User Manual
Contents
1. That the Unit is warming is indicated by a temperature lamp being lit Wait about 10 seconds after start If the unit do not self test exactly as described in this manual then you must not use it Warming can only start if no faults are detected Temperature indication and selection The actual water temperature is indicated by a blinking lamp and the selected by a constantly lit lamp That the selected temperature is reached is indicated by a constantly lit temperature lamp The temperature lamps have different colours as described below Lamp Colour Temperature range Comment Symbol s Green 35 37 C Selected by pressing the temperature button Yellow 34 34 5 37 5 and 38 C Can only be selected if the temp lock key is pressed and hold in at the same Ga time Red 20 30 and 39 42 C Only for indication Alarms Description and checks of the function of alarms is found in the technical section Stop the acoustic alarm by pressing the alarm button or switch the unit off by pressing the Start Stand By button Only AT can be cancelled for 10 minutes by pressing the alarm button Try to rectify the cause for an alarm see section trouble shooting and switch on the unit again If the alarm still goes on contact a qualified technician Please follow the Quick Start instruction on page 3 Ensure that all parts are available and in good condition See also the video Handling Instructions Always place the KANMED Baby Warmer on2. 10 cm upwards Press the air bubbles towards the hole repeatedly until all major air bubbles are expelled 12 Lower the filling hole while pressing the Water Mattress so that no air enters and insert the plug 13 Turn the Water Mattress upside down and insert the Heating Pad in the pocket 14 The Water Mattress and the Heating Pad is inserted into the KANMED Baby Nest The KANMED Baby Nest Different types of KANMED Baby Nests are available Please check with your supplier or on internet www KANMED se The KANMED Baby Nest is intended to prevent the baby from rolling off the water mattress to facilitate correct positioning and to create a tight and cosy environment around the baby By pulling the strings one can adjust the collar from being wide open and flat to become a tight raised wall around the baby The Baby Nest consists of a bag into which the Water Mattress and Heating Pad is inserted Note Check the Baby Nest regularly for damages To reduce the risk of a nest splitting during washing we recommend that the nest is used for only one year Page 7 of 16 KANMED BABYWARM ER User Manual Bw 50 070 10 Start and self test Every time the Control Unit is switched on it performs a self test of all functions and the internal safety circuits See chapter 10 for a detailed description of the self test If the Control Unit does not detect any faults the warming will start automatically at a factory pre set temperature of 37 C
3. has ended 3 Check that the warming starts i e that the missing or dead battery can be bypassed Your local supplier has all information about available spare parts and accessories or check www KANMED se User Manuals in many languages can be downloaded from www KANMED se KANMED or your local distributor will provide a spare part price list as well as a service manual that contains all information necessary to perform maintenance and simpler repairs Article number Description Quantity BW 50 002 Heating Pad BW50 1 BW 50 003 Water Mattress BW50 1 BW 50 025 KANMED Baby Nest 1 5 pack available BW 50 005 Filling Tube BW50 1 BW 50 029 Anti algae Box of 20 BW 50 007 Battery Cable for Control Unit 1 BW50 Spare parts 700 0001 Fuse T 1A F1 F2 220 240V Pack of 10 700 0079 Fuse T 2A F1 F2 110 115 V Pack of 10 700 0324 Fuse T 3 15A F3 F4 Pack of 10 699 1171 Mains Cord 230V 1 Page 13 of 16 KANMED BABYWARM ER User Manual Bw 50 070 10 Heating Pad Voltage 24 Volt AC from Control Unit BW 50 when powering with mains power or 24 V DC when powering from 24V battery source Power consumption 50 Watt 12 Watt when powering the Control Unit from a 12 Volt battery Dimensions and Weight Length 580 mm With 250 mm Thickness 2 mm Weight 0 5 Kg Length of connection cable 1 2m Material cover PVC Watertight Yes except connector Conductivity surface Not electrically conductive Radiation No measurable magnetic and elect
