Home

FX3G-1DA-BD INSTALLATION MANUAL

1. 3 Termination of cable end Strip the coating of strand wire and twist the cable core before connecting it or strip the coating of single wire before connecting it An alternative connection is to use a ferrule with insulating sleeve Model Pressure bonding tool CRIMPFOX 61 ALO ee or CRIMPFOX 6T F 2 41 Old model name CRIMPFOX ZA 3 2 Old model name CRIMPFOX UD 6 Manufacturer Phoenix Contact Co Ltd Stick terminal with insulating sleeve Insulation sleeve Contact area Crimping area Strand wire single wire c SSS 0 35 2 6mm 0 1 When using a stick terminal with insulating sleeve choose a wire with proper cable sheath referring to the above outside dimensions or otherwise the wire cannot be inserted easily The tightening torque must be 0 22 to 0 25N m Do not tighten terminal screws exceeding the specified torque Failure to do so may cause equipment failures or malfunctions 4 Tool and CAUTION 1 Outline The FX3G 1DA BD board hereinafter called 1DA BD is an expansion board for Indicates that incorrect handling may cause hazardous lt gt DANGER conditions resulting in death or severe injury For the installation refer to the PLC main unit manual FX3G Series User s Manual Hardware Edition 3 Wiring WIRING Analog output expansion board FX3G 1DA BD PRECAUTIONS DANGER adding one additional analog output point Indicates that incorrect handling may cause
2. FX3G Series User s Manual Hardware Edition 4 3 Performance Specifications Specifications Voltage output 0 to 10V DC External load resistance 2kQ to 1MQ Item Current output 4 to 20mA DC External load resistance 5002 or less Analog output range Digital input 12 bits binary 11 bits binary Resolution 2 5mV 10V 4000 8uA 16mA 2000 0 5 50mV for full scale of 10V when ambient temperature is 25 C 5 C 1 0 100mV for full scale of 10V when ambient temperature is 0 C to 55 C Shipment adjustment is carried out by external load resistance 0 5 80uA for full scale 2kQ of 16mA when ambient y sea ar eam pe temperature is 25 C 5 C ecomes targer than kss Ne g 1 0 160uA for full output voltage will increase scale of 16mA slightly hen ambient temperatur When the load is 1MQ the When ambient temperature is 0 C to 55 C output voltage becomes about 2 higher than the correct value Caution An area of dead band is located in the region of OV Therefore the output analog value may not represent the digital value accurately Total accuracy D A conversion SOs ime The data will be updated at every scan time of the PLC 0 to 4000 are adjusted to 0 to 0 to 2000 are adjusted to 4 to 10V when the external load 20mA when the external load resistance is 2kQ resistance is 250Q output 10V 20mA characteristics z gt sed oj D
3. rela Holds the analog data output just z Macba Moar before stop of the PLC i ON Output the offset data at stop of the PLC D8260 D8270 Output setting data R W Error status b0 Output data setting error Special b1 Unused data D8268 D8278 b2 Unused R W register b3 Unused b4 EEPROM error b15 to b5 Unused D8269 D8279 Model code 4 R As for the details of the special devices refer to the following manual FX3G FX3U FX3UC Series User s Manual Analog Control Edition This manual confers no industrial property rights or any rights of any other kind nor does it confer any patent licenses Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial property rights which may occur as a result of using the contents noted in this manual Warranty Mitsubishi will not be held liable for damage caused by factors found not to be the cause of Mitsubishi opportunity loss or lost profits caused by faults in the Mitsubishi products damage secondary damage accident compensation caused by special factors unpredictable by Mitsubishi damages to products other than Mitsubishi products and to other duties e This product has been manufactured as a general purpose part for general industries and has not been designed or manufactured to be incorporated in a device or system used in purposes related to human life e Before using the product for special purposes such as nuclear p
