ETH1000-MKII User manual
Contents
1. IR cards etc Flashlink features All the laser module cards in the Flashlink ETH1000 MKII range are Class 1 laser ETH1000 MKIIs according to IEC 825 1 1993 and class I according to 21 CFR 1040 10 when used in normal operation More details can be found in the user manual for the FR 2RU 10 2 frame Maximum output power 5 mW Operating wavelengths gt 1270 nm OPEN c DUCT REF FDA CFR Ch 1 4 1 97 Ed 1040 10 1 Max power is for safety analysis only and does not represent device performance nevion com 12 ETH1000 MKII Rev A General environmental requirements for Nevion equipment 1 The equipment will meet the guaranteed performance specification under the following environmental conditions Operating room temperature range 0 C to 40 C Operating relative humidity range lt 90 non condensing 2 The equipment will operate without damage under the following environmental conditions Temperature range 10 to 55 C Relative humidity range lt 95 non condensing nevion com 13 ETH1000 MKII Rev A Product Warranty The warranty terms and conditions for the product s covered by this manual follow the General Sales Conditions by Nevion which are available on the company web site www nevion com nevion com 14 ETH1000 MKII Rev A Appendix Materials declaration and recycling information A 1 Materials declaration For product sold into China after 1st March 2007 we comp2. KII Rev A 5 2 GPI Alarm Module status outputs These outputs can be used for wiring up alarms for third party control systems The GPI outputs are open collector outputs sinking to ground when an alarm is triggered The GPI connector is shown in figure below GPI pinning Signal Name Pin Mode General error status for the Pin 1 Open Collector module Electrical Maximums for GPI outputs Max current 100mA Max voltage 30V Brown Pair4 gt Green Blue Pair 3 Pair 1 Orange Pair 2 Figure 6 nevion com 11 ETH1000 MKII Rev A 6 Laser safety precautions Guidelines to limit hazards from laser exposure All the available EO units in the Flashlink range include a laser Therefore this note on laser safety should be read thoroughly The lasers emit light at 1310 nm or 1550 nm This means that the human eye cannot see the beam and the blink reflex cannot protect the eye The human eye can see light between 400 nm to 700 nm A laser beam can be harmful to the human eye depending on laser power and exposure time therefore Be careful when connecting disconnecting fibre pigtails ends Never look directly into the pigtail of the laser fibre Never use microscopes magnifying glasses or eye loupes to look into a fibre end Use laser safety goggles blocking light at 1310 nm and at 1550 nm Instruments exist to verify light output power Power meters
3. abeled to show their material content Depending on the date of manufacture this product may contain lead in solder Some circuit boards may contain battery backed memory devices nevion com 15
4. ck command gt lt set state gt lt set state gt act inact thru 3 2 1 5 Ethernet port lt identifier gt ethp lt status gt dis en cd ncd 10 100 1000 man auto full half auto mdi mdix auto mas sla auto lt block command gt delen lt speed mode gt lt speed mode gt speed 10 100 1000 auto 3 2 1 6 Misc lt identifier gt misc lt status gt prog fin ovr nevion com 7 ETH1000 MKII Rev A 4 Connector module The ETH1000 MKII has a dedicated connector module ETH1000 C1 This module is mounted at the rear of the sub rack The module is shown in the figure below ETH 1800NC OPT TX GPI OPT RX 10 100 1000Base T Figure 4 4 1 Mounting the connector module The details of how the connector module is mounted is found in the user manual for the sub rack frame FR 2RU 10 2 This manual is also available from our web site http www nevion com nevion com 8 ETH1000 MKII 4 2 Terminal format support The different input and output ports on ETH1000 MKII can support a number of formats The table below shows the input and output signals on the back plane Terminal format support Rev A Terminal Function Supported Format Mode OPT RX Optical input 1000Base X Input OPT TX Optical output 1000Base X Outpu
