HDMI Extender over Ethernet Operating instructions
Contents
1. the power LED for the extender is red and the status LED becomes green Step 3 please Ping the connected device through the sequence on computer Start Run input CMD input ping 192 168 168 55 for TX or input ping 192 168 168 56 for RX you will receive the reply if the connection is established Step 4 Login in IE 192 168 168 55 default IP for TX or 192 168 168 56 default IP for RX You can setup IP address subnet mask gateway and MAC address for the IX and RX Please set IP address for each TX and each RX IP 192 168 168 XX XX 1 255 all IP address for TX and RX must be different Please set MAC address for TX and RX MAC 00 0b 78 XX XX XX XX 01 FF The MAC address for each TX and each RX must be different Step 5 After click Apply button the green LED light on the device will go out you have successfully set IP address for TX and RX now Note if you need to restore the device to it s factory default settings please power on the device the red light becomes lighting waiting about 10 seconds the green LED light starts working at this time to press the reset button about 5 10 seconds then the green light will go out you have successfully restored IP address to factory IP address now Operating Instructions PRODUCT SERVICE 1 Damage requiring service The unit should be serviced by qualified service personnel if a The DC power supply cord or AC adaptor has been damaged2. RJ45 port of Transmitter unit and RJ45 port of Receiver unit 4 Connect 5V DC power supplies to both Transmitter unit and Receiver unit 5 Power on the output device first and the source second Important Please make sure power on the transmitter and receiver first then power on the source DVO OR STB or S S 7 tel HOMI cabi 3 amp 0 b ire 3 A Joan i Catde cable i i J i 4 f NS IR RX c cable Transmitter Receiver Operating Instructions Point to multicast network configuration 1 Connect one HDMI Cable between the HDMI output port of source device and the HDMI input port of Transmitter unit 1 Connect one CAT5e or better cable between the RJ45 port of transmitter and input port of Gigabit Ethernet switch hub 3 Connect one CATSe or better cable between the output port of each Gigabit Ethernet switch hub and RJ45 port of Receiver unit 5 Power on the output device first and then the source device 6 If DIP switch at the transmitter is set up Group ID 0001 then DIP switch at each receiver should be set up as same as the transmitter Group ID 0001 Important Please make sure power on the transmitter and receiver first then power on the source OVD CA GTE _ j lia i a age ghi GIGA POE WEB SMART SWITCH a Gatfie Cable C Fb99 RX SxX FP22 RX SX EP22 RX S FP 9 RY E 4 i Tal e i eF A o a PN
3. a m i If EFA Far IPF HH Gee 0 w p 0 cs z k A DOVE ef ETEA ere ee ee Modify the TX and all RX for a different IP amp MAC address in LAN local area network to avoid conflict 6 Operating Instructions Multipoint to multipoint network configuration 1 Connect one HDMI Cable between the HDMI output port of source device and the HDMI input port of Transmitter unit 2 Connect one HDMI Cable between the HDMI input port of display and the HDMI output port of Receiver unit 3 Connect one CAT Se or better cable between the RJ45 of each Transmitter unit and RJ45 port of Gigabit Ethernet switch hub 4 Connect one CAT5e or better cable between each RJ45 port of Gigabit Ethernet switch hub to RJ45 port of Receiver unit User can select source channel by setting up dip switch on each transmitter unit And select display devices for Receiver units via one remote control 5 Use DIP switch to select sources Important Please make sure power on the transmitter and receiver first then power on the source How to use DIP switch 1 Use 4 bit DIP switch to select 16 group ID such as 0001 0010 0101 etc 2 change group ID easily to select the sources 3 For example when the connection is source DVD1 TX TX1 Gigabit Switch RX RX1 TV1 source DVD2 TX TX2 Gigabit Switch RX RX2 TV2 source DVD3 TX TX3 Gigabit Switch RX RX3 TV3 The group ID of