4. 10V when ambient temperature is 0 C to 55 C Shipment adjustment is carried out by external load resistance 0 5 80uA for full scale 2kQ of 16mA when ambient w RA Par de temperature is 25 C 5 C ecomes arger tnan esa e o 41 0 160uA for full output voltage will increase scale of 16mA slighty hen ambient temperatur When the load is 1MQ the When ambie perature is 0 C to 55 C output voltage becomes about 2 higher than the correct value Caution An area of dead band is located in the region of OV Therefore the output analog value may not represent the digital value accurately Total accuracy D A conversion eves ima The data will be updated at every scan time of the PLC 0 to 4000 are adjusted to 0 to 0 to 2000 are adjusted to 4 to 10V when the external load 20mA when the external load resistance is 2kQ resistance is 2500 output 10V 20mA characteristics gt gt sed o v i c 2 o 4mA 5 Z 0 gt 40004080 8 gt 2000 2040 Digital input Digital input ey eon No insulation between the PLC method Occupied 0 point This number is not related to the maximum number of points input output points of the PLC 4 4 List of Special Devices R Read W Write Device number Description R W Switches the output mode Mpegs aoe ee OFF Voltage output ON Current output By Special Output Holding Function Cancellation fate ase Ids th log d j
5. hazardous NCAUTION 1 1 Incorporated Items Product conditions resulting in medium or slight personal injury or physical damage Depending on the circumstances procedures indicated by A CAUTION may also cause severe injury It is important to follow all precautions for personal safety Associated Manuals Manual name Description Describes specifications for EASGIEASWIEASUC vg97D16701 analog control and Series User s Manual f Analad Control MODEL CODE programming method for SANAJ SONTO 09R619 FX3G FX3U FX3UC Series Edition PLC FX3G Series JY997D31301 Explains FX3G Series PLC MODEL CODE 09R521 User s Manual Hardware Edition specifications for I O wiring installation and maintenance How to obtain manuals For product manuals or documents consult with the Mitsubishi Electric dealer from who you purchased your product Applicable standards FX3G 1DA BD units made in November 2008 or later comply with the EC Directive EMC Directive Further information can be found in the following manual FX3G Series Hardware Manual Manual No JY997D33401 Included items e M3x8 tapping screws for installation 2 pcs e Side cover e Installation Manual This manual 1 2 External Dimensions Part Names 4 3 2 1 6 Unit mm inches 5 Connector cover is removed MITSUBISHI A MASS Weight 20g 0 05Ibs 15 1 0 6 14 1 0 56 1 T
6. short as possible 4 Specifications STARTUP AND MAINTENANCE PRECAUTIONS CAUTION e Do not disassemble or modify the PLC Doing so may cause fire equipment failures or malfunctions For repair contact your local Mitsubishi Electric distributor e Do not drop the product or exert strong impact to it Doing so may cause damage DISPOSAL PRECAUTIONS CAUTION e Please contact a certified electronic waste disposal company for the environmentally safe recycling and disposal of your device TRANSPORT AND STORAGE PRECAUTIONS CAUTION e The product is a precision instrument During transportation avoid any impacts Failure to do so may cause failures in the product After transportation verify the operations of the product 4 1 Applicable PLC Model name Applicability FX3G Series PLC Ver 1 10 or later The version number can be checked by monitoring D8001 as the last three digits indicate it e The number of connectable expansion boards varies depending on the main unit as follows FX3G 14ML 24ML Main units 1 unit FX3G 40ML 60ML Main units 2 units Never stack up two or more expansion boards For details on the system configuration refer to the following manual FX3G FX3U FX3UC Series User s Manual Analog Control Edition 4 2 General Specifications The general specifications are equivalent to the PLC main unit For general specifications refer to the following manuals
7. EA 2 o 4mA 5 S S 0 gt 4000 4080 gt 2000 2040 Digital input Digital input Insulation No insulation between the PLC method Occupied 0 point This number is not related to the maximum number of points input output points of the PLC 4 4 List of Special Devices R Read W Write Device number Description R W Switches the output mode MAEN Ma2 OFF Voltage output ON Current output PN Special Output Holding Function Cancellation P Oren Ids th log d j rela Holds the analog data output just i Madot Modra before stop of the PLC oe ON Output the offset data at stop of the PLC D8260 D8270 Output setting data R W Error status b0 Output data setting error Special b1 Unused data D8268 D8278 b2 Unused R W register b3 Unused b4 EEPROM error b15 to b5 Unused D8269 D8279 Model code 4 R As for the details of the special devices refer to the following manual FX3G FX3U FX3UC Series User s Manual Analog Control Edition This manual confers no industrial property rights or any rights of any other kind nor does it confer any patent licenses Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial property rights which may occur as a result of using the contents noted in this manual Warranty Mitsubishi will not be held liable for damage caused by factors found not to be the cause of Mitsubishi opportunity loss or lost profits caus
