USER GUIDE - Cardsupply
Contents
1. The Magnetic Encoder dialog box opens when the Encoding Settings button Is selected Track settings is used to select the desired ISO standard for each magnetic strip See the table in this Appendix for information regarding ISO 7811 standards Coercivity sets the magnetic encoding to high HiCo or low LoCo coercivity A magnetic strip that is encoded in high coercivity is more resistant to external disturbance than a magnetic strip encoded using low coercivity Direct encoding is used fo directly encode one or more magnetic strips from this window simply by selecting them and entering the data to be encoded Click on the Send button previously execute encoding to run the encoding cycle Automatic extraction is used to encode magnetic strip cards from applications under Windows such as Word for example A text field enclosed within and characters or some other character which the user can define will be interpreted as an encoding command by print driver Cleaning the magnetic encoder The magnetic encoder head requires regular maintenance in order to ensure the integrity of the data encoded onto cards Cleaning of the magnetic encoderis carried out when the printerruns a cleaning sequence with impregnated cards see the Maintenance section of this manual for further information Repeatedly running the cleaning card through the printer cleans the card feed rollers the cleaning rollers2. Dualus9 Evolis Card Printer 6 2009 All rights reserved August 2014 Ref KUI4E Al Copyright Evolis Card Printer August 2014 All rights reserved Copyright notice Users must observe the copyright regulations applicable in their country This manual must not be photocopied translated reproduced or transmitted in whole or in part for any reason and by any electronic or mechanical means whatsoever without the express written consent of the Evolis Card Printer company All the information contained in this document is subject to change without prior notice Evolis Card Printer cannot be held liable for any errors that may be found in this manual or for any loss or damage arising accidentally or as a result of dissemination or use of this manual Trademarks Dualys is a trademark of Evolis Card Printer All other trademarks belong to their respective holders Warrant Refer to the warranty notice supplied with your printer for warranty terms and conditions and limitations Environmental information recycling of end of life products The manufacture of the equipment that you have purchased required the extraction and use of natural resources It may contain materials that are hazardous to health and the environment To prevent the dispersal of such materials into our environment and reduce the pressure on our natural resources we recommend that you use existing collection systems These systems will appropr
3. 1000 cards Quantum 900 cards 700 cards 1600 cards So for example for a Tattoo2 printer if you insert 50 cards after the cleaning warning Is triggered you have only 50 more cards before cleaning the printer and keeping your warranty valid 19 20 O Insert the cleaning card into the feeder as indicated C e 2 Sa O x C lt Mi 2 O o D 2 Q A 0 E O D u Lo O oe O _ D G a f O O gt O 0 A a Remove any cards found in the feeder Repeatedly running the cleaning card through the printer cleans the feed rollers the cleaning rollers and the print head Follow the procedure below W 6 Put the feeder back into the printer then press on the upper section of the feeder until it clicks O Open fhe cover Remove the ribbon as shown on the diagram Close the cover and check it has clicked shut Hold down the control button on the control panel for one second Cleaning starts i E Wait for 2 minutes after cleaning before using your printer 21 3 3 Servicing the cleaning roller s In addition to routine printer cleaning we suggest that you clean the cleaning roller s using the special wipes available from Evolis The cleaning roller s remove s any dust or particles from the cards before printing Recommended cleaning cycle whenever the ribbon is changed a Servicing accessory cleaning wipe Fol
4. are not flat e The cards are stuck together Press the control button for one second the process will restart e The printer is waiting for a card to be inserted The printer has the Manual card feeder option insert a card into the printer Refer to section 1 Getting started e The printer cover is open Close the cover the printer will restart e The printer must be cleaned See section 3 Maintenance GO GO ZO gt O ao gt gt gt gt CLEANING after 1 200 cards have been inserted OUTPUT HOPPER POSITION MECHANICAL PROBLEM MAGNETIC ENCODING ERROR COOLING MODE 27 e It is imperative that the printer is cleaned See section 3 Maintenance e The output hopper is midway between open and closed Open or close the output hopper The current job will restart e Card jammed in the printer e Mechanical component fault Press the control button for one second If the problem persists contact your Evolis dealer for assistance e The magnetic strip is facing the wrong direction in the feeder e The encoding type is incorrectly configured HiCo or LoCo e The encoded data does not comply with ISO 7811 standards or with the settings predefined in the print driver properties Refer to Appendix C of this manual for further information Press the control button for one second The printer will restart the magnetic encoding cycle with a new card
5. card design to be printed is outside the print margins Check the document orientation portrait or landscape in the print driver configuration 2 Check the interface cable If irregular characters are printed check that you are in fact using the USB cable supplied with your printer Check the connection between the computer and the printer Try using another cable of the same type Check that the printer is clean Clean the printer especially the cleaning rollers See the maintenance section O Check that the cards are clean Store your cards protected from dust O Check the ribbon Check that the ribbon is fitted correctly Check that the ribbon spools freely O Check the print head Should horizontal straight lines appear on printed cards it is likely that the print head is dirty or damaged See the section on maintenance and troubleshooting If the problem persists contact an Evolis dealer or visit the website at www evolis com 32 4 3b FREEING JAMMED CARDS Control panel displays MECHANICAL Print jobs are interrupted PROBLEM A O ec E kw Do not turn your printer off as this cancels pending print jobs in the printer s memory Remove the card as follows O Open the printer cover and remove the ribbon a Press the control button to turn the card transport rollers If the card is still stuck inside the printer slide it manually towards the printer output If there is more than one card always push
