PDS200 Power over Ethernet Device Server User Manual
Contents
1. present data connection and overrun can be displayed at the same time Status LED behavior in Monitor Firmware Fast blinking pattern means that neither application firmware nor the NetLoader can be found in the FLASH memory of the PDS200 The way out of this situation is to upload application firmware and the NetLoader into the device via its serial port the serial upgrade was completed successfully Slow blinking Red Status LED means that there was a timeout while waiting for the XMODEM data If this happens right in the beginning of the serial upgrade then most probably this is caused by incorrect serial settings on the PC side incorrect serial cable wiring or incorrect XMODEM start procedure XMODEM must be started on the PC first and only then the DS is switched on with he Setup button pressed Note Setup button is nearby EM203 module in the case Communications error This pattern means that an error was detected on the protocol level in XMODEM communications Most often this means that incorrect communications parameters are set on the PC side Firmware file is too big This pattern means that the file you are trying to upload into the PDS200 is too big Check if you have selected a correct file FLASH failure This pattern means that internal FLASH memory of the PDS200 is malfunctioning Note Please refer to Device Server Toolkit DST software for Windows under item Software Manuals in HTML Help file sois_ manu2. 00 has tried to connect Link Server login in progress Means that the PPPoE login failed Occurs at startup and means that either PPPoE login name and password defined by PPPoE Login Name PL and PPPoE Login Password PD settings are incorrect or PAP authentication protocol used by the PDS200 is not supported by Access Concentrator with any network host is currently established TCP connection is being opened Indicates that TCP connection either incoming or outgoing is being established i e SYN SYN ACK exchange is in progress PDS200 has already established TCP connection to the Link Server and is now attempting to login Link Server login failed Means that data connection to the Link Server could be TM951218 established but the server has rejected this PDS200 because the data in the Owner Name ON Device Name DN or Password PW setting is incorrect or for some other reason Data connection is established or being closed Means that data UDP connection or TCP connection is currently established or that TCP connection is being closed i e FIN ACK FIN ACK exchange is in progress Data is being routed no overruns detected This pattern is played when the data connection is established and the data is being routed through the PDS200 Buffer overrun no data routing This pattern is displayed when the data connection is established and the routing buffer overrun has been detected within the
3. Follow the descriptions below to learn more about the behavior of these LEDs under different conditions Status LED behavior in Application Firmware Powerup pattern This pattern is played once when the PDS200 is switched on Buzz pattern Both LEDs blink fast this pattern is played when the PDS200 receives the Buzz B command This is used to identify a particular PDS200 Status LEDs of the PDS200 are playing a serial ee programming mode pattern when the serial port of the PDS200 is in the serial programming mode Status LEDs of the PDS200 are playing an error mode pattern when the PDS200 is in the error mode unless the serial port of the PDS200 is in the serial programming mode Ethernet Port failure Indicates that the Ethernet port hardware is malfunctioning and network communications with the PDS200 is not possible IP address not obtained Occurs at startup when DHCP DH setting is 1 enabled and the PDS200 has not yet obtained its IP address from the DHCP server Data connection is closed This pattern as means that no data connection TCP or UDP so the PDS200 is idle Sending ARP Displayed when the PDS200 is sending ARP requests to find out MAC address of the destination network host with which the PDS200 is about to establish a connection TCP connection reset rejected by the network host Means that the TCP connection has been reset using RST packet by the network host to which the PDS2
4. PDS200 Power over Ethernet Device Server User Manual E ABOUT PDS200 is an external usage Power over Ethernet Device Server Serial to Ethernet converter It includes the function of GIGA TMS s products DS203 Device Server and PS200 Power over Ethernet Splitter It can connect existing serial device RS232 or RS485 to Ethernet network and supplies DC12V or DC5V output for the serial device RS232 or RS485 It has RS232 and RS485 serial ports You can set the output signal to RS232 or RS485 by adjusting the DIP Switch that located at the bottom case of PDS200 The product offers a compact disk which includes Tibbo Device Server Toolkit software and Virtual Serial Port driver for Windows and Linux To manipulate Ethernet and serial s settings please refer to Tibbo Device Server Toolkit Documentation E APPLICATION For those areas that AC power is not available PDS200 provides the easiest way to power Ethernet device supply DC12V or DC5V power The hardware of PDS200 includes an Auto MDIX 10 100BaseT Ethernet port a RS232 serial port a RS485 serial port and an internal processor that glues network and serial sides together From the hardware standpoint PDS200 can be regarded as a universal platform that is suitable to run a variety of network and serial communication applications Most functions of PSD200 are provided by Application Firmware PDS200 runs in Application Firmware Serial to Ethernet mode that turns the
