Canon VB-S900F Installation Guide
Contents
1. d lt When powered on during reboot during normal use rs a When Turn Off is selected see Operation Guide c LAN cable d LED 3 Set the camera angle Check the video on the computer s screen and manually adjust the camera s angle Use the camera s Setting Page gt Camera Angle to set the digital zoom see Operation Guide 4 Perform camera settings by using the software found on the Setup CD ROM see Operation Guide If Using a Memory Card e Memory Card Slot f Reset Switch see Operation Guide To remove the memory card push it in and release it The memory card will pop out slightly Important e Insert a memory card before installing the camera e When using a memory card with the camera for the first time it is recommended to format the card after inserting it into the camera see Operation Guide External Dimensions 67 2 64 11 4 0 45 F 114 4 49 0 45 a oO 5 Unit mm in The contents of this guide are subject to change without any prior notice Specifications Please refer to the installation procedures or Operation Guide for specifications not listed below Camera Lens Fixed focal length lens 4x digital zoom Viewing Angle Horizontal 96 0 Vertical 60 5 Interface Network Term2. BIE7003000 Canon Network Camera VB S900F Installation Guide Please be sure to read the Safety Precautions section for correct use After reading this Installation Guide keep it ina readily accessible location for future reference This camera is for indoor use only Z N WARNING To reduce a risk of fire or electric shock do not expose this product to rain or moisture N Caution Request a professional installer for all camera installation work Never try to install the camera yourself Doing so may result in unforeseen accidents such as dropping the camera or electric shock Check Included Items Camera VB S900F Warranty Card Setup CD ROM Notice Installation Guide This document CANON INC 2013 Printed in Taiwan Part Names 1 Mounting Screw Hole A 1 4 20 UNC mounting screw less than 5 5 mm 2 2 in in length will fit the screw hole 2 Lens 3 4 OP 8 f 5 58 OQ 6 7 3 Memory Card Slot Cover 4 100BT LAN Connector 5 External Device I O Terminal 6 Audio Input Terminal 7 Reset Switch 8 LED Installing the Camera Weight Approx 180 g 6 4 oz a Mounting bracket b Mounting screw hole Example installations Using a ceiling mounting bracket Using a wall mounting bracket d Please see the reverse side of this guide for details
3. ct your local city office waste authority approved scheme or your household waste disposal service or visit www canon europe com weee or www canon europe com battery CANON INC 30 2 Shimomaruko 3 chome Ohta ku Tokyo 146 8501 Japan CANON EUROPA N V Bovenkerkerweg 59 1185 XB Amstelveen The Netherlands
4. d when the camera is not in use for long periods e Do not use flammable solvents such as alcohol paint thinner or benzine when cleaning the camera Fire or electric shock may result Only for European Union and EEA Norway Iceland and Liechtenstein These symbols indicate that this product is not to be disposed of with your household waste according to the WEEE Directive 2012 19 EU the Battery Directive 2006 66 EC and or national legislation implementing those Directives If a chemical symbol is printed beneath the symbol shown above in accordance with the Battery Directive this indicates that a heavy metal Hg Mercury Cd Cadmium Pb Lead is present in this battery or accumulator at a concentration above an applicable threshold specified in the Battery Directive This product should be handed over to a designated collection point e g on an authorized one for one basis when you buy a new similar product or to an authorized collection site for recycling waste electrical and electronic equipment EEE and batteries and accumulators Improper handling of this type of waste could have a possible impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE Your cooperation in the correct disposal of this product will contribute to the effective usage of natural resources For more information about the recycling of this product please conta
5. his symbol may result in injury i Failure to follow the instructions accompanied Caution p by this symbol may result in property damage l t nt This symbol indicates important or mportant restricted items Contains reference information for operation or additional explanations Safety Precautions Installation Precautions Warning Do not install in the following places e Places in strong direct sunlight near heat generating objects or subject to high temperatures e Places near fire sources or flammable solvents alcohol thinner fuel etc e Humid or dusty places e Places subject to oily smoke or steam e Places subject to sea air e Confined or enclosed places Fire or electric shock may result Precautions for the LAN power cable e Do not set any heavy objects on the LAN cable e Do not pull forcibly bend scratch or modify the LAN cable Fire or electric shock may result Caution For installation or inspection of this camera consult the dealer where you purchased the product e This installation should be made by a qualified service person and should conform to all local codes e When installing on a ceiling make sure the surface is capable of withstanding the total weight of the ceiling mount cover and the camera and is sufficiently reinforced if necessary e Be sure to use installation screws designed for the type of ceiling the camera is to be installed e Period