6. ensure a lengthy useful life Nonetheless the print head may sometimes need to be replaced Evolis has designed a unique device enabling users to undertake such replacement with no tools needed simply by following the instructions very carefully Before doing anything else please contact your Evolis dealer in order to check the advisability of replacing the print head The dealer will supply a new print head if need be Evolis has set up a scheme for exchanging defective print heads during the printer s warranty period Your equipment is eligible under the scheme if e You use only Evolis consumables ribbons and maintenance products e You have followed the cleaning and servicing cycles scrupulously e You are working in a dust free environment complying with the technical specifications e You are using flat cards with no rough patches which could damage the print head surface 35 To exchange the print head please proceed as follows Before changing the print head please unplug the power cable gt Step 1 Removing the defective print head e Open the printer cover 2 Locate the print head Press on the metal part found at the bottom as shown on the diagram in order to free the lugs from the holding fork then remove the lugs from their slots O Tilt the head carefully and disconnect the connector linked to the cable without using force on the mechanism Z SE 36 Step 2 Inst
7. finished Refer to section 3 Maintenance to carry out cleaning On your printer s control panel the CLEANING light is lit Also service the cleaning roller and then replace the cards and ribbon Once cleaning has been carried out your printer is once again ready to customise your cards 38 4 3e UPDATING THE FIRMWARE UNDER WINDOWS Updating the firmware is a simple operation but one which if not properly completed can result in your printer breaking down Before any update please contact your Evolis dealer who will be able to guide you on the advisability or otherwise of carrying out an Upgrade In general such updates are only required in the event of problem or malfunction that has been clearly identified by your Evolis dealer Updates can be downloaded from the website at www evolis com Select your printer model then click on the Print drivers and Firmware link 2 Then click on the file for the corresponding Firmware Accept the download then save the file in a directory on your hard drive The firmware is stored compressed as a zip file which you will need to extract O Then double click on the file in the directory in order to run the firmware installation program 6 When prompted by the program click on the Download button to run the job The firmware download is in progress O After about thirty seconds the firmware has transferred to the printer and the operation is complete 7 If the printer
8. is facing downwards as shown below a Remove the card feeder from the printer as shown 2 Lower the spring system as shown and insert a maximum of 100 x 0 76 mm magnetic cards chip down 6 Put the feeder back into the printer then press on the upper section of the feeder until it clicks max Contact station interface Printers with a smartcard contact station are fitted with a female DB 9 connector which is found on the back of a printer This connector directly connected to the contact station inside the printer is also connected to an external coupler to program the chip DB 9 connector a External coupler USB serial etc port DB 9 connector pins Smartcard contact points 1 ECHWE C2 reset C3 clock C4 reserved C5 ground C6 Vpp C7 I O C8 reserved C9 ground when the chip is switched with the contact station on CO MWN Oo Bam POF n A sequence of commands must be sent via the printer s interface to insert a card into the printer then position it under the station and establish contact 52 The command sequence is as follows Sending the SIS sequence e Acard is moved from the feeder to the contact station and stops underneath it e The card is pushed Upwards to make contact with the station e The printer connects the contact station to the DB 9 connector e The chip is programmed via the computer s serial interface and the external coupler E Refer to t
9. is not showing a READY status this means that the update has not been carried out correctly or possibly that the printer is not working properly Check the connection cables and run a new update The update is complete and your equipment is ready to customise your cards Never interrupt the transfer between computer and printer during the download phase powering off the printer or computer unplugging a cable This would result in a complete inability to restart the printer Should such an incident occur please contact your Evolis dealer who will replace your printer s processing board 39 4 3f UPDATING THE PRINT DRIVER Updating the print driver is a task that is required in order to fix malfunctions or gain the benefit of new options Before any update please contact your Evolis dealer who will be able to guide you on the advisability or otherwise of carrying out an upgrade Updates can be downloaded from the website at www evolis com 1 Select your printer model then click on the Print drivers and Firmware link 2 Then click on the file for the corresponding print driver Accept the download then save the file in a directory on your hard drive The firmware is stored compressed as a zip file which you will need to extract O Then double click on the setup exe file that you have just downloaded in order to run the installation program E For more details about the procedure please see the Installi
10. section giving answers to the most frequently asked questions FAQ Frequently Asked Questions 41 Appendix A Al Technical specifications This section presents your printer s technical printing properties gt General technical features e Colour printing module e 300 dpi print head 11 8 dots mm e USB connection e Ethernet TCP IP connection as an option e 16 MB RAM allowing two colour cards front and back to be stored e Card turnover point for double sided printing e Detachable 100 card input feeder 0 76 mm or 30 mil e 100 card output hopper 0 76 mm 30 mil e button and 4 LED control panel e Ocean Blue colour gt Printing modes e Colour sublimation and monochrome thermal transfer e Advanced colour management system for top quality photographs e Edge to edge printing e Double sided printing Integrated ribbon saving for monochrome printing gt Performance Performance depends essential on the card design and print settings e Colour 1 side YMCKO 150 cards hour e Colour 2 sides YMCKO K 125 cards hour e Monochrome 1 side up to 1 000 cards hour e Monochrome 2 sides up to 350 cards hour Platforms supported e Windows e Macintosh e Linux gt Software supplied e cardPresso XXS for designing and printing badges e Connects to Microsoft Excel databases gt Ribbon types e 2 panel KO monochrome black ribbon 500 cards roll e 5 panel YMCKO colour ribbon 200 cards roll e 6 p
