Installation and User's Manual “$1.1:
Contents
1. OPERATION FUNCTION PEL ro s IKEYPAD 1 255 CAM Using for entering camera ID les 1 99 5 MENU Gamera OSD MENU ON olol oje MENU Camera OSD MENU OFF x ol olo sey Move tothe sub menu in OSO MENU O O BACK Move to the upper menu in OSDMENU O O o KEYPAD 1 285 PRESET PRESET Execution 6 1 256 11 84 o KEYPAD 1 255 PRESET o ese 1 64 Press it button longly kina aloka laknati i op KEYPAD 1 255 Fi feel eens PRESET Delete x x x lo KEYPAD 1 8 PATTN PATTERN Execution o uana o KEYPAD 1 8 PATT N d isos hus egy PATTERN Setting o oa na x SORT SORT AUTO KEYPAD 1 8 SWING SWING Execution i SWNGi SWNG PAN SEQ SEQ KEYPAD 1 8 GROUP GROUP Execution amaran SCAN Save Patioms x o o x ru Same as F2functon n OSO MENU X X Change to the Aux Mode x x x o Same as Entor function in OSD MENU X X X o Same as F3 funcionin OSD MENU X X Fa Rosat function Press it button shorty X X x o Reset function Press it button longy X X Factory Select Camera D e oe ele KEYPAD 0 9 direction key 2 4 68 InOSOMENY X O 6 Using for AUX kay KINI xo GAM Move to the sub menu in OSD MENU X X CLR Move to the upper menu in OSD MENU X X PEL PELCO PROTOCOL PANAS PANASONIC N NEW C CONVENTIONAL PROTOCOL m SC3100 PTZ CO2. 4 General Connection SC3100 PTZ CONTROLLER 3 Name and Function of each part 1 Camera Setup part 1 PRESET Used when moving to Preset Point PRESET Setting Move the camera to the desired position using joystick or camera control button Enter PRESET No Press PRESET button for 2 seconds then the current position is set to PRESET No PRESET Execution Enter PRESET No Press PRESET button shortly then the camera moves to the specified PRESET position 2 PATTEN It stores jog operation and PRESET operation patterns executed for a specified period and allows executing them again PATTERN Setup Enter desired PATTERN No b Pross PATT N button for 2 seconds long CEN C E Store cancel the pattern using NEAR FAR key button applicable to the supported camera only PATTERN Execution Enter desired PATTERN No 8 Press PATT N button shorty then the desired PATTERN is executed 3 SWING This function can select 2 Preset positions remembered on Preset Setup and automatically Monitor repeatedly SWING Soup tt is possible to directly set up it within camera OSD menu applicable to the supported camera only SWING Execution Enter desired SWING No 8 Press SWING button shorty then desired SWING is executed 4 GROUP It provides repeated sequential monitoring with specified speed and waiting time by combining PRESET PATTER
3. Never expose the product to rain or water SC3100 PTZ CONTROLLER 1 Introduction and Features 1 Introduction 2 Features 2 Product Coi 1 Product Configuration 2 RS 232 Pin Layout D 3 Termination DIP Switch 4 General Connection 3 Name and Function of 1 Camera Setup Part 2 Numeric Pad 3 General Control Part 4 Camera Control Par 5 System LOCK 6 Menu Control Part cooooco yy 2 Controller interface Device Setting Mode 3 Main Menu for Setting Controller interface Device 4 Joystick Setting Menu 5 User Mode Setup Menu 6 DVR Device Setup Menu 7 Menu Structure for Controlling Controller System 8 Controller System Setting Mode 9 Main Menu of Controller System Setting 10 User Logo Setup Menu 11 FACTORY SET Setup Menu 6 Controller Firmware upgrade 1 Controller Firmware upgrade 7 Operation List 1 Operation List Product Appearance and Specifications 1 Product Appearance e D Product Specifications m SC3100 PTZ CONTROLLER 1 Introduction and Features 1 Introduction SC3100 is a dedicated CCTV controller consisting of 28 function keys 3 axis joystick and LCD display in order to directly control devices such as Speed Dome Camera DVR etc 2 Features One controller is capable of commanding up to 255 devices including ParvTill Zoom camera With RS 485 communication it provides long distance r