6. ically check the parts and screws for rust and to see if they have loosened in order to prevent injuries and equipment damage due to falling items e Do not install in unstable places places subject to significant vibration or impact or places subject to salt damage or corrosive gas Failure to do so may result in the camera falling or other accidents e Be careful not to trap your fingers during installation of the camera Injury may result Caution e Do not install the camera on an unstable or inclined surface e After turning off the power do not turn the power on again for at least 5 seconds e Take measures to remove static electricity before performing any procedures Malfunction may result e Take care not to damage wiring or pipes in the room Damage to peripheral items may result Precautions for Use Warning e If you discover defective conditions such as smoke strange sounds heat or strange odors immediately stop using the camera and contact your nearest dealer Fire or electric shock may result from continued use of the product e Do not disassemble or modify the camera e Do not damage the connecting cable e Do not spill water or other liquid inside the camera spray the camera with water or otherwise make it wet e Do not insert foreign objects into the camera e Do not use flammable sprays near the camera e Do not leave LAN cables connecte
7. inal LAN x 1 RJ45 100Base TX auto full duplex half duplex LAN cables are category 5 or higher with length 100 m or shorter Audio Input Terminal 3 5 mm 90 14 in mini jack connector common for LINE IN amp MIC IN monaural LINE IN x 1 connect to an amplifier microphone or MIC IN x 1 Input x 1 Output x 1 microSD Memory Card microSDHC Memory Card microSDXC Memory Card Compatible External Device I O Terminal Memory Card Others Operating Environment Temperature 10 C 50 C 14 F 122 F Humidity 5 85 without condensation Temperature 30 C 60 C 22 F 140 F Humidity 5 90 without condensation PoE PoE power supply via LAN cable IEEE802 3af compliant Max 4 3 W Storage Environment Power Supply Power Consumption Connecting the Camera Power Supply See Specifications gt Others gt Power Supply Important e Check with your dealer for more information about PoE devices e Some PoE devices allow current limits for each port but applying limits may interfere with performance If using this type of PoE device do not limit the operating current e Some PoE devices have total consumption current limits for ports which can interfere with performance when multiple ports are in use For more information check the instruction guide for your PoE device External Device 1 0 Terminals Wi External Device Input Terminals IN The exte
8. nd connect it to the GND terminal e Do not push the external device I O terminal button with too much force Doing so may cause the button to remain pushed in Internal Connection Diagram 1kO 40kQ 10kQ OIN T Input terminal 0 1 pF pe cen gt _0 OUT 5 Output terminal mo GND 5 g E Q Oo 3 S i Audio Input Terminals Camera has single audio input system supporting two types of microphone input LINE IN and MIC IN Before use change Audio Input on the Setting Page see Operation Guide LINE IN is selected by default e Dynamic MIC IN Input impedence 20 kN 40 kO e Condenser MIC IN Input impedence microphone bias resistance 2 2 kN 20 Microphone power supply plug in power voltage 2 3 V Supported microphones Condenser microphones with plug in power support e LINE IN Input level up to 1 Vp p Use a microphone with an amplifier Symbols Indicating Safety Precautions This Installation Guide uses the following marks to indicate important information the user should know in order to use the product safely In this section explanations are provided for each mark so that readers will understand the level of importance for each Be sure to observe these items Failure to follow the instructions A Warning accompanied by this symbol may result in death or serious injury Failure to follow the instructions accompanied A Caution by t
9. rnal device input terminal consists of a positive terminal IN and negative terminal GND Connecting cables to the positive and negative terminals and opening or closing the circuit notifies the Viewer Important When connecting sensors and switches use those that have terminals which are isolated from internal power and GND i External Device Output Terminals OUT The external device output terminal consists of an OUT terminal and a GND terminal Controls from the viewer can be used to open and close the circuit between the terminals A MOSFET device is used for the output terminal Rating range for load connected to output terminals Rating between output terminals Maximum voltage 50 V DC Continuous load current at or below 100 mA On resistance Below 1 Q Adaptive wiring for external device cables Rating Range same for contact input and output Conductor Size 0 42 0 80 mm 60 017 60 031 in dia AWG No 26 20 Stripped cable length should be approximately 11 13 mm 0 43 0 51 in B Note e The External Device I O Terminal consists of three terminals IN OUT and GND The GND terminal serves as both the external device input GND and the external device output GND e The GND terminal is connected to the camera interior GND e When using the external device input and output at the same time couple the GND wire from the input cable with the GND wire from the output cable conforming to the rating range a
Download Pdf Manuals
Related Search