Operator, Parts and Service Manual Manufactured By
Contents
1. is found throughout this manual to draw your attention to instructions involving yourself and others working around this equipment e Failure to follow these instructions can result in Injury or Death This symbol means Attention Become Alert You are involved in your Safety Signal words used in this booklet Caution indicates a potentially hazardous situation that may result in injury Warning Indicates a potentially hazardous situation that could result in serious injury or death Danger Indicates a hazardous situation that needs to be avoided It is you the operator that has to be aware of these dangers If you have any questions not answered in this booklet please contact your dealer or M K Martin Enterprise Inc 3950 Steffler Rd Elmira On Ca N3B 2Z3 Tel 519 664 3695 Fax 519 664 3695 e mail sales mkmartin ca A Safety It s in your interest A Safety Guidelines Safety of the operator is one of our main concerns however it is up to you the operator to practice caution To avoid personal injury study the following precautions and insist that those working with you to follow them The MK Box Blade is a very basic piece of equipment Clear the area of people and especially children as your attention is concentrated on what the blade is doing rather than the surrounding space Try to stay aware of your surroundings When adjusting or replacing parts do not place yourself or other persons or a2. MK Martin Box Scraper Model 4485STD 560STD 448HD 560 HD 566 HD 672 HD 784 HD 672 DLX 784 DLX 896 DLX Operator Parts and Service Manual Manufactured By M K Martin Enterprise Inc 3950 Steffler Rd Elmira ON Ca N3B 2Z3 Tel 519 664 3752 1 855 664 3752 Fax 519 664 3695 e mail sales mkmartin ca Box Blade Table of Contents Warranty Sign off Sheet Safety Parts Operation Maintenance Bolt Torque KK Box Blade KK Box blade is ruggedly built with a reversible cutting edge to give you years of dependable service This blade is designed for maintaining the grade of your graveled yards and driveways and landscaping Warranty and Limitation of Liability All equipment is sold subject to mutual agreement that is warranted by M K Martin enterprise Inc hereafter called the company of any defects of material and workmanship The company shall not be liable for special indirect or consequential damage of any kind under this contract or otherwise The company s liability shall be limited exclusively to replacing or repairing without charge at its factory or elsewhere at its discretion any material or workmanship defects which become apparent within one year from date of purchase This will allow you one complete year of use in all conditions The company will have no liability for damages of any kind The buyer by the acceptance of the equipment will assume all liability for any damages whi
3. ch may be the result from the use or misuse by by the employees or others Warranty coverage is null and void if any unauthorized repairs or alterations are performed to this equipment Warranty is also null and void unless this warranty Registration is completely filled out and is on file at M K Martin Enterprise Inc This information is exclusively for registration and warranty purposes only It shall not be shared sold or otherwise divulged to 3rd parties To register please cut and mail the bottom or fax the whole page We will also accept electronic registration by e mail or through the website We need name address purchase date model and serial number For you record Purchase Date Y20 M Serial Please cut at dotted line and return this registeration form to the company via Mail Box Blade M K Martin Enterprise Inc 3950 Steffler Rd Elmira On Ca N3B 2Z3 Name or Purchaser sales mkmartin ca Name Purchase Date Y 20 M PG eee nnan Model rrmrrremnnnennonennoncnnonannoncnccnccnen Serial 000 III Postal Code Zip Code Annual Review Sign Off I We have reviewed and understand the use and operation of the MK Box Blade Date Name s Date Name s Safety Take Note This safety symbol
4. m 1 4 6 8 9 12 12 17 5 16 10 13 19 25 21 36 3 8 20 27 33 45 45 63 7 16 30 41 53 72 75 100 1 2 45 61 80 110 115 155 5 8 95 128 160 215 220 305 3 4 165 225 290 390 400 540 1 225 345 630 850 970 1320 Allen head cap screws are similar to SAE 8 quality O 8 amp These torques are for a reference only Not all these sizes and grades are necessarily used in this machine Bolts that are used as a pivot or hinge have to be used with a locknut therefore only tighten enough to secure the bolt and still allowing the part to rotate freely