5. PDS200 into a ready to work serial to Ethernet converter that can connect almost any kind of serial device to Ethernet TCP IP network Application Firmware has fixed function If you want to adjust the behavior of PDS200 you can specify the values of programmable parameters settings defined in this firmware In addition Application Firmware of PDS200 can be upgraded and firmware upgrade is via serial port or Ethernet port Serial upgrade is facilitated by a so called Monitor a fixed service firmware inside the PDS200 Network upgrade relies on the Application Firmware itself there is a self upgrade algorithm with Tibbo Device Server Toolkit software Auto MDIX means automatic detection of straight and cross cables Mi FUNCTIONALITY DC12V or DCS5V output for RS232 or RS485 device Full and half duplex serial port modes Server Client and Server Client network routing modes Numerous options for connection serial port etc 8KB data buffers one in each direction Configuration stored in EEPROM Setup through the serial port or network UDP Telnet Remote control of RTS CTS DTR and DSR lines On the fly commands for immediate serial port configuration TM951218 Serial side modem commands for network connection control Direct control of ADSL modem Support UDP TCP ARP ICMP ping DHCP PPPoE LCP i SPECIFICATIONS Broduci IEEE 802 3af Power over Ethernet Device Server Se
6. al in CD for more detail description about software DS Manager VSP Manager and Connection Wizard TM951218
7. llowing is pin assignment E RS232 Port Pin Assignment DB9M RS232 connector has the following pin assignment Ground _ _ Ground TM951218 E RS485 Port Pin Assignment RS485 connector has the following pin assignment T pin 2 is RS485 positive differential signal T R T pin 3 is RS485 negative differential signal T R Mi DC 5V Output 4P Connector The RS485 connector also supplies DC 5V power output Output 5V pin 1 correspond to ground GND pin 4 is DC5V output port this power can supply for RS232 or RS485 device which uses DC5V power source The DC5V tolerance range is 4 75VDC 5 25VDC and maximum output current is 240mA GIGA TMS supplies a power cable WAS T0471 This cable originally is used for DC12V output If RS232 or RS485 device does not use DC12V power source you can use WAS T0471 as DC5V output cable by cutting the B end of WAS T0471 and then peeling the black cover of WAS W1T0471 around 2 0 cm and peeling the covers of inner red and white wires around 0 5 cm as the pictures below Then connect the red wire to output 5V pin 1 and connect the white wire to the ground GND pin 4 DC5V will be output from the A end of WAS 1T0471 for Serial Device usage Q WAS T0471 Red wire White wire WAS T0471 with black cover k A 1 5 cm 0 5 cm TM951218 Mi DC 12V Output DC Jack The DC jack of PDS200 accepts small power connector with 3 5mm diameter It
8. outputs DC12V power for RS232 or RS485 device Please use WAS T0471 power cable that supplied by GIGA TMS Output power tolerance range is 11 4VDC 12 6VDC and maximum output current is 660mA On the DC jack the ground is the outside circle shown on the figure as below 12VDC Output Ground Mi DIP Switch setting for RS485 communication The DIP Switch is located at the bottom case of PDS200 All DIP Switch set to ON position indicates that data is routed through PDS200 via RS485 port Mi DIP Switch setting for RS232 communication The DIP Switch is located at the bottom case of PDS200 All DIP Switch set to OFF position indicates that data is routed through PDS200 via RS232 port TM951218 W Status LEDs PDS200 PoE Device Server features one Power Status LED yellow LED and two Status LEDs red LED and green LED Yellow LED means that PoE function works normally and 12VDC is ready Red LED and green LED display various states of device operation The states of PDS200 are indicated by way of playing LED patterns Patterns are represented by graphics in the following manner The pattern means that both red LED and green LED blink three times together The pattern ee means that red LED makes one long blink and then two short ones i Gr les DC12V Out RS 232 RS 485 TM951218 Status LEDs red LED and green LED display various status information depending on what firmware is running at the moment
9. rial to Ethernet Converter Compliant to all IEEE 802 3af specifications eee ah Omen Present class 0 PD to PSE Extract power from data pair 1 2 3 6 spare pair 2 Pair 4 Pair Power Extraction 4 5 7 8 or both pairs PoE signature on any one pair Chemet Coneco PoE in 10 100BaseT auto MDIX Ethernet RS232 Connector RS232 mode RX TX RTS CTS DTR DSR lines Default settings 19200 N 8 1 DIP Switch all OFF RS485 mode RX TX automatic direction RS485 Connector control Default settings 19200 N 8 1 DIP Switch all ON DC 12V Output DC Jack 12VDC 660mA Max DC 5V Output 4P connector 5VDC 240mA Max internal circuit used partial power Powered Ethernet Cable TIA EIA 568 Category 5 5e cable Yellow PoE working normally and 12VDC ready LED Indicator Red DS operation under the error mode Green Network working normally 100 L 98 W 24 H mm Weight 150g Operating Environment 0 50 Degree C 5 90 RH Storage Environment 10 70 Degree C 5 90 RH E Ethernet Port Pin Assignment amp RS232 485 Port Pin Assignment gt TX No 5V connection 12VDC Error Link R 5 RS CTS No ofu x Xe N ts o x ve asos sp BE ve Rscrs 9 al _ X The mark DC12V Out on the right figure is output Power Jack SRONA DC12V Out RS 232 RS 485 TM951218 Mi Ethernet Port Pin Assignment Ethernet port of PDS200 is 10 100BaseT type Connector is RJ45 type The fo
Download Pdf Manuals
Related Search