Medical Monitor Arms Assembly and Operating Instructions
Contents
1. H i Bi tnstructions ErgenoFlex l rofessional edical Monitor Mounting Assembly and Operating Instructions i f I i I erating Instructions lush Mount Assembly and Operating Instructions a ae m _ Ss Workplace Wellnes Part Number EGF 91110 EGF 91115 EGF 91120 www ergonoflex com Er Assembly and Operating Instructions Flush Mount EGF 91110 EGF 91115 EGF 91120 oF lex General Notes 1 Verify that the support to which the arm is to be mounted has been properly installed 2 Check the weight of the device to be mounted This arm is rated for 18 kg holding a 3 Please read all warnings marked with carefully For any questions please contact ErgonoFlex 4 fold safety factor Scope of Delivery 1 support arm 2 locating pins 1 adapter plate VESA 75 100 1 locking lever to lock the monitor tilt head 1 set screws VESA 1 hex key 4 mm Assembly Steps 1 Mount the adapter for the wall channel the European rail adapter or the pole adapter using the screws M 8 x 25 M 8 x 30 orM 8 x 40 Please note The screws to mount the adapter are self tapping screws In order to make it easier to fix the screws the threads are already tapped Should you have difficulties in fastening the screws Please make sure that you strongly tighten the screws 2 Slide the support arm into the wall channel and tighten the set screws With European rail2. Locating the Wall Channel Generally the bottom edge of the wall channel length 48 cm is placed 1 40 to 1 50 m above the floor The monitor device can be moved up and down within the wall channel by 38 cm Do not place any portion of the device over a patient bed A A Exclusion of Liability The proper installation is beyond ErgonoFlex med s control and lies in the responsibility of the hospital its consultant or contractor ErgonoFlex cannot be hold responsible for any damage which is due to improper installation Make sure that the installation is carried out by professio nal personnel only rating Instructions iii nt Mie NY EG F 91105 EGF 91106 EGI 01118 EGF 91119 EGF 91135 br 91127 F 91123 GF 91124 EGF 91137 EGF 91138 inf 91131 GF 91132 Nh Hy if E fi e asion Lift Variable sht Arm Assembly and erating Instructions pot Number ergonotlex com Er oFlex Assembly and Operating Instruction ErgonoFlex Medical Variable Height Arm 1 spiral cable wrap 3 cable clips 1 mounting set hex key 3 mm for wall channel adapter 4 mm 5 mm 6 mm M 6 x 40 hex screw Scope of Delivery Variable Height Arm with Extension Arm 1 Variable Height Arm with Extension Arm 3 end caps 1 aluminium profile for Variable Height Arm 1 aluminium profile for Extension Arm 1 spiral cable wrap 3 cable clips 1 mounting set hex key 3 mm f
3. yi B O Ad bit Ahh VW AI EGF 91103 EGF 91116 a EGF 91117 yl d i nN EGF 91133 l wh bT Ai 91125 EGF 91126 EGE 01121 if i al EGF 91121 EGF 91122 K f gt it H j l i J ting Instructions tension Arm Pivot sembly and Operating Instructions ergonoflex com Er ErgonoFlex Extension arm Pivot Assembly and Operating Instructions Pivot Arm oFlex A Assembly WARNING Never attempt to loosen the hex screws and the locking lever when the monitor is mounted to the arm Always remove the monitor first Cleaning ErgonoFlex support arms may be cleaned with mild non abrasive solutions commonly used in hospital environment Do not use steel wool or other abrasive material A warninc Never attempt to remove the support arm from the CIM wall channel when loaded with the device Exploded View Rear Side View 1 support arm profile 2 aluminium profile 3 pivot point 4 pole adapter 5 plastic covers for cast parts 6 end cap for pivot point 7 end cap for front cast part 8 horizontal rail clamp 9 vertical rail clamp 10 side adapter ceiling pendent 11 rail adapter with levelling feet 1a 1 I Operating Instructions c P oFlex LT Hi EARL on Dual Arm Pivot Assembly and Operating Instructions Dual Articulating Arm Assembly and Operating General Notes Instructions AY 1 Verify that the wall channel has been
