Installation I User Manual
Contents
1. Pacific PR 9630 PR9636 Installation User Manual Hh ea EA AAS RANGE HOOD Warning ien nine EEE 1 Before using the NOOd csscceeeeeeeees 2 Installation se said acl Bh a eiaa 2 PIOCOGUIC ci2ss2 c dort E EEE R 3 Convertible Options ccceeeeeeeeteees 4 5 Operation amp Maintenance c 6 OMNES e220 a Nine seen eee 7 XP 02260 3 A WARNING 1 WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK OR INJURY TO PERSONS OBSERVE THE FOLLOWING a Use this unit only in the manner intended by the manufacturer If you have questions contact the manufacturer b Before servicing or cleaning unit switch power off at service panel and lock service panel to prevent power from being switched on accidentally When the service disconnecting means cannot be locked securely fasten a prominent warning device such as a tag To the service panel c Installation work and electrical wiring must be done by qualified person s in accordance with all applicable codes and standards Including Fire Rated construction d Sufficient air needed proper combustion and exhausting of gases through the flue chimney of fuel burning equipment to prevent back drafting Follow the heating equipment manufacturer s guideline and safety standards such as those published by the national Fire Protection Association NFPA and the American Society for Heating Refrigeration and Air2. Conditioning Engineers ASHRAE and the local code authorities e When cutting or drilling into wall or ceiling do not damage electrical wiring and other hidden utilities f Dusted fans must always be vented to the outdoors g If this unit is toy be installed over a tub or a shower it must be marked as appropriate for the application and be connected to a GFCL Ground Fault Interrupter protected branch circuit h NEVER place a switch where it can be reached from a tub or shower i WARNING TO REDUCE THE RISK OF FIRE USE ONLY MENTAL DUCT WORK j Make sure the power is off before installing wiring or maintenance 2 CAUTION For general ventilating use only Do not use to exhaust hazardous or explosive materials and vapors 3 WARING TO REDUCE THE RISK OF ARANGE TOP GREASE FIRE a Never leave surface units unattended at high settings Bou overs cause smoking and greasy spillovers that may ignite Heat oils slowly on low or medium settings b Always turn hood on when cooking at high heat or when cooking flaming foods c Clean ventilating fans frequently Grease should not be allowed to accumulate on fan or filter d Use proper pan size Always use cookware appropriate for the size of the surface element e Keep fan filters and grease laden surface clean f Use high hood setting on hood only when necessary g Don t leave hood unattended when cooking h Always use cookware and utensils appropriate f
3. C Right motor control I low II high speed C B A Maintenance 1 Always disconnect from power supply before cleaning 2 Clean both exterior and interior of the hood long lasting Do not use abrasive cleanser 3 Fan protection grille can be detached for cleaning by removing the screws with a screwdriver It must be reinstalled after clean 4 On retainers on the grille can also be detached for cleaning by turning the retainer in anti clockwise direction and reinstall at clockwise direction EAE AN 5 The oil cup in the centre of the hood for holding grease can be detached and cleaned regularly 6 Make a habit to turn on the hood before the ge stove to avoid high heat in the kitchen aa Anti clockwise to detach Ses Clockwise to install OTHERS 1 Repair service including replacement of main cord should only be carried out by manufacturer its service agent or a qualified technician It is dangerous for anyone other than the above mentioned people to perform repair service 2 Hazardous smoke fume generated from burning Towngas L P gas or and cooking must be discharged outside the kitchen through the exhaust pipe 3 Air ventilation inside kitchen must be maintained in good condition when range hood is in use 4 It is dangerous if cleaning is not carried out in accordance with the instructions specified in this user manual 5 Avoid using food products that p
4. efore installation 2 residue cups 1 6 starting collar 2 L brackets for direct wall 3 electrical wire connectors amp screws mount only 1 convertible transition collar 4 screws for L brackets 2 washer 2 small residue cups with 3 braces 1 3 1 4 x 10 starting collar 4 1 screw packaged separately 2 1 1 2 screw 2 back splash Package also includes 1 Care Maintenance and Installation Manual 2 Serial number label adhered on top of box Connect the power and switch on the motors and lighting system to check the operation Warning This appliance must be earthed INSTALLATION 1 Location Air turbulence from window door may reduce the effectiveness of hood as smoke from cooktop may not flow to the effective suction zone 25 cm from hood 2 Position The installation height is measured vertically from center of fan grille of hood to the to top of the stove The minimum installation height should not be less than 26 and the recommen ded height is 30 Avoid left right or front dropped inclination 3 Exhaust duct 6_inch diameter exhaust duct is recommended to use in order to maximize suction efficiency In case of 5 inch exhaust duct an adapter as enclosed in the packaging can be used In order to increase the efficiency of hood the length of exhaust duct must be minimized Min 26 Max 30 PROCEDURE 1 5 Find a suitable installation position of ho
