allows you to record some basic hardware configurations in your computer system and set the system clock BIOS SETUP UTILITY Main Advanced PCIPnP Security Chipset System Overview AMIBIOS Version 08 00 15 Build Date 09 15 10 Processor AMD Turion Neo N54L Dual Core Processor Speed 2200MHz Count 2 System Memory Size 1792MB System Time System Date 17 00 00 Thu 09 13 2010 Use ENTER TAB or SHIFT TAB to select a field Use or to configure system Time lt Select Screen 14 Select Item Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit Note If the system cannot boot after making and saving system changes with Setup the AMI BIOS supports an override to the CMOS settings that resets your system to its default Warning It is strongly recommended that you avoid making any changes to the chipset defaults These defaults have been carefully chosen by both AMI and your system manufacturer to provide the absolute maximum performance and reliability Changing the defaults could cause the system to become unstable and crash in some cases ET850 User s Manual 11 BIOS SETUP Advanced Settings This section allows you to configure and improve your system and allows you to set up some system features according to your preference BIOS SETUP UTILITY Advanced PciPnP Security Chipset
22. X0 PCIE RXO PEG RX5 PCIE TXO PCIE RXO PEG RX5 GND FIXED GND FIXED GND FIXED LVDS A0 LVDS BO PEG RX6 LVDS A0 LVDS BO PEG RX6 LVDS A1 LVDS B1 SDVO DATA LVDS A1 LVDS B1 PEG RX7 LVDS A2 LVDS B2 PEG RX7 LVDS A2 LVDS B2 GND LVDS VDD EN LVDS B3 RSVD A78 LVDS_A3 B78 LVDS_B3 C78 PEG RX8 D78 PEG TX8 A79 LVDS A3 B79 LVDS BKLT EN C79 PEG RX8 D79 PEG TX8 A80 GND FIXED B80 GND FIXED C80 GND FIXED D80 GND FIXED A81 LVDS A CK B81 LVDS B CK C81 PEG RX9 D81 PEG TX9 A82 LVDS A CK B82 LVDS B CK C82 PEG RX9 D82 PEG TX9 A83 LVDS I2C CK B83 LVDS BKLT Ctr C83 RSVD D83 RSVD A84 LVDS I2C DAT B84 VCC 5V SBY C84 GND D84 GND A85 GPI3 B85 VCC 5V SBY C85 PEG RX10 D85 PEG TX10 A86 KBD_RSD B86 VCC 5V SBY C86 PEG RX10 D86 PEG TX10 A87 KBD A20GATE B87 VCC 5V SBY C87 GND D87 GND A88 PCIEO CK REF B88 BIOS DIS1 2 C88 PEG RX11 D88 PEG TX11 A89 PCIEO CK REF B89 VGA RED C89 PEG RX11 D89 PEG TX11 A90 GND FIXED B90 GND FIXED C90 GND FIXED D90 GND FIXED A91 SPI POWER B91 VGA GRN C91 PEG RX12 D91 PEG TX12 A92 SPI MISO B92 VGA BLU C92 PEG RX12 D92 PEG TX12 A93 GPOO B93 VGA HSYNC C93 GND D93 GND A94 SPI CLK B94 VGA VSYNC C94 PEG RX13 D94 PEG TX13 A95 SPI MOS B95 VGA I2C CK C95 PEG RX13 D95 PEG TX13 A96 GND B96 VGA I2C DATA C96 GND D96 GND A97 NC B97 SPI CS amp C97 RSVD D97 PEG ENABLE A98 RSVD B98 RSVD C98 PEG RX14 D98 PEG TX14 A99 RSVD B99 RSVD C99 PEG RX
23. ffboard PCI IDE controller adapter card is installed in the computer You must specify the PCI Expansion slot on the motherboard where the offboard PCI IDE controller is installed This disables the onboard PCIIDE controller You must also specify the IRQs for this PCI IDE card IRQ Use the IRQ address to specify what IRQs can be assigned to a particular peripheral device Boot Settings BIOS SETUP UTILITY Advanced PCIPnP Boot Security Chipset Configure Settings during System Boot Boot Settings gt Boot Settings Configuration lt Select Screen 14 Select Item Change Field Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit gt Boot Device Priority gt Hard Disk Drives gt CD DVD Drives EE 20 ET850 User s Manual BIOS SETUP BIOS SETUP UTILITY Allows BIOS to skip certain tests while booting This will Quick Boot Enabled decrease the time Quiet Boot Disabled needed to boot the Boot Settings Configuration AddOn ROM Display Mode Force BIOS system Bootup Num Lock On PS 2 Mouse Support Auto lt Select Screen Wait for F1 If Error Enabled n Select Item Hit DEL Message Display Enabled Change Field Interrupt 19 Capture Disabled F1 General Help F10 Save and Exit ESC Exit Quick Boot This allows BIOS to skip certain tests while booting This will decrease the time needed to boot the system Quite Boot When disabled this displays normal
