User Guide
Contents
1. and is able to support a weight of 30 kgs for each unit Safety chain Mounting plate Eye bolt 2 Technical Specification Power supply AC 120V 60HZz or 230V 240V 250V 50 60Hz Lamp Discharge lamp MSD 250W GyY9 5 Optical system Standard 13 focused beam angle Focus adjustable by DMX control Shutter Dimmer Blackout 0 100 smooth dimming and strobe speed variable 1 10 flashes per second Gobo wheel Independent gobo wheel with 7 gobos plus open gobos are interchangeable 4 metal gobos 2 glass gobos and 1 effect gobo 3 additional metal gobos and 2 effect gobos are included Gobo wheel rotates with variable speed Shaking effect included Color wheel Independent color wheel with 9 dichroic mirrors plus white Color wheel rotates with variable speed giving rainbow effect Prism 3 facet prism rotates in both directions at variable speeds 5A Movement Pan 540 in 2 8 second Tilt 270 in 1 6 second DMX Channels Standard DMX512 signal addressing and can be controlled by any universal DMX controller Channel 1 Pan motion Channel 9 Gobo Channel 2 Tilt motion Channel 10 Gobo Rotation Channel 8 Reset Channel 16 Reset Dimension 360mm x 397mm x 503mm L x W x H Weight 26 kg 6 Troubleshootino Following are a few common problems that may occur during operation Here are some suggestions for easy troubleshooting A The unit does not work no light and the2. and wipe it with a lint free cloth before installation 3 The lamp generates UV radiation Never operate the lamp without appropriate shielding 4 When burning the lamp operates at high pressure and there is a slight risk of arc tube rupture The risk increases with age temperature and improper handling of the lamp Do not use the lamp any longer than its specified life 5 Make sure the lamp is located in the center of the reflector for the best spot Adjust lamp position by screws A B and C DMX 612 Configuration 2 Channel 14 Channel 15 Channel 16 Pre programmed Pre programmed recuse Pattern Beam Pattern Reset Channel 13 Channel 11 Channel 12 Prism Prism Rotation Prism Rotation Slow Stop Slow Q Prism Rotation Fast 7A o Stop i Channel 14 Pre programmed show pattern 1 DMX value 0 31 the fixture is still controlled by DMX control 2 For DMX Value above 31 all the DMX control will be invalid The fixture will run the pre programmed show patterns Pan Tilt movement ii Channel 15 Pre programmed beam pattern One can select the beam pattern only when the pre programmed show pattern is activated iii For DMX Reset put DMX value of CH 8 amp CH 16 to 255 5 4 DMX512 Configuration DMX 612 Configuration 1 Channel 2 Tilt Pan Tilt inir Shutter _ Speed select Shaking chamat Gobo Shaking 8A an Channel 10 nel 7 Gobo ex mrs ton ow T Gob
3. fan does not work 1 Check the connect power and main fuse 2 Measure the mains voltage on the main connector 3 Check the power on LED B Not responding to DMX controller 1 DMX LED should be on If not check DMX connectors cables to see if link properly 2 If the DMX LED is on and no response to the channel check the address settings and DMX polarity 3 If you have intermittent DMX signal problems check the pins on connectors or on PCB of the unit or the previous one 4 Try to use another DMX controller 5 Check in the DMX cables run near or run alongside to high voltage cables that may cause damage or interference to DMX interface circuit C Some units don t respond to the easy controller 1 You may have a break in the DMX cabling Check the LED for the response of the master slave mode signal 2 Wrong DMX address in the unit Set the proper address D No response to the sound 1 Check the unit that is not receiving DMX signal 2 Check microphone to see if it is good by tapping the microphone E One of the channels is not working well 1 The stepper motor might be damaged or the cable connected to the PCB is broken 2 The motor s drive IC on the PCB might be out of condition F The lamp is cutting out intermittently 1 The lamp is not working well Check the main voltage either too high or too low Internal temperature may be too high Check and if necessary replace the fan on the head 5 5 DMX512 Connection The DMX51
4. 2 is widely used in intelligent lighting control with a maximum of 512 channels 1 2 3 4 DMX512 120 ohm 1 4 W COMMON INPUT Termination reduces signal errors and to avoid signal transmission problems and interference Itis always advisable to connect a DMX terminal Resistance 120 ohm 1 4W between pin2 DMX and pin3 DMX of the last fixture 1 If you use a controller with 5 pins DMX connector you need to use a 5 to 3 pin adapter 2 At last unit the DMX cable has to be terminated with a terminator Solder a 120 ohm 1 4W resistor between pin 2 DMX and pin 3 DMX into a 3 pin XLR plug and plug it in the DMX output of the last unit 3 Connect the unit together in a daisy chain by XLR plug from the output of the unit to the input of the next unit The cable cannot be branched or split to a Y cable DMX512 is a very high speed signal Inadequate or damaged cables soldered joints or corroded connectors can easily distort the signal and shut down the system 4 The DMX output and input connectors are pass through to maintain the DMX circuit when power is disconnected to the unit 5 Each lighting unit needs to have an address set to receive the data sent by the controller The address number is between 0 511 usually O amp 1 are equal to 1 6 The end of the DMX512 system should be terminated to reduce signal errors 7 3 pin XLR connectors are more popular than 5 pins XLR 3 pin XLR Pin 1 GND Pin 2 Ne
