CASHFLOW 111 ACCEPTOR USER GUIDE
Contents
1. MEI 2000 CashFlow 111 User Guide SAFETY Warning Before cleaning servicing removing or replacing CashFlow units ALWAYS SWITCH OFF or ISOLATE the ELECTRICITY SUPPLY to the host machine Caution This guide is recommended for use by personnel trained to carry out electrical installation Maximum Operating Voltage Do not apply more than the voltage specified on the unit and within the following Full Operating Voltage range 12V DC nominal 43V 2V Supply Voltage Ripple Within Vmin to Vmax up to 100Hz lt 250mV pk pk for Frequency 100Hz Current consumption Quiescent current 35mA Max Max current 800mA Max Dangerous Environments Do not operate the unit in the presence of flammable gasses or fumes or after the entry of fluid into the machine Disposal of Product If necessary always dispose of defective units according to local regulations Conformance to International Standards When installed and operated according to the instructions provided for the particular unit CashFlow products meet the applicable international and national safety standards for any country in which they are used SAFETY All electrical connections to the product must be rated according to the requirements for Accessible SELV circuits as defined in EN60335 1 The product is therefore suitable for use in a class 2 non earthed or non grounded appliance Overcurrent protection is not included in the product and should be2. Reserved MEI 2000 21 Helping you deliver YOUR MEI REPRESENTATIVE
3. 3 Enable channel 0 as shown on page 12 Tr 7 sls N Switch validator power OFF N De Ux Set 4 way teach switches to enable fraud m defence 3 9 Set rotary data switch to position E Switch validator power ON LED will flash Ps LIN ANA o pm LED stops flashing and stays on to indicate Lm successful change m 6 Fraud successfully taught into channel 0 END Taught fraud coin will now be rejected by the validator the next time it is seen 18 MEI 2000 CashFlow 111 User Guide MAINTENANCE The practical maintenance that can be carried out is limited to cleaning the areas of the validator that the coins travel through and the replacement of the coin entry liner if it becomes worn All other servicing is carried out through your distributor The cleaning should be carried out on a regular basis of at least once a month but if you have to visit the validator outside of that routine it is worth while doing it then as well The shaded areas shown below plus the back of the reject cover are those to be cared for The coin entry liner is accessed by unscrewing the coin entry moulding at the top of the validator The coin entry liner can then be eased off with the aid of a fine screwdriver and a replacement slid into place UI Cleaning and maintenance must only be carried out by suitably trained personnel Cleaning must only be carri
4. provided as part of the host machine The recommended fuse value at the rated supply of 12V is 1A Slow blow to EN60127 Other protection methods may be used providing their overcurrent characteristics remain within the overall operating characteristics of the above fuse When used in applications where compliance to BS EN60950 1992 is necessary the host machine power supply must additionally meet the requirements for SELV limited power supplies as defined in BS EN60950 For these applications the coin mechanism should be installed so that it is external to any fire enclosure MEI 2000 1 CashFlow 111 User Guide DOCUMENT GUIDE This document is for field engineers using the CashFlow 111 product produced by MEI As an aid to using this document a series of symbols are used in the text and have the following meanings This indicates that a useful tip or word of advice is shown here a Where this symbol is shown it indicates that a specific action is called for to ensure a successful installation or set up of the product A note regarding the function to be carried out will appear beside this symbol How to recognise the product revision level The revision level of the CashFlow 111 product can be confirmed from a label on the left side of the product There are two levels of digits and bar code markings on the label and the fifth and sixth digits on the lower numbers indicate the product le
5. rejection status of coins tokens N Ivy ANN Flash Sequence Constantly ON 1 Flash 2 Flashes 3 Flashes 4 Flashes Validator Power On Coin accepted Reject lever pressed Coin not recognised and rejected Coin rejected by validator 4th sensor Coin recognised but not accepted due to inhibit setting MEI 2000 CashFlow 111 User Guide Using the Rotary Data Switch and Configuration Switches Rotary Data Switch The rotary data switch is used in conjunction with the configuration switches By pointing the arrow in the middle of the switch using a fine screwdriver data can be entered into the product In Normal Operation mode the position of the arrow is not critical to correct operation Configuration Teach Switches These switches can be set to a series of positions which enable the product configuration to be changed When teach modes are to be entered first SWITCH zm POWER OFF to the unit or an un intended action could Nc m be set om The example given here with both the rotary data switch and the configuration switch settings is to enable channel 3 in the coin set NO Wherever in the examples that follow the switch is shown as hatched grey usually switch 1 it indicates that it does not matter if the switch is in the ON or OFF position Switch 1 only features in the settings for Alarm Enable when it must be in the ON position When itis in the OFF