24. he ET850 COM Express Module comes on board with the AMD Athlon II Neo or AMD TurioT II Neo processors and powered by the AMD 785E SB820M chipset The chipset has built in Radeon HD4200 graphics engine with enhanced operating modes to enable excellent graphics performance in power and embedded applications The DirectX 10 1 feature lets you enjoy awesome graphics performance stunning 3D visual effects and dynamic Interactivity The board has one DDR3 800 SO DIMM socket supporting up to 4GB of system memory ET850 supports high speed connectivity with two SATA III four serial ports eight USB and a Gigabit LAN controller Dimensions of the CPU module are 95mm x 125mm ET850 Features AMD Athlon Neo Turion Neo Processors onboard up to 2 2GHz 1x DDR3 800 1333 SO DIMM Max 4GB Integrated VGA supports CRT amp LVDS Watchdog timer HD Audio 2x SATA II 1x GbE 8x USB 2 0 4x COM via baseboard ET850 User s Manual 7 INTRODUCTION Checklist Your ET850 package should include the items listed below e The ET850 CPU Module e Heat spreader for ET850 e This User s Manual e CD containing the following e Chipset Drivers e Flash Memory Utility Remarks After installing the heat spreader provided with the CPU module please install an additional heat spreader for better heat dissipation 95 50 62 uS Q 4 M3 P Lmm 18 62 42 54 9 86 9 125 2 9 3
25. ions Auto HD Audio Azalia Device Enabled Disable HD Onboard PIN Config Enabled Enable Azalia Front Panel Auto SDINO Pin Config Azalia SDIN1 Pin Config Azalia lt Select Screen SDIN2 Pin Config Azalia f Select Item SDIN3 Pin Config GPIO Azalia Snoop Disabled Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit E T 26 ET850 User s Manual BIOS SETUP BIOS SETUP UTILITY Chipset Onchip SATA Configuration Options Auto OnChip SATA Channel Enabled Disable OnChip SATA Type IDE Enable OnChip IDE Type Legacy IDE SATA IDE Combined Mode Enabled PATA Channel Config SATA as primary lt Select Screen 14 Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit OnChip SATA Type The options are 1 IDE 2 RAID 3 AHCI SS SS ET850 User s Manual 27 BIOS SETUP ee Exit Setup The exit setup has the following settings which are BIOS SETUP UTILITY Advanced PCIPnP Security Chipset Exit Exit system setup after saving the Save Changes and Exit changes Discard Changes and Exit Discard Changes F10 key can be used for this operation Exit Options Load Optimal Defaults Load Failsafe Defaults lt Select Screen 14 Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit Save Changes and Exit This option allows you to de
26. n battery is removed but it is not case with jumper pin 2 3 short J2 J3 COM Express Type 2 Connectors The Type 2 connectors come in two 220 pin 0 5mm pitch receptacles They include PCI IDE GBE and up to 22 general purpose PCIE lanes PCIE 0 5 and PCIE 16 31 For most Type 2 implementations it is expected that PCIE lanes 16 31 are used for graphics Hence they are designated PEG lanes 0 15 in the following table Modules implementing Pin out Type 2 such as the ET850 uses the pin out shown 6 ET850 User s Manual COM Express Type 2 Connectors INTRODUCTION Pin Signal Pin Signal Pin Signal Pin Signal A1 GND FIXED B1 GND FIXED C1 GND FIXED D1 GND FIXED A2 GBEO MDI3 B2 GBEO ACT C2 DE_D7 D2 IDE_D5 A3 GBEO MDI3 B3 LPC_FRAME C3 DE_D6 D3 IDE_D10 A4 GBEO LINK100 B4 LPC ADO C4 DE_D3 D4 IDE_D11 A5 GBEO LINK1000 B5 LPC AD1 C5 IDE D15 D5 IDE D12 GBEO MDI2 LPC AD2 DE D8 IDE D4 GBEO MDI2 LPC AD3 DE D9 IDE DO GBEO_LINK LPC_DRQO DE_D2 IDE_REQ GBEO_MDI1 LPC_DRQ1 IDE_D13 IDE_lOW GBEO_MDI1 LPC_CLK DE_D1 IDE_ACK GND FIXED GND FIXED GND FIXED GND FIXED GBEO MDIO PWRBTN IDE_D14 IDE_IRQ GBEO_MDIO SMB CK IDE IORDY IDE AO GBEO CTREF SMB DAT IDE IOR IDE A1 SUS S3 SMB ALERT PCI PME IDE A2 SATAO TX SATA1 TX PCI GNT24
27. phics Configuration Options Internal Graphics Mode UMA SIDEPORT Disable UMA Frame Buffer Size Auto UMA SIDEPORT Clock Speed 400MHz SIDEPORT GFX Engine Clock Override Disable UMA SIDEPORT UMA SP Interleave Mode Auto SP Power Management Auto SP NB Termination Disable SP Memory Termination Disable lt Select Screen SP CMD Hold Auto SP CMD Hold Auto fl Select Item Enter Go to Sub Screen Special Graphics Features Disabled F1 General Help FB Location Below 4G l F10 Save and Exit ESC Exit PANEL ID Selection 1024 x 768 24 bit RE ET850 User s Manual 25 BIOS SETUP OOO South Bridge Configuration BIOS SETUP UTILITY Chipset SouthBridge Chipset Configuration Options for SB GPP Por gt SP GPP Port Graphics Configuration gt SB Azalia Audio Configuration gt SB SATA Configuration lt Select Screen 14 Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit BIOS SETUP UTILITY Chipset SB GPP Port Configuration Options Disable SB GPP Function Enable Enable GPP Port Link Configuration 1 1 1 1 mode Unhide unused GPP ports Disable i GPP Link ASPM Disable lt Select Screen GPP Lane Reversal Disabled 14 Select Item Enter Go to Sub Screen NB SB PHY PLL Power Down Enable F1 General Help GPP PHY PLL Power Down Enable F10 Save and Exit ESC Exit BIOS SETUP UTILITY Chipset Onchip HD Azalia Configuration Opt