5. e Eeer 10 5 2 GPI Alarm Module status outputs EEN 11 6 Laser safety precautions EEN 12 General environmental requirements for Nevion equipment 000000000onneneeeeeeaa 13 Prod ct Warranty ae 14 Appendix A Materials declaration and recycling Imtormaton 15 A 1 Materials declaration 15 A 2 Recycling Ria eu En EE 15 nevion com 3 ETH1000 MKII Rev A 1 Product overview The Flashlink ETH1000 MKII is a 10 100 1000Base T to 1000Base X media converter module The module converts a 10 100 1000Mbps Ethernet signal on copper to 1000Mbps optical on fibre suitable for medium haul applications The module has one electrical Ethernet port and one optical fibre transceiver port receiver fibre connector and transmit fibre connector The speed on the electrical connector is dependent of the DIP switch setting or GYDA control Speed will upon link connection automatically be set at the highest possible speed User can independently enable or disable 10Mbps 100Mbps or 1000Mbps The fibre link can be used in one or two fibre installations or occupy two wavelengths in a WDM or CWDM installation _Optical transmitter_ Optical o gt output 10 100 1000Mbps Physical Twisted pair ech ane Optical reciver Ethernet Optical H i input Status LED Microcontroller e a Remote DIP switch control Figure 1 Wwnevion KN MOD APC SE O Figure 2 nevion com 4 ETH1000 MKII Rev A 2 Specif
6. ications 2 1 Optical Characteristics Optical input Transmission circuit fibre 9 125um Single Mode Sensitivity Better than 25dBm Optical wavelength 1200nm 1610nm Detector damage threshold gt 1dBm Max input power 0dBm Connector SC UPC Optical Output Transmission circuit fiber 9 125um Single mode Light source F P DFB laser Optical power 13T 5 dBm 3 to 12dBm typ 5dBm CWDM 0dBm 1dBm Optical centre wavelength 1310nm or CWDM 2 2 Ethernet 10BaseT 100BaseTx 1000BaseT on RJ 45 connectors Compliant with IEEE 802 3 IEEE 802 3u IEEE 802 3ab and IEEE 802 3z Auto speed sensing and MDI MDI X 2 3 General Power 5V DC 2 9W Control Control system for access to setup and module status with BITE Built In Test Equipment nevion com 5 ETH1000 MKII Rev A 3 Configuration ETH1000 MKII can be configured by DIP or from Flashlink Multicon GYDA 3 1 DIP control The tables below explain the functionality of the dip switches 1 Mbit ek 1 Mbit 0 1Gbit Autoneg Hu Gyda DIP wd Figure 3 Description Enable 10Base T Enable 100Base T Enable 1000Base T Auto negotiation on 1000Base X Reserved Reserved EE ae Reserved 8 GYDA override DIP When DIP switch 1 2 and 3 are all on or off speed is set to auto DIP switch 1 enables disables 10Base T electrical connection DIP switch 2 enables disables 100Base T electrical connection DIP switch 3 enables disables 1000Base T electrica
7. l connection DIP switch 4 enables disables auto negotiation on the optical connection 1000Base X When connecting ETH1000 MKII to ETH1000MC auto negotiation must be disabled Using two ETH1000 MKIIs or ETH1000 MKII together with ETH1000 D these DIPs must be in the same position on both cards Also this dip must be on to be able to communicate with other vendors Ethernet switches Dip 5 6 and 7 are reserved Dip 8 sets if Multicon Gyda is able to configure or not When Multicon Gyda override is set the actual setting can be read by using the info command se Multicon Gyda user manual for details 3 2 Multicon Gyda control Latest configuration from Multicon Gyda is stored locally on the card This prevents configuration loss during power recycling The card supports Flashlink protocol v4 0 nevion com 6 ETH1000 MKII Rev A 3 2 1 Block descriptions Supported block command 3 2 1 1 Laser lt identifier gt Isr lt status gt C lt wavelength gt nm lt power gt dBm Dono ok fail lt block command gt lt operation gt lt operation gt on off 3 2 1 2 PIN lt identifier gt pin lt status gt cd ncd 3 2 1 3 Voltage lt identifier gt pwr lt status gt lt nominal voltage gt Vnom lt voltage gt 3 2 1 4 General output lt identifier gt gpi lt status gt out act inact thru id lt GPI identifier gt lt blo