4. mattress or there is no water in the mattress Correct the position of the Heating Pad and or add water in the Water Mattress lamp is lit The Heating Pad is not connected Check pad connection Heating Pad is faulty Try another Heating Pad lamp is lit Technical fault in Control Unit Leave the unit to a technician Element in the Heating Pad might be faulty Check with another Heating Pad or leave it to a technician AT 46 snd Co are blinking Internal 1 5 V battery low or missing and must be replaced as soon as possible Battery has to be replaced by a technician Bypass by making a new start but keep the Alarm button pressed continuously until the self test has ended Test instructions Self test at start Connect the control unit to mains supply and Heating Pad Switch on the mains switch at the rear panel and check that the mains indicator lamp is lit Press Start Standby and check that the following happens in the order described below oe a All alarm lamps are lit and the beeper sounds for about 0 5 sec All lamps starting from Control unit lamp and ending with 42 C are lit in consecutive order One of the temperature lamps blinks 5 times indicating PROM version Temperature lamp 37 is lit If the self test is performed as described above it is ready for use Over temperature alarm AUNE on Start the unit and observe self test is OK Fill a buck
5. temperatures 4 Button for setting temperatures outside the 35 37 C range 5 Indicator for Mains power 6 Indicator for battery power 7 Alarm indicators 8 On Off Start button 9 Silence alarm button Rear Panel 1 Earth potential connection stud 2 Mains voltage indicator 3 Fuse holder 4 Locker for fuse holder 5 Heating Pad connector 6 Mains switch 7 Mains socket 8 Connector for The Heating Pad Indicators not selectable temperatures external 12 24V battery Avoid bending the Heating Pad The design and construction of the Heating Pad has reduced magnetic and electrical fields to normal background levels and thereby making them harmless The voltage to the Heating Pad is SELV 24V DC Safe Extra Low Voltage See technical data for information about warming up times Explanation of the drawings on the Heating Pad Please make them available while reading this C1 R NTE Heating Pad BW 50 002 may only be connected to Control Unit BW 50 Never place a baby or a child directly on the Heating Pad The Heating Pad must be inserted in the pocket under the Water Mattress The correct amount of water is obtained by filling the Water Mattress to the level mark The Heating Pad must be inserted into the pocket of the Water Mattress with its illustrations facing the Water Mattress This is best done if the Water Mattress is placed upside down on a flat surface The Heating Pad and the Water Mattress shall not be
6. User Manual KANMED BABYWARMER Art No BW 50 070 10 2010 05 CE 0413 Caution Please read this manual carefully Incorrect use of patient warming equipment may cause patient injury Manufactured by KANMED AB Sweden Distributed by KANMED BABYWARM ER User Manual Bw 50 070 10 1 KANMED Baby Warmer Quick instruction sssssssssrsssrrssserssnerssnersrnrrrrnrrr ene rn KKR eee RR KKR KRK K RAR A 3 2 Safety INStFUCTIONS sed coins edict ease aces ae a adel oe fr Jar aAa aah au RA Ar tia cel Re Ro Ar ER 4 3 General deScriptOniivscis coiss asia senses sk pira DENNE pea aes devas Rd DES E 5 4 Description Of TUNCHONS sasson sr ra RE ERE DE ENANA REA KORR EE ENN NY RE OR EE ans 8 5 Getting ready Tor the Baby semester rss as ke be se ere Nea rare RS RR 8 6 Daily use and practical Nints isini ee aa Ae RA RJ aAa JAR RAA HA ra SA KKR RAR KKR 8 7 Cleaning and mYalntenaNCE ssskmsmdsssissnas ss Vs Ve a RN RN oe RER EEE a ER ER ER 9 8 Alarm functions ANd INdICATION so ssne sbovs ssd ena ej N ere A br ra RR ja re ch 11 9 Trouble SNOOCING isisi san ae salve ara er R na f GR af ja ea AEA fa rr ag HERA JAR EA ar KR KE RE a RER 11 10 Safety systems availa ble ss vs Mee Oss aa kh a RARE RE JEN Mk EEE ER 12 11 Accessories Spare parts and technical dOCUMEnNtatiON ssserrsserrssrrrrrrrrrrrrrrrrrrr rk rr rr rna 13 12 Technical data versida dr ar an arg a Er ad Ae af ar Dj AEA EA RER JA RER EF RARE a KBR es 14 13 Wall