28. t Install Manager Version 03 00 0782 Installer Welcome Welcome Welcome Select Express or Custom Install and then click Next Express Custom Default Installation Location The folder C Program Files ATI Technologies does not exist Would you like to create this folder http ati amd com Bak Next gt Cancel 32 ET850 User s Manual DRIVERS INSTALLATION ATI Catalyst Install Manager Version 03 00 0782 Customize Install Select Components to Install Component Selection Name Version Customize ATI Display Driver M AMD SMBus Driver Mi avivo Select All 4 Current Version not Installed 3D acceleration control application that puts you in complete command of your ATI graphics processing unit GPU http ati amd com Next gt Cancel 4 Accept the license agreement to proceed with installation Reboot the computer when prompted for changes to take effect End User License Agreement End User License Agreement PLEASE READ THIS LICENSE CAREFULLY BEFORE USING THE SOFTWARE BY LISING THE SOFTWARE YOU ARE AGREEING TO BE BOUND BY THE TERMS OF THIS LICENSE 1 License The software accompanying this License hereinafter Software regardless of the media on which it is distributed are licensed to you by Advanced Micro Devices Inc AMD for use solely in conjunction with AMD hardware products purchased with the
29. tency Timer 64 Play PnP devices not Allocate IRQ to PCI VGA Yes y Palette Snooping Disabled required for boot if PCI IDE BusMaster Enabled our system has a Plu OffBoard PCI ISA IDE Card Auto y y A 9 and Play operating RQ3 Available system RQ4 Available RQ5 Reserved RQ7 Available RQ9 Available RQ10 Reserved RQ11 Available RQ14 Available RQ15 Available lt Select Screen DMA Channel 0 Available tL Select Item DMA Channel 1 Available Change Field DMA Channel 3 Available F1 General Help DMA Channel 5 Available F10 Save and Exit DMA Channel 6 Available t DMA Channel 7 Available ESC Exit Reserved Memory Size Disabled Clear VRAM Clear VRAM during system boot Plug amp Play O S This lets BIOS configure all devices in the system or lets the OS configure PnP devices not required for boot if your system has a Plug and Play OS Allocate IRQ to PCI VGA This assigns IRQ to PCI VGA card if card requests IRQ or doesn t assign IRQ to PCI VGA card even if card requests an IRO E ET850 User s Manual 79 BIOS SETUP pl m BM Jj M Palette Snooping When enabled PCI will allow VGA palette signals to go to the ISA bus PCI IDE BusMaster This function allows the BIOS to use PCI BusMastering for reading or writing to IDE drives OffBoard PCI ISA IDE Card This option specifies if an o
30. termine whether or not to accept the modifications and save all changes into the CMOS memory before exit Discard Changes and Exit This option allows you to exit the Setup utility without saving the changes you have made in this session Discard Changes This option allows you to discard all the changes that you have made in this session Load Optimal Defaults This option allows you to load the default values to your system configuration These default settings are optimal and enable all high performance features Load Failsafe Defaults This option allows you to load the troubleshooting default values permanently stored in the BIOS ROM These default settings are non optimal and disable all high performance features 28 ET850 User s Manual DRIVERS INSTALLATION Drivers Installation This section describes the installation procedures for software and drivers under the Windows XP and Windows Vista The software and drivers are included with the board If you find the items missing please contact the vendor where you made the purchase The contents of this section include the following VGA Drivers Installation rennes 30 Audio Drivers Installation ns 35 LAN Drivers Installation eene 36 Marvell LAN Drivers Installation IP401 B1 carrier board only 38 EE i ET850 User s Manual 29 DRIVERS INSTALLATION VGA
Download Pdf Manuals
Related Search