After Use ASA Industrial Electric Screwdriver User's Manual
Contents
1. After Use Storage and maintenance if you do not plan to use the screwdriver for a long period unplug it or switch off the power source Store the screwdriver in a dry dust free place away from direct sunlight Inspect and maintain it periodically to ensure continued functioning Repair If the screwdriver is not operating normally do not attempt to disassemble it Contact one of our service agents Warranty We provide a one year free repair service warranty with this product The warranty is good for one year from the date of purchase entered on the Product Information Form The retailer s stamp must appear on the form to confirm the date However under the following circumstances we will charge the user for any parts and labor costs associated with repairs For repairs involving normal wear to parts including carbon brushes bits and power cord and also to the exterior surface If the screwdriver was connected to a power source of the incorrect voltage After the period of the guarantee or if the user cannot present the manual with stamped Product Information Form Please note e The retailer s stamp must appear on the Product Information Form in order to receive free repair service f the date is not filled in the guarantee takes effect from the date of product assembly We cannot replace this manual Please safeguard it Other points The adapte2. Check that product is completely assembled Check that the carbon maintance bonnet is closed tightly If the bonnet or spring connector have com loose the motor will automatically cut off the screwdriver will operate only after the have been correctly reassembled If the power cord is in any way damaged unplug the screwdriver immediately and exchange it for a new product in order to protect against short circuit Check the workplace Although this product features dual insulation to ensure safety do not use it in damp or high temperature environments or near flammable materials Keep the power cord away from tools and equipment that might damage or melt it Caution When plugging in or unplugging the power cord make sure to hold it by the plug Never not indicate torque output Actual torque can only be determined with a torque testing machine or hand held spanner torque tester If you have difficulty removing screws reverse setting increase torque by turning the regulating handle clockwise into the casing Inserting the bit Push the bit slide sleeve down with your finger and insert a suitable bit When the bit slide sleeve is released the bit will become engaged If the Push bit slide bit slide sleeve can not homing please pull out the bit sleeve in Count please change the 3 band switch forward amp reverse switch to middle band and don t beat o
3. This product comes supplied with a pair off carbon brushes and two bits Bits one set per screwdriver LSI 104 d aU 185 d TEE ANE d je 40 50 65 shank shank Bit specifications 04 0 d5 0 1 4 Hex shank 1 4Hex double end shank Available i A i Screwdriver a 8 Pik SR za Pik RA gable Pik oy RT Pik yog D D D D 00 gla TW 1202 00 pla 7W6204 AS 1631 00 92 0 7W1402 00 2 0 7W6404 AS 1632 0 92 5 7W1522 0 42 5 7W6524 AS 2631 1 94 0 7W1742 1 93 0 7W6644 AS 2632 1 3 0 7W3644 1 3 0 7W6644 1 6 35 7W7147 AS 3631 2 5 0 7W3864 2 94 5 7W6764 2 6 35 7W7167 AS 3632 1 3 0 7W3644 1 3 0 7W6644 1 6 35 7W7147 AS 4631 2 5 0 7W3864 2 96 0 7W6964 2 6 35 7W7167 AS 4632 S 1 95 0 7W3844 1 94 5 7W6744 2 6 35 7W7167 AS 6631 2 5 0 7W3864 2 6 0 7W6964 2 6 35 7W7167 AS 6632 Before Using Check voltage Please read the label on the product exterior and the manual thoroughly before using the screwdriver and make especially sure to correctly determine the screwdriver s voltage requirement 115VAC or 230VAC Only plug the screwdriver into an outlet with the correct voltage Check for suitable torque range Choose a screwdriver model that matches your required torque range To lengthen product life avoid using screwdrivers at maximum torque over long periods
4. described below Caution Always unplug the screwdriver before changing the brush Only use the factory specification brushes provided with the screwdriver as replacements 1 Insert a slotted bit with a 3 0mm wide 1 0mm thick head in the slot on the side of the carbon maintance bonnet and lever it up Open the bonnet pull the power cord forcibly Usage and Cautions Screw and unscrew settings To drive a screw set the forward reverse switch to the FWD position To remove a screw set the switch to the REV position Caution Never change the switch position when the motor is running Release the trigger power switch and change the position after the motor stops Torque setting Set the torque level by rotating the regulating handle Turning it clockwise into the casing will increase the torque and turning it counterclockwise out of the casing will decrease the torque Caution The markings on the regulating handle are for reference only and do 2 Remove the spring resting on the carbon brush 3 Lift the copper wire attached to carbon brush and pull the brush out 4 Pull out the tip of the copper wire and complete the removal 5 Insert the new carbon brush following the above steps in reverse order Guide for