4. Workplace Wellness 5 Only after set screws have been tightened can medical devices be mounted For most devices a specific adapter plate provided by ErgonoFlex med is needed Please refer to assembly instru tions provided with the adapter plate 6 Once the adapter plate has been attached to the device secure it to the mounting plate of the www ergonoflex com support arm Slide the device into the mounting plate until plunger locates in the clearance hole Tighten the nylon screws in the mounting plate With VESA adaptations the flat panel is attached directly to the VESA mounting plate at the front of the support arm Please use the M 4 screws with the suitable length If needed nylon spacers can be used iting Instructions ii Er i sion Dual Arm Pivot Assembly and Operating Instructions Dual Articulating Arm oF lex Let q bly and Operating i structions Tilt Swivel and Pivot Adjustments lien To adjust the overall tilt tension tighten or loosen the 2 hex screws with the hex key 4 mm pro 4 umber vided To adjust the swivel and or pivot tension remove the blue end caps and tighten or loosen the 4 head screws Tilt Adjustment Swivel Pivot Adjustment PEA WARNING Or 91122 Never attempt to loosen the hex screws and the locking lever when the monitor is Do mounted to the arm Always remove the monitor first EGF 91129 Cleaning a IF ErgonoFlex support arms may be cleaned with mild no
5. Assembly and g Instructions Number F 91113 F 91114 1101 i 91102 01104 H 91105 F 91106 Er 5 Slide the arm into the wall channel or mount it to the European rail or the pole 6 Remove the inner cover from the inner pivot block by loosing the 2 M 5 x 20 screws 7 Disengage the locking lever and bring the arm in position may the inner cover be removed 8 Remove the right hex screw M 6 x 12 and replace it with the hex key M 6 x 40 Fasten the screw until the depth gauge without using any force The M 6 x 40 screw is used to punch the spindle through with a hammer by about 20 mm Then unscrew the M 6 x 40 screw rating Instructions Er oFlex f ma ion Lift Variable A WARNING Avoid pulling out the spindle completely Arm Assembly and ating Instructions on g art fe Number EGF 91101 Wer 91102 IGF 91104 E 6 F 91105 it EGF 1106 9 Lead the spiral cable wrap with the cables from below through the console and from above IP through the inner pivot block into the support arm profile F SF pie Lead the spiral cable warp from the support arm profile downwards through the outer pivot block EGF 91119 10 Re assemble the support arm in reversed order D EG rl 91135 Medical Variable Height Arm with Extension Arm ZG 3F 91127 1 De EF 112 Proceed in the way as described with the Variable Height Arm step 1 to step 8 Please make sure Z it 9 3 that you exactly follow the moun
6. M 8x40 Please note The screws to mount the adapter are self tapping screws In order to make it easier to fix the screws the threads are already tapped Should you have difficulties in fastening the screws Please make sure that you strongly tighten the screws 3 Slide the support arm into the wall channel and tighten the set screws With European rail mounts hook in the rail plate and make sure that the spring locked connecting pins snap in beneath the rail 4 Only after set screws have been tightened can medical devices be mounted For most devices a specific adapter plate provided by ErgonoFlex med is needed Please refer to assembly instructions provided with the adapter plate 5 Once the adapter plate has been attached to the device secure it to the mounting plate of the support arm Slide the device into the mounting plate until plunger locates in the clearance hole Tighten the nylon screws in the mounting plate With VESA adaptations the flat panel is attached directly to the VESA mounting plate at the front of the support arm Please use the M 4 screws with the suitable length If needed nylon spacers can be used Tilt Swivel and Pivot Adjustments To adjust the overall tilt tension tighten or loosen the 2 hex screws with the hex key 4 mm provided To adjust the swivel and or pivot tension remove the blue end caps and tighten or loosen the 4 head screws Tilt Adjustment Swivel Pivot Adjustment Lia Mh
7. channel the European rail adapter or the pole adapter using the screws M 8 x 25 M8 x 30 or M 8x40 Please note The screws to mount the adapter are self tapping screws In order to make it easier to fix the screws the threads are already tapped Should you have difficulties in fastening the screws please make sure that you strongly tighten the screws 3 Mount the front and rear support arm components after having placed the cables Please place the plastic layer ring first before assembling the two support arm components Then place the plastic ring and the metal ring and screw the two support arm components together by using the 4 M 5 x 16 self tapping screws A Electric Safety To comply with the regulations for electric safety in medical environments International Standards IEC an additional equipotential bonding connector is provided In order to eliminate any difference in potential between touchable parts ground and other conductive parts and to protect people from electric shock make sure that the support arm is connected to the potential bonding Furthermore consider the national electric safety regulations Mounting the Monitor 1 Ensure that the locking lever is engaged with the arm in the highest vertical posi tion Do not disengage the locking lever unless an instrument is mounted on the end of the support arm 2 Slide the support arm into the wall channel and tighten the set screws With European rail mounts hook in