11. the Evolis printer Programming Guide for further details on programming contactless smartcards 55
12. If the problem persists call your Evolis dealer for assistance e The cooling system has been activated The printer pauses for a few seconds and restarts once it has returned to its normal operating temperature 4 2 Diagnosis help In this section you will find all the information you need to carry out a few simple checks that you may be asked to run by your Evolis dealer to help you as effectively as possible 4 2a PRINTING A TEST CARD We recommend that you print a test card to ensure that your printer is working properly This card shows various technical details for future reference You may be asked for these by your dealer gt Printing a test card ap Wait for any current print jobs to finish 2 Check that there is a ribbon and card in the printer Press the control button for three seconds All the warning lights go out O Press and hold down the control button again 6 The control button light comes on O Release the control button once the light flashes The test card is printed in a few seconds in colour if a colour ribbon is fitted in the printer or monochrome if the ribbon is monochrome 8 The printed card is ejected into the output hopper Information about the test card A test card e Confirms the print quality in colour or black and white e Confirms proper ribbon synchronisation e Displays the printer model e Displays the printer s serial number 28 4 2b IDENTIFYING INSTALLED SOFTWA
13. RE VERSIONS As previously shown you can easily identify the version of the software embedded in your printer firmware number by means of the test card You can also identify the version of the print driver installed as follows From the Start button found bottom left on the Windows task bar select Printers and faxes 2 Select your printer and double click From the Printer menu select Properties O Go to the Graphics tab and then click About 29 4 3 Troubleshootin Do not attempt to use tools or other items to repair your printer in the event of problems in case major damage is caused 4 3a PRINTING PROBLEMS gt Nothing prints 1 Check the print driver Check that there is a print driver for your printer in the Windows configuration Check that the printer is selected as the default printer a Check the printer s power supply Check that the power cable is correctly connected to the printer and to a working electrical socket Check that the printer is on and that the control button is lit Make sure you are using the power supply unit supplied with the printer Check the USB cable Check that the USB cable is connecting the printer to your computer Check the ribbon Check that the ribbon is fitted correctly and that the cover is closed 5 Check the cards Check that there are cards in the card feeder Check that no cards are jammed in the printer O Print a test card See elsewhere in this section f
14. alling the new print head 1 Note the code shown on the white label stuck on the print head You will be asked for this code in Step 3 2 Pick up the new print head and turn it towards you with the white connector visible Connect the cable into its socket making sure if is the right way round Do not use any force as this part is relatively fragile O Turn the head so that the logo is visible be careful the connector can no longer be seen 5 Insert the head vertically between the two guides so that the fork lugs are held within the slot 6 The head is back in position Q Close the cover The print head is now fitted 324 19 00225 B ev LIS gt Step 3 Configuring the new print head ap Power up the printer and check that it is properly connected to a computer on which the printer s print driver is installed 2 Under the print driver s Properties click on the Tools tab In the Printer dialogue section enter the following command Pkn x where x the print head kif code number that you noted in Step 2 For example if the print head kit number is 179 004 00048 the command to be entered is Pkn 179 004 00048 If the print head kit number is not entered correctly printer malfunctions may occur and the warranty may be voided Step 4 Cleaning the printer O O O o E 4 A Cleaning is absolutely necessary after changing the print head No print jobs can be run until the cleaning operation has
15. anel YMCKO K colour ribbon 200 cards roll e half oanel YMCKO colour ribbon 400 cards roll e Monochrome ribbons up to 1 000 cards roll available in black red green blue white gold and silver e Special ribbons hologram clear overlay 350 cards roll scratch off ink up to 1 000 cards roll gt Options Encoding options can be combined e ISO 7811 HiCo LoCo or JIS2 magnetic strip encoder e Smartcard contact station ISO 7816 2 e Smartcard encoder and contact station PC SC EMV 2000 1 e Contactless card encoder ISO 14443A B ISO 15693 Mifare DesFire HID ICLASS e Other specific encoders on request e 100 card additional feeder e Manual card input feeder gt Warranty For best results and to lengthen the useful life of your printer Use original Evolis Genuine Product consumables e Printer and print head 3 year warranty2 unlimited number of print runs Card types PVC and composite PVC cards PET ABS1 and special clear overlaid cards Card format ISO CR 80 ISO 7810 53 98 mm x 85 60 mm 3 375 x 2 125 Card thickness From 0 25 mm 10 mil fo 1 mm 40 mil Double sided printing recommended from 0 50 mm 20 mil Card feeder capacity 100 cards 0 76 mm 30 mil 300 cards 0 25mm 10 mil Output hopper capacity 100 cards 0 76 mm 30 mil 300 cards 0 25mm 10 mil Dimensions Height 235 mm 9 25 Length 447 mm 17 59 Width 237 mm 9 33 Weight 7 4 Kg 16 31 Ibs Connections USD port