7. an yc veces ls dee E eo ee a F a RE RE ENE EE RR ER ARR ARENA ARR SEE N 15 14 DIS O S Ni4 ret canscaeiannaebeiehara uthbadeag a er r Re Ny re RAA SA Br i NR jer ra N 15 NOTE This manual is valid for all KANMED Baby Warmer of model KBW50 recognised by the blue silicone rubber edges on the control unit This user manual contains important safety information and must be read carefully and shall be saved for future reference KANMED Baby Warmer placed in the KANMED Baby Bed A perfect combination Page 2 of 16 KANMED BABYWARMER User Manual Bw 50 070 10 Always leave the unit switched on so that it is ready for the next baby Refer to the Users manual whenever in doubt Se also the Baby Warmer Video Handling Instructions Filling the water mattress 1 2 3 4 Use the filling tube to fill the water mattress with warm water about 35 C Fill to the level mark Check by standing the water mattress upright If the bed is to be tilted please read chapter 3 Water Mattress in the users manual Add one complete bottle of KANMED anti algae preferably via the filling tube There must be no air in the water mattress Place the water mattress on a flat surface Grip the open mattress nipple to lift the mattress up a bit and press all air bubbles out Lower the nipple and close it Inserting the Heating Pad and Nest 1 2 3 4 Place the water mattress on a flat surface to insert the heating pad Turn the wate
8. and materials are available Please contact your local supplier Warming Capacity Fill with warm water to reduce the warming up time Normal conditions About 4 5 C per hour Room temperature about 22 C and filled with 4 5 litres of water and placed on the mattress of a baby bed and covered with the nest anda sheet Connection to mains or a 24V battery 12 V Battery About 1 5 C per hour up to set temperature minus 6 C About 0 5 C per hour up to set temperature minus 2 C About 0 3 C per hour up to set temperature Twin Mattress If not filled with warm water the AT alarm will be activated after 4 hours Restart and the temperature will be reached A naked twin mattress will not reach set temperature due to excessive heat loss Page 14 of 16 KANMED BABYWARM ER User Manual Bw 50 070 10 Safety Standards Standards EN 60 601 1 EN 60 601 1 2 EN 60 601 2 35 Protection type BF Defibrillator safe Class I CE marking Fulfils MDD 93 42 EEC MDD class IIB EC 0413 Intertech SEMKO Sweden Environmental Conditions Storage Surrounding temperatures In use 10 to 34 C Storing 40 to 70 C Humidity 10 100 condensing EMC Guidelines The BW 50 Baby Warming system should not be used adjacent to or stacked with other equipment If adjacent or stacked use is necessary the BW 50 Baby warming system should be observed to verify normal operation in the configuration in which it is used Additional EMC information can be fou
9. d lamp and especially for new blue lights that do not give any heat Cleaning and disinfecting GENERAL The user of KANMED equipment shall not use any methods for cleaning and decontamination other than those recommended by KANMED without first checking with KANMED that these methods do not harm the equipment KANMED equipment withstands all known cleaning and disinfection liquids Do not autoclave any parts Protect yourself according to hospital routines Control Unit e Remove the mains cable and the Heating Pad e Wipe off with a cloth moistened with cleaning and disinfectant liquid that you normally use for technical equipment e Always clean between patients or per your own routines Water Mattress e Add Anti Algae from day one e Clean with water and wipe off with a cloth moistened with cleaning and disinfectant liquid that you normally use for plastics e If HIV or Hepatitis is suspected cleaning can be done with much stronger agents such as ethyl alcohol 50 formaldehyde or chloramines Continued next page Page 9 of 16 KANMED BABYWARM ER User Manual Bw 50 070 10 e Note Flushing the inside using pure alcohol stronger than 50 may remove the printed instructions on the mattress e Always clean between patients or per your own routines Heating Pad e Use same method as for Water Mattress e Avoid fluids in the connector e Always clean between patients or per your own routines KANMED Baby Nest e May be machi