5. od which should be next t o a window and can be cut to let the exhaust duct pass through If the exhaust duct has to pass through the wall particular attention must be paid to the structure of the wall as steel reinforcement may be embedded Mark the location of exhaust outlet hole then cut drill the hole with care Fix the position of hood and mark the position of the two hanging hooks Drive 2 steel nails into the selected wall with 3 mm maximum space leave behind for hanging the hood Adjust the hanging hooks on both sides of the hood and hang the hood on the steel nails then adjust the hood from side to side and from front and back to a horizontal position Follow the instruction print on the enclosed exhaust duct adapter and connect the exhaust duct adapter to the hood and window wall 5_inch or 6_inch duct can be used Plywood T LW gt w Exhaused d KY air tube J 5 A 3mm maximum limit Drill a hole for the air tube Drive 2 steel nails in on the upper cornerof the both side of the hood Adjust the hang hood and prepare to install Xx Must add the white ring on top of the range hood CONVERTIBLE OPTIONS This model is equipped with the option of a 6 vertical discharge 3 1 4x10 vertical discharge or 3 1 4x10 rear discharge Additional accessories are provided to convert between either of the above discharge methods e Standard back splash is incl
6. or the type and amount of food being prepared i To get the best performance the vertical clearance between the cook top and the range hood should range from 26 to 30 4 WARNING TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE OBSERVE THE FOLLOWING a SMOTHER FLAMES with a close fitting lid cookie sheet or metal tray then turn off the burner BE CAREFUL TO PREVENT BURNS If the flames do not go out immediately EVACUATE AND CALL THE FIRE DEPARTMENT b NEVER PICK UPAFLAMING PAN You may be burned c DO NOT USE WATER including wet dishcloths or towels a violent steam explosion will result d Use an extinguisher only if 1 You know you have aclass ABC extinguisher and you already know how to operate it 2 The fire is small and contained in the area where it stared 3 The fire department is being called 4 You can fight the fire with your back to an exit e WARNING TO Reduced The Risk Of Fire Or Electric Shock Do Not Use This Fan With Any Solid State Speed Control Device Based on Kitchen Fire Safety Tips published by NFPA Berore Usinc THE Hoop Packaging materials plastic bags polystyrene etc must be kept out of children s reach as they are potentially dangerous Installation must be carried out by a qualified technician Check the voltage on the rating plate which should corresponds to the voltage in your home Check the following accessories b
7. rodue flames under the Range Hood 6 During installation power supply must be disconnected
8. uded If desired install back splash to rear of range hood with screws provided after all duct converstion steps are complete 3 1 4x10 Vertical Discharge 1 Remove the pre mounted 6 transition 2 Place rectangular transition adaptor as adaptor on duct opening Leave shown over gasket and by first installing attached gasket in the original place 4 screws on half round section 3 Mount the 3 1 4x10 starting collar on top of the transition piece with the remaining screws CONVERTIBLE OPTIONS 3 1 14x10 Rear Discharge 4 At rear of range hood remove all screws on pre mounted rear rectangular cap and remove cap with gasket 6 Mount starting collar provided at rear discharge opening with gasket previously removed 5 Remove top pre mounted transition piece Leave attached gasket in its original place Option 1 for flush cabinet base Mount rectangular transition piece at opening with gasket as shown Mount rectangular cap previously removed on top of transition adaptor OPERATION amp MAINTENANCE Operation of your machine Always turn ON your hood before you begin cooking in order to establish an air flow in the kitchen Let motors run for a few minutes to remove cooking odour after you turn off the range This will help keep the kitchen fresh and clean A Light on off switch B Left motor control I low II high speed
Download Pdf Manuals
Related Search