8. installed and approved according to the Channel yi Part Number installation instructions If you want to attach the arm to an existing European rail please verify EGF 91111 that the rail can hold the weight EGF 91112 2 Check the weight of the device to be mounted This arm is rated for 10 kg holding a 6 fold safety factor EGF 91100 A EGF 91103 3 Cable integration and assembly may only be done by qualified personnel ErgonoFlex med cannot be hold responsible for any damage due to insufficient 441 EGE 91116 assembly EGF 91117 4 Please read all warnings marked with carefully EGF 91133 For any questions please contact ErgonoFlex or your local dealer Scope of Delivery EGF 91125 1 assembled support arm EGF 91126 3 hex keys 3 mm for adapter wall channel 4 mm to adjust tilt mechanism of the monitor adaptation 6 mm EGF 91121 for M 8 hex screws or bit for M 8 countersink screws EGF 91121 Cable Integration The cable channel organizes 3 4 cables depending on the cable diameter EGF 91122 EGF O11 26 Assembly Steps 1 To integrate the cables the pivot point s opening must be turned to be over the aluminium EGF 01129 profile Now place the cables wrapped in the spiral cable wrap in the aluminium profile and the EGF cast parts Slide the 2 plastic covers in the cast parts and clip the aluminium profile into the 91130 upper support arm profile and attach the end caps Please make sure that the end cap
9. with the cable pass thru is attached to the front cast part refer to illustration position cable integr tion In case your support arm has no completely integrated cable management your cables can be lead along the support arm profiles Please remove the lower support arm profile by using a screw driver Put the screw driver to the notch provided for this purpose Please note that you require a lower support arm profile with cable pass thru which can be order with ErgonoFlex med part no 65 AL DR Please indicate the length of your support arm 2 Mount the adapter for the wall channel the European rail adapter or the pole adapter using the screws M 8 x 25 M 8x 30 or M 8x40 Please note The screws to mount the adapter are self tapping screws In order to make it easier to fix the screws the threads are already tapped Should you have difficulties in fastening the screws Please make sure that you strongly tighten the screws 3 Mount the front and rear support arm components after having placed the cables Please place the plastic layer ring first before assembling the two support arm components Then place the plastic ring and the metal ring and screw the two support arm components together by using the 4 M 5 x 16 self tapping screws 4 Slide the support arm into the wall channel and tighten the set screws With European rail mounts hook in the rail plate and make sure that the spring locked connecting pins snap in beneath the rail
10. EGEF 91124 6 Lead the spiral cable wrap with the cables through the Variable Height Arm and follow the ins EGF 911 tructions described in step 9 Variable Height Arm 91157 7 Put the spindle back to its position Follow the instructions described in step 8 Variable EGF O11 38 Height Arm but in reversed order EGF 91131 8 Mount the inner cover to the inner pivot block using 2 M 5 x 20 hex screws Follow the EGF 91132 instructions described in step 6 and 7 Variable Height Arm but in reversed order 9 Mount the Extension Arm to the Variable Height Arm using the components in reversed order YV 10 Mount the adapter for the wall channel the European rail adapter or the pole mount to the Y console Please make sure that you do not forget the 2 locating pins eB 11 Slide the support arm into the wall channel or mount it to the European rail or pole it Disengage the locking lever and put the arm in the highest position 177 12 Mount the outer cover to the outer pivot block using 2 M 5 x 20 hex screws Follow the instructions described 1n ste arlable Height Arm ions described 1 p 4 Variable Height A 13 Mount the monitor adaptation to the support arm Follow the instructions described in step 3 Variable Height Arm but in reversed order OD Q ae O www ergonoflex com OF lex a T M Instructions Er ix te Meion Lift Variable el igh t Arm Assembly and ok Instructions Electric Safety To comply with the regul