16. cable supplied Ethernet TCP IP port as an option Power supply Power supply unit 110 230 volts AC 1 8 A 60 50 Hertz Printer 24 volts DC 3 A Environment Min max operating temperature 15 30 C 59 86 F Humidity 20 to 65 without condensation Min max storage temperature 5 70 C 23 158 F Storage humidity from 20 to 70 without condensation Operating ventilation air cooled Under specific conditions 2 Warranty subject to strict compliance with specific usage and maintenance conditions and the use of Evolis consumables Appendix B BI Compliance statements In this section you will find the certifications for your Evolis printer Compliance statements As regards Safety and Electromagnetic Compatibility Evolis Card Printer 14 avenue de la Fontaine Z 1 Angers Beaucouz 49070 Beaucouz France Equipment name Dualys3 Year of manufacture 2007 Manufacturer name Manufacturer address l the undersigned Monsieur Serge Olivier hereby declare that the equipment named above used and installed in accordance with the notice complies with the essential requirements of Directives 2006 95 EC and 2004 108 EC by application of the following standards EN 60950 1 of 2001 EN 55022 Class B of 1998 A1 2000 A2 2003 EN 55024 of 1998 A1 2001 A2 2003 EN 61000 3 2 of 2000 EN 61000 3 3 of 2000 A1 of 2001 Full name Serge Olivier Position Technical directo
17. cal installation FI Laite on liitett v suojamaadoitus koskettimilla varustettuun pistorasiaan NO Apparatet ma tilkoples jordet stikkontakt SE Apparaten skall anslutas till jordat uttag ap Connect the power cable to the power supply unit then plug the power cable connector into the printer 2 Next plug the end of the power cable into an earthed power socket The printer is powered on and the printer s control panel lights up indicating that the printer is working properly If the control panel does not light then either installation has not been carried out correctly or the printer is not working properly Check the installation Power Ae A USB gt net Before attempting any maintenance ensure that the power cable is always unplugged For your personal safety ensure that the cable and power supply unit remain easy to access especially in the event of an emergency To save energy the printer will automatically switch itself to standby mode after 10 minutes of inactivity gt Connecting the USB cable Under no circumstances should you connect the USB data cable before installation of the printer driver is complete Refer to the section on printer driver installation for further details and follow the instructions carefully 1 3b RIBBONS Evolis original ribbons optimise your printer s operation and avoid causing damage to it The use of ribbons from other suppliers is liable to damage your print
18. ce the manual card feeder in the printer as shown Then press on the upper section of the feeder until it clicks O Insert the cards as indicated 12 Printing E The information about the procedures described in this section refers to a Windows XP environment 2 1 Installing the print driver Configuration of the printer and its driver is a very important step and requires very special care In fact inappropriate settings are a factor having a negative impact on the quality of card customisation It is therefore essential to proceed in stages changing settings only when you are completely sure Evolis offers the option to revert to the factory settings at any time if the adjustments made do not give the expected results Your printer is delivered with a CD containing the print drivers for Windows and Macintosh platforms To install a print driver insert the CD into your computer and select the print driver menu A program will guide you through the entire installation process Do not connect your USB cable to your computer until prompted to do so by the installation program For the connection procedure see the section on Connecting the Printer Follow the installation procedure scrupulously Some versions of Windows and Macintosh require the user to have administrator rights to install the driver 13 2 2 Managing the print settings Before using your printer it is essential fo check and or change the default pr
19. ched either through the card feeder or through the inside of the printing unit when the cover is open The printer accepts cards between 0 25 mm and 1 mm thick The factory setting for card thickness is 0 76 mm Adjusting card thickness through the feeder cage O Remove the card feeder from the printer as shown 2 Adjust the thickness of the cards used by moving the lever from right to left to the desired card thickness Put the feeder back into the printer by pressing on the upper section of the feeder until it clicks 10 Adjusting card thickness from inside of the printer ap Open the printer cover by pressing on the opening lever then tilt the cover up 2 If necessary remove any ribbon inside the printer Then adjust the thickness of the cards used by moving the lever from right to left to the desired card thickness Replace the ribbon in the printer then close the cover gt Inserting cards manually The printer may optionally be equipped with a manual feeder for inserting cards individually The manual feeder option needs to be configured via the printer driver s Properties under the Graphics tab Choose Manual feed from the Card management input menu and select the desired output method from the menu The manual card feeder is installed as follows O Remove the card feeder from the printer as shown 2 Using the lever set the card thickness to the MAX position Pla
20. d contactless smartcards Cla MAGNETIC STRIP ENCODING A printer fitted with a magnetic encoder works in exactly the same way as a basic card printer The Evolis encoder encodes the magnetic strips in a single pass then runs a data check Configurable as high coercivity HiCo or low coercivity LoCo by a simple click in the Windows print driver Evolis magnetic encoders are however shipped with a default setting of high coercivity HiCo unless otherwise requested when placing the order Location of the magnetic encoder The magnetic encoder is a module fitted in the factory The read write head is located under the path taken by the cards and after the print head The encoding sequence for a card is always carried out before the printing Use only magnetic strip cards that comply with ISO 7810 and ISO 7811 standards i The magnetic strip must be moulded into the card to work properly Never use cards with a glued on magnetic strip Card positioning Magnetic strip cards must be placed in the card feeder so that the magnetic strip is facing upwards as shown below a Remove the card feeder from the printer as shown 2 Lower the spring system as shown and insert a maximum of 100 x 0 76 mm magnetic cards Put the feeder back into the printer then press on the upper section of the feeder until it clicks max tefl Magnetic encoder i Track settings Track Settings to set tee features of