8. Failure to do so may cause equipment failures or malfunctions 4 Tool For tightening the terminal use a commercially available small The FX3G 1DA BD board hereinafter called 1DA BD is an expansion board for FX3G Series User s Manual Hardware Edition adding one additional analog output point 1 1 Incorporated Items Product 3 Wiring WIRING PRECAUTIONS A CAUTION Indicates that incorrect handling may cause hazardous DANGER conditions resulting in death or severe injury Indicates that incorrect handling may cause hazardous NCAUTION conditions resulting in medium or slight personal injury or physical damage Analog output expansion board FX3G 1DA BD DANGER e Make sure to cut off all phases of the power supply externally before attempting e M3x8 tapping screws for installation 2 pcs With e Side cover Included items straight tip Depending on the circumstances procedures indicated by NCAUTION may also cause severe injury It is important to follow all precautions for personal safety Associated Manuals Manual name Description Describes specifications for EASGIEASWIEASUC vg97D16701 analog control and Series User s Manual f Analog Control MODEL CODE programming method for See eee 09R619 FX3G FX3U FX3UC Series Edition PLC FX3G Series JY997D31301 Explains FX3G Series PLC MODEL CODE 09R521 User s Manual Hardware Edition specifications for I O wiring installation an
9. Ratingen Germany Caution for EC Directive The analog expansion boards have been found to be compliant to the European standards in the aforesaid manual and directive However for the very best performance from what are in fact delicate measuring and controlled output device Mitsubishi Electric would like to make the following points As analog devices are sensitive by nature their use should be considered carefully For users of proprietary cables integral with sensors or actuators these users should follow those manufacturers installation requirements Mitsubishi Electric recommend that shielded cables should be used If NO other EMC protection is provided then users may experience temporary loss or accuracy between 10 in very heavy industrial areas However Mitsubishi Electric suggest that if adequate EMC precautions are followed for the users complete control system users should expect accuracy as specified in this manual e Sensitive analog cable should not be laid in the same trunking or cable conduit as high voltage cabling Where possible users should run analog cables separately e Good cable shielding should be used When terminating the shield at Earth ensure that no earth loops are accidentally created e When reading analog values EMC accuracy can be improved out by averaging the readings This can be achieved either through functions on the analog expansion boards or through a users program in the FX3G Series PLC ma
10. acturer This manual describes the part names dimensions mounting and PRECAUTIONS specifications of the product Before use read this manual and the manuals of all relevant products fully to acquire proficiency in handling and operating the product Make sure to learn all the product information safety information and precautions Store this manual in a safe place so that it can be taken out and read whenever followed for the users complete control system users should expect accuracy necessary Always forward it to the end user Registration as specified in this manual The company and product names described in this manual are registered e Sensitive analog cable should not be laid in the same trunking or cable trademarks or the trademarks of their respective companies conduit as high voltage cabling Where possible users should run analog Effective October 2010 a tasalateas DON Specifications are subject to change without notice e Good cable shielding should be used When terminating the shield at Earth enter the ventilation slits 2008 Mitsubishi Electric Corporation ensure that no earth loops are accidentally created Failure to do so may cause fire equipment failures or malfunctions e When reading analog values EMC accuracy can be improved out by e Do not touch the conductive parts of the product directly averaging the readings This can be achieved either through functions on the Doing so may cause device failures or malfunc