11. ations for electric safety in medical environments International F WA Number VEGF 91113 EGF 91114 EGF 91101 _ EGF 91102 7 he 91104 NEGF 91105 AW IGF 91106 EN IGF 91118 EGF 91119 EGF 91135 _ EGF 91127 EGF 91123 EGF 91124 EGF 91137 i _ EGF 91138 EGF 91131 H ill 91132 W Standards IEC an additional equipotential bonding connector is provided In order to eliminate any difference in potential between touchable parts ground and other conduc tive parts and to protect people from electric shock make sure that the support arm is connected to the potential bonding Furthermore consider the national electric safety regulations Mounting the Monitor 1 Ensure that the locking lever is engaged with the arm in the highest vertical position Do not disengage the locking lever unless an instrument is mounted on the end of the support arm 2 Slide the support arm into the ErgonoFlex wall channel or mount it to the European rail or pole and tighten the set screws 3 Only after set screws have been tightened can medical devices be mounted For most devices a specific adapter plate provided by ErgonoFlex med is needed Please refer to assembly instructions provided with the adapter plate 4 Once the adapter plate has been attached to the device secure it to the mounting plate of the support arm Slide the device into the mounting plate until plunger locates in the clearance hole Tighten the nylon screws in t
12. ce Wellness www ergonoflex com un if F 91113 AGF 91114 GF 91101 IGF 91102 JF 91104 GF 91106 3G 4 91118 l I i Ke 1 1 1 9 TAT EGI iy GF 91138 iis ieee EGF 91132 T ii N Ann gt Fe l gt i B I iM W i ating Instructions nsion Lift Variable t Arm Assembly and ating Instructions t Number T80 10flex com oF lex 1 Tragarmprofil 2 aluminium profile for extension 3 pivot point 4 adapter for wall channel European Rail and pole 5 plastic covers for cast 6 end cap for pivot point 7 end cap for front cast part 8 aluminium profile for Variable 9 plastic ring 10 metal ring 11 plastic layer ring
13. he mounting plate With VESA adaptations the flat panel is attached directly to the VESA mounting plate at the front of the support arm Please use the M 4 screws with the suitable length If needed nylon spacers can be used Tilt Swivel and Pivot Adjustments To adjust the overall tilt tension tighten or loosen the 2 hex screws with the hex key 4 mm provided To adjust the swivel and or pivot tension remove the end caps and tighten or loosen the 4 head screws WARNING For devices mounted from the bottom the tilt angle is limited to 20 Never attempt to loosen the hex screws and the locking lever when the monitor is mounted to the arm Always remove the monitor first Cleaning ErgonoFlex support arms may be cleaned with mild non abrasive solutions commonly used in hospital environment Do not use steel wool or other abrasive material Operating Instructions c P oFlex RE M Extension Lift Variable Height Arm Assembly and Operating Instructions WARNING 1 Never attempt to remove the support arm from the ErgonoFlex wall channel when loaded with Part Number the device EGF 91113 When removing the instrument please verify that the locking lever is engaged with the arm in the highest vertical position EGF 91114 1 EGF 91101 Wall Mount Overview EGF 91102 EGF 91104 1 EGF 91105 EGF 91106 EGF 91118 EGF 91119 EGF 91135 EGF 91127 EGF 91123 EGF 91124 EGF 91137 EGF 91138 EGF 91131 EGF 91132 Workpla
14. ith the Arm in the highest vertical position and with the height locking lever engaged Failure to follow these guidelines could result in serious injury General Notes 1 Verify that the wall channel has been installed and approved according to the channel installation instructions If you want to attach the arm to an existing European rail please verify that the rail can hold the weight 2 Check the weight of the device to be mounted This arm is rated for 15 kg holding a 6 fold safety factor 3 Cable integration and assembly may only be done by qualified personnel ErgonoFlex med cannot be hold responsible for any damage due to insufficient assembly 4 Please read all warnings marked with carefully A For any questions please contact ErgonoFlex or your local dealer Scope of Delivery Variable Height Arm 1 Variable Height Arm 2 end caps 1 aluminium profile for ELVH Arm 1 adapter for wall channel European rail adapter or pole adapter including mounting material 1 spiral cable wrap Scope of Delivery Variable Height Arm with Extension Arm 1 Variable Height Arm 3 end caps 1 aluminium profile for VHM Arm 1 plastic ring 1 plastic layer ring 1 metal ring 4 M 5 x 16 self tapping screws 2 plastic covers for cast parts 1 aluminium profile for Extension Arm 1 adapter for wall channel European rail adapter or pole adapter including mounting material 3 hex keys 3 mm for adapter wall chan
