Undercover User Manual
Contents
1. Undercover User Manual Front amp Rear View Master Slave Front Back Front Back Distance indication Buzzer Signal indication lates jl Power on ee Search button Hanging hole Power off Battery cover for strap Clip Battery cover Specifications uc A E low E Dimension LIW H 52 8x39x13 2mm 38x120x6 2mm f52 8x39x13 2mm 38x120x6 2mm 2x1 6x0 52inch 1 5x4 72x0 24inch 2x1 6x0 52inch 1 5x4 72x0 24inci Getting Start 1 For first time use please insert the batteries into the Master and the Slave sets according to the battery installation as follows CR2032x2 Master Slave a Slide out the battery cover b Insert the batteries Make sure that the polarity of the battery follow the markings on the bottom of the battery compartment c Place the battery cover back 2 Mark sure the Master is powered OFF in the first place and install the Slave on the bike in case the alarm is triggeved while installation take the Master with you or clip it on your belt 3 Switch the power button of the Master to ON Preferred setting place Master ZA ES Slave H eA UI p gt oa D OAS Z O D A 5 Search For searching the Slave unit please press the Search button on the Master unit once If the distance between the Master and the Slave is closer more LED lights are lit and the melody from the Master becomes more rapid Con2. n be damaged c Do not store the device in hot areas High temperatures can shorten the life of electronic device damage Batteries and warp or melt certain plastics d Do not store the device in cold areas When the device returns to its normal temperature moisture can from inside the device and damage electronic circut boards e Do not attempt to open the device other than as instructed in this guide f Do not drop knock or shake the device Rough handling can break internal circuit boards and fine mechanics g Do not use harsh chemicals cleaning solvents or strong detergents to clean the device h Do not paint the device paint can clog the moving parts and prevent proper operation i Do not put the master and the Slave at same place in case of this kit is unable playing functions to guard your valued goods j Search detection and alarm range depend on the terrain environment k If the beep sound is not loud enough the batteries may be low Change with new batteries for louder alarm sound I This product only assists in providing a warning alarm to remind the user It does not guarantee to prevent theft or robbery of personal property m If you want to use the device during flight trips please comply with the flight safety law according to each country n We reserve the right in changing the specification of the hardware and software designs to manuals at any time and without prior notice Information in thi
3. olding Way O Correct Holding Do not cover the top side of Master Alarm A sensor is bulit in to detect the vibration while someone is trying to move your bike the Bike Guard will alert you in 3 second Master amp Slave will alarm for 5 seconds and repeat alarm until vibration is stop Disarm Alarm Under standby mode turn OFF the Master unit within 3 meters from your bicycle and wait for the approval sound Di du on Master unit When you hear Di du you have disarmed Bike Guard Mute Press the Mute button to mute searching melody from the Master unit Listen to beep sound from the Slave unit to assist short range searching Wake up Standby a Switch Master amp Slave power On Master will enter wake up process The Signal indicator right and left LEDs blink while Master is waking Slave up within 8 15 seconds if Slave is within range and NOT being blocked After Slave been woken up Master enters Search mode Press Search key to go back to Standby mode b Under Standby mode Master s LED blinks every second When wake up Master enters Search mode automatically If Master cannot wake up Slave within 160 seconds due to out of range or signal is blocked it will enter Standby mode and beeps to indicate lost signal User can push Search key to enter wake up process again Important Please turn off the Master unit if NOT in use to save battery life Out of range or Loss signal a Master beeps
4. on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept an interference received including interference that may cause undesired operation FCC Caution Any changes or modifications are not expressly approved by the party responsible for compliance which could void the user s authority to operate this equipment EU Declaration Conformity This product is carrying the CE Mark in accordance with the related European Directives C 91E T1B6 U50G01
5. s document is subject to change without notice o This product operational temperature is between 32 F 131 F 0 C 50 C Storage Temperature is between 4 F 185 F 20 C 85 C Recycle The Batteries provided in this product should be recycled to protect the local environment Please contact your local recycle department for detail Warning Do not put the batteries into the fire or heat sources It may cause danger or even explosion FCC Certifications Federal Communication Commission Interference Statement This equipment has been tested and improved to comply with the limits of a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This FCC Certifications equipment generates uses and can radiate radio frequency energy if installed and used not in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determinedly turning the equipment off and on the user is encouraged to try to correct the interference by one of the following measures m Reorient or relocate the receiving antenna m Increase the separation between the equipment and receiver m Connect the equipment into an outlet
6. trarily if the distance between the Master and the Slave is farther less LED lights are lit and the melody from the Master becomes slower Use the LED and the melody indication as guides to find the Slave unit Aa ay PES working range 0 120 200 m 328 546 ft line of sight the distance may be short depends on the terrain environment Important a Under search mode always place the Master in front of your body and turn to different directions to check the signal If you point at the right direction The master will show lights and plays the melody more rapidly b If the distance between the Master and the Slave is out of detectable working range and you are turning into the wrong direction making the distance farther the Master plays the melody and beeps every second to remind you to go back to the right direction and detectable distance ASAP c If you want to stop the search mode press the Search button on the Master unit once d While searching the Slave makes low beep sounds every second This can assist you in finding its position by tracking the sound when the Master and the Slave are already close Suggestion Press and hold the mute button on the Master to turn of f the melody temporarily Once you release the mute button the searching melody resumes again During Search Correct Wrong Holding Holding Do not sway Master Master is always in front the body when take a turn H
7. vibrates and signal LED blinks for 160 seconds out of range or loss signal then Master will enter sleep mode automatically b master beeps once a minute to remind user to switch power OFF for Master unit for power saving c To wake up Master press Search button to go to wake up process Low battery When the Matser and Slave is under low battery condition it will beep at a 2 minutes interval please change the battery Important Under low battery condition it may cause abnormal function of alarm or searching Please Note a The connection range is based on clear line of sight Actual range will vary depending on user s environment and location b When the Master and Slave units are turned ON it takes 8 to 15 seconds for the synchronization c The signal will be disconnected while the Master and Slave units are too close within 10 cm the signal connection will be overloaded When the Master unit can t connect to Slave unit Master unit alarms every second and Slave unit s LED light flashes Care and Maintenance a The Slave units are water repellent but not waterproof Keep the device dry Precipitation humidity and all types of liquids or moisture can contain minerals that may corrode electronic circuits If your device gets wet remove the battery and allow the device to dry completely before replacing it b Do not use or store the device in dusty dirty areas as its moving parts and electronic components ca
Download Pdf Manuals
Related Search