User guide
Contents
1. If this problem has not appeared from the beginning pay attention to following questions e Have you used appropriate fuels e Is there windy stormy weather outside e Can t you handle compensation air is the lower air control box open Linnatuli Oy Yrjonalhontie 13 FI 21420 Lieto Tel 358 0 20 7413 123 Fax 358 0 2 4870 305 www linnatuli com e Have you opened the glass door slowly e Is the glass door loose How about the sealing of the glass door If you answered Yes to all of these questions take contact to your fireplace supplier manufacturer Is the wood consumption too high If this problem has not appeared from the beginning pay attention to following questions e Have you reduced the amount of the compensation air e Is the glass door closed properly e Do you burn right amount of wood e Are logs dry enough Moisture under 20 If you answered Yes to all of these questions take contact to your fireplace supplier manufacturer More information For more information take contact to your fireplace supplier manufacturer Linnatuli Oy Yrjonalhontie 13 FI 21420 Lieto Tel 358 0 20 7413 123 Fax 358 0 2 4870 305 www linnatuli com Anna burning guide Open the damper and in some cases the ignition plate too If flue hasn t been used for a long time only in models with top and upper connection Adding wood Heat storing Referred amount of fire wood o 1 batch2. 5 cm air gap for old flames either to the left or to the right side see picture Open the glass hatch carefully and add 4 0 kg wood Close the hatch as fast as possible When embers are red hot the air control under the ash box should be turned fully open to the right if not yet done When red coals turn black close the air control under the ash box and close the air control over the glass hatch Close the damper Linnatuli Oy Yrjonalhontie 13 Lieto 21420 Finland Tel 358 20 7413 123 Mail linnatuli linnatuli com
3. upon Remember to open door slowly when adding woods When door is opened quickly especially bigger doors may leave smoke to the room Ignition plate can be opened for a few moments when door is opened so possible negative pressure do not make easily problems for draught Ignition plate must be closed right after closing the fireplace door The most stable final heating result can be reached with burning one batch by morning and one by evening Close the damper after embers have turned from red to black When the fireplace will not be used for a long time the damper lower air control unit and air control slides over the fireplace door must be closed When usage of the fireplace continues it must be checked that flue is not blocked by for example birds nest If there is a very bad weather flues of the fireplace can be heated with for example hairdryer or paper so the draught is better Cleaning the ash The ash box must be cleaned at times so burning air can get through the grating Air makes grating colder and it can be damaged if the air is not given Clean glass doors from the appliance according to manufacturer s guide How to clean ash box Detach lower air control by pulling carefully from both sides of the air controls cover After approx 5 cm long air control is detached the ash box can be seen Pull ash box out and carry ashes to the metallic bin After two days ashes can be moved to the place designed for ash It is recommended to cl
4. 28 11 2013 LI N NATU LI ANNA User guide NOTE BEFORE USING THE FIREPLACE Always when using a fireplace the replacement air must be taken care of 1 kg of firewood needs approx 8 10m of air for combustion Let fireplace get dry with fireplace door and smoke damper open at least 2 3 weeks Drying can be faster when using a fan heater Make sure before igniting first batch of woods that fireplace s flue channels are dry If there s moisture in channels drying must be continued without fire Before burning the first batch of wood must be ensured that sweeping hatches are in right places These places can be found for example from the layer pictures of the installing manual Start heating using very small batches of firewood approx 0 5 kg once a day for a week First batch must be burned with ignition plate open only top connection model After 7 days amount of wood can be added approx 1 kg once a day At the drying phase leave the smoke damper open so all moisture can exit freely Fireplace s too fast heating may damage the fireplace and shorten its working life Notice that if a fireplace has been long time without usage the heating must be started carefully so the moisture that has accumulated to elements won t harm the appliance In any case the moisture cannot be condensed to inner surfaces of the fireplace while heating Remember CO danger Do not close the smoke damper too soon Fireplace is not suitable f
5. 6 0 kg lt 0 5 kg wood o 2 batch 4 0 kg lt 1 0 kg wood o 3 batch 4 0 kg lt 1 0 kg wood Lay all woods lengthwise to the nest s bottom Woods of the first layer should have weight of 500 g at max Size of these woods should be approx 6x5 x 30cm Lay rest of the first batch lengthwise as evenly as possible The top of the wood pile should be at the centre of the fire nest Lay heavier woods to AN the bottom and lighter woods to the top Smallest woods approx 1 x 1 5 x 30 cm should be at the top Primer or birch bark can be used to ignite the first batch Put primer over the wood pile and ignite the nest with a lighter If the ignition plate is open close it after few minutes Adjust the air control over the glass hatch fully open By doing this the glass stays clean longer Adjust the air control under the ash box if wanted o The more airis given under the ash box the faster woods burn and waste heat is formed o The less air is given under the ash box the more ash and bigger embers are left o Linnatuli recommends that the air is fully open under the ash nest Black lines touch each other So more air can enter to the nest and toxic gases will burn in the burning chamber Add the 2 and the 3 nest when the former nest has been burning approx 58 minutes 3 nest 35 minutes after adding the 2 nest Try to add all wood to the center of the fire nest Woods must be added so that they leave about