10. elivery The sole obligation of KANMED with respect to any such defect is limited to the repair with new or re manufactured parts or at the discretion of KANMED replacement of the equipment or refunding of the purchase price This warranty shall not apply if the product has been modified adjusted or repaired other than by KANMED or by organisations authorised by KANMED or modified adjusted or repaired not in accordance with written instructions provided by KANMED Neither shall the warranty apply if the equipment has been subject to misuse negligence or accident These warranties are made on the condition that prompt notification of a defect is given to KANMED or its authorised dealers within the warranty period KANMED shall have the sole right to determine whether a defect exists KANMED shall not in any case be liable for special or consequential damages arising from the breach of warranty breach of contract negligence or any other legal theory ps When the KANMED Baby Warmer have reached end of life it should be recycled in accordance with the EU 2002 96 EC WEEE directive if applicable Page 15 of 16 KANMED AB G rdsfogdev gen 18B SE 168 66 BROMMA Stockholm Sweden Telephone 46 8 56 48 06 30 Telefax 46 8 56 48 06 39 E Mail info KANMED se Home page www KANMED se Distributed by
11. et Height about 30 cm and min diameter 20 cm with warm water 38 C Roll the Heating Pad loosely and insert it fully in the water Slowly fill with warm water until the temperature reaches 39 5 C NOTE It will take a few minutes for the sensor in the Heating Pad to reach 39 5 C Check that the over temperature lamp is lit and that the beeper sounds at 39 5 C 1 C NOTE During this test other alarm lamps may be lit and the beeper may sound but this does not influence the test Temperature deviation alarm AT This alarm can only be activated after the selected temperature has been reached There are 2 ways of performing this test Testing at normal use and when the set temperature has been reached 1 2 3 Note actual temperature Pull out the Heating Pad from the pocket of the mattress so that temperature sensor T1 is cooled Check that the alarm lamp is lit when the temperature has dropped 1 C Testing with a water container 1 2 3 Fill a water container with 36 C water and insert the Heating Pad Start the warming and wait until the temperature lamps indicates that the set value has been reached Fill slowly with hot or cold water and note that the AT lamp is lit when the temperature has changed more than 1 C Page 12 of 16 KANMED BABYWARM ER User Manual Bw 50 070 10 Missing Water Mattress alarm H20 1 Start the unit and observe an OK self test 2 Place the Heating Pad without the Water Ma
12. exposed to sharp objects For cleaning and disinfecting see user s manual The Heating Pad must be stored flat or rolled with a diameter of at least 10 cm 4 Do not fold Page 6 of 16 KANMED BABYWARM ER User Manual Bw 50 070 10 The Water Mattress When filled to the level mark it contains about 4 5 litres of water If you plan to tilt the bed then add 2 cm of water Fill by using the filling tube Add Anti Algae every 3 months Water molecules diffuse through the material This is normal Therefore the water level should be checked regularly NOTE Do not tilt the Water Mattress if the temperature must be higher than 37 C The very sensitive over temperature circuit can alarm and switch off the warming When tilting during warming up too little water will make the over temperature alarm go off Explanation of the drawings on the Water Mattress 9 The level mark on the Water Mattress indicates standard water amount If tilting is required please add 2 cm more water 10 Place the Water Mattress in an upright position and fill it with the enclosed Filling Tube When the desired level has been reached add Anti Algae carefully through the filling hole or via the Filling Tube Follow the caution instruction on the Anti Algae package NOTE Air pressure may build while filling Interrupt filling and release air if necessary 11 Remove air bubbles Very Important Place the Water Mattress on a flat surface and lift the filling hole 5 to
13. ge failure Supply voltage mains or Stops battery has disappeared or been switched off without pressing Start Standby first Internal battery AT H20 EC Internal battery is weak or missing Will not start at start up Press and hold the Alarm button when restarting Replace battery as soon as possible Symptom Probable cause Remedy No lamp lit No supply voltage connected Connect supply cable Power switch on rear panel in Check On Off switch OFF position Control Unit fuses blown Check fuses contact technician lamp is blinking and the Supply voltage has disappeared Check supply voltage and that I acoustic alarm is on during warming the unit automatically starts when supply voltage is restored The water temperature is gt Check if some external heat d lamp is blinking 39 5 C source has influenced the unit Error in the Control Unit or the Let a technician check the unit Heating Pad Too little water during warming Add 2 cm water above the level up with tilt line Water temperature deviates Check for any external AT lamp is lit more that 1 C from influences Has the unit been selected value moved to another bed without switching it off The selected water temperature Check the bedding Is the water has not been reached after 4 mattress placed on an hours insulating surface Restart again Page 11 of 16 KANMED BABYWARMER User Manual Bw 50 070 10 H20 lamps is lit The Heating Pad is not inserted in the Water