5. ng for an extended period clean any dirt form the blade and coat any surfaces that have the paint worn off form using with a light coat of oil or rust protection MK Box Blade Care and Maintenance After 1st 5 hours check all nuts and bolts and retighten if required At 10 hours check all nuts and bolts and retighten if required Repeat at 5 hour intervals until all bolts have seated and stay tight Storage of MK Box Blade Store MK Grader Blade in a firm dry area and set on blocks if the area is not firm enough to support the equipment without sinking in Clean off all caked dirt and mud When Storing for a long period and rusting may be a problem coat the parts that the paint has worn off with oil or a rust preventative Wipe all excess oil off with a dry rag The Cutting Edge is reversible and after it shows considerable wear it can be reversed 1 Loosen all the Plowbolts 2 Remove all bolts except the bolts at each end 3 Tilt the Grader Blade on its back and remove the remaining bolts Note Cutting Edge is heavy Handle with care and use heavy gloves Bolt Torque As used on this equipment Bolt torque table shown below gives torque values for the various bolts used This chart is for non lubricated threads Replace with the same strength bolt Torque Specifications Torque values are identified by their head markings Diameter SAE2 SAE5 SAE 8 A Lb ft N m Lb ft N m Lb ft N
6. ng Edge 50276 2 5 HD 5 Ft Cutting Edge 50276 2 5 1 2 HD 5 1 2 Ft Cutting Edge 50192 2 6 HD 6 Ft Cutting Edge 50195 2 6 DLX 6 Ft Cutting Edge 50195 2 7HD 7 Ft Cutting Edge 50017 2 7 DLX 7 Ft Cutting Edge 50017 2 8 DLX 8 Ft Cutting Edge 50179 2 8 4ST Plowbolt 5 8x 1 1 2 OL 12 5 ST 14 5 HD 14 5 1 2 HD 16 6 HD 16 6 DLX 16 7 HD 18 7 DLX 18 8 DLX 20 Operating the Box Blade To attach the Box Blade to the tractor back the tractor to the Box Blade that is on level ground and fasten the lower 3ph link to the lower hitch mount Lengthen or shorten the top link until the link can be pinned on the top hitch mount This will ensure that the blade will be level with the ground and tractor when the blade is in working position To make the blade more aggressive when moving forward shorten the top link thereby tilting the blade ahead to make it dig in more For breaking hard soil the front shanks can be adjusted up or down by repositioning the keeper pin on top of the frame This blade has a reversed cutting edge at the back and can also be used in reverse Again the aggressiveness can be adjusted with the top link but in reverse Also note that when backing up that the angle of the tractor linkage will force the blade down into the media that is being scraped Use caution when doing this as extreme stresses can be created when doing this Storing the blade Park or store the blade on a firm surface concrete or wood planks in a dry place When stori
7. ny part of your body under a raised blade Do not use this machine while under the influence of drugs or alcohol Review the safety instructions annually This equipment should not be operated by children or those unfamiliar with the operation of the MK Box Blade Do not allow persons to operate this machine until they have read this manual and or were instructed by a qualified person A Please be careful with the extra weight on the back of the tractor It may be necessary to add extra weights to the front of the tractor to keep it balanced properly Box Blade Box Scraper Item Width Ft Description Part Oty 1 4 4 ft ST 50189 1 4 4ft HD 50197 1 5 5 ft ST 50025 1 5 5ft HD 50201 1 5 1 2 5 1 2 Ft HD 50172 1 6 6 ft HD 50162 1 6 6 ft DLX 50212 1 7 7ft HD 50014 1 7 7 ft DLX 50205 1 8 8Ft DLX 50156 1 2 PHS 1 4x3 4 c w fn OL 2 3 Manual Tube DJA70111 1 Item Width Ft Description Part Oty 4 4ST 3 4x 3 1 2 Bent pin wal385003 4 5 ST 4 5 HD 5 5 1 2 HD 5 6 HD 6 6 DLX 6 7 HD 7 7 DLX 7 8 DLX 8 5 4 ST Shank DJA45646 4 5 ST 4 5 HD 5 5 1 2 HD 5 6 HD 6 6 DLX 6 7 HD 7 7 DLX 7 8 DLX 8 6 4 ST 5 8 Nut OL 12 5 ST 14 5 HD 14 5 1 2 HD 16 6 HD 16 6 DLX 16 7 HD 18 7 DLX 18 8 DLX 20 7 4ST 4Ft Cutting Edge 50187 2 5 ST 5 Ft Cutti
Download Pdf Manuals
Related Search