4. When ku byak oy down ect a dct on aspect Cun itis possible to input 2 lines of user logo Position the cursor on up down arrows and move the joystick upward downward then the IH EC cursor moves to each line SC3100 PTZ CONTROLLER 11 FACTORY SET Setup Menu D After selecting main menu for setting controller system and titing Joystick right then a menu is displayed as shown on the right CLR ALL DATA It initializes controller to the default factory condition CLR EDIT DATA It initializes all of date except for Joystick and PROTOCOL menu 6 Controller Firmware Upgrade 1 Controller Firmware upgrade TECHNOLOGY Inc It is possible to execute firmware upgrade of the controller at PC through RS 232 Port Firmware upgrade application is not provided when purchasing the equipment and only original buyer can obtain the new firmware upgrades QD Check if the controller to be upgraded is connected to PC Q2 Open It opens upgrade file cnb File Path When opening upgrade file it shows the file path Messages It indicates type of upgrade file System Init When it is selected the controller is initialized to the default factory condition Status It indicates progress of upgrade D Progress It indicates transmission status of upgrade SC3100 PTZ CONTROLLER 7 Operation List
5. CONTROLLER 1 Introduction and Features 1 Introduction SC3100 is a dedicated CCTV controller consisting of 28 function keys 3 axis joystick and LCD display in order to directly control devices such as Speed Dome Camera DVR etc 2 Features One controller is capable of commanding up to 255 devices including ParvTill Zoom camera With RS 485 communication it provides long distance remote control up to 1 2km It supports different protocols for each channel Pelco D Pelco P Samsung Elec Panasonic Itis able to control various kinds of functions of the devices such as Preset Pattern Swing Group etc Using joystick it can control ParvTilt speed of the camera Adopting 4 Line Text LCD it provides functions including menu control company logo input etc Using function keys for convenience it is possible to easily operate functions such as Preset Pattern Swing and Group It provides password setup of the administrator tis possible to use up to 4 slave controllers It provides Firmware Upgrade using RS 232 It provides USB Mouse funcion m SC3100 PTZ CONTROLLER PRECAUTIONS Safety Precautions 1 Careful Reading of User s Manual Carefully read all the safety precautions and operation methods of the product before operating 2 Keeping of User s Manual The safety and operating manual should be retained for future reference 3 Attachment Do not use atta
6. indicates protocol of the currently selected ID PELCO D PELCO P SAMSUNG ELEC PANASONIC SPEED It indicates data rate of the currently selected ID 2400 4800 9600 19200 38400 DATA PARITY and STOP BIT are fixed to BBIT NONE and 1BIT respectively JOY STICK It sets up sensitivity center position and fixed speed of joystick See joystick setup menu STOP PACKET I indicates number of stop packets to be sent when transmitting joystick and function commands D MODE It sets up user mode See User mode Setup menu 8 SLAVE DEV It sets up slave device See DVR Device Setup menu 8 MOUSE SET It sets up mouse speed When mouse function is used SC3100 can t control the speed dome D EXIT It stores interface device setup menu and moves to initial screen 4 Joystick Setup Menu D When selecting main menu for setting controller interface device and tilting joystick right a menu as shown on upper right figure is displayed CENTER It sets up sensitivity of joystick 10 15 20 25 30 ORIGIN SET When selecting this menu and tilting joystick right a menu as shown on middle right figure is displayed It sets up CENTER POSITION of joystick e Position the joystick at the center and store the position en selecting main menu GS for setting controller interface device and ing joystick left a menu as shown on lower right figure is displayed it operates in L ow speed M medium speed F fast speed rega