14. ith the baby s reaction to the water temperature Overheating is often caused by covering the baby too much 37 C is a good starting temperature for slightly hypothermic babies and for babies weighing less than 1000g 36 5 C is the most common temperature for babies weighing more than 1000g As the baby s weight increases the temperature is primarily controlled by changing the amount of blankets that cover the Baby and secondly by changing the temperature in 0 5 C increments When the lightly dressed and covered baby is maintaining body temperature with a water temperature of about 35 5 36 C then the baby is most often ready for a standard cot that has no warming Maintenance 1 2 3 4 Wash the nest at maximum 90 C Preferably 60 C Dry tumble it KANMED recommends you to change the Baby Nest once a year Surface disinfect the water mattress and the heating pad Change water every 3 months and add a new bottle of anti algae See the user s manual for further maintenance instructions and periodical safety checks Page 3 of 16 KANMED BABYWARMER User Manual Bw 50 070 10 Please read this manual carefully and you will find the KANMED Baby Warmer to be easy and safe to use Intended use The intended use of the KANMED Baby Warmer is to keep newborn and premature babies normothermic KANMED Baby Warmer BW50 is designed for hospital use only It must be used according to the instructions in this manual and according
15. nd in the service manual Connection to battery If the Control Unit is to be connected to a battery 12 24 V from a vehicle etc use the Battery Cable BW 50 007 Connect the battery cable to the Battery inlet and secure it with the locker ring Connect the other end fitted with cigarette lighter plug to the vehicles cigarette lighter socket or similar outlet If the lighter plug has to be changed to another model or if the power is taken from batteries directly then note that the white cable is and the brown is minus Modifications Any modifications on the control unit heating pad and water mattress will void KANMED s responsibilities totally and are not allowed without the written consent of KANMED Expected lifetimes Control unit BW 50 Kanmed warrants a safe lifetime for Control unit BW 50 of 10 years from first day of use This is under the condition that the unit has been serviced according to the user and or service manual and that the unit has not been modified or changed in any way or for any reason Heating Pad Heating Pads are consumable products and the expected lifetime is one to two years depending how they are handled and how often they are used KANMED warrants the purchaser that the Control Unit BW 50 Heating Pad BW 50 002 are free from defects in material and workmanship for a period of 12 month from the date of delivery The KANMED Baby Nest and associated parts are warranted to be free of defects at the time of d
16. ne washed at temperatures up to 60 C e Centrifuge at medium to low speed e Always dry tumble e If needed the nest can withstand 90 degree washing but this may shorten the lifetime e Check for damages after washing e Always wash between patients or per your own routines Periodical exchanges Water in Water Mattress e Every 3 months e Do not forget to add a whole bottle of KANMED anti algae The Water Mattress The Water Mattress should be changed at least every third year to avoid leakages KANMED Baby Nest The Baby Nest is a consumable The KANMED Baby Nest containing filling material must be changed as soon as it shows signs of damage or wear at least after one year of use Periodical Checks Recommended checks To be done by Interval Water Mattress and water level Heating Pad The user Every time the bed is Baby Nest are they clean and undamaged made Cables and connectors are they clean and The user At each start undamaged Self test at start The user At each start Check of safety systems as per chapter 10 Technician or user Every year Electronic safety test Technician Every year Temperature check as below Technician or user Every year or when in doubt Replacement of the internal 1 5V battery Technician Every year LR6 AA type Temperature Check To perform the temperature check a precision thermometer preferably with a skin sensor is needed e Make up the bed as for normal use and place the skin probe in