11. alog Output For the terminal configuration refer to Subsection 1 2 1 Using voltage output Terminal Use 2 core shielded twisted pair cable for the analog output lines and separate the analog output lines from other power lines or inductive lines 2 The grounding resistance should be 100Q or less 3 3 Grounding Grounding should be performed as stated below e The grounding resistance should be 1002 or less e Independent grounding should be performed for best results When independent grounding is not performed perform shared grounding of the following figure For details refer to the following manual FX3G Series User s Manual Hardware Edition Other Other equipment equipment Independent grounding Shared grounding Common grounding Best condition Good condition Not allowed e The grounding wire size should be AWG 22 20 0 3 0 5 mm e The grounding point should be close to the PLC and all grounding wire should be as short as possible 4 Specifications STARTUP AND MAINTENANCE PRECAUTIONS Z CAUTION e Do not disassemble or modify the PLC Doing so may cause fire equipment failures or malfunctions For repair contact your local Mitsubishi Electric distributor e Do not drop the product or exert strong impact to it Doing so may cause damage DISPOSAL PRECAUTIONS CAUTION e Please contact a certified electronic waste disposal company for the environmentally safe re
12. cycling and disposal of your device TRANSPORT AND STORAGE PRECAUTIONS CAUTION e The product is a precision instrument During transportation avoid any impacts Failure to do so may cause failures in the product After transportation verify the operations of the product 4 1 Applicable PLC Model name Applicability FX3G Series PLC Ver 1 10 or later The version number can be checked by monitoring D8001 as the last three digits indicate it e The number of connectable expansion boards varies depending on the main unit as follows FX3G 14ML 24ML Main units 1 unit FX3G 40ML 60ML Main units 2 units Never stack up two or more expansion boards For details on the system configuration refer to the following manual FX3G FX3U FX3UC Series User s Manual Analog Control Edition 4 2 General Specifications The general specifications are equivalent to the PLC main unit For general specifications refer to the following manuals FX3G Series User s Manual Hardware Edition 4 3 Performance Specifications Specifications Voltage output Current output Item Analoa output 0 to 10V DC 4 to 20mA DC ran oe P External load resistance External load resistance g 2kQ to 1MQ 5002 or less Digital input 12 bits binary 11 bits binary Resolution 2 5mV 10V 4000 8uA 16mA 2000 0 5 50mV for full scale of 10V when ambient temperature is 25 C 5 C 1 0 100mV for full scale of
13. d maintenance How to obtain manuals For product manuals or documents consult with the Mitsubishi Electric dealer from who you purchased your product Applicable standards FX3G 1DA BD units made in November 2008 or later comply with the EC Directive EMC Directive Further information can be found in the following manual FX3G Series Hardware Manual Manual No JY997D33401 e Installation Manual This manual 1 2 External Dimensions Part Names Unit mm inches 4 5 Connector cover is removed 3 MITSUBISHI A 2 1 MASS Weight 20g 0 05Ibs 15 1 14 1 0 6 0 56 6 1 Terminal block mounting screws 2 POW LED Lit while power is properly supplied from main unit 3 Mounting holes 2 03 2 4 Connector cover 5 Main unit connector 6 Terminal block to connect analog output 7 Memory casette Display module connector WIRING PRECAUTIONS installation or wiring work Failure to do so may cause electric shock or damage to the product CAUTION e Make sure to cut off all phases of the power supply externally before attempting installation or wiring work Failure to do so may cause electric shock or damage to the product Make sure to observe the following precautions in order to prevent any damage to the machinery or accidents due to abnormal data written to the PLC under the influence of noise 1 Do not bundle the main circuit line tog