15. mounts hook in the rail plate and make sure that the spring locked connecting pins snap in beneath the rail 3 Only after set screws have been tightened can medical devices be mounted For most devices a specific adapter plate provided by ErgonoFlex med is needed Please refer to assembly instruc tions provided with the adapter plate 4 Once the adapter plate has been attached to the device secure it to the mounting plate of the support arm Slide the device into the mounting plate until plunger locates in the clearance hole Tighten the nylon screws in the mounting plate With VESA adaptations the flat panel is atta ched directly to the VESA mounting plate at the front of the support arm Please use the M 4 screws with the suitable length If needed nylon spacers can be used Tilt Swivel and Pivot Adjustments To adjust the overall tilt tension tighten or loosen the 2 hex screws with the hex key 4 mm pro vided To adjust the swivel and or pivot tension remove the blue end caps and tighten or loosen the 4 head screws C C Tilt Adjustment Swivel Pivot Adjustment WARNING Never attempt to loosen the hex screws and the locking lever when the monitor is mounted to the arm Always remove the monitor first Cleaning ErgonoFlex support arms may be cleaned with mild non abrasive solutions commonly used in hospital environment Do not use steel wool or other abrasive material A WARNING Never attempt to remove the support arm fr
16. n abrasive solutions commonly used in a 91130 hospital environment Do not use steel wool or other abrasive material A WARNING i Never attempt to remove the support arm from the wall channel when loaded with the device Illustration Rear Side View gt _ Sy I iE t oi 1 support arm components l 2 aluminium profiles 3 pivot point J 4 adapter for wall channel European Rail and pole f 5 plastic covers for cast parts 6 end caps for middle and rear cast part 7 end cap for front cast part E VVUOL ee WA fos N N 7 E ie a nD m f gs I f osition Cable Integration La i I Operating Instructions LT bi tj 1 AN W i Part Number www ergonoflex com Extension Lift Variable Height Arm Assembly and Operating Instructions EGF 91113 EGF 91114 EGF 91101 EGF 91102 EGF 91104 EGF 91105 EGF 91106 EGF 91118 EGF 91119 EGF 91135 EGF 91127 EGF 91123 EGF 91124 EGF 91137 EGF 91138 EGF 91131 EGF 91132 Workplace Wellness Er Assembly and Operating Instruction ErgonoFlex Lift Variable Height Arm oFlex Please read this instruction carefully before installing the arm A Warning The ELVH Arm contains a strong spring which is used to counterbalance the weight of the mounted instrument The Arm housing should never be disassembled by non professional and untrained personnel Additionally the mounted instrument should only be removed w
17. nel 4 mm to adjust tilt mechanism of the monitor adaptation 6 mm for M 8 hex screws or bit for M 8 countersink screws 1 spiral cable wrap A Cable Integration Delivery contains a spiral cable wrap for cables The spiral cable wrap is to protect the cables against damage and squeezing especially in the pivot zones Please make sure that the spiral cable wrap goes through both joints Wrap the spiral cable wrap around the cables Make sure that the cables are not contorted The spiral cable wrap organizes up to cables depending on the cable diameter The spiral cable wrap may not exceed a diameter of 15 mm Cables may only be integrated when the spiral cable wrap is used Non observance may result in damaging the cables In case your support arm has no completely integrated cable management your cables can be lead along the support arm profiles Please remove the lower support arm profile by using a screw driver Put the screw driver to the notch provided for part no 65 AL ELVH Please indi cate the length of your support arm Cabling Please follow the steps as described below To run the cables through the ELVH Arm please make sure that the arm is in the highest verti cal position when possible To lead the cables through the joints the arm must be in a horizontal craned position with the locking lever engaged La i I Operating Instructions LT bi Extension Lift Variable Height Arm Assembly and Operating In