6. THE CASHFLOW 111 ACCEPTOR USER GUIDE 25648 G3 711463044 CashFlow 111 User Guide Published by MEI Internet http www meigroup com For further information on editions in other languages please write to the Technical Communications Manager at the above address CashFlow 111 acceptor User Guide MEI UK International Ltd 2000 All rights reserved Except as permitted under the relevant local legislation no part of this publication may be copied transmitted transcribed or distributed in any form or by any means or stored in a database or retrieval system or translated in any language natural or computer without the prior written permission of MEI MEI CashFlow and the MEI device are registered trademarks MEI reserves the right to change the product or the product specifications at any time While every effort has been made to ensure that the information in this publication is accurate MEI disclaims any liability for any direct or indirect losses howsoever caused arising out of use or reliance on this information This document does not necessarily imply product availability Part number 711463044 Rev G3 This edition January 2000 Printed in the United Kingdom ii MEI 2000 CashFlow 111 User Guide CONTENTS Safety Summary Product Identification Installation Product Features Configuration Maintenance Product Support Appendix 19 20 21
7. ashing off once and if the coin token is outside of the programmed window it will flash off twice If the LED flashes three time this indicates that the coin token has been rejected by the validator 4th sensor Should the LED flash off four times this indicates either a hardware or software inhibit is being applied Q If further help is required then consult the Operators Handbook for the product or contact either your distributor or local MEI office 8 MEI 2000 CashFlow 111 User Guide CONFIGURATION Configuration Settings The 4 way teach switches can be set up as shown below to configure the product Rotary Switch Switch Switch Switch Mode Selected Switch 1 2 3 4 position s required OFF X X X Alarm Dis abled X ON X X X Alarm Enabled X X OFF OFF ON Machine Interface Type C F X OFF ON OFF Inhibit Coin Token Teach C F X ON OFF OFF Enable Coin Token Teach 0 F X Token Group Select Channel 0 0 D X OFF ON ON Self Teach a Token to Channel 0 E F X Token Group Select Channel 1 0 D X ON ON OFF Self Teach a Token to Channel 1 E F X Discriminator Node ID Select 0 6 X ON OFF ON Fraud Defence Teach Channel 0 E F X ON ON ON Normal Operation X X OFF OFF OFF Normal Operation X Diagnostic LED The LED will illuminate to indicate that the product is powered up and in addition will give various sequences of flashes to confirm the acceptance or
8. ed out after power has been removed from the product L Never use a cleaner containing solvents scrapers or abrasive materials L Never apply water or cleansers directly onto the product Always apply them to a clean cloth first and not too liberally so that the cloth used is only moist Coin entry moulding screw aie 7 g MEI 2000 19 CashFlow 111 User Guide PRODUCT SUPPORT In addition to the MEI offices around the world an international network of Distributors and Approved Service Centres can offer you technical support and other services as well These services include repairs re programming of your CashFlow products with new coinsets replacing damaged modules and the supply of a range of spare parts In the U K these can be obtained from the following WWW MEIGROUP COM 20 MEI 2000 CashFlow 111 User Guide APPENDIX Token Group Selection Table Token Grouping Compatibility ME Product le Token Group ws i LINK Settings Token Type CashFlow CashFlow or Operator 126 129 126 129 AIBICIE Position Position Revision Y Revision G Rank Leisure 1 BFS 2 Ralin amp Thomas LMS Brent Leisure Stretton Leisure MHG Paymaster Claremont Oversized Token Default Brass Wide Brass amp N Plate Brass N P Brass amp Oversized N Plate Steel N Plate Steel
9. es Token material outside allowable limits 1 Switch Validator Power OFF Y dE Set 4 Way switches to Token Teach des 3 E Set Rotary Switch Dial to position F standard PR window limits ls Position E will teach narrow token windows A 4 A Switch Validator Power ON LED will Flash 5M 5 X Drop between 10 and 20 Tokens 6 fes Return switches to Normal Operation LED n should stop flashing and stay on to indicate a a successful change If the LED continues to flash this indicates a failure to teach the token If needed repeat the process from step 1 7 END Token successfully taught amp programmed into Channel 1 14 MEI 2000 CashFlow 111 User Guide Product Configuration Selecting a pre programmed token group to be used in channel 0 14 token groups are already programmed into the product This feature allows a defined token group to be accepted NOTE Each token group selected is automatically copied to channel 0 Refer to the Appendix at the end of the book for further details of token groupings Example To select Token Group 7 on your validator follow these simple steps 1 Switch Validator Power OFF l 2 Set 4 Way Switches to Select Token Group m channel 0 3 T Set Rotary Switch Dial to the appropriate Channel Token group 7 in this example 4 A Switch Validator Povver ON LED will flash e 5 END Return Switches t