14. e The analog expansion boards have been found to be compliant to the European standards in the aforesaid manual and directive However for the very best performance from what are in fact delicate measuring and controlled output device Mitsubishi Electric would like to make the following points As analog devices are sensitive by nature their use should be considered carefully For users of proprietary cables integral with sensors or actuators these users should follow those manufacturers installation requirements Mitsubishi Electric recommend that shielded cables should be used If NO other EMC protection is provided then users may experience temporary loss or accuracy between 10 in very heavy industrial areas However Mitsubishi Electric suggest that if adequate EMC precautions are INSTALLATION 2 wire 2 pieces of 0 3mm2 AWG22 PRECAUTIONS DANGER e Make sure to cut off all phases of the power supply externally before attempting installation or wiring work Failure to do so may cause electric shock or damage to the product 3 Termination of cable end Strip the coating of strand wire and twist the cable core before connecting it or strip the coating of single wire before connecting it An alternative connection is to use a ferrule with insulating sleeve Model Pressure bonding tool CRIMPFOX 61 ALO ee or CRIMPFOX 6T F 2 41 Old model name CRIMPFOX ZA 3 2 Old model name CRIMPFOX UD 6 Manuf INSTALLATION anuf
15. ed by faults in the Mitsubishi products damage secondary damage accident compensation caused by special factors unpredictable by Mitsubishi damages to products other than Mitsubishi products and to other duties e This product has been manufactured as a general purpose part for general industries and has not been designed or manufactured to be incorporated in a device or system used in purposes related to human life e Before using the product for special purposes such as nuclear power electric power aerospace medicine or passenger movement vehicles consult with Mitsubishi Electric e This product has been manufactured under strict quality control However when installing the product where major accidents or losses could occur if the product fails install appropriate backup or failsafe functions in the system afa MITSUBISHI ELECTRIC CORPORATION HEAD OFFICE TOKYO BUILDING 2 7 3 MARUNOUCHI CHIYODA KU TOKYO 100 8310 JAPAN HIMEJI WORKS 840 CHIYODA CHO HIMEJI JAPAN
16. ening torque should follow the specifications in the manual screwdriver having a straight form that is not widened toward the end as shown right 0 4mm 2 5mm Caution 0 02 gt P If the diameter of screwdriver grip is too small tightening torque will not be able to be achieved Use the following recommended screwdriver or an appropriate replacement grip diameter approximately 25mm 0 98 Manufacturer Phoenix Contact Co Ltd SZS 0 4x2 5 3 2 Wiring of Analog Output For the terminal configuration refer to Subsection 1 2 1 Using voltage output Terminal Use 2 core shielded twisted pair cable for the analog output lines and separate the analog output lines from other power lines or inductive lines 2 The grounding resistance should be 100Q or less 3 3 Grounding Grounding should be performed as stated below e The grounding resistance should be 1002 or less e Independent grounding should be performed for best results When independent grounding is not performed perform shared grounding of the following figure For details refer to the following manual FX3G Series User s Manual Hardware Edition Other Other Q Q Q Independent grounding Common grounding Best condition Not allowed Shared grounding Good condition e The grounding wire size should be AWG 22 20 0 3 0 5 mm e The grounding point should be close to the PLC and all grounding wire should be as
17. erminal block mounting screws 2 POW LED Lit while power is properly supplied from main unit 3 Mounting holes 2 03 2 4 Connector cover 5 Main unit connector 6 Terminal block to connect analog output 7 Memory casette Display module connector WIRING PRECAUTIONS e Make sure to cut off all phases of the power supply externally before attempting installation or wiring work Failure to do so may cause electric shock or damage to the product CAUTION e Make sure to cut off all phases of the power supply externally before attempting installation or wiring work Failure to do so may cause electric shock or damage to the product Make sure to observe the following precautions in order to prevent any damage to the machinery or accidents due to abnormal data written to the PLC under the influence of noise 1 Do not bundle the main circuit line together with or lay it close to the main circuit high voltage line or load line Otherwise noise disturbance and or surge induction are likely to take place As a guideline lay the control line at least 100mm 3 94 or more away from the main circuit or high voltage lines 2 Ground the shield wire or shield of the shielded cable at one point on the PLC However do not use common grounding with heavy electrical systems Make sure to properly wire to the European terminal board in accordance with the following precautions Failure to do so may cause electric shock equipment fail