7. N and SWING functions GROUP Setup It is possible to directly set it up within camera OSD menu applicable on the supported camera only GROUP Execution Enter desired GROUP No Press GROUP button shortly then desired GROUP is executed SC3100 PTZ CONTROLLER 5 F1 USB Mouse function OrvOft Press it button longly Refer to the section titled Operation List 6 F2 Rear to the section titted Operation List 2 Numeric Pad Numbers 0 9 Used for entering camera ID or other functions lt p Q CAM Used for storing data specified when entering ID ogg CLR Used for deleting camera ID and other entered function ERIS Bi GG oo 3 General Control part rere D IRIS Open Cloos Used to adjust iris of zoom camera B6 applicable on the supported camera only D TELE WIDE Used for executing zoom operation of camera TELE Mouse left button function WIDE Mouse right button function D NEAR FAR Used for controlling focus when using zoom lens applicable in the supported camera only 4 Camera Control part D Joystick Used for controlling ParvTil Zoom operations of camera Tilt UP Moves camera upward Tilt Down Moves camera downward Pan Left Moves camera left Pan Right Moves camera right Zoom Tele Executes TELE zoom Zoom Wide Execute WIDE zoom 5 System LOCK It is located at the upper right side of keyboard co
8. NTROLLER 8 Product Appearance and Specifications 1 Product Appearance Iie 2 Product Specifications Category T 83100 Par Tiit RS 485 Remote control up to 1 2km H DVR interface RS 485 USB we USB USB Mouse function support Protocol Peco D Peico P Samsung Eiec Panasonic LCD Display 20 x 4 Character LCD PTZ Control Joystick 3 Axis Twist Zoom Sub keyboard Max 4 Devices Type Asynchronous Serial 1 Start Bit No Parity 1 Stop Bit RS 405 Specification Transmission Type Half Duplex Date Rate 2400 38400 bps RS 252 Specification D SUB 9P Firmware Upgrade Operation Power 12V DC 9V Battery USB PC MaxiSOmA Operation Temperature 10 50 C 60 Dimensions 400W x 200 H x 99 97 D mm Weight About 1 24kg Excluding Adaptor SC3100 PTZ CONTROLLER re ce X Design and specifications are subject to change without notice Ver 0906 3810 01898
9. T button for 2 seconds then password input message is displayed Password input Refer to the section tied Controller interface Device Setup Mode 9 Main Menu of Controller System Setting D PASSWORD It sets up password to be used to enter into controller interface device and system setup menu Default is 00007 Itis set when all of 4 digits are entered SLEEP TIME It indicates when LCD Backlight turns on It requires keypad input with larger than 10s and applies only when D BACKLIGHT is ON BUZZER It indicates BUZZER ON OFF of the system LOGO It allows the user to input logo directly Refer to user logo setup menu FACTORY It sets the controller to default factory condition 8 OP MODE It indicates Master Slave mode In case of using one master and several slaves connected slaves shall be set to Slave Mode SC3100 allows maximum 4 slaves to be connected BACKLIGHT It indicates whether using Backlight of LCD monitor ON Backlight turns off when specified time on SLEEP TIME has passed OFF Backlight turns off AUTO When pressing key button Backlight tums on for 5 seconds i DUMMY When using Master Slave be sure to set only master controller ON EXIT It stores system setup menu and reboots the system 10 User Logo Setup Menu D After selecting main menu for setting controller system and selecting USER menu using joystick a menu is displayed as shown on the right
10. chments not recommended by the equipment manufacturer as they may cause hazards 4 Installation Conditions Do not use this product under wet or humid conditions 5 Installation Do not install the product in unstable position or put on unstable location The product may cause Severe injury to person or serious damage on the product if improperly mounted Use fixture sold with the product or recommended by the manufacturer Attach the product according to installation method of the manufacture and be sure to use the parts recommended by the manufacturer 6 Power Supply This product is able to operate under rated power supply Precautions for Use Use of Product jeck if wiring and power connection are correct before using If any abnormal state or malfunction is observed during operation stop using and immediately contact the supplier Handling Do not disassemble the product and be careful not touch the parts within it In order to avoid any damage on the product do not drop or apply vibration and impact on it Installation and Storage Do not install the product in the place with temperature exceeding operating range Avoid installing the product in moist or dusty place Avoid installing the product on radioactive place It may cause failure on the parts Avoid installing the product in the place having strong magnetic field or electric signal Avoid installing the product in the place with strong vibration
