Elcometer 195 Säberg Drill Operating Instructions
Contents
1. 55188 5 RELATED EQUIPMENT Elcometer produces a wide range of adhesion gauges and associated inspection equipment Elcometer 195 users may also benefit from the following Elcometer products e Elcometer 141 Paint Inspection Gauge e Elcometer 406 Mini Glossmeter e Elcometer 107 Cross Hatch Cutter For further information contact Elcometer your local supplier or visit www elcometer com2. Elcometer 195 Saberg Drill Operating Instructions elcomeler elcometer is a registered trademark of Elcometer Instruments Ltd All other trademarks acknowledged Copyright Elcometer Instruments Ltd 1996 2006 All rights reserved No part of this Document may be reproduced transmitted transcribed stored in a retrieval system or otherwise or translated into any language in any form or by any means electronic mechanical magnetic optical manual or otherwise without the prior written permission of Elcometer Instruments Ltd Doc No TMA 0082 Issue 02 Text with Cover No 6059 elcometer CONTENTS Section Page 1 About your drill 44 mainides naeh are anne 2 2 Wsingiyourdrill nen aaa a 4 3 Maintenance au 000 wa eea sata maa a a a a en a u ama 5 4 Spareparts time aaa ceed a ER en En 5 5 Related equipment 2 cece eee eee eee eee ee nennen nun 5 elcometer Thank you for your purchase of this Elcometer 195 Saberg Drill Welcome to Elcometer Elcometer are world leaders in the design manufacture and supply of inspection equipment for coatings and concrete Our products cover all aspects of coating inspection from development through application to post application inspection The Elcometer 195 Saberg Drill is a world beating product With the purchase of this product you now have access to the worldwide service and support network of Elcometer For more information visit our website at www elcometer c
3. ecess socket head screw Place the drill body on the surface to be measured with the hole directly above the test area Fit the cutter into the drill hole Rotate the handwheel in a clockwise direction using pressure as necessary for soft coatings rotate finger in recess until the cutter has penetrated the coating and marked the substrate Remove cutter assembly and the drill body View the hole with the microscope focusing on the side of the hole Note the number of graticule divisions between the coating surface and the colour change between the coating and substrate or next paint surface To calculate the coating thickness multiply the number of graticule divisions by 20 to give the coating thickness in microns or multiply the number of graticule divisions by 0 79 to give the coating thickness in mils These instructions are valid for a 20 um division microscope elcometer 3 MAINTENANCE The Elcometer 195 Saberg Drill is designed to give many years service under normal operating and storage conditions The instrument does not contain any user serviceable components In the unlikely event of a fault the instrument should be returned to your local Elcometer supplier or directly to Elcometer Contact details can be found on the outside cover of these instructions or on the Elcometer website www elcometer com 4 SPARE PARTS The following spare part is available from Elcometer or your local supplier Spare 90 drill T19
4. om 1 ABOUT YOUR DRILL The Elcometer 195 Saberg Drill provides a method of assessing coating thickness layers especially on hard or brittle coatings For some coating substrate combinations it is necessary to use a destructive method Whereas a Paint Inspection Gauge P I G makes a linear cut along the coating the Elcometer 195 S berg Drill makes a small hole in order to measure the coating thickness layer thus much less damage is done e Ideal for hard or brittle coatings Measures coatings up to 1500um 60mils e Used in conjunction with a graticule scale microscope included 1 1 WHAT THE BOX CONTAINS e Heavy handwheel e Light handwheel e Cutter e Hexagonal wrench Drill body e Microscope e Carrying Case e Operating Instructions The instrument is packed in a cardboard and foam package Please ensure that this packaging is disposed of in an environmentally sensitive manner Consult your local Environmental Authority for further guidance To maximise the benefits of your new instrument please take some time to read these Operating Instructions Do not hesitate to contact Elcometer or your Elcometer supplier if you have any questions elcometer elcomeler 2 USING YOUR DRILL 1 Select appropriate handwheel heavy for use on hard or thick coatings ie above 250 microns or e light for soft or thin coatings ie below 250 microns Fix the cutter on the handwheel selected Tighten the r
Download Pdf Manuals
Related Search