21. damage or quality problems caused by using non Evolis approved ribbons Evolis provides replacement parts and consumables that you can refer to within this user guide or by visiting the website at www evolis com 18 3 2 Routine printer cleanin The print head warranty is directly linked to routine cleaning of your printer If you do not carry out this cleaning at the required times the print head warranty will cease to be valid Recommended cleaning cycle whenever the ribbon is changed Mandatory cleaning cycle when the cleaning warning is triggered Servicing accessory cleaning card Your printer is fitted with a cleaning warning system which is triggered after a certain number of cards have been inserted depending on the model of printer that you have see table below AN You should proceed with the routine cleaning of your printer as soon as the warning is triggered If you continue to run the printer despite the warning and if the warning light starts to flash the print head warranty will be automatically voided owing to a failure to comply with your contractual maintenance obligations Number of cards remaining Cleaning required after Warranty invalid after before warranty voided Tattoo2 400 cards 100 cards 500 cards Tattoo RW 400 cards 100 cards 500 cards Pebble4 1000 cards 200 cards 1200 cards Dualys3 1000 cards 200 cards 1200 cards Securion 800 cards 200 cards
22. each track track 1 Tap1 801 accepte up to 76 alphanumeric characters from A to Z and from 0 to 9 as well as ASCII characters a b 5 Track 9 isoa Dot accents L pa ak m po from ta 5 as w l as ASCI characters bebw en 48 and 62 L l 1803 accepte up to 104 numerical dgis fom 0 to 9 as well as ASCII characters bebaeen 48 and 62 Track 3 lisoa SIPASS accepts up to 21 characters from 16 to 127 ASCI characters CE Mode allocated to a speo ic use in the future Jina Japon 5 C4 Markt alkscnatad ta a specific u in the future Coerchaty sets Gre ren high or kow Coeyanaty HO LEON EE cosy mage shipe is more reshen bo exbernal disturbance than a magnetic stipe er oily Direct encoding Coerdhty Track 1 Lew concret Track 2 r a High coercivity Track J a Get omer Serd en Encoding through an application Configuring the Windows print driver When first installing the Windows print driver the magnetic encoder functions need to be configured The magnetic encoder functions are found in the print driver s Tools dialogue box by clicking on the Encoding Settings button Magnetic Encoder dialogue box Auto chebecton lead in oode To encode fom your application or document insert a data string inctes tie repo folowed by the data and bounded by character fo IDATA gt encodes the DATA data on track 1 Tradineode cm apot Reset to default seringe
23. er and voids the manufacturer s warranty for the printer For optimum print quality Evolis recommends that the printer is fully cleaned every time the ribbon is changed See the Servicing and Maintenance section of this manual gt Fitting the ribbon E Ensure that the appropriate ribbon type is selected in the print driver 1 Open the cover e Insert the ribbon as shown 6 Close fhe cover and press until a click is heard 7 1 3c CARDS For optimum quality the cards used must be ISO 7810 certified Use only the card types recommended by Evolis Do not touch the printable surface of the cards in order to preserve print quality Do not use cards that have been damaged folded embossed or dropped on the floor Keep your cards protected from dust Loading the cards 1 1 Remove the card feeder 2 Turn the feeder over and insert the cards Ensure the cards are positioned as illustrated in the diagram Put the feeder back into the printer and press until a click is heard O gt Removing printed cards Once the print cycle is complete cards are delivered into the output hopper found on the left of the device This output hopper is designed to collect the printed and or encoded cards The printer is equipped with an output hopper with a capacity of 50 x 0 76 mm cards Adjusting card thickness The printer is equipped with a manual card thickness adjustment mechanism which can be rea
24. et us know by emailing us at info evolis com Contents The bookmarks found top left of your screen can be used to navigate between the various sections in this user guide Icons The following icons are used in this manual to highlight important information L z Information providing further details or depth about certain points in the main text Indicates that failing to take the recommended action is liable to damage your printer This symbol indicates that a video showing the procedure is available on the www evolis com website Getting started 1 1 Unpacking Your printer is supplied with several accessories that we ask you to look at closely This list may vary depending on your location The printer is shipped in special packaging designed to prevent any damage in transit If you notice any visible damage do not hesitate to contact the shipper and immediately inform your Evolis dealer who will tell you the procedure to follow Evolis takes great care over the quality of its packaging and we ask that you keep this packaging somewhere clean and dry You will be asked for the full original packaging outer box inner wedges and protective bags in the event that the printer is returned If the printer is returned without its original packaging and components are damaged in transit these components will no longer be covered by the warranty You will be charged for new packaging for shipping the printer back to y
25. factorily Keep your warranty cover The manufacturer s warranty is subject to strict adherence to the routine servicing and maintenance instructions and in particular the printer cleaning cycles Any failure to follow the maintenance and servicing procedures described in this section voids the print head warranty Evolis declines any liability where there has been a failure to carry out required maintenance on the printer The print head is a wearing part and an extremely sensitive printer component Its useful life can be seriously curtailed by the presence of dust liquids or solids in the printer s immediate environment on the print head or on the cards Users must take all necessary precautions to insert only clean cards free of dust deposits or foreign bodies into the machine The frequency and quality of cleaning are decisive factors enabling users to extend the print head s useful life and to ensure excellent print quality Particular care must therefore be taken with cleaning Users must comply with the servicing and maintenance instructions as fully described in this section In addition the use of Evolis brand ribbons Evolis Genuine Ribbons also ensures that your equipment operates properly Use of ribbons not approved by Evolis may as a consequence affect the quality and reliability of print jobs produce low quality printed output and even affect the printer s operation The manufacturer s warranty does not cover physical