11. emote control up to 1 2km It supports different protocols for each channel Pelco D Pelco P Samsung Elec Panasonic Itis able to control various kinds of functions of the devices such as Preset Pattern Swing Group etc Using joystick it can control ParvTilt speed of the camera Adopting 4 Line Text LCD it provides functions including menu control company logo input etc Using function keys for convenience it is possible to easily operate functions such as Preset Pattern Swing and Group It provides password setup of the administrator tis possible to use up to 4 slave controllers It provides Firmware Upgrade using RS 232 It provides USB Mouse funcion SC3100 PTZ CONTROLLER 2 Product Configuration and System Diagram 1 Product Configuration Oca Main Body Users Manua USB CABLE pd CABLE Option Upon purchasing the product be sure to check if it contains all of the items listed below KEYBOARD CONTROLLER EA USB CABLE USER S MANUAL E 2 System Diagram 20 1 System connection USB Port in cate of using Sub keyboard n is possible to contol using SC3100 PTZ CONTROLLER 2 RS 232 Pin Layout D SUB MALE 5 1 Supported Firmware Upgrade function using direct cable 3 Termination DIP Switch RS 485 Termination ON RS 485 Termination OFF
12. ntroller and used to protect the controller being operated by other user Press it for 2 seconds then it enters into LOCK status and released when entering password C3100 PTZ CONTROLLER 6 Menu Control Part D MENU Press it shortly then it enters into camera OSD menu And MENU message is displayed on LCD monitor E _ Press it shorty again then texts out of camera OSD menu EE applicable on the supported protocol only 2 BACK Move to the upper menu In OSD MENU SET Move to the sub menu In OSD MENU Press it for a specified period with numeric keys then it enters into function setup mode 7 Battery Part D As shown on right figure push the battery cover down to the inside Ne direction and pull then battery cover is opened SS 4 PTZ Control 1 Power on D Before turning on the controller power turn on power for external dovices connected to the contoller frst C Press a power button on the rear leh side of controller GD As tho vorson logo and main screen message are displayed on LCD monitor the controller is on enabled status 2 Initial Screen Display D PROTOCOL indicates PROTOCOL of camera selected currently 2 PTZ ADDR Indicates ID of camera selected current D SPEED Indicates data rate of camera selected current NUM INPUT Itis displayed only when entering number with numeric Pad and indicates the entered number 1D 3 Camera ID Setup D Enter desired
13. number torm numeric pad Selected number is displayed ex NUM INPUT 001 D Press CAM button then camera ID is set to the selected number It s possible to select number within 1 255 if the number is out of selectable range camera ID wil not be set SC3100 PTZ CONTROLLER 4 Joystick Camera Operation Method Using joystick itis possible to operate pan Tit movement of camera i 3 t 3 8 3 l g 5 Controller Setup 1 Menu Structure for Setting Controller Interface Device Using joystick It is possible to operate zoom movement of camera C3100 PTZ CONTROLLER 2 Controller Interface Device Setting Mode It is a menu to set up controller interface devices Press number 1 on intial screen and SET button for 2 seconds then password input message is displayed Enter default 0000 set on factory or other password defied by the user arbitrary When password matches interface device setup menu is displayed If password does not match 3 times or it is not entered for 10 seconds it moves to the initial screen 3 Main Menu for Setting Controller Interface Device D NUMBER It indicates camera ID selected currently It may be a number within 1 285 and set up using joystick and numeric pad However in case of using numeric pad it is required to enter 3 digits TYPE It indicates the currently selected device SC3100 supports PTZ only 9 PROTOCOL It
