User manual of ZWG3 controller
Contents
1. network is possible only via PRIMARY controller every single brand new controller is set as primary controller by default In each network there is always only one primary controller and any other added to it is identified as SECONDARY The procedure of device adding to the network is presented in Figure 2 1 Press In Ex button once 2 The controller is signalizing its readiness 3 Press P button on the device for adding a new device to the network and hold it for 0 5 sec see button lights up for 10 sec as presented in Installation Manual the drawing 4 The controller is signalizing that the 5 Programming error button flashing for device has been successfully added to 2 3 sec as presented in the drawing the network button lights up for 2 3 sec as presented in the drawing Note In the newer controller version interrupting any procedure is possible by pressing the IN EX button In the older version it is necessary to wait 10 seconds until the error is signalled by the controller or reset it by removing the batteries Figure 2 Adding device to Z Wave network Programming error can be caused by no button being pressed within 10 seconds from controller signaling its readiness for adding a new device to the network e long distance between controller and device being added e the device already belonging to other network It is necessary to us2. of DEFAULT function 4 Technical parameters Technical parameters CR2450 3V DC 5 C to 40 C Up to 40 m 868 42 MHz Power supply Working temperature Working range Working frequency 2012 FAKRO 11 11 15 NC826 10 16 5 Battery replacement With standard controller use four times a day the battery should theoretically ensure correct device functioning for the period of 2 years assuming that the programming procedure has been performed only once Multiple device programming shortens the battery life 1 Remove the keyboard from the wall holder 2 Take the battery out by pulling on the tape Che i 3 Put the battery into position paying attention to the correct polarisation Position the tape for removing the battery in a way enabling sliding the battery out again with the use of this tape 11 11 15 NC826 11 16 2012 FAKRO 6 WARRANTY The manufacturer guarantees correct device functioning It also undertakes to repair or replace the device if its defects result from material or structural faults The warranty period is 24 months from the purchase date fulfilling the following conditions Installation has been performed by an authorised individual as per manufacturer recommendations Seals remain intact and no unauthorised st
3. FAKRO 3 4 Deleting device from a pair of controller buttons DELETE function This function deletes from controller s memory the device associated with a pair of buttons on a selected channel However it does not remove the device form the Z Wave network This function is accessible from PRIMARY and SECONDARY controllers The procedure of device deleting from a pair of controller buttons is presented in Figure 6 1 Within 1 5 sec press 2 The controller is signalising 3 Press P button on the device In Ex 1 button twice and then readiness for device deleting button and hold it for 0 5 sec see Device the button from this pair of buttons lights up for 10 sec as presented in Programming Manual which operates the device to be the drawing removed e g 2 4 The controller is signalizmg 5 Programming error button successful device deleting buttons flashing for 2 3 sec as presented in lights up for 2 3 sec as presented the drawing in the drawing Note In the newer controller version interrupting any procedure is possible by pressing the IN EX button In the older version it is necessary to wait 10 seconds until the error is signalled by the controller or reset it by removing the batteries Figure 5 Deleting device from a pair of buttons on the controllers Programming error can be caused by failure to press the programming button
4. FAKRO User manual of ZWG3 controller Contents LES CP a a e AE KRONE OAK CAE RER AUE BEA 2 2 Installation of ZWG3 controller oO PRO O A W O O AAA oem neues 3 CUnGoler POST AMEN i ok alko i AO ORA e WRO 4 3 1 Adding device to network INCLUDE function aoc o ooo 5 3 2 Associating device with a pair of buttons on the controller ASSOCIATE function 6 3 3 Associating another controller with the network LEARN MODE 7 3 4 Deleting device from a pair of controller buttons DELETE function pp 8 3 5 Excluding device from the network EX CLUDE function paz AO AG A 9 3 6 Restoring default settings in the controller DEFAULT function 10 3 7 Removing SECONDARY controller from the network MRR R 10 4 Technical parameters we A ser tas WG nue tete Gare Eee ea Re MN dE 10 Balety replacements cekiny O uae snake tals eee tte car ler on ee 11 6 WARRANTY wa O e AA O R EA b GOA ROA AE 12 11 11 15 NC826 1 16 2012 FAKRO 1 Description The ZWG3 wall keyboard enables remote control of electronic accessories compatible with the Z Wave system e g ZWS12 or ZWS30 motors for operating FAKRO roof windows The ZWG3 controller can operate up to 3 devices separately The ZWG3 controller is equipped with a two way Z Wave communication radio module For communication the Z Wave module exploits radio wave frequency of 868 42 MHz In Figure I there is presen