18. ether with or lay it close to the main circuit high voltage line or load line Otherwise noise disturbance and or surge induction are likely to take place As a guideline lay the control line at least 100mm 3 94 or more away from the main circuit or high voltage lines 2 Ground the shield wire or shield of the shielded cable at one point on the PLC However do not use common grounding with heavy electrical systems Make sure to properly wire to the European terminal board in accordance with the following precautions Failure to do so may cause electric shock equipment failures a short circuit wire breakage malfunctions or damage to the product The disposal size of the cable end should follow the dimensions described in the manual Tightening torque should follow the specifications in the manual Twist the end of strand wire and make sure that there are no loose wires Do not solder plate the electric wire ends Do not connect more than the specified number of wires or electric wires of unspecified size Affix the electric wires so that neither the terminal block nor the connected parts are directly stressed Make sure to properly wire to the FX3G Series PLC in accordance with the following precautions Failure to do so may cause electric shock equipment failures a short circuit wire breakage malfunctions or damage to the product The disposal size of the cable end should follow the dimensions described in the manual Tight
19. in unit A 1 2 1 INSTALLATION PRECAUTIONS INSTALLATION PRECAUTIONS Terminal Layout Installation DANGER e Make sure to cut off all phases of the power supply externally before attempting installation or wiring work Failure to do so may cause electric shock or damage to the product CAUTION e Use the product within the generic environment specifications described in PLC main unit manual Hardware Edition Never use the product in areas with excessive dust oily smoke conductive dusts corrosive gas salt air Cl2 H2S SO2 or NO2 flammable gas vibration or impacts or exposed to high temperature condensation or rain and wind If the product is used in such conditions electric shock fire malfunctions deterioration or damage may occur e When drilling screw holes or wiring make sure cutting or wire debris does not enter the ventilation slits Failure to do so may cause fire equipment failures or malfunctions e Do not touch the conductive parts of the product directly Doing so may cause device failures or malfunctions e Connect expansion board securely to their designated connectors Loose connections may cause malfunctions 3 1 Applicable Cable and Terminal Tightening Torque 3 1 1 Terminal block European type 1 Wire size Wiring to analog device should use 20 22 AWG wire 2 Applicable cable Type Wire size Single wire 0 3mm2 to 0 5mm AWG22 to 20 2 wire 2 pieces of 0 3mm AWG22
20. ower electric power aerospace medicine or passenger movement vehicles consult with Mitsubishi Electric e This product has been manufactured under strict quality control However when installing the product where major accidents or losses could occur if the product fails install appropriate backup or failsafe functions in the system a MITSUBISHI ELECTRIC CORPORATION HEAD OFFICE TOKYO BUILDING 2 7 3 MARUNOUCHI CHIYODA KU TOKYO 100 8310 JAPAN HIMEJI WORKS 840 CHIYODA CHO HIMEJI JAPAN Side JY99 D33601D A B E A JAPANESE B ENGLISH Attention 1 2 1 Terminal Layout 3 1 Applicable Cable and Terminal Tightening Torque e This product is designed for use in industrial applications 3 1 4 Terminal block European type MITSUBISHI Changes for the Better mete 1 Wire size e Manufactured by Mitsubishi Electric Corporation 2 7 3 Marunouchi Chiyoda ku Tokyo 100 8310 Japan e Manufactured at Mitsubishi Electric Corporation Himeji Works Wiring to analog device should use 20 22 AWG wire 2 Applicable cable PROGRAMMABLE CONTROLLERS MELSEG F _ ie 840 Chiyoda machi Himeji Hyogo 670 8677 Japan Type Wire size FX3G 1DA BD e Authorized Representative in the European Community 2 llati Sinale wire 0 3mm to 0 5mm2 AWG22 to 20 INSTALLATION MANUAL MANUAL Mitsubishi Electric Europe B V Installation g amm to Damm o 20 eeo pooo AN 3G e em Gothaer Str 8 40880 Ratingen Germany Caution for EC Directiv