14. rdless to tilting of the joystick o SC3100 PTZ CONTROLLER e 5 User Mode Setup Menu D When selecting main menu for setting controller interface device and tilting joystick right a menu as shown on upper right figure is displayed MONITOR It sets up user monitor number and DVR channel number CAM ID it sets up the camera ID to be connected to the monitor It may be a number within 1 255 and set up using joystick and numeric pad However in case of using numeric pad it is required to enter 3 digits SAVE Tilting joystick left EXIT Tilting joystick right 6 DVR Device Setup Menu D When selecting main menu amp for setting controller interface device and tilting joystick right a menu as shown on upper right figure is displayed PROT It sets up the protocol of the DVR PELCO D PELCO P SAMSUNG ELEC PANASONIC SPEED It sets up the data rate of the DVR 2400 4800 9600 19200 38400 7 Menu Structure for Controlling controller System PASSWORD Password Setup SLEEP TWE Waiting Time Setup C O8 gama L 2r SET LOGO System set Ari SET ao A 2 LU FACTORY Lqetatzaton ot Sting J gt ABA OP MODE i Rm m SSS Ca BACKLIGHT Gesagusan _ J gt C oN D GED lt SC3100 PTZ CONTROLLER 8 Controller System Setting Mode This menu sets up controller system D Press number 2 on initial screen and SE
15. stallation and Storage Do not install the product in the place with temperature exceeding operating range Avoid installing the product in moist or dusty place Avoid installing the product on radioactive place It may cause failure on the parts Avoid installing the product in the place having strong magnetic field or electric signal Avoid installing the product in the place with strong vibration Never expose the product to rain or water SC3100 PTZ CONTROLLER 1 Introduction and Features 1 Introduction 2 Features 2 Product Coi 1 Product Configuration 2 RS 232 Pin Layout D 3 Termination DIP Switch 4 General Connection 3 Name and Function of 1 Camera Setup Part 2 Numeric Pad 3 General Control Part 4 Camera Control Par 5 System LOCK 6 Menu Control Part cooooco yy 2 Controller interface Device Setting Mode 3 Main Menu for Setting Controller interface Device 4 Joystick Setting Menu 5 User Mode Setup Menu 6 DVR Device Setup Menu 7 Menu Structure for Controlling Controller System 8 Controller System Setting Mode 9 Main Menu of Controller System Setting 10 User Logo Setup Menu 11 FACTORY SET Setup Menu 6 Controller Firmware upgrade 1 Controller Firmware upgrade 7 Operation List 1 Operation List Product Appearance and Specifications 1 Product Appearance e D Product Specifications m SC3100 PTZ
16. www cnbtec com 2 z H 5 G z Installation and Us m SC3100 PTZ CONTROLLER PRECAUTIONS Safety Precautions 1 Careful Reading of User s Manual Carefully read all the safety precautions and operation methods of the product before operating 2 Keeping of User s Manual The safety and operating manual should be retained for future reference 3 Attachment Do not use attachments not recommended by the equipment manufacturer as they may cause hazards 4 Installation Conditions Do not use this product under wet or humid conditions 5 Installation Do not install the product in unstable position or put on unstable location The product may cause Severe injury to person or serious damage on the product if improperly mounted Use fixture sold with the product or recommended by the manufacturer Attach the product according to installation method of the manufacture and be sure to use the parts recommended by the manufacturer 6 Power Supply This product is able to operate under rated power supply Precautions for Use Use of Product jeck if wiring and power connection are correct before using If any abnormal state or malfunction is observed during operation stop using and immediately contact the supplier Handling Do not disassemble the product and be careful not touch the parts within it In order to avoid any damage on the product do not drop or apply vibration and impact on it In
Download Pdf Manuals
Related Search