USER'S MANUAL
Contents
1. air flow direction The horizontal louver can be moved at a range of 6 for each press or swing up and down automatically Please refer to the REMOTE CONTROLLER OPERATION MANUAL for details To set the horizontal air flow direction left right Move the vertical louver manually to adjust the air flow in the direction you prefer IMPORTANT Before adjusting the vertical louvers the supply power must be disconnected Vertical louver three places For some models the vertical louver can be adjusted by using the remote controller Please refer to the t REMOTE CONTROLLER OPERATION MANUAL for details ooe Do not operate the heat pump for long periods with the air flow direction set downward in cooling or dehumidifying Range mode Otherwise condensation may occur on the surface of the horizontal louver causing moisture to drop on to the floor or on furnishings Do not move the horizontal louver manually unless it is necessary Alwavs use the remote controller When the heat pump is started immediately after it was stopped the horizontal louver might not move for approximately 10 seconds Open angle of the horizontal louver should not be set too small as COOLING or HEATING performance may be impaired due to too restricted air flow area Do not operate unit with horizontal louver in closed position When the heat pump is connecte2. degrade the insulation It may cause an electric shock Do not put a pet or house plant where it will be exposed to direct air flow This could injure the pet or plant Do not place obstacles around air inlets or inside of air outlet t may cause failure of appliance or accident Ensure that the installation bracket of the outdoor appliance is not damaged due to prolonged exposure If bracket is damaged there is concern of damage due to falling of unit Use caution when unpacking and installing Sharp edges could cause injury O Ventilate the room well when used together with a stove etc An oxygen shortage may occur Do not use for special purposes Do not use this heat pump to preserve precision devices food pets plants and art objects It may cause deterioration of quality etc Turn off the main power switch when not using the unit for a long time It may cause failure of product or fire Always insert the filterg securely Clean filter once every two weeks Operation without filters may cause failure If water enters the unit turn the unit off and disconnect the power contact a qualified service technician OPERATING INSTRUCTIONS Parts names AG Indoor unit Indoor unit Air inlet l 1 Signal receptor 2 LCD Display window 3 Panel frame 4 Chassis 5 Front panel 6 Horizontal louver 7 Vertical louver 8 Air filter 9 Manual control
3. operation To achieve optimal performance please note the following Adjust the air flow direction correctly so that itis not directed on people Adjust the temperature to achieve the highest comfort level Do not adjust the unit to excessive temperature levels Close doors and windows on COOL or HEAT modes or performance may be reduced Use TIMER ON button on the remote controller to select a time you want to start your heat pump Do not put any object near air inlet or air outlet as the efficiency of the heat pump may be reduced and the heat pump may stop running Clean the air filter periodically otherwise cooling or heating performance may be reduced Do not operate unit with horizontal louvre in closed position Care and maintenance CARE AND MAINTENANCE Cleaning the Grille Case and Remote Controller e Turn the system off before cleaning To clean wipe with a soft dry cloth Do not use bleach or abrasives NOTE Supply power must be disconnectd before cleaning the indoor unit A cloth dampened with cold water may be used on the indoor unit ff it is very dirty Then wipe it with a dry cloth e Do not use a chemically treated cloth or duster to clean the unit e Do not use benzine thinner polishing powder or similar solvents for cleaning These may cause the plastic surface to crack or deform e Never use water hotter than 104 F to clean the front panel it could
4. you have set with timer Wait or cancel timer setting is incorrect Unit not cooling Inappropriate temperature Set temperature correctly For or heating setting detailed method please refer to Cooling heating Using remote control section models only room very well Air filter is blocked Clean the air filter while air flowing Doors or Windows are open Close the doors or windows out from the Air inlet or outlet of indoor or Clear obstructions away first then heat pump outdoor unit has been blocked restart the unit Compressor 3 minutes Wait protection has been activated If the trouble has not been corrected please contact a local dealer or the nearest customer service center Be sure to inform them of the detailed malfunctions and unit model Notes Do not attempt to repair the unit yourself Always consult an authorised service provider The design and specifications are subject to change without prior notice for product improvement Consult with the sales agency or manufacturer for details CS014U BPV1 202000100313 20100831
