SOLAR CHARGE CONTROLLER OPERATING INSTRUCTIONS
Contents
1. MAKE FURTHER INSTALLATION UNTIL MISTAKE REMOVED AND LED 3 GOES OFF LED 2 RED LVD INDICATOR LED 2 WILL LIGHT WHEN BATTERY VOLTAGE 4 FALLS BELOW LVD SETPOINT AND LOAD IS DICONNECTED THE LED WILL TURN OFF WHEN BATTERY VOLTAGE IS BACK TO RECONNECT SETPOINT INSTALLATION 1 SET BATTERY CHARGE VOLTAGE BY SWITCH FIGURE 1 NO 7 2 CABLES AWG 12 FOR 12V 13A AWG 10 FOR 12V 25A 3 CONNECT BATTERY TO BATTERY FIGURE 1 NO 3 AND BATTERY FIGURE 1 NO 4 CHECK POLARITY BEFORE MAKING CONNECTION IF LED 3 LIGHTS ON REMOVE CONNECTION AND MAKE POLARITY CORRECT IF LED 2 LIGHTS ON THE BATTERY VOLTAGE IS BELOW 12 5V THE LIGHT WILL AUTOMATIGALLY TURN OFF WHEN THE BATTERY VOLTAGE RISES ABOVE 12 5V 4 COVER SOLAR PANEL DURING INSTALLATION AND MAKE CERTAIN THE PANEL POLARITY IS CORRECT CONNECT PV ARRAY TO SOLAR PANEL FIGURE 1 NO 1 AND SOLAR PANEL FIGURE 1 NO 2 LED 1 WILL LIGHT ON WHEN SUNLIGHT IS AVAILABLE DO NOT SHORT PV ARRAY WHEN CONNECTED TO THE CHARGER 5 TURN OFF LOAD AND MAKE CGONNECTION TO LOAD FIGURE 1 NO 5 AND LOAD FIGURE 1 NO 6 THEN TURN ON THE LOAD IF LED 2 LIGHTS ON THE BATTERY VOLTAGE IS TOO LOW CHARGE BEFORE TURN ON THE LOAD NOTE LOADS EXCEED CHARGER S RATED CURRENT SHOULD BE CONNECT TO BATTERY DIRECTLY INSTEAD OF LOAD AND LOAD TERMINALS INSTALLATION NOTES 1 CONNECT TO NEGATIVE GROUNDED SYSTEMS ONLY ALL NEGATIVE TERMINALS SHARES C2. OMMON GROUND 2 THE UNIT MUST BE PROTECTED FROM RAIN AND DIRECT SUNSHINE AND MUST BE INSTALLED WITH AIR VETILATION 3 DO NOT EXCEED CONTROLLER S VOLTAGE AND CURRENT MAXIMUM RATING AS IN SPECIFICATION SECTION 4 CONNECT LOADS EXCEED CHARGER S RATING DIRECTLY TO BATTERY NOT TO THE UNIT 5 DO NOT SHORT PV ARRAY OR LOAD WHEN CONNECTED THIS WILL DAMAGE THE CHARGER 6 DO NOT REMOVE BATTERY WHEN LOAD IS ON SPECIFICATIONS Article No 12V 13A 12V 20A Battery Voltage 12V 12V Charging end voltage 14 4V 14 1V 14 4V 14 1V Maximum PV panel open circuit 25V 25V Maximum PV panel short circuit 13A 25A Continuous load charge current 10A 20A No load Current No Load and PV 10mA 10mA Low voltage disconnect 11 5 0 1V 11 5 0 1V LVD reconnect 12 5 0 1V 12 5 0 1V Temperature Compensation 0 025V C 0 025V C Dimension L x W x H 134 2 58 4 33 mm 134 2 58 4 33 mm Weight 2009 2009
3. SOLAR CHARGE CONTROLLER OPERATING INSTRUCTIONS THE TBSC SERIES SOLAR CHARGE CONTROLLER IS DESIGNED TO CHARGE WET OR SEALED LEAD ACID BATTERIES WITH 12V PHOTOVOLTAIC PANEL SYSTEMS IT CONTROLS CHARGING CONDITION AND KEEPS THE BATTERY IN OPTIMIZED WORKING LIFE LED 1 LED 3 7 LED 2 O o m O CHARGING REV POL VOLTAGE LVD ON SETTING SOLAR BATTERY LOAD hase ass ss 1 2 3 4 5 6 FIGURE 1 FEATURES SEALED WET BATTERY SELECT CHARGING VOLTAGE SETTING FIGURE 1 NO 7 14 4V SWITCH TO RIGHT SIDE FOR WET LEAD ACID BATTERY 14 1V SWITCH TO LEFT SIDE FOR SEALED BATTERY REVERSE CURRENT BLOCKING BLOCK CURRENT FROM BATTERY TO PV ARRAY AT NIGHT LOW VOLTAGE DISCONNECT RECONNECT DISCONNECT LOAD FIGURE 1 NO 5 amp 6 WHEN BATTERY VOLTAGE DROPS TO 11 5V TO PROTECT BATTERY FROM HARMFUL DEEP DISCHARGES RECONNECT LOAD WHEN BATTERY VOLTAGE RECOVERS TO 12 5V TEMPERATURE COMPENSATION A BUILT IN SENSOR MEASURES TEMPERATURE CONDITIONS AND ADJUSTS CHARGING VOLTAGE WITH 0 025V C COMPENSATION ACCORDING TO 25 C REFERENCE POINT POLARITY PROTECTION THE UNIT IS PROTECTED FROM REVERSED CONNECTION OF BATTERY OR PANELS HOWEVER PV SYSTEMS OR OTHER LOAD MIGHT BE DAMAGED WHEN POLARITIES ARE REVERSED LED INDICATORS LED 1 GREEN CHARGING CONDITION ON WHEN SUNLIGHT IS AVAILBLE TO CHARGE OFF WHEN SUNLIGHT IS NOT AVAILBLE OR AT NIGHT LED 3 RED REVERSE POLARITY CONNECTION OF BATTERY OR SOLAR PANEL DO NOT
Download Pdf Manuals
Related Search