5. Moving Head Spot Professional Lighting Technology LINKABLE eS MASTER SLAVE WW BEGLEC COM User Guide Please read these instructions carefully before use 2A TABLE OF CONTENTS Safety Instruction Technical Specification 2 1 Inserting Exchanging rotating gobos Lamp How To Set The Unit 4 1 Control Panel 4 2 Main Function How To Control The Unit 5 1 Master Slave Built In Preprogrammed Function 5 2 Easy Controller 5 3 Universal DMX Controller 5 4 DMX512 Configuration 5 5 DMX512 Connection Troubleshooting Fixture Cleaning 1 Safety Instruction Please read carefully the instruction which includes important A N information about the installation usage and maintenance WARNING Please keep this User Guide for future consultation If you sell the unit to another user be sure that they also receive this instruction booklet Unpack and check carefully there is no transportation damage before using the unit Before operating ensure that the voltage and frequency of power supply match the power requirements of the unit The unit is designed for use with the MSD 250W Do not use any other type of lamp It s important to ground the yellow green conductor to earth in order to avoid electric shock The unit is for indoor use only Use only in a dry location The unit must be installed in a location with adequate ventilation at least 50cm from adjacent surfaces Be sure that no ventilation slo
6. ew belt H by going through all connecting wires that from the arm to base and through the bridge for correct position 7 Set up the gear axis to the bridge and screwed it Note do not press the belt 8 Put the belt around the axis gear and motor gear 9 Plug all the connect wires C that form the arm to PC board and igniter 10 Adjust the pan home position 11 Screw the base housing cover B 4A Warning To prevent or reduce the risk of electrical shock or fire do not expose the unit to rain or moisture Never touch bulb with bare fingers as it is very hot after using Hot lamp explosion hazard Do not open the unit within five minutes after switching off Do not start on the unit without bulb enclosure or housing are damaged The housing the lenses or the ultraviolet filter must be replaced if they are visibly damaged Do not look directly at the light while the bulb is on Caution There are no user serviceable parts inside the unit Do not open the housing or attempt any repairs yourself In the unlikely event your unit may require service please contact your nearest dealer Installation The unit should be mounted via its mounting system as shown below on the bottom of the base Use clamps to fix the unit to truss Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating Always ensure that the structure to which you are attaching the unit is secure
7. gative signal Pin 3 Positive signal 5 pin XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal 6A Luminous intensity Beam Angle 13 Deg 6470 Distance m 2 1 Inserting Exchanging rotating gobos DANGER Install the gobos with the device switched off only Unplug from mains before changing gobos Open the cover by loosening the fastening screw at the sides of the cover If you wish to use other forms and patterns as the standard gobos or if the gobos are to be exchanged remove the fixation ring with an appropriate tool Remove the gobo and insert the new gobo Press the fixation ring together and insert it in the front of the gobo CAUTION Never unscrew the screws of the rotating gobo as the ball bearing will otherwise be opened A Because of its high internal pressure there might be a risk that the Discharge lamp would In case of replacement of the lamp or maintenance do not open the fixture within 15 minutes until the unit cools down after switching off explode during operation The lamp emits intense UV radiation which is harmful to the eyes and skin The high luminance of the arc can cause severe damage to the retina if looks directly at the lamp Discharge lamp MSD 250W 1 Always switch off the main supply and never handle the lamp or luminaries when is hot 2 Do not touch the bulb with bare hands If this happens clean the lamp with denatured alcohol
8. ink Use DOWN and UP button to select the show 1 or z show 2 mode Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds To go back to the functions without any change press the MENU button again Press the MODE button from the easy controller to select the 2 i show 1 or show 2 mode When the LED is off it is in SHOW 1 mode and blinking in SHOW 2 mode art Show 1 mode Fixture is placed on the floor Tilt movement angle 210 _ 2 C Show 2 mode Fixture is fixed under ceiling Tilt movement angle 90 E 4 Ll III slave Mode Press the MENU button up to when the Sit is shown on the display Pressing ENTER button and the display will blink Use DOWN and UP button to select the mio normal or 2 light show mode Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds To go back to the functions without any change press the MENU button again l LITI Blackout Mode 2 is shown on the display Pressing ENTER Press the MENU button up to when the m button and the display will blink Use DOWN and UP button to select the m m yes blackout or C no blackout mode Once the mode has been selected press the ENTER button t