21. side JY997D33601D B Fa JAPANESE S E ENGLISH Aa MITSUBISHI PROGRAMMABLE CONTROLLERS MELSEG F Changes for the Better FX3G 1DA BD INSTALLATION MANUAL Manual Number JY997D33601 ewe o This manual describes the part names dimensions mounting and specifications of the product Before use read this manual and the manuals of all relevant products fully to acquire proficiency in handling and operating the product Make sure to learn all the product information safety information and precautions Store this manual in a safe place so that it can be taken out and read whenever necessary Always forward it to the end user Registration The company and product names described in this manual are registered trademarks or the trademarks of their respective companies Effective October 2010 Specifications are subject to change without notice 2008 Mitsubishi Electric Corporation F X3G Safety Precaution Read these precautions before use This manual classifies the safety precautions into two categories Attention e This product is designed for use in industrial applications Note e Manufactured by Mitsubishi Electric Corporation 2 7 3 Marunouchi Chiyoda ku Tokyo 100 8310 Japan e Manufactured at Mitsubishi Electric Corporation Himeji Works 840 Chiyoda machi Himeji Hyogo 670 8677 Japan e Authorized Representative in the European Community Mitsubishi Electric Europe B V Gothaer Str 8 40880
22. tions analog xDalision Boards AE Aron gN a Users Proghant ti Iie sae SETE e Connect expansion board securely to their designated connectors CAUTION e Use the product within the generic environment specifications described in PLC main unit manual Hardware Edition Never use the product in areas with excessive dust oily smoke conductive dusts corrosive gas salt air Cl2 H2S SO2 or NO2 flammable gas vibration or impacts or exposed to high temperature condensation or rain and wind If the product is used in such conditions electric shock fire malfunctions deterioration or damage may occur e When drilling screw holes or wiring make sure cutting or wire debris does not Phoenix Contact Co Ltd Stick terminal with insulating sleeve Insulation sleeve Contact area Crimping area Strand wire single wire c SSS 0 35 Safety Precaution Read these precautions before use PLC main unit 2 6mm 0 1 This manual classifies the safety precautions into two categories Loose connections may cause malfunctions When using a stick terminal with insulating sleeve choose a wire with proper DANGER and A CAUTION 1 Outline For the installation refer to the PLC main unit manual cable sheath referring to the above outside dimensions or otherwise the wire cannot be inserted easily The tightening torque must be 0 22 to 0 25N m Do not tighten terminal screws exceeding the specified torque
23. ures a short circuit wire breakage malfunctions or damage to the product The disposal size of the cable end should follow the dimensions described in the manual Tightening torque should follow the specifications in the manual Twist the end of strand wire and make sure that there are no loose wires Do not solder plate the electric wire ends Do not connect more than the specified number of wires or electric wires of unspecified size Affix the electric wires so that neither the terminal block nor the connected parts are directly stressed Make sure to properly wire to the FX3G Series PLC in accordance with the following precautions Failure to do so may cause electric shock equipment failures a short circuit wire breakage malfunctions or damage to the product The disposal size of the cable end should follow the dimensions described in the manual Tightening torque should follow the specifications in the manual For tightening the terminal use a commercially available small screwdriver having a straight form that is not widened toward the end as shown With straight tip right 0 4mm 2 5mm Caution 0 02 spe 0 1 If the diameter of screwdriver grip is too small tightening torque will not be able to be achieved Use the following recommended screwdriver or an appropriate replacement grip diameter approximately 25mm 0 98 Manufacturer Phoenix Contact Co Ltd SZS 0 4x2 5 3 2 Wiring of An

FX3G-1DA-BD INSTALLATION MANUAL

Contents

Download Pdf Manuals

Related Search

Related Contents