5. Before using your heat pump please read this manual carefully and keep it for future reference INVERTER SPLIT TYPE HEAT PUMP USER S MANUAL DIRECT AIR Read This Manual Inside you will find many helpful hints on how to use and maintain your heat pump properly Just a little preventative care on your part can save you a great deal of time and money over the life of your heat pump You ll find many answers to common problems in the chart of troubleshooting tips If you review the chart of Troubleshooting Tips first you may not need to call for service CONTENTS SOCIABLE REMARK Sere Ov Tcl a a aaa 2 SAFETY PRECAUTIONS Warning Caution OPERATING INSTRUCTIONS Parts names Operating temperature Manual operation Airflow direction control How the heat pump works CARE AND MAINTENANCE Care and maintenance OPERATION TIPS OO SPANO MPS SeT SSIS DSSS EASL E heh VRAIS r 12 TROUBLESHOOTING TIPS TERE EVES MGOUING HSS Waasia anina agigi anaana KARANAA nici russ AAAA AAAA ARRAT 14 A CAUTION Contact an authorised service technician for repair or maintenance of this unit Contact the installer for installation of this unit The heat pump is not intended for use by young children or invalids without supervision Young children should be supervised to ensure that they do not play with the heat pump it the power cord Is to be replaced replacement work shall be pertormed by
6. authorised personnel only nstallation work must be performed in accordance with the national wiring standards by authorised personnel only SOCIABLE REMARK When using this heat pump in the European countries the follow information must be followed DISPOSAL Do not dispose this product as unsorted municipal waste Collection of such waste separately for special treatment is necessary It is prohibited to dispose of this appliance in domestic household waste For disposal there are several possibilities A The municipality has established collection systems where electronic waste can be disposed of at least free of charge to the user B When buying a new product the retailer will take back the old product at least free of charge C The manufacture will take back the old appliance for disposal at least free of charge to the user D As old products contain valuable resources they can be sold to scrap metal dealers Wild disposal of waste in forests and landscapes endangers your health when hazardous substances leak into the ground water and find their way into the food chain SAFETY PRECAUTIONS To prevent injury to the user or other people and property damage the following instructions must be followed Incorrect operation due to ignoring of instructions may cause harm or damage The seriousness is classified by the following indications A WARNING This symbol indicates the possibility of death or serious inju
7. button 10 Remote controller holder 11 Remote controller 12 Connecting pipe 13 Drain hose Outdoor unit Outdoor unit 14 Connecting cable 15 Connective pipe 16 Stop valve Airinlet rear Air inlet side NOTE All the pictures in this manual are for explanation purpose only Your heat pump may be slightly different The actual shape shall prevail LCD display window 5 OPERATION display Illuminated when the heat pump is in operation Gi AUTO operation display w Illuminated during Auto operation i DEFROST operation display For Heating amp Cooling 1l model onlv iT ieee 1 OS OO 1 Illuminated when the heat pump starts defrosting automatically or when the warmair control feature is activated in heating operation TIMER display Illuminated during Timer operation on CLEAN AIR display on some models SS Illuminated when lonizer is activated Grad TURBO operation display 7 luminated when select TURBO function on cooling operation or on heating operation g DIGITAL DISPLAY Displayed the current setting temper ature or malfunction code when the heat pump is in operation When SELF CLEAN feature is activated it displays ore OPERATING INSTRUCTIONS amp amp amp FAN SPEED display Displayed the selected fan speed AUTO and three fan speed levels LOW S MED and HIGH SHS amp Operation Frequency display This display is separated into