9. just l to 512 channel so that the units can receive DMX signal PSE Self Test thh Fixture Hours Press the MENU button up to when the Haar is shown on the display Pressing ENTER COL Reset button and the display will blink Use DOWN and UP button to change the DMX512 address CILL Once the address has been selected press and keep ENTER button pressed up to when the display stops blinking or storing automatically 8 seconds later To go back to the functions without any change press the MENU button again Please refer to the following diagram to address your DMX512 channel for the first 4 units 5 How To Control The Unit You can operate the unit in three ways 1 By master slave built in preprogram function 2 By easy controller 3 By universal DMX controller No need to turn the unit off when you change the DMX address as new DMX address setting will be effected at once Every time you turn the unit on it will show AE16 on the display and move all the motors to their home position and you may hear some noises for about 20 seconds After that the unit will be ready to receive DMX signal or run the built in programs 5 1 Master Slave Built In Preprogrammed Function J II You can select blackout mode 2110 jn 3 OO yes blackout or 0 no blackout mode while the unit is turned on By linking the units in master slave connection the first unit will control the other units to give an au
10. nds To go normal or back to the functions without any change press the MENU button again Display Inversion It is good for you to install the unit on the floor or under ceiling Press the MENU button up to when the is blinking on the display Use the ENTER button to change to the mode oor i display inversion It will automatically store after 8 seconds Or press the ENTER button again return to the mode an the MENU button display normal To go back to the functions press Display normal mode for the fixture putting on the floor Display inversion mode for the fixture fixing under ceiling 11A IL Focus Adjust Press the MENU button up to when the 0u js blinking on the display Pressing ENTER button the unit will focus on tilt 90 and then the unit will focus on pan 0 pan 90 pan180 pan270 in every pressing ENTER button Use DOWN and UP button to adjust focus To go back to the functions press the MENU button again Lleol Self Test Press the MENU button up to when the CEIC js blinking on the display Pressing ENTER button and the unit will run self test by built in program To go back to the functions press the MENU button again Fixture Hours Press the MENU button up to when the rnc a js blinking on the display Pressing ENTER button and the display will sh
11. o Rotation Slow Stop Slow Q Goba Rotation Fast 0 Normal Stop 4 How To Set The Unit 4 1 Control Panel DMX OUT Ao SENSITIVITY MENU DOWN ENTER DMX IN REMOTE CONTROL Display To show the various menus and the selected functions LED DMX DMX input present Master mode Button Remote controller input By connect to the 1 4 microphone jack to control the unit for Stand by Strobe Next and Show 1 Slow Show 2 function Sensitivity To adjust the sound receiving sensitivity Microphone To receive audio signal for sound activation DMX input output For DMX512 link use 3 pin XLR plug cable to link the unit together 4 2 Main Function 5 2 Easy Controller To select any of the pre set functions press the MENU button up to when the required one is shown on the display Select the function by ENTER button and the display will blink Use The easy remote controller is used only in master slave mode By connecting to the 1 4 DOWN and UP button to change the mode Once the required mode has been selected microphone jack of the first unit you will find that the remote control on the first unit will control press the ENTER button to setup or it will automatically return to the main functions without all the other units for Stand by Strobe Next Strobe and Show 1 Slow Show 2 functions any change after idling 8 seconds To go back to the functions without any change press the MENU button The main functions a
12. o setup or automatically return to the main functions without any change after 8 seconds To go back to the functions without any change press the MENU button again _ L LI ILI Color Mode Press the MENU button up to when the LLTO is shown on the display Pressing ENTER button and the display will blink Use DOWN and UP button to select the G normal or split color mode Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds To go back to the functions without any change press the MENU button again Pan Inversion Press the MENU button up to when the LON jg shown on the display Pressing ENTER button and the display will blink Use DOWN and UP button to select the pan inversion mode Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds To go Mio normal or back to the functions without any change press the MENU button again Tilt Inversion Press the MENU button up to when the ELE jg shown on the display Pressing ENTER button and the display will blink Use DOWN and UP button to select the G tilt inversion mode Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 8 seco
13. ow the number of working hours of the unit To go back to the functions press the MENU button again ti 1 JLI Reset Press the MENU button up to when the 2C C is blinking on the display Pressing ENTER button and all channels of the unit will return to their standard position To go back to the functions press the MENU button again DMX RESET Set DMX value of channel 8 and channel 16 to 255 then all channels of the unit will return to their standard home position