18. om the wall channel when loaded with the device ir EGF 91111 I EGF 91112 EGF 91100 EGF 91103 EGF 91116 I EGF 91117 MEGF 91133 EGF 91125 EGF 91126 EGF 91121 EGF 91121 EGF 91122 EGF 91136 EGF 91129 EGF 91130 Workplace Wellness i www ergonoflex com Er ErgonoFlex Extension arm Pivot Assembly and Operating Instructions Extension Pivot Arm Assembly Steps oF lex 1 To integrate the cables wrapped in the spiral cable wrap the pivot point s opening must be turned to be over the aluminium profile Now place the cables in the aluminium profile and the cast parts Slide the 2 plastic covers in the cast parts and clip the aluminium profile into the upper support arm profile and attach the end caps Please make sure that the end cap with the cable pass thru is attached to the front cast part Refer to illustration position cable integration In case your support arm has no completely integrated cable management your cables can be lead along the support arm profiles Please remove the lower support arm profile by using a screw driver Put the screw driver to the notch provided for this purpose Please note that you require a lower support arm profile with cable pass thru which can be order with ErgonoFlex med part no 65 AL PV Please indicate the length of your support arm 2 Mount the adapter for the wall channel the European rail adapter or the pole adapter using the screws M 8 x 25 M 8x 30 or
19. or wall channel adapter 4 mm 5 mm 6 mm M 6 x 40 hex screw A Cable Integration Delivery contains a spiral cable wrap for cables The spiral cable wrap is to protect the cables against damage and squeezing especially in the pivot zones Please make sure that the spiral cable wrap goes through both joints Wrap the spiral cable wrap around the cables Make sure that the cables are not contorted The spiral cable wrap organizes up to 3 cables depending on the cable diameter The spiral cable wrap may not exceed a diameter of 15 mm Cables may only be inte grated when the spiral cable wrap is used Non observance may result in damaging the cables In case you do not wish completely integrated cable management 3 cable clips help manage cables Fix the cable clips underneath the aluminium profile A cabtine Please follow the steps as described below Medical Variable Height Arm 1 Remove the end caps if not removed already 2 Remove the aluminium profile form the Variable Height Arm if not removed already 3 Remove the monitor adaptation by loosing the 4 M 5 x 16 screws You have the following components now plastic layer ring plastic ring metal ring 4 M 5 x 16 screws Please make sure that you re assemble the monitor adaptation in the reversed order 4 Remove the outer cover form the outer pivot block by loosing the 2 socket head screws M 5 x 20 i 1 f ing Instructions on Lift Variable rm
20. structions k i Part Number EGF 91113 my EGF 91114 ian EGF 91101 EGF 91102 EGF 91104 EGF 91105 EGF 91106 EGF 91118 EGF 91119 EGF 91135 EGF 91127 EGF 91123 EGF 91124 EGF 91137 EGF 91138 EGF 91131 EGF 91132 Workplace Wellness www ergonoflex com Er Assembly and Operating Instruction ErgonoFlex Lift Variable Height Arm oFlex Please be careful not to disengage the locking lever while handling the arm A Variable Height Arm 1 Remove the end caps if no removed already 2 Remove the aluminium profile form the ELVH arm if not removed already 3 Remove the inner cover from the inner pivot block by loosing the 2 socket head screws M 5 X 20 4 Remove the outer cover form the outer pivot block by loosing the 2 socket head screws M 5 X 20 5 In order to run the cables through the VHM arm the arm must be in a horizontal craned position When handling the arm please make sure that you do not disengage the locking lever Extension Arm 1 To integrate the cables the pivot point s opening must be turned to be over the aluminium profile Now place the cables wrapped in the spiral cord wrap in the aluminium profile and the cast parts Slide the 2 plastic covers in the cast parts and clip the aluminium profile into the upper support arm profile and attach the end caps Please make sure that the end cap with the cable pass thru is attached to the front cast part 2 Mount the adapter for the wall
21. the 2 hex screws with the hex key 4 mm pro vided To adjust the swivel and or pivot tension remove the blue end caps and tighten or loosen the 4 head screws Tilt Adjustment Swivel Pivot Adjustment Never attempt to loosen the hex screws and the locking lever when the monitor is mounted to the arm Always remove the monitor first Cleaning ErgonoFlex support arms may be cleaned with mild non abrasive solutions commonly used in hospital environment Do not use steel wool or other abrasive material A warninc Never attempt to remove the support arm from the wall channel when loaded with the device When removing the instrument please verify that the locking lever is engaged with the arm in the highest vertical position Exploded View Rear Side View 1 Tragarmprofil 2 aluminium profile for extension 3 pivot point 4 adapter for wall channel European Rail and pole 5 plastic covers for cast 6 end cap for pivot point 7 end cap for front cast part 8 aluminium profile for Variable 9 plastic ring 10 metal ring 11 plastic layer ring 1a 1 I Operating Instructions LT gi Wall Channel Assembly 1 y and Operating Instructions Workplace Wellness Part Number EGF 91139 EGF 91140 EGF 91141 EGF 91142 www ergonoflex com Er oFlex Assembly Instruction Wall Channel General Notes It shall be the responsibility of the hospital its consultants or contractors to determine that
