SPDU2000 User manual
Contents
1. por EE ee SPDU2000 User manual 1 PRODUCT INTRODUCTION SPDU2000 Applied to 482 6mm 19 standard cabinet amp nonstandard cabinet horizontal or vertical installed 1U SPDU2000 Multi outlets sequential power on and power off To avoid in rushes at start up and turn off which can cause overloaded circuits and dropped loads To avoid the instantaneous power resulting from the current shock protection device malfunction and the interference between the network equipment of pollution SPDU2000 8 way output modules could assemble different standards of sockets SPDU2000 Accord with the regulations of European Union ROHS directive 110 220VAC Rated voltage Meeting requirements from different countries and regions 2 Characteristics 2 1 Sequential power on and power off function Choose and setup the outlets power on or power off sequentially through option switch to avoid in rushes at start up and turn off which can cause overloaded circuits and dropped loads the instantaneous power resulting from the current shock protection device malfunction and the interference between the network equipment of pollution 2 2 Sequential power on and power off in group function Through the option switch user can freely configure or choose the power on off sequence for each group outlets 2 3 Power delay time adjusting function Through the option switch user can flexibility adjust and control the power delay time of multi equipments 2 4 Dyn2. you want start it again you can press start stop button for 3 seconds to enter the start program the run indicator flashes frequently outlets will sequential power on 4 3 Refresh after power on effective only in on situation when you need to modify the state of output equipment and power delay after power on please press reset button 4 4 Grouping Press start stop button to start the power when the run indicator flashes frequently about 0 25s t Loosen the start stop button to enter the grouping program When you need to select grouping and make the selected outlets be ON press reset button the run indicator flashes frequently for one second indicate grouping is successful If the run indicator flashes frequently intermittently it fails in grouping If you want to reset you should follow the above way to operate again You can stop the power button after grouping if you don t want to continue Press reset button when you enter the grouping program the former grouping record will be cleared away please attention when grouping should be over one way you can t set again 4 5 Reset the default setting of leaving factory Enter the grouping program and make all the buttons off press reset once again and turn off the power button then the program is finished 4 6 Configure the power delay time You can set the power delay time between O and 15 seconds When option
3. 1 is on it means 1 second power delay When option 21 is on it means 2 seconds power delay When option 3 is on it means 4 seconds power delay When option 4 is on it means 8 seconds power delay When all options are on it means 15 seconds power delay When all options are off it means 0 second power delay 4 7 Quickly switch off when in trouble When in urgent trouble press on off switch button to stop power at once po EE ee 5 Technology Parameters Capability Main description Rated voltage 110 250VAC 50 60HZ Input Cable specification 3x 2 5mm x3M 3x 4 0 mm x3M Plug with the cable Different standards plug and IEC60309 plug Outlet standard IEC320 C13 IEC60906 Output Rated power 3 5 digit digital AC ampere meter Display 8 way Green LED indicator Avoiding mistaken operation warping button Output option switch 8 way DIP button Control Product size Working temperature O C 55 C Environment Relative Humidity 10 90
4. 5 67 6 LLLI Start Stop 1 POWRE Light when SPDU2000 connect to AC power supply 2 RUN Flash when SPDU2000 operate normally 3 Bus A Indicators 1 8 Light when the corresponding outlet power on 4 Reset Press RESET button to refresh outlets without affecting ON OFF state of SPDU2000 Time delay setting button Configure the power delay time 0 15s Option switch Set up on off state of outlets for corresponding group Circuit Breaker Overload protector 8 Start Stop button Effect after press for 3 seconds Master power switch Master switch for PDU 0 Ammeter Display the total current of this unit it r i a F a Ee Ar ee aar LLL LL Chipi Maime The figure below is SPDU2000 control function module po EE A 4 Operation of SPDU control function module 4 1 Power start When SPDU2000 connects the power supply set up the required outlets and power delay time Then switch on the run indicator flashes frequently and these outlets will sequential start on After finished the start the run indicator flashes slowly about 0 5s t 4 2 Start stop after power start Please press start stop button for 3 seconds after power start the run indicator flashes frequently after this operation valid And then loosen the button to enter the stop program outlets power down sequential After finish power down the run indicator flashes slowly about 1s t If
5. amic adjusting controlling function Users could adjust control turn on off state for each outlet group without affecting the normal operation of this unit 2 5 Reset refresh keeping function Reliable reset button can refresh the operating commands 2 6 Start stop power delay function The flexible power delay start button can carry out the commands safely and correctly 2 7 Short circuit overload automatic break function Overload protector can break the circuit when the equipment overload or short circuit to protect equipment from damage 2 8 Avoiding mistake quickly switch off function Master switch prevent the mistaken operation in special conditions can quickly switch off to stop power supply 2 9 Digital ammeter 3 5digit AC ammeter can be true and accurate to show the load current numerical value and changes 2 10 Operating state display function LED indicators can timely show the start stop and run state of this unit clearly 2 11 Output state display function The LED indicators can clearly and directly show the operating state of each PDU units 2 12 Avoiding the plug escaping from output sockets function The output units are the avoiding escaping IEC320 C13 sockets which can make the plug more reliable and not easy to fall off when it plugs into the socket SPDU2000 User manual 2006 VO 3 Control module Description SPDU2000 control function module iN iL d 4 Detay Option Power Run Ressel Ciawi Breskar 412346
Download Pdf Manuals
Related Search