14. re shown below 1 STAND BY To blackout all the units 2 FUNCTION STROBE NEXT STROBE Under SHOW 1 and SHOW 2 mode the units will strobe in three different ways a Strobe in different gobos and colors Adar Cie DMX512 Address Setting b Synchronous strobe in white color a Gh Show Mode Show 1 c Two light strobe in white color Shd Z 4 A r l am c Show Mode Show 2 Under SLOW mode press FUNCTION button to choose desired co mag a9 Slave Mode Normal color and gobo It will change ten colors and then change one HG dH 1 C1 clan Slave mode 2 Light Show gobo mma 2 oo Blackout Mode Yes Blackout ee ta tia Blackout Mode No Blackout 3 MODE SHOW 1 SLOW SHOW 2 ema oe Normal Color When the LED is off it is in SHOW 1 mode and blinking in SHOW OE Split Color 9A 2 mode The units movement Pan Tilt amp Gobo Color is sound aS no Pan Normal activated If the LED on it is in SLOW mode Pan Tilt is sound roan MENU Pan Inversion activated but Gobo Color wheel are static controlled by Next mc Tilt Normal PELE button Te Tilt Inversion i gF Display Normal 1 oor 4GP Display Inversion 5 3 Universal DMX Controller If you use a universal DMX controller to control the units you have to set DMX address from 1 row Focus Ad
15. sing normal glass cleaning fluid e Always dry the parts carefully e Clean the external optics at least every 20 days Clean the internal optics at least every 30 60 days EC Declaration of Conformity We declare that our products lighting equipments comply with the following specification and bears CE mark in accordance with the provision of the Electromagnetic Compatibility EMC Directive 89 336 EEC EN55014 1 1993 EN61000 3 2 1995 EN61000 3 3 1995 EN55014 2 1997 CATEGORY II EN61000 4 2 1995 EN61000 4 3 1995 EN61000 4 4 1995 EN61000 4 5 1995 EN61000 4 6 1995 EN61000 4 11 1994 amp Harmonized Standard EN60598 1 1993 Safety of household and similar electrical appliances Part 1 General requirements Following the provisions of the Low Voltage Directive 73 23 EEC and 93 68 EEC EC Declaration of Conformity We declare that our products remote controller comply with the following specification and bears CE mark in accordance with the provision of the Electromagnetic Compatibility EMC Directive 89 336 EEC EN55015 1993 EN50082 1 1997 EN61000 3 2 1995 EN61000 3 3 1995 G If The pan belt is broken 1 Turn off the main power Unscrew all the screws A and open the base housing cover B Unplug all the connect wires C that from the arm to PC board and igniter Unscrew the screws D that fix the bridge E Unscrew the screws F that fix the axis gear G O oa A O N Change a n
16. tomatic sound activated synchronized light show This function is good when you want an instant show You have to select ah 2 C show 2 mode by easy controller Its DMX input jack will have nothing plugged into it and Its master LED will be constantly on and sound LED will flash to the music The other L IIL units will have to set in slave mode 2 and select normal or cL on 2 light show mode Their DMX cables plugged into the DMX input jacks daisy chain and the slave show 1 or LED lights will constantly on 2 light show Lit slave mode i oe m L In mio means the unit works normally and 4 means 2 light show In order to create a great light show you can set cl Gin on the second unit to get contrast movement to each other even if you have two units only lI DMX512 Address Setting 10A Press the MENU button up to when the HOOT is shown on the display Pressing ENTER button and the display will blink Use DOWN and UP button to change the DMX512 address Once the address has been selected press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds To go back to the functions without any change press the MENU button again Lire TIItLI Show Mode Press the MENU button up To when the is showing on the display Pressing ENTER button and the display will bl
17. ts are blocked Disconnect main power before fuse lamp replacement or servicing Replace fuse lamp only with the same type Make sure there are no flammable materials close to the unit while operating as it is fire hazard Use safety chain when fixes this unit Don t handle the unit by taking its head only but always by taking its base Maximum ambient temperature is Ta 40 C Don t operate it where the temperature is higher than this Unit surface temperature may reach up to 85 C Don t touch the housing bare hand during its operation and allow about 15 minutes to cool down before replacing bulb or serving as the unit could be very hot In the event of serious operating problem stop using the unit immediately Never try to repair the unit by yourself Repairs carried out by unskilled people can lead to damage or malfunction Please contact the nearest authorized technical assistance center Always use the same type spare parts Don t connect the device to any dimmer pack Do not touch any wire during operation as high voltage might be causing electric shock 3A 7 Fixture Cleanino The cleaning of internal and external optical lenses and or mirrors must be carried out periodically to optimize light output Cleaning frequency depends on the environment in which the fixture operates damp smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit s optics e Clean with soft cloth u
Download Pdf Manuals
Related Search