26. he Evolis printer Programming Guide for further details on programming smartcards The Evolis product catalogue has printers equipped with a chip contact station and a built in encoder Depending on the model these encoders connect to the PC via an RS 232 interface DB 9 socket or a USB interface Clic CONTACTLESS SMARTCARD ENCODING Evolis printers may be equipped with an encoding device for contactless smartcards RFID This consists of an encoding module and sometimes a detachable antenna Integration of such a module must be carried out by specialist The Evolis product catalogue has printers equipped with a built in encoder for contactless chips Depending on the model these encoders connect to the PC via an RS 232 interface DB 9 socket or a USB interface There is a very wide variety of contactless cards and each card has specific technical properties associated with an equally specific type of encoder See your Evolis dealer for further information Location of the antenna or the encoder including an antenna By means of a specific command the card Is positioned close to the antenna such that the card lies within its radio range Reading data from or writing data to the card can then start The programming sequence for a smartcard is always carried out before the printing Card positioning On the face of it there are no restrictions on card positioning when programming in contactless mode However the miniaturisatio
27. he distance between the equipment and the radio or television Connect the equipment to a circuit other than that to which the receiver is connected Consult the supplier or an experienced radio TV technician Use of a shielded twisted pair cable is necessary to comply with the restrictions laid down by part 15 of the FCC Rules for Class B digital devices Pursuant to Part 15 21 of the FCC Rules any changes or modifications made to this equipment without the express written consent of Evolis Card Printer may cause harmful interference and void the FCC authorisation to operate this equipment Japanese radio frequency interference VCCI This equipment is Class B information technology equipment based on the rules laid down by the Voluntary Control Council For Interference by Information Technology Equipment VCCI Its use in or close to a residential area may cause radio interference in which case you must take appropriate steps ORL AHLERS EEA RaW VCCI OHH K DI VTS ABRRRMERTT NERS KF ERRETRAJSTIZE ABRELTUERTS CORP S rT LEY 3 LRISMICI EL T tAn SERR ASAE TIt ra NET HR ER AB CZ CIE L LIEU Usa LOPS Appendix C C1 Encoding options Some models of Evolis printers are equipped with encoding systems which are used to customise magnetic strips and contact and contactless smartcards Depending on the model if is possible to install up to three types of encoder in the printer magnetic strio contact an
28. iately re use or recycle most of the materials in your end of life equipment bad The crossed out dustbin symbol on your device is a reminder to use these systems pe If you need further information on collection re use and recycling systems contact your local or regional waste management body Do not hesitate to contact us to find out more by visiting our website at www evolis com or by emailing the following address info evolis com About your new printer Thank you for choosing an Evolis printer Using your new printer you will be able to create a wide variety of high quality cards and badges which can be printed in various thicknesses colours and styles This printer uses consumables and accessories available from Evolis For further details visit our website at www evolis com Warranty registration Please register on line at www evolis com to receive our special offers and general information Once on the website click on Drivers and Support and fill in all the fields giving in particular the model and serial number found on your printer Getting started The purpose of this User guide is to guide you step by step through your printer and how if works Take some time to read it in order to better understand your printer and its features and to save time during installation and use As with all Evolis products a great deal of care has been taken over this manual Should you find an error however please l
29. int driver settings e Ribbon type e Card type e Card finish or treatment You will find more detailed information about the cards recommended by Evolis in the Evolis Genuine Product list of consumables Pay attention to the settings defined under the print driver Properties and do not hesitate to contact your Evolis dealer for any advice and assistance needed before making any changes These print settings are accessible e From the Start button found bottom left on the Windows task bar select Printers and faxes e Select your printer and double click e From the Printer menu select Properties e The first properties configuration screen for the equipment then appears e The main tabs used to define the settings are Graphics and Tools 14 gt Graphics tab is Ribbon or card types SPAT EANA e Front back printing Choice of methods for feeding and collecting cards e Card orientation portrait or landscape Number of copies Tools tab e Setting and testing magnetic encoding options e Test card printing e Cleaning the printer Dialogue interface with the printer We recommend that you print a test card when first using the printer and keep it This card records information such as the model and serial number which you could be asked fo provide if you call technical support 2 3 Printing a card A large n
30. low the procedure below GD Open the cover and remove any ribbon 2 Remove the cleaning roller Rub the wipe gently over the surface of the roller O When it has dried replace the cleaning roller in the printer E Wait for 2 minutes after cleaning before using your printer 22 3 4 Servicing the print head W Recommended cleaning cycle whenever the ribbon is changed NOT ao e Non Servicing accessory Special cotton bud impregnated with isopropyl alcohol The print head is cleaned in the course of the printer s routine servicing procedure see previously However fo maintain the original print quality and to absorb surplus ink on the print head we recommend that you regularly clean the print head whenever the ribbon is changed using the cotton buds supplied by Evolis You must also protect the print head and its components from any discharge of static electricity Unplug the printer from its power supply before cleaning the print head Follow the cleaning cycles scrupulously Avoid any contact between the print head and any metal or sharp objects Avoid touching the print head directly with your fingers as this could affect print quality or permanently damage the print head 23 Follow the procedure below O Take an Evolis cotton bud and press the middle of the tube until the end of the cotton bud is impregnated with alcohol SAN 2 Open the cover and find the print head Gent