8. cause deformation of discoloration Cleaning the air filter NOTE Supply power must be disconnectd before cleaning the indoor unit The air filters behind the front panel should be checked and cleaned once every 2 weeks or more often if necessary A clogged air filter will reduce cooling heating efficiency 1 Grasp both sides of the panel and pull it down the panel opened upward to an angle of 15 Push the panel upward and then lift it up 2 Take hold of the handle of the air filter and lift it up slightly to take it out from the filter holder then pull it downwards CARE AND MAINTENANCE Air filter SN emis 3 Remove the AIR FILTER from the indoor unit mlean the AIR FILTER once two weeks Clean the AIR FILTER with a vacuum cleaner r water then dry it up in cool place 4 Remove the Air Freshening Filter Optional filter Silver lon filter Bio filter Vitamin C filter 3M air purifier filter from its support frame Olean the air freshening filter at least once a month and replace it every 4 5 months Clean it with vacuum cleaner then dry it in cool place 5 Install the air freshening filter back into position 6 Insert the upper portion of air filter back into the unit taking care that the left and right edges line up correctly and place filter into position Maintenance If you plan to idle the unit for a long time perform the following 1 Operate the fan for about half a day t
9. d to power initial power the horizontal louver may generate a sound for 10 seconds this is a normal operation OPERATING INSTRUCTIONS How the heat pump works AUTO operation When you set the heat pump in AUTOmode it will automatically select cooling heating cooling heating models only or fan only operation depending on what Se is a temperature you have selected and the room temperature The heat pump will control roomtemperature Hour 4 hour automatically round the temperature point set by you ifthe AUTO mode is uncomfortable you can select desired conditions manually SLEEP operation 7 hours tim er off Cooling SLEEP operation When you push SLEEP button on remote controller during cooling heating cooling only type without or AUTO operation the heat pump will automatically increase cooling or decrease heating 2 F per hour for the first two hours then hold steady for the next 5 hours after that SLEEP operation 7 hours timer att A the unit will stop operation The fan speed will be auto matically controlled This feature can maintain the most Heating comfortable temperature and save more energy for you DRYING operation The fan speed will be automatically controlled under dry operation During the dry operation if the room temperature is lower than 50 F the compressor stops operation and restarts until the room temperature is above 54 F Optimal
10. e select the function it is recomm ended to run theheat pump under Cooling operation for about half an hour Once the Self Clean function is activated all TIMER setting will be cancelled During Self Clean operation when press the SELF CLEAN button on the remote controller again will stop the operation and turn off the unit automatically OPERATING INSTRUCTIONS NOTE This manual does not include Remote Controller Operations see the lt lt Remote Controller Instruction gt gt packed with the unit for details Operating temperature Temperature Cooling operation Heating operation Drying operation Room temperature gt 50 F 262 F lt 86 F 32 F 22 F 3 z S F_83 F 32 F _122 F Outdoor temperature 5 F 122 F For the models with low temperature cooling system CAUTION 1 If heat pump is used outside of the above conditions certain safety protection features may come into operation and cause the unit to function abnormally 2 Room relative humidity less than 80 If the air conditioner operates in excess of this figure the surface of the air conditioner may attract condensation Please sets the vertical air flow louver to its maximum angle vertically to the floor and set HIGH fan mode 3 Optimum performance will be achieved within these operating temperature Suggestion Forthe unit adopts an Electric Heater when the outside ambient temperature is below 0 C
11. efrosting Cooling and heating models only Frost may be generated on the outdoor unit during heat cycle when outdoor temperature is low and humidity is high resulting in lower heating efficiency of the heat pump During this condition air conditioner will stop heating operation and start defrosting automatically The time to defrost may vary from 4 to 10 minutes according to the outdoor temperature and the amount of frost build up on the outdoor unit A white mist coming out from the indoor unit e Awhite mist may generate due to a large temperature difference between air inlet and air outlet on COOL mode in an indoor environment that has a high relative humidity e A white mist may generate due to moisture generated from defrosting process when the heat pump restarts in HEAT mode operation after defrosting Low noise of the heat pump You may hear a low hissing sound when the compressor is running or has just stopped running This sound is the sound of the refrigerant flowing or coming to a stop e You can also hear a low squeak sound when the compressor is running or has just stopped running This is caused by heat expansion and cold contraction of the plastic parts in the unit when the temperature is changing A noise may be heard due to louver restoring to its original position when power is first turned on Dust is blown out from the indoor unit This is a normal condition when the heat pump has not been used for a long time or d