5. cluded a maximum of 232 devices i e controllers electronic accessories for FAKRO roof windows as well as other electronic devices Note Any device which is physically removed from the network e g damaged should be deleted from the memory of the controller PRIMARY SECONDARY that is first deleted from the pair of buttons section 3 4 and then removed from the network section 3 5 The correct implementation of the procedures is to ensure optimal communication between devices Unplugging the device without removing it from the controller memory will result in a prolonged reaction time to commands and faster depletion of the controller battery If it is necessary to remove the damaged equipment whose removal from the controller memory is not possible it is desirable to reconfigure the whole network all devices Start a new network configuration from restoring the controller to the factory settings DEFAULT function then call the EXCLUDE function of devices working correctly and continue to the section 3 Controller Programming Note Moving the device within the network e g socket module it is recommended to delete it from the controller memory delete it from the pair of buttons first section 3 4 and then remove from the network section 3 5 and then add it again after installation in new place of work 11 11 15 NC826 4 16 2012 FAKRO 3 1 Adding device to network INCLUDE function Adding a device to the Z Wave
6. e EXCLUDE function and repeat the procedure of device adding to the network 11 11 15 NC826 5 16 2012 FAKRO 3 2 Associating device with a pair of buttons on the controller ASSOCTATE function Associating the device with a pair on buttons on the controller which has been already included in the Z Wave network according to section 2 1 makes it possible to operate the device This procedure can be carried out on the primary and secondary controllers The procedure of associating the device with buttons is presented in Figure 3 1 Within 1 sec press 2 The controller is signilizing 3 Press P button on the device and In Ex 1 button once and then readiness for associating the hold it for 0 5 sec see Device the button from this pair pfbuttons device with a pair of buttons on Programming Manual which will operate the device e g 2 the controller buttons light up for 10 sec as presented in the drawing 4 The controller is signalizing that the 57 Programming error buttons device has been successfully associated flashing for 2 3 sec as presented in button light up for 2 3 sec as the drawing presented in the drawing Note In the newer controller version interrupting any procedure is possible by pressing the IN EX button In the older version it is necessary to wait 10 seconds until the error is signalled by the controller
7. ontroller is signalling PRIMARY controller see 3 1 LEARN MODE which is to be added assigning with the network to the network three times within 1 5 sec buttons light up for 10 sec as presented in the drawing Secondary Primary _ Secondary 4 After few seconds the controller is signalizing that associating with the 5 Programming error network has been successfully completed buttons light up for 2 3 sec as buttons flashing for 2 3 sec as presented in the drawing presented in the drawing Note To control the devices form the controller Secondary perform the ASSOCIATE function see section 3 2 Note In the newer controller version interrupting any procedure is possible by pressing the IN EX button In the older version it is necessary to wait 10 seconds until the error is signalled by the controller or reset it by removing the batteries Figure 4 Associating another controller to Z Wave network Programming error can be caused by e failure to enter LEARN MODE on the controller being associated with the network within 10 seconds from primary controller signaling its readiness for adding a new device to the network e long distance between the primary controller and controller being added e controller already belonging to another network It is necessary to perform DEFAULT procedure with it and repeat associating with the network 11 11 15 NC826 7 16 2012
8. or reset it by removing the batteries Figure 3 Device associating with selected pair of buttons on controller Programming error can be caused by no button being pressed within 10 seconds from the controller signaling its readiness for associating a new device with the network long distance between the controller and device being added device already belongs to another network or it has not been associated with any network It is necessary to perform EXCLUDE function on the device and repeat INCLUDE and ASSOCIATE functions 11 11 15 NC826 6 16 2012 FAKRO 3 3 Associating another controller with the network LEARN MODE Associating further controllers with the network makes them being categorized as SECONDARY Associating a controller with the Z Wave network consists in sending data to it from the PRIMARY controller The procedure of controller associating is presented in Figure 4 In order to assure the best possible communication within the network and after each its modification including or removing a device associating another controller with the network should be performed after associating all devices with the first controller PRIMARY or performing LEARN MODE again on the SECONDARY controller already associated with the network Secondary 1 Press In Ex button once on the 2 Press In Ex button on the controller 3 The c