4. CH OF THIS WARRNTY As examples this excludes damages for lost time cost of having someone remove or re install an installed unit if applicable travel to and from the service loss of or damage to media or images data or other recorded content The items listed are not exclusive but are for illustration only 3 PARTS AND SERVICE WHICH ARE NOT COVERED BY THIS LIMITED WARRANTY ARE YOUR RESPONSIBILITY 11
5. Operating Instructions HDMI Extender over Ethernet Operating instructions Operating Instructions HDMI Extender over Ethernet Operating Instructions og hal aC ie 5ta AG i Ha a AGE t t F f HAm MT HDMI Over IP HDMI Over IP Transmitter Receiver Gefauit t TTEA Deteut EEF Ethernet EE T 1 Ethernet Dear Customer Thank you for purchasing this product For optimum performance and safety please read these instructions carefully before connecting operating or adjusting this product Please keep this manual for future reference FEATURES Flexible and scalable HDMI 1080p High Quality Video Broadcasting with Gigabit Ethernet LAN Extends 1080p HDMI signals up to 120m over a single UTP Cat5e 6 cable Multicasting and broadcasting architecture adding more displays without adding LAN bandwidth loading support Point to Point Point to Many and Many to Many network configuration Dual power input 802 3af compliant POE amp DCSV With POE function no need power adapter for TX amp RX when connecting with POE Switch Up to 16 transmitters and more than 200 receivers in a single system With IR Control function it allows you control back the source at the end of destination Built in DIP switch to change Group ID and with multiple remote control ways Support IGMP v 1 amp v 2 address Support cascading Ethernet Switches up to 3 layers NOTICE Our co
6. al connection 8 HDMI input 4 DIP switch IR TX port 6 Reset button 7 Power input port 8 Ethernet port 4 bits DIP Switch Use 4bits DIP switch to select 16 groups ID such as 0001 0010 0101 etc Default TX unicast IP address is 192 168 168 55 it can be configured from webpage TX Group IP address 239 168 168 xx xx is the value of bits 2 0 3 Operating Instructions Receiver Panel m d MAG WIH ae HI JaEaH ASO enes 4 Mimi HDMI Over IP Default mii none 1 Ethernet Indicator of power input DIP switch 7 Power input port 4 bits DIP Switch 3 HDMI Output 6 Reset button 2 Status of signal connection S IR RX port 8 Ethernet port Use 4bits DIP switch to select 16 group ID such as 0001 0010 0101 etc Default RX unicast IP address is 192 168 168 56 it can be configured from webpage RX Group IP address 239 168 168 XXX XXX is the value of bits 2 0 4 Operating Instructions User should configure the DIP switch within 10 seconds firmware should reset the system 20 second after detecting the first change of DIP switch and latch the new DIP switch value after reset Point to point configuration 1 Connect one HDMI Cable between the HDMI output port of source device and the HDMI input port of Transmitter unit 2 Connect one HDMI Cable between the HDMI input port of display and the HDMI output port of Receiver unit 3 Connect one UTP Cathe or better cables between the
7. b Objects or liquids have gotten into the unit c The unit has been exposed to rain d The unit does not operate normally or exhibits a marked change in performance e The unit has been dropped or the cabinet damaged 2 Servicing Personnel Do not attempt to service the unit beyond that described in these operating instructions Refer all other servicing to authorized servicing personnel 3 Replacement parts When parts need replacing ensure the servicer uses parts specified by the manufacturer or parts that have the same characteristics as the original parts Unauthorized substitutes may result in fire electric shock or other hazards A Safety check After repairs or service ask the servicer to perform safety checks to confirm that the unit is in proper working condition WARRANTY lf your product does not work properly because of a defect in materials or workmanship our Company referred to as the warrantor will for the length of the period indicated as below Parts 2 Year Labor 90 Days which starts with the date of original purchase Limited Warranty period at its option either a repair your product with new or refurbished parts or b replace it with a new of a refurbished product The decision to repair or replace will be made by the warrantor During the Labor Limited Warranty period there will be no charge for labor During the Parts warranty period there will be no charge for parts You must mail in