17. r mattress upside down and insert the Heating Pad in the pocket with its printed text towards the water Turn the water mattress over again Insert the water mattress with heating pad into the nest pocket Use the opening in the head end of the nest to assist in fitting the Nest to the water mattress eee the bed aa Ensure that the bed has holes in the bottom Place the Baby Warmer on the cot mattress Place the Baby Warmer in the KANMED Baby Bed or any other suitable bed Protect the Nest with a sheet that is soft but not too thick Connecting the Control unit 1 2 3 4 Connect the Heating Pad at the back of the Control Unit Don t over tighten Connect the power cable at the back of the Control Unit and switch it on Hang the Control Unit in a safe place where it can be seen Press the start button on the front panel and observe that it starts at 37 C after a short self test Placing the baby 1 2 3 4 Only when the desired temperature is reached you can place the baby in the nest Position the lightly dressed baby diaper long arm T shirt bare legs and a cap on very small ones on its back in the nest Adjust the nest size by pulling the string Hide the cord under the mattress Cover the baby with suitable cover such as 1 3 layers of cotton blankets Temperature setting 1 2 3 4 5 All babies are individuals and their temperature must be controlled frequently until you are familiar w
18. refully Please be aware that the acoustic alarm has a sound level of 55dBA adapted for use in silent environments Check each time the unit is started that it performs the self test as described in section 10 If the self test is not performing as described leave the unit to a qualified technician Don t fold or bend the Heating Pad sharply Only use Heating Pad BW 50 002 together with control unit BW 50 Don t pull the Heating Pad cable or use it for carrying the Heating Pad Use only in hospitals and by qualified personnel Please be aware that use of HF surgical instruments endocardial catheters or similar devices may interfere with the BW 50 and may require special precautions regarding potential equalization etc Safety Instructions for KANMED Baby Warmer 50W Always fill the Water Mattress to the required level before the unit is brought into use Preferably fill with lukewarm water at around 35 C Replace the Water Mattress every 3 years Always place the Heating Pad inside the pocket of the Water Mattress before you switch on the unit Make sure that the text side of the Heating Pad is turned towards the Water Mattress Make sure that there are at least 2 holes in the bottom of the bed If feasible the connection cable to the Heating Pad can be thread through a suitably placed hole Always place the baby with its head towards the closed semicircular part of the KANMED Baby Nest Make sure that the adjusting string is placed out
19. rical fields Control Unit Mains power 220 240 VAC or 110 120 VAC Battery power 12 24 V DC Limited warming capacity at 12 V DC Frequency 50 60 Hz Power consumption Max 65VA Temperatures available 34 C 38 C in steps of 0 5 C Accuracy 0 5 C Resolution 0 5 C Auditory Alarm 55 dBA Sound level Indication of temperatures LED 35 37 C are green 34 34 5 37 5 and 38 C are yellow and alarms lt 34 gt 38 C are red alarms Over temperature alarm At a water temperature of 39 5 1 C Dimensions and Weight Length 210 mm With 165 mm Height 120 mm Weight about 3 kg Fuses Fi F2 220 240 VAC T1A L250V 110 120 VAC T 2A L250V Mode of use Designed for continuous use Water protection Drip proof when installed according to section 2 Internal Battery Alkaline 1 5V size LR6 AA Only for power failure alarm Water Mattress Dimensions and Weight Length 600 mm With 270 mm Height 30 mm Other sizes might be available Please contact your local supplier Weight about 0 5 kg Material PVC Anti Algae recommended KANMED Bottle 119 ml fluid Poly Oxyethylene dimethylimino ethylene dimethyliminio ethelyenedichloride 10 Inert ingredients 90 KANMED Baby Nest Dimensions Length 650 mm Width 450 mm Height 50 mm flattened Material Cover High quality cotton and polyester Filling of collar Polyester fibre Always tumble dry Washing Recommended temperature 60 C Can tolerate 90 C but may shorten lifetime Other sizes