6. Y ENERGY DENSITY kWh kg kWh loose m kWh pile m Pine 4 15 810 1360 Spruce 4 10 790 1320 Birch 4 15 1010 1700 Alder 4 05 740 1230 Aspen 4 00 790 1330 Wood pellet moist lt 10 p 4 8 3 1 Wood briquette moist lt 10 p 4 8 Never use wet wood or too small draught because flue channels can get dirty and as a result can be dangerous chimney fire In case of chimney fire the local fire department must be called immediately Chimney fire Too wet or low quality wood as a fuel can send sparks through the appliance all the way to the chimney These sparks can influence a chimney fire With regular sweeping this kind of cases are very uncommon If the chimney is on fire can it be seen in flames in chimney s blaze in sparkles with heavy smoke through chimney and harsh smell of a smoke Also chimney s sides feel hotter than normal In the situation mentioned above it is important to react right Call fire department and report for a fire Inform also the chimney sweeper Take flammable objects away from around the chimney Before the fire department has arrived do not throw any water on the appliance Temperatures in chimney fire can rise up to 1300 C The water thrown to the flames would evaporate immediately and for example 10 liters of water were to become 17 m of steam The pressure that would be formed could tear the whole chimney Storing firewood Woods are recommended to be stored in wintertime Woods
7. are suggested cut to logs so drying is faster It may take even 2 3 years before woods have dried to the level where the moisture content has dropped to 15 20 Logs from fresh wood are not to be maintained for example in the basement or in the garage Do not even wrap woods with plastic for example tarp because air cannot run through the logs at then Store logs in an area that has a good air conditioning and is protected from the rain Linnatuli Oy Yrj6nalhontie 13 FI 21420 Lieto Tel 358 0 20 7413 123 Fax 358 0 2 4870 305 www linnatuli com Using the fireplace Begin with opening a smoke damper and an ignition damper if necessary in cases when chimney is cold or fireplace hasn t been used in a long time Lay logs and primers sparsely to the backside of the fire nest so that they leave clear gap between a fireplace door Open lower air control unit at least 3 cm and air control slides over the fireplace door according to Burning guide page 8 It is recommended to ignite the batch from the top center This way fine particle emissions are smaller Bringing woods near to the fireplace one day before burning is also recommended For creating a draught the fireplace door must be closed right after ignition After woods have ignited and draught has been created the ignition plate may be closed When there are only embers left adding second batch is possible Check recommended wood amounts for your fireplace from the table
8. d glass door gets loose In this case turn nut s arm back to the gap and help it staying in the right place and direction through tightening Tighten glass door at least twice per half year Terms of guarantee Do not make any changes to the capacitive fireplace without manufacturer s approval Changes in the fireplace may lead lapse of the guarantee Faulty parts must be replaced with parts approved by the manufacturer FAQ The glass door gets black quickly and uneven If this problem has not appeared from the beginning pay attention to following questions e Have you used appropriate fuels e Is there windy stormy weather outside e Can t you handle compensation air is the lower air control box open e Does the door soot quickly in a half hour If you answered Yes to all of these questions take contact to your fireplace supplier manufacturer Batch catches fire poorly and very slowly If this problem has not appeared from the beginning pay attention to following questions e Have you used appropriate fuels e Is there windy stormy weather outside e Can t you handle compensation air is the lower air control box open e All the air control switches are as open as possible e Is there a 0 5 1 cm gap between an inner element and the ash boxes upper side If you answered Yes to all of these questions take contact to your fireplace supplier manufacturer Smoke comes inside the room when burning the fireplace
9. ean ashes before igniting next batch in the fireplace Put ash box back to the same place and position Ash box must be pushed against the back of the ash layer so the air gaps between ash box and inner element won t be closed Take care that there s no bigger embers left under the ash box Now the air control unit can be attached back to its place by pushing or tapping it carefully Draught of the flue Modern fireplaces require more from the flue compared to old fireplaces If flue is wrong size of or seedy draught can suffer very much Draught consists of flue gas temperature of exterior temperature of 4 Linnatuli Oy Yrjonalhontie 13 FI 21420 Lieto Tel 358 0 20 7413 123 Fax 358 0 2 4870 305 www linnatuli com weather of brought air amount and measurements of the fireplace Connection to the flue must be tall enough compared inner measures of the flue CE shield demands that draught of the flue is 12 25 Pa The draught of the flue gets better when height of the flue grows flue gets warmer or more air is guided to the fire nest from the room If flues diameter is too big or flue has wrong height take contact to a professional Take always care that fireplaces temperature class do not cross flues temperature class Cleaning and handling the fireplace Sweeping of fireplace must be done at least once a year Sweeping hatches can be found behind the ash box Detach air control unit and ash box from the fireplace before swee