10. l normally be supplied in Automatic mode This will automatically configure to most machines through the Mode Select feature Some gaming machines have pre BACTA standard Binary code software and in this case the coin mechanism should be set to fixed Parallel mode Example To set mode to Binary Coded Output 1 N Switch Validator Power OFF 2 o Set 4 Way switches to Output Mode Teach gt E 3 SS Set Rotary Switch Dial to appropriate position W Position C in this example o Switch Validator Power ON LED will Flash 1 A Ss l D prm Set switches 2 3 amp 4 to ON LED will stop ims flashing and stay on Leave the Rotary Switch settings as they are 6 END Product is novv ready for use vvith the chosen machine interface MEI 2000 17 CashFlow 111 User Guide Product Configuration Fraud Defence Teach This feature allows for a fraudulent coin to be taught to channel 0 of the validator so that it can recognize it as a slug and can then reject it This feature requires 3 steps g Enable Fraud Defence i amp N a LN Rt N W Set switches 2 3 and 4 AN o as shown here SN 9 gt E eg 1 Teach the fraudulent coin token as you would a token into channel 0 as shown on page 13 2 Set 4 way teach switches as shown in the example below to identify the channel as a slug se
11. n coin is now inhibited and the product EN D is ready for normal operation For each additional channel to be inhibited repeat process from 1 above MEI 2000 11 CashFlow 111 User Guide Product Configuration Enabling coins or tokens Example To enable channel 2 the 5p coin in this instance on your validator follow these simple steps Channel Enable M oW Set switches 2 3 and 4 as shown here Switch Validator Power OFF 2 tx Set 4 Way switches to Enable Teach 3 o Set Rotary Switch Dial to the appropriate channel est Channel No 2 for the 5p In this instance A 4 A Switch Validator Povver ON LED will flash e 5 Las Set switches 2 3 amp 4 to ON mo LED will stop flashing and stay on The Rotary Switch settings can be left unchanged 6 END The chosen coin is now enabled and the product is ready for normal operation For each additional channel to be enabled repeat process from 1 above 12 MEI 2000 CashFlow 111 User Guide Product Configuration Self teaching a new token channel 0 Example To Teach a Token with standard window limits into channel 0 follow these simple steps Channel Enable o z ea j 45 iil diii LED Flash Codes for Tokens 2 flashes N
12. o Normal Operation LED stops flashing and stays on to indicate successful change Token Group 7 successfully selected and programmed into Channel 0 MEI 2000 15 CashFlow 111 User Guide Product Configuration Selecting a pre programmed token group to be used in channel 1 14 token groups are already programmed into the product This feature allows a defined token group to be accepted NOTE Each token group selected is automatically copied to channel 1 Refer to the Appendix at the end of the book for further details of token groupings Example To select Token Group 7 on your validator follow these simple steps 4 NN 1 N Switch Validator Power OFF i 2 la Set 4 Way Switches to Select Token Group um 3 6 2 Setting Rotary Switch Dial to position 7 selects tr MHG token group A 4 A Switch Validator Povver ON LED will flash 5 END Return Switches to Normal Operation LED stops flashing and stays on to indicate successful change Token Group 7 successfully selected and programmed into Channel 1 16 MEI 2000 CashFlow 111 User Guide Product Configuration Changing the machine output mode To change the coin output interface to Fixed Binary Coded Output BCO use these simple steps For BCO mode set the rotary data switch to position C to D for Fixed Parallel mode and F for Automatic mode NOTE The product wil
13. o activity detected for last 30 seconds 3 flashes Insufficient Tokens 10 min Set switches 2 3and4 9 flashes Token thickness outside allowable limits as shown here 6 flashes Token diameter outside allowable limits 7 or 8 flashes Token material outside allowable limits Switch Validator Power OFF Set 4 Way switches to Token Teach Set Rotary Switch Dial to position F standard window limits Position E will teach narrow token window limits Switch Validator Power ON LED will Flash Drop between 10 and 20 Tokens Return switches to Normal Operation LED should stop flashing and stay on to indicate a successful change If the LED continues to flash this indicates a failure to teach the token If needed repeat the process from step 1 Token successfully taught amp programmed into Channel 0 MEI 2000 13 CashFlow 111 User Guide Product Configuration teaching a new token channel 1 Example To Teach a Token with standard window limits into channel 1 follow these simple steps Channel Enable E NO jr d LED Flash Codes for Tokens 2 flashes No activity detected for last 30 seconds 3 flashes Insufficient Tokens 10 min Set switches 2 3and4 5 flashes Token thickness outside allowable limits as shown here 6 flashes Token diameter outside allowable limits 7 or 8 flash