20. side the Baby Nest to prevent it from interfering with the baby Check the water temperature regularly Check the temperature of the baby regularly Continue to use appropriate monitoring of vital signs NOTE A cold Water Mattress or a Mattress which is cooling down due to the heating being switched off will decrease the temperature of the baby Likewise a too warm Water Mattress can give the baby a fever Check the integrity of the KANMED Baby Nest so that the filling material does not leak out Replace the nest after one year of use When the unit is delivered it is factory clean but not sterilised Please clean according to your standard hospital routines Please note that the control unit BW 50 shall be placed horizontally on a flat surface or mounted with the front end up at a maximum angle of 45 degrees in order to fulfil the IPX1 water protection requirements The KANMED Baby Warmer consists of 4 major components Control Unit KANMED Baby Nest Heating Pad Water Mattress Page 5 of 16 KANMED BABYWARM ER User Manual Bw 50 070 10 Control Unit The Control Unit can be connected to all existing mains power supply voltages observe fuse change and frequencies or be battery powered from 12 24 Volts See technical section The handle is designed so that the control unit can be safely hung on the edge of the bed or on the bed frame Front Panel 1 2 Button for temperature selection 3 Indicators selectable
21. the centre on top of the Water Mattress Cover the probe with an insulating material e Start the unit and wait until the Control Unit indicates that set temperature is reached e Check that the precision thermometer and the Control Unit displays the same temperature allowed difference 0 5 C Page 10 of 16 KANMED BABYWARM ER User Manual Bw 50 070 10 In case of an alarm the associated red lamp will be lit and the beeper will sound intermittently Only the AT alarm can be silenced for 10 minutes by pressing the alarm button All other alarms require some action In most alarm conditions the warming will stop This can be seen by the fact that no temperature lamp is lit In such case the only way to silence the alarm is to press the Start Standby knob Alarm Symbol Reason Warming Over temperature Water temperature gt 39 5 C Will stop Temperature deviation AT The water temperature deviates Continues for 10 more than 1 C min NOTE This alarm is not activated until set temperature is reached or 4 hours after start whichever happens first The alarm can be silenced for 10 min but if after that the temperature still differs more than 1 C the warming will stop No Water Mattress H0 The heating pad is not inserted into Stops the water mattress or too little water Pad fault Heating pad is faulty or not Will not start or connected stops Control Unit fault Technical failure Will not start or I stops Supply volta
22. the ordinary mattress of a baby cot or any other surface that is heat insulating Always leave the unit switched on even in the storage room so that the water mattress is warm and ready Delivery Wards e Use it for children that for different reasons have lost heat after the delivery e Low birth weight or premature babies that do not need all the resources of an intensive care department can thanks to the KANMED Baby Warmer be kept with the mother in the ward e In rooms with low temperatures Transport of babies inside the hospital If the child is normally covered and in a standard cot the water temperature will only drop about 1 5 C per hour when the power is disconnected Page 8 of 16 KANMED BABYWARM ER User Manual Bw 50 070 10 When transporting in an ambulance ground or air The KANMED Baby Warmer can be powered from a 12 24 Volt battery During transport it will keep the baby warm and provide a soft chock absorbing support NOTE When powering with 12V battery the warming capacity is reduced see technical section Note that local restrictions and rules apply for transport of patients In Maternity Wards it allows more children to stay with their mother and will save costs In between babies that are babies between 2000 and 2500 gram born around pregnancy week 35 38 are often not capable of maintaining a normal body temperature during their first days after birth KANMED Baby Warmer keeps them at normal temperat