5. carbon brush replacement Guide for 3P plug in STEP 1 STEP 2 STEP 3 STEP 4 guide notch ever c up pe i Se HED ola s i a WE I a convex point 43 zuj remove 108 i TF a 3P plug Position A z L 2 L LU VIEW OF POSITION A i receptacle screwdriver side OG ONI KK s B S Ow NA a lt gt W a 6 gt GP y ah S W d A H 886 3 5753170 HER J HAE 86 21 34970699 WEED E FREYI 86 755 83298787 Http www 100y com tw A REVISED 01 0507 L I C ZA NEW ASSEMBLY 07 03 02 HUANG MEM DATE NAME WE AS 1631 2 2631 2 A REVISED 04 20 00 HUANG 3631 2 4631 2 6631 2 DRAWN 1998 02 13 Y C HUNG disassemble graphic SYM DESCRIPTION DATE SIGN WROGA WI SA R g wo M10005 We d A 4 4 886 3 5753170 HER J EFEN 86 21 34970699 WEE J EPRE 86 755 83298787 Http www 100y com tw UNIT M M DESIGN DRAWN 2007 10 17 ASA 4631 2S NA disassemble graphic SYM DESCRIPTION DATE SIGN CHECKED APPROVED ASA ENTERPRISE CORP pwc No M10054
6. r force to pull out when inserting bit Inserting and removing single or double ended 1 4 hex bits Inserting the bit and arrive bottom then push the bit slide sleeve down with your finger the will be flip out Hang securely During use the screwdriver should be hung up securely to prevent it from failing and also to protect the power cord from sudden pulls Starting and stopping the motor Press the trigger power switch down to start the screwdriver And release it to stop Important points elf the clutch slips when screws are fully tightened i c Clicking sound is not heard when torque is reached immediately release the trigger power switch to prevent the motor from burning out due to continued power flow while it is not operating f the screwdriver is operating for a long period or if excessive current surges are experienced the screwdriver may overheat In this case it will switch off automatically When the heat has dispersed normal operation can resume Operational frequency suggest the operational frequency 1 4 ON OFF second the total screws 7000pcs 8hours don t over our operational frequency suggest and avoid the inside part of screwdriver serious damage If everyday work 8hours upward please use two screwdriver by turns protect the life of screwdrivers Changing the carbon brush When the carbon brush change indicator lights up red please Change it as
7. rs optional with many applications are available for use with this product However for drilling holes it should never be used on any material except plastic and wood less than 2mm thick and especially not on metal or walls Please note Drill bits may break off if the screwdriver is not held tightly or held at an angle to the drilling surface Take care of your hands and eyes Product Information Form Model Retailer s Stamp Serial No Date of Purchase Specifications and design may be changed without notice for improvement A 5 We 4 2 4 886 3 5753170 WER ETER 86 21 34970699 WERE TI EPRE 86 755 83298787 Http www 100y com tw Serial No ASA Industrial Electric Screwdriver User s Manual for semi automatic models strengthened tightening torque A Word of Thanks to Our Customers Thank you for choosing lightweight and powerful ASA electric screwdrivers In order to insure maximum performance and product life please read through this manual before using your screwdriver Features Our screwdrivers were designed for fastening screws They include many patented features Anti slip egg shaped body Patented carbon brush cover prevents shocks Indicator light shows when carbon brush needs replacement Integral dual insulation Centrifugal turbine heat dispersion Low noise transmission Patented power cord clip Screw driving applications range from a
8. ssembly of small items such as watches and eyewear to home appliances hardware furniture and other products Specifications Mad AS AS AS AS AS AS AS AS AS AS AS AS RUM 1631 1632 2631 2632 3631 3632 4631 46318 4632 46328 6631 6632 Power source 115 230 115 230 115 230 115 230 115 230 ACV 60HZ 50HZ 60HZ 50HZ 60HZ 50HZ 60HZ 50HZ 60HZ 50HZ Sas rapes 0 2 2 0 0 17 1 7 0 5 7 0 0 43 6 1 1 0 12 0 0 9 10 4 2 0 18 0 1 7 15 6 5 0 25 0 4 3 21 7 gf cm 1bf in No load speed rpm 1000 1000 1000 1000 1800 1000 1800 1000 Torque setting 2 Machine Screw 1 0 2 0 0 04 0 08 1 0 2 6 0 04 0 10 1 4 3 0 0 06 0 12 2 0 4 0 0 08 0 16 2 6 5 0 0 10 0 20 a2 mm in lt a 1 0 1 7 0 04 0 07 1 0 2 3 0 04 0 09 1 4 2 6 0 06 0 10 2 0 3 0 0 08 0 12 2 3 4 0 0 09 0 16 Weight g lb 400 0 88 480 1 0 Length mm in 228 9 0 Available bit shank d 4 0 4 5 0 5mm Hex shank 1 4 Hex shank 1 4 Hex double end shank Power consumption W 30 40 z Outline Lever start type yp FORWARD LEVER RING HANGER Cas 46328 JS N Ad I l 1 a gt 10 H uu ENGRAVINR RING REVERSE LEVER CARBON MAINTENANCE BONNET BIT SLIDE SLEEVE REGULATING HANDEL We 4 4 4 886 3 5753170 WERE EFEN 86 21 34970699 Accessories WEED E PREI 86 755 83298787 Http www 100y com tw
Download Pdf Manuals
Related Search