14. ons will always apply The mounting channel for the CashFlow 111 top entry product is supplied by the machine manufacturer and therefore some variations may exist from machine to machine however in principle these instructions still apply CF111 Front Entry Installation N Retaining clips Q Having ensured that the front plate has a firm location onto the front of the machine insert the side of the validator onto the two round bosses at the rear of the front plate and push firmly together until the two retaining clips are fully engaged MEI 2000 5 CashFlow 111 User Guide CF 111 Top Entry Installation Reject Lever Mounting 7 Point When mounted into a short channel the product must be fully assembled and ready for use with only the machine interface loom to be connected Q The mounting points indicated must be firmly seated into the channel and a gap of between 2 3 mm left between the reject lever and the reject arm from the machine This small gap will ensure that the validator lid is able to fully close when the reject button on the machine has been pressed and released 6 MEI 2000 CashFlow 111 User Guide PRODUCT FEATURES The CashFlow 111 product has the flexibility to change certain settings such as varying the coin set that it handles or new routing for some of the coins tokens These changes can be carried out using the rotary data s
15. position the Alarm function is NOT active L After making any changes the configuration switches 2 3 and 4 m o 1 o MUST always return to either of DOE OR NE the Normal Operation positions m LE shown here before the changes are implememted To Turn ON Or Turn OFF The Alarm If switch one is set to OFF the alarm feature will be dis abled If set to ON the alarm will be re activated Power to the validator can remain ON while the alarm feature is being set thus the LED will continue to be lit at all times N 2 2 M 2 N a N mm CO mug Set for o mnm Set for IB Alarm OFF A m Alarm ON 10 MEI 2000 CashFlow 111 User Guide Product Configuration Inhibiting coins or tokens Example To inhibit channel 2 the 5p coin on your validator follow these simple steps Channel Inhibit N B Set switches 2 3 and 4 Lu as shown here Az 1 Switch Validator Power OFF K NN NO AOA Set 4 Way Switches to Inhibit Teach gt Set Rotary Switch Dial to the appropriate channel sa Channel No 2 for the 5p In this instance fer DN Sye Switch Validator Power ON LED will flash A Ir 4 es 5 len Set switches 2 3 amp 4 to ON LED vvill stop flashing and stay on The Rotary Switch settings can be left unchanged Ii 6 The chose
16. vel For example if the label read 1773Y422580 the revision level would be Y4 Do not use the label on the right side of the product for reference of the revision level Revision Label 2 MEI 2000 CashFlow 111 User Guide PRODUCT IDENTIFICATION MEI has manufactured coin mechanisms compatible withagaming and amusement machines for number of years Over this time the functionality of the range has been enhanced to match your needs and still maintain mechanical compatibility The product detailed in this book is part of the CashFlow series Use the following pages to check you have the right product for your application CashFlow 111 Side Entry CashFlow 111 Top Entry MEI 2000 3 CashFlow 111 User Guide Electrical Interfaces The electrical connections and interfaces to each variant of CashFlow 111 are identical and are found in the same locations A Machine Interface Connector Green Diagnostic LED Machine Interface This provides power to the validator and carries the coin inhibit signals from the machine and coin outputs to the machine 4 MEI 2000 CashFlow 111 User Guide INSTALLATION Installing or removing the CashFlow product from your machine can be done by following these simple instructions When installing the CashFlow 111 side entry product it will be fitted to an MEI Front Plate and the following instructi
17. witch and the configuration switch which are fitted to the CashFlow 111 product The following pages show how with the use of these switches coins tokens can be inhibited or enabled either a new individual token or a group of tokens selected and the machine output mode changed In addition to these two switches there is a green diagnostic LED which signifies if any changes you make have been successfully actioned or not Green Diagnostic TC PLUG Frome ii Cm See ER N See 18 DATA TEACH L Rotary data switch Gonfiaurati n switches ROUTING MEI 2000 7 CashFlow 111 User Guide Coin Token Acceptance When the product is successfully mounted you will need to confirm that it is set up correctly to accept good coins tokens and direct them to where you want them to go First things first UI Press and release the reject button on the machine Confirm that the lid on the front of the validator closes fully when the reject button is released If it does not close fully the validator cannot function properly a Test that power is on by checking that the green LED on the front of the validator is illuminated it will flash off once when the reject lever is pressed Testing for Acceptance Insert into the machine a selection of all the coins tokens shown on the validator label Acceptance of each one will be indicated by the LED fl
Download Pdf Manuals
Related Search