12. five zones The zones illuminate based on the compressor current frequency For example higher frequency will illuminate more zones Special function CLEAN AIR function on some models Air quality is the key to comfort this heat pump is equipped with lonizer lonizer can generate abundant anions to fill the room with refreshing and nature air Your whole family will enjoy a natural pure and healthy air everyday Follow Me function The remote control serves as a remote thermostat allowing for the precise temperature control at its location To activate the Follow Me feature point the remote control towards the unit and press the Follow Me button The remote display is actual temperature at its location The remote control will send this signal to the heat pump every 3 minutes interval until press the Follow Me button again If the unit does not receive the Follow Me signal during any 7 minute interval the unit will cancel the Follow Me mode automa tically SELF CLEAN function Function used after the Shut Down of cooling operation to clean the Evaporator and keep it as fresh for the next operation The unit will operate as following sequence FAN ONLY mode at Low fan speed Heating operation with LOW fan speed applicable to cooling amp heating modles only FAN ONLY operation Stop Operation Turn off Note This function is only available under COOL AUTO COOL FORCEDCOOL and DRY mode Befor
13. ithout Auto restart feature when the power restores the OPERATION indicator on the indoor unit starts flashing To restart the operation push the ON OFF button on the remote controller For the unit with Auto restart feature when the power restores the unit restarts automatically with all the previous settings preserved by the memory function 10 Lightning or a car wireless telephone operating nearby may cause the unit to malfunction Disconnect the unit with power and then re connect the unit with power again Push the ON OFF button on the remote controller to restart operation TROUBLESHOOTING TIPS Troubleshooting Tips Stop the heat pump immediately if one of the following faults occur Disconnect the power and contact the nearest customer service center the service people E0 E1 E2 E3 E4 E5 E6 E7 E8 or PO P1 P2 P3 P4 If the following code appears on the LED window disconnect the power and contact Trouble Fuse blows frequently or circuit breaker trips frequently Other objects or water penetrate the heat pump The remote controller won t work or works abnormally Other abnormal situations Malfunctions Cause What should be done Unit does not Power cut Wait for power to be restored start Unit may have become unplugged Check that plug is securely in wall receptacle Fuse may have blown Replace the fuse Battery in Remote controller may Replace the battery have been exhausted The time
14. o dry the inside of the unit 2 Stop the heat pump and disconnect power Remove the batteries from the remote controller 3 The outdoor unit requires periodic maintenance and cleaning Do not attempt to do this yourself Contact your dealer or servicer Checks before operation Check that the wiring is not broken off or disconnected e Check that the air filter is installed e Check if the air outlet or inlet is blocked after the heat pump has not been used for a long time Do not touch the metal parts of the unit when removing the filter Injuries can occur when handling sharp metal edges e Do not use water to clean inside the heat pump Exposure to water can destroy the insulation leading to possible electric shock e Vhen cleaning the unit first make sure that the power and circuit breaker are turned off OPERATION TIPS The following events may occur during normal operation 1 2 w gt 5 Protection of the heat pump Compressor protection e The compressor can t restart for 3 minutes after it stops Anti cold air Cooling and heating models only e The unt is designed not to blow cold air on HEAT mode when the indoor heat exchanger is in one of the following three situations and the set temperature has not been reached A When heating has just starting B Defrosting C Low temperature heating The indoor or outdoor fan stop running when defrosting Cooling and heating models only D