8. mpany reserve the right to make changes in the hardware packaging and any accompanying documentation without prior written notice Operating Instructions TABLE OF CONTENTS specifications Package Contents Panel Descriptions Connecting and Operating Typical Application Maintenance Product service Warranty SPECIFICATIONS Operating Temperature Range 5 to 35 C 23 to 95 C 5 to 90 RH No Condensation Transmission Distance 1080P 60Hz1 20m Maximum over single CAT5E 6 24AWG Solid Power consumption OV 1A DC 802 3af POE i Power consumption Max 4W Dimension LxWxH L94xW93 5xH24 6mm IR frequency range 38 56kHZ Net Weight Receiver 255g Iransmitter 2559g Default IP address 192 168 168 55 MAC address 00 0b 78 00 60 01 Group IP address 239 168 168 xx xx is the value of bits 2 0 Default IP address 192 168 168 56 MAC address 00 0b 78 00 60 02 Note1 Specifications are subject to change without notice Mass and dimensions are approximate Note2 IP and MAC address must be different for one TX to many RX or many TX to many RX configuration PACKING CONTENTS 1 Main Unit Transmitter amp Receiver HDMI Extender 2 Power adapter DC 5V 1A x2PCS 3 IR TX cable amp IR RX cable 4 Operating Instruction Operating Instructions PANEL DESCRIPTIONS Transmitter Panel O wo INCU pOH Snes Him HDMI Over IP Transmitter Ethernet Indicator of power input 2 Status of sign
9. transmitters is TX1 0001 TX2 0101 TX3 0100 lf you need display Source2 on TV1 then just set Group ID of RX1 same as TX2 0101 refer to Diagram Operating Instructions No need power adapter for TX amp RX when connecting with POE Switch DVD 1 DVD 2 SS f m E e a H a ioe e T_n a a T i i Group 0 0001 Group D0101 Group D0100 k 4 i pen 7 i ie i Giga PoE Web smani swich i c Cia Cabs j sai Group ID same as TAZ 0101 Modify all TX and all RX for a different IP amp MAC address in LAN local area network to avoid conflict g Operating Instructions Setup HDMI TX and HDMI RX A HTTP server is embedded in each TX and RX you can setup IP address for HDMI extender via web browser The default IP address of the TX is 192 168 168 55 MAC address is 00 0b 78 00 60 01 The default IP address of the RX is 192 168 168 56 MAC address is 00 0b 78 00 60 02 Step 1 Assign the PC or laptop IP address on the computer Control Panel Network Connections gt Local Area Connections Status gt Properties Internet Protocol TCP IP Type the IP address field with 192 168 168 11 0 255 and Subnet mask with 255 255 255 0 After that press OK to save the configuration Note The IP address of PC should be different from the IP address of TX and RX step 2 Use an Ethernet Cable to connect the PC or laptop and the extender
10. your product during the warranty period This Limited Warranty is extended only to the original purchaser and only covers product purchased as new A purchase receipt or other proof of original purchase date is required for Limited Warranty service MAIL IN SERVICE When shipping the unit carefully pack and send it prepaid adequately insured and preferably in the Original carton Include a letter detailing the complaint and provide a day time phone and or email address where you can be reached 10 Operating Instructions LIMITED WARRANTY LIMITS AND EXCLUSIONS 1 This Limited Warranty ONLY COVERS failures due to defects in materials or workmanship and DOES NOT COVER normal wear and tear or cosmetic damage The Limited Warranty ALSO DOES NOT COVER damages which occurred in shipment or failures which are caused by products not supplied by warrantor or failures which result from accidents misuse abuse neglect mishandling misapplication alteration faulty installation set up adjustments misadjustment of consumer controls improper maintenance power line surge lightning damage modification or service by anyone other than a Factory Service center or other Authorized servicer or damage that is attributable to acts of God 2 THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER LIMITED WARRANTY COVERAGE THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREA
Download Pdf Manuals
Related Search