10. ignition plate and leave the damper plate open This way all heat runs straight to the flue and out through it When combustion does not have any oxygen it will weaken Let logs burn until the end Pay attention to safety distances to igniting materials incl furniture and fire woods when using the fireplace All igniting materials at immediacy of the fireplace must be protected from the fire Obey local laws and orders Do not leave the fireplace alone whilst burning or close the damper before all the embers are flamed out This case can cause carbon monoxide poisoning Linnatuli Oy Yrjonalhontie 13 FI 21420 Lieto Tel 358 0 20 7413 123 Fax 358 0 2 4870 305 www linnatuli com Keep the glass door of the fireplace generally closed so smoke does not pervade into the room The glass door can be opened during adding wood and during cleaning the ash Handling packaging waste Deliver packaging waste of the fireplace to the dump s waste burning point This way all material will be recycled in the form of new energy The EPS material and cover plastics may not be burned in the fireplace Tightening the glass door Screws of the glass door must be tightened at times Tighten screws with a screwdriver after burning few batches Make sure at the same time that the screws tightening nut s arm is still attached to outer element s inner surface If the nut is not fastened properly it drops out from the gap between inner and outer element an
11. or shared flue There must always be flue for each fireplace Compensation air Compensation air must be taken care of so that good draught can be ensured Extractor hood and central vacuum cleaner are not recommended to be used while using a fireplace if ventilation system does not include pressure leveling system for example ventilator s fireplace switch Ventilator s fireplace switch adds room s excess pressure only temporarily If necessary a window can be opened for the time of ignition After woods have ignited the draught usually improves so much that window can be closed Make sure that ventilation holes of the fireplace stay clean It is recommended to test the motility of the ventilation holes at times Beginning Let fireplace get dry with fireplace door and smoke damper open at least 2 3 weeks Drying can be faster when using a fan heater Make sure before igniting first batch of woods that fireplace s flue channels are dry If there s moisture in channels drying must be continued without fire Before burning the first batch of wood it must be ensured that sweeping hatches are in right places These places can be found for example from the layer pictures of the installing manual Start heating with very small batches of firewood approx 0 5 kg once a day for a week First batch must be burned with ignition plate open only top connection model After 7 days amount of wood can be added approx 2 kg once a day Lea
12. ping Sweeping of fireplace and flue must always be done by professional Clean nest from the ash always before igniting the next burning Make sure that air can flow freely from every air gap to the fire nest This way fire reaction stays as clean as possible It is recommended to maintain installation and usage manuals with layer pictures for sweeper Sweeping guide The cheek flue channels and back flue channels are to be swept through sweeping hatches on sides of ash nest It is recommended to use pipe cleaner with spring made of nylon More specific pictures of the structure is found installation manual of the fireplace Guide for sweeping the flue can be found flue s manufacturer s user guide Cleaning the glass door Soot must be swept off the glass often enough so it won t burn into the glass The easiest way to clean door s glass is to dip wet newspaper in the ashes in the nest and swipe the soot off carefully with it Safety Never use the fireplace with another fireplace attached to the same flue at the same time Fireplace heats up through the burning period and even after it When burning bigger batches even the plaster surface can become hot Glass door becomes burning hot while woods are burning Glove belongs in to the fireplace delivery Use this glove always when using the fireplace If it feels that fireplace is overheated close air holes in glass door and slide air control unit to the left close it Open the
13. ve the smoke damper open at the drying phase so all moisture can exit freely Fireplace s too fast heating may damage the fireplace and shorten its working life Notice that if fireplace has been long time without usage heating must be started carefully so the moisture that has accumulated to elements won t harm the appliance In any case the moisture cannot be condensed to inner surfaces of the fireplace while heating Permitted fuels Use most preferably as dry wood as possible Burning trashes card board paper burnable packaging materials in the fireplace is not recommended Do not burn coal briquettes or other materials incl liquid fuels that may include toxic gases in the fireplace Wooden briquettes and pellets are allowed in small quantities Any national or local regulations and codes of practice shall be complied with Find maximum wood quantities for each fireplace from the table below Linnatuli Oy Yrjonalhontie 13 FI 21420 Lieto Tel 358 0 20 7413 123 Fax 358 0 2 4870 305 www linnatuli com WOOD AMOUNT max d MAXIMUM HEIGHT FIREPLACE kg WOOD LENGTH cm OF BATCH cm Maria REG 2 24 2 25 20 Juhana 4 5 3 3 30 25 Kulma Juhana 4 5 3 3 30 25 Iso Juhana 7 34 3 33 28 Aino 6 2 5 2 5 30 25 Anna 6 4 4 33 28 Anna tunnel model 6 34 3 33 28 Johannes 2 5 2 5 2 54 2 5 33 25 Iso Johannes 6 3 5 3 5 33 28 FUEL HEAT VALUE ENERGY DENSIT
Download Pdf Manuals
Related Search