8. ly with the Administrative Measure on the Control of Pollution by Electronic Information Products In the first stage of this legislation content of six hazardous materials has to be declared The table below shows the required information Toxic or hazardous substances and elements REH Si SS S ASME SRK SS FR Part Name Lead Mercury Cadmium Hexavalent Polybrominated Polybrominated Pb Hg Cd Chromium biphenyls diphenyl ethers Cr VI PBB PBDE ETH1000 MKII O O O O O O O Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this part is below the limit requirement in SJ T11363 2006 X Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used for this part is above the limit requirement in SJ T11363 2006 This is indicated by the product marking A 2 Recycling information Nevion provides assistance to customers and recyclers through our web site http www nevion com Please contact Nevion s Customer Support for assistance with recycling if this site does not show the information you require Where it is not possible to return the product to Nevion or its agents for recycling the following general information may be of assistance Before attempting disassembly ensure the product is completely disconnected from power and signal connections All major parts are marked or l
9. nevien ETH1000 MKII Gigabit Ethernet Media Converter User manual Rev A ETH1000 MKII Rev A Nevion Support Nevion Europe Nevion USA 1600 Emerson Avenue Oxnard CA 93033 USA Toll free North America 866 515 0811 Outside North America 1 805 247 8560 P O Box 1020 3204 Sandefjord Norway Support phone 1 47 33 48 99 97 Support phone 2 47 90 60 99 99 E mail support nevion com See http www nevion com support for service hours for customer support globally Revision history Current revision of this document is the uppermost in the table below Rev Repl Date Sign Change description A 1 2013 10 11 MS Updated template Corrected LED status information 1 0 2011 11 29 AJM Changed wording in chapter 3 1 0 2011 06 30 GMW MS First version nevion com 2 ETH1000 MKII Rev A Contents ELE 2 TPP OCC HOW OT NNN SS 4 2 SPEMICAONS eieiei 5 21 e eier ee 5 2 2Eth emet aa 2 EE EE 5 EE EE 5 3 Configuratio Mes iinan aa aa eaaa AEA A Aa AE AEA AE ARE 6 31 IDR COMMON Pec AE E A E E E oh oe a ca ard E E AE EE AN 6 3 2 Multicon Gyda gGonttol EENEG eine dalek saab tes a cee EEE EE aa 6 3 2 1 Block E el e EE 7 4 Connector Inte e EUR 8 4 1 Mounting the connector Module L m miare man ans andy ceased ed ee iets mean eee 8 42 Terminal format support EE 9 elei SES eee ENE bee 10 5 1 Front panel Status monitoring 2esc2ltesneceds cose ese ssene dradd k
10. t 1000Base T Electrical input 10 100 1000Base T In output GPI ALARM Open Collector Wired alarms OG Output Alarms nevion com 9 ETH1000 MKII Rev A 5 Module status The status of the module can be monitored in three ways 1 GYDA SC System Controller optional 2 GPI at the rear of the sub rack 3 LED s at the front of the sub rack Of these three the GPI and the LEDs are mounted on the module itself whereas the GYDA System Controller is a separate module giving detailed information on the card status The functions of the GPI and the LEDs are described in sections 5 2 and 5 1 GYDA SC is described in a separate user manual 5 1 Front panel Status monitoring The status of the module can be easily monitored visually by the LEDs at the front of the module The LEDs are visible through the front panel as shown in the figure below Figure 5 Front panel indicators for the ETH1000 MKII 6 STATUS ol LOS ol LINK O ACT ETH1000 MKII has 4 LEDs each showing a status corresponding to the GPI pinning Diode State Red LED Green LED Orange LED No light Status Module is faulty Module is OK Laser off Module has no or module is Module power is power initializing OK LOS No optical signal Optical signal Module has no power LINK N A 1000Base T link 10 100 Base T No link link ACT Ethernet traffic No Ethernet traffic nevion com 10 ETH1000 M
Download Pdf Manuals
Related Search