15. rectly rated Do not use the power cord Do not use the power cord near breaker or fuse close to heating appliances flammable gas or combustibles such as gasoline benzene thinner etc There is risk of fireorelectric It may cause fire and electric tmay cause an explosion or fire shock shock Ventilate roombefore operating r Do not disassemble or modify unit heat pump if there is a gas leakage from another appliance ie It may cause explosion fire and burns It may cause failure and electric shock P o When the air filter is to be removed do not touch the metal parts of the unit e It may cause an injury When the unit is to be cleaned switch off and turn off the circuit breaker Do not clean unit when power is on as it may cause fire and electric shock it may cause an injury Stop operation and close the window in storm or hurricane Operation with windows opened may cause wetting of indoor and soaking of household furniture Do not use strong detergent such as wax or thinner Use a soft cloth for cleaning Appearance may be deteriorated due to change of product color or scratching of its surface Do not place heavy object on the power cord and take care so that the cord is not compressed There is danger of fire or electric shock SAFETY PRECAUTIONS A CAUTION Do not clean the heat pump with water Water may enter the unit and
16. ry A CAUTION This symbol indicates the possibility of injury or damage to Popery J Meanings of symbols used in this manual are as shown below S Never do this r LA WARNING Connect with the power Do not operate or stop the Do not damage or use an properly unit by switching on or off unspecified power cord f the power Otherwise it may cause electric It may cause electric shock or fire It may cause electric shock or fire shock or fire due to excess heat due to heat generation generation Do not modify power cord O Do not operate with wet Do not direct airflow at length or share the outlet hands or in damp room occupants only with other appliances environment tmay cause electric shock or It may cause electric shock e This could damage your health fire due to heat generation Always ensure effective Do not allow water to run Always install circuit earthing into electric parts breaker and a dedicated power circuit No earthing may cause electric It may cause failure of machine No installation may cause fire shock or electric shock and electric shock O Disconnect the power if Do not drink water drained J Do not open the unit strange sounds smell or from heat pump during operation smoke comes from it tmay cause fire and electric It contains contaminants and tmay cause electric shock shock could make you sick Use the cor
17. uring first use of the unit A peculiar smell comes out from the indoor unit This is caused by the indoor unit giving off smells permeated from building material from furniture or smoke The heat pump turns to FAN only mode from COOL or HEAT For cooling and heating models only mode When indoor temperature reaches the temperature setting on heat pump the compressor will stop automatically and the heat pump turns to FAN only mode The compressor will start again when the indoor temperature rises on COOL mode or falls on HEAT mode For cooling and heating models only to the set point OPERATION TIPS Koj Dripping water may generate on the surface of the indoor unit when cooling in a high relatively humidity relative humidity higher than 80 Adjust the horizontal louver to the maximum air outlet position and select HIGH fan speed Heating mode For cooling and heating models only The heat pump draws in heat fromthe outdoor unit and releases it via the indoor unit during heating operation When the outdoor temperature falls heat drawn in by the heat pump decreases accordingly At the same time heat loading of the heat pump increases due to larger difference between indoor and outdoor temperature If a comfortable temperature can t be achieved by the heat pump we suggest you use a supplementary heating device Auto restart function Power failure during operation will stop the unit completely For the unit w
18. we strongly recommend you to keep the machine plugged in order to guarantee it running smoothly Manual operation Manul operation can be used temporarily in case the remote controller is disable or maintenance necessary NOTE The unit must be turned off before operating the manual control button If the unit is operational continue pressing the manual control button until the unit is off Grasp both sides of the panel and pull it down the panel opened upward to an angle of 15 Push the panel upward and then lift it up One press of the manual control button will lead to the forced AUTO operation If press the button twice within five seconds the unit will operate under forced COOL operation Manualicontrol 0 Autercoal Close the panel firmly to its original batiri position CAUTION e This button is used for testing purposes only You had better not choose it e Torestore the remote controller operation use the remote controller directly a OPERATING INSTRUCTIONS Airflow direction control e Adjust the air flow direction properly otherwise it might cause discomfort or cause uneven room m temperatures Adjust the horizontal louver using the remote controller A Adjust the vertical louver manually Range To set the vertical air flow Up Down direction Perform this function while the unit is in operation Use the remote controller to adjust the
Download Pdf Manuals
Related Search