23. to established clinical routines and by qualified personnel Explanation of symbols AN AA Check users manual 4 Protection grade BF Defibrillator safe Key to select temperatures outside 35 37 C Called Temp lock in text q Over temperature alarm H20 Indicates that the Water Mattress is missing or in the wrong position TEOL onene Certified by SEMKO CEo413 according to EN 60 601 1 A A EN 60 601 1 2 ore EN 60 601 2 35 Technical failure in the control unit E Can be centrifuged at low speed No dry cleaning START STAND BY I al on Equi potential connector KBW 50 Alternating Current e 2 wie Ep IPX 1 Drip proof Control unit BW 50 ETL approved for Canada US Note only l labelled on units sold to Canada USA c US Page 4 of 16 Risk of explosion if used in presence of inflammable gasses Temperature selection Button Alarm button To silence AT alarm for 10 minutes Indicates water temperature deviation more than 1 C from selected value Indicates Heating Pad fault Fullfills MDD 93 42 EEC EC Type examination certificate issued by a Notified Body 0413 Intertech SEMKO Sweden Machine washable at maximum 60 C Tumble dry On Off Battery Direct current Abbreviation for KANMED Baby Warmer 50W IPX 7 Water proof Heating Pad KANMED BABYWARM ER User Manual Bw 50 070 10 General Safety instructions Read this user s manual ca
24. ttress on a flat surface 3 Wait 5 to 7 minutes and check that the H20 alarm lamp is lit NOTE The Heating pad must be at room temperature before starting this test Heating Pad fault alarm EC For this test the heating pad is not connected to the control unit Start the warming and check that the Heating Pad symbol and the Pad lamp are lit after about 3 sec and that the beeper sounds Supply voltage failure alarm For this test the unit must be assembled completely with Water Mattress and Heating Pad 1 Start the warming 2 After about one minute select a temperature different from 37 C and make a note of it 3 Wait about 2 minutes and then disconnect the supply voltage by using the mains switch or pulling out the mains plug 4 Check that the temperature lamp is off and that the Control unit lamp starts to blink and that the acoustic alarm beeps intermittently for at least 10 minutes 5 Switch on supply voltage again and check that the self test is performed OK and that the warming starts at the value selected before supply voltage interruption Internal 1 5 V battery test This test may only be done by a qualified technician During this test the heating pad must be connected and the internal 1 5 Volt battery removed from its holder by opening the Control Unit 1 Press start and check that the red lamps for AT H20 and EC blinks Press Start standby 2 Make a new start but keep the alarm button pressed continuously until the self test
25. ure and allows them to stay with their mothers Uneasy stressed and screaming babies can often find a soothing and relaxing environment on the warm water mattress thereby relieving the staff or mother Neonatal intensive care departments KANMED Baby Warmer can be used to reduce the time the baby needs to spend in an incubator KANMED Baby Warmer can replace the incubator when the baby is mostly in need of the warming Vital signs monitoring can easily be continued in the KANMED Baby Warmer and the KANMED Baby Bed The KANMED Baby Warmer can also be used inside an incubator to help obtain correct body temperature especially in older single wall units This has not been tested by KANMED and is the sole responsibility of the hospital NOTE The function and temperature regulation of the KANMED Baby Warmer is not influenced by the incubator Try it for children in need of a soft warm support for instance children suffering from hydrocephalus fractures or headaches after delivery with a forceps or a suction device colicky pains etc NIDCAP Developmental Care and Kangaroo care In these treatment forms the sleeping and rest as well as positioning of the baby plays an essential role The warm soft water mattress resembles the warmth of a mothers skin making the KANMED Baby Warmer the ideal tool to ensure quality sleep Kangaroo care is encouraged in open systems Photo therapy KANMED Baby Warmer is very suited for Photo therapy by using an overhea
Download Pdf Manuals
Related Search