22. the wall channel is suitable to safely and securely mount the monitor device This includes the selection of the suitable fasteners and the proper installation of the same In new construction and remodelling work where the wall covering can be entirely or partly removed a 16 gauge steel stud should be located for the purpose of attaching the wall channel The following information is to provide guideline information only For any questions please contact ErgonoFlex or your local dealer Mounting Material Mounting material is not included in the scope of delivery It is important to check the load capacity of the wall and to make sure that the adequate and recommended mounting material is used Please consult your technical department Drywall The wall channel must be anchored into the studs Make sure that the appropriate fasteners and mounting material is used and the manufacturers instructions for proper installation are adhe red to Make sure that the studs are safe to mount the wall channel Concrete Wall Make sure that the appropriate fasteners and mounting material is used and the manufacturers instructions for proper installation are adhered to Refer to qualified personnel Metal Sheet or Wooden Wall Make sure that the appropriate fasteners and mounting material is used and the manufacturers instructions for proper installation are adhered to Make sure that the metal sheet or wooden wall is safe to mount the wall channel
23. the rail plate and tighten the set screws 3 Only after set screws have been tightened can medical devices be mounted For most devices a specific adapter plate provided by ErgonoFlex med is needed Please refer to assembly instructions provided with the adapter plate 4 Once the adapter plate has been attached to the device secure it to the mounting plate of the support arm Slide the device into the mounting plate until plunger locates in the clearance hole Tighten the nylon screws in the mounting plate With VESA adaptations the flat panel is attached directly to the VESA mounting plate at the front of the support arm Please use the M 4 screws with the suitable length If needed nylon spacers can be used TT WW srating Instructions Wi al 1 i e i ension Lift Variable 3 ght Arm Assembly and berating Instructions y TE Part Number HY EG F 91105 Ny GF 91106 EGE 91119 EGF 91135 Ber 91127 SF 91123 f EC SF 91124 E EGF 91137 I EGF 91138 i 91131 iil 91132 p gt rr a rr ya JANI Or go oal S be Ne io war fi sD BE ry K had fn _ Dda a z AN 7 Ve n v U lt lt ae rgonoflex com _ Og h i Er Assembly and Operating Instruction ErgonoFlex Lift Variable Height Arm oFlex Tilt Swivel and Pivot Adjustments To adjust the overall tilt tension tighten or loosen
24. ting instructions and warnings Then proceed in the way as des rig H 3F 91124 cribed below I E F 91137 1 Remove the support arm from the wall channel the European rail plate or the pole mount Please make sure the support arm is in the lowest position and be careful not to disengage the F iC IGF 91138 locking lever by chance GI 901131 2 Remove the adapter for the wall channel the European rail plate or the pole mount from the 91132 console and turn it by 180 cr Please make sure that you do not forget the 2 locating pins when re assembling the adapter 3 Remove the end caps and the aluminium profile if not removed already 4 Depending on the connector type it may be necessary to disassemble the Extension Arm from the Variable Height Arm by loosing the 4 M 5 x 20 screws You have the following components now Variable Height Arm plastic layer ring extension arm f plastic ring metal ring 4 M 5 x 20 screws Please make sure that you re assemble the arm in reversed order i Operating Instructions Er i i A Extension Lift Variable Height Arm Assembly and Operating Instructions Part Number EGF 91113 Vi EGF 91114 Wn EGF 91101 EGF 91102 ARAN 1 EGF 91104 kT 1 5 Put the spiral cable wrap into the support arm profile and turn the console back by 180 to its j EGF 91105 original position EGF 91106 EGF 91118 EGF 91119 EGF 91135 EGF 91127 EGF 91123
Download Pdf Manuals
Related Search