9. rogramming error may be caused by e failure to press the programming button within 10 seconds from the controller signaling its readiness for excluding the device from the network long distance between the controller and device being excluded 11 11 15 NC826 9 16 2012 FAKRO 3 6 Restoring default settings in the controller DEFAULT function Restoring default settings of the controller leads to the following information being deleted from its memory e network to which SECONDARY controller has been added e devices in the network for PRIMARY controllers e devices associated with pairs of buttons for PRIMARY and SECONDARY controllers After performing DEFAULT procedure the SECONDARY controller will be set as PRIMARY 1 Within 1 5 sec press 2 The controller is signalizing restoring default In Ex button twice 1 and then settings buttons flashing for 2 3 sec as FK button 2 once presented in the drawing Note In the newer controller version interrupting any procedure is possible by pressing the IN EX button In the older version it is necessary to wait 10 seconds until the error is signalled by the controller or reset it by removing the batteries Figure 7 Restoring default settings in controller 3 7 Removing SECONDARY controller from the network Removing this controller from the network consists in restoring default settings with the use
10. ructural changes have been made The device has been used in accordance with its intended use as per user manual Damage is not a result of improperly made electrical system or atmospheric phenomena The manufacturer is not liable for damage which occurred as a result of improper use or mechanical damage In case of failure the device must be submitted for repair with a Warranty Card Defects revealed within the warranty period will be removed free of charge no longer than 14 days after accepting the product for repair Warranty and post warranty repairs are performed by the manufacturer i e FAKRO PP Sp z 0 0 Quality Certificate Device Signature stamp of installing person 11 11 15 NC826 12 16 2012 FAKRO 11 11 15 NC826 13 16 2012 FAKRO 11 11 15 NC826 14 16 2012 FAKRO 11 11 15 NC826 15 16 2012 FAKRO FAKRO PP Sp z o o ul W gierska 144A 33 300 Nowy S cz Polska www fakro com tel 48 18 444 0 444 fax 48 18 444 0 333 11 11 15 NC826 16 16 2012 FAKRO
11. ted a general view of the ZWG3 keyboard with description of available buttons and signaling 1 Functional button In Ex 2 Functional button FK 3 Controlling buttons pair No l m 4 Controlling buttons pair No Il 5 Controlling buttons pair No III Dimension ZWG3 A 80 mm B 80 mm C 15 mm Figure 1 ZWG3 keyboard 11 11 15 NC826 2 16 2012 FAKRO 2 Installation of ZWG3 controller The ZWG3 controller should be attached to the wall or other permanent building element by means of four screws driven into cylindrical plugs placed in the openings drilled earlier in the wall Mounting bracket is also designed for mounting in a standard electric can 1 Fix the holder to the wall using included screws driven into wall plugs placed in the drilled openings 2 Place the ZWG3 controller onto the holder 11 11 15 NC826 3 16 2012 FAKRO 3 Controller programming In order to operate FAKRO electronic accessories featuring Z Wave system by means of the ZWG3 controller it is necessary to 1 Add the device to the Z Wave network INCLUDE function see section 3 1 and 2 Associate the device with a selected pair of buttons on the controller with which user wishes to operate the device ASSOCIATE function see section 3 2 In one Z Wave network there can be in
12. within 10 seconds from the controller signaling its readiness for deleting the device from selected pair of buttons long distance between the controller and device 11 11 15 NC826 8 16 2012 FAKRO 3 5 Excluding device from the network EXCLUDE function Excluding the device from the Z Wave network is possible only with the use of PRIMARY controller e g ZWK15 keyboard In each network there is always only one primary controller and every other is categorized as SECONDARY The procedure of device excluding from the network is presented in Figure 6 1 Press In Ex button twice 2 The controller is signalizing its readiness 3 Press P button on the device within 1 sec for excluding the device from the network and hold it for 0 5 sec see Device button lights up for 10 sec as presented in Programming Manual the drawing 4 The controller is signalizmg that the 5 Programming error button device has been excluded successfully flashing for 2 3 sec as presented button lights up for 2 3 sec as in the drawing presented in the drawing Note In the newer controller version interrupting any procedure is possible by pressing the IN EX button In the older version it is necessary to wait 10 seconds until the error is signalled by the controller or reset it by removing the batteries Figure 6 Excluding device from Z Wave network P
Download Pdf Manuals
Related Search