31. ly rub the cotton bud from left to right along the print head for a few seconds O Close the cover f EN l Z NS FR AS Wait for 2 minutes after cleaning before using your printer 24 Help This section gives a number of suggestions allowing problems that may arise when using your printer to be pinpointed If you do not manage to solve your problem this section also explains how to contact Evolis technical support 4 1 Warnings and diagnosis Although the Evolis printer was designed to work independenily keeping user involvement to a minimum it may nonetheless prove useful to gain some familiarity with the main warnings 4 1a CONTROL PANEL WARNINGS See section 1 Description of the printer and its functions for further details about the control panel OFF STEADY LIGHT FLASHING PRINTER READY e The printer is ready to receive data PROCESSING e The printer is receiving data 25 ao ao O G O G O gt gt O gt O gt O gt RIBBON CARDS WAITING FOR A CARD PRINTER COVER OPEN CLEANING after 1 000 cards have been inserted 26 e No ribbon in the printer e End of ribbon e The ribbon is not correctly fitted e The ribbon is torn Check the condition of the ribbon in the printer If you have a print job in progress this restarts with a new card e The card feeder is incorrectly installed e No cards in the card feeder e The cards
32. n of components is bringing about the emergence of cards fitted with mini antennae In this situation please see your card supplier for further information about where such mini antennae are located within the card so as to present the card as close as possible to the encoder s antenna Doing so will ensure optimum encoding of the cards Computer connection If your encoder is supplied with an USB interface it will either be connected to the printer s internal USB Hub or equipped with a USB cable to connect to your computer directly in the first case your printer s USB cable is used to drive firstly the printer and secondly the encoder from the computer If your encoder is supplied with an RS 232 interface it needs to be connected to the computer via a serial cable This cable plugs into the printer s female DB 9 socket and into a COM port on the computer Not used RxD TxD Not used Not used Not used RTS CTS Not used E OO MN Bam EH A sequence of commands must be sent via the printer s interface to insert a card in the printer then position it close to the antenna to establish radio communication between the card and the encoder The command sequence is as follows Sending the SIC sequence e Acard is moved from the feeder towards the antenna and is positioned nearby e The chip is programmed via the computer s serial or USB interface connecting the built in encoder and the computer E Refer to
33. ng the print driver section 40 4 4 Technical support If you are having difficulties in configuring and using your printer read this manual carefully If you do not manage to solve your problem you can obtain further information and help from the Evolis partner network 4 4a EVOLIS PARTNER NETWORK For any unresolved technical problem contact an Evolis dealer If you do not know any Evolis dealers visit the www evolis com website and send us your question Evolis will pass on the contact details of your nearest Evolis dealer When calling an Evolis dealer you do need to be close to your computer and ready to provide the following information Your printer model and serial number 2 The configuration and operating system that you are using A description of the incident that has occurred O A description of the steps that you have taken to resolve the problem In addition to enable you to find answers to your questions 24 7 the www evolis com website includes a number of aspects related to day to day use of your printer 4 4b FINDING INFORMATION ON WWW EVOLIS COM If you need additional technical help you will find a great deal of information on using and troubleshooting Evolis printers under the Drivers and Support section on the Evolis website at www evolis com This section offers downloads of the latest versions of firmware print drivers and user manuals videos about using and maintaining Evolis printers and an FAQ
34. or the procedure to be followed ev LIS gt Blank card ejected Check the ribbon Check that the ribbon is not finished or damaged Replace it or re install it if necessary 2 The print head may be damaged Print a test card If the test card does not print contact an Evolis dealer for technical support or visit the website at www evolis com 30 gt Poor print quality Small blemishes on the card The card surface may be dirty Check that your cards are perfectly clean Use new cards e Cleaning rollers or print head clogged Clean the cleaning rollers and print head Horizontal white lines e The ribbon is not correctly fitted Check that the ribbon is correctly positioned in the printer Check that there are no wrinkles on the ribbon surface Print head dirty or damaged Clean or replace the print head Blurred image The ribbon is not correctly fitted Check that the ribbon is correctly positioned in the printer Poor ribbon synchronisation Open and close the printer cover to synchronise the ribbon e Dirty printer or cleaning rollers Use of incompatible cards Check that the cards used match the specifications We recommend that you obtain your cards from an Evolis dealer Use of cards obtained elsewhere is liable to adversely affect print quality and or damage the print head gt Partial or incorrect printing D Check the print settings Check that no area of the
35. ou Accessories supplied with your printer Power supply unit VP ELECTRONIQUE or SWITCHBOX Type F10723 A or Type EA10723 e Mains power cable p USB cable Installation and documentation CD ROM Starter cleaning kit e Quick installation guide e Warranty notice e Compliance statement documentation If any of these components is missing please contact your Evolis dealer Use only the power supply unit supplied with your Evolis printer VP ELECTRONIQUE or SWITCHBOX Type F10723 A or Type EA10723 Use only the USB cable supplied with your Evolis printer The Evolis printer must be placed in a dry location protected from dust and draughts but well ventilated Take care to keep your printer on a flai sturdy surface able to bear its weight 1 2 Description of the printer and its functions U Control No cards button Cleaning A Output hopper F Carrying handle B Cover opening button G DB 9 connector option C Card input feeder H Power cable socket D Control panel USB socket std E Manual card feed option J Ethernet socket option O O D O O Cc ao Q E 3 O O Aa D O OO 2 copes x FV DYE 2 oeree Co PWE SSF OHO v OSVOF h I l l un SE ZOO A n 7 A 1 3 Installation 1 3a CONNECTING THE PRINTER Connection to the power supply The printer must be connected to a properly protected and earthed electri
36. r Date mars 2007 a Signature EUROPE Norway Only This product is designed for IT power system with phase to phase voltage 230V Earth grounding is via the polarized 3 wire power cord FI Laite on liitett v suojamaadoitus koskettimilla varustettuun pistorasiaan SE Apparaten skall anslutas till jordat uttag NO Apparatet m tilkoples jordet stikkontakt 45 FCC Federal Communications Commission notice Radio frequency interference in the United States w Dualys3 models comply with the following specification FCC Part C 15 Subpart A Section 15 107 a and Section 15 109 a Class B Digital device Additional information This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try the following measures Reorient or relocate the receiving antenna Increase t
37. r comes configured in DHCP mode Dynamic Host Configuration Protocol which means that its IP address is supplied by the network In addition to these basic settings the network administrator has the option of configuring the printer differently in order to comply with the constraints imposed by the corporate LAN e Printer connected in a subnet in DHCP e Printer connected within a subnet with fixed IP address with WINS resolution e Printer connected within a subnet with fixed IP address without WINS resolution The printer may be identified on the network in two ways e By its hostname NETBIOS e By its IP address The user definable settings are e The printer s IP address e Subnet mask e Gateway e WINS server Changing the printer s basic settings without prior knowledge of the layout of the LAN in question or without genuine technical knowledge may result in a malfunction of the printer and may even extend to a more widespread failure of all or part of the LAN Contact your System and Network Administrator before connecting to or changing the settings for your local area network For further details refer to the Configuration of Evolis printers on a TCP IP Ethernet LAN manual 17 Maintenance 3 1 General warranty information Your Evolis printer has been designed to give you long service and needs only minimal regular maintenance Please comply with the instructions given below to ensure that it runs satis
38. the print head and the magnetic encoder read write head If in between two routine printer cleaning runs every 1000 cards inserted the read write process fails with more than one card it is recommended to run a printer cleaning sequence manually please see the Maintenance section of this manual for the procedure to follow 48 Ww gt SO 7811 magnetic encoding standards Alohanumeric EE ZOER ASCII 20 95 Numeric e 1 3 Fab Pee ASCII 48 62 Numeric pi 1 3 Piste 3 210 ppp ASCII 78 62 107 bits per inch 2 Except for the 2 character 3 Including the Start Stop and LRC characters which are automatically handled by the magnetic encoder 49 Clb CONTACT SMARTCARD ENCODING A printer fitted with a smartcard contact station works in exactly the same way as a basic card printer The Evolis smartcard contact station is used to program chips to ISO 7816 2 standards Contact station location The contact station is a module fitted in the factory It is located over the path taken by the cards and before the print head To make contact with the station the smartcard is positioned underneath it and is pushed mechanically upwards The programming sequence for a smartcard is always carried out before the printing Use only smartcards compliant with the ISO 7816 2 standard Never print over the chip Card positioning Smartcards must be placed in the card feeder so that the chip
39. the top one first Replace the ribbon then close the printer cover O Press the control button on the control panel for one second To prevent card jams 1 Check that the card thickness gauge is correctly adjusted 2 Check that the thickness of the cards used matches the specifications set out in Appendix A Technical specifications in this manual Check that the cards are flat Keep them in a horizontal position O Check that the cards are not stuck together Shuffle the cards before loading them 33 ev iS 4 3c REPLACING THE CLEANING ROLLERS Should your cleaning roller start to work less effectively despite regular maintenance it is advisable to replace it in order to avoid dirt accumulating on the print head resulting in permanent damage See section 3 Maintenance The cleaning roller is available as a consumable from your Evolis dealer Roller replacement procedure 1 Open the printer cover 2 Remove the ribbon if any then locate the cleaning roller and release it from its housing Fit the new roller in the printer ensuring that it is correctly positioned in the housing O Replace the ribbon and then close the printer cover f LES ra f RSS Z ISS a gt 34 4 3d REPLACING THE PRINT HEAD The print head is a sensitive component of your equipment If determines the print quality and regular servicing along with an immediate environment free from dust or other particles
40. umber of Windows applications allow documents to be printed for example the tools in Microsoft s Office suite i e MS Word MS Access Ms Excel MS PowerPoint To gain familiarity with the layout ofa card and configuring its formatting and printing we suggest the following example In Microsoft Word After having set the Evolis printer as the default e Start the MS Word application Click on the File in the menu bar then on Page Setup e The Paper tab has a Paper Size option select CR80 Card In the Margins tab set all margins to 0 then in the Orientation section select Landscape e Close the window by clicking OK Your Word window should now look like this x Abad ori Sales PCF Bebe Eden Siege melon Format Guth Tabi Fonte t l Bea Pee L 97 0 AAA A IBM T me ave D You are ready to customise your card by adding the various items that go fo MAKE dimma remen e lo s E ami ERR EAD Up a card e Logo and Illustration e Identification photo e Fixed and variable text e Bar code etc Once ready click on File and then on Print 4 Desine up Fognesautonstiquerr a PO ca A 5 UN aride dr m SE eB af Page Sec l LA A Q on Li l Col l Auger Eg 2 4 Connecting to a network Ethernet All Evolis printers have the benefit of a TCP IP network connection mechanism This feature is available as standard or as an option depending on the model in the range Out of the box the printe